巴可放映机错误代码
巴可错误代码及处理
读取灯泡运行时间失败 灯时间读取极限失败 FCB强行灯电源关闭 冷光镜风速太高 灯电源，至少一盏灯的电源不能被检测到 3D色轮运行失败
处理方法 检查灯箱是否装好 检查灯电源线是否装好 检查冷镜风扇是否接好 检查引擎风扇是否接好 检查阳极风扇是否接好 检查阴极风扇是否接好 检查灯箱是否装好 调节镜头 检查水泵线缆接头接触，电源板 解决环境温度 解决环境温度 检查灯状况和运行时间是否超时 换灯，复位运行时间 更换灯电源 检查输入抽屉和引擎的接触或者是环境温度太低 安全认证 临时处理措施可以放映，或换板 换电源板 检查输入抽屉和引擎的接触
环境温度太低，先开热风扇吹机器然 后开机让机器预热
拔插风扇控制板或更换 抽风机风速太低 更换LPS灯电源或LPS interface板 先放一下3D片是否有效果，如没有，需更换色轮
故障中文描述 与灯箱无通信 与灯电源无通信 冷镜风扇速度低 引擎风扇速度低 阳极风扇速度低 阴极风扇速度低 灯箱未连接好 镜头位移过量 泵速度低 环境温度太高 环境温度低 关灯保护 灯超时 一个灯电源检测不到 系统错-接触不良 安全问题--需安全认证 Ti板电源自检错 Ti板电源问题 系统在警告模式下运行 TI接口板坏导致状态读取失败 TI接口板坏导致状态读取失败 TI颜色处理板坏导致状态读取失败 开灯失败 循环模式已开启 DMD蓝色温度过低 DMD绿色温度过低 DMD红色温度过低
错误代码 5004 5005 5043 5053 5073 5083 5180 5191 5212 5280 5283 5647 5657 5642 5800 5801 5802 5811 5011 5803 5804 5806 5646 5010 5293 5303 5343
Hale Waihona Puke 5654 5658 5320 5642
巴可放映机报警报错信息处理96940
巴可放映机报警报错信息处理5004 lamp---no communication 与灯箱无通信检查灯箱是否装好5005 lamp power supplies, communication failed 与灯电源无通信检查灯电源是否装好5010 pump –refill mode is on 加液模式打开退出加液模式5011 system running in restricted access mode 系统在警告模式下运行检查输入抽屉与引擎的接触5042 cold mirror fan—speed too low 冷却镜风扇转速低检查冷却镜风扇是否接好5043 cold mirror fan—speed low 冷却镜风扇转速低同上5052 engine fan –speed too low 引擎风扇转速低检查引擎风扇是否接好5062 heat exchange fan—speed too low热交换器风扇转速低检查热交换器上方风扇5063 heat exchange fan—speed low 热交换器风扇转速低同上5072 lamp anode fan –speed too low 灯阳极风扇转速低检查灯阳极风扇是否接好5073 lamp anode fan –speed low 灯阳极风扇转速低检查灯阳极风扇是否接好5082 lamp cathode fan—speed too low 灯阴极风扇转速低检查灯阴极风扇是否接好5083 lamp cathode fan—speed low 灯阴极风扇转速低检查灯阴极风扇是否接好5102 SMPS fan 1—speed too low 开关电源风扇1转速检查两个开关电源风扇5103 SMPS fan 1—speed low 开关电源风扇1转速低检查两个开关电源风扇5112 SMPS fan 2—speed too low 开关电源风扇2转速低检查两个开关电源风扇5113 SMPS fan 2—speed low 开关电源风扇2转速低检查两个开关电源风扇5122 lamp rear fan—speed too low 灯后置风扇转速低检查灯后置风扇是否接好5123 lamp rear fan—speed low 灯后置风扇转速低检查灯后置风扇是否接好5132 elca box fan—speed too low 输入-通讯单元风扇转速低检查风扇与导线的连接情况5133 elca box fan—speed low 输入-通讯单元风扇转速低检查风扇与导线的连接情况5160 engine switch—not OK 引擎安装错误检查引擎固定螺丝5170 FIB—not connected FIB未连接好检查FIB确保两个螺丝拧紧5180 lamp house—not connected 灯箱未连接好检查灯箱上的3个固定螺丝5191 prism switch —warning , lens probably touches prism镜头位移过量调节镜头5212 pump—speed too low 泵速度过低检查泵线缆接头，电源板5213 pump—speed low 泵速度偏低检查泵线缆接头，电源板5230 lens zoom position—requested target not reached 调整或更换镜头镜头变焦无法达到指定位置5231 lens focus position-- requested target not reached 调整或更换镜头镜头聚焦无法达到指定位置5232 lens horizontal shift position-- requested target not reached检查变焦马达，镜头位置镜头水平位移未达到指定位置5233 lens vertical shift position-- requested target not reached 检查变焦马达，镜头位置镜头垂直位移未达到指定位置5237 lens position—clear requested target time out failed 镜头聚焦未达到指定位置同5231 5280 ambient—temperature too high 环境温度过高请改变环境温度5281 ambient—temperature high 环境温度高请改变环境温度5283 ambient—temperature low 环境温度低请改变环境温度5284 ambient—temperature sensor open 环境温度传感器开路检查传感器和导线或更换5285 ambient—temperature sensor short 环境温度传感器短路检查传感器和导线或更换5290 DMD blue temperature too high 蓝色通道DMD温度过高检查热交换器的过滤器5291 DMD blue temperature high 蓝色通道DMD温度偏高检查热交换器的过滤器5293 DMD blue temperature low 蓝色通道DMD温度偏低光处理器单元没有启动5294 DMD blue temperature sensor open 蓝色通道DMD温度传感器开路修复导线或更换光处理器单元5295 DMD blue temperature sensor short 蓝色通道DMD温度传感器短路修复导线或更换光处理器单元5300 DMD green temperature too high 绿色通道DMD温度过高更换过滤器5301 DMD green temperature high 绿色通道DMD温度偏高更换过滤器5303 DMD green temperature low 绿色通道DMD温度偏低光处理器单元没有启动5304 DMD green temperature sensor open 绿色通道DMD温度传感器开路检查传感器和导线5305 DMD green temperature sensor short 绿色通道DMD温度传感器短路检查传感器和导线5310 lamp temperature too high 疝灯温度过高检查过滤网和抽风5311 lamp temperature high 疝灯温度偏高检查过滤网和抽风5314 lamp—temperature sensor open 疝灯温度传感器开路检查传感器和导线5315 lamp—temperature sensor short 疝灯温度传感器短路检查传感器和导线5320 FCB—force LPS off 控制板强行关闭疝灯电源在日志中查找错误信息排除5330 PFC heat-sink—temperature too high 散热器温度过高检查进气口过滤网5331 PFC heat-sink—temperature high 散热器温度偏高检查进气口过滤网5340 DMD red temperature too high 红色通道DMD温度过高检查滤网，液冷循环5341 DMD red temperature high 红色通道DMD温度偏高检查滤网，液冷循环5343 DMD red temperature low 红色通道DMD温度偏低光处理器单元没有启动5344 DMD red temperature sensor open红色通道DMD温度传感器开路检查传感器和导线5345 DMD red temperature sensor short红色通道DMD温度传感器短路检查传感器和导线5350 SMPS primary heat-sink temperature too high 开关电源主散热器温度过高检查滤网和开关电源5351 SMPS primary heat-sink temperature high 开关电源主散热器温度偏高检查滤网和开关电源5360 SMPS secondary heat-sink temperature too high 检查滤网和开关电源（开关电源次散热器温度过高）5361 SMPS secondary heat-sink temperature high 检查滤网和开关电源（开关电源次散热器温度偏高）5364 SMPS secondary heat-sink temperature sensor open 更换SMPS模块（开关电源次散热器温度传感器开路）5365 SMPS secondary heat-sink temperature sensor short 更换SMPS模块（开关电源次散热器温度传感器短路）5401 +30v—voltage high +30v电压偏高更换风扇，马达控制板5403 +30v—voltage low +30v电压偏低检查开关电源和控制板5411 ++5v—voltage high ++5v电压偏高更换风扇，马达控制板5413 ++5v—voltage low ++5v电压偏低更换风扇，马达控制板5431 cold mirror fan—voltage high 冷镜风扇电压偏高更换风扇，马达控制板5432 cold mirror fan—voltage too low 冷镜风扇电压过低更换风扇，马达控制板5433 cold mirror fan—voltage low 冷镜风扇电压偏低更换风扇，马达控制板5441 engine fan voltage high 引擎风扇电压偏高更换风扇，马达控制板5442 engine fan voltage too low 引擎风扇电压过低更换风扇，马达控制板5443 engine fan voltage low 引擎风扇电压偏低更换风扇，马达控制板5451 heat exchange fan voltage high 热交换器风扇电压偏高更换风扇，马达控制板5452 heat exchange fan voltage too low 热交换器风扇电压过低更换风扇，马达控制板5453 heat exchange fan voltage low 热交换器风扇电压偏低更换风扇，马达控制板5461 lamp anode fan voltage high 疝灯阳极风扇电压偏高更换风扇，马达控制板5462 lamp anode fan voltage too low 疝灯阳极风扇电压过低更换风扇，马达控制板5463 lamp cathode fan voltage low 疝灯阴极风扇电压低检查阴极风扇或控制板5471 lamp cathode fan voltage high 疝灯阴极风扇电压偏高更换风扇，马达控制板5472 lamp cathode fan voltage too high 疝灯阴极风扇电压过高更换风扇，马达控制板5492 SMPS fan voltage too low 开关电源风扇电压过低更换风扇，马达控制板5493 SMPS fan voltage low 开关电源风扇电压偏低更换风扇，马达控制板5501 FIB +12v voltage high +12v 电压偏高检查供电板和开关电源5502 FIB +12v voltage low +12v 电压偏低检查供电板和开关电源5521 motor ,lens ,dowser voltage high 马达镜头光闸电压高更换风扇，马达控制板5523 motor ,lens ,dowser voltage low 马达镜头光闸电压低更换风扇，马达控制板5531 pump—voltage high 泵电压偏高更换风扇，马达控制板5532 pump—voltage too low 泵电压过低更换风扇，马达控制板5533 pump—voltage low 泵电压低更换风扇，马达控制板5551 TEC voltage high TEC半导体制冷器电压高检查单元线，控制板5553 TEC voltage low TEC半导体制冷器电压低检查单元线，控制板5561 ELCA box fan voltage high ELCA box风扇电压高/检查单元线，温度传感器，控制板5563 ELCA box fan voltage low ELCA box风扇电压低/检查单元线，温度传感器，控制板5571 lamp rear fan voltage high 灯后置风扇电压高更换风扇，马达控制板5572 lamp rear fan voltage low 灯后置风扇电压低更换风扇，马达控制板5573 lamp rear fan voltage too low 灯后置风扇电压过低更换风扇，马达控制板5581 +12v voltage high +12v电压偏高更换风扇，马达控制板5583 +12v voltage low +12v电压偏低查电源板，风扇，马达控制板5640 lamp power supplies，zero lamp power supplies detected 查电源接口，换LPS模块(疝灯电源无输出)5641 lamp power supplies-- lamp is on but SMPS is off 换SMPS模块，LPS 模块（疝灯亮但开关电源关闭）5642 lamp power supplies—at least one lamp power supply could not be detected 换灯电源（一个灯电源检测不到）5643 lamp power supplies—communication failed with at least one lamp power supply(至少一个疝灯供电装置通讯失败) 重新连接两个接口，更换整个灯电源模块5644 lamp power supplies—lamp is on but at least one lamp power supply is off(疝灯点亮，但至少一个疝灯供电装置关闭) 重新连接两个接口，更换整个灯电源模块5646 lamp set on—failed 点灯失败检查灯状况，运行时间是否超时5647 lamp—lamp is off due to an error 关灯保护检查灯状况，运行时间是否超时5654 lamp run time—read failed 读取灯运行时间失败检查灯箱是否装好5657 lamp run time—exceeds maximum 灯超时换灯，复位灯运行时间5658 lamp run time—read limits failed 读取灯运行极限时间失败检查灯箱是否装好5659 lamp run time—warning 疝灯运行时间报警换灯。
巴可DP2000放映机报警报错信息处理（5篇）
巴可DP2000放映机报警报错信息处理（5篇）第一篇：巴可DP2000放映机报警报错信息处理巴可DP2000放映机报警报错信息处理5004lamp---no communication与灯箱无通信检查灯箱是否装好 5005lamp power supplies, communication failed 与灯电源无通信检查灯电源是否装好 5010pump –refill mode is on加液模式打开退出加液模式 5011system running in restricted access mode 系统在警告模式下运行检查输入抽屉与引擎的接触5042cold mirror fan—speed too low 冷却镜风扇转速低检查冷却镜风扇是否接好5043cold mirror fan—speed low冷却镜风扇转速低同上5052engine fan –speed too low引擎风扇转速低检查引擎风扇是否接好 5062heat exchange fan—speed too low热交换器风扇转速低检查热交换器上方风扇5063heat exchange fan—speedlow热交换器风扇转速低同上5072lamp anode fan –speed too low灯阳极风扇转速低检查灯阳极风扇是否接好 5073lamp anode fan –speedlow灯阳极风扇转速低检查灯阳极风扇是否接好 5082lamp cathode fan—speed too low 灯阴极风扇转速低检查灯阴极风扇是否接好5083lamp cathode fan—speedlow灯阴极风扇转速低检查灯阴极风扇是否接好5102SMPS fan 1—speed too low开关电源风扇1转速低检查两个开关电源风扇 5103SMPS fan 1—speedlow开关电源风扇1转速低检查两个开关电源风扇 5112SMPS fan 2—speed too low开关电源风扇2转速低检查两个开关电源风扇 5113SMPS fan 2—speedlow开关电源风扇2转速低检查两个开关电源风扇 5122lamp rear fan—speed too low灯后置风扇转速低检查灯后置风扇是否接好 5123lamp rear fan—speedlow灯后置风扇转速低检查灯后置风扇是否接好5132elca boxfan—speed too low 输入-通讯单元风扇转速低检查风扇与导线的连接情况 5133elca box fan—speedlow 输入-通讯单元风扇转速低检查风扇与导线的连接情况 5160engine switch—not OK引擎安装错误检查引擎固定螺丝5170FIB—not connectedFIB未连接好检查FIB确保两个螺丝拧紧 5180lamp house—not connected 灯箱未连接好检查灯箱上的3个固定螺丝5191prism switch—warning , lens probably touches prism镜头位移过量调节镜头 5212pump—speed too low泵速度过低检查泵线缆接头，电源板5213pump—speedlow泵速度偏低检查泵线缆接头，电源板5230lens zoom position—requested target not reached调整或更换镜头镜头变焦无法达到指定位置5231lens focus position--requested target not reached调整或更换镜头镜头聚焦无法达到指定位置5232lens horizontal shift position--requested target not reached检查变焦马达，镜头位置镜头水平位移未达到指定位置5233 lens vertical shift position--requested target not reached检查变焦马达，镜头位置镜头垂直位移未达到指定位置5237 lens position—clear requested target time out failed 镜头聚焦未达到指定位置同5231 5280ambient—temperature too high环境温度过高请改变环境温度5281ambient—temperaturehigh环境温度高请改变环境温度5283ambient—temperaturelow环境温度低请改变环境温度5284ambient—temperature sensor open 环境温度传感器开路检查传感器和导线或更换 5285ambient—temperature sensor short 环境温度传感器短路检查传感器和导线或更换5290DMD blue temperature too high 蓝色通道DMD温度过高检查热交换器的过滤器5291DMD blue temperaturehigh蓝色通道DMD温度偏高检查热交换器的过滤器5293DMD blue temperature low蓝色通道DMD温度偏低光处理器单元没有启动5294DMD blue temperature sensor open 蓝色通道DMD温度传感器开路修复导线或更换光处理器单元5295DMD blue temperature sensor short蓝色通道DMD温度传感器短路修复导线或更换光处理器单元5300DMD green temperature too high 绿色通道DMD温度过高更换过滤器 5301DMD green temperaturehigh绿色通道DMD温度偏高更换过滤器 5303DMD green temperaturelow绿色通道DMD 温度偏低光处理器单元没有启动5304DMD green temperature sensor open 绿色通道DMD温度传感器开路检查传感器和导线5305DMD green temperature sensor short 绿色通道DMD温度传感器短路检查传感器和导线5310lamp temperature too high疝灯温度过高检查过滤网和抽风5311lamp temperaturehigh疝灯温度偏高检查过滤网和抽风5314lamp—temperature sensor open 疝灯温度传感器开路检查传感器和导线 5315lamp—temperature sensor short 疝灯温度传感器短路检查传感器和导线 5320FCB—force LPS off控制板强行关闭疝灯电源在日志中查找错误信息排除5330PFC heat-sink—temperature too high 散热器温度过高检查进气口过滤网5331PFC heat-sink—temperaturehigh散热器温度偏高检查进气口过滤网5340DMD red temperature too high 红色通道DMD温度过高检查滤网，液冷循环5341DMD red temperaturehigh 红色通道DMD温度偏高检查滤网，液冷循环 5343DMD red temperature low红色通道DMD温度偏低光处理器单元没有启动 5344DMD red temperature sensor open红色通道DMD温度传感器开路检查传感器和导线5345DMD red temperature sensor short红色通道DMD温度传感器短路检查传感器和导线 5350SMPS primary heat-sink temperature too high 开关电源主散热器温度过高检查滤网和开关电源5351SMPS primary heat-sink temperature high 开关电源主散热器温度偏高检查滤网和开关电源5360SMPS secondary heat-sink temperature too high检查滤网和开关电源（开关电源次散热器温度过高）5361SMPS secondary heat-sink temperaturehigh检查滤网和开关电源（开关电源次散热器温度偏高）5364SMPS secondary heat-sink temperature sensor open更换SMPS模块（开关电源次散热器温度传感器开路）5365SMPS secondary heat-sink temperature sensor short更换SMPS模块（开关电源次散热器温度传感器短路）5401+30v—voltage high+30v电压偏高更换风扇，马达控制板5403+30v—voltage low+30v电压偏低检查开关电源和控制板5411++5v—voltage high++5v电压偏高更换风扇，马达控制板5413++5v—voltage low++5v电压偏低更换风扇，马达控制板5431cold mirror fan—voltage high 冷镜风扇电压偏高更换风扇，马达控制板 5432cold mirror fan—voltage too low 冷镜风扇电压过低更换风扇，马达控制板5433cold mirror fan—voltagelow冷镜风扇电压偏低更换风扇，马达控制板 5441engine fan voltage high引擎风扇电压偏高更换风扇，马达控制板5442engine fan voltage too low引擎风扇电压过低更换风扇，马达控制板 5443engine fan voltagelow引擎风扇电压偏低更换风扇，马达控制板 5451heat exchange fan voltage high 热交换器风扇电压偏高更换风扇，马达控制板 5452heat exchange fan voltage too low 热交换器风扇电压过低更换风扇，马达控制板5453heat exchange fan voltage low 热交换器风扇电压偏低更换风扇，马达控制板5461lamp anode fan voltage high疝灯阳极风扇电压偏高更换风扇，马达控制板 5462lamp anode fan voltage too low 疝灯阳极风扇电压过低更换风扇，马达控制板 5463lamp cathode fan voltage low疝灯阴极风扇电压低检查阴极风扇或控制板5471lamp cathode fan voltage high疝灯阴极风扇电压偏高更换风扇，马达控制板5472lamp cathode fan voltage too high 疝灯阴极风扇电压过高更换风扇，马达控制板 5492SMPS fan voltage too low开关电源风扇电压过低更换风扇，马达控制板 5493SMPS fan voltagelow开关电源风扇电压偏低更换风扇，马达控制板5501FIB +12v voltage high+12v 电压偏高检查供电板和开关电源5502FIB +12v voltage low+12v 电压偏低检查供电板和开关电源5521motor ,lens ,dowservoltage high马达镜头光闸电压高更换风扇，马达控制板 5523motor ,lens ,dowservoltage low马达镜头光闸电压低更换风扇，马达控制板 5531pump—voltage high泵电压偏高更换风扇，马达控制板5532pump—voltage too low泵电压过低更换风扇，马达控制板5533pump—voltagelow泵电压低更换风扇，马达控制板 5551TEC voltage highTEC半导体制冷器电压高检查单元线，控制板5553TEC voltage lowTEC半导体制冷器电压低检查单元线，控制板 5561ELCA box fan voltage highELCA box风扇电压高/检查单元线，温度传感器，控制板5563ELCA box fan voltage lowELCA box风扇电压低/检查单元线，温度传感器，控制板5571lamp rear fan voltage high灯后置风扇电压高更换风扇，马达控制板 5572lamp rear fan voltage low灯后置风扇电压低更换风扇，马达控制板 5573lamp rear fan voltage too low灯后置风扇电压过低更换风扇，马达控制板5581+12v voltage high+12v电压偏高更换风扇，马达控制板 5583+12v voltage low+12v电压偏低查电源板，风扇，马达控制板5640lamp power supplies，zero lamp power supplies detected 查电源接口，换LPS模块(疝灯电源无输出) 5641lamp power supplies--lamp is on but SMPS is off换SMPS模块，LPS 模块（疝灯亮但开关电源关闭）5642 lamp power supplies—at least one lamp power supply could not be detected 换灯电源（一个灯电源检测不到）5643 lamp power supplies—communication failed with at least one lamp power supply(至少一个疝灯供电装置通讯失败)重新连接两个接口，更换整个灯电源模块5644 lamp power supplies—lamp is on but at least one lamp power supply is off(疝灯点亮，但至少一个疝灯供电装置关闭)重新连接两个接口，更换整个灯电源模块5646lamp set on—failed点灯失败检查灯状况，运行时间是否超时 5647lamp—lamp is off due to an error关灯保护检查灯状况，运行时间是否超时 5654lamp run time—read failed读取灯运行时间失败检查灯箱是否装好5657lamp run time—exceeds maximum灯超时换灯，复位灯运行时间 5658lamp run time—read limits failed 读取灯运行极限时间失败检查灯箱是否装好 5659lamp run time—warning疝灯运行时间报警换灯第二篇：煤矿监测监控系统报警信息处理制度监测监控系统报警信息处理制度为了确保监控系统故障能够安全、有序处理，结合我矿实际情况，制订本制度，望相关单位、人员严格执行。
巴可放映机报警报错信息处理
巴可放映机报警报错信息处理5003 light sensor - no communication 光线感应器 - 无通讯5004 lamp---no communication 与灯箱无通信检查灯箱是否装好5005 lamp power supplies, communication failed 与灯电源无通信检查灯电源线缆是否装好5010 pump –refill mode is on 加液模式打开退出加液模式5011 system running in restricted access mode 系统在警告模式下运行检查输入抽屉与引擎的接触5020重新安装一下控制板的类似手机卡的卡片5041 cold mirror fan - speed high 冷镜风扇–转速偏高5042 cold mirror fan—speed too low 冷却镜风扇转速过低检查冷镜风扇及背板间连线是否接好，是否可以活动5043 cold mirror fan—speed low 冷却镜风扇转速低同上5050 engine fan - speed too high 引擎风扇转速过高5051 engine fan - speed high 引擎风扇转速偏高5052 engine fan –speed too low 引擎风扇转速低检查引擎风扇是否接好5053 engine fan - speed low 引擎风扇速度低检查引擎风扇是否接好，是否可以活动5060 heat exchanger fan - speed too high 热交换器风扇转速过高5061 heat exchanger fan - speed high 热交换器风扇转速偏高5062 heat exchange fan—speed too low 热交换器风扇转速过低检查热交换器上方风扇5063 heat exchange fan—speed low 热交换器风扇转速偏低同上5070 lamp anode fan - speed too high 灯阳极风扇转速过高5071 lamp anode fan - speed high 灯阳极风扇转速偏高5072 lamp anode fan –speed too low 灯阳极风扇转速低检查灯阳极风扇是否接好5073 lamp anode fan –speed low 灯阳极风扇转速低检查灯阳极风扇是否接好5080 lamp cathode fan - speed too high 灯阴极风扇转速过高5081 lamp cathode fan - speed high 灯阴极风扇转速偏高5082 lamp cathode fan—speed too low 灯风扇控制速度低检查风扇接头和FCB 5083 lamp cathode fan—speed low 灯阴极风扇转速低检查灯阴极风扇是否接好5100 smps fan 1 (left side) - speed too high 开关电源风扇1（左侧）转速过高5101 smps fan 1 (left side) - speed high 开关电源风扇1（左侧）转速偏高5102 SMPS fan 1—speed too low 开关电源风扇1转速过低检查两个开关电源风扇5103 SMPS fan 1—speed low 开关电源风扇1转速偏低检查两个开关电源风扇5110 smps fan 2 (right side) - speed too high 开关电源风扇2（右侧）转速过高5111 smps fan 2 (right side) - speed high 开关电源风扇2（右侧）转速过高5112 SMPS fan 2—speed too low 开关电源风扇2转速过低检查两个开关电源风扇5113 SMPS fan 2—speed low 开关电源风扇2转速偏低检查两个开关电源风扇5120 lamp rear fan - speed too high 灯后置风扇转速过高5121 lamp rear fan - speed high 灯后置风扇转速偏高5122 lamp rear fan—speed too low 灯后置风扇转速过低检查灯后置风扇是否接好5123 lamp rear fan—speed low 灯后置风扇转速偏低检查灯后置风扇是否接好5132 elca box fan—speed too low 输入通讯单元风扇转速低检查风扇与导线的连接情况5133 elca box fan—speed low 输入通讯单元风扇转速低检查风扇与导线的连接情况5140 electronics fan 1 (top side) - speed too high 电子风扇1（顶面）转速过高5141 electronics fan 1 (top side) - speed high 电子风扇1（顶面）转速偏高5142 electronics fan 1 (top side) - speed too low 电子风扇1（顶面）转速过低5143 electronics fan 1 (top side) - speed low 电子风扇1（顶面）转速偏低5150 electronics fan 2 (bottom side) - speed too high 电子风扇2（底部）转速过高5151 electronics fan 2 (bottom side) - speed high 电子风扇2（底部）转速偏高5152 electronics fan 2 (bottom side) - speed too low 电子风扇2（底部）转速过低5153 electronics fan 2 (bottom side) - speed low 电子风扇2（底部）转速偏低5160 engine switch—not OK 引擎安装错误检查引擎固定螺丝5170 FIB—not connected FIB未连接好检查FIB确保两个螺丝拧紧5180 lamp house—not connected 灯箱未连接好检查灯箱上的3个固定螺丝5190 prism switch – error 棱镜开关 - 错误5191 prism switch—warning , lens probably touches prism 镜头位移过量调节镜头5210 pump - speed too high 泵速度过高5211 pump - speed high 泵速度偏高5212 pump—speed too low 泵速度过低检查水泵线缆接头接触，SMPS电源板电压;检查泵线缆接头，电源板5213 pump—speed low 泵速度偏低检查泵线缆接头，电源板5230 lens zoom position—requested target not reached 调整或更换镜头镜头变焦无法达到指定位置5231 lens focus position-- requested target not reached 调整或更换镜头镜头聚焦无法达到指定位置5232 lens horizontal shift position-- requested target not reached 检查变焦马达，镜头位置镜头水平位移未达到指定位置5233lens vertical shift position-- requested target not reached 检查变焦马达，镜头位置镜头垂直位移未达到指定位置5237lens position—clear requested target time out failed 镜头聚焦未达到指定位置同52315250 dmd red fan - speed too high 红色通道DMD风扇转速过高5251 dmd red fan - speed high 红色通道DMD风扇转速偏高5252 dmd red fan - speed too low 红色通道DMD风扇转速太低5253 dmd red fan - speed low 红色通道DMD风扇转速偏低5260 dmd green fan - speed too high 绿色通道DMD风扇转速过高5261 dmd green fan - speed high 绿色通道DMD风扇转速偏高5262 dmd green fan - speed too low 绿色通道DMD风扇转速太低5263 dmd green fan - speed low 绿色通道DMD风扇转速偏低5270 dmd blue fan - speed too high 蓝色通道DMD风扇转速过高5271 dmd blue fan - speed high 蓝色通道DMD风扇转速偏高5272 dmd blue fan - speed too low 蓝色通道DMD风扇转速太低5273 dmd blue fan - speed low 蓝色通道DMD风扇转速偏低5280 ambient—temperature too high 环境温度过高请改变环境温度5281 ambient—temperature high 环境温度高请改变环境温度5283 ambient—temperature low 环境温度低请改变环境温度5284 ambient—temperature sensor open 环境温度传感器开路检查传感器和导线或更换5285 ambient—temperature sensor short 环境温度传感器短路检查传感器和导线或更换5290 DMD blue temperature too high 蓝色通道DMD温度过高检查热交换器的过滤器5291 DMD blue temperature high 蓝色通道DMD温度偏高检查热交换器的过滤器5293 DMD blue temperature low 蓝色通道DMD温度偏低光处理器单元没有启动5294 DMD blue temperature sensor open 蓝色通道DMD温度传感器开路修复导线或更换光处理器单元5295 DMD blue temperature sensor short蓝色通道DMD温度传感器短路修复导线或更换光处理器单元5300 DMD green temperature too high绿色通道DMD温度过高更换过滤器5301 DMD green temperature high 绿色通道DMD温度偏高更换过滤器5303 DMD green temperature low 绿色通道DMD温度偏低光处理器单元没有启动5304 DMD green temperature sensor open 绿色通道DMD温度传感器开路检查传感器和导线5305 DMD green temperature sensor short 绿色通道DMD温度传感器短路检查传感器和导线5310 lamp temperature too high 疝灯温度过高检查过滤网和抽风5311 lamp temperature high 疝灯温度偏高检查过滤网和抽风5314 lamp—temperature sensor open 疝灯温度传感器开路检查传感器和导线5315 lamp—temperature sensor short 疝灯温度传感器短路检查传感器和导线5320 FCB—force LPS off 控制板强行关闭疝灯电源在日志中查找错误信息排除5330 PFC heat-sink—temperature too high 散热器温度过高检查进气口过滤网5331 PFC heat-sink—temperature high 散热器温度偏高检查进气口过滤网5332 pfc heatsink - temperature too low PFC散热片 - 温度过低5333 pfc heatsink - temperature low PFC散热片 - 温度偏低5340 DMD red temperature too high 红色通道DMD温度过高检查滤网，液冷循环5341 DMD red temperature high 红色通道DMD温度偏高检查滤网，液冷循环5342 dmd red - temperature too low 红色通道DMD温度过低5343 DMD red temperature low 红色通道DMD温度偏低光处理器单元没有启动5344 DMD red temperature sensor open红色通道DMD温度传感器开路检查传感器和导线5345 DMD red temperature sensor short红色通道DMD温度传感器短路检查传感器和导线5350 SMPS primary heat-sink temperature too high 开关电源主散热器温度过高检查滤网和开关电源5351 SMPS primary heat-sink temperature high 开关电源主散热器温度偏高检查滤网和开关电源5352 smps primary heatsink - temperature too low 开关电源的主要散热片温度过低5353 smps primary heatsink - temperature low 开关电源的主要散热片温度偏低5360 SMPS secondary heat-sink temperature too high 检查滤网和开关电源（开关电源次散热器温度过高）5361 SMPS secondary heat-sink temperature high 检查滤网和开关电源（开关电源次散热器温度偏高）5362 smps secundary heatsink - temperature too low 开关电源次散热器温度过低5363 smps secundary heatsink - temperature low 开关电源次散热器温度偏低5364 SMPS secondary heat-sink temperature sensor open 更换SMPS模块（开关电源次散热器温度传感器开路）5365 SMPS secondary heat-sink temperature sensor short 更换SMPS模块（开关电源次散热器温度传感器短路）5370 dmd red fan - voltage too high 红色通道DMD风扇电压过高5371 dmd red fan - voltage high 红色通道DMD风扇电压偏高5372 dmd red fan - voltage too low 红色通道DMD风扇电压过低5373 dmd red fan - voltage low 红色通道DMD风扇电压偏低5380 dmd green fan - voltage too high 绿色通道DMD风扇电压过高5381 dmd green fan - voltage high 绿色通道DMD风扇电压偏高5382 dmd green fan - voltage too low 绿色通道DMD风扇电压过低5383 dmd green fan - voltage low 绿色通道DMD风扇电压偏低5390 dmd blue fan - voltage too high 蓝色通道DMD风扇电压过高5391 dmd blue fan - voltage high 蓝色通道DMD风扇电压偏高5392 dmd blue fan - voltage too low 蓝色通道DMD风扇电压过低5393 dmd blue fan - voltage low 蓝色通道DMD风扇电压偏低5401 +30v—voltage high +30v电压偏高更换风扇，马达控制板5403 +30v—voltage low +30v电压偏低检查开关电源和控制板5411 ++5v—voltage high ++5v电压偏高更换风扇，马达控制板5413 ++5v—voltage low ++5v电压偏低更换风扇，马达控制板5420 tec blue - voltage too high TEC蓝色 - 电压过高5421 tec blue - voltage high TEC蓝色 - 电压偏高5422 tec blue - voltage too low TEC蓝色 - 电压过低5423 tec blue - voltage low TEC蓝色 - 电压偏低5430 cold mirror fan - voltage too high 冷镜风扇 - 电压过高5431 cold mirror fan—voltage high 冷镜风扇电压偏高更换风扇，马达控制板5432 cold mirror fan—voltage too low 冷镜风扇电压过低更换风扇，马达控制板5433 cold mirror fan—voltage low 冷镜风扇电压偏低更换风扇，马达控制板5441 engine fan voltage high 引擎风扇电压偏高更换风扇，马达控制板5442 engine fan voltage too low 引擎风扇电压过低更换风扇，马达控制板5443 engine fan voltage low 引擎风扇电压偏低更换风扇，马达控制板5450 heat exchanger fan - voltage too high 热交换器风扇电压过高5451 heat exchange fan voltage high 热交换器风扇电压偏高更换风扇，马达控制板5452 heat exchange fan voltage too low 热交换器风扇电压过低更换风扇，马达控制板5453 heat exchange fan voltage low 热交换器风扇电压偏低更换风扇，马达控制板5460 lamp anode fan - voltage too high 疝灯阳极风扇电压过高5461 lamp anode fan voltage high 疝灯阳极风扇电压偏高更换风扇，马达控制板5462 lamp anode fan voltage too low 疝灯阳极风扇电压过低更换风扇，马达控制板5463 lamp cathode fan voltage low 疝灯阴极风扇电压低检查阴极风扇或控制板5470 lamp cathode fan - voltage too high 疝灯阴极风扇电压过高5471 lamp cathode fan voltage high 疝灯阴极风扇电压偏高更换风扇，马达控制板5472 lamp cathode fan voltage too high 疝灯阴极风扇电压过高更换风扇，马达控制板5473 lamp cathode fan - voltage low 疝灯阴极风扇电压偏低5490 smps fan - voltage too high 开关电源风扇电压过高5491 smps fan - voltage high 开关电源风扇电压偏高5492 SMPS fan voltage too low 开关电源风扇电压过低更换风扇，马达控制板5493 SMPS fan voltage low 开关电源风扇电压偏低更换风扇，马达控制板5501 FIB +12v voltage high +12v 电压偏高检查供电板和开关电源5502 FIB +12v voltage low +12v 电压偏低检查供电板和开关电源5510 tec green - voltage too high TEC绿色 - 电压过高5511 tec green - voltage high TEC绿色 - 电压偏高5512 tec green - voltage too low TEC绿色 - 电压过低5513 tec green - voltage low TEC绿色 -电压偏低5521 motor ,lens ,dowser voltage high 马达镜头光闸电压高更换风扇，马达控制板5523 motor ,lens ,dowser voltage low 马达镜头光闸电压低更换风扇，马达控制板5530 pump - voltage too high 泵电压过高5531 pump—voltage high 泵电压偏高更换风扇，马达控制板5532 pump—voltage too low 泵电压过低更换风扇，马达控制板5533 pump—voltage low 泵电压偏低更换风扇，马达控制板5540 tec red - voltage too high TEC红 - 电压过高5541 tec red - voltage high TEC红 - 电压偏高5542 tec red - voltage too low TEC红 - 电压过低5543 tec red - voltage low TEC红 - 电压偏低5550 tec - voltage too high TEC半导体制冷器电压过高5551 TEC voltage high TEC半导体制冷器电压偏高检查单元线，控制板5552 tec - voltage too low TEC半导体制冷器电压过低5553 TEC voltage low TEC半导体制冷器电压偏低检查单元线，控制板5561 ELCA box fan voltage high ELCA box风扇电压高检查单元线，温度传感器，控制板5563 ELCA box fan voltage low ELCA box风扇电压低检查单元线，温度传感器，控制板5570 lamp rear fan - voltage too high 灯后置风扇电压过高5571 lamp rear fan voltage high 灯后置风扇电压高更换风扇，马达控制板5572 lamp rear fan voltage low 灯后置风扇电压低更换风扇，马达控制板5573 lamp rear fan voltage too low 灯后置风扇电压过低更换风扇，马达控制板5581 +12v voltage high +12v电压偏高更换风扇，马达控制板5583 +12v voltage low +12v电压偏低查电源板，风扇，马达控制板5590 tec red front - voltage too high TEC红前 - 电压过高5591 tec red front - voltage high TEC红前 - 电压偏高5592 tec red front - voltage too low TEC红前 - 电压过低5593 tec red front - voltage low TEC红前 - 低电压5600 tec green front - voltage too high TEC绿色前线 - 电压过高5601 tec green front - voltage high TEC绿色前线 - 电压偏高5602 tec green front - voltage too low TEC绿色前线 - 电压过低5603 tec green front - voltage low TEC绿色前线 - 电压偏低5610 tec blue front - voltage too high TEC蓝色前 - 电压过高5611 tec blue front - voltage high TEC蓝色前 - 电压偏高5612 tec blue front - voltage too low TEC蓝色前-电压过低5613 tec blue front - voltage low TEC蓝色前 - 低电压5620 electronics fan 1 (top side) - voltage too high 电子风扇1（顶面） - 电压过高5621 electronics fan 1 (top side) - voltage high 电子风扇1（顶面） - 电压偏高5622 electronics fan 1 (top side) - voltage too low 电子风扇1（顶面） - 电压过低5623 electronics fan 1 (top side) - voltage low 电子风扇1（顶面） - 电压偏低5630 electronics fan 2 (bottom side) - voltage too high 电子风扇2（底部） - 电压过高5631 electronics fan 2 (bottom side) - voltage high 电子风扇2（底部） - 电压偏高5632 electronics fan 2 (bottom side) - voltage too low 电子风扇2（底部） - 电压过低5633 electronics fan 2 (bottom side) - voltage low 电子风扇2（底部） - 电压偏低5640 lamp power supplies，zero lamp power supplies detected 检查电源接口，换LPS模块(疝灯电源无输出)5641 lamp power supplies-- lamp is on but SMPS is off 换SMPS模块， LPS 模块（疝灯亮但开关电源关闭）5642 lamp power supplies—at least one lamp power supply could not be detected （一个灯电源检测不到）检查灯电源连线接触或更换灯或灯电源5643 lamp power supplies—communication failed with at least one lamp power supply (至少一个疝灯供电装置通讯失败) 重新连接两个接口，更换整个灯电源模块5644 lamp power supplies—lamp is on but at least one lamp power supply is off (疝灯点亮，但至少一个疝灯供电装置关闭)重新连接两个接口，更换整个灯电源模块5646 lamp set on—failed 点灯失败检查灯状况，运行时间是否超时5647 lamp—lamp is off due to an error 关灯保护检查灯状况，运行时间是否超时5654 lamp run time—read failed 读取灯运行时间失败检查灯箱是否装好5657 lamp run time—exceeds maximum灯超时换灯，复位灯运行时间5658 lamp run time—read limits failed 读取灯运行极限时间失败检查灯箱是否装好5659 lamp run time—warning 疝灯运行时间报警换灯5670 dowser - set dowser open failed dowser - 集dowser打开失败5800 ti-boards - system status = fail 系统错-接触不良检查检查输入抽屉和引擎的接触5801 ti-boards - security error, please authorize 安全问题--需安全认证进行安全认证5802 ti-boards - power up self test = fail Ti板电源自检错临时处理措施可以放映，或换板5803 ti-boards- powerup self test = fail ICP板问题5807 ti-icp - read system status failed Ti-ICP读系统状态失败刷新软件并应用克隆，或更换ICP、HDSDI输入板，刷软件5811 ti-boards - power-good = fail Ti板电源问题更换电源板5812 ti-icp - read satellite info failed Ti-ICP读信息错更换HDSDI输入板5813 ti-icp - satellite firmware mismatch Ti-ICP固件不匹配 xxB系列ICP用到xxC上，刷新ICP软件，应用克隆5814 ti-icp - self test = fail ICP 拔插ICP，升级软件并克隆5815 ti-icp - certificate error TI-ICP - 证书错误5816 ti-icp - key error TI-ICP - 关键错误5817 ti-icp - icp board not detected 没有检测到ICP板5830 TI Link decrypter - No communication TI连接解码-无通信，可以放映 Enigma接触问题，软件升级ICP到v2.1以上.或开关顺序问题，与服务器连接冲突，在服务器关闭的情况下，重启机器。
巴可投影机DP2K各类故障代码-2
代码5005 灯电源 -- 通讯失败C2 通讯电缆与通讯板的接口C3 单根的与通讯端口的连接处C 与制冷风扇的连接线错误代码5053：引擎风扇转速过低（警告）错误代码5063：热交换器风扇转速过低（警告）C 与热交换器风扇连接的供电电线C 氙灯阳极风扇连接电线FC 氙灯阴极风扇与背板供电连接线FC 与风扇连接的电线C 风扇电线连接单元错误代码 5133 elcabox 风扇转速过低（错误）C 与风扇连接的电线FZ 机动镜头聚焦马达连线LC 马达与供电背板的连线B 传感器与供电板之间的连接电线错误代码5290 ：“微镜显示蓝色 温度过高”（错误）此故障亮蓝灯，以温度过高代码显示，原因与代码5291一致SG 温度传感器前方电缆，DMD绿色通道SR 温度传感器前方电缆，DMD红色通道TB Peltier element前方电缆，DMD蓝色通道TG Peltier element前方电缆，DMD绿色通道TR Peltier element前方电缆，DMD红色通道L 位于冷循环和光输出管上方的温度传感器电缆CA 格式盘猫眼的电线SH 遮光板电缆LS 位于光输出管内的光传感器连接电缆C 将传感器与供电板连接的线路C 灯箱外连接电源背板与温度传感器的电路部分错误代码 5320：“强制切断氙灯供电”错误代码 5431：镜面冷却风扇，电压过高（警告）错误代码5451：“热交换器风扇电压过高”（警告）错误代码5452：“热交换器风扇电压过低”（错误）此故障以“热交换器风扇电压过低”报警，引起它的原因是：错误代码 5462：“氙灯阳极风扇，电压过低”（错误）此故障以“氙灯阳极风扇，电压过低”报警，引起它的原因是：错误代码 5472：“氙灯阴极风扇，电压过低”（错误）此故障以“氙灯阴极风扇，电压过低”报警，引起它的原因是：错误代码 5492：“SMPS板风扇，电压过低”（错误）此故障以“SMPS板风扇，电压过低”报警，引起它的原因是：SB 马达叶片SC 与马达的连接电缆SH 马达与格式主板连接线错误代码 5551：“TEC板电压过高”（警告）错误代码 5562：“elcabox风扇电压过低”（错误）此故障以“elcabox风扇电压过低”报警，引起它的原因是：B 与格式主板的连接线C 将归位马达与电主板连接的电缆D 将旋转马达与电主板连接的电缆S 处于光管入口的温度传感器L 该处温度传感器的连接电缆P 热管T1 处于冷却模块和DMD之间的TEC组件S2 处于TEC组件和DMD之间的温度传感器S3 处于DMD前方的温度传感器错误代码 6004：“座前，温度传感器开路”（警告）错误代码 6014：“红色道组件，温度传感器开路”（错误）R 红色道温度传感器G 绿色道温度传感器BL DMD水冷模块温度传感器FR DMD座前温度传感器E 光引擎温度传感器H 热管水冷模块温度传感器TB TEC能源供应蓝色道TG TEC能源供应绿色道TR TEC能源供应红色道BL/BT DMD水冷模块蓝色道温度传感器错误代码 7473：“氙灯阴极风扇电压过低”（警告）39页。
巴可放映机报错5800 温度高报错指导说明
5800 温度高说明文档
各位尊敬的巴可用户，当您看到放映机尾灯红色，报错5800。
首先看下触屏—诊断-当前状态
如果出现以下情况，说明ICP 温度过高，可以点击温度，进到里面看看ICP的温度，通常超过85度便会报警。
解决方案：
1.立即检查过滤网的清洁状态
2.
2.在关机断电的状态下拔出板卡检查板卡上面灰尘，以及检查板卡箱两边的风口灰尘。
3.检查灯箱的出风口，（这里最容易被忽视，也很重要）
4. 5.
总结：
通过以上的清洁，基本消除报错。
其实无非就是放映机内的热空气出不去，而冷空气无法进来，自然导致机器内温度升高。
除了以上，平时也要求放映人员主要清洁过滤网，确认放映机房的温度，让放映机“轻轻松松”的工作，它才不会出问题。
巴可放映机错误代码及处理
5807 5812 5830 5836 5835
错误描述 “lamp - no communication” “lamp power supplies - communication failed” “cold mirror fan - speed too low” “engine fan - speed too low” “lamp anode fan - speed too low” “lamp cathode fan - speed too low” “lamp house - not connected” “prism switch - warning (lens probably touches prism)” “pump - speed too low” “ambient - temperature too high” “ambient - temperature low” “lamp - lamp is off due to an error” “lamp run time - exceeds maximum” “lamp power supplies - at least one lamp power supply could not be detected” “ti-boards - system status = fail” “ti-boards - security error, please authorize” “ti-boards - power up self test = fail” “ti-boards - power-good = fail” System-running in restricted access mode Ti-boards-Interface board arm status=fail Ti-boards-interface board fpga load status=fail Ti-boards-processor board fpga load status=fail Lamp set on =faid Pump-refill mode is on Dmd blue-temperature low Dmd green-temperature low Dmd red-tempreature low Lamp run time-read failed
巴可DPK系列故障代码
BARCO DP2K系列故障代码译表本文将列举绝大部分会显示在巴可DP2K系列放映机触摸屏与日志中的故障错误代码并译文备查，同时将针对部分常见的对我放映工作有价值的故障提供解决方法。
需要注意的是，某些代码会同时表示错误和警告，某些表示错误（error），某些是警告（waring）。
在“警告”状态下，放映机虽将继续维持运转，但仍建议尽快解决导致“警报”的故障，否则，“警报”状态将有可能引发“错误”的产生，而最终导致停机事故的发生。
故障代码列表如下，可用ctrl+f快捷键进行搜索：5003: “light sensor - no communication”(Error)“灯传感器- 无通讯”5004: “lamp - no communication”(Error)“灯- 无通讯”5005: “lamp power supplies - communication failed”(Error)“灯电源- 通讯失败”5010: “pump - refill mode is on”(Warning)“冷却泵- 补充模式已开启”5042: “cold mirror fan - speed too low”(Error)“反射镜风扇- 转速过低”5043: “cold mirror fan - speed low”(Warning)“反射镜风扇- 转速低”5052: “engine fan - speed too low”(Error)“引擎风扇- 转速过低”5053: “engine fan - speed low”(Warning)“引擎风扇- 转速低”5062: “heat exchanger fan - speed too low”(Error)“散热器风扇- 转速过低”5063: “heat exchanger fan - speed low”(Warning)“散热器风扇- 转速低”5072: “lamp anode fan - speed too low”(Error)“灯阳极风扇- 转速过低”5073: “lamp anode fan - speed low”(Warning)“灯阳极风扇- 转速低”5082: “lamp cathode fan - speed too low”(Error)“灯阴极风扇- 转速过低”5083: “lamp cathode fan - speed low”(Warning)“灯阴极风扇- 转速低”5102: “smps fan 1 - speed too low”(Error)“开关电源风扇1 - 转速过低”5103: “smps fan 1 - speed low”(Warning)“开关电源风扇1 - 转速低”5112: “smps fan 2 - speed too low”(Error)“开关电源风扇2 - 转速过低”5113: “smps fan 2 - speed low”(Warning)“开关电源风扇2 - 转速低”5122: “lamp rear fan - speed too low”(Error)“灯后部风扇- 转速过低”5123: “lamp rear fan - speed low”(Warning)“灯后部风扇- 转速低”5132: “elcabox fan - speed too low”(Error)“电控盒风扇- 转速过低”5133: “elcabox fan - speed low”(Error)“电控盒风扇- 转速低”5160: “engine switch - not ok”(Error)“引擎开关- 不正常”5170: “fib - not connected”(Error)“解码板- 未连接”5180: “lamp house - not connected”(Error)“灯箱- 未连接”5191: “prism switch - warning (lens probably touches prism)”(Warning)“棱镜开关- 警告（镜头可能已触动棱镜）”5212: “pump - speed too low”(Error)“冷却泵- 转速过低”5213: “pump - speed low”(Warning)“冷却泵- 转速低”5230: “lens zoom position - requested target not reached”(Warning)“镜头变焦位置- 没有达到预定位置”5232: “lens horizontal shift position - requested target not reached”(Warning)“镜头水平移动位置- 没有达到预定位置”5233: “lens vertical shift position - requested target not reached”(Warning)“镜头垂直移动位置- 没有达到预定位置”参见52325237: “lens position - clear requested target time out failed”(Warning)“镜头位置- 接受明确指令超时”5280: “ambient - temperature too high”(Error)“环境- 环境温度过高”5281: “ambient - temperature high”(Warning)“环境- 环境温度高”参见52805283: “ambient - temperature low”(Warning)“环境- 温度低”5284: “ambient - temperature sensor open”(Error)“环境- 环境温感器断路”5285: “ambient - temperature sensor short”(Error)“环境- 环境温感器短路”5290: “dmd blue - temperature too high”(Error)“蓝DMD - 温度过高”5291: “dmd blue - temperature high”(Warning)“蓝DMD - 温度高”5293: “dmd blue - temperature low”(Warning)“蓝DMD - 温度低”5294: “dmd blue - temperature sensor open”(Error)“蓝DMD - 温感器断路”5295: “dmd blue - temperature sensor short”(Error)“蓝DMD - 温感器短路”5300: “dmd green - temperature too high”(Error)“绿DMD - 温度过高”5301: “dmd green - temperature high”(Warning)“绿DMD - 温度高”5303: “dmd green - temperature low”(Warning)“绿DMD - 温度低”5304: “dmd green - temperature sensor open”(Error)“绿DMD - 温感器断路”5305: “dmd green - temperature sensor short”(Error)“绿DMD - 温感器短路”5310: “lamp - temperature too high”(Error)“灯- 温度过高”5311: “lamp - temperature high”(Warning)“灯- 温度高”参见53105314: “lamp - temperature sensor open”(Error)“灯- 温感器断路”5315: “lamp - temperature sensor short”(Error)“灯- 温感器短路”5320: “fcb - force lps off”(Error)“风扇控制板- 灯电源强制关闭”5330: “pfc heatsink - temperature too high”(Error)“散热器- 温度过高”5331: “pfc heatsink - temperature high”(Warning)“散热器- 温度高”5340: “dmd red - temperature too high”(Error)“红DMD - 温度过高”5341: “dmd red - temperature high”(Warning)“红DMD - 温度高”5343: “dmd red - temperature low”(Warning)“红DMD - 温度低”5344: “dmd red - temperature sensor open”(Error)“红DMD - 温感器断路”5345: “dmd red - temperature sensor short”(Error)“红DMD - 温感器短路”5350: “smps primary heatsink - temperature too high”(Error)“开关电源主散热器- 温度过高”5351: “smps primary heatsink - temperature high”(Warning)“开关电源主散热器- 温度高”5360: “smps secundary heatsink - temperature too high”(Error)“开关电源副散热器- 温度过高”5361: “smps secundary heatsink - temperature high”(Warning)“开关电源副散热器- 温度过高”5364: “smps secundary heatsink - temperature sensor open”(Error)“开关电源副散热器- 温感器断路”5365: “smps secundary heatsink - temperature sensor short”(Error)“开关电源副散热器- 温感器短路”5401: “+30v - voltage high”(Warning)“+30v - 电压高”5403: “+30v - voltage low”(Warning)“+30v - 电压低”5411: “++5v - voltage high”(Warning)“++5v - 电压高”5413: “++5v - voltage low”(Warning)“++5v - 电压低”5431: “cold mirror fan - voltage high”(Warning)“反射镜风扇- 电压高”5432: “cold mirror fan - voltage too low”(Error)“反射镜风扇- 电压过低”5433: “cold mirror fan - voltage low”(Warning)“反射镜风扇- 电压低”5441: “engine fan - voltage high”(Warning)“引擎风扇- 电压高”5442: “engine fan - voltage too low”(Error)“引擎风扇- 电压过低”5443: “engine fan - voltage low”(Warning)“引擎风扇- 电压低”5451: “heat exchanger fan - voltage high”(Warning)“换热器风扇- 电压高”5452: “heat exchanger fan - voltage too low”(Error)“换热器风扇- 电压过低”5453: “heat exchanger fan - voltage low”(Warning)“换热器风扇- 电压低”5461: “lamp anode fan - voltage high”(Warning)“灯阳极风扇- 电压高”5462: “lamp anode fan - voltage too low”(Error)“灯阳极风扇- 电压过低”5463: “lamp anode fan - voltage low”(Warning)“灯阳极风扇- 电压低”5471: “lamp cathode fan - voltage high”(Warning)“灯阴极风扇- 电压高”5472: “lamp cathode fan - voltage too low”(Error)“灯阴极风扇- 电压过低”5473: “lamp cathode fan - voltage low”(Warning)“灯阴极风扇- 电压低”5492: “smps fan - voltage too low”(Error)“风扇控制板风扇- 电压过低”5493: “smps fan - voltage low”(Warning)“风扇控制板风扇- 电压低”5501: “fib +12v - voltage high”(Warning)“解码板+12v - 电压过高”5503: “fib +12v - voltage low”(Warning)“解码板+ 12v - 电压低”5521: “motor (lens, dowser) - voltage high”(Warning)“马达（镜头、光闸）- 电压高”5523: “motor (lens, dowser) - voltage low”(Warning)“马达（镜头、光闸）- 电压低”5531: “pump - voltage high”(Warning)“冷却泵- 电压高”5532: “pump - voltage too low”(Error)“冷却泵- 电压过低”5533: “pump - voltage low”(Warning)“冷却泵- 电压低”5551: “tec - voltage high”(Warning)“珀耳贴致冷器- 电压高”5553: “tec - voltage low”(Warning)“珀耳贴致冷器- 电压低”5561: “elcabox fan - voltage high”(Warning)“电控盒风扇- 电压高”5562: “elcabox fan - voltage too low”(Error)“电控盒风扇- 电压过低”5563: “elcabox fan - voltage low”(Warning)“电控盒风扇- 电压低”5571: “lamp rear fan - voltage high”(Warning)“灯后部风扇- 电压高”5572: “lamp rear fan - voltage too low”(Error)“灯后部风扇- 电压过低”5581: “+12v - voltage high”(Warning)“+12v - 电压高”5583: “+12v - voltage low”(Warning)“+12v - 电压低”5640: “lamp power supplies - zero lamp power supplies detected”(Error)“灯电源- 没有探测到灯电源”5641: “lamp power supplies - lamp is on, but smps is off”(Error)5642: “lamp power supplies - at least one lamp power supply could not be detected”(Error)参见56405643: “lamp power supplies - communication failed with at least one lamp power supply”(Error)参见56405644: “lamp power supplies - lamp is on, but at least one lamp power supply is off”(Error)参见56405646: “lamp - set lamp on failed”(Error)“灯- 点灯失败”5647: “lamp - lamp is off due to an error”(Error)“灯- 由于一个错误氙灯已熄灭”110.Code 5654: “lamp run time - read failed”(Error)“灯运行时间- 读取失败”111.Code 5657: “lamp run time - exceeds maximum”(Error)“灯运行时间- 已到最大寿命”5658: “lamp run time - read limits failed”(Error)“灯运行时间- 限制读取失败”113.Code 5659: “lamp run time - warning”(Warning)114.Code 5800: “ti-boards - system status = fail”(Error)“TI板- 系统状态=失败”这是一个通用TI错误代码，需要进入触摸屏的“诊断-测试-自检”中勾选所有选项并进行检测，并将检测结果提供给服务商用以查找具体故障所在。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
DP2K-15C
DP2K-20C
DP2K-19B
DP2K-23B
DP2K-32B
5360 5361 5362 5363 5364 5365 5370 5371 5372 5373 5380 5381 5382 5383 5390 5391 5392 5393 5420 5421 5422 5423 5430 5431 5432 5433 5440 5441 5442 5443 5450 5451 5452 5453 5460 5461 5462 5463 5470 5471 5472 5473 5490 5491 5492 5493 5510 5511 5512 5513 5530 5531 5532 5533 5540 5541 5542 5543 5550 5551 5552 5553 5570 5571 5572 5573 5590 5591 5592 5593 5600 5601 5602 5603 5610 5611 5612 5613 5620 5621 5622 5623 5630 5631 5632 5633 5640 5641 5642 5643 5644 5646 5647 5654 5657 5658 5659 5670 5800 5801 5807 5812 5813 5814 5815 5816 5817 5820 5830
Description DP2K-12C light sensor - no communication lamp - no communication lamp power supplies - communication failed pump - refill mode is on cold mirror fan - speed too high cold mirror fan - speed high cold mirror fan - speed too low cold mirror fan - speed low engine fan - speed too high engine fan - speed high engine fan - speed too low engine fan - speed low heat exchanger fan - speed too high heat exchanger fan - speed high heat exchanger fan - speed too low heat exchanger fan - speed low lamp anode fan - speed too high lamp anode fan - speed high lamp anode fan - speed too low lamp anode fan - speed low lamp cathode fan - speed too high lamp cathode fan - speed high lamp cathode fan - speed too low lamp cathode fan - speed low smps fan 1 (left side) - speed too high smps fan 1 (left side) - speed high smps fan 1 (left side) - speed too low smps fan 1 (left side) - speed low smps fan 2 (right side) - speed too high smps fan 2 (right side) - speed high smps fan 2 (right side) - speed too low smps fan 2 (right side) - speed low lamp rear fan - speed too high lamp rear fan - speed high lamp rear fan - speed too low lamp rear fan - speed low electronics fan 1 (top side) - speed too high electronics fan 1 (top side) - speed high electronics fan 1 (top side) - speed too low electronics fan 1 (top side) - speed low electronics fan 2 (bottom side) - speed too high electronics fan 2 (bottom side) - speed high electronics fan 2 (bottom side) - speed too low electronics fan 2 (bottom side) - speed low engine switch - not ok lamp house - not connected prism switch - error prism switch - warning (lens probably touches prism) pump - speed too high pump - speed high pump - speed too low pump - speed low lens zoom position - requested target not reached lens focus position - requested target not reached lens horizontal shift position - requested target not reached lens vertical shift position - requested target not reached dmd red fan - speed too high dmd red fan - speed high dmd red fan - speed too low dmd red fan - speed low dmd green fan - speed too high dmd green fan - speed high dmd green fan - speed too low dmd green fan - speed low dmd blue fan - speed too high dmd blue fan - speed high dmd blue fan - speed too low dmd blue fan - speed low ambient - temperature too high ambient - temperature high ambient - temperature too low ambient - temperature low ambient - temperature sensor open ambient - temperature sensor short dmd blue - temperature too high dmd blue - temperature high dmd blue - temperature too low dmd blue - temperature low dmd blue - temperature sensor open dmd blue - temperature sensor short dmd green - temperature too high dmd green - temperature high dmd green - temperature too low dmd green - temperature low dmd green - temperature sensor open dmd green - temperature sensor short lamp - temperature too high lamp - temperature high lamp - temperature too low lamp - temperature low lamp - temperature sensor open lamp - temperature sensor short fcb - force lps/lamp off (overtemperature, lamp house not connected or engine not connected) pfc heatsink - temperature too high pfc heatsink - temperature high pfc heatsink - temperature too low pfc heatsink - temperature low dmd red - temperature too high dmd red - temperature high dmd red - temperature too low dmd red - temperature low dmd red - temperature sensor open dmd red - temperature sensor short smps primary heatsink - temperature too high smps primary heatsink - temperature high smps primary heatsink - temperature too low smps primary heatsink - temperature low
E W E W E E E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E W E E E E E E Байду номын сангаас E N E N E E E E E E E E E E E E