电梯术语-中英文对照

电梯专业术语中英文

abbreviation 缩语abnormal "不正常的,反常的"abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统 acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统 addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动 adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值 aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土 alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值 alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承 angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会 anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置 anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备 automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门 automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制 beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管 bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁 blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙 bottom counterweight overtravel 轿底对重越程 bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置 broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统 building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯 call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站 car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮 car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置 car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门 center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑"center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机 chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性"characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价 cinder concrete 煤渣混凝土circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度 cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制 collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同"compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容 condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台"construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置 control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置 cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机。

电梯常用术语（中英文）

电梯常用术语（中英文）1、1电梯 LIFT；ELEVATOR服务于规定楼层的固定式升降设备。

它具有一个轿厢，运行在至少两列垂直的或倾斜角小于15度的刚性轨之间。

轿厢尺寸与结构型式便于乘客出入或装货物。

2．1．1 乘客电梯PASSENGER LIFT为运送乘客而设计的电梯。

2．1．2 载货电梯GOODS LIFT；FREIGHTLIFT通常有人伴随，主要为运送货物而设计的电梯。

2．1．3 客货电梯PASSENGER-GOODS LIFT以运送乘客为主，但也可运送货物的电梯。

2．1．4 病床电梯；医用电梯 BED LIFT为运送病床（包括病人）及医疗设备而设计的电梯。

2．1．5 住宅电梯 RESIDENTIAL LIFT供住宅楼使用的电梯。

2．1．6 杂物电梯 DUMBWAITER LIFT； SERVICE LIFT服务于规定楼层的固定式升降设备。

它具有一具轿车厢，就其尺雨和结构型式而言，轿厢内不允许进入。

轿厢运行在两列垂直的或倾角15度的刚性导轨之间。

为满足不得进入的条件，轿厢尺寸不得超过：A）底板面积：1、00M*MB）深度：1、00MC）高度：1、20M但是，如果轿车厢由几个永久的间隔组成，而每一个间隔都能满足上述要求，高度超过1、20M是允许的。

2．1．7 船用电梯 LIFT ON SHIPS船舶上使用的电梯。

2．1．8 观光电梯PANORAMIC LIFT；OBSERTION LIFT井道和轿厢壁至少有同一侧透明，乘客可观看轿车厢外景物的电梯。

2．1．9 汽车电梯 MOTOR VEHICLE LLIFT；AUTOMBILE LIFT用作运送车辆而设计的电梯。

2．2 液压电梯 HYRAULIC LIFT依靠液压驱动的电梯。

3 一般术语3．1 平层准确度过 LEVELING ACCURACY轿厢到站停靠后，轿厢地坎上平面与层门地坎上平面之间垂直方向的偏差值。

3．2 电梯额定速度 RATED SPEED OF LIFT电梯设计所规定的轿车厢速度。

电梯专业术语中英文

abbreviation 缩语abnormal "不正常的,反常的"abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统 acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统 addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动 adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值 aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土 alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值 alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承 angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会 anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置 anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备 automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门 automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制 beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管 bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁 blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙 bottom counterweight overtravel 轿底对重越程 bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置 broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统 building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯 call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站 car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮 car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置 car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门 center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑"center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机 chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性"characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价 cinder concrete 煤渣混凝土circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度 cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制 collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同"compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容 condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台"construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置 control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置 cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机。

电梯术语中英文对照表

电梯术语中英文对照表ID Chinese English Remarks1交流控制ac control利用交流电动机驱动提升机器以实现拖动控制的形式.2自动越层automatic by-pass电梯监控系统的一个特征,它使电梯轿厢在某种情况下自动越过候梯厅的呼叫.3自动控制automatic control用以确定任一控制误差,功率放大,负反馈的闭环控制系统.4自动按钮控制automatic pushbutton control一个用以说明单台轿厢最简单自动控制方法的术语.5平衡的交通balanced traffic用作中间层楼交通情况的术语,指明上方向和下方向的交通流量实质上是相等的.6大楼人口数量building population大楼内的全部人员数.7越过楼层by-pass floors在大楼中被电梯超越不停的搂层,原因是由于监控或电梯满载而造成.8接受呼梯call accepted电梯控制系统接收停站或轿厢的呼梯信号.9呼梯分派call allocation电梯监控系统分派停站呼叫的动作.10召唤维修call back服务性查询,在电梯司机(或操作者)的要求下,由一名电梯维修技师完成的服务,原因是电梯发生故障而停止服11轿厢分派car allocation电梯监控系统分派停站呼叫的动作.12呼梯/内呼car call轿厢内的乘客要求电梯在某特定楼层停站.14轿厢调度car dispatch用于电梯监控系统的一个种类,轿厢在大楼的端站按照计划的间隔,派往指定的楼层.15手柄开关操纵car handle control电梯司机转动手柄位置(开断/闭合)来操纵电梯运行或停止.16轿内开关控制car switch operation电梯司机转动手柄位置(开断/闭合)来操纵电梯运行或停止.17集选控制collective selective control在信号控制的基础上把呼梯信号集合起来进行有选择的应答.18商业大楼commercial building19直流控制D.C control利用直流电动机驱动提升机器以实现拖动控制的形式.20方向箭头direction arrow带亮光的箭头符号指示运行方向.21调度间隔时间dispatch interval time由调度监控系统控制的一组电梯,轿厢连续离开一个终端层站之间的时间间隔.22调度讯号dispatch signal传递给电梯动力控制系统的讯号,使电梯轿厢运行.23门关闭着的时间door closed time电梯门保持关闭状态的时间周期.24门关闭所有时间door closing time电梯门保持关闭状态的时间周期.25门停顿时间door dwell time电梯门开启完成后,电梯门在层站保持开启状态的时间.(同:door holding time)26门保持时间door holding time电梯门开启完成后,电梯门在层站保持开启状态的时间.(同:door dwell time)27门区door zone从层站楼面上下方向测定的一个距离(约30厘米),当轿厢在该楼层平层运行时,容许轿厢门开启.28下行箭头down arrow带亮光的箭头符号或安装在电梯轿厢内的后壁上,或沿轿厢入口上方安装,以指示乘客轿厢运行的方向.29下行呼叫down call乘客要求存储停站讯号,要求电梯向下方向行驶.30下集选控制down-collective automatic operation集合电梯运行下方向的呼梯信号,如果乘客欲从较低的层站到较高的层站去,须乘电梯到底层基站后再乘电梯31下集选控制down-collective control 集合电梯运行下方向的呼梯信号,如果乘客欲从较低的层站到较高的层站去,须乘电梯到底层基站后再乘电梯32下行高峰乘客到站率down-peak passenger arrival-rate33驱动控制drive control控制电梯启动,停止,运行方向,加速,减速及电梯轿厢运行速度的系统.34并联/群控duplex/triplex control共用一套呼梯信号系统,把两台或三台规格相同的电梯并联起来控制.35全集选控制full collective control36群梯集合控制group automatic operation将几台电梯控制连在一起,分区域进行综合统一控制,对乘客需要电梯情况进行自动分析后,选派最适宜的电梯37梯群控制group collective control将几台电梯控制连在一起,分区域进行综合统一控制,对乘客需要电梯情况进行自动分析后,选派最适宜的电梯38群控group control for lifts将几台电梯控制连在一起,分区域进行综合统一控制,对乘客需要电梯情况进行自动分析后,选派最适宜的电梯39群梯监控group supervisory control一种能监控互联梯群的控制系统.40外呼/厅门呼叫hall call乘客在楼层用呼叫按钮输入去大楼内另一楼层的呼叫讯号.(同:landing call)42厅门呼叫停车hall stop乘客在楼层用呼叫按钮输入去大楼内另一楼层的呼叫讯号.(同:landing call)43事业型大楼institutional building44密集客流交通intensive traffic当要求一部电梯每小时起动超过180次时,则为重载交通.45中间楼层乘客到站率interfloor passenger arrival-rate当任一五分钟内,为服务而到达电梯系统的乘客数.46外呼/厅门呼叫landing call乘客在楼层用呼叫按钮输入去大楼内另一楼层的呼叫讯号.(同:hall call)48最低呼梯返回low(est) call reversal在电梯转换运行方向之前的下行方向上,电梯抵达的最低层站的呼叫.49最低返回楼层lowest reversal floor当轿厢向下运行完成其最后的一个轿内指令后,准备应答已登记的上行呼梯信号,特别是在楼层间客流的情况50按钮控制pushbutton control电梯运行由轿厢内操纵盘上的选层按钮或层站呼梯按钮来操纵.(同:pushbutton control)51按钮控制pushbutton operation电梯运行由轿厢内操纵盘上的选层按钮或层站呼梯按钮来操纵.(同:pushbutton control) 52住宅楼residential building53自动再平层self re-leveling当电梯轿厢停平在楼层水平后,在轿厢上下乘客的过程中使轿厢相继移动,则该操作可校正停层的位置.54信号控制signal operation55上行箭头up arrow带亮光的箭头符号或安装在电梯轿厢内的后壁上,或沿轿厢入口上方安装,以指示乘客轿厢运行的方向.56上行呼叫up call乘客呼梯,要求向上方向的停站.57上行高峰乘客到站率up-peak passenger arrival-rate当一个五分钟高峰内,为服务而到达电梯系统的乘客数.58重载交通intensive duty traffic当要求一部电梯每小时起动超过180次时,则为重载交通.原因是电梯发生故障而停止服务.许轿厢门开启.示乘客轿厢运行的方向.乘电梯到底层基站后再乘电梯到要去的高层站.乘电梯到底层基站后再乘电梯到要去的高层站.自动分析后,选派最适宜的电梯及时应答呼梯信号.(同:group collective control)自动分析后,选派最适宜的电梯及时应答呼梯信号.(同:group automatic operation)自动分析后,选派最适宜的电梯及时应答呼梯信号.(同:group automatic operation) ,特别是在楼层间客流的情况时,轿厢反方向的楼层.操作可校正停层的位置.示乘客轿厢运行的方向.。

电梯术语中英文对照表

Page 2
110 电梯司机 111 轻载服务 112 轻载交通 113 乘载间隔时间 114 本楼层区 115 最低返回楼层 116 机房 117 机房面积 118 机房深度 119 机房高度 120 机房宽度 121 主楼层 122 基站 123 主端站楼层 124 中载交通 125 远距监测 126 多梯井道 127 乘客人数 128 呼叫控制 129 一比一缠绕 130 电梯司机 131 一般绳股 132 停靠 133 停靠楼层 134 停靠区 135 载荷百分数 136 性能指标 137 周期性试验 138 底坑 139 底坑深度 140 底坑高度 141 预定基站 142 滑轮间 143 额定载重量 144 额定载重量 145 额定速度 146 右向绳股 147 绳锁绳股 148 往返全程时间 149 越程 150 运行间隙 151 安全测试 152 计划控制 153 区域 154 井道 155 井道深度 156 井道电气 157 井道高度 158 井道照明 159 井道公差 160 井道宽度 161 轿厢立柱 162 井道内牛腿 163 单梯井道 164 单绕 165 隔层停靠操作
carrying capacity
48 轿顶检修站
car-top inspection station
49 中心线
central line
50 轿厢入口净尺寸
clear entrance to the car
51 普通区域
common sector
52 普通井道common源自well53 合同栽荷contract capacity
8 载货电梯
goods lift
9 液压电梯
hydraulic lift
10 电梯

电梯术语中英文对照表

call accepted indicator calling board
临近或包含在层站呼梯或轿厢指令按钮内的指示器，电梯监控系统已经接受并储存呼叫时，该指示器即点亮。设置在层站门一侧，召唤轿厢停靠在呼梯层站的装置。（同：call
button)
Page 2
34 呼梯按钮
36 凸轮 38 轿厢缓冲器 39 轿厢按钮 40 轿厢顶板 41 轿厢装饰顶
emergency opening) 在轿厢顶部向外开启的封闭窗,供安装,检修人员使用或发生事故时援救和撤离乘客的轿厢应急出口.窗上装有当窗扇打开即可断开控制电路的开关. 由金属板与轿厢底,轿厢顶和轿厢门围成的一个封闭空间.(同:car
enclosures)
50 轿厢壁 51 轿厢出入口 52 轿厢风扇 53 轿厢地板 54 轿厢架/轿架 56 轿厢扶手 57 轿厢隔音 58 轿厢控制面板 59 轿厢底/轿底
常以橡胶或铁板制成的半圆形装饰线条，装在厅门和轿厢门的前缘并延伸到中分门的整个高度，或垂直中分门的整个宽度，以减小当门碰到乘客时的伤人作用并使门操作平稳。装在载货电梯垂直中分门上扇门低部的一个弹性，且不可压缩的安全触板。
Page 1
19 自动关闭器 20 锁杆
21 垂直中分门 22 制动器
置于轿厢门上的装置，其功能是保证轿门在使用后能自动关闭，其原理是使用存储在一套重块或弹簧上的能量。（同：automatic
closer) 除非厅门都关闭,否则该装置将防止驱动机器运转. 机械锁,用来当轿厢不在门区时,防止轿厢或层门开启. 同一井道内有多台电梯,在相邻轿壁上并向开启的门,供乘客和司机在特殊情况下离开轿厢,而改乘相邻轿厢的安全出入口.(同:car

电梯专业术语中英文

abbreviation 缩语abnormal "不正常的,反常的"abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统 acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统 addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动 adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值 aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土 alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值 alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承 angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会 anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置 anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备 automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门 automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制 beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管 bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁 blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙 bottom counterweight overtravel 轿底对重越程 bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置 broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统 building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯 call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站 car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮 car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置 car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门 center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑"center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机 chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性"characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价 cinder concrete 煤渣混凝土circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度 cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制 collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同"compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容 condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台"construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置 control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置 cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机。

电梯术语中英文对照表.pdf

电梯术语中英文对照表.pdfID Chinese English Remarks1检修门/通道门access door 开设在井道壁上，通向底坑或滑轮间供检修人员使用的门。

3航空细索air cord 由一小直径钢丝绳制成的电梯门机驱动机构零件。

4警铃alarm bell 置于电梯井道内，或适宜的楼层，或轿厢上，当乘客按轿厢内按钮以操纵该铃时，用以呼唤以引起人们的注意和援助。

5警铃按钮alarm bottom 设置在轿厢面板上操纵警铃的按钮。

6报警系统alarm system 安装在轿厢上的应急系统，它包括一个铃，一个装在轿厢内的按钮和一个不间断电池电源。

7卸扣anchorage8角架支架angle bracket 用以牢固地将导轨连接井道建筑构件上的型钢制的机械部件。

10防捣乱装置anti-nuisance device 防止有乘客捣乱或故意输入较乘客人数多的轿厢指令讯号；或无乘客时将电梯开走的装置。

11补偿绳防跳装置anti-rebound of compensation rope device 当补偿绳张紧装置超出限定位置时，能使曳引机停止运转的电气安全装置。

12框线architrave 围绕门口的各部分，以维护整洁的外观；装饰线条。

14到达铃/到站钟头arrival bell 置于电梯轿厢上或作为装饰件於层楼处，以示明电梯轿厢到达接送乘客的楼层。

17饰条astragal 常以橡胶或铁板制成的半圆形装饰线条，装在厅门和轿厢门的前缘并延伸到中分门的整个高度，或垂直中分门的整个宽度，以减小当门碰到乘客时的伤人作用并使门操作平稳。

18安全饰条safety astragal 装在载货电梯垂直中分门上扇门低部的一个弹性，且不可压缩的安全触板。

19自动关闭器automatic closer 置于轿厢门上的装置，其功能是保证轿门在使用后能自动关闭，其原理是使用存储在一套重块或弹簧上的能量。

（同：car door closer)20锁杆bar lock 用于人力操作门的一种门联锁形式。