过滤机中文样本
净水器中文说明书【范本模板】
反渗透水质处理器主要功能家用反渗透水质处理器，协调完成纯水制造的自动化过程。
在安装好的情况下,打开水源,低压开关自动闭合，反渗透水质处理器开始制水。
当储水桶的水满时，高压开关断开.饮用纯净水同时,储水桶内的压力会逐渐下降，反渗透水质处理器又开始制水。
当水源断水时，低压开关自动断开，反渗透水质处理器处于停机状态；反之，低压开关闭合开始制水.让您随时都可以喝到甘甜可口的纯净水。
新安装的反渗透水质处理器，应防掉一至二桶的纯水冲洗新机后，方可开始饮用.特别注意1.本机必须由专业人员安装，在使用前详细阅读说明书，以免对您正常饮水造成不必要的麻烦.2.用户若数天不用(外出），应关闭本机电源及水源。
3.以包装箱内实际配置为准4.安装完毕请检查螺帽是否紧固以免漏水,无地漏或者地漏不完善之场所严禁安装本公司产品，否则造成财产损失，本公司概不负责。
安装及使用注意事项为了防止危害使用者安全，损害他人财物事件的发生，请务必严守一下说明1.安装服务人员在安装前应先检查系统电路部分是否正常，因为在运输装卸过程中有可能引起接线松动,组件损坏.2.如果您要自选安装，请严守安装说明。
3.请勿随意更改电路和管路。
4.请勿自行调节高、低压开关等控制组件,如因自行调节造成损失，本公司概不负责。
5.出现故障请与当地经销商联系，请勿随意更改。
*不可在高于220V的电压下长时间运作*＊去除率=［（原水T。
D。
S值—纯水T。
D.S值)＊100％]/原水T。
D。
S值＊＊*低于0.1Mpa需加装增压泵,高于0。
35Mpa需加装减压泵。
六级过滤，从粗到细,层层把关，确保水质第一级:pp5μm纤维滤芯，去除水中大于5μm的悬浮物，如沙石、铁锈、铜锈、磷污等第二级：颗粒活性炭滤芯，吸附书中的异色异味、氯及氯的副产物等第三级：烧结活性炭滤芯，可去除水中氯、有机化学物、异色、异味以及污泥悬浮物颗粒等第四级：最关键最核心部件采用反渗透RO膜。
彻底除去水中细菌、病毒、重金属、有机物等杂质。
各种过滤器样本(南通飞特尔)
YQXP II 型过滤器
YQXC I 型复合式在线手动清洗过滤器
注意事项 YQX 型在线式手动清洗过滤器可水平或垂直安装，安装时应注意外壳上箭头方向必须与水流方向一致。
订货须知 （1）、本公司生产的 ZJS 系列过滤器，公称压力等级为 0.6、1.0、1.6、2.5、4.0、6.3MPa，采用化工部 HG20592 标准，用户
过滤器是工业生产中不可缺少的管道设备，安装在管道上能除去流体中的固体杂质，使机器设备（包括压缩机、泵等），仪表 正常工作和运转，达到稳定工艺过程，保障安全生产的作用。另外对提高产品质量也有十分重要的意义。
本公司生产的普通过滤器具有结构紧凑、过滤能力大、压损小，适用范围广、维护方便、价格低廉等优点。 公司新近推出的智能过滤器系列产品，除具有普通过滤器的所有功能外，同时还具有提供更换、清洗滤网信息的樗和远程声光 报警功能，它的基本原理是利用流经过滤器流体入口与出口的压力差，使智能器内压差式信息发生动作，在智能器一端的红圆柱便 冒出或发生报警信息，表示滤网被阻塞需要更换或清洗。它克服了当今普通过滤器因无法及时指示滤网的阻塞程度而造成断流、烧 泵或误判滤网阻塞白白浪费入力、物力等弊端，是一种理想的更新换代产品。若将它串联地安装在泵的入口或系统管线的其它部位， 既可处长泵和其它设备的使用寿命，又能保证整个系统安全。
规格型号与技术参数
正向流锥形式临时过滤器
反向流锥形式临时过滤器
在线式手动清洗过滤器 产品简介
YQX 系列在线式手动清洗过滤器适用于各种供水系统、工艺管路及工业循环水系统，特别是 24 小时连续运行的不停机系统， 确保系 统的安全可靠运行，是一种简洁高效的过滤器，广泛应用于石油、化工、冶金、环保、采矿、制药、食品、造纸等领域。
H 400 450 500 550 600 650 750 1020 1240 1310
Pall 9020过滤器样本
9020/21/24 Series Filter AssembliesFeaturing Coreless Element TechnologyFlows to 20 gpm (75 L/min)Pressures to 3000 psi (207 bar)Port size: 3/4"SpecificationsFeaturesFull Flow Fast Response Bypass ValveForged Aluminum Alloy Bowl (Anodized)Optional Differential Pressure DevicesExtruded Aluminum Alloy Head (Anodized)O-Ring SealsUltipor® III ElementMaximum Acceptable Working Pressure: 3000 psi (207 bar)Fatigue Pressure Rating:(NFPA/T2.6 1 -1974 category 2/90)R length-1800 psi (124 bar)S length-1500 psi (103 bar)Typical Burst Pressure:15,000 psi (1035 bar)Temperature Range:Nitrile seals-45°F to 225°F (-43°C to 107°C)Fluorocarbon seals-20°F to 250°F (-27°C to 121°C)140°F (60°C) maximum in HWCF or water-glycol fluidsDry Weights:R length-3.7 lbs. (1.7 kg)S length-5 lbs. (2.3 kg)Filter Element Collapse Pressure:9020-290 psid (20 bar)9021-3000 psid (207 bar)9024-150 psid (10 bar)Dimensional DrawingsPerformancePressure Drop InformationElement Pressure Drop FactorMultiply actual flow rate times factor to determine pressure drop with fluid at 150 SUS (32 cSt), 0.9 S.G.Correct for other viscosities by multiplying new viscosity in SUS/150 x new S.G/0.9.9020 Series Element P factor (psid/gpm)Length KZ KP KN KS KT4" 1.90 0.82 0.54 0.35 0.218" 0.96 0.41 0.27 0.18 0.119021 Series Element P factor (psid/gpm)Length DP DT4" 2.71 0.688" 1.35 0.349024 Series Element P factor (psid/gpm)Length KZ KP KN KS KT8" 1.12 0.48 0.31 0.21 0.13Ordering InformationAssembly P/N: H 902Table1 Table2 Table3 Table4 Table5 Table6 Table7 Table8Element P/N: HC 902 FTable2 Table5 Table6 Table1Note: Choose from the options in the following tables to compile the specific Product Number.Table 1: Seal OptionsCode SealsH NitrileZ FluorocarbonTable 2: Element OptionsCode Rating0290 psid (standard)13000 psid (high collapse)4150 psid (coreless)Table 3: Port Style OptionsCode Port StyleA SAE J514 straight threadL Manifold side mount*K Manifold mount*Contact factory for drawings.Table 4: Port Size OptionsCode Size12 3/4"TABLE 5: FILTER ELEMENT OPTIONSCODE ßx 200ßx(c)=1000 KZ <1 2.5KP 3 5KN 6 7KS 12 12KT 25 22DP* 3 5DT* 17 15*9021 series only.Table 6: Length Options*Assembly Code Element Code** R***4S8*Use code in second column for element part no.**Nominal length in inches***Not available for 9024 seriesTable 7: Bypass Valve OptionsCode DescriptionB50 psid-9020/9024 onlyW Non bypass 9021 onlyTable 8: Differential Pressure Device OptionsCode DescriptionP Visual indicator with thermal lockoutD Visual indicator with no thermal lockoutL Electrical switch (SPDT) with 6" leadsT Electrical switch with DIN connectorM'T' type switch with matching wiring capS Electrical switch with MS receptacleV Combined visual/electrical with DIN connectorB Plug in place of indicatorContact InformationFOR TECHNICAL ASSISTANCE CALL TOLL FREE 1-888-333-PALL (7255)© Copyright Pall CorporationVisit us on the Web at 。
纸板式过滤机说明书
产品使用说明书GL型板框式过滤机使用说明书目录一、概述 (2)二、规格与性能参数 (3)三、结构与工作原理 (4)四、安装与调整的注意事项 (5)五、操作与使用说明 (6)六、维护与保养 (10)七、随机附件 (10)一、概述不锈钢板框式过滤机是一种高级滤清、除菌设备，装配以不同型号的过滤介质可对酿酒、制药、饮料、化工等许多行业的液态制品进行精度不同的澄清过滤和除菌过滤。
本过滤器体积小，效率高，操作简便，应用范围广。
触液零件全部用1G18Ni9Ti不锈钢制造，耐磨蚀性能优越，使用寿命长。
根据不同的使用要求，该机配有塑料板框，价格低廉。
外形图：主视图右视图二、规格与性能参数规格：型号过滤板数有效过滤面积（m2）GL20 8~26 0.24~0.78GL30 19~29 1.4~2.1GL40~ 40 21~41 2.95~5.75 70 43~71 6.05~9.98 100 73~101 10.27~14.2GL60~ 100 70 23.31 150 120 39.96 200 170 56.61 250 220 73.26性能参数：型号过滤板数最大过滤量（升/片*小时）推荐工作压差（巴）澄清除菌澄清除菌GL20 8~26 20~40 10~20 3 1.5GL30 19~29 50~100 25~50 3 1.5GL40 21~101 100~200 50~100 3 1.5GL60 70~220 200~400 100~200 3 1.5（本机最高工作压力为4巴）三、结构与工作原理本过滤器是由前支架和尾架用两根主轴相连结成为一个水平放置的框架，在前支架和尾架中间有一个可以与前者平行移动的堵头，堵头的移动由安装在尾架上的丝杠拖动。
因此在前支架与堵头中间形成两个间距可调的平行平面，这两个平面就可以借助于丝杠压紧装在中间的过滤片组，整个机构类似于一个卧式双柱螺旋压力机构。
中间过滤片的两侧有通液甲（连通）和通液乙（不连通）各两个，当压紧时这些通液环由胶圈密封而形成四条通液管路。
黎明液压 SGF系列双筒高压过滤器样本
m and the filter equipped with indica-
( )
MOUNTING SIZE
H1 D A L L1 L4 H
2-DN
6-M
2-d1 B2 B1 P2 B4 B3
B6
L2
B7
L3
B5
B3
4-d
P1
B
Unit:mm H SGF-H30 * SGF-H60 * SGF-H110 * SGF-H160 * SGF-H240 * SGF-H330 * SGF-H500 * SGF-H660 * 180 196 265 251 309 330 423 497 H1 106 106 106 129 129 152 152 152 B 242 242 242 278 278 377 377 377 B1 136 136 136 172 172 230 230 230 B2 106 106 106 142 142 190 190 190 B3 32 32 32 45 45 57 57 57 B4 36 36 36 48 48 66ቤተ መጻሕፍቲ ባይዱ66 66 B5 28 28 28 29 29 41 41 41 B6 30 30 30 30 30 48 48 48 B7 15 15 15 15 15 20 20 20 A 120 120 120 140 140 210 210 210 L 246 246 246 296 296 414 414 414 L1 210 210 210 260 260 380 380 380 L2 104 104 104 110 110 160 160 160 L3 46 46 46 52 52 85 85 85 L4 134 134 134 140 140 200 200 200 D 73 73 73 102 102 146 146 146 DN 20 20 20 32 32 50 50 50 1 d 28 28 28 40 40 60 60 60 d 17.5 17.5 17.5 17.5 17.5 26 26 26 M M12 M12 M12 M12 M12 M20 M20 M20
派克TTF系列过滤器中文样本
TTF最大：500 L/min, 10 bar特点&好处典型应用• 垃圾车• 移动式起重机• 动力站• 轮式装载机• 钻井设备TTF 系列回油管路过滤器TTF 油箱顶置回油管路过滤器内设有磁铁和低阻滞的全流量旁通阀，具有预过滤功能。
由于采用了由里向外的过滤原理，受污染的油液因此不可能倒流回系统。
TTF 系列过滤器可处理的流量最大可达500l/min ，最大压力可达10bar ，用户可选过滤器端盖上的注油口，第二个回油口和用户自定义的扩散器。
也可提供集成式的(TSR 系列)带有4个回油口的过滤器滤头。
TTFTSR1345678101112131415169a9b类型 1-125/2-170/2-230/2-3002-400/2-500类型1-60/1-90/1-120滤芯安装间隙F8136最低油位安装孔B 137LHØ50Ø102±1Ø410.33.2BAAØ1656481814x ISO228G 1/8”(BSP)4x Ø1112工作压力:最大. 10 bar .安装方式:油箱顶置安装.接口:螺纹 BSP 接口.法兰接口可按要求提供集成式滤头TSR 可按要求提供流量可达 250 l/min.过滤器外壳:铝质滤头和端盖.密封材料:丁腈橡胶, 氟橡胶, 氯丁橡胶.工作温度范围:-40 - +120°C.旁通阀设定:开启压力 0.8 / 1.5 或 2 bar .其它要求请咨询过滤效果:决定于多次通过实验符合ISO 16889.液流疲劳特性:过滤材质可确保获得最佳的疲劳寿命过滤材质:Microglass III & Ecoglass III LEIF ®滤芯.也可提供10μm 纸质纤维和40μm 不锈钢金属网滤芯的爆破压力:10 bar (ISO 2941)压力指示器选项:设定值 0.7 或 1.2 bar .其他的设定值请咨询.目视压力表.电讯式压力继电器.选项:扩散器列类型 P (直管,无开孔板区域)扩散器 T (带有封闭的扩散器端帽和开孔板区域，当进入油箱的油液接近油箱底部或为了确保进入的油液处于油箱液位之下时推荐使用)磁铁组件:标准的 TTF400 和 500 作为标准供货不包括磁铁端盖上注油口(可选)堵塞.过滤器滤芯:LEIF ®滤芯带有可多次使用的金属滤芯护套 可选传统的带有碳钢端帽的滤芯.LEIF ®滤芯专利产品可保证使用真正原装产品。
空气过滤器 FFU中英文资料
95/30 1990/80
825/30 1650/80
660/20 1700/20 850/20 1420/20 1180/20 950/20 1800/18 850/18 1420/18 1180/18 950/18
1325/63 3400/70 1700/70 2840/70 2360/70 1870/70 3400/68 1700/68 2840/68 2360/68 1870/68
htpp://
Dirkbiel
3
Integrity、 Quality 、Innovation 、Service、Value (IQIS＆V)
MF-Air FilterG3,G4 金属框空气过滤器
The initial effect panel type filter is suitable for the initial filtration of air conditioner and ventilation systems, filtration of the returned air in the clean chambers and pre-filtration for the partial high-effect filtration systems. It has been broadly used in various industries, to include electronics, electric appliances, aviation and aerospace, automobiles, pharmaceuticals, biological engineering, environmental protection, telecommunication, banks, intelligent buildings, hotels, restaurants, etc.
丹佛斯干燥过滤器DML-DCL样本
All ELIMINATOR® driers have a solid core with binding material held to an absolute minimum. There are two types of ELIMINATOR® cores.Type DML driers have a core composition of 100% Molecular Sieve, while type DCL contain 80% Molecular Sieve with 20% activated alumina. ELIMINATOR® type DML driers are designed for applications requiring the highest moisture capacity.ELIMINATOR® type DCL driers are designed for applications requiring high moisture capacity and acid adsorption capacity.Available with solder (pure copper) and flare connections.Features The Core type DML• 100% 3Å Molecular Sieve core• High drying capacity minimizing the risk of acidformation (hydrolysis)• Recommended for use with HFO, HC, HFC andHCFC refrigerants• Will not deplete oil additivesThe Core type DCL• 80% 3Å Molecular Sieve with 20% activatedalumina• Perfect core blend for systems that operate athigh condensing temperatures and require highdrying capacity• Recommended for use with HFO, HC, HFC andHCFC refrigerants The Shell• UL approved for MWP 667 psig• Available with solder (pure copper) and flare connections• Corrosion resistant powder-painted finish. Special coating for marine applications available upon request• Allows installation with any orientation provided the arrow is in the flow direction• Available in sizes 3 – 75 cubic inchesThe Filter• 25 μm (0.001 in.) filter provides high retention with minimal pressure drop• Thermally stable up to 250 °FApprovals UL US, file no. SA 6398PED 97/23/EC - a3p3Compliant with ATEX hazard zone 2Note: Only solder versions (cu-plated / pure copper) andconnection sizes below 25 mm are approved for flammablerefrigerants now.Application Technical data ELIMINATOR® hermetic filter driers protectrefrigeration and air-conditioning systems fromWith these contaminants eliminated, systems aresafer from harmful chemical reactions and fromTCAESGN GBC DML / DCL GBC Flare connectionFilter drier volume(shell volume)(Total Acid Number)Technical data and capacities–R32: 990 ppm W - 50 ppm W–R134a: 1050 ppm W – 50 ppm W–R404A, R507: 1020 ppm W – 50 ppm W–R407C: 1020 ppm W – 50 ppm W–R410A: 1050 ppm W – 50 ppm W–R22: 1050 ppm W – 60 ppm Win accordance with ARI 710-20042) Given in accordance with ARI 710-2004 for–t e= 5 °F–t c= 85 °F–Δp = 1 psiFor technical data on other refrigerants, please contact your Danfoss Sales RepresentativeTechnical data and capacities(continued)–R32: 990 ppm W - 50 ppm W –R134a: 1050 ppm W – 50 ppm W–R404A, R507: 1020 ppm W – 50 ppm W –R407C: 1020 ppm W – 50 ppm W –R410A: 1050 ppm W – 50 ppm W –R22: 1050 ppm W – 60 ppm W in accordance with ARI 710-20042) Given in accordance with ARI 710-2004 for –t e = 5 °F –t c = 85 °F –Δp = 1 psiFor technical data on other refrigerants, please contact your Danfoss Sales RepresentativeConversionsSee ARI standard 710-2004 for recommended initial and final PPM values for different refrigerantsDrops of water =(lbs of refrigerant × (Initial PPM of water - Final PPM of water))110OrderingD a n f o s s 23Z 8403Ordering(continued)D a n f o s s 23Z 8404Ordering (continued)D a n f o s s 23Z 8403Ordering(continued)D a n f o s s 23Z 8404IdentificationExample for type codesDML 1.52x2/2s F i l t e r d r i e rS o l i d c o r eA p p l i c a t i o nS i z e (v o l u m e )C o n n e c t i o n (fi l t e r c o n n e c t i o n i n 1⁄8 o f a n i n c h i n c r e m e n t s )C o n n e c t i o n t y peF i l t e r d r i e rS o l i d c o r eA p p l i c a t i o nS i z e (v o l u m e )C o n n e c t i o n (fi l t e r c o n n e c t i o n i n 1⁄8 o f a n i n c h i n c r e m e n t s )D u a l c o n n e c t o r i n l e t / C o n n e c t i o n o u t l e t i n 1⁄8 o f a n i n . i n c r e m e n t sC o n n e c t i o n t y peSelection2) DCL Hermetic filter driers contain activated alumina, which is a polar material used for acid adsorption. Many oil additives are alsopolar substances and can be adsorbed by the activated alumina, rendering them useless, and reducing the drier’s acid capacity,though this is not harmful to the system.Selection example Select the appropriate type (DML or DCL) basedon refrigerant and oil type. Then select the driersize based on the adsorption and liquid capacityrequired.a. Amount of charge: 55 lbs R134a at tL = 75 °FTo dry 55 lbs R134a at 75 °F from 1050 to 60 ppmmoisture, a DML 16 is necessaryb. Cooling capacity: Qe = 5.7 TRTo obtain a mass flow corresponding to 5.7 TRcooling capacity with a DML 16 filter drier,a 3⁄8 in. connection must be chosen.Larger connections can be chosen in accordancewith the liquid line dimension c. ResultDML 163 or DML 163s can be usedIf the initial moisture content is very small or a planned change of the filter drier is considered, a smaller filter drier size can be chosen.The relatively large diameter of the hermetic filter drier means that the liquid flow velocity is suitably low and the pressure drop minimal.Powder formation is eliminated because the solid core grains are bonded and cannot move against each other.Design / Function DML 1.5DML / DCL 03DML / DCL 08, DML / DCL 16DML / DCL 60, DML / DCL 75DCL 1.5DML / DCL 05DML / DCL 30, DML / DCL 411. I nlet2. S pring3. S olid core4. P olyester mat5. P erforated plate6. S eal cap, flare connection7. S eal cap, solder connectionDimensions and weights Flare connectionsDimensions and weights (continued)Flare connectionsDimensions and weights (continued)Solder connectionsDML 1.52sDCL 1.52XL/2.8mm sDCL 1.52x2/2sDimensions and weights (continued)Solder connectionsDimensions and weightsSolder connections(continued)。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
The New High Efficiency Hyperbaric Filtrationthrough PowerFilter TM新型高效PowerFilter TM加压过滤技术SEPARATION TECHNOLOGIESThe Andritz World Map安德里茨全球分布图You are making the right choice ……你正在做出正确的选择SEPARATION TECHNOLOGIES•4% of Group sales.•Plants, equipment, and services for the 9% of Group sales.Plants, equipment, and services for solid/liquid separation formunicipalities and industries (e. g. mining, chemical and petrochemical industries, food industry).17% of Group sales.30% of Group sales.Plants and services for 40% of Group sales.Electromechanical 水力发电制浆造纸金属环境与工艺食品与生物燃料SEPARATION TECHNOLOGIESAndritz Separation Technologiesfor Mining ApplicationMembrane and Chamber Filter PressesDecanter, Centrifuges Membrane and ChamberFilter PressesMembrane and Chamber Filter PlatesHyperbaric & Vacuum Filters and Belt PressesVibrating and Screen Bowl CentrifugesMembrane Filter Presses&Belt Presses箱式隔膜压滤机和带式压滤机Single or Combined Dewatering Systems can be SuppliedKind of “all safe”HYPERBARIC FILTRATION加压过滤TODAY‘S REQUIREMENTS当前的社会需求-Availability> 95% 设备利用率95%以上-24 h Operating 24小时连续运转-Emergency Spare parts紧急备件供应-Combination with other systems便于与其他系统的联合-Costs in RMB/ton DS/year become more important than investment 运行成本比初期投资更重要-Low moisture 产品水分低-Clear filtrate due to circulate and environmental aspects符合闭路循环和环保要求的清澈滤液-Ultrafines material treatment 极细物料处理-Engery savings节能SEPARATION TECHNOLOGIESHYPERBARIC FILTRATION 加压过滤Pressure Filters for highperformance filtration offines in ore and coalprep.plants as well asvarious industrialapplications加压过滤机用于金属矿、选煤厂及其他不同工业领域的细颗粒高效过滤脱水The Hyperbaric Filter has been found to be the most effective andproven dewatering technology for the increasing fine coal production.加压过滤机已经证明是处理细粒煤的最高效的脱水技术和设备SEPARATION TECHNOLOGIESSEPARATION TECHNOLOGIESHyperbaric 600-16000123456000-000Specific throughput [kg DS/m², h]V a c u u m F i l t e r O p e r a t i o n R a n g e Filter Range of OperationDifferential Pressure [bar]600-900750-12001500-2500900-1600300-600500-1500250-500180-500250-350Both the residual moisture and throughput increase significantly if the pressure difference is increased.工作压差的增加会使产品水分和处理量都能得到显著改善！！！HYPERBARIC FILTRATION 加压过滤Andritz HBF History安德里茨加压过滤机历史Andritz developed the first Hyperbaric Filter in the world安德里茨研制了世界第一台加压过滤机Andritz never stopped its study of application of HBF, that keeps Andritz always in advanced position in the world. On the similar productsmanufactured by other suppliers, we can always find the shadow of early form of Andritz HBF.安德里茨不断地进行加压过滤机的研发应用，在技术和性能方面一直保持领先的地位，从其它厂家的同类设备上我们都可以看到安德里茨早期加压过滤机的影子。
SEPARATION TECHNOLOGIESHYPERBARIC FILTRATION 加压过滤Andritz HBF History安德里茨加压过滤机历史•1986 First120 m2 HBF for coal filtration首台煤用加压过滤机•1991First HBF for Mineral 首台矿业用加压过滤机•1995First HBF in China 中国引进首台加压过滤机•1995 –2004 HBF in USA; Australia, Chile, Canada, Europe, China加压过滤机在美国、澳洲、智利、加拿大、欧洲和中国推广•2003First HBF in Russia 俄罗斯引进首台加压过滤机•2005Development of 168 m2 HBF 大型168 m2加压过滤机研制成功•20064Zone Filtration 四区过滤技术应用•2006Service Centre and Manufacturing in Foshan佛山工厂开始生产并组建服务中心•2007 Succesful start up of 5 lines HBF 168 m2五台168 m2大型加压过滤机调试成功•20088lines HBF 168 sold up to date 销售八台168 m2大型加压过滤机•2008First new120 m2sold, (delivery 2009) 首台新型120 m2加压过滤机SEPARATION TECHNOLOGIESHYPERBARIC FILTRATION加压过滤Andritz HBF Development安德里茨加压过滤机发展•Widely Applications of Coal, Copper, Lead, Zinc, Iron, Alumina, Bauxite, Red mud, Amylum and etc.应用涵盖了细煤泥、铜矿、铅矿、铁矿、锌矿、铝土矿、赤泥以及淀粉等的脱水•Special design and successful experience for ultra fine tailing coal dewatering 安德里茨近年来致力于研发尾煤的处理并取得了显著的成果，而且已经得到了成功的工业应用因此安德里茨加压过滤机在处理尾煤和泥化现象严重的煤泥方面具有独到的经验和实力。
•The new high efficiency product PowerFilter TM with more simple structure and more reliable running,结构更简单，运行更可靠的新型PowerFilter TM高效加压过滤机•The biggest PowerFilter TM in the world with168m2 filter area which will simplify the lay-out of whole plant and save investment cost.世界上最大的新型加压过滤机，它的过滤面积达168m2，，这样将可以进一步简化整个过滤车间的布置和投资。
SEPARATION TECHNOLOGIESHYPERBARIC FILTRATION加压过滤Convincing Technology for加压过滤技术优势•Continuous system -high throughput高处理量•Low residual moisture低残留水分•Reduction or virtual elimination of drying costs降低或完全省去干燥费用•Clear filtrate清澈的滤液•Low operation costs低运行成本•Fully automatic operation and easy plant monitoring全自动操作和方便的车间监控•Closed system封闭的系统SEPARATION TECHNOLOGIES1 -Pressure Vessel 加压仓2 –Manhole 人孔3 –Filterdisc 过滤盘4 -Control head 控制头5 -Filter drive 驱动单元6 -Filter trough 矿浆槽7 -Discharger 卸料闸门1234567SEPARATION TECHNOLOGIESHYPERBARIC FILTRATION 加压过滤成饼过程干燥过程吹饼过程HYPERBARIC FILTRATION加压过滤Filtration, Snap-blow& Discharging process 过滤、反吹和卸料过程Filtration 加压过滤过程Discharging自动卸料过程Snap-blow反吹卸料过程SEPARATION TECHNOLOGIES-Cycles of approximately 1 minute.循环周期约1分钟Controlled automatically by time switch or fillinglevel probe in the upper / cake receiving chamber.通过定时开关或者装在上仓的料位传感器自动控制卸料G. HaehlingNEW PowerFilter ™FILTRATION新型加压过滤•Up to 20% efficiency increase 效率可增加20%•Up to 5,8 bar for highest troughput and lowest moisture工作压力可高达5.8bar，有效保证最大处理量和最低产品水分•Up to 800 kg/m2/hr troughput产能高达0.8吨/平米/小时•Surface moisture10to 18% 产品外水可达10-18%•Availability more than8000 h/year每年运行时间可长达8000小时•With168 m220% reduction of specific investment costs采用168平米加压过滤机单位产量投资费用可减少20%•Reduction of infrastructural costs 减少基建投资•Systems combined with centrifuges can be offered可提供与离心机组成的联合工艺系统SEPARATION TECHNOLOGIESNEW PowerFilter ™FILTRATION新型加压过滤WhyAndritz HBFhas better quality and performance?为什么安德里茨加压过滤机有更高的质量和更优的性能？SEPARATION TECHNOLOGIESHYPERBARIC FILTRATION加压过滤New Development Technologies 最新技术应用1、New Patent High Throughput, High Reliability Powerfilter168新型大处理量、高可靠性的168m2高效加压过滤机专利技术2、New Control Head and Filtrate Pipes Design新型高效控制头和滤液管设计3、New Patent High Efficient Filterbag Cleaning System新型高效滤布清洗系统专利技术4、New Patent Slurry Paddle System新型矿浆搅拌专利技术5、New Patent Filter Cell Fixing System新型滤扇固定专利技术6、New Sealing System for Discharger新型卸料闸门密封系统SEPARATION TECHNOLOGIESNEW MODEL 168 m2 –Finite Elemente Optimised新型168m2矿浆槽体设计采用有限元分析优化-40% more throughputthan120 m2 but samemaintenance costs处理量增加40％，但维护成本相同-40% less specificmaintenance costs相当于维护成本降低40％SEPARATION TECHNOLOGIESSEPARATION TECHNOLOGIESHBF-Discharger –Type 3XL for more than 100 t/hthroughput -Designed for more than 100 t/hThroughput 设计通过能力超过100t/h-Special coat inside (on request)内部特殊涂层（选配）2layer ultra sliding material reduces wear of the wall and has excellent corrosion protection, resulting in increaded life time-New sealing system 新型密封装置(no screws inside 内部无螺栓)新型3XL 型卸料闸门通过量超过100t/hNew Discharger Sealing System ®新型卸料闸门密封装置Previous System 原设计Advanced System from OUTSIDE FIXED 新设计（从外部固定）-No srewing inside for changing sealing ring更换密封圈无需从内部拆装螺栓-80% faster than previous 比原设计更换速度提高80％-Fixed from outside 从外部固定-Long Life of sealing ring up to 12 months 密封圈使用寿命长达12个月SEPARATION TECHNOLOGIESQuick Fixing of Cells®滤扇快速固定设计-easy maintenance 方便维护-No screws!! 不需螺栓固定-production time 增加生产时间-safety 安全-no tools required 无需工具-all stainless steel parts 全不锈钢SEPARATION TECHNOLOGIESSEPARATION TECHNOLOGIES -No agitators outside-1 drive outside instead9 drives on top -Significant life time increase-reduced maintenance costs-increased productivity(aprx1 week/ year)-less energy consumptionIntegrated paddle agitator ®水平浆式搅拌装置New Design of Chain Conveyor配套新型刮板输送机-Bearings outside 轴承外部安装-Coupling outside 外部联轴器-Stainless trough 不锈钢槽体-New shaft & teeth design新型轮牙设计-Easy moving out 方便抽出更换Long life and Easy maintenance!!!寿命更长，更易维护！！！SEPARATION TECHNOLOGIESSEPARATION TECHNOLOGIESMultiple lights inside增强内部照明-Perfect maintenance and service -Safe operation -increasedlife timeSelf Filling Oil and Breath system 自动加油和透气装置Imported gear motors, bearings 进口高性能齿轮箱和轴承Control head in Coated Stainless steel(on request)不锈钢带涂层控制头（可选项）Options:-Stainless steel(on request)-Rubber coated inside(on request)Advantages:-Significant Increase in life time-Less service& maintenance SEPARATION TECHNOLOGIESSEPARATION TECHNOLOGIESControl disc material …Blue“®控制盘特殊材质Material …Blue“®UHDPP + special additives(Special design for wear applications)Advantage:-Multiple life time increase (for coal up to several years have been reported in long term tests )超强耐磨，实验证明煤炭应用使用寿命可长达数年！！！SEPARATION TECHNOLOGIESTrapeziform channels provide 20% more section area & throughput than normal round channels design.梯形流道设计比普通圆形流道设计多出20％的截面积，从而产生高出20％的处理量！Special channel design of control head and filtrate pipes 特殊的控制头和滤液管流道设计Andritz Special Design Local Normal DesignAndritz DesignSEPARATION TECHNOLOGIESAdvanced washing –access from outside for 120 m2改进型清洗装置—可从外部方便维护-Easy access to nozzles 方便清洗喷嘴-Saving of wash water energy due to new control philosophy根据新的控制逻辑节约清洗水消耗-No movement of washing nozzles requires less spare parts (no drive)清洗装置不运动，减少备件损耗（无需驱动）Power Filter™-Latest development 新研发成果4 Zone Filtration (cake formation, Array drying, snap blow, cleaning)4区域过滤（成饼、干燥、反吹、清洗)-Continuous cleaning duringoperation运行中滤布清洗-Gain:30 min production time/ day每天增加30分钟运行时间-apprx. 20% better productivity增加约20%产能-no agitators 无分体搅拌器Integrated cleaning综合清洗系统SEPARATION TECHNOLOGIESHBF-vessel – 4,8 m diameter for 168 m2 (standard) on request for 120m2 available 大直径加压仓和滤盘- Excellent space for maintenance and service 大空间更方便维护 - Reduced floor space in terms of filtration area / m2 floor space减少设备的占地面积 SEPARATION TECHNOLOGIES41HBF-vessel – 4,8 m diameter for 168 m2 and 120 m2 4.8m直径的加压仓Man Hole 1600 mm for perfect access and maintenance 1.6m 直径的大人孔 Large inspection windows (single washed) for excellent view 大直径的视窗 （带独立清洗）SEPARATION TECHNOLOGIES42On Line Moisture Measurement of cake after discharger (on request) 滤饼在线水分检测- Apply only the pressure what is necessary - Allows to optimise pressure - Wear and tear is reduced in consequence - Energy saving of compressor power 在线控制工作压力，尽量减少磨损和能耗！！！SEPARATION TECHNOLOGIES43Why should we choose Andritz HBF? 为什么我们应当选用安德里茨加压过滤机？• • • • • • • • Higher throughput 更高处理量 Lower cake moisture 更低滤饼水分 Less maintenance 更少维护量 Longer life 更长使用寿命 Higher reliability 更高可靠性 Full automatic 全自动控制 Best rate of performance/price 更高性价比 Quick after sale service 快捷的售后服务SEPARATION TECHNOLOGIES44The biggest HBF workshop in the world (Brazil) 世界最大的加压过滤车间（巴西）10 HBF filters in a row , 168 m2 each 10x168m2安德里茨加压过滤机 Feeding size: about 50% = 50μm Feeding solid: 50% w/w Throughtput: 140t DS/h each HBF168 Residual Moisture: 11-14% Filtrate: < 4g/lEnd user: Alunorte 用户 Application: Bauxite 应用：铝土矿SEPARATION TECHNOLOGIES45Test Results on RED MUD Pressure Filtration 1996 – 2007 加压过滤机赤泥试验On Pressure Filters 加压过滤• Lower Residual Moisture 更低滤饼水分• Higher Throughputs 更高处理量On Vacuum Filters 真空过滤•Dry Solids depends on type of sludge；滤饼干度取决于赤泥类型 •Slurries in South America show dryness from 22 to 25%；南美赤泥干度可达22－25％ •Slurries in China show dryness between 32 to 35%；中国赤泥干度可达32－35％ •Chemical composition (reactive surface) is of prime importance； 赤泥化学成分（表面活性）尤为重要 •Andritz tested slurries around the world; results from 22 to 35% depending on the source of sludge 安德里茨对世界各地的赤泥做过试验，滤饼水分基于赤泥性质不同可达22－35％ SEPARATION TECHNOLOGIES46Test Results on RED MUD Pressure Filtration 1996 – 2007 加压过滤机赤泥试验报告数据Pressure Filtration 加压过滤 Residual Moisture外水 24 to 35 weight - % Throughput 处理量250 to 1000 kg/m2hPressure Filtration (Washing) 加压过滤（带清洗）24 to 35 weight - % 250 to 1000 kg/m2hSteam Pressure Filtration 蒸汽加压过滤22 to 35 weight - % 250 to 1000 kg/m2h100Percentage PassingDifferential Pressure: 3 to 5.8 bar 工作压差 Dry Solids Content of Slurry: 350 to 500 g/l 入料浓度 Feed Temperature: 70 to 92 °C 入料温度80604020Test work is required for sizing equipment 0应根据试验数据进行设备选型SEPARATION TECHNOLOGIES1101001000Particle Size [μm]47Copper Floatation Concentrate (Chile) 浮选铜精矿应用（智利）4 HBF filters, 2x120m2, 2x60m2 3台安德里茨加压过滤机 Feeding size: about 80% < 37μm Feeding solid: 1450-1800g/l Throughtput: 140t DS/h each HBF120 Residual moisture: 7-9%矿山管道 输送入料 到尾矿场 浮选机 磨机 铜精矿浓缩机浮选机 加压过滤机药剂准备浮选柱控制室和试验室End user: Anglo American 用户 Application: Copper Concentrate 应用：铜精矿SEPARATION TECHNOLOGIES钼矿分选铜精矿储运场办公楼钼精矿储运场 浓缩机Las Tórtolas Plant – 工艺流程图48Copper Floatation Concentrate (Russia) 浮选铜精矿应用（俄罗斯） 1x120m2 HBF filters1台安德里茨加压过滤机 Feeding size: about 60% < 32μm Feeding solid: 1300g/l Throughtput: 100t DS/h Residual moisture: 6-7%End user: GAYSKI GOK, CIS Application: Copper Floatation ConcentrateSEPARATION TECHNOLOGIES49Hyperbaric Filter instead of Vacuum Filtration + Drying Drum (Copper) 加压过滤机取代真空过滤机＋转筒干燥机（铜矿）FiltrateFiltrate 100 t DS/h 7%FiltrateFiltrate100 t DS/h 7% Filtrate SEPARATION TECHNOLOGIES50。