组装、冲压、喷漆等专业词汇
模具英语专业词汇
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine冲床robot机械手hydraulic machine油压机lathe车床|刨床 planer |'pleinmiller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' n|氧化 ksi'deiscratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良mp|镶块 embeded lump|in'bed| |l feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓to put file in order整理资料spare tools location手工备品仓equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品flow chart流程窗体assembly组装spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲metal plate钣金lathe车mill锉plane刨grind磨blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size------------------------------------------------------------------------------------------ 模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料销spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机。
专业英语(工厂一系列零配件专业词汇)
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion磨损
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试
Voltage switch of SPS电源电压接拉键
sheet metal parts冲件
plastic parts塑胶件
SOP制造作业程序
material check list物料检查表
to reverse material翻料
wet station沾湿台
Tiana天那水
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
专业英语——组装、冲压、喷漆、生产、工厂（工厂零配件等词汇）
冲压专业英语
组装、冲压、喷漆等专业词汇A s s e m b l y l i n e组装线L a y o u t布置图C o n v e y e r流水线物料板R i v e t t a b l e拉钉机R i v e t g u n拉钉枪S c r e w d r i v e r起子Electric screw driver电动起子Pneumatic screw driver气动起子w o r k t a b l e工作桌O O B A开箱检查fit together组装在一起f a s t e n锁紧(螺丝) f i x t u r e夹具(治具) p a l l e t栈板b a r c o d e条形码barcode scanner条形码扫描仪f u s e t o g e t h e r熔合f u s e m a c h i n e热熔机r e p a i r修理o p e r a t o r作业员Q C品管s u p e r v i s o r课长M E制造工程师M T制造生技cosmetic inspect外观检查inner parts inspect内部检查t h u m b s c r e w大头螺丝l b s.i n c h镑、英寸E M I g a s k e t导电条f r o n t p l a t e前板r e a r p l a t e后板c h a s s i s|'∫s i|基座b e z e l p a n e l面板power button电源按键r e s e t b u t t o n重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts 冲件p l a s t i c p a r t s塑料件S O P制造作业程序material check list物料检查表w o r k c e l l工作间t r o l l e y台车c a r t o n纸箱s u b-l i n e支线l e f t f o r k叉车p e r s o n n e l r e s o u r c ed e p a r t m e n t人力资源部production department生产部门planning department企划部Q C S e c t i o n品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener 整平机punching machine 冲床r o b o t机械手hydraulic machine油压机l a t h e车床|刨床p l a n e r|'p l e i n m i l l e r铣床g r i n d e r磨床d r i l l e r钻床l i n e a r c u t t i n g线切割electrical sparkle电火花w e l d e r电焊机staker=reviting machine铆合机p o s i t i o n职务p r e s i d e n t董事长general manager总经理special assistant manager 特助f a c t o r y d i r e c t o r厂长department director部长deputy manager |'depjuti|=v i c e m a n a g e r副理section supervisor课长deputy section supervisor=vice section superisor副课长group leader/supervisor组长l i n e s u p e r v i s o r线长assistant manager助理to move, to carry, toh a n d l e搬运be put in storage入库p a c k p a c k i n g包装t o a p p l y o i l擦油t o f i l e b u r r锉毛刺f i n a l i n s p e c t i o n终检to connect material接料to reverse material 翻料w e t s t a t i o n沾湿台T i a n a天那水c l e a n i n g c l o t h抹布t o l o a d m a t e r i a l上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废s c r a p e..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturingp r o c e d u r e制程不良oxidation |' n|氧化«ksi'deis c r a t c h刮伤d e n t s压痕defective upsiding down抽芽不良defective to staking铆合不良m p|镶块Ùe m b e d e d l u m p|i n'b e d||l feeding is not in place送料不到位s t am pin g-m is s in g漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件f o r k l i f t叉车trailer=long vehicle拖板车c o m p o u nd d i e合模d ie l o c k e r锁模器pressure plate=plate pinch 压板b o l t螺栓name of a department部门名称administration/general a f f a i r s d e p t总务部automatic screwdriver电动启子thickness gauge厚薄规g a u g e(o r j i g)治具p o w e r w i r e电源线b u z z l e蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座p e d a l踩踏板s t o p p e r阻挡器f l o w b o a r d流水板hydraulic handjack油压板车f o r k l i f t叉车p a l l e t栈板g l o v e(s)手套glove(s) with exposedf i ng e r s割手套t h u m b大拇指f o r e f i ng e r食指m i d f i n g e r中指r i n g f i n g e r无名指l i t t l e f i n g e r小指b a n d-a i d创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头s w e e p e r扫把m o p拖把vaccum cleaner吸尘器r a g抹布garbage container灰箕g a r b a g e c a n垃圾箱g a r b a g e b a g垃圾袋c h a i n链条j a c k升降机pro du c ti on lin e流水线c h a i n链条槽m a g n e t i z e r加磁器l a m p h o l d e r灯架to mo p th e f l o or拖地to clean the floor扫地to clean a table擦桌子a i r p i p e气管p a c k a g i n g t o o l打包机p a c k a g i n g打包m i s s i n g p a r t漏件w r o n g p a r t错件excessive defects过多的缺陷critical defect极严重缺陷m a j o r d e f e c t主要缺陷m i n o r d e f e c t次要缺陷not up to standard不合规格dimension/size is a little b i g g e r尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery s c r e w h e a d螺丝滑头s l i p p e d screwhead/shippery screw t h r e a d滑手s p e c k l e斑点mildewed=moldy=mouldy发霉r u s t生锈d e f o r m a t i o n变形burr(金属)flash(塑件)毛边p o o r s t a k i n g铆合不良excesssive gap间隙过大g r e a s e/o i l s t a i n s油污i n c l u s i o n杂质p a i n tin g p e e l of f脏污shrinking/shrinkage缩水m i x e d c o l o r杂色s c r a t c h划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱pain tin g make-up补漆d i s c o l o r a t i o n羿色w a t e r s p o t s水渍p o l i s h i n g/s u r f a c ep r o c e s s i n g表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位s a f e t y安全q u a l i t y品质delivery deadline交货期c o s t成本e n g i n e e r i n g工程d ie r e p a i r模修e n t e r p r i s e p l a n=e n t e r p r i s e e x p a n s i o np r o j e c t s企划Q C品管d ie w o r k e r模工production, to produce生产e q u i p m e n t设备t o s t a r t a p r e s s开机stop/switch off a press关机c l a s s i f i c a t i o n整理r e g u l a t i o n整顿c l e a n n e s s清扫c o n s e r v a t i o n清洁c u l t u r e教养q u a l i f i ed p r o d u c t s, up-to-grade products良品defective products, not up-to-grade products不良品w a s t e废料b o a r d看板f e e d e r送料机s l i d i n g r a c k滑料架defective product box不良品箱d i e c h a n g e换模t o f i x a d i e装模to take apart a die拆模t o r e p a i r a d i e修模p a c k i n g m a t e r i a l包材b a s k e t蝴蝶竺p l a s t i c b a s k e t胶筐isolating plate baffle plate;b a r r ic ad e隔板c a r t o n b o x纸箱to pull and stretch拉深to put material in place, tocut material, to input落料t o i m p o s e l i n e s压线to compress, compressing压缩c h a r a c t e rd i e字模t o f e e d,f e e d i n g送料t r a n s p o r t a t i o n运输(be)qualfied, up to grade合格not u p to grade, notq u a l i f i e d不合格material change, stockc h a n g e材料变更feature change 特性变更e v a l u a t i o n评估p r e p a r e f o r,m a k epreparations f or 准备p a r a m e t e r s参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量s t e e l p l a t e钢板r o l l m a t e r i a l卷料manufacture procedure制程operation procedure作业流程to revise, modi fy修订t o s w i t c h o v e r t o,switch---to throw--overs w i t c h i n g o v e r切换e n g i n e e r i n g,p r o j e c td i f f i c u l t y工程瓶颈s t a g e d i e工程模a u t o m a t i o n自动化to stake, staking, reviting 铆合add lubricating oil加润滑油s h u t d i e架模shut height of a die架模高度analog-mode device类模器d i e l i f t e r举模器a r g o n w e l d i n g氩焊vocabulary for stamping 冲压常词汇s t a m p i n g,p r e s s冲压punch press, dieing out p r e s s冲床uncoiler & strainghtener整平机f e e d e r送料机rack, shelf, stack料架c y l i n d e r油缸r o b o t机械手t a k e r取料机c o n v e y e r b e l t输送带transmission rack输送架t o p s t o p上死点b o t t o m s t o p下死点o n e s t r o k e一行程i n c h寸动to continue, cont.连动t o g r i p(m a t e r i a l)吸料location lump, locatingpiece, block stop 定位块r e s e t复位s m o o t h l y顺利d e n t压痕s c r a t c h刮伤d e f o r m a t i o n变形f i l i ng s铁削t o d r a w h o l e s抽孔inquiry, search for查寻to stock, storage, in stock库存r e c e i v e领取approval examine andv e r i f y审核processing, to process加工delivery, to deliver 交货to return delivenry to. tosend delinery back to retrno f g o o d s退货r e g i s t r a t i o n登记registration card登记卡t o c o n t r o l管制to put forward and hand in提报s a f e s t o c k安全库存acceptance = receive验收t o n o t i c e通知a p p l i c a t i o n f o r m f o rp u r c h a s e请购单consume, consumption消耗t o f i l l i n填写a b r a s i o n磨损reverse angle = chamfer倒角c h a r a c t e rd i e字模to collect, to gather收集f a i l u r e,t r o u b l e故障s t a t i s t i c s统计demand and supply需求c a re e r c a r d履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate 移走模板easily damaged parts易损件s t a n d a r d p a r t s标准件breaking.(be)broken,(be)c r a c k e d断裂t o l u b r i c a t e润滑common vocabulary for die engineering模具工程常用词汇d i e模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow(-o n)d i e连续模c o m p o u nd d i e复合模p u n c h e d h o l e冲孔p a n e l b o a r d镶块to cutedges=side cut=sides c r a p切边t o b e n d i n g折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边t o s t a k e铆合designing, to design设计design modification设计变化d ie b l o c k模块f o l d e d b l o c k折弯块s l i d i n g b l o c k滑块l o c a t i o n p i n定位销l i f t i n g p i n顶料销die plate, front board模板p a d d i n g b l o c k垫块s t e p p i n g b a r垫条u ppe r di e bas e上模座l o w e r d ie b a s e下模座upper supporting blank上承板upper padding plate blank上垫板s p a r e d i e s模具备品s p r i n g弹簧b o l t螺栓document folder活页夹f i l e f o l d e r资料夹to put file in order整理资料spare tools location手工备品仓f i r s t c o u n t初盘人f i r s t c h e c k初盘复棹人s e c o n d c o u n t复盘人second check复盘复核人e q u i p m e n t设备w a s t e m a t e r i a l s废料work in progress product 在制品casing = containerazation 装箱q u a n t i t y o f ph y si c a l invetory second count 复盘点数量quantity of customs count 会计师盘,点数量t h e f i r s t p a g e第一联f i l e d b y a c c o u n t i n g department for reference 会计部存查e n d-u s e r/u s i n g unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表b i l l n a m e单据名称This sheet and physicalinventory list will be sentto accounting departmenttogether (Those of NHKwill be sent to financiald e p a r t m e n t)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status recordso f y e a r-e n d p h y s i c a linventory List and physicalinventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号p l a t e电镀m o l d成型material for engineeringmold testing工程试模材料not included in physicali n v e n t o r y不列入盘点s a m p l e样品incoming material to bei n s p e c t e d进货待验d e s c r i p t i o n品名s te e l/ro l le d s te e l钢材material statistics sheet物料统计明细表meeting minutes会议记录m e e t i n g t y p e会别distribution department分发单位l o c a t i o n地点c h a i r m a n主席present members出席人员s u b j e c t主题c o n c l u s i o n结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production s c h e d u l e s h e e t P C E组装厂生产排配表m o d e l机钟w o r k o r d e r工令r e v i s i o n版次r e m a r k备注p r o d u c t i o n c o n t r o l c o n f i r m a t i o n生产确认c h e c k e d b y初审a p p r o v e d b y核准d e p a r t m e n t部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞t o b e i n s p e c t e d o rr e w o r k e d待验或重工t o t a l合计cause description原因说明part number/ P/N 料号t y p e形态i t e m/g r o u p/c l a s s类别q u a l i t y品质p r e p a r e d b y制表n o t e s说明y e a r-e n d p h y s i c a li n v e n t o r y d i f f e r e n c ea n a l y s i s s h e e t年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析r a w m a t e r i a l s原料m a t e r i a l s物料f i n i s h e d p r o d u c t成品semi-finished product半成品packing materials包材good product/acceptedg o o d s/a c c e p t e dp a r t s/g o o d p a r t s良品d e f e c t i v eproduct/non-good parts不良品dis pos ed goods处理品w a r e h o u s e/h u b仓库on way location在途仓oversea location海外仓s p a r e p a r t s p h y s i c a linventory list备品盘点清单spare molds location模具备品仓s k i d/p a l l e t栈板t o x m a c h i n e自铆机w i r e E D M线割E D M放电机c o i l s t o c k卷料s h e e t s t o c k片料t o l e r a n c e工差s c o r e=g r o o v e压线c a m b l o c k滑块p i l o t导正筒t r i m剪外边p i e r c e剪内边d r a g f o r m压锻差pocket for the punch head 挂钩槽s l u g h o l e废料孔f e a t u r e d i e公母模e x p a n s i o n d w g展开图r a d i u s半径s h i m(w e d g e)楔子torch-flame cut火焰切割s e t s c r e w止付螺丝f o r m b l o c k折刀s t o p p i n定位销round pierce punch=dieb u t t o n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角a c t i v e p l a t e活动板b a f f l e p l a t e挡块c o v e r p l a t e盖板m a l e d i e公模f e m a l e d i e母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板b u s h i n g b l oc k衬套i n s e r t入块c l u b c a r高尔夫球车c a p a b i l i t y能力p a r a m e t e r参数f a c t o r系数p h o s p h a t e皮膜化成v i s c o s i t y涂料粘度a l k a l i d i p p i n g脱脂main manifold主集流脉b e z e l斜视规b l a n k i n g穿落模d e j e c t i n g顶固模demagnetization去磁;消磁high-speed transmission高速传递h e a t d i s s i p a t i o n热传r a c k上料d e g r e a s e脱脂r i n s e水洗a l k a l i n e e t c h龄咬d e s m u t剥黑膜D.I.r i n s e纯水次C h r o m a t e铬酸处理A n o d i z e阳性处理s e a l封孔r e v i s i o n版次p a r t n u m b e r/P/N料号g o o d p r o d u c t s良品scraped products报放心品defective products不良品f in ish ed products成品disposed products处理品b a r c o d e条形码f l o w c h a r t流程窗体a s s e m b l y组装s t a m p i n g冲压m o l d i n g成型spare parts=buffer备品c o o r d i n a t e坐标dismantle the die折模auxiliary fuction辅助功能p o l y-l i n e多义线h e a t e r b a n d加热片t h e r m o c o u p l e热电偶s a n d b l a s t i n g喷沙g r i t砂砾derusting machine除锈机d e g a t e打浇口d r y e r烘干机i n d u c t i o n感应i n d u c t i o n l i g h t感应光response=reaction=interac t i o n感应r a m连杆e d g ef i n d e r巡边器c o n c a v e凸c o n v e x凹s h o r t射料不足n i c k缺口s p e c k瑕疪s h i n e亮班s p l a y银纹g a s m a r k焦痕d e l a m i n a t i o n起鳞c o ld s l u g冷块b l u s h导色g o u g e沟槽;凿槽s a t i n t e x t u r e段面咬花w i t n e s s l i n e证示线p a t e n t专利g r i t沙砾granule=peuet=grain细粒g r i t m a k e r抽粒机c u s h i o n缓冲m a g n a l i u m镁铝合金m a g n e s i u m镁金m e t a l p l a t e钣金l a t h e车m i l l锉p l a n e刨g r i n d磨d r i l l铝b o r i n g镗b l i n s t e r气泡f i l l e t镶;嵌边through-hole form通孔形式voller pin formality滚针形式c a md r i ve r铡楔s h a n k摸柄c r a n k s h a f t曲柄轴augular offset角度偏差v e l o c i t y速度production tempo生产进度现状t o r q u e扭矩spline=the multiple keys花键q u e n c h i n g淬火t e m p e r i n g回火a n n e a l i n g退火c a r b o n i z a t i o n碳化a l l o y合金tungsten high speed steel 钨高速的moly high speed steel钼高速的organic solvent有机溶剂b r a c k e t小磁导l i a i s o n联络单v o l a t i l e挥发性r e s i s t a n c e电阻i o n离子t i t r a t o r滴定仪b e ac o n警示灯c o o l a n t冷却液c r u s h e r破碎机模具工程类p l a i n d i e简易模p i e r c e d i e冲孔模f o r m i ng d i e成型模progress ive die连续模g a n g d i e s复合模s h e a r i n g d i e剪边模r i v e t i n g d i e铆合模p i e r c e冲孔forming成型(抽凸,冲凸)d r a w h o l e抽孔b e n d i n g折弯t r i m切边e m b o s s凸点d o m e凸圆s e m i-s h e a r i n g半剪s t a m p m a r k冲记号d e b u r r o r c o i n压毛边punch riveting冲压铆合s i d e s t r e t c h侧冲压平r e e l s t r e t c h卷圆压平g r o o v e压线b l a n k i n g下料stamp letter冲字(料号)s h e a r i n g剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类e x t e n s i o n d w g展开图p r o c e d u r e d w g工程图die structure dwg模具结构图m a t e r i a l材质material thickness料片厚度f a c t o r系数u p w a r d向上d o w n w a r d向下press specification冲床规格die height range适用模高d i e h e i g h t闭模高度b u r r毛边g a p间隙w e i g h t重量t o t a l w t.总重量p u n c h w t.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉d o w e l p i n固定销c o i l s p r i n g弹簧l i f t e r p i n顶料销eq-height sleeves=spool等高套筒p i n销lifter guide pin浮升导料销g u i d e p i n导正销w i r e s p r i n g圆线弹簧outer guiding post外导柱s t o p s c r e w止付螺丝l o c a t e d p i n定位销o u t e r b u s h外导套模板类top plate上托板（顶板）t o p b l o c k上垫脚p u n c h s e t上模座p u n c h p a d上垫板p u n c h h o l d e r上夹板s t r i p p e r p a d脱料背板u p s t r i p p e r上脱料板m a l e d i e公模(凸模)f e a t u r e d i e公母模f e m a l e d i e母模(凹模)u p p e r p l a t e上模板l o w e r p l a t e下模板d ie p a d下垫板d ie h o l d e r下夹板d ie s e t下模座b o t t o m b l oc k下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类p u n c h冲头i n s e r t入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子r o u n d p u n c h圆冲子special shape punch异形冲子b e n d i n g b l oc k折刀r o l l e r滚轴b a f f l e p l a t e挡块l o c a t e d b l o c k定位块s u p p o r t i n g b l o c k f o rl o c a t i o n定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = s t i n g e r加强筋冲子ribb on pu n ch压筋冲子reel-stretch punch卷圆压平冲子g u i d e p l a t e定位板s l i d i n g b l o c k滑块sliding dowel block滑块固定块a c t i v e p l a t e活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板s p r i n g b o x弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板b u s h i n g b o l c k衬套c o v e r p l a t e盖板g u i d e p a d导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具c a v i t y型控母模c o r e模心公模t a p e r锥拔l e a t h e r c l o a k仿皮革s h i v e r饰纹f l o w m a r k流痕w e l d i n g m a r k溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝s t r i p e r p l a t e脱料板p i s t o n活塞c y l i nde r汽缸套c h i p细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）w e l l t y p e蓄料井insulated runner绝缘浇道方式h o t r u n n e r热浇道r u n n e r p l a t浇道模块v a l v e g a t e阀门浇口band heater环带状的电热器s p i n d l e阀针s p e a r h e a d刨尖头s l a g w e l l冷料井c o ld s l a g冷料渣a i r v e n t排气道h=0.02~0.05m m w=3.2m m L=3~5m m w e l d i n g l i n e熔合痕e j e c t p i n顶出针k n o c k p i n顶出销return pin回位销反顶针s l e a v e套筒s t r i p p e r p l a t e脱料板i n s e r t c o r e放置入子runner stripper plate浇道脱料板g u i d e p i n导销eject rod (bar)（成型机）顶业捧s u b z e r o深冷处理th re e pl ate三极式模具runner system浇道系统s t r e s s c r a c k应力电裂o r i e n t a t i o n定向sprue gate射料浇口，直浇口n o z z l e射嘴sprue lock pin料头钩销(拉料杆)s l a g w e l l冷料井s i d e g a t e侧浇口e d g e g a t e侧缘浇口t a b g a t e搭接浇口f i l mg a t e薄膜浇口f l a s hg a t e闸门浇口s l i t g a t e缝隙浇口f a ng a t e扇形浇口d i s h g a t e因盘形浇口H=F=1/2t~1/5tT=2.5~3.5m mdiaphragm gate隔膜浇口r i n g g a t e环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口p i n g a t e针点浇口Φ0.8~1.0m mR u n n e r l e s s无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式s p r u e浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control终点质量管理人员IPQC in process qualitycontrol 制程中的质量管理人员OQC output quality control最终出货质量管理人员IQ C in comin g qu al i tycontrol 进料质量管理人员TQC total quality control全面质量管理P O C p a s s a g e q u a l i t yc o n t r o l段检人员QA quality assurance 质量保证人员O Q A o u t p u t q u a l i t yassurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数S S Q A s t a n d a r d i z e d supplier quality 合格供货商品质评估OOBA out of box audit 开箱检查Q F D qu a l i ty f u n c ti o ndeployment 品质机能展开F M E A f a i l u r e m o d e leffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective actionr e q u e s t改正行动要求corrective action report改正行动报告F Q C运作类AQL Acceptable QualityLevel 运作类允收品质水准S/S Sample size 抽样检验样本大小A C C A c c e p t允收R E E R e j e c t拒收C R C r i t i c a l极严重的M A J M a j o r主要的M I N M i n o r轻微的A O Q A v e r a ge O u tp u tQ u a l i t y平均出厂品质AOQL Average OutputQuality Level 平均出厂品质Q/R/SQuality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard军用标准S I-S IV Special I-SpecialI V特殊抽样水准等级P/N Part Number 料号L/N L ot N umbe r 特采AOD Accept On Deviation特采UAI Use As It 首件检查报告FPIR First Piece InspectionR e p o r t百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process C o n t r o l统计制程管制SQC Statistical Quality C o n t r o l统计质量管理R R a n g e全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Max imu m 最大值M I N M i n i m u m最小值G R R G a u g e Reproducibility&Repeatabil ity 量具之再制性及重测性判断量可靠与否D I M D i m e n s i o n尺寸D I A D i a m e t e r直径FREQ Fre quen cy频率N N u m b e r样品数其它品质术语类QCC Quality Control Circle品质圈QIT Quality ImprovementT e a m品质改善小组P D C A P l an D o C h e c kAction 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement品质改善QP Quality Policy 目标方针T Q M T o t a l Q u a l i t yManagement 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level最低品质水准RMA Return Material Audit退料认可QAN Quality AmelionrateN o t i c e品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7Q C T o o l s7Q u a l i t yControll Tools 品管七大手法通用之件类ECN Engineering ChangeNotes 工程变更通知(供货商)ECO Engineering ChangeOrder 工程改动要求(客户)P C N P r o c e s s C h a n g eN o t i c e工序改动通知PMP Product ManagementP l a n生产管制计划S I P S p e c i f i c a t i o n I nP r o c e s s制程检验规格SOP Standard OperationProcedure 制造作业规范IS Inspection Specification成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格D W G D r a w i n g图面系统文件类QC Quality System 品质系统E S E n g i n e e r i n g Standarization 工程标准CGOO China General PCE 龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C C h i n a中国大陆A A s s e m b l y组装(厂) S S t a m p i n g冲压(厂) P P a i n t i n g烤漆(厂) I I n t e l英特尔公司T T A I W A N台湾I W S I n t e r n a t i o n a l Workman Standard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification一般规格CMCS C-China M-ManufactC-Compaq S-StampingCompaq产品在龙华冲压厂制造作业规范C Q C A Q-Q u a l i t yA-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制P P C P r o d u c t i o n P l a nC o n t r o l生产计划控制MC Material Control 物料控制M E M a n a f a c t u r eEngineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A P e r s o n a l&Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 质量管理(课)PD Product Department生产部L A B L a b r a t r y实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P P a i n t i n g烤漆(厂) A Ass se mbly组装(厂) S S t a m p i n g冲压(厂) 生产类PCS Pieces 个(根,块等) P R S P a i r s双(对等) C T N C a r t o n卡通箱P A L P a l l e t/s k i d栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N L ot N umbe r 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal ComputerEnclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central ProcessingU n i t中央处理器S E C C S E C C`电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong中国大陆PRC People's Republic ofC h i n a中国大陆U.S.A the United States ofAmerica 美国尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用Q T Y Q u a n t i t y数量V S以及R E V R e v i s i o n版本JIT Just In Time 零库存I/O Input/Output 输入/输出O K O k好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许E S D E l e c t r y-s t a t i cD i s c h a r g e静电排放5S 希腊语整理,整顿,清扫,清洁,教养A T I N A t t e n t i o n知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认C H K C h e c k确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器C A V C a v i t y模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装M A T'S M a t e r i a l材料IC Integrated Circuit 集成电路T/P True Position 真位度T Y P T y p e类型WDR Weekly Delivery Requitement 周出货需求CT Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3 CComputer,Commumcation,Consumer electronic's 消费性电子5W I HWhen,Where,Who,What,W h y,H o w t o5MMan,Machine,Material,Meth o d,M e a s u r e m e n t4M I HMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strate gy Qu alityAssurance 策略品质保证D Q A D e s i g h Q u a l i t yAssurance 设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and serviceQuality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionI n s p e c t高磁测试FMI Frequency ModulatimI n s p e c t高频测试B/M Boar/Molding(flatc a b l e)C/P C o n n e c t o r o f P CA/P A s s e m b l yS PS S wi tch i n g p o we rs u p p l y电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact Disk LCD Liquid Crystal Display CAD Computer AID Design C A M C o m p u t e r A I D M a n u f a c t u r i n g C A E C o m p u t e r A I D E n g i n e e r i n g ABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruar y M e t o l l O x i d e Semiconductor 互补金属氧化物半导体P D A P e r s o n a l D i g i t a l Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构M C A M i c r o C h a n n e l Architecture 微信道结构EISA Extended IndustryStandard Architecture 扩充的工业标准结构S I M M S i n g l e i n-l i n ememory module 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode发光二级管F M E A F a i l u r e M o d eEffectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C F l a t C a l l e排线PCB Printed Circuit Board印刷电路板CAR Correction ActionR e p o r t改善报告N G N o t G o o d不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material RequiremcntP l a n n i n g物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺D/C D r a w i n g C h an g eP/P Plans & ProceduneE M I E l e c t r i c a l-M u s i cIn dus try电子音乐工业RFI Read Frequency Input读频输入MMC Maximum MaterialC o n d i t i o nMMS Maximum MaterialS i z eL M C L e a s t M a t e r i a lC o n d i t i o nLMS Least Material Size。
机械生产常用专业英语单词
机构设计及生产常用专业英语单词组装、冲压、喷漆等专业词汇assembly line 组装线layout 布置图conveyer 流水线物料板rivet table 拉钉机rivet gun 拉钉枪screw driver 起子electric screw river 电动起子pneumatic screw driver 气动起子work table 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机riveting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特助factory director 厂长department director 部长deputy manager/vice manager 副经理section supervisor 课长deputy/ vice section supervisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理经理to move/to carry/to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped 报废scrape 刮削deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure 制程不良oxidation 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓部门名称(name of a department )administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzer 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器flow board 流水板hydraulic hand-jack 油压板车forklift 叉车pallet 栈板glove(s) 手套glove(s) with exposed fingers 割手套thumb 大拇指forefinger 食指mid-finger 中指ring finger 无名指little finger 小指band-aid 创可贴industrial alcohol 工业酒精alcohol container 沾湿台head of screwdriver 起子头sweeper 扫把mop 拖把vacuum cleaner 吸尘器rag 抹布garbage container 灰箕garbage can 垃圾箱garbage bag 垃圾袋chain 链条jack 升降机production line 流水线chain slot 链条槽magnetizer 加磁器lamp holder 灯架to mop the floor 拖地to clean the floor 扫地to clean a table 擦桌子air pipe 气管packaging tool 打包机packaging 打包missing part 漏件wrong part 错件excessive defects 过多的缺陷critical defect 极严重缺陷major defect 主要缺陷minor defect 次要缺陷not up to standard 不合规格dimension/size is a little bigger 尺寸偏大(小) cosmetic defect 外观不良slipped/slippery screw head 螺丝滑头slipped/slippery screw thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉rust 生锈deformation 变形burr(金属)flash (塑件)毛边poor staking 铆合不良excessive gap 间隙过大grease/oil stains 油污inclusion 杂质painting peel off 脏污shrinking/shrinkage 缩水mixed color 杂色scratch 划伤poor processing 制程不良poor incoming part 事件不良fold of packaging belt 打包带折皱painting make-up 补漆discoloration 羿色water spots 水渍polishing/surface processing 表面处理exposed metal/bare metal 金属裸露lack of painting 烤漆不到位safety 安全quality 品质delivery deadline 交货期cost 成本engineering 工程die repair 模修enterprise plan/expansion projects 企划QC 品管die worker 模工production, to produce 生产equipment 设备to start a press 开机stop/switch off a press 关机classification 整理regulation 整顿cleanness 清扫conservation 清洁culture 教养qualified/up-to-grade products 良品defective/not up-to-grade products 不良品waste 废料board 看板feeder 送料机sliding rack 滑料架defective product box 不良品箱die change 换模to fix a die 装模to take apart a die 拆模to repair a die 修模packing material 包材basket 蝴蝶竺plastic basket 胶筐isolating/baffle plate; barricade 隔板carton box 纸箱to pull and stretch 拉深to cut material 落料to impose lines 压线to compress, compressing 压缩character die 字模to feed, feeding 送料transportation 运输(be)qualified, up to grade 合格not up to grade, not qualified 不合格material change, stock change 材料变更feature change 特性变更evaluation 评估prepare for, make preparations for 准备parameters 参数rotating speed, revolution 转速manufacture management 制造管理abnormal handling 异常处理production unit 生产单位lots of production 生产批量steel plate 钢板roll material 卷料manufacture procedure 制程operation procedure 作业流程to revise, modify 修订to switch over to 切换engineering, project difficulty 工程瓶颈stage die 工程模automation 自动化to stake/staking/riveting 铆合add lubricating oil 加润滑油shut die 架模shut height of a die 架模高度analog-mode device 类模器die lifter 举模器argon welding 氩焊冲压常词汇vocabulary for stampingstamping/press 冲压punch press/dieing out press 冲床feeder 送料机rack/shelf/stack 料架cylinder 油缸robot 机械手taker 取料机conveyer belt 输送带transmission rack 输送架top stop 上死点bottom stop 下死点one stroke 一行程inch 寸动to continue/cont. 连动to grip(material) 吸料location lump/locating piece/block stop 定位块reset 复位smoothly 顺利dent 压痕scratch 刮伤deformation 变形filings 铁削to draw holes 抽孔inquiry/search for 查寻to stock/storage/in stock 库存receive 领取approval examine and verify 审核processing/to process 加工delivery/to deliver 交货to return delivery to/to send delivery back/to return of goods 退货registration 登记registration card 登记卡to control 管制to put forward and hand in 提报safe stock 安全库存acceptance /receive 验收to notice 通知application form for purchase 请购单consume/consumption 消耗to fill in 填写abrasion 磨损reverse angle /chamfer 倒角character die 字模to collect/to gather 收集failure/trouble 故障statistics 统计demand and supply 需求career card 履历卡to take apart a die 卸下模具to load a die 装上模具to tight a bolt 拧紧螺栓to looser a bolt 拧松螺栓to move away a die plate 移走模板easily damaged parts 易损件standard parts 标准件breaking/(be)broken/(be)cracked 断裂to lubricate 润滑模具工程常用词汇(common vocabulary for die engineering)die 模具figure file/chart file 图档cutting die/blanking die 冲裁模progressive die/follow (-on)die 连续模compound die 复合模punched hole 冲孔panel board 镶块to cut edges/side cut/side scrap 切边to bending 折弯to pull, to stretch 拉伸Line stretching/line pulling 线拉伸Engraving/to engrave 刻印upsiding down edges 翻边to stake 铆合designing/ to design 设计design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate/ front board 模板padding block 垫块stepping bar 垫条upper die base 上模座lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓document folder 文件夹file folder 资料夹to put file in order 整理资料spare tools location 手工备品仓first count 初盘人first check 初盘复棹人second count 复盘人second check 复盘复核人equipment 设备waste materials 废料work in progress product 在制品casing/containerization 装箱quantity of physical inventory second count复盘点数量quantity of customs count 会计师盘点数量the first page 第一联filed by accounting department for reference会计部存查end-user/using unit(department) 使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name 单据名称physical inventory list 盘点清册accounting department 会计部financial department 财会部physical inventory card 盘点卡blank and waste sheet NO. 空白与作废单号plate 电镀mold 成型material for engineering mold testing 工程试模材料not included in physical inventory 不列入盘点sample 样品incoming material to be inspected 进货待验description 品名steel/rolled steel 钢材material statistics sheet 物料统计明细表meeting minutes 会议记录meeting type 会别distribution department 分发单位location 地点chairman 主席present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department 负责单位pre-fixed finishing date 预定完成日approved by 核准checked by 审核prepared by 承办PCE assembly production schedule sheetPCE组装厂生产排配表Model 机种work order 工令revision 版次remark 备注production control confirmation 生产确认checked by 初审approved by 核准department 部门stock age analysis sheet 库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked 待验或重工total 合计cause description 原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质prepared by 制表notes 说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 原因分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料sheet stock 片料tolerance 公差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head 挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge) 楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套club car 高尔夫球车capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkali dipping 脱脂main manifold 主集流脉bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁，消磁high-speed transmission 高速传递heat dissipation 热传递rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬Chromate 铬酸处理Anodize 阳性处理Seal 封孔Revision 版次part number/P/N 料号scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 坐标dismantle the die 折模auxiliary function 辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口speck 瑕疵shine 亮班splay 银纹gas mark 焦痕guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模) upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板) outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件) deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套cover plate 盖板guide pad 导料块塑件&模具相关英文compression molding 压缩成型flash mold 溢流式模具split mold 分割式模具cavity 型腔/母模core 模心/公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具encapsulation molding 射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleeve 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar) （成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口/直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口submarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道sprue less 无射料管方式long nozzle 延长喷嘴方式sprue 浇口/溶渣品质人员名称类QC quality control 品管员FQC final quality control 终点品管员IPQC in process quality control 制程中的品管员OQC output quality control 最终出货品管员IQC incoming quality control 进料品管员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽检样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 轻微的AOQ Average Output Quality 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility & Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action计划/执行/检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Ameliorate Notice 品质改善活动ADM Absolute Dimension Measurement全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Control Tools品管七大手法通用件类ECN Engineering Change Notes 工程变更通知ECO Engineering Change Order 工程改动要求PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standardization 工程标准H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司IWS International Workman Standard工艺标准ISO International Standard Organization国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manufacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Assembly 组装(厂)S Stamping 冲压(厂)生产类R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility & Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action计划/执行/检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Ameliorate Notice 品质改善活动ADM Absolute Dimension Measurement全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Control Tools品管七大手法通用件类ECN Engineering Change Notes 工程变更通知ECO Engineering Change Order 工程改动要求PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standardization 工程标准H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司IWS International Workman Standard工艺标准ISO International Standard Organization国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manufacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部) QA Quality Assurance 品质保证(处) QC Quality Control 品质管制(课) PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Assembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等) PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC 电解片SGCC 热浸镀锌材料PRC People's Republic of China中国大陆A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD electricity-static Discharge 静电排放ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requirement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer, Communication, Consumer electronics消费性电子5WIH When, Where, Who, What, Why, How to5M Man, Machine, Material, Method, Measurement 4MIH Man, Material, Money, Method, Time人力,物力财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Design Quality Assurance设计品质保证MQA Manufacture Quality Assurance制造品质保证SSQA Sales and service Quality Assurance销售及服务品质保证LRR Lot Reject Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblyPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system先进的基本输入/输出系统CMOS Complementary Metal Oxide Semiconductor互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry Standard Architecture扩充的工业标准结构SIMM Single in-line memory module单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectiveness失效模式分析W/H Wire Harness 金属线束集组件F/C Flat Cable 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requirement Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offset bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模portable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nipple 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶针lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止销straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep template 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机CNC milling machine CNC 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC 钻床NC grinding machine NC 磨床NC lathe NC 车床NC programming system NC 程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分千分尺interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一寸monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢。
机械专业术语
组装、冲压、喷漆等专业词汇Assembly line组装线アセンブリーLayout布置图レイアウトConveyer流水线物料板、输送带Rivet table拉钉机リベット・テーブルRivet gun拉钉枪リベット・ガンScrew driver起子スクリュー・ドライバーElectric screw driver电动起子エレクトリックPneumatic screw driver气动起子ニューマチックworktable 工作桌ワークテーブルOOBA开箱检查fit together组装在一起フィット・ツゲザfasten锁紧(螺丝) ファスナー（fastener）fixture 夹具(治具) フイクスチャーpallet栈板パレットbarcode条码バー・コードbarcode scanner条码扫描器バー・コードスキャナーfuse together熔合ヒューズfuse machine热熔机マシンrepair修理リペアoperator作业员オペレーターQC品管supervisor 课长スーパーバイザーME制造工程师MT制造生技cosmetic inspect外观检查コスメチック・インスぺクトinner parts inspect内部检查イナー・パーツ・インスぺクトthumb screw大头螺丝サムスクリューlbs. inch镑、英寸インチEMI gasket导电条Gasket密封圈，垫圈ガスケットfront plate前板rear plate后板リア・プレートchassis 基座シャーシーbezel panel面板ベーザル・パネルpower button电源按键パワー・ボタンreset button重置键リセット・ボタンHi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键ボレテージsheet metal parts 冲件シーツplastic parts塑胶件ペラスチック・パーツSOP制造作业程序material check list物料检查表マテリアル・チェッキ（チッキ）work cell工作间ワーク・セルtrolley台车、电车トロリーcarton纸箱カートンsub-line支线、辅助线サブライーleft fork叉车レフト・フォークproduction department生产部门プロダクション・デパートメントplanning department企划部プラニングQC Section品管科セクションstamping factory冲压厂スタンピング・ファクトリーpainting factory烤漆厂ペインティングmolding factory成型厂モールディングcommon equipment常用设备コモン・イクイップメントuncoiler and straighte ner整平机アンコイラー・アンド・ストレートpunching machine 冲床パンチングrobot机械手ロボットhydraulic machine油压机、水压，液压ハイドロリックlathe车床ラスplaner刨床ペレーナーmiller铣床ミラーgrinder磨床、研磨机グラインダーdriller铣床ドララードラル（drill）linear cutting线切割リニア・カッティングelectrical sparkle电火花エレクトりカル・スパークル1welder电焊机ウエルダーstaker= riveting machine 铆合机リベッティングposition职务ボジションpresident董事长プレジデントgeneral manager总经理ジェネラル・マネージャーspecial assistant manager特助スペシャル・アシスタント・マネージfactory director厂长ファクトリー・ディレクターdepartment director部长デパートメント・ディレクターdeputy manager =vice manager副理デピューチ・マネージャーバイス・マネージャーsection supervisor课长セクション・スーパーバイザーdeputy section supervisor =vice section superisor 副课长デピューチ・セクション・スーパーバイザーバイス・セクション・スーパーバイザーgroup leader/supervisor组长グループ・リーダー/スーパーバイザーline supervisor线长ライン・スーパーバイザーassistant manager助理アシスタント・マネージto move, to carry, to handle搬运be put in storage入库ストーリッジpacking包装パッキングto apply oil擦油to file（锉刀）burr（垫圈，圆头挫）锉毛刺ファイル・バーfinal inspection终检ファイナル・インスペクションto connect material接料（connector 插头，接头）to reverse material 翻料リバースwet station沾湿台cleaning cloth抹布to load material上料ロード（装载）to unload material卸料to return material/stock to退料scrape d报废スクラップscrape ..v.刮;削deficient purchase来料不良デフィシット・パーチェスmanufacture procedure制程マニュファクチャー・プロシージャーdeficient manufacturing procedure制程不良oxidation 氧化オキシデーションscratch刮伤スクラッチdents压痕defective upsiding down抽芽不良デフェクティブdefective to staking铆合不良デフェクティブembedded lump镶块ランプfeeding is not in place送料不到位フィーディングstamping-missing漏冲スタンピング・ミッシングproduction capacity生产力ポロダクション・カパシティーeducation and training教育与训练proposal improvement提案改善プロポーザルspare parts=buffer备件スペア・パースバッファー缓冲forklift叉车フォーク・リフトtrailer=long vehicle拖板车トレーラー/ロング・ビークルcompound die合模コンパウンド・ダイdie locker锁模器ダイ・ロッカーpressure plate=plate pinch压板プレッシャー・プレート2bolt螺栓ボートname of a department部门名称administration/general affairs dept总务部アドミニストレーション/ジェネラルアッフェヤーautomatic screwdriver电动启子オートマチックthickness gauge厚薄规シックネス・ゲージgauge 量具power wire电源线buzzle蜂鸣器defective product label不良标签デフェクティブ・プロダクト・ラベルidentifying sheet list标示单アイデンティファイscrewdriver holder起子插座pedal踩踏板ペダルstopper阻挡器flow board流水板hydraulic handjack油压板车ハイドロリックハンド・ジャッキhandjackハンド・ジャッキ手动千斤顶forklift叉车フォーク・リフトpallet栈板パレットglove(s)手套グローブglove(s) with exposed fingers割手套thumb[θʌm]大拇指forefinger[‘fɔ:‘fiŋɡə]食指midfinger中指バンド・エイドring finger无名指little finger小指band-aid创可贴iudustrial alcohol[ˈælkəˈhɔl]工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop[mɔp]拖把vaccum cleaner吸尘器「'vækjuəm」rag 抹布garbage container灰箕ガーベッジ・コンテナーcontainer 集装箱コンテナーgarbage can垃圾箱カンgarbage bag垃圾袋バグchain链条チェーンjack升降机，千斤顶ジャッキproduction line流水线magnetizer加磁器lamp holder灯架ランプto mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管エア・パイプpackaging tool打包机packaging打包[‘pækidʒiŋ]missing part漏件wrong part错件excessive defect s过多的缺陷エクセッシブ・デフェクトcritical defect枀严重缺陷クリティカル・major defect主要缺陷メイジャー・minor defect次要缺陷マイナーnot up to standard不合规格スタンダードdimension/size is a little bigger尺寸偏大(小) ジメンションcosmetic defect外观不良コスメチック・slipped screwhead/slippery screw head螺丝滑头スリップslipped screwhead/shippery screw thread滑手speckle斑点スペックルmildewed=moldy=mouldy发霉rust生锈ラストdeformation变形ディフォメーションburr(金属)flash(塑件)毛边burr圆头锉バーpoor staking铆合不良パーア・excesssive gap间隙过大grease/oil stains油污グリース/オイル・ステインinclusion杂质インクルージョンpainting peel off剥落3shrinking/shrinkage缩水ピールmixed color杂色scratch划伤スクラッチpoor processing 制程不良ポロセッサーpoor incoming part事件不良fold of packaging belt打包带折皱フォールドpainting make-up补漆discoloration变色，污点ディスカラーwater spots水渍ウオーター・スポットpolishing/surface processing表面处理ポリッシュexposed metal/bare metal金属裸露エクスポーズド/ベアlack of painting烤漆不到位safety安全セーフティーquality品质クオリティーdelivery deadline交货期cost成本engineering工程エンジニアリングdie repair模修ダイ・リペアenterprise plan = enterprise expansion projects企划エンタープライズ・プラン=エンタープライズ・エクスパンション・プロジェクトEnterprise 企业，规划QC品管die worker模工production, to produce生产equipment设备＝設備せつびto start a press开机プレスstop/switch off a press关机classification整理クラシフィケーションregulation整顿、条例，调节レギュレーションcleanness清扫conservation清洁、维持，保护コンサーベーションculture教养カルチャーqualified [’kwɔlifaid]products, up-to-gradeproducts良品defective products, not up-to-grade products不良品waste废料ウイスboard看板ボードfeeder送料机フィードsliding rack滑料架スライディング・ラックdefective product box不良品箱die change 换模ダイ・チェンジto fix a die装模フィクスto take apart a die（拆开）拆模to repair a die修模packing material包材材料：ざいりょうbasket蝴蝶竺バイスケplastic basket胶筐isolating plate baffle[‘bæfl] plate; barricade[、bæri‘keid]隔板carton box纸箱to pull and stretch拉深drawingto put material in place, to cut material, to input落料to impose lines压线インポーズto compress, compressing压缩コンプレスcharacter die字模カラクターto feed, feeding送料トランスポーテーションtransportation运输トランスポーテーション(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估イバリュエーションprepare for, make preparations for 准备parameters参数パラメーターrotating speed, revolution转速回転速度manufacture management制造管理abnormal handling异常处理アブノーマルproduction unit生产单位lots of production生产批量steel plate钢板スチールroll material卷料ロールmanufacture procedure制程4operation procedure作业流程to revise, modify修订リバイズ修訂：しゅうていto switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油[‘lu:brikeitiŋ] shut die架模シャット・ダイshut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊[‘ɑ:ɡɔn]アルゴン・ウエルジング/ウエルディングvocabulary for stamping冲压常词汇stamping, press冲压スタンピング/プレスpunch press, dieing out press冲床押し抚き機.パンチプレスuncoiler & strainghtener整平机[ʌn‘kɔilə] feeder送料机フィードrack, shelf, stack料架ラック/シェルフ/スタックcylinder油缸シリンダーrobot机械手ロボットtaker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程[strəuk]inch寸动インチto continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位リセットsmoothly顺利dent压痕、凹痕scratch刮伤スクラッチdeformation变形デフォ－メーション/ディフォメーションfilings锉削ファイリングto draw holes抽孔inquiry, search for查寻[in‘kwaiəri]to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货納期：のうきto return delivery to.to send deliｖery back /to retrn of goods退货registration登记登録：とうろくregistration card登记卡[、redʒis‘treiʃən]to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收検収（けんしゅう）to notice通知（application form ）申请书for purchase请购单購入申請書しんせいしょconsume, consumption消耗to fill in填写abrasion磨损擦り減る：すりへる/摩耗：まもうreverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障こしょうstatistics统计統計：とうけいdemand and supply需求じゅようcareer card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓ボルトをきつく/しっかりと絞る「しぼる」きつい5to looseｎa bolt拧松螺栓ボルトを緩く絞る「しぼる」to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模ポログレッシブ・ダイcompound die复合模コンポーネントpunched hole冲孔パンチ・ホールpanel board镶块パネル・ボードto cutedges=side cut=side scrap切边to bending折弯ベンディングto pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化[，ɔdifi‘keiʃən]die block模块ダイ・ブロックfolded block折弯块フォールド・ブロックsliding block滑块スライディング・ブロックlocation pin定位销ロケーション・ピンlifting pin顶料销リフトdie plate, front board模板ダイ・プレート/フロント・ボードpadding block垫块パジング・ブロックstepping bar垫条ステッピング・バーupper die base上模座アッパー・ダイ・ベースlower die base下模座ローワー・ダイ・ベースupper supporting blank上承板アッパー・サポーティング・ブランクupper padding plate blank上垫板アッパー・パジング・ブロック・ブランクspare dies模具备品スペア・ダイザspring 弹簧スプリングbolt螺栓ボルトdocument folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复核人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical inveｎtory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表physical inventory实测库存量;实测物料量,实际盘存bill name单据名称This sheet and physical inventory list will be sent toaccountingdepartment together (Those of NHK will be sent tofinancialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical6inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名ディスクリプションsteel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产计划/进度表model机种work order工令revision版次リビションremark备注リマーくproduction control confirmation生产硭认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用[ə‘veiləbl]obsolete material良品已呆滞[‘ɔbsəli:t]废弃材料to be inspected or reworked待验或重工total合计トータルcause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysissheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料げんりょうmaterials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/goodparts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库倉庫：そうこon way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割7Electron Discharge Machining 放电加工EDM放电机coil stock卷料コイル・ストークsheet stock片料シート・ストークtolerance公差トレランスscore=groove压线cam block滑块カム・ブロックpilot导正筒パイロットtrim剪外边ツリム镶边，修边，剪边pierce剪内边ピアース穿孔，贯穿drag form压锻差ダラム・フォームpocket for the punch head挂钩槽punch head冲头slug hole废料孔feature die公母模[‘fi:tʃə]expansion dwg展开图radius半径shim(wedge)楔子[ʃim]torch-flame cut火焰切割[tɔ:tʃ] [fleim]set screw止付螺丝[skru:]form block折刀折刀成型模stop pin定位销round pierce punch=die button圆冲子[piəs] shape punch=die insert异形子压模嵌入件stock locater block定位块under cut=（scrap chopper碎边剪切机）清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆エア・クッションイジェクト・ロッドspring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力[，keipə‘biliti]parameter参数パラメーターfactor系数ファクターphosphate皮膜化成[‘fɔsfeit]フォースフェート磷酸盐viscosity涂料粘度[vis‘kɔsəti]alkalidipping脱脂degrease 脱脂[di:‘ɡri:z]main manifold主集流脉、主歧管bezel斜视规ベーぜルblanking穿落模ブランキングdejecting顶固模demagnetization去磁;消磁デマグネタイズhigh-speed transmission高速传递heat dissipation热传rack上料ラックrinse水洗リンスalkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理[‘krəumeit]Anodize阳性处理seal封孔、密封revision版次part number/P/N料号good products良品scraped products报放心品scraped报废defective products不良品finished products成品disposed products处理品barcode条码バー・コードflow chart流程表生産過程assembly组装アセンブリーstamping冲压スタンピングmolding成型モールディングspare parts=buffer备品coordinate座标表[kəu‘ɔ:dineit] 座標：ざひょうdismantle the die拆模ダイをばらす8auxiliary fuction辅助功能[ɔ:ɡ‘ziljəri]poly-line多义线heater band 加热片thermocouple热电偶[、θə:məu‘kʌpl]sand blasting喷沙处理grit 砂砾derusting machine除锈机錆取りさびdegate打浇口dryer烘干机乾燥机かんそうきinduction感应インダクションinduction light感应光インダクション・ライトresponse=reaction=interaction感应ram连杆ラムedge finder巡边器concave凹的くぼむconvex凸的, 凸面的膨れ上がる：ふくれあがるshort射料不足ショートnick缺口ニックspeckスぺークshine亮班シャインsplay 银纹[splei] 展开展開：てんかいgas mark焦痕delamination起鳞[di:、læmi‘neiʃən] 分层cold slug冷块注塑冷料コールド・blush 导色gouge沟槽;凿槽ゴージsatin texture段面咬花[‘sætin]witness line证示线patent专利パテントgrit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲[‘kuʃən]magnalium镁铝合金metal plate钣金メタル・プレートlathe车床旋盤：せんばんmill锉やすりplane刨削る：けずるgrind磨グラインドdrill铝ドリルboring镗、钻孔ボーリングblister气泡fillet镶;嵌边すめ込むthrough-hole form通孔形式voller pin formality滚针形式[fɔ:‘mæliti]cam driver铡楔凸轮传动器shank摸柄crank shaft曲柄轴[kræŋk]augular offset角度偏差velocity速度[vi‘lɔsiti]production tempo生产进度现状torque扭矩[tɔ:k]扭力ねじり力spline=the multiple keys花键[splain] [‘mʌltipl]スプラインquenching淬火焼き入れtempering回火焼き戻しannealing退火軟「やわ」らかくなる,焼きが戻るcarbonization碳化カーボニゼーションalloy合金アロイtungsten high speed steel钨高速工具钢高速度「そくど」鋼moly high speed steel钼高速工具钢[‘məuli]organic solvent有机溶剂[ɔ:‘ɡænik][’sɔlvənt]有機溶剤：ゆうきようざいbracket小磁导ブラケットliaison联络单volatile挥发性[‘vɔlətail]揮発：きはつresistance电阻ion离子titrator滴定仪[‘taitreitə]beacon警示灯[‘bi:kən]coolant冷却液[‘ku:lənt]冷却剤：れいきゃくcrusher破碎机[‘krʌʃə]クラッシャー模具工程类plain die简单模プライン・ダイ9pierce die冲孔模[piəs]ピアース・ダイforming die成型模フォーミング・ダイprogressive die连续模プログレッシブ・ダイgang dies复合模ギャング・ダイザshearing die剪边模シアリング・ダイriveting die铆合模リベッティング・ダイpierce冲孔ピアースforming成型(抽凸,冲凸) フォーミングdraw hole抽孔，拉空ドロー・ホールbending折弯ベンディング（・マシン）trim切边ツリムemboss凸点エンボスdome凸圆ドームsemi-shearing半剪セミ・シアリングstamp mark冲记号スタンプ・マークdeburr or coin压毛边[di‘bə:]deburr清理毛刺punch riveting冲压铆合パンチ・リベッティングside stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) スタンプ・レターshearing剪断シアリングtick-mark nearside正面压印正面チック・マークtick-mark farside反面压印冲压名称类extension dwg展开图エクステンションprocedure dwg工程图プロシージャーdie structure dwg模具结极图ダイ・ストラクチャーmaterial材质material thickness料片厚度シックネス（・ゲージ间隙规）factor系数ファクターupward向上アップワードdownward向下ダウンワードpress specification冲床规格プレス・スぺシフィケーションdie height range适用模高ダイ・ハイト・レンジdie height闭模高度ダイ・ハイトburr毛边バーgap间隙ギャップweight重量ウエイトtotal wt.总重量トータルpunch wt.上模重量パンチ五金零件类inner guiding post内导柱イナー・ガイディング・ポストinner hexagon screw内六角螺钉イナー・ヘキサゴン・スクリュー[‘heksəɡən]dowel pin固定销，连接销[‘dauəl]coil spring圆弹簧コイル・スプリングlifter pin顶料销リフター・ピンeq-height sleeves=spool等高套筒スリーブpin销ピンlifter guide pin浮升导料销リフター・ガイド・ピンguide pin导正销ガイド・ピンwire spring圆线弹簧ワイア/ワイヤ・スプリングouter guiding post外导柱アウター・ガイディング・ポストstop screw止付螺丝ストップ・スクリューlocated pin定位销outer bush外导套模板类top plate上托板（顶板）トップ・プレートtop block上垫脚トップ・ブロックpunch set上模座パンチ・セットpunch pad上垫板パンチ・パッドpunch holder上夹板パンチ・ホールダーstripper pad脱料背板ストリッパー・パッドup stripper上脱料板アップ・ストリッパーmale die公模(凸模) メール・ダイfeature die公母模フィーチャー・ダイfemale die母模(凹模) フィーメール・ダイ10upper plate上模板アッパー・プレートlower plate下模板ローワー・プレートdie pad下垫板ダイ・パッドdie holder下夹板ダイ・ホールダーdie set下模座ダイ・セットbottom block下垫脚ボタム/ボトム・ブロックbottom plate下托板(底板) ボタム/ボトム・プレートstripping plate内外打(脱料板) ストリッピング・プレートouter stripper外脱料板アウト・ストリッパーinner stripper内脱料板イナー・ストリッパーlower stripper下脱料板ローワー・ストリッパー零件类punch冲头パンとinsert入块(嵌入件) インサートdeburring punch压毛边冲子groove punch压线冲子グル―ブ・パンチstamped punch字模冲子スタンプ・パンチround punch圆冲子ラウンドパンチspecial shape punch异形冲子スペシャル・シェープ・パンチbending block折刀ベンディング・ブロックベンディング・マシン折弯机roller滚轴ローラーbaffle plate挡块バッフル・プレートlocated block定位块ブロックlocating ロケーティングsupporting block for location定位支承块サポーティング・ブロックair cushion plate气垫板エア・クッション・プレートair-cushion eject-rod气垫顶杆エア・クッションイジェクト・ロドtrimming punch切边冲子トリミング・パンチstiffening rib punch = stinger 加强筋冲子リブ・パンチstiffener 加强杆，加强板スチフナーribbon punch压筋冲子リボン・パンチreel-stretch punch卷圆压平冲子[stretʃ] リール・ストレッチ・パンチreel转轴リールguide plate定位板ガイド・プレートsliding block滑块スライディング・ブロックsliding dowel block滑块固定块[‘dauəl] スライディング・ブロックactive plate活动板アクチブ/アクティブlower sliding plate下滑块板ローワー・スライディング・プレートupper holder block上压块アッパー・ホールダー・ブロックupper mid plate上中间板アッパー・ミッド・プレートspring box弹簧箱スプリング・ボックスspring-box eject-rod弹簧箱顶杆スプリング・ボックスイジェクト・ロドspring-box eject-plate弹簧箱顶板スプリング・ボックスイジェクト・プレートbushing bolck衬套ブッシング・ブロックcover plate盖板カバー・プレートguide pad导料块ガイド・パッド塑件&模具相关英文compresion molding压缩成型コンプレッション・モールディングflash mold溢流式模具フラッシュ・モールドpositive mold挤压式模具ポジティブ・モールドsplit mold分割式模具スッポリッと・モールドcavity型控母模キャビティーcore模心公模コアtaper锥拔テーパーleather cloak仿皮革レザー・クロークshiver饰纹シバ破片、破片flow mark流痕フロー・マークwelding mark溶合痕ウエルジング/ウエルディング・マークpost screw insert螺纹套筒埋值ポスト・スクリ11ュー・インサートself tapping screw自攻螺丝セルフ・タッピング・スクシューstriper plate脱料板ストライプ・プレートpiston活塞ピストンcylinder汽缸套シリンダーchip细碎物チップhandle mold手持式模具ハンドル・モールド移转成型用模具encapsulation molding低压封装成型[in、kæpsju ‘leiʃən]エンキャップシュレーション・モールディング射出成型用模具two plate两枀式（模具）ツー・プレットwell type蓄料井ウエル・タイプinsulated runner绝缘浇道方式インシュレテッド・insulated cable绝缘电缆インシュレテッド・ケーブル・ランナーhot runner热浇道ハッと・ランナーrunner plat e浇道模块ランナー・プレットvalve gate阀门浇口バレブ・ゲットband heater环带状的电热器バンド・ヒーターspindle阀针スピンドルspear head刨尖头スピアヘッド先锋slag well冷料井スラグ・ウエルcold slag冷料渣コールド・スラグair vent排气道エア・ベンツh=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕ウエルディング・ラインeject pin顶出针イジェクト・ピンknock pin顶出销ノック・ピンreturn pin回位销反顶针リターン・ピンsleeve套筒スリーブstripper plate脱料板ストリッバー・プレットinsert core放置入子インサートinset 镶边インセットrunner stripper plate浇道脱料板ランナー・ストリッバー・プレットguide pin导销ガイド・ピンeject rod (bar)（成型机）顶业捧イジェクト・ロッド（バー）subzero深冷处理three plate三枀式模具スリー・プレットrunner system浇道系统ランナー・システムstress crack应力电裂ストレス・クラックstressストレス・レレーブドrelieved/stressrelief /Relief stress /Stress-relieving消除应力orientation定向オリェンテーション入学sprue gate射料浇口，直浇口スプレー・ゲ―トsprue主流道スプレーnozzle射嘴ノズルsprue lock pin料头钩销(拉料杆) スプレー・ロック・ピンside gate侧浇口サイド・ゲートedge gate侧缘浇口エッジ・ゲートtab gate搭接浇口タブ・ゲートfilm gate薄膜浇口フィルム・ゲートflash gate闸门浇口フラッシュ・ゲートslit gate缝隙浇口スリット・ゲートfan gate扇形浇口ファン・ゲートdish gate因盘形浇口ディッシュ・ゲートH=F=1/2t~1/5tT=2.5~3.5mmdiaphragm [‘daiəfræm]gate隔膜浇口ダイヤフラム・ゲートring gate环形浇口リング・ゲートsubmarine gate潜入式浇口サブマリン・ゲートtunnel gate隧道式浇口トンネル・ゲートpin gate针点浇口ピン・ゲートΦ0.8~1.0mmRunner less无浇道ランナー・レス(sprue less)无射料管方式スプレー・レス12long nozzle延长喷嘴方式ロング・ノズルsprue浇口;溶渣[spru:] スプルー品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员プロセスOQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查Article物品FAA first article assurance 首件硭认TVR tool verification report 模具硭认报告3B 3B 模具正式投产前硭认[、verifi‘keiʃən] CP capability index 能力指数[、keipə‘biləti] CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查audit [‘ɔ:dit]QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 枀严重的MAJ Major 主要的MIN Minor 轻微的AOQ A verage Output Quality 平均出厂品质AOQL A verage Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR A verary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点13QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-CompaqS-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求14L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 枀严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养A TIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 硭认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MA T'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumerelectronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital V edio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID Manufacturing15CAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结极MCA Micro Channel Architecture 微通道结极EISA Extended Industry Standard Architecture 扩充的工业标准结极SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法16。
机械类常用英语：组装、冲压、喷漆
Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein |刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称ad mini stration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑。
非常实用的汽车零部件行业英语词汇
制程不良
163 poor staking
铆合不良
164 position
职务
165 power button
电源按键
166 power wire
电源线
167 prepare for, make preparations for 准备
168 president
董事长
169 pressure plate=plate pinch
71 excesssive gap
间隙过大
72 exposed metal/bare metal
金属裸露
73 factory director
厂长
74 failure, trouble
故障
75 fasten
锁紧(螺丝)
76 feature change
特性变更
77 feeder
送料机
78 feeding is not in place
生产
No.
1.组装、冲压、喷漆、生产线词汇
176 projects
企划
177 proposal improvement
提案改善
178 PRS Pairs
双(对)
179 punch press, dieing out press 冲床
180 punching machine 181 qualified-products,/up-to-
缩水
207 shut die
架模
208 shut height of a die
架模高度
209 sliding rack
210
slipped screwhead/shippery screw thread
组装、冲压、喷漆等英文专业词汇
組裝、衝壓、噴漆等專業詞匯Assembly line組裝線Layout布置圖Conveyer流水線物料板Rivet table拉釘機Rivet gun拉釘槍Screw driver起子Electric screw driver電動起子Pneumatic screw driver氣動起子worktable 工作桌OOBA開箱檢查fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine熱熔機repair修理operator作業員QC品管supervisor 課長ME制造工程師MT製造生技cosmetic inspect外觀檢查inner parts inspect內部檢查thumb screw大頭螺絲lbs.inch鎊、英寸EMI gasket導電條front plate前板rear plate后板chassis |'∫æsi|基座bezel panel面板power button電源按鍵reset button重置鍵Hi-pot test of SPS高源高壓測試Voltage switch of SPS電源電壓接柆鍵sheet metal parts 沖件plastic parts塑膠件SOP製造作業程序material check list物料檢查表work cell工作間trolley台車carton紙箱sub-line支線left fork叉車personnel resource department 人力資源部production department生產部門planning department企劃部QC Section品管科stamping factory沖壓廠painting factory烤漆廠molding factory成型廠common equipment常用設備uncoiler and straightener整平機punching machine 沖床robot機械手hydraulic machine油壓機lathe車床|刨床 planer |'pleinmiller銑床grinder磨床driller鉆床linear cutting線切割electrical sparkle電火花welder電焊機staker=reviting machine鉚合機position職務president董事長general manager總經理special assistant manager特助factory director廠長department director部長deputy manager |'depjuti| =vice manager副理section supervisor課長deputy section supervisor =vice section superisor副課長group leader/supervisor組長line supervisor線長assistant manager助理to move, to carry, to handle搬運be put in storage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺final inspection終檢to connect material接料to reverse material 翻料wet station沾濕台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|報廢scrape ..v.刮;削deficient purchase來料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' n|氧化 ksi'deiscratch刮傷dents壓痕defective upsiding down抽芽不良defective to staking鉚合不良mp|鑲塊 embeded lump|in'bed| |l feeding is not in place送料不到位stamping-missing漏沖production capacity生產力education and training教育與訓練proposal improvement提案改善spare parts=buffer備件forklift叉車trailer=long vehicle拖板車compound die合模die locker鎖模器pressure plate=plate pinch壓板bolt螺栓name of a department部門名稱administration/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzle蜂鳴器defective product label不良標簽identifying sheet list標示單screwdriver holder起子插座pedal踩踏板stopper阻擋器flow board流水板hydraulic handjack油壓板車forklift叉車pallet棧板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger無名指little finger小指band-aid創可貼iudustrial alcohol工業酒精alcohol container沾濕台head of screwdriver起子頭sweeper掃把mop拖把vaccum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain鏈條jack升降機production line流水線chain鏈條槽magnetizer加磁器lamp holder燈架to mop the floor拖地to clean the floor掃地to clean a table擦桌子air pipe 氣管packaging tool打包機packaging打包missing part漏件wrong part錯件excessive defects過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外觀不良slipped screwhead/slippery screw head螺絲滑頭slipped screwhead/shippery screw thread滑手speckle斑點mildewed=moldy=mouldy發霉rust生銹deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excesssive gap間隙過大grease/oil stains油污inclusion雜質painting peel off臟污shrinking/shrinkage縮水mixed color雜色scratch劃傷poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬polishing/surface processing表面處理exposed metal/bare metal金屬裸露lack of painting烤漆不到位safety安全quality品質delivery deadline交貨期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企劃QC品管die worker模工production, to produce生產equipment設備to start a press開機stop/switch off a press關機classification整理regulation整頓cleanness清掃conservation清潔culture教養qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste廢料board看板feeder送料機sliding rack滑料架defective product box不良品箱die change 換模to fix a die裝模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket膠筐isolating plate baffle plate; barricade隔板carton box紙箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料transportation運輸(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料變更feature change 特性變更evaluation評估prepare for, make preparations for 準備parameters參數rotating speed, revolution轉速manufacture management製造管理abnormal handling異常處理production unit生產單位lots of production生產批量steel plate鋼板roll material捲料manufacture procedure制程operation procedure作業流程to revise, modify修訂to switch over to, switch---to throw--over switching over切換engineering, project difficulty工程瓶頸stage die工程模automation自動化to stake, staking, reviting鉚合add lubricating oil加潤滑油shut die架模shut height of a die架模高度analog-mode device類模器die lifter舉模器argon welding氬焊vocabulary for stamping衝壓常詞匯stamping, press沖壓punch press, dieing out press沖床uncoiler & strainghtener整平機feeder送料機rack, shelf, stack料架cylinder油缸robot機械手taker取料機conveyer belt輸送帶transmission rack輸送架top stop上死點bottom stop下死點one stroke一行程inch寸動to continue, cont.連動to grip(material)吸料location lump, locating piece, block stop 定位塊reset復位smoothly順利dent壓痕scratch刮傷deformation變形filings鐵削to draw holes抽孔inquiry, search for查尋to stock, storage, in stock庫存receive領取approval examine and verify審核processing, to process加工delivery, to deliver 交貨to return delivenry to. to send delinery back to retrn of goods退貨registration登記registration card登記卡to control管制to put forward and hand in提報safe stock安全庫存acceptance = receive驗收to notice通知application form for purchase請購單consume, consumption消耗to fill in填寫abrasion磨損reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics統計demand and supply需求career card履歷卡to take apart a die卸下模具to load a die裝上模具to tight a bolt擰緊螺栓to looser a bolt擰鬆螺栓to move away a die plate移走模板easily damaged parts易損件standard parts標準件breaking.(be)broken,(be)cracked 斷裂to lubricate潤滑common vocabulary for die engineering模具工程常用詞匯die 模具figure file, chart file圖檔cutting die, blanking die沖裁模progressive die, follow (-on)die連續模compound die復合模punched hole沖孔panel board鑲塊to cutedges=side cut=side scrap切邊to bending折彎to pull, to stretch拉伸Line streching, line pulling線拉伸engraving, to engrave刻印upsiding down edges翻邊to stake鉚合designing, to design設計design modification設計變化die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上墊板spare dies模具備品spring 彈簧bolt螺栓document folder文件夾file folder資料夾to put file in order整理資料spare tools location手工備品倉first count初盤人first check初盤復櫂人second count 復盤人second check復盤復核人equipment設備waste materials廢料work in progress product在制品casing = containerazation裝箱quantity of physical invetory second count 復盤點數量quantity of customs count會計師盤,點數量the first page第一聯filed by accounting department for reference會計部存查end-user/using unit(department)使用單位summary of year-end physical inventory bills年終盤點截止單據匯總表bill name單據名稱This sheet and physical inventory list will be sent to accounting department together (Thoseof NHK will be sent to financial department)本表請與盤點清冊一起送會計部－(NHK廠區送財會部)Application status records of year-end physical inventory List and physical inventory card年終盤點卡與清冊使用－狀況明細表blank and waste sheet NO.空白與作廢單號plate電鍍mold成型material for engineering mold testing工程試模材料not included in physical inventory不列入盤點sample樣品incoming material to be inspected進貨待驗description品名steel/rolled steel鋼材material statistics sheet物料統計明細表meeting minutes會議記錄meeting type 會別distribution department分發單位location地點chairman主席present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位pre-fixed finishing date預定完成日approved by / checked by / prepared by核準/審核/承辦PCE assembly production schedule sheetPCE組裝廠生產排配表model機鍾work order工令revision版次remark備注production control confirmation生產確認checked by初審approved by核準department部門stock age analysis sheet庫存貨齡分析表on-hand inventory現有庫存available material良品可使用obsolete material良品已呆滯to be inspected or reworked待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by制表notes說明year-end physical inventory difference analysis sheet年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head挂鉤槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch=die button圓沖子shape punch=die insert異形子stock locater block定位塊under cut=scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬desmut剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished products成品disposed products處理品barcode條碼flow chart流程表單assembly組裝stamping沖壓molding成型spare parts=buffer備品coordinate座標dismantle the die折模auxiliary fuction輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫derusting machine除銹機degate打澆口dryer烘干機induction感應induction light感應光response=reaction=interaction感應ram連杆edge finder巡邊器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delamination起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule=peuet=grain細粒grit maker抽粒機cushion緩沖magnalium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane鉋grind磨drill鋁boring鏜blinster氣泡fillet鑲;嵌邊through-hole form通孔形式voller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸augular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline=the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模gang dies複合模shearing die剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸) draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號) shearing剪斷tick-mark nearside正面壓印tick-mark farside反面壓印沖壓名稱類extension dwg展開圖procedure dwg工程圖die structure dwg模具結構圖material材質material thickness料片厚度factor系數upward向上downward向下press specification沖床規格die height range適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves=spool等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套模板類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板) stripping plate內外打(脫料板) outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板零件類punch沖頭insert入塊(嵌入件) deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖子guide plate定位板sliding block滑塊sliding dowel block滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing bolck襯套cover plate蓋板guide pad導料塊塑件&模具相關英文compre sion molding壓縮成型flash mold溢流式模具plsitive mold擠壓式模具split mold分割式模具cavity型控母模core模心公模taper錐拔leather cloak倣皮革shiver飾紋flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋值self tapping screw自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulation molding低壓封裝成型射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleave套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆) slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜澆口ring gate環形澆口subarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口Φ0.8~1.0mmRunner less無澆道(sprue less)無射料管方式long nozzle延長噴嘴方式sprue澆口;溶渣品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認TVR tool verification report 模具確認報告3B 3B 模具正式投產前確認CP capability index 能力指數CPK capability index of process 模具製程能力參數SSQA standardized supplier quality 合格供應商品質評估OOBA out of box audit 開箱檢查QFD quality function deployment 品質機能展開FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8項回復內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的AOQ Average Output Quality 平均出廠品質AOQL Average Output Quality Level 平均出廠品質Q/R/S Quality/Reliability/Service 品質/可靠度服務MIL-STD Military-Standard 軍用標準S I-S IV Special I-Special IV 特殊抽樣水準等級P/N Part Number 料號L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑FREQ Frequency 頻率N Number 樣品數其它品質術語類QCC Quality Control Circle 品質圈QIT Quality Improvement Team 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQL Limiting Quality Level 最低品質水準RMA Return Material Audit 退料認可QAN Quality Amelionrate Notice 品質改善活動ADM Absolute Dimension Measuremat 全尺寸測量QT Quality Target 品質目標7QCTools 7 Quality Controll Tools 品管七大手法通用之件類ECN Engineering Change Notes工程變更通知(供應商) ECO Engineering Change Order 工程改動要求(客戶) PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類QC Quality System 品質系統ES Engineering Standarization 工程標準CGOO China General PCE龍華廠文件H Huston (美國)休斯敦C Compaq (美國)康伯公司C China 中國大陸A Assembly 組裝(廠)S Stamping 沖壓(廠)P Painting 烤漆(廠)I Intel 英特爾公司T TAIWAN 臺灣IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq產品在龍華衝壓廠製造作業規範CQCA Q-Quality A-Assembly Compaq產品在龍華組裝廠品管作業規範CQCP P-Painting Compaq產品在龍華烤漆廠品管作業規範部類PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產計劃控制MC Material Control 物料控制ME Manafacture Engineering 製造工程部PE Project Engineering 產品工程部A/C Accountant Dept 會計部P/A Personal & Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Labratry 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Asssembly 組裝(廠)S Stamping 沖壓(廠)生產類PCS Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號其它OEM Original Equipment Manufacture 原設備製造PCE Personal Computer Enclosure 個人電腦外設PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器SECC SECC` 電解片SGCC SGCC 熱浸鍍鋅材料NHK North of Hongkong 中國大陸PRC People's Republic of China 中國大陸U.S.A the United States of America美國A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量VS 以及REV Revision 版本JIT Just In Time 零庫存I/O Input/Output 輸入/輸出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許ESD Electry-static Discharge 靜電排放5S 希臘語整理,整頓,清掃,清潔,教養ATIN Attention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只讀光碟FDD Floppy Disk Drive 軟碟機HDD Hard Disk Drive 碟碟機REF Reference 僅供參考CONN Connector 連接器CAV Cavity 模穴CAD Computer Aid Design 計算機輔助設計ASS'Y Assembly 裝配,組裝MAT'S Material 材料IC Integrated Circuit 集成電路T/P True Position 真位度TYP Type 類型WDR Weekly Delivery Requitement 周出貨需求C?T Cycle Time 制程周期L/T Lead Time 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer,Commumcation,Consumer electronic's 消費性電子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證DQA Desigh Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Rejeet Rate 批退率BS Brain storming 腦力激蕩EMI Electronic Magnetion Inspect 高磁測試FMI Frequency Modulatim Inspect 高頻測試B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先進的基本輸入/輸出系統CMOS Complemeruary Metoll Oxide Semiconductor 互補金屬氧化物半導體PDA Personal Digital Assistant 個人數字助理IC Integrated Circuit 集成電路ISA Industry Standard Architecture 工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LED Light-Emitting Diode 發光二級管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金屬線緒束集組件F/C Flat Calle 排線PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WPR Weekly Delivery Requirement 周出貨要求PPM Parts Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requiremcnt Planning 物料需計劃OC Operation System 作業系統TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Sizeugboss发帖: 60积分: 1于2003-02-18 08:58 [信息] [悄悄话] [Email] [引用] [搜索] [复制] [收藏] ________________________________________模具技術用語各種模具常用成形方式accurate die casting 精密壓鑄powder forming 粉末成形calendaring molding 壓延成形powder metal forging 粉末鍛造cold chamber die casting 冷式壓鑄precision forging 精密鍛造cold forging 冷鍛press forging 沖鍛compacting molding 粉末壓出成形rocking die forging 搖動鍛造compound molding 複合成形rotary forging 迴轉鍛造compression molding 壓縮成形rotational molding 離心成形dip mold 浸漬成形rubber molding 橡膠成形encapsulation molding 注入成形sand mold casting 砂模鑄造extrusion molding 擠出成形shell casting 殼模鑄造foam forming 发泡成形sinter forging 燒結鍛造forging roll 軋鍛six sides forging 六面鍛造gravity casting 重力鑄造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高壓鑄造hot chamber die casting 熱室壓鑄swaging 擠鍛hot forging 熱鍛transfer molding 轉送成形injection molding 射出成形warm forging 溫鍛investment casting 精密鑄造matched die method 對模成形法laminating method 被覆淋膜成形low pressure casting 低壓鑄造lost wax casting 脫蠟鑄造matched mould thermal forming 對模熱成形模各式模具分類用語bismuth mold 鉍鑄模landed plunger mold 有肩柱塞式模具burnishing die 擠光模landed positive mold 有肩全壓式模具button die 鑲入式圓形凹模loading shoe mold 料套式模具center-gated mold 中心澆口式模具loose detail mold 活零件模具chill mold 冷硬用鑄模loose mold 活動式模具clod hobbing 冷擠壓製模louvering die 百葉窗沖切模composite dies 複合模具manifold die 分歧管模具counter punch 反凸模modular mold 組合式模具double stack mold 雙層模具multi-cavity mold 多模穴模具electroformed mold 電鑄成形模multi-gate mold 複式澆口模具expander die 擴徑模offswt bending die 雙折冷彎模具extrusion die 擠出模palletizing die 疊層模family mold 反套製品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通氣性模具duplicated cavity plate 複板模positive mold 全壓式模具fantail die 扇尾形模具pressure die 壓緊模fishtail die 魚尾形模具profile die 輪廓模flash mold 溢料式模具progressive die 順序模gypsum mold 石膏鑄模protable mold 手提式模具hot-runner mold 熱流道模具prototype mold 雛形試驗模具ingot mold 鋼錠模punching die 落料模lancing die 切口模raising(embossing) 壓花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 無流道冷料模具sectional die 對合模具segment mold 組合模semi-positive mold 半全壓式模具shaper 定型模套single cavity mold 單腔模具solid forging die 整體鍛模split forging die 拼合鍛模split mold 雙併式模具sprueless mold 無注道殘料模具squeezing die 擠壓模stretch form die 拉伸成形模sweeping mold 平刮鑄模swing die 振動模具three plates mold 三片式模具trimming die 切邊模unit mold 單元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 軛型模模具廠常用之標準零配件air vent vale 通氣閥anchor pin 錨梢angular pin 角梢baffle 調節阻板angular pin 傾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑塊binder plate 壓板blank holder 防皺壓板blanking die 落料沖頭bolster 上下模板bottom board 澆注底板bolster 墊板bottom plate 下固定板bracket 扥架bumper block 緩衝塊buster 堵口casting ladle 澆注包casting lug 鑄耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 鎖定塊coil spring 螺旋彈簧cold punched nut 冷沖螺母cooling spiral 螺旋冷卻栓core 心型core pin 心型梢cotter 開口梢cross 十字接頭cushion pin 緩衝梢diaphragm gate 盤形澆口die approach 模頭料道die bed 型底die block 塊形模體die body 鑄模座die bush 合模襯套die button 沖模母模die clamper 夾模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 沖模板die set 沖壓模座direct gate 直接澆口dog chuck 爪牙夾頭dowel 定位梢dowel hole 導套孔dowel pin 合模梢dozzle 輔助澆口dowel pin 定位梢draft 拔模錐度draw bead 張力調整桿drive bearing 傳動軸承ejection pad 頂出襯墊ejector 脫模器ejector guide pin 頂出導梢ejector leader busher 頂出導梢襯套ejector pad 頂出墊ejector pin 頂出梢ejector plate 頂出板ejector rod 頂出桿ejector sleeve 頂出襯套ejector valve 頂出閥eye bolt 環首螺栓filling core 椿入蕊film gate 薄膜形澆口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圓形模板fixed bolster plate 固定側模板flanged pin 帶凸緣销flash gate 毛邊形澆口flask 上箱floating punch 浮動沖頭gate 澆口gate land 澆口面gib 凹形拉緊销goose neck 鵝頸管guide bushing 引導襯套guide pin 導梢guide post 引導柱guide plate 導板guide rail 導軌head punch 頂镦沖頭headless punch 直柄沖頭heavily tapered solid 整體模蕊盒hose nippler 管接頭impact damper 緩衝器injection ram 壓射柱塞inlay busher 嵌入襯套inner plunger 內柱塞inner punch 內沖頭insert 嵌件insert pin 嵌件梢king pin 轉向梢king pin bush 主梢襯套knockout bar 脫模杵land 合模平坦面land area 合模面leader busher 導梢襯套lifting pin 起模頂销lining 內襯locating center punch 定位中心沖頭locating pilot pin 定位導梢locating ring 定位環lock block 壓塊locking block 定位塊locking plate 定位板loose bush 活動襯套making die 打印沖子manifold block 歧管檔塊master plate 靠模樣板match plate 分型板mold base 塑膠模座mold clamp 鑄模緊固夾mold platen 模用板moving bolster 換模保持裝置moving bolster plate 可動側模板one piece casting 整體鑄件parallel block 平行墊塊paring line 分模線parting lock set 合模定位器pass guide 穴型導板peened head punch 鑲入式沖頭pilot pin 導销pin gate 針尖澆口plate 襯板pre extrusion punch 頂擠沖頭punch 沖頭puncher 推桿pusher pin 襯套梢rack 機架rapping rod 起模桿re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮動脫模器ring gate 環型澆口roller 滾筒runner 流道runner ejector set 流道頂出器runner lock pin 流道拉梢screw plug 頭塞set screw 固定螺絲shedder 脫模裝置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺絲skeleton 骨架slag riser 冒渣口slide(slide core) 滑塊slip joint 滑配接頭spacer block 間隔塊spacer ring 間隔環spider 模蕊支架spindle 主軸sprue 注道sprue bushing 注道襯套sprue bushing guide 注道導套sprue lock bushing 注道定位襯套sprue puller 注道拉料销spue line 合模線square key 方鍵。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
組裝、衝壓、噴漆等專業詞匯Assembly line 組裝線 Layout 布置圖Conveyer 流水線物料板 Rivet table 拉釘機 Rivet gun 拉釘槍 Screw driver 起子Electric screw driver 電動起子 Pn e u m a t i c s c r e w d r i v e r 氣 worktable 工作桌 OOBA 開箱檢查 fit together 組裝在一起 fasten 鎖緊(螺絲) fixture 夾具(治具) pallet 棧板 barcode 條碼barcode scanner 條碼掃描器 fuse together 熔合 fuse machine 熱熔機 repair 修理 operator 作業員 QC品管 supervisor 課長 ME 制造工程師 MT製造生技 cosmetic inspect 外觀檢查 inner parts inspect 內部檢查 thumb screw 大頭螺絲 Lbs. inch 鎊、英寸 EMI gasket 導電條 front plate 前板 rear plate 后板chassis |'∫æsi| 基座 bezel panel 面板 power button 電源按鍵 reset button 重置鍵Hi-pot test of SPS 高源高壓測試V oltage switch of SPS電源電壓接柆鍵 sheet metal parts 沖件 plastic parts 塑膠件 SOP 製造作業程序material check list 物料檢查表 work cell 工作間 trolley 台車 carton 紙箱 sub-line 支線 left fork 叉車Personnel resource department 人力資源部production department 生產部門 planning department 企劃部 QC Section 品管科 stamping factory 沖壓廠 painting factory 烤漆廠 molding factory 成型廠 common equipment 常用設備 uncoiler and straightener 整平機 punching machine 沖床 robot 機械手hydraulic machine 油壓機 lathe 車床 planer |'plein |刨床miller 銑床 grinder 磨床 driller 鉆床 linear cutting 線切割 electrical sparkle 電火花 welder 電焊機staker = riveting machine 鉚合機 position 職務 president 董事長 general manager 總經理 special assistant manager 特助 factory director 廠長department director 部長 deputy manager |'depjuti| =vice manager 副理 section supervisor 課長 deputy section supervisor =vice section supervisor 副課長 group leader/supervisor 組長 line supervisor 線長 assistant manager 助理 to move, to carry, to handle 搬運 be put in storage 入庫 pack packing 包裝 to apply oil 擦油 to 銼毛刺 final inspection 終檢 to connect material 接料 to reverse material 翻料 wet station 沾濕台 Tiana 天那水 cleaning cloth 抹布 to load material 上料 to unload material 卸料 to return material/stock to 退料 scraped |'skr æpid|報廢 scrape ..v.刮;削deficient purchase 來料不良 manufacture procedure 制程deficient manufacturing procedure制程不良 oxidation |' ksi'dei n|氧化scratch 刮傷 dents 壓痕defective upsiding down 抽芽不良defective to staking 鉚合不良 embedded lump |in'bed| |l mp|鑲塊feeding is not in place 送料不到位stamping-missing 漏沖 production capacity 生產力education and training 教育與訓練proposal improvement 提案改善 spare parts =buffer 備件 forklift 叉車trailer =long vehicle 拖板車 compound die 合模 die locker 鎖模器pressure plate =plate pinch 壓板 bolt 螺栓name of a department 部門名稱 administration/general affairs dept 總務部automatic screwdriver 電動啟子 thickness gauge 厚薄規 gauge(or jig)治具 power wire 電源線 buzzer 蜂鳴器defective product label 不良標簽 identifying sheet list 標示單 screwdriver holder 起子插座 pedal 踩踏板 stopper 阻擋器 flow board 流水板hydraulic hand jack 油壓板車 forklift 叉車 pallet 棧板 glove(s)手套gl o v e (s ) w thumb 大拇指 forefinger 食指 mid finger 中指 ring finger 無名指 little finger 小指 Band-Aid 創可貼Industrial alcohol 工業酒精 alcohol container 沾濕台 head of screwdriver 起子頭 sweeper 掃把 mop 拖把vacuum cleaner 吸塵器 rag 抹布garbage container 灰箕 garbage can 垃圾箱 garbage bag 垃圾袋 chain 鏈條 jack 升降機production line 流水線 chain 鏈條槽 magnetizer 加磁器 lamp holder 燈架 to mop the floor 拖地 to clean the floor 掃地 to clean a table 擦桌子 air pipe 氣管 packaging tool 打包機 packaging 打包 missing part 漏件 wrong part 錯件excessive defects 過多的缺陷 critical defect 極嚴重缺陷 major defect 主要缺陷 minor defect 次要缺陷 not up to standard 不合規格 dimension/size is a little bigger 尺寸偏大(小)cosmetic defect 外觀不良 slipped screw head/slippery screw head 螺絲滑頭 slipped screw head/slippery screw thread 滑手 speckle 斑點mildewed =moldy = mouldy 發霉 rust 生銹 deformation 變形 burr(金屬)flash(塑件)毛邊 poor staking 鉚合不良excessive gap 間隙過大 grease/oil stains 油污 inclusion 雜質 painting peel off 臟污 shrinking/shrinkage 縮水 mixed color 雜色 scratch 劃傷poor processing 制程不良 poor incoming part 事件不良 fold of packaging belt 打包帶折皺 painting make-up 補漆 discoloration 羿色 water spots 水漬po l i s h i n g /s u r f a c e p r o c e s s i exposed metal/bare metal 金屬裸露 lack of painting 烤漆不到位 safety 安全 quality 品質delivery deadline 交貨期 cost 成本 engineering 工程 die repair 模修enterprise plan = enterprise expansion projects 企劃 QC品管 die worker 模工production, to produce 生產 equipment 設備 to start a press 開機 stop/switch off a press 關機 classification 整理 regulation 整頓 cleanness 清掃 conservation 清潔 culture 教養qualified products, up-to-grade products 良品 defective products, not up-to-grade products 不良品waste廢料board看板feeder送料機sliding rack滑料架defective product box不良品箱die change 換模to fix a die裝模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket膠筐isolating plate baffle plate; barricade隔板carton box紙箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料transportation運輸(be)qualified, up to grade合格not up to grade, not qualified不合格material change, stock change材料變更feature change 特性變更evaluation評估prepare for, make preparations for 準備parameters參數rotating speed, revolution轉速manufacture management製造管理abnormal handling異常處理production unit生產單位lots of production生產批量steel plate鋼板roll material捲料manufacture procedure制程operation procedure作業流程to revise, modify修訂to switch over to, switch---tothrow--over switching over切換engineering, project difficulty工程瓶頸stage die工程模automation自動化to stake, staking, riveting鉚合add lubricating oil加潤滑油shut die架模shut height of a die架模高度analog-mode device類模器die lifter舉模器argon welding氬焊Vocabulary for stamping衝壓常詞匯stamping, press沖壓punch press, dicing out press沖床uncoiler & strainghtener整平機feeder送料機rack, shelf, stack料架cylinder油缸robot機械手taker取料機conveyer belt輸送帶transmission rack輸送架top stop上死點bottom stop下死點one stroke一行程inch寸動to continue, cont.連動to grip(material)吸料location lump, locating piece,block stop 定位塊reset復位smoothly順利dent壓痕scratch刮傷deformation變形filings鐵削to draw holes抽孔inquiry, search for查尋to stock, storage, in stock庫存receive領取approval examine and verify審核processing, to process加工delivery, to deliver 交貨to return delivery to. to senddeliverybacktoreturnogregistration登記registration card登記卡to control管制to put forward and hand in提報safe stock安全庫存acceptance = receive驗收to notice通知applicationformforconsume, consumption消耗to fill in填寫abrasion磨損reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics統計demand and supply需求career card履歷卡to take apart a die卸下模具to load a die裝上模具to tight a bolt擰緊螺栓to looser a bolt擰鬆螺栓to move away a die plate移走模板easily damaged parts易損件standard parts標準件Breaking. (be)broken,(be)cracked斷裂to lubricate潤滑common vocabulary for die engineering模具工程常用詞匯die 模具figure file, chart file圖檔cutting die, blanking die沖裁模Progressive die, follow (-on) die 連續模compound die復合模punched hole沖孔panel board鑲塊to cut edge =side cut =side scrap切邊to bending折彎to pull, to stretch拉伸Line stretching, line pulling線拉伸engraving, to engrave刻印upside down edges翻邊to stake鉚合designing, to design設計design modification設計變化die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上墊板spare dies模具備品spring 彈簧bolt螺栓document folder文件夾資料夾to put order整理資料spare tools location手工備品倉first count初盤人first check初盤復櫂人second count 復盤人second check復盤復核人equipment設備waste materials廢料work in progress product在制品casing = containerization裝箱quantity of physical inventorysecond count 復盤點數量Quantity of customs counts會計師盤,點數量the first page第一聯filed by accounting departmentfor reference會計部存查end-user/using unit(department)使用單位Summary of year-end physicalinventory bills年終盤點截止單據匯總表bill name單據名稱This sheet and physicalinventory list will be sent toaccounting department together(Those of NHK will be sent tofinancial department)本表請與盤點清冊一起送會計部－(NHK廠區送財會部)Application status records ofyear-end physical inventory Listand physical inventory card年終盤點卡與清冊使用－狀況明細表Blank and waste sheet NO.空白與作廢單號plate電鍍mold成型material for engineering moldtesting工程試模材料not included in physicalinventory不列入盤點sample樣品incoming material to beinspected進貨待驗description品名steel/rolled steel鋼材Material statistics sheet物料統計明細表meeting minutes會議記錄meeting type 會別distribution department分發單位location地點chairman主席present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位pre-fixed finishing date預定完成日approved by / checked by /prepared by核準/審核/承辦PCE assembly productionschedule sheetPCE組裝廠生產排配表model機鍾work order工令revision版次remark備注production control confirmation生產確認checked by初審approved by核準department部門Stock age analysis sheet庫存貨齡分析表on-hand inventory現有庫存available material良品可使用obsolete material良品已呆滯To be inspected or reworked待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by制表notes說明Year-end physical inventory difference analysis sheet年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score =groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head挂鉤槽slug hole廢料孔feature die公母模expansion DWG展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch =die button圓沖子shape punch =die insert異形子stock located block定位塊under cut =scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬despot剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished products成品disposed products處理品barcode條碼flow chart流程表單assembly組裝stamping沖壓molding成型spare parts =buffer備品coordinate座標dismantle the die折模auxiliary function輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫derusting machine除銹機degate打澆口dryer烘干機induction感應induction light感應光response =reaction =interaction 感應ram連杆edge finder巡邊器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delaminating起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule =pellet =grain細粒grit maker抽粒機cushion緩沖magnesium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane鉋grind磨drill鋁boring鏜blister氣泡fillet鑲;嵌邊through-hole form通孔形式roller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸angular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline =the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模gang dies複合模shearing die剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸)draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號)shearing剪斷tick-mark nearside正面壓印tick-mark farside反面壓印沖壓名稱類extension DWG展開圖procedure DWG工程圖die structure DWG模具結構圖material材質material thickness料片厚度factor系數upward向上downward向下press specification沖床規格die height range適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves =spool等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套模板類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板) stripping plate內外打(脫料板) outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板零件類punch沖頭insert入塊(嵌入件) deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖子guide plate定位板sliding block滑塊sliding dowel block滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing block襯套cover plate蓋板guide pad導料塊塑件&模具相關英文compression molding壓縮成型flash mold溢流式模具positive mold擠壓式模具split mold分割式模具cavity型控母模core模心公模taper錐拔leather cloak倣皮革shiver飾紋flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋值self tapping screw自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulationmolding低壓封射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleeve套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆)--slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜澆口ring gate環形澆口submarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口Φ0.8~1.0mmRunner less無澆道(sprue less)無射料管方式long nozzle延長噴嘴方式spur澆口;溶stamping tool shop Istamping tool shop IIPCE mould shop Engineer standard Document centerSystem －Assembly molding painting assemuy通用類cosmetic inspection standard 外觀檢驗規範computer case 電腦外殼(組件) personal computer enclosure 電腦機箱產品Hood 上蓋spsbase pan 基座FDD bezel 面板riser card 擴充本flat cable 排線sheet material 板村Rou material 卷材mother material to sub－material feeding(喂料)→straightening (整平) rectifying (導正)→longitudinal cutting (縱剪) →separating (分離) →taking(取料)shop－traceller 天本TOP driver cage 上磁架bottom driver cage 干磁架I/O bracket 後窗resin film 樹脂膜impurity 雜質grease 油脂ventilation 通風peripheral equipment’s connector 外圍(輔助)設備連接器safe guard net 護軍welding sparkles 焊接火花stratification logistics 辦後勤學oreenization Color management 顏色管理Visual management 目視管理hydraulic APCopper au 銅錐slide caliper 游標卡尺Angle compasses 角度規external diameter (內)外徑Micrometer 螺旋測微器 feeler gauge 原薄規Screw meter 東規(螺旋量規) Torque meter 扭力計Pushing－pulling force meter 推拉計Combination jig 組合治具Single jig 單個治具flow card 流程卡Arrow labels 箭頭標簽 rust－proof 防透油Lubricant 潤滑油Horizontal coordinate 橫座標Vertical coordinate 縱座標daily report sheet 目報表Topcovar 上(頂)蓋 server 伺服器Inspection defect :Mismatch 銷件deformation 變形Nyt 生銹peel 脫漆Shrink scratch 刮份Contamination 臟污screwbioken 刮痕Dent 凹痕water spots 水漬Gap 間隙label errorMissing label 漏貼 rejection criteria 拒收標准Suspater品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認TVR tool verification report 模具確認報告3B 3B 模具正式投產前確認CP capability index 能力指數CPK capability index of process 模具製程能力參數SSQA standardized supplier quality 合格供應商品質評估OOBA out of box audit 開箱檢查QFD quality function deployment 品質機能展開FMEA failure model effectiveness analysis 失效模式分析8D 8 disciplines 8項回復內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的AOQ Average Output Quality 平均出廠品質AOQL Average Output Quality Level 平均出廠品質Q/R/S Quality/Reliability/Service 品質/可靠度服務MIL-STD Military-Standard 軍用標準S I-S IV Special I-Special IV 特殊抽樣水準等級P/N Part Number 料號L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproductivity & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑FREQ Frequency 頻率N Number 樣品數其它品質術語類QCC Quality Control Circle 品質圈QIT Quality Improvement Team 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQL Limiting Quality Level 最低品質水準RMA Return Material Audit 退料認可QAN Quality Ameliorate Notice 品質改善活動ADM Absolute Dimension Measurement 全尺寸測量QT Quality Target 品質目標7QCTools 7 Quality Control Tools 品管七大手法通用之件類ECN Engineering Change Notes 工程變更通知(供應商)ECO Engineering Change Order 工程改動要求(客戶)PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類QC Quality System 品質系統ES Engineering Standardization 工程標準CGOO China General PCE龍華廠文件H Houston (美國)休斯敦C Compaq (美國)康伯公司C China 中國大陸A Assembly 組裝(廠)S Stamping 沖壓(廠)P Painting 烤漆(廠)I Intel 英特爾公司T TAIWAN 臺灣IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格CMCS C-China M-Manufacture C-Compaq S-Stamping C ompaq產品在龍華衝壓廠製造作業規範CQCA Q-Quality A-Assembly Compaq產品在龍華組裝廠品管作業規範CQCP P-Painting Compaq產品在龍華烤漆廠品管作業規範部類PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產計劃控制MC Material Control 物料控制ME Manufacture Engineering 製造工程部PE Project Engineering 產品工程部--A/C Accountant Dept 會計部P/A Personal & Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部) QA Quality Assurance 品質保證(處) QC Quality Control 品質管制(課) PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Assembly 組裝(廠)S Stamping 沖壓(廠)生產類PCs Pieces 個(根,塊等) PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號OEM Original Equipment Manufacture 原設備製造PCE Personal Computer Enclosure 個人電腦外設PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器SECC SECC` 電解片SGCC SGCC 熱浸鍍鋅材料NHK North of Honking 中國大陸PRC People's Republic of China 中國大陸U.S.A the United States of America 美國A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量VS 以及--REV Revision 版本JIT Just In Time 零庫存I/O input/output 輸入/輸出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許ESD Electric-static Discharge 靜電排放5S 希臘語整理,整頓,清掃,清潔,教養ATIN Attention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk read-only Memory 只讀光碟FDD Floppy Disk Drive 軟碟機HDD Hard Disk Drive 碟碟機REF Reference 僅供參考CONN Connector 連接器CA V Cavity 模穴CAD Computer Aid Design 計算機輔助設計ASS'Y Assembly 裝配,組裝MAT'S Material 材料IC Integrated Circuit 集成電路T/P True Position 真位度TYP Type 類型WDR Weekly Delivery Requirement 周出貨需求C/T Cycle Time 制程周期L/T Lead Time 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer, Communication, Consumer electronics 消費性電子5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, message4MIH Man, Material, Money, Method, Time 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證--SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率BS Brain storming 腦力激蕩EMI Electronic Magnetic Inspect 高磁測試FMI Frequency Modulation Inspect 高頻測試B/M Board/molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system 先進的基本輸入/輸出系統CMOS Complementary Metal Oxide Semiconductor 互補金屬氧化物半導體PDA Personal Digital Assistant 個人數字助理IC Integrated Circuit 集成電路ISA Industry Standard Architecture 工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LED Light-Emitting Diode 發光二級管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金屬線緒束集組件F/C Flat Cable 排線PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WPR Weekly Delivery Requirement 周出貨要求PPM Parts Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OC Operation System 作業系統TBA To Be Design 待定,定缺--D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeIFIR (Dell Factory reject )LRR Line Reject RateSQE supplier Quality EngiweerDFM Desisw for MaFMEA Falwce modes andCIP ContinuousGVI CieBAC Vevtieal IntisntorsVCA Value Cmeuin QnaliryrISR Initial Snapple ripestPSU R owe’s SurlyFGI Forested Goal InveatoryNBE = Note Book EnclosureMPE = Mobilephone EnclosureFoxcavity = HZ = Hong ZhuiMG = maghasFoxconn = HonhaiNEW = wet work EndorserECG = electrical commercial--。