5050三色RGB LED规格书
5050高亮灯珠规格书
XQD-L5DZGL-SPC1 ● Customer:Technical Data Sheet ---- Preliminary Luminosity Full Color/Single Color LED(5050 )Contents1. Features2. Applications3. Package outline dimension4. Absolute maximum ratings5. Electrical-optical characteristics6. Typical electro-optical characteristics curves7. Tapping specifications8. Package method9. BIN code description10. BIN range11. Reliability test items and conditions12. Precautions for use13. Hazard substance analysisCustomer confirm Approved by Issued ByXQD-L5DZGL-SPC1※Features.White package with black surface..Optical indicator..Colorless clear window..Ideal for backlight and light pipe application..Interior reflector..Wide viewing angle..Suitable for vapor-phase reflow, infrared reflow and wave solder processes. .Computable with automatic placement equipment..Pb-free..The product itself will remain within RoHS compliant version※Applications:.Amusement equipment..Information boards..Flashlight for digital camera of cellular phone.Device Selection GuideChip Emiteed Resin Color Type MaterialR A1GaInP Brilliant RedXQD-L5DZGL-SPC1 G InGaN Brilliant GreenB InGaN Blue※ →Package Outline Dimension:Notes: All dimensions in mm tolerance is ±0.1mm unless otherwise noted.XQD-L5DZGL-SPC1 ※Absolute Maximum Ratings(Ta=25 ℃)XQD-L5DZGL-SPC1 ※Electrical-optical characteristics(Ta=25 ℃)Note:1. Tolerance of Luminous Intensity: ±10%2. Tolerance of Dominant Wavelength: ±1nm3. Tolerance of Forward Voltage: ±0.1V※BIN rangeLuminous intensity (tolerance is ±10%@ If= 60 60mA): mA):Note:1. Tolerance of Luminous Intensity: ±10%2. Tolerance of Dominant Wavelength:±1nmXQD-L5DZGL-SPC1※Reliability test items and conditions:The reliability of products shall be satisfied with items listed below. Confidence level：90%LTPD：10%XQD-L5DZGL-SPC1 Typical Electro-Optical Characteristics Curves (G)XQD-L5DZGL-SPC1Typical Electro-Optical Characteristics Curves (R)XQD-L5DZGL-SPC1Typical Electro-Optical Characteristics Curves (B)XQD-L5DZGL-SPC1※Precautions for use ::1. Over-current-proofCustomer must apply resistors for protection; otherwise slight voltage shift will cause big current change (Burn out will happen).2. Storage2.1 Do not open moisture proof bag before the products are ready to use.2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less.2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH orless. If unused LEDs remain, it should be stored in moisture proof packages.2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded theXQD-L5DZGL-SPC1 storage time, baking treatment should be performed using the following conditions.Baking treatment: 60±5 fo℃ r 24 hours.3. Soldering Condition3.1 Pb-free solder temperature profile3.2 Reflow soldering should not be done more than twotimes.3.3 When soldering, do not put stress on the LEDs during heating.3.4 After soldering, do not warp the circuit board.Note:a) Reflow soldering should not be done more than two times.b) Don’t put stres s on the LEDs when soldering.c) Don’t warp the circuit board before it have been returned to normal ambientXQD-L5DZGL-SPC1 TemperatureTime2min, Max..5℃ /Sec. Max.4℃/Sec. Max.5 Sec. Max.260℃ Max.160~180℃TemperatureTTTTime ime120~180 sec.Preheat245 ±5℃ within 5 sec.Soldering heat Max. 260 ℃120~150℃conditions after soldering.Loaded quantity: 1000 pcs/reel※Package Method:(unit:mm)XQD-L5DZGL-SPC1Note: Tolerance unless mentioned is ±0.1mm,Unit=mm。
LC8805B-5050RGB规格书
1.2.运输及储存 Smart SMDLED采用防潮防静电铝箔袋包装，运输过程中避免挤压或刺穿包装袋，并做好必要的防静电防护措施 ，产品生产前，发现漏气及破损，请停止直接使用，并做必要的高温除湿后使用，产品在换料，贴装，成品出 货 ，安装过程中，应注意防止外力碰撞挤压 LED，造成外力损伤 LED 灯珠失效。 如生产前，已发现铝箔袋，拆封，破损，漏气请及时退回原厂重新除湿检测，绝不能上线使用。
4.封装尺寸图：
备注：所有尺寸标注单位为毫米公差为±0.15 毫米，除特别标注外。
文件编号：SPC-TOP- A/20701
PAGE: 2nd
深圳市丽创光电有限公司
Shenzhen Lictron Co.,LTD
5.引脚图及功能描述：
序号 1 2 3 4
符号 GND DIN DOUT VDD
引脚 地线或电源负端
PRODUCT NO: QUANTITY: LOT NO: DATE:
贴标签位
Lead free
标
PCS
签
示
图
注明：SMD5050 系列包装标准 1000PCS/包，特别要求除外。
文件编号：SPC-TOP- A/20701
PAGE: 8th
深圳市丽创光电有限公司
Shenzhen Lictron Co.,LTD
Smart SMD LED 属于湿敏元件，将 LED 包装在铝箔袋中是为了避免 LED 在运输和储存时吸收湿气，在包装袋中 放 有干燥剂，以吸收湿气，如果 LED 吸收了湿气，在 LED 过回流焊时，湿气就会膨胀，使胶体与支架脱离，或损 害键 合金丝，造成产品失效，由于这个原因，真空防湿包装是为了使包装袋内避免有湿气，此款产品防潮等级为 LEVEL5a。 表一：IPC/JEDEC J-STD-020 规定的材料防潮等级（MSL)定义
普朗克光电-5050RGB-IC幻彩最新规格书3-8
发光强度范围 Luminous Intensity Ranking (TA=25ºC) ：
CIE 坐标 产品型号 相关范围 CCT Part Range（K） Number CIE Coordinates Luminous intensity （mcd） @ 20mA Luminous Flux(lm) Vf@20mA Voltage (V) 发光强度 光通量Φ 正向电压
1. ±0.1V.正向电压的公差为±0.1V Tolerance of Forward Voltage is 。 2. ±15%.光通量的公差为±15% 场人员 If Ra is over 80, the brightness of products will be lower than listed below. For further informationof Ra, please consult marketing staff of Sunlight. Tolerance of Luminous Flux is 。 3. 如显色指数达80以上，产品的亮度将比上表所列略低。如对显色指数有特别要求，请咨询市
地址：深圳市宝安区石岩镇恒超工业园 A 栋 3 楼 Address：3/F, Building A, hengchao Ind.,Shiyan Town, Shenzhen China TEL：+18664985461 +86-755-29002358 FAX：+86-755-29002359 上海办事处：Shanghai Office 地址：上海市普陀区真北路 2977 弄 22 号 Address：NO.22 Lane 2977，Zhenbei Rood，Putuo District，Shanghai TEL:+86-21-36538359 Fax：+86-21-36538316
5050参数
LED SMD5050产品简介与规格参数☆产品特性1、外形尺寸：5.0×5.0×1.6mmOutline package：5.0×5.0×1.6mm2、胶体颜色：无色透明Lens appearance: Water or Yellow Clear3、发光效率和显色性高High luminous efficiency and high color display4、光谱窄，单色性好Narrow spectrum and good single color5、功耗低，精密恒流Low power consumption ,precision constant current6、硅胶封装，低衰减Silicone package ,low brightness attenuation☆产品应用1、室内室外显示屏和广告屏2、信号和指示照明Indoor or outdoor displays and billboard Signal and symbol Illumination 3、背光源4、汽车内部和尾灯照明Back lighting Interior automotive and tail lighting 5、LED日光灯和球泡灯6、LED灯条LED daylight tube and LED globe bulb LED strip☆外型尺寸图Package Outline Dimensions☆焊盘设计PAD Lay Out PCBLED SMD5050 0.2W正白最大绝对额定值Absolute maximum ratings at Ta=25度参数 Parameter 符号Symbol 值Value 单位Unit 功率耗损Power dissipation Pd 200 mW正向电流Forward current If 70 mA反向电压Reverse voltage Vr 5 V 工作温度范围Operating temperature range Topr ﹣40－﹢80 ℃贮存温度范围Storage temperature range Tstg ﹣40－﹢85 ℃最大脉冲电流Peak pulsing current Ifp 100 mA 抗静电能力Electrostatic Discharge ESD 4000 VLED SMD5050 0.2W正白光电特性Electrical optical characteristics at Ta=25度参数Parameter符号Symbol值Value单位Unit测试条件Test Conditions Min Typ Max正向电压Forward voltage VF 3.0 / 3.6 V IF=60 mA 发光强度Luminous intensity IV 3000 4500 Mcd IF=60 mA 角度Viewing angles2θ1/2 120 Dge IF=60 mA 色温Color temperature TC 5500 6500 K IF=60 mA 光通量Luminous flux/ 10 12 Lm IF=60 mA 反向电流Reverse current IR 10 μA VR=5VLED SMD5050 0.2W其他产品光电参数发光颜色Emitting Color 产品型号Model正向电压ForwardVoltage(v)正向电流ForwardCurrent(mA)色温或波段CCT(k) orWD(nm)发光强度LuminousIntensity(Mcd)角度Beanangel(°)蓝色(Blue)SY-5050-BE02 3.0—3.660 460-465600-1800 120 绿色(Green)SY-5050-GN02 3.0—3.660 520-5251800-3000 120 红色(Red )SY-5050-RD02 1.8—2.4 60 620-625800-1500 120 黄色(Yellow)SY-5050-YW02 1.8—2.4 60 585-590600-1500 120RGB SY-5050-RGB021.8—2.4 60 620-625(R)300-500 120 3.0—3.6 60 520-525(G)600-1200 120 3.0—3.6 60 460-465(B)250-600 120温馨提示：所有参数均为实验得出的统计参数，因测试设备、具体使用芯片不同，具体参数以单个产品实验数据为准。
LED5050硬灯条规格书
样品承认书SPECIFICATION FOR APPROVAL 客户名Customer品名 Product Name编号 Version number发出日期Deliver date制造确认 Product confirm and sign照明工程部照明品质部审核APPROVED BY APPROVED BY APPROVED BY检查結果□ 合格□不合格INSPECT RESULT ACCEPT REJECT客户确认Customer confirm and sign检查审核承认TESTED BY CHECKED BY APPROVED BY检查結果□ 合格□不合格INSPECT RESULT ACCEPT REJECT说明 REMARK:确认后请回传 , 谢谢 !Please confirm and fax to us ,thank you!产品规格书XL-5050LED硬灯条产品效果展示：产品名称： LED 软灯条产品型号： XL5050-60LED 硬灯条5050 灯珠效果LED 硬灯条5050 灯珠效果一、特点：1、采用高亮度SMD5050 LED灯珠，铝合金外壳，每三个LED为一段。
2、每条的标准长度为1M，每条灯珠数量分别有30PCS/M LED 灯珠，60PCS/M LED灯珠，72PCS/M LED灯珠3、发光颜色：红/ 绿 / 蓝 / 黄 / 白 / 暖白和长彩等多种颜色可供选择4、工作电压：DC12V/DC24V两种5、防水型SMD灯条，表面采用灌胶二、用途：1、 SMD高亮度硬灯条适用于酒店，超薄灯箱，KTV娱乐场所等室内装饰。
2、用于广告招牌等精品装饰领域。
3、度假装饰照明灯，显示及展览。
4、商场专柜，珠宝，首饰台及名贵钟表柜台。
三、产品规格：1 米 30 珠型号规格产品规格书型号颜色XL-5050-30-R 红XL-5050-30-G 绿XL-5050-30-B 蓝XL-5050-30-Y 黄XL-5050-30-W 白XL-5050-30-WW 暖白XL-5050-30-RGB RGB1 米 60 珠型号规格型号颜色XL-5050-60-R 红XL-5050-60-G 绿XL-5050-60-B 蓝XL-5050-60-Y 黄XL-5050-60-W 白XL-5050-60-WW 暖白XL-5050-60- RGB RGB1 米 72 珠型号规格型号颜色XL-5050-72-R 红XL-5050-72-G 绿XL-5050-72-B 蓝XL-5050-72-Y 黄XL-5050-72-W 白XL-5050-72-WW 暖白XL-5050-72- RGB RGB产品名称： LED 软灯条产品型号： XL5050-60 电压数量功率DC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2W电压数量功率DC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4W电压数量功率DC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2W四、参数序号项目 item 单位参数范围 Parameter range1 工作环境温度 working environment ℃-40~502 储存条件 storage condition ℃-50~604 额定电压 limited voltage V DC125 工作电流 current mA 206 功耗 Input power W 7． 2W / 14.4W / 17.2W灯珠类型号：SMD 5050 LED可选颜色：红/绿/蓝/黄/白/暖白/RGB发光角度 : 120 度灯珠数量:30PCS / M60PCS / M72PCS / M外形尺寸 : 1000*10*2mm按整体封存装:裸板V 型槽U 型槽硬灯条套 V 型槽图示硬灯条裸板图示U型槽图示五、注意事项：六、产品应用应用家居装饰应用 KTV 装饰珠宝柜装饰●使用说明 use manual:1. 请先仔细阅读产品规格书 ,确认其使用环境是否符合规格书上的条件上,方可放心使用 . Please read the specificationfirst to make sure the using condition is fit2. 将产品接入电源时 ,请先确保开关处于闭合状态 ..Please shut off the switch before connect the product, then turn on3.本产品保质期为一年 This product warranty for one year。
布里德拉克斯SMD 5050系列强力LED数据手册说明书
Product Data Sheet DS69The Bridgelux SMD 5050 Gen2 high power LED is hot-color targeted, which ensures that the LEDs fall within their specified color bin at the typical application conditions of 85°C. With its broad lumen coverage and wide range of CCT options, the SMD 5050 provides unparalleled design-in flexibility for indoor and outdoor lighting applications. The SMD 5050 is ideal as a drop-in replacement for emitters with an industry standard 5.0mm x 5.0mm footprint.Features• Industry-standard 5050 footprint• 3 bin color control enables tight color control• Hot-color targeting ensures that color is within the ANSI bin at the typical application conditions of 85°C • Enables 3- and 5-step MacAdam ellipse custom binning kits• RoHS compliant and lead free• Multiple CCT configurations for a wide range of lighting applicationsBenefits• Lower operating and manufacturing cost• Ease of design and rapid go-to-market• Uniform consistent white light• Reliable and constant white point• Environmentally friendly, complies with standards • Design flexibilityContentsProduct Feature MapProduct NomenclatureThe part number designation for Bridgelux SMD 5050 is explained as follows:Product Test ConditionsBridgelux SMD 5050 Gen2 LEDs are tested and binned with a 10ms pulse of 125mA at T j (junction temperature)=T sp (solder point temperature) =25°C. Forward voltage and luminous flux are binned at a T j =T sp =25°C, while color is hot targeted at a T sp of 85°C.Bridgelux SMD LED products come in industry standard package sizes and follow ANSI binning standards. These LEDs are optimized for cost and performance, helping to ensure highly competitive system lumen per dollar performance while addressing the stringent efficacy and reliability standards required for modern lighting applications.1 2 3 4 5 6 7 8 9 10 11 12 1314 15 16Product FamilyColor Bin OptionsFlux BinsMinimum CRIC = 70 CRI E = 80 CRI G = 90 CRIForward Voltage Bins Nominal CCT27 = 2,700K 30 = 3,000K 35 = 3,500K 40 = 4,000K 45 = 4,500K 50 = 5,000K 57 = 5,700K 65 = 6,500KBXEP – 30 E – 1 C 5 – 36 B – 00 – 00 – oProduct VersionPower 5 = 4.4W Die count in parallelTypical Forward VoltageDie count in series Yellow phosphor Light Emitting Surface (LES)Cathode MarkProduct Selection GuideThe following product configurations are available:Table 1: S election Guide, Pulsed Measurement Data at 125mA (T j =T sp =25°C)Notes for Table 1:1. The last 7 characters (including hyphens ‘-’) refer to flux bins, forward voltage bins, and color bin options, respectively. “00-00-0” denotes the full distribution of flux, forward voltage, and 7 SDCM color. Example: B XEP-30E-1C5-36B-00-00-0 refers to the full distribution of flux, forward voltage, and color within a 3000K 7-step ANSI standard chromaticity region with a minimum of 80CRI, 1x12 die configuration, 4.4w power, 35.5V typical forward voltage.2. Product CCT is hot targeted at T sp = 85°C. Nominal CCT as defined by ANSI C78.377-2011.3. Listed CRIs are minimum values and include test tolerance.4. Products tested under pulsed condition (10ms pulse width) at nominal drive current where T j =T sp =25°C.5. Bridgelux maintains a ±7.5% tolerance on luminous flux measurements, ±0.1V tolerance on forward voltage measurements, and ±2 tolerance on CRI measurements for the SMD 5050 Gen2.6. Refer to Table 6 and Table 7 for Bridgelux SMD 5050 Gen2 Luminous Flux Binning and Forward Voltage Binning information.Product Selection GuideThe following product configurations are available:Notes for Table 2:1. The last 7 characters (including hyphens ‘-’) refer to flux bins, forward voltage bins, and color bin options, respectively. “00-00-0” denotes the full distribution of flux, forward voltage, and 7 SDCM color. Example: B XEP-30E-1C5-36B-00-00-0 refers to the full distribution of flux, forward voltage, and color within a 3000K 7-step ANSI standard chromaticity region with a minimum of 80CRI, 1x12 die configuration, 4.4w power, 35.5V typical forward voltage.2. Product CCT is hot targeted at T sp = 85°C. Nominal CCT as defined by ANSI C78.377-2011.3. Listed CRIs are minimum values and include test tolerance.4. Bridgelux maintains a ±7.5% tolerance on luminous flux measurements, ±0.1V tolerance on forward voltage measurements, and ±2 tolerance on CRI measurements for the SMD 5050 Gen2.5. Refer to Table 6 and Table 7 for Bridgelux SMD 5050 Gen2 Luminous Flux Binning and Forward Voltage Binning information.6. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.7. Typical performance is estimated based on operation under DC (direct current) with LED emitter mounted onto a heat sink with thermal interfacematerial and the solder point temperature maintained at 85°C. Based on Bridgelux test setup, values may vary depending on the thermal design of the luminaire and/or the exposed environment to which the product is subjected.Table 2: Selection Guide, Stabilized DC Performan ce (T sp = 85°C)6,7Table 3:Performance at Commonly Used Drive CurrentsSMD 5050 LEDs are tested to the specifications shown using the nominal drive currents in Table 1. SMD 5050 may also be driven at other drive currents dependent on specific application design requirements. The performance at any drive current can be derived from the current vs. voltage characteristics shown in Figure 2 and the relative luminous flux vs. current characteristics shown in Figure 3. The performance at commonly used drive currents is summarized in Table 3.Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Table 3:Performance at Commonly Used Drive CurrentsSMD 5050 LEDs are tested to the specifications shown using the nominal drive currents in Table 1. SMD 5050 may also be driven at other drive currents dependent on specific application design requirements. The performance at any drive current can be derived from the current vs. voltage characteristics shown in Figure 2 and the relative luminous flux vs. current characteristics shown in Figure 3. The performance at commonly used drive currents is summarized in Table 3.Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Table 3:Performance at Commonly Used Drive Currents(Continued)Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Table 3:Performance at Commonly Used Drive Currents (Continued)Notes for Table 3:1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Electrical CharacteristicsNotes for Table 4:1. The last 7 characters (including hyphens ‘-’) refer to flux bins, forward voltage bins, and color bin options, respectively. “00-00-0” denotes the full distribution of flux, forward voltage, and 7 SDCM color. Example: B XEP-30E-1C5-36B-00-00-0 refers to the full distribution of flux, forward voltage, and color within a 3000K 7-step ANSI standard chromaticity region with a minimum of 80CRI, 1x12 die configuration, 4.4w power, 35.5V typical forward voltage.2. Bridgelux maintains a tolerance of ± 0.1V on forward voltage measurements. Voltage minimum and maximum values at the nominal drive current are guaranteed by 100% test.3. Products tested under pulsed condition (10ms pulse width) at nominal drive current where T sp = 25°C.4. Thermal resistance value was calculated using total electrical input power; optical power was not subtracted from input power.Table 4: Electrical CharacteristicsAbsolute Maximum RatingsTable 5: Maximum RatingsNotes for Table 5:1. The condition of the maximum drive current is limited, Figure 7 can be reference.2. Bridgelux recommends a maximum duty cycle of 10% and pulse width of 10 ms when operating LED SMD at maximum peak pulsed current specified.Maximum peak pulsed current indicate values where LED SMD can be driven without catastrophic failures.3. The maximum drive current for LM80 test result is based on 128% nominal drive current listed.Table 6: Luminous Flux Bin Definitions at 125mA, T sp=25°CTable 6 lists the standard photometric luminous flux bins for Bridgelux SMD 5050 LEDs. Although several bins are listed, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs.Table 7: Forward Voltage Bin Definition at 125mA, T sp=25°CNote for Table 7:1. Bridgelux maintains a tolerance of ± 0.1V on forward voltage measurements.Note for Table 6:1. Bridgelux maintains a tolerance of ± 7.5% on luminous flux measurements.Table 8: 3- and 5-step MacAdam Ellipse Color Bin DefinitionsNotes for Table 8:1. Color binning at T sp =85°C2.Bridgelux maintains a tolerance of ± 0.007 on x and y color coordinates in the CIE 1931 color space.Figure 1: C.I.E. 1931 Chromaticity Diagram (3 Color Bin Structure, hot-color targeted at T=85°C)spNote for Figure 3:1. Bridgelux does not recommend driving high power LEDs at low currents. Doing so may produce unpredictable results. Pulse width modulation (PWM) is recommended for dimming effects.Figure 2: Drive Current vs. Voltage (T sp =25°C)Figure 3: Typical Relative Luminous Flux vs. Drive Current (T sp =25°C)Figure 4: Typical Relative DC Flux vs. Solder Point TemperatureFigure 5: Typical DC ccx Shift vs. Solder Point TemperatureNotes for Figures 4 & 5:1. Characteristics shown for warm white based on 2700K and 80 CRI.2. Characteristics shown for neutral white based on 4000K and 80 CRI.3. Characteristics shown for cool white based on 5700K and 80 CRI.4. For other color SKUs, the shift in color will vary. Please contact your Bridgelux Sales Representative for more information.Figure 6: Typical DC ccy Shift vs. Solder Point TemperatureNotes for Figure 6:1. Characteristics shown for warm white based on 2700K and 80 CRI.2. Characteristics shown for neutral white based on 4000K and 80 CRI.3. Characteristics shown for cool white based on 5700K and 80 CRI.4. For other color SKUs, the shift in color will vary. Please contact your Bridgelux Sales Representative for more information. Figure 7: Drive Current Derating CurveTypical Radiation PatternFigure 8: Typical Spatial Radiation Pattern at 125mA, T sp =25°CFigure 9: Typical Polar Radiation Pattern at 125mA, T sp =25°CNotes for Figure 8:1. Typical viewing angle is 116⁰.2.The viewing angle is defined as the off axis angle from the centerline where luminous intensity (Iv) is ½ of the peak value.Typical Color Spectrum Figure 10: Typical Color SpectrumNotes for Figure 10:= 25°C1. Color spectra measured at nominal current for Tsp2. Color spectra shown for warm white is 2700K and 80 CRI.3. Color spectra shown for neutral white is 4000K and 80 CRI.4. Color spectra shown for cool white is 5700K and 80 CRI.Mechanical DimensionsFigure 11: Drawing for SMD 5050Notes for Figure 11:1. Drawings are not to scale.2. Drawing dimensions are in millimeters.3. Unless otherwise specified, tolerances are ± 0.10mm.Recommended PCB Soldering Pad PatternReliabilityTable 9: Reliability Test Items and ConditionsNotes for Table 9:1. Measurements are performed after allowing the LEDs to return to room temperature2. T sld : reflow soldering temperature; T a: ambient temperaturePassing CriteriaFigure 12 :Reflow ProfileReflowing CharacteristicsFigure 13 : Pick and PlaceNote for Figure 13:1. When using a pick and place machine, choose a nozzle that has a larger diameter than the LED’s emitting surface. Using a Pick-and-Place nozzle witha smaller diameter than the size of the LEDs emitting surface will cause damage and may also cause the LED to not illuminate.Is greater than LEDsemitting surfaceFigure 14: Emitter Reel DrawingsNote for Figure 14:1. Drawings are not to scale. Drawing dimensions are in millimeters. Figure 15: Emitter Tape DrawingsNote for Figure 15:1. Drawings are not to scale. Drawing dimensions are in millimeters.Figure 16: Emitter Reel Packaging DrawingsNote for Figure 16:1. Drawings are not to scale.Design ResourcesDisclaimersPrecautionsPlease contact your Bridgelux sales representative for assistance.MINOR PRODUCT CHANGE POLICYThe rigorous qualification testing on products offered by Bridgelux provides performance assurance. Slight cosmetic changes that do not affect form, fit, or function may occur as Bridgelux continues product optimization.CAUTION: CHEMICAL EXPOSURE HAZARDExposure to some chemicals commonly used in luminaire manufacturing and assembly can cause damage to the LED emitter. Please consult Bridgelux Application Note AN51 for additional information.CAUTION: EYE SAFETYThis SMD package emits visible light, that, under certain circumstances, could be harmful to the eye. Proper safe -guards must be used.CAUTION: RISK OF BURNDo not touch the SMD LED emitter during operation. Allow the emitter to cool for a sufficient period of time before handling. The SMD LED emitter may reachelevated temperatures such that could burn skin when touched.CAUTIONCONTACT WITH LIGHT EMITTING SURFACE (LES) Avoid any contact with the LES. Do not touch the LES of the emitter or apply stress to the LES (yellow phosphor resin area). Contact may cause damage to the emitterOptics and reflectors must not be mounted in contact with the LES (yellow phosphor resin area).STANDARD TEST CONDITIONSUnless otherwise stated, LED emitter testing is performed at the nominal drive current.About Bridgelux: We Build Light That Transforms© 2018 Bridgelux, Inc. All rights reserved 2018. Product specifications are subject to change without notice. Bridgelux and the Bridgelux stylized logo design are registered trademarks of Bridgelux, Inc. All other trademarks are the property of their respective owners.46430 Fremont Boulevard Fremont, CA 94538Tel (925) At Bridgelux, we help companies, industries and people experience the power and possibility of light. Since 2002, we’ve designed LED solutions that are high performing, energy efficient, cost effective and easy to integrate. Our focus is on light’s impact on human behavior, delivering products that create better environments, experiences and returns—both experiential and financial. And our patented technology drives new platforms for commercial and industrial luminaires.For more information about the company, please visit /Bridgelux /Bridgelux/user/Bridgelux WeChat ID: BridgeluxInChina。
5050三色RGBLED规格书
5050三色RGBLED规格书承認書Samples approval sheet客戶名稱（Customer name）：元件名稱（Production name）：發光二極體型號（Model）：RGB5050編號（Part number）：日期（Date）：2013-11-22編制Prepared by審核Checked by核准Approved by市場部Market Dept.客戶確認CUSTOMER CONFIRMATION確認Confirmed by審核Checked by核准Approved by一、外形圖Outline dimensions：單位Unit公差Tolerance晶片材料Die material膠體顏色Lens color發光顏色Emission colormm ±0.2mm ---- --※備註：承認書之編號和型號可用于查詢，客戶如有需要，請提供相應的編號和型號。
Remark：P/N & Model in samples approval sheet can be used to inquire，please provide corresponding P/N& model if customer need .二、光電參數Photoelectricity Parameter（環境溫度Ambient temperature：25℃濕度humidity：RH60%）項目Item符號Symbol測試條件Testcondition最小值Min典型值Type最大值Max單位Unit正向電壓Forward voltage VF IF=20mA R 1．9 -- 2．1V IF=20mA G 3．0 -- 3.3IF=20mA B 3．0 -- 3.3反向電流Reverse current IR VR=5V -- -- 10 μA發光強度Luminous intensity IV IF=20mA R 700 -- 900MCD IF=20mA G 1500 -- 1700IF=20mA B 500 -- 700主波長Dominant wavelengthλd IF=20mA R 620 -- 625nm IF=20mA G 520 523 525IF=20mA B 460 462 465光譜半寬度Spectrum line half widthΔλIF=20mA -- 60 -- nm 視角Viewing Angle2θ1/2 IF=20mA -- 120 -- deg備註：亮度測試公差±15%、波長測試公差±1nm、正向電壓測試公差±0.05V Remark：The tolerance of intensity:±15%, The tolerance of wave length:±1nm,The tolerance of forwards voltage: ±0.05V. Only reference for above data when testing.三、極限參數Absolute Maximum Rating（環境溫度Ambient temperature：25℃濕度humidity：RH60%）項目Item符號Symbol數值Value單位Unit備註Remark正向電流Forward Current IF 20 mA ---正向峰值電流Peck forward currentIFM 75 mA F=1KHZ,占空比(duty cycle)1/10反向耐壓Reverse Voltage VR 15 V --- 耗散功率Power DissipationPm 80 mW ---工作環境溫度OperationtemperatureTamb -25至+80 ℃--- 貯藏溫度Storage temperatureTstg +40至+60 ℃---焊接溫度Solderin g temperature Tsol 240 ℃焊接,≤3SSoldering,≤3S型號Model：RGB5050頁碼Page： 3/4四、典型光電特性曲線圖T ypical photoelectricity characteristic curve chart型號Model：RGB5050頁碼Page： 4/4R 五、可靠性實驗項目Reliability Test Project判斷標準Judging criterion:項目 Item符號 Symbol實驗條件 Experiment condition判斷標準CriteriaMin.Max.Forward V oltage V F I F =20mA ---- Initial Datex1.1Reverse Current I R V R =5V ---- 30μA Luminous IntensityIVI F =20mAInitial Datex0.8----描述 Description 項目 Item測試標準 T est criterion 測試條件 T est condition 測試時間 T est time 數量 Qty 失效數量 Fail qty 壽命測試 Life test常溫壽命測試Life test(room temperature) JIS7021:B4 T a=25℃±5℃，IF=30mA1000Hrs22環境測試 Ambience test高溫存儲High temperature store JIS7021:B10 MIL-STD-202:210A MIL-STD-750:2031 T a=85℃±5℃ 1000Hrs 22 0低溫存儲Low temperature storeJIS7021:B12 T a= -35℃±5℃ 1000Hrs 22 0 高溫高濕測試High temperature/ humidity testJIS7021:B11 MIL-STD-202:103D T a=85℃±5℃ RH=85% 1000Hrs22冷熱衝擊測試Cold / Heat strike test JIS7021::B4 MIL-STD-202:107D MIL-STD-750:102630min-10℃±5℃←→100℃±5℃ 5min 5min50Cycles 22 0冷熱迴圈測試Cold and heat cycle testJIS7021:A3 MIL-STD-202:107D MIL-STD-705:105E 5min 5min 5min -35℃～25℃～85℃～-35℃ 30min 5min 30min 5min 50Cycles 22 0。
LA-5050RGB-A LED说明书
LA-5050RGB-A●目录：（Content）◆封面:(Cover)━‥━‥━‥━‥━‥━‥━‥━‥━‥‥━‥━‥PAGE:1OF12◆产品简介(Product introduction)━‥━‥━‥━‥━‥━‥‥━‥━‥PAGE:2OF12◆外形尺寸图及应用领域(Outline Dimensions)━‥━‥━‥━‥━‥━PAGE:3OF12◆产品编码解说及光电参数：Electrical-Optical Characteristics━‥━‥PAGE:4OF12◆色区分BIN及色温坐标：（Intensity Bin Limit）━‥━‥‥━‥━‥━PAGE:5OF12◆光电特性曲线图：（Optical Characteristics）━‥━‥━‥━‥━‥━‥PAGE:7OF12◆信赖度测试项目及标准：（Test items and results of reliability）‥‥‥PAGE:8OF12◆包装规范：（Packing）━‥━‥━━‥━‥━━‥━‥━‥━‥━‥━‥PAGE:9OF12◆产品使用说明及注意事项:(Usage and Handling Instructions)‥‥‥PAGE:10-12OF12●特性：（Features）◆ 5.4长*5.0宽*1.6高：（5.4mm*5.0mm*1.6mm SMT LED Thickness.）◆角度：120度：（View Anglc:120°）◆包装：1000/一盒：（Package：1000PCS/Packet）◆发光颜色：RGB（Emitted Color:RGB）◆混色型：（Mono-color type）◆工作温度：-40～80度：（Operating Temperature:-40～+80℃）◆焊接温度：260度10秒：（S oldering Temperature：260for10sec℃）◆超大功率：（Supper High Power Consumption）◆可做不同的种类：（Various Colors And Types Available.）◆胶水：硅胶：（Resin(Mold):Silicone）◆反向电压5V：（Reverse Voltage:5V）◆储存温度-40～+100度：（Storage Temperature:-40～+100℃）◆脉冲电流60mA注：脉冲宽度0.1mS占空比1/10Pulsed Forward Current60mA(Duty1/10,Pulse Width0.1mS.）LA-5050RGB-ALA-5050RGB-ALA-5050RGB-A●分BIN参数：（Color Coordinate Comparison）·色坐标范围LA-5050RGB-A●典型光学特性曲线：（Typical optical characteristics curves）环境温度与正向电流特性曲线正向电流与相对光强特性曲线Ambient Temperature vs.Forward Current Forward Current VS.Relative Intensity正向电压与正向电流特性曲线环境温度与相对光强特性曲线Forward Voltage VS.Forward Current Ambient Temperature VS.Relative Intensity相对光谱分布特性曲线辐射图特性曲线Relative spectral emission Radiation diagramLA-5050RGB-ALA-5050RGB-A●包装规格✧标签：（Label）卷轴尺寸：（Reel Dimensions）✧载带规格（单位：mm):（Tape Specifications(Units:mm）✧防潮带包装：（Moisture Resistant Packaging）注：标注公差为±0.1mm，单位：mm：（Note:The tolerances unless mentioned is±0.1mm,Unit:mm）LA-5050RGB-A●回流焊接曲线图（IR reflow soldering Profile）✧有铅焊接（Lead solder）✧无铅焊接（Lead Free solder）注意：（NOTES：）1.我们建议的回流焊温度为240℃±5℃，最高的焊接温度要控制在260℃以内。
5050RGB规格书(中文)
标示区有无由蓝色变为粉红色.如漏气或变色现象,请联系厂家或退回厂家高温除湿处理,(高温除湿 环境：120 度，6H)切勿自行处理 2-2. 打开包装前， LEDs 需储存在温度低于 30℃，湿度低于 70%RH 。 2-3. 打开包装后，在温度低于 30℃ ，湿度低于 60%RH 的情况下，且开封到焊接完成控制在 4H。 2-4. 如果吸湿材料 (硅凝胶)已经消退或是 LEDs 已经超过了储存时间, 则需要基于以下条件进行烘烤 处理： 60±5℃ / 24 小时。 3. 回流焊注意事项 3-1. 无铅锡膏的温度曲线
█ 电性与光学特性(Ta=25℃)
参数 正向电压 反向电流 发光角度 波长
光通量
符号
条件
最小 平均 最大 单位
R IF=20mA
2.0
--
2.3
VF G IF=20mA
2.9
--
3.2
V
B IF=20mA
2.9
--
3.2
IR
VR=5V
--
--
5
μA
2θ1/2
IF=3*20mA
--
120
--
deg
R IF=20mA
3-2. 回流焊不能超过两次。 3-3. 焊接期间, 加热时不要在 LEDs 上添加任何压力。 3-4. 焊接后, 正常回温至 40℃以下后才可过电流。 4. 防护措施
用适当的工具从材料侧面夹取，因产品使用硅胶封装避免在应用过程中压伤胶体，损伤内部结构造
成不良。LED 为半导体敏感器件，静电放电（ESD）或脉冲电流（EOS）可能会损害 LED。 作业机台 有效接地、作业中作好静电防护，可有效提升产品品质。贴片 LED 灯珠在生产过程中及灯具使用环境 需避免与硫.卤素.酸.醇.碱.酮肟类挥发性化合物,强氧化物.增塑剂(又名塑化剂,领苯二甲酸二辛酯 DOP 或邻苯二甲酸二丁酯 DBP,PVC 物料即含有大量增塑剂)等腐蚀性物质接触
5050RGB声控灯条规格书
使用本产品之前，敬请仔细阅读本手册，确保完全理解本规格书以避免不必要的损坏和额外的费用。
产品简介LED RGB声控灯条采用先进的PWM控制技术，能够实现多钟RGB颜色变化（详细模式见下文）；采用RF无线射频遥控进行模式选择调节，实现静态、跳变、渐变和音频感应等灯光变化效果，同时客户可根据实际需求对静态颜色进行亮度调节，对动态变化进行速度调节；该款产品是基于音频分析技术和更人性化遥控器设计基础上进行升级的第二代音乐控制器,达到完美的音频控制效果和用户体验；并可以与本公司的RGB信号放大器进行功率扩展，实现更多LED灯的同步化，理论上可以连接无数个RGB放大器。
技术参数工作温度-20-60℃供电电压12~24V静态功耗<1W连接方式共阳灰度级256级（可连发）速度档100级（可连发）净重185g毛重215g外型尺寸L130ΧW64ΧH24 mm包装尺寸L137ΧW80ΧH54 mm输出3回路输出电流≤4A(每回路)遥控方式RF发射接收频率433.92Mhz遥控距离20m模式14种控制器输出功率12V:≤144W产品特点1、产品供电电压12V电压；2、输出为三回路，每路允许最大电流为4A，能带12V30灯/米的灯带20米，12V60灯/米的灯带10米；3、采用RF无线遥控方式，具有遥控距离远，无方向性，可穿透一定厚度阻碍物等特点，环境的不同，最大距离可以达到20米；常规产品的无线遥控器是可通用的，如需要一对一控制，需要对其编码；4、具有断电记忆存储功能，每次上电都会保留上次掉电时的变化模式；5、14种模式，包括8种静态颜色、3种动态变化和3种音乐模式，其中3种音乐模式分别对应F.T.:DJ(快节奏变化)、M.T.:动感(通用型的节奏变化)、C.T.:柔情(慢节奏变化)；音频模式时可通过黑色旋钮调节灵敏度；6、音频控制可以通过麦克风和音频线输入信号两种方法实现;7、为了实现更多灯具的同步，可与本公司的RGB信号放大器进行功率扩展。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
22
0
環境測試
Ambience
test
高溫存儲
High temperature store
JIS7021:B10
MIL-STD-202:210A
MIL-STD-750:2031
Ta=85℃±5℃
1000Hrs
22
0
低溫存儲
Low temperature store
JIS7021:B12
Tstg
+40至+60
℃
---
焊接溫度
Soldering temperature
Tsol
240
℃
焊接,≤3S
Soldering,≤3S
型號Model：
四、典型光電特性曲線圖Typicalphotoelectricity characteristic curve chart
型號Model：
●R五、可靠性實驗項目Reliability Test Project
VF
IF=20mA
R
1．9
--
2．1
V
IF=20mA
G
3．0
--
3.3
IF=20mA
B
3．0
--
3.3
反向電流Reverse current
IR
VR=5V
--
--
10
μA
發光強度Luminous intensity
IV
IF=20mA
R
700
--
900
MCD
IF=20mA
G
1500
--
1700
IF=20mA
----
Initial Datex1.1
Reverse Current
IR
VR=5V
----
30μA
Luminous Intensity
IV
IF=20mA
Initial Datex0.8
----
B
500
--
700
主波長Dominant wavelength
λd
IF=20mA
R
620
--
625
nm
IF=20mA
G
520
523
525
IF=20mA
B
460
462
465
光譜半寬度
Spectrum line half width
Δλ
IF=20mA
--
60
--
nm
視角Viewing Angle
2θ1/2
IFM
75
mA
F=1KHZ,占空比(duty cycle)1/10
反向耐壓
Reverse Voltage
VR
15
---
耗散功率
Power Dissipation
Pm
80
mW
---
工作環境溫度Operation temperature
Tamb
-25至+80
℃
---
貯藏溫度
Storage temperature
承認書
Samples approval sheet
客戶名稱（Customer name）：
元件名稱（Production name）：發光二極體
型號（Model）：RGB5050
編號（Part number）：
日期（Date）：2013-11-22
編制
Prepared by
審核
Checked by
核准
Ta= -35℃±5℃
1000Hrs
22
0
高溫高濕測試
High temperature/ humidity test
JIS7021:B11
MIL-STD-202:103D
Ta=85℃±5℃
RH=85%
1000Hrs
22
0
冷熱衝擊測試
Cold / Heat strike test
JIS7021::B4
MIL-STD-202:107D
MIL-STD-750:1026
30min
-10℃±5℃←→100℃±5℃
5min 5min
50Cycles
22
0
冷熱迴圈測試
Cold and heat cycle test
JIS7021:A3
MIL-STD-202:107D
MIL-STD-705:105E
5min 5min 5min
-35℃～25℃～85℃～-35℃
30min 5min 30min 5min
50Cycles
22
0
●
判斷標準Judging criterion:
項目
Item
符號
Symbol
實驗條件
Experiment condition
判斷標準
Criteria
Min.
Max.
Forward Voltage
VF
IF=20mA
三、極限參數Absolute Maximum Rating（環境溫度Ambient temperature：25℃濕度humidity：RH60%）
項 目
Item
符號
Symbol
數值
Value
單位
Unit
備註
Remark
正向電流
Forward Current
IF
20
mA
---
正向峰值電流
Peck forward current
Approved by
市場部
Market Dept.
客戶確認
CUSTOMER CONFIRMATION
確認
Confirmed by
審核
Checked by
核准
Approved by
型號Model：
一、外形圖Outline dimensions：
單位
Unit
公差
Tolerance
晶片材料
Die material
IF=20mA
--
120
--
deg
備註：亮度測試公差±15%、波長測試公差±1nm、正向電壓測試公差±0.05VRemark：The tolerance of intensity:±15%, The tolerance of wave length:±1nm,The tolerance of forwards voltage: ±0.05V. Only reference for above data when testing.
型號Model：
二、光電參數Photoelectricity Parameter（環境溫度Ambient temperature：25℃濕度humidity：RH60%）
項目
Item
符號Symbol
測條件Testcondition
最小值
Min
典型值
Type
最大值
Max
單位
Unit
正向電壓Forward voltage
膠體顏色
Lens color
發光顏色
Emission color
mm
±0.2mm
--
--
※備註：承認書之編號和型號可用于查詢，客戶如有需要，請提供相應的編號和型號。
Remark：P/N & Model in samples approval sheet can be used to inquire，please provide corresponding P/N& model if customer need .
描述
Description
項目
Item
測試標準
Test criterion
測試條件
Test condition
測試時間
Test time
數量
Qty
失效數量
Fail qty
壽命測試
Life test
常溫壽命測試
Life test(room temperature)
JIS7021:B4
Ta=25℃±5℃，IF=30mA