模具工程常用词汇
模具专业必要的英语单词
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein |刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embeded lump|in'bed| |l mp|镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board广告牌feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder文件夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查QFD quality function deployment 质量机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂质量AOQL Average Output Quality Level 平均出厂质量Q/R/S Quality/Reliability/Service 质量/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水平等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它质量术语类QCC Quality Control Circle 品质圈QIT Quality Improvement T eam 质量改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM T otal Quality Management 全面质量管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低质量水平RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 质量改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality T arget 质量目标7QCT ools 7 Quality Controll T ools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 质量系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-CompaqS-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 数据中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)标识符SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘驱动器HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement 4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略质量保证DQA Desigh Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk T op 卧式(机箱)MT Mini-T ower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 扁平电缆PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM T otal Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA T o Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Sizeugboss模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架。
模具专业术语
模具专业术语————————————————————————————————作者：————————————————————————————————日期:ﻩ模具专业术语——注塑模(锦浩塑胶模具厂)EngｌisｈTraｉninｇ——Iｎjectｉon Mｏld（一）模具专业基本用词Ｐrofesｓional Ｔeｒms１.塑料—ｐlａstic, resin2．样件—ｓample3. 钢料—sｔeeｌ４. 注塑机—injecｔion mａchine, pｒesｓ５．产品—paｒt, prｏdｕct, mouldiｎg６．模具—mold, moｕlｄ, toolＡ简易模（样板模)—prototype mold Ｂ量产用模具—proｄuctio ｎmｏld7. 三维造型(数模）—modeｌ, 3D dａｔa8．二维产品图—2Ｄparｔdrawing９. 设计—ｄesｉｇn10．制造—ｍanufａcture, build ｕp, construction１1．检验—cheｃk, ｉnｓpeｃtｉｏn12.测量—measｕre，inspecｔion13.修改—chａnge, mｏｄify, ｃoｒrection14. 工程更改—ｅnｇineer cｈange１5．质量—qｕality１６. 数量—quantiｔy17. 基准—ｄａｔuｍ, ｒefeｒｅnｃe（二)如何解析2D 产品图？Ｈow tｏread 2D part drａwing？一. 产品几何Geoｍｅtry1．点—poinｔ2.线（边）—line, ｅdge3.面faｃeA 侧面—siｄｅB 表面—ｓurfaceC 外观面—aｐｐeａrａnｃｅsｕrfａｃe4．壁厚—ｗall thｉｃkneｓs, stoｃk thicknesｓ5．加强筋(骨位）—rib6.孔—hole7．细长的槽—sloｔ8．柱位—boss9.角—coｒnerA 圆角—ｆiｌｌｅｔB 倒角—chaｍferＣ尖角—sharp cｏrnｅr10.斜度—anglｅ，taper1１. 凹槽—rｅceｓs ,groove二. 分模信息Spliｔtiｎｇ1．分型线—parｔing line (Ｐ/L), splitｔiｎg lｉne２. 主分模方向—main directｉon, ｌiｎe of draｗ3．浇口设定—ｇatiｎg三. 产品标识Pａrt Iｄeｎtificａtion1. 产品名称—part nａｍe (Ｐ/N)２.产品编号+版本号—paｒt numbｅr ＋revisioｎ（Rｅv.）3. 型腔号—cａvitｙnuｍber4.材料标记—material symbol5. 模具编号—moｌd numbeｒ(no.）6．日期印—ｄatingｉnserｔ, date code7. 循环印—ｃycｌiｎg code8.公司标志—coｍpany loｇo四. 技术要求Sｐecificatioｎ(SpｅciaｌRｅquiｒement)1.项目启动表Kｉcｋ-ofｆshｅｅt１）项目名称—progrａｍname,projｅct naｍe2)产品名称—part namｅ, pｒoduct ｎame, part descriptｉｏn３) 产品编号—ｐart ｎuｍbeｒ(P/N)4) 客户模号—cｕstoｍer mold no.5) 项目启动日期— kick off dａtｅ，starｔdatｅ6)项目完成日期— duｅ dａte, lead tｉｍｅ7) 内模件用钢—ｔool sｔｅｅｌ8）型腔数量—numｂer of cavit iｅs９)数模文件编号—data.10）注塑材料—rｅsin，plastic, raw maｔｅrial1１）收缩率—ｓhrink, ｓhrinkage,sｈrink ｆactoｒ12)注塑机吨位—ｍoldｉng mａchine sｉzｅ， injeｃｔｉon machiｎe size １３）成型周期—cyｃle time14)型腔光洁度—caｖiｔy pｏlish1５) 型芯光洁度—core polｉｓh16）皮纹(晒纹)—tｅxｔurｅ, gｒain17）拔模斜度—dｒaft anｇle, ｒemoval ｔaper18）注塑件颜色及光泽—molｄeｄｃｏｌoｒ& ｇloss19) 模具加工地—manｕfａｃturing ｆaｃility２０）热流道供应商—maniｆｏｌd mａnuｆactureｒ, ｍａｎifolｄ supplieｒ2１)浇口位置—gaｔe ｌoｃation ／pｏｓitｉon22) 浇口类型—gａtｅtype23) 产品标识—stamp infｏrmaｔion, parｔidentificａtion２４）特殊要求—sｐeciaｌ instructiｏｎs2. 产品质量及外观要求Pａrt Quality & Apｐｅaraｎcｅ１）尺寸及公差Dｉmensioｎ&Toｌｅｒancｅ①重要尺寸—ｃritical dimensｉoｎ,importanｔdiｍ.，kｅy dim.②理论尺寸—ｎｏｍiｎalｄimension③实际尺寸—actuａｌdiｍension④公差—tolｅraｎce⑤公差带—tｏlｅrancｅrａnge⑥尺寸超差—dimensionｄeviａtion⑦接受（合格）—ａccepｔ, OＫ⑧拒绝(不合格）—rejecｔ, refｕse,oｂsolete,NＧ⑨让步接受—conceｓsion, ｓｐecial adｍiｔ⑩返工—re-wｏrk２）产品缺陷（较常见）Ｄefeｃts (normaｌ）①缩印—sｉnk mark, sｈrｉｎｋage②飞边—flａsh, burr③段差—mｉsmａtcｈｄｉｓcｒepancy④银丝纹—ｓｎake ｍaｒks, streak⑤弯曲—warpａｇe, ｄistoｒtion⑥打不足（缺料）—shorｔｓhot⑦熔接线—wｅld lｉne3．产品外观ParｔAｐｐearanｃｅ①产品颜色—paｒｔｃｏｌor②产品光泽—ｇloss③皮纹粒度—gｒain4．常用词汇、词组及短语NormａｌＷｏrd, Shｏｒt Seｎｔｅｎｃe1）单边—per side2)双边—both sides３) 加入,添加—aｄｄ,iｎcorporａtｅ４) 去除，取消—rｅmovｅ,ｃancel５) 满足…的要求,符合,与…要求一致—accｏｒｄing ｔｏ, conｆorｍto, satisfy, mｅeｔ6) 要求，需要—ｒequｉrｅ,neｅｄ,demanｄ7）确认—be ａｐproｖｅｄ, agreedｂy …8) 允许—peｒmｉｔ，ａlloｗ9) 在…范围之内—ｗithin1０）不可以,不允许，禁止—free from，preｖent, avｏid11）…,除非有另指—…unleｓsｏtherwｉｓｅspecified1２）…或少于—…or ｌess13) 自动化运作—automatiｃoperａｔｉoｎ１4）未注尺寸(详细形状）见三维造型Noｎｄimensioned ｃontｏur (dｅｔａiled ｓhape) ｓｅe ３D mｏｄel.15)分型线上的飞边(披缝)或段差应小于…Bｕrrs and diｓｃrｅpａｎcy onｔheＰ／Ｌshaｌl be… ｏr less.五．标题栏Titｌe Bloｃｋ１. 产品名称—part name２．图纸编号+ 版本号(索引号）—draｗｉng no．+ level （ｉndex)3. 一般公差[的标准] —generａl tolerａnｃe（三) 如何阅读制模标准？Hｏw to read toｏling stanｄaｒd?一．模具结构术语Moｌd CｏnsｔrｕctiｏｎTermiｎologyA．模架Mold Ｂａｓe1.模架量化特征Mｅasuremｅnt Feature①长X 宽Ｘ高—ＬeｎgtｈXＷidth X Height②模具推高尺寸（模厚）—sｔａck hｅiｇht ｏf ｍould③模具重量—totａl weight ofｍould,mouｌd thｉｃkｎesｓ2. 定模底板—fｒont pｌaｔe, ｔｏｐclamｐiｎｇplａte, cｌamｐpｌatｅ，clａmｐinｇplate３．定模板—cａvｉty plａｔe，fixｅd moｕlｄplａte, A – platｅ4. 动模板—cｏｒe plａｔe,ｍoｖing mｏｕｌd ｐlate, B – plate５. 支撑板—ｓuppｏｒt plａte, baｃking ｐlate6. 模脚—support bloｃks，raｉlｓ，riseｒs, spａｃeｒblｏｃk７. 顶杆固定板—reｔaining ｐｌatｅ, ejector retainｉｎg plate８. 顶板—ejｅctor ｐlaｔe9．动模底板—baｃｋpｌａte1０．导柱—ｇｕｉde ｐillar, leａｄer pin, ｇuｉdeｐin11．导套—gｕidｅｂuｓh, ｌeadｅr ｐｉnｂush12.复位杆—rｅturn piｎ，push-back ｐｉｎ13．弹簧—ｓpriｎｇ14. 撑头—supｐｏrt pillar１5．推板导柱、导套—ejectiｏn gｕidｅpｉn / ｂush16．挡钉—ｓtop ｐiｎ,stoｐ buttoｎ１７．站立脚—sｔａndiｎg-ofｆpiｌlars18．标牌—pｌaquｅscutcheonB.成型零部件moｕｌding components1９. 型芯—cｏre20．型腔—cavitｙ２1. 镶针—core ｐin２２. 镶块—insｅrt，sｐlit23.滑块—sｌide, sliｄiｎｇsｐlit２4. 斜顶—lifteｒ,angled-liｆt ｓｐlitA 斜顶头—lｉftｅr hｅadB 斜顶杆—ｌifter rod, lｉｆteｒｓｈａft2５. 成型顶杆—ｍoulding facｅpin, form pｉｎC．浇注系统Fｅed System1．塑料Mouldingａ．主流道—ｓｐrueｂ. 分流道runｎer①主分流道— mａin ruｎner ②二级分流道— braｎcｈ rｕnｎeｒ分流道断面形状cｒosｓ-sｅｃtional ｓｈape oｆｒunner①圆形—ｆuｌl roｕｎd②半圆形—semiciｒcｕｌar③梯形—trapｅｚoidaｌｃ．浇口gaｔｅ常用浇口形式nｏrmａl ｇate tyｐe :①边缘浇口（J型浇口) —eｄgｅｇate, J –ｇate②侧浇口—side gate③潜伏式浇口—sub-gaｔe, ｃａshew gatｅ， subsurfａｃｅ gaｔe, suｂmaｒine gaｔe④潜伏式二次浇口(隧道式浇口) —ｔunnｅl gａｔe ontｏfeｅｄer post⑤点浇口—pｉn gａｔe⑥直接浇口(主流道型浇口) —ｓprue gate, direct gａte⑦护耳式浇口—tａb gａted. 模腔—imprｅｓsｉｏnｅ. 冷料井—colｄsｌug welｌf．热流道—hot runner２.模具零件moｌｄcoｍponentsa. 定位圈—lｏｃating ring, lｏｃation ｒing, regｉsｔｅr riｎｇb. 浇口套—spｒue bushc．挡圈—sｔｏp ｒingd．浇口镶块—gate inｓeｒte．热流道板—mａｎifoldｆ. 热嘴—ｈｏｔｄropＤ.分型面及其锁紧、排气Paｒtｉｎg Sｕrfaｃｅ, inter-loｃking＆ventｉng 1．分型线—paｒtｉnｇline ( P/Ｌ）２. 镶拼线—bｏdｙlｉnｅ，ｊoiｎt lｉne3．平/不平的分型面—ｆlａt ／non – flaｔ pａrting sｕrface4．封胶面—sｈut ofｆsurfaces, ｓeａｌ－ｏff suｒfａceｓ5．擦位—shuｔoff6. 碰穿位—kiｓs-ｏff7. 管位—pａrtｉｎgｌinｅｌock８.分型面的释放(避空) —rｅｌieｆｏｆpａｒtiｎg ｓuｒｆａｃe９．分型面的平衡—bａlanｃiｎｇof ｐarｔing ｓurface10．锁紧角度—ｌockｉng anglｅ1１.锁紧力—cｌａｍpingｆoｒce1２．锁模板—safetｙstｒap1３．精定位—Inｔeｒloｃk,die locｋ14．困气—aｉｒtrap1５．排气槽—vent, veｎt ｓlｏtＥ.滑块机构Slide１．驱动Acｔuaｔｉｏｎ①斜导柱—anglｅｄｐin, ｈorn pｉn, cａm pin②弹簧—sprinｇ③油缸—ｈydraulｉc cyliｎder２．制动Dｅｔeｎtion①滑块固定器—sｌide rｅtａｉｎer②弹簧制动器—spｒing-loaded detentｉon (plunger)③挡钉、挡板—ｓtop pin, stop platｅ, slide stop3．导轨—gｉｂ,gｕide sｔrip4．锁紧块(楔紧块)—heel blｏcｋ,ｌｏcking ｈｅel，wｅｄge blｏｃk, cｈasｅbl ｏｃk5. 耐磨片—wear pｌａte，ｗｅar strip6. 压板—reｔaiｎeｒ7. 螺钉—screw８．定位销—dowelＦ.斜顶机构Ｌiftｅｒ1.斜顶头—lｉfｔｅｒｈeａｄ2．斜顶杆—liｆtｅr roｄ，lifｔer ｓhａfｔ3．开口销—spｌit ｐin4．固定板(压板) —reｔaiｎer plａｔｅ5. 耐磨片—wear ｐlatｅ６. 铜导套—ｂrｏnzｅbuｓhing7．衬套—spaｃeｒ８. 导轨—L – gib9. 滑动块—slideG．顶出系统EjectioｎSyｓtem１. 基本词汇Baｓｉc Worｄ①顶出行程—ejectｉｏn stroke②模具开档—ｄayligｈt③粘模—stｉck④产品脱模—part iｓpuｓh ofｆfrom,ｃlearｐart of mouｌd, seｐaratioｎofｐart2. 顶板机构Ejector pｌａｔe asｓembly①顶板(推板) —ｅｊｅｃｔoｒplａtｅ②顶板固定板—retａiniｎg plａte③推板导柱—ejector gｕiｄｅpin④推板导套—ｅjｅctor guide ｂusｈ⑤撑头—supｐort pｉllar, pilｌarｓupport3．复位机构Return Sｙsteｍ①复位杆(回程杆)—return ｐin，ｐush – back pin②挡钉—sｔｏｐpin, sｔop buｔton③压簧—coｍpｒｅsｓeｄsｐring④碟簧—a sｔack of “Ｂeｌleviｌｌｅ”wasｈers⑤早复位机构—ｅａrly return sｙsｔem⑥强制复位机构—posｉtｉve retｕrｎsｙsteｍ4．顶出方法Ejection Techniqｕes１) 顶杆顶出—ｐiｎeｊection２) 顶管顶出—ｓleｅve ejｅction3）顶块顶出—bａr ejｅction４) 扁顶顶出—bｌａde ｅｊｅction５) 顶板顶出—ｓtripper eｊecｔｉon６) 油缸顶出—hydraｕlic ejｅctｉｏn7) 气顶—air ｅjectioｎ8）阀门顶出—valve ejｅｃtion5. 顶出元件Ejecｔｉon Eｌｅments1) 拉料杆—spｒue pｕｌlｅr，sｕckerｐin2) 顶杆—ejector pｉｎ3) 阶梯式顶杆—ｓｔeppｅd eｊｅctor ｐin4) 顶管—eｊeｃtion sleｅｖe，slｅevｅ５）扁顶—ｅjｅcｔor blaｄe, slａbｂeｄoff ejecｔｏr pin6）顶块—striｐper bar7）顶环—strippｅr ｒing８)推板—ｓtripper plate9)加速顶—accｅleｒaｔｅd ejeｃtioｎ6. 顶出辅助机构Supｐlｅmｅntaryｏpｅraｔｉng sysｔem1）弹簧柱塞器—sprｉnｇ–ｌoａdｅｄｐｌunger２）弹珠定位器—baｌl catch ｓyｓtem3) 插销式锁扣—Lａtch– lock4) 尼龙拉杆装置—fｒiｃtion pullｅr ｄeｖice７．电器元件Electrｉc Coｍpｏnents1) 压力传感器—pｒessuｒe trａｎｓduｃer2) 限位开关—ｌimit swｉtchF．冷却系统Ｃooling Ｓysｔem1. 基本词汇BａsiｃWｏrd１)温差—teｍｐerａture variａtion2) 水孔（水道）—ｗaｔｅrｌines, wａtｅr-waｙｓ, flｏw-wａy, cｈannel3) 水路—ｃｏolｉng ciｒcuit4) 水路示意图—wateｒsｃhｅmａtｉc，ｓchematic circuit5) 冷却液—cｏｏlaｎt，coｏlant fluid６）内连接—iｎｔercｏnnｅct7) 外连接—eｘteｒnaｌｃｏｎnectioｎ8）出口、入口—oｕtlｅt、iｎleｔ9) 漏水—ｗａter ｌeakage2. 水路分布Circｕits1)阶梯式水路—steppeｄsyｓteｍ２)喷淋—bａffled holeｓｙstem3) 斜孔式水路—angled hole sｙｓtem3. 水路元件Ｃoｍｐonents1）闷头（螺塞、止水栓) — (threａdlesｓ)brasｓpressure pｌuｇ:feｍale plug & male2）隔水片—bafflｅ3) 密封圈—O – rinｇ4）快插水路接头—ｑuick disconｎｅcｔｆｉｔtinｇ, qｕick coｎneｃｔi ｏｎadaptor5) 弯头—elｂｏｗ６)偶合器（连接器、接头) —adapｔor （iｎcｌｕding a plug & a sｏcket）7）橡皮管—rubbｅｒｈoｓｅ８)分水板—water mａnｉｆolｄG.螺纹、螺纹孔& 螺钉Tｈread,tｈｒead ｈole & ｓcrｅｗ1．螺纹—threａd２. 管螺纹—pipe thｒeaｄ3．螺纹孔—screｗｈｏｌe, tappｅd hｏle4. 起吊孔—ｈandｌｉｎg holｅ, jack scｒｅw hole, eyｅbolt hole５.螺钉—screw6．内六角螺钉—sockeｔheａded cap sｃrｅｗ（s．h.c.s.）7．沉头螺钉—ｆlat headed ｃaｐscrew （f．ｈ.c.s）８. 螺栓—bｏlｔ, eyｅbｏｌｔ9．螺母—ｎuｔ10.锁紧螺母—lｏcknut１1．螺纹标准Tｈｒead Stａｎdａrd①公制标准—Metric②英制标准—Imｐｅｒｉal③英制管螺纹标准—Bｒiｔｉsh Ｓtａndard Ｐｉpe thread （BSP)④美制管螺纹标准—ＮPＴ⑤美制粗螺纹标准—UｎitｅｄCoarse tｈｒeａｄ（UNＣ）⑥美制细螺纹标准—Ｕnｉted Fｉnｅtｈrｅａd（ＵNＦ）H．润滑Ｌubricatiｏn１．润滑槽—greａｓe grooｖe２．加油管—grｅａsｅlｉｎe3．油杯—luｂriｃａtioｎfittｉngI．测量仪器Ｍｅasuring Iｎsｔrｕmｅntｓ1. 游标卡尺—vernierｃaliper2. 千分尺—ｍicrｏmeter3.高度规—ｈeｉght gauｇｅ４. 刻度规—ｄiａｌｇａuge5．三坐标测量仪—Coordinaｔe Ｍeasuｒe Maｃhiｎｅ（CＭM）6．塞规—piｎgauge７．圆角量规—radii gauｇe8．輪廓投影機—proJ.注塑机参数Ｉｎjectｉon MacｈｉｎｅPａrameter1. 注塑机规格参数Ｉｎjecｔiｏn MachineＳpeｃifｉｃation①锁紧类型ｃlamp typea.油缸—hydｒauｌic ｂ．肘杆式—togｇle②垂直注塑机导柱间距—tie baｒverticalｃlｅarance③水平注塑机导柱间距—tie bar hoｒizonｔａlｃｌearancｅ④台板尺寸—platenｄim.⑤最小/最大模厚—molｄheighｔMiｎ. / Mａx., Min./ Max. moldｔhickｎess⑥最小／最大注塑机开档—ｏpen daｙliｇht Min. ／Max.⑦锁紧行程—ｃlamｐsｔroke⑧锁紧力—clampｉng forｃe⑨顶出行程—ejector stroke⑩顶出力—ejector forｃe２. 试模工艺参数Mouｌdiｎg ProcessＰaｒameter，macｈine setting①时间Ｔimer(TM)，seca. 注塑(充填）时间—fｉｌling time, iｎjｅctｉon timeb．冷却时间—cｏolｉnｇtimec. 补缩时间—ｐacｋinｇtimｅｄ.保压时间—holding ｔiｍee. 成型周期—cyｃｌe time②速率、速度Ｖelocｉｔy, ％、spｅed，in/seca．注塑（充填)速度—iｎjectiｏn sｐｅedb．保压速率—ｈｏld pressure velocitｙc．螺杆转速—screw rotatioｎｓｐeed③压力Pressｕｒe(Ｐrs．), psiａ. 注塑压力—ｉｎｊeｃtioｎpressurｅb. 保压压力—ｈoｌd prｅssuｒec．回压(背压）—bａｃk prｅｓsure④温度Temｐeratｕre(Teｍp．）, °Fa．注塑机喷嘴温度—nｏzzlｅｔｅmp.b．料筒前段、中段、后段温度—barrel ｆrｏnt、middle、rear temp.c．模温—mouldｔemp.d．料温—purgｅd resin melt ｔemp．ｅ．空射料温—air sｈot melt tｅmｐ.。
模具专业词汇中英文对照表
模具专业词汇中英文对照表1. 模具材料（Mould Materials）•合金钢（Alloy Steel）•不锈钢（Stnless Steel）•工具钢（Tool Steel）•铸造铁（Cast Iron）•铝合金（Aluminum Alloy）•铜合金（Copper Alloy）•硅橡胶（Silicone Rubber）•塑料（Plastic）•陶瓷（Ceramic）2. 模具零件（Mould Components）•模板（Mold Base）•注塑装置（Injection Unit）•顶出器（Ejector）•气嘴（Nozzle）•间隙（Clearance）•提位器（Lifter）•滑块（Slide）•定位圈（Locating Ring）•膜背（Backing Plate）•挡块（Stop Block）•压板（Clamp Plate）•冷却管（Coolant Pipe）•驱动装置（Drive Unit）3. 模具制造工艺（Mould Manufacturing Process）•设计（Design）•切割（Cutting）•加工（Machining）•组装（Assembly）•调试（Debugging）•精修（Finishing）•表面处理（Surface Treatment）•检查（Inspection）•试产（Trial Production）4. 模具加工方式（Mould Processing Methods）•铣削（Milling）•磨削（Grinding）•拉刀（Planing）•镗削（Boring）•钻孔（Drilling）•线切割（Wire Cutting）•抛光（Polishing）•火花加工（EDM）5. 模具设计要点（Key Points in Mold Design）•壁厚（Wall Thickness）•浇注系统（Gating System）•冷却系统（Cooling System）•排气（Venting）•气罩（Bubbler）•顶杆（Ejector Pin）•脱模斜度（Draft Angle）•零件坯料与尺寸（Blank and Dimensions）•对位方式（Alignment Method）•衬套（Insert）•翻制（Flip Mold）•分模（Split Mold）6. 模具维护与保养（Mold Mntenance）•模具清洁（Mold Cleaning）•润滑（Lubrication）•排浆（Purging）•磨损修复（Wear Repr）•抛光修复（Polish Repr）•零件更换（Component Replacement）•修复记录（Repr Record）•数字化管理（Digital Management）7. 模具常见故障及解决方法（Common Mold Faults and Solutions）•翘曲（Warping）•缺陷（Defects）•泛油（Flash）•磨损（Wear）•烧坏（Burning）•掉件（Part Ejection）•插损（Insert Damage）以上仅是模具专业领域常用词汇的一个简单对照表。
模具常用英语
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punch 冲床robot机械手hydraulic machine液压机lathe车床planer刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president总裁general manager总经理special assistant特别助理factory director厂长department director部长deputy manager =vice manager副理section supervisor课长deputy section supervisor =vicesection supervisor副课长group leader/supervisor组长line supervisor拉长assistant manager助理to move, to carry, to handle搬运be put in storage入库packing包装to apply oil擦油to file bur 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scrape 报废scrape v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturingprocedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产能力education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die复式压模die locker锁模器pressure plate=plate pinch压板bolt螺栓general affairs dept总务部automatic screwdriver电动起子thickness gauge厚薄规fixture治具power wire电源线buzzer蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers无指手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把cleaner/dust collector吸尘器rag 抹布garbage container灰箕dustbin垃圾箱garbage bag垃圾袋chain链条elevator升降机production line流水线/生产线magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screwhead螺丝滑头slipped screwhead/slippery screwthread滑手speckle斑点mildew（动）=moldy（形）=mouldy发霉rust生锈deformation变形bur(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage收缩mixed color杂色scratch划伤poor processing 制程不良poor incoming part来件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration变色water spots水渍surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan=enterpriseexpansion projects企划QC（Quality Control）品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification分类regulation整顿cleanness清扫culture教养qualified products,up-to-gradeproducts良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶篮plastic basket塑胶筐isolating plate/baffle plate;barricade隔板carton box纸箱stretch拉深blanking落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotate speed, rev转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch-to throw-over switching over切换stage die工程模automation自动化to stake, staking铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊stamping, punch冲压punch, dieing out press冲床uncoiler & straightener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivery to.to send delivery backto retern of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损chamfer倒角character die字模career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to loose a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档blanking die冲裁模progressive die 连续模compound die复合模punch冲孔panel board镶板trimming切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘first check初盘复核second count 复盘equipment设备waste materials废料work in progress product在制品casing = containerization装箱second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected 进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventorylist备品盘点清单spare molds location模具备品仓skid/pallet栈板EDM放电机coil stock卷料sheet stock片料tolerance公差score=groove压线cam block滑块pilot导正筒trim剪外边pierce 冲孔pocket for the punch head挂钩槽feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection新品首件检查FAA first article assurance 首件确认TVR tool verification report模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality ControllTools 品管七大手法通用之件类ECN Engineering Change Notes工程变更通知(供应商)ECO Engineering Change Order工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process制程检验规格SOP Standard OperationProcedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionInspect 高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material Condition LMS Least Material Size 模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形 rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shellcasting 壳模铸造foam forming ?泡成形sinterforging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形 warmforging 温锻investment casting 熔模铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具burnishing die 挤光模landedpositive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswtbending die 双折冷弯模具extrusion die 挤出模 palletizingdie 叠层模family mold 反套制品模具 plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具 pressuredie 压紧模fishtail die 鱼尾形模具 profiledie 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coilspring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢diaphragmgate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin顶出梢ejector plate 顶出板 ejector rod顶出杆ejector sleeve 顶出衬套 ejectorvalve 顶出阀eye bolt 环首螺栓 filling core椿入蕊film gate 薄膜形浇口 finger pin指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头headlesspunch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injectionram 压射柱塞inlay busher 嵌入衬套innerplunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockoutbar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套liftingpin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush活动衬套making die 打印冲子manifoldblock 歧管档块master plate 靠模样板matchplate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板movingbolster 换模保持装置moving bolster plate 可动侧模板。
常用模具英语词汇
模具述语 一、入水：gate进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner热流道： hot runner, hot manifold 热嘴/冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line plug 喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件： mold components撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：sprue spreader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks活动臂：lever arm 复位键、提前回杆：early return bar三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L ：guide pin顶针板：ejector retainer plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar slot内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate缩呵：movable core, ret urn core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate气阀：valves 斜导边：angle pin 术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut height 顶针碰运水：water line interferes with ejector pin 料位出上/下模：part from cavity (core) side 模胚原身出料位：cavity direct cut on A-plate, core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliminary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability, stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thermo expansion公差：tolerance铜公(电极）：copper electrodeArrest biock storage area 挡块放置区Micrometer strorage area 分厘卡放置区Unprocessed copper 未处理铜工Processed copper 处理铜工Rough machine 粗加工Finish machine 精加工。
模具专业英语词汇
Injection Mold Technical Terms（一）模具专业基本用词Professional Terms1．塑料—plastic, resin2．样件—sample3．钢料—steel4．注塑机—injection machine, press5．产品—part, product, moulding6．模具—mold, mould, toolA简略模（样板模）—prototype mold B量产用模具—production mold 7．三维造型（数模）—3D model, 3D data8．二维产品图—2D part drawing9．设计—design10．制造—manufacture, build up, construction11．查验—check, inspection12．丈量—measure, inspection13．改正—change, modify, correction14．工程改正—engineer change15．质量—quality16．数目—quantity17．基准—datum, reference牛角入水 -rads?gate（二）怎样分析2D 产品图？ How to read 2D part drawing?一．产品几何 Geometry1．点— point2．线（边）—line, edge3．面 faceA侧面—side B表面—surface C外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．增强筋（骨位）—rib6．孔— hole7．修长的槽—slot8．柱位—boss9．角— cornerA 圆角—fillet B倒角—chamfer C尖角—sharpcorner10．斜度— angle, taper11.凹槽—recess , groove二．分模信息 Splitting1．分型线— parting line (P/L), splitting line2．主分模方向—main direction, line of draw3．浇口设定—gating产品表记 Part Identification1．产品名称—part name (P/N)2．产品编号 +版本号—part number + revision (Rev.) 3．型腔号— cavity number4．资料标记—material symbol5．模具编号—mold number (no.)6．日期印— dating insert, date code7．循环印— cycling code8．企业标记—company logo三．技术要求 Specification (Special Requirement) 1．项目启动表 Kick-off sheet1）项目名称—program name, project name2）产品名称—part name, product name, part description 3）产品编号—part number (P/N)4）客户模号—customer mold no.5）项目启动日期—kick off date, start date6）项目达成日期—due date, lead time7）内模件用钢—tool steel8）型腔数目—number of cavities9）数据文件编号—data file no.10）注塑资料—resin, plastic, raw material11）缩短率—shrink, shrinkage, shrink factor12）注塑机吨位—molding machine size, injection machine size 13）成型周期—cycle time14）型腔光洁度—cavity polish15）型芯光洁度—core polish16）皮纹（晒纹）—texture, grain17）拔模斜度—draft angle, removal taper18）注塑件颜色及光彩—molded color & gloss19）模具加工地—manufacturing facility20）热流道供给商—manifold manufacturer, manifold supplier 21）浇口地点—gate location / position22）浇口种类—gate type23）产品表记—stamp information, part identification24）特别要求—special instructions25）安全模数—safe steel2．产质量量及外观要求Part Quality & Appearance Requirement 1）尺寸及公差 Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实质尺寸—actual dimension④公差— tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受（合格）—accept, OK⑧拒绝（不合格）—reject, refuse, obsolete, NG⑨退步接受—concession, special admit⑩返工— re-work2）产品缺点（常有的） Defects (normal)①缩水— sink mark, shrinkage②飞边，毛边—flash, burr③段差— mismatch discrepancy④银丝纹，蛇纹—snake marks, streak⑤曲折，变形—warpage, distortion⑥打不饱（缺料）—short shot⑦熔接线—weld line⑧多胶— unwanted plastic⑨拉伤— damage3．产品外观 Part Appearance①产品颜色—part color②产品光彩—gloss③皮纹粒度—grain4．常用词汇、词组及短语Normal Word, Short Sentence1）单边— per side2）双边— both sides3）加入，增添—add, incorporate4）去除，撤消—remove, cancel5）知足的要求，切合，与要求一致—according to, conform to, satisfy, meet 6）要求，需要—require, need, demand7）确认— be approved, agreed by8）同意— permit, allow9）在范围以内—within10）不能够，不同意，严禁—free from, prevent, avoid 11），除非有另指—unless otherwise specified12）或少于—or less13）自动化运作—automatic operation14）未注尺寸（详尽形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于Burrs or discrepancy on the P/L shall be or less.四．标题栏 Title Block1．产品名称—part name2．图纸编号 + 版本号（索引号）—drawing no. + level (index) 3．一般公差—general tolerance（三）怎样阅读制模标准？How to read tooling standard?一．模具构造术语Mold Construction TermsA．模架 Mold Base1．模架量化特点Measurement Feature①长 X 宽 X 高— Length X Width X Height②模具高度尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness2．定模底板—front plate, top clamping plate, clamp plate, clamping plate 3．定模板—cavity plate, fixed mould plate, A–plate4．动模板—core plate, moving mould plate, B–plate5．浮动板—floating plate6．支撑板—support plate, backing plate7．间隔板 , 方铁— support blocks, rails, risers, spacer block8．顶杆固定板—retaining plate, ejector retaining plate9．顶板—ejector plate，bottom clamping plate10．动模底板—back plate11．导柱—guide pillar, leader pin, guide pin 12．导套—guide bush, leader pin bush13．复位杆—return pin, push-back pin14．弹簧—spring15．撑头—support pillar16．顶针板导柱、导套—ejection guide pin / bush 17．垃圾钉—stop pin, stop button18．模脚—standing-off pillars19．标牌—plaque scutcheonB．成型零零件 moulding components20．型芯—core insert21．型腔—cavity insert22．镶针—core pin23．镶块—sub-insert, split24．滑块— slide, sliding split25．斜顶— lifter, angled-lift splitA 斜顶头— lifter head B斜顶杆— lifter rod, liftershaftC斜顶连结块——lifter coupling D斜顶导向块——lifter guideE斜顶导滑块——lifter Gib26．成型顶杆—moulding face pin, form pinC．浇注系统 Feed System1．塑料 Plastica．主流道—sprueb．分流道 runner①主分流道—main runner② 二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形— full round②半圆形—semicircular③梯形—trapezoidalc．浇口 gate常用浇口形式 normal gate type :①边沿浇口（ J 型浇口）—edge gate, J–gate②侧浇口—side gate③潜藏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针— subgate to pin④潜藏式二次浇口 ( 地道式浇口 ) — tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口 ( 主流道型浇口 ) — sprue gate, direct gate⑦护耳式浇口—tab gated．模腔— impressione．冷料井—cold slug wellf ．热流道—hot runner2．模具零件 mold componentsa．定位圈—locating ring, location ring, register ringb．浇口套—sprue bushc．挡圈—stop ringd．浇口镶块—gate inserte．热流道板—manifoldf ．热嘴— hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting 1．分型线— parting line ( P/L )2．镶拼线— bodyline, joint line3．平 /不平的分型面—flat / non–flat parting surface 4．封胶面— shut off surfaces, seal-off surfaces5．擦穿位— shut off6．碰穿位— kiss-off7．管位— parting line lock8．分型面的开释 ( 避空 ) — relief of parting surface 9．分型面的均衡—balancing of parting surface 10．锁紧角度—locking angle11．锁紧力—clamping force12．锁模块—safety strap13．精定位—Interlock, die lock14．困气—air trap15．排气槽—vent, vent slot16．撬模坑--- pry slot17．计数器--- shot counter/ cycle counterE．滑块机构 Slide1．驱动 Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧— spring③油缸— hydraulic cylinder2．制动 Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3．导轨— gib, guide strip,center guide4．锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block,slide driver5．耐磨片— wear plate, wear strip6．压板— retainer,gib7．螺钉— screw8．定位销— dowel pin9．行位扣— slide lock / slide retainer10．?flat ejector pin?扁顶针F．斜顶机构 Lifter1．斜顶头— lifter head2．斜顶杆— lifter rod, lifter shaft 3．斜顶固定块— lifter rod retainer 4．斜顶导向块— lifter guide5．张口销— split pin6．固定板（压板）—retainer plate 7．耐磨片— wear plate8．铜导套— bronze bushing9．导套固定板— bushing retainer 10．衬套—spacer11．导轨—L–gib12．导轨---T-Gib13．滑动块—slide14．连结块—U-CouplingG．顶出系统 Ejection System1．基本词汇 Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模— stick on④产品脱模—part is push off from,clear part of mould, separation of part2．顶板机构 Ejector plate assembly①顶板— ejector plate②顶板固定板—retaining plate③推板— stripper plate④推板导柱—ejector guide pin⑤推板导套—ejector guide bush⑥撑头— support pillar⑦限位块— stop block,stroke block3．复位机构 Return System①复位杆（回程杆）—return pin, push–back pin②垃圾钉— stop pin, stop button③压簧— compressed spring④碟簧— a stack of“Belleville” washers⑤早复位机构—early return system⑥强迫复位机构—positive return system4．顶出方法 Ejection Techniques1）顶杆顶出—pin ejection2）顶管顶出—sleeve ejection3）顶块顶出—bar ejection4）扁顶顶出—blade ejection5）顶板顶出—stripper ejection6）油缸顶出—hydraulic ejection7）气顶— air ejection8）阀门顶出—valve ejection5．顶出元件 Ejection Elements1）拉料杆—sprue puller, sucker pin2）顶杆— ejector pin3）阶梯式顶杆—stepped ejector pin4）顶管— ejection sleeve, sleeve5）扁顶— ejector blade, slabbed off ejector pin 6）顶块— stripper bar7）顶环— stripper ring8）推板— stripper plate9）加快顶—accelerated ejection10）直顶 ----straight lifter/EJECTOR BAR6．顶出协助机构 Supplementary operating system1）弹簧柱塞器—spring–loaded plunger2）弹珠定位器—ball catch system3）插销式锁扣—Latch–lock4）尼龙拉杆装置—friction puller device7．电器元件 Electric Components1）压力传感器—pressure transducer2）限位开关—limit switchF．冷却系统 Cooling System1．基本词汇 Basic Word1）温差— temperature variation2）水孔（水道）—waterlines, water-ways, flow-way, channel 3）水道— cooling circuit4）水道表示图—water schematic, schematic circuit5）冷却液—coolant, coolant fluid6）内连结—interconnect7）外连结—external connection8）出口、进口—outlet、inlet9）漏水— water leakage2．水道散布 Circuits1）阶梯式水道—stepped system2）分开板水道—baffled hole system3）斜孔式水道—angled hole system3．水道元件 Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male2）隔水片—baffle3）密封圈—O–ring4）快插水道接头—quick disconnect fitting, quick connection adaptor5）弯头— elbow6）巧合器（连结器、接头）—adaptor (including a plug & a socket) 7）橡皮管—rubber hose8）分水板 , 集水块— water manifoldG．螺纹、螺纹孔& 螺钉 Thread, thread hole & screw1．螺纹— thread2．管螺纹— pipe thread3．螺纹孔— screw hole, tapped hole4．起吊孔— handling hole, jack screw hole, eye bolt hole5．螺钉— screw6．内六角螺钉—7．沉头螺钉—8．螺栓— bolt9．螺母— nut10．锁紧螺母—locknut11．螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread（BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread（UNC）⑥美制细螺纹标准—United Fine thread（UNF）H．润滑 Lubrication1．润滑槽— grease groove2．加油管— grease line3．油杯— lubrication fittingI ．丈量仪器 Measuring Instruments1．游标卡尺—vernier caliper2．千分尺— micrometer3．高度规— height gauge4．刻度规— dial gauge5．三坐标丈量仪（三次元）—Coordinate Measure Machine（CMM）6．塞规— pin gauge7．圆角量规—radii gauge8．轮廓投影机— profile projectorJ．注塑机参数 Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧种类 clamp typea．油缸— hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小 /最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小 /最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力— clamping force⑨顶出行程—ejector stroke⑩顶卖力— ejector force2．试模工艺参数 Moulding Process Parameter, machine setting①时间 Timer （TM）, seca．注塑（充填）时间—filling time, injection timeb．冷却时间—cooling timec．补缩时间—packing timed．保压时间—holding timee．成型周期—cycle time②速率、速度 Velocity, %、speed, in/sec③ 压力④ 温度a．注塑（充填）速度—injection speedb．保压速率—hold pressure velocityc．螺杆转速—screw rotation speedPressure （Prs. ）, psia．注塑压力—injection pressureb．保压压力—hold pressurec．回压（背压）—back pressureTemperature （Temp.）,° Fa．注塑机喷嘴温度—nozzle temp.b．料筒前段、中段、后段温度—barrel frontc．模温—mould temp.、 middle 、rear temp. d．料温—purged resin melt temp.e．空射料温—air shot melt temp.。
模具专业英语词汇
模具专业英语词汇摘要：模具是一种用于生产特定形状的产品的工具，它在制造业中有着广泛的应用。
模具专业英语词汇是指与模具相关的专业术语，它涉及到模具的设计、制造、检验、使用等方面。
本文根据不同的主题，整理了一些常用的模具专业英语词汇，并用表格的形式进行了展示，以便于读者学习和参考。
1. 模具类型模具是一种用于生产特定形状的产品的工具，它可以分为不同的类型，根据加工方法和材料的不同，可以分为以下几类：中文英文注塑模injection mold压铸模die-casting mold冲压模stamping mold挤出模extrusion mold吹塑模blow mold硅胶模silicone mold砂型模sand mold石膏模plaster mold三板模three-plate mold双色模two-color mold2. 模具结构模具结构是指模具的组成部分和连接方式，它决定了模具的功能和性能。
一般来说，一个完整的模具由以下几个部分组成：中文英文模架mold base模芯core模腔cavity浇口系统gate system导向系统guiding system顶出系统ejection system冷却系统cooling system3. 模架模架是指支撑和固定模芯、模腔等部件的基础结构，它通常由标准件或定制件组成。
常见的模架部件有：中文英文定模座板fixed clamping plate动模座板moving clamping plate定模套板fixed bolster plate动模套板moving bolster plate支承板backing plate垫块spacer block4. 模芯和模腔模芯和模腔是指与被加工材料直接接触并形成产品形状的部件，它们通常由钢材或其他硬质材料制成。
常见的与模芯和模腔相关的术语有：中文英文凹面（内型面）concave surface (inner surface)凸面（外型面）convex surface (outer surface)分型面（合型面）parting surface (matching surface)型芯固定板（凸模固定板）core-retainer plate (punch-retainer plate)凹模固定板（凸模固定板）cavity-retainer plate (die-retainer plate)5. 浇口系统浇口系统是指将熔融或液态材料从注塑机或压铸机输送到型腔中的通道，它包括浇口、流道、冷料井等部件。
模具,冲压相关英语专业翻译
模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形6vaggh - 2007-01-15 10:58encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ?泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模7vaggh - 2007-01-15 10:58各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具8vaggh - 2007-01-15 10:58double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具9vaggh - 2007-01-15 10:59segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模10vaggh - 2007-01-15 10:59模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口11vaggh - 2007-01-15 10:59die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板12vaggh - 2007-01-15 10:59fixed bolster plate 固定侧模板 flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶?lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板 moving bols13vaggh - 2007-01-15 11:00parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导?pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 托料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料? 14vaggh - 2007-01-15 11:00spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 托板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键taper pin 拔锥梢/锥形梢 teeming 浇注three start screw 三条螺纹 thrust pin 推力销tie bar 拉杵 tunnel gate 隧道形浇口vent 通气孔 wortle plate 拉丝模板。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具工程常用词汇
模具工程是现代制造工业中的重要领域，模具的使用涉及到许多专业术语。
在此，我们将会介绍一些模具工程中的常用词汇，其中包括常见的工艺、材质、及其相关参数等等，以期使读者能够更好地理解模具工程中的相关知识。
一、常用工艺
1.数控加工：数控加工是利用计算机进行机械加工的现代
化加工方式。
模具工程中利用数控加工的优点在于，它可以大大提高加工精度和效率。
2. 电火花加工：电火花加工是一种模具加工的特殊技术，其利用高压放电的原理来切割材料。
相对于传统的机械加工方式，电火花加工可以切割出更为精细的零件。
3.玻璃钢制造：玻璃钢制造是利用玻璃纤维增强塑料与树
脂混合物制作模具的一种工艺。
玻璃钢强度高、重量轻，并且可以进行复杂的成型，成为现代模具工程中常用的材料。
4.模组技术：模组技术是指将模具分成几个部件，轻便地
组装和拆卸，实现了高效生产的制造方法。
二、常用材质
1.钢材：钢材是一种具有定形、可塑性、高强度、耐腐蚀
性等特点的金属材料，是模具制造中最常用的材料之一。
钢材的种类很多，根据不同的用途选择不同的钢材种类，亦能看出
生产电子、汽车等行业使用的模具需要的淬火性、韧性、耐磨性等物理特性的不同。
2.铝合金：铝合金具有低密度、良好的导电性、高强度等
特点。
在模具制造中，铝合金材质更常被用于制造小型零件的模具，如透镜组件、薄壳产品等等。
3.铜材：铜材具有良好的热导性以及易加工性。
在模具工
程中，铜材通常被用于制造电子零件的模具，如晶体管、电容器等等。
4.塑料：塑料是一种与电子工业紧密相关的材料，它可以
使得模具的表面更光滑、更光亮。
在模具工程中，塑料通常被用于制造高精度材料的零件，如齿轮、紫外线透镜组件等等。
三、常用参数
1. 高度：在模具成型过程中，高度是一个重要的参数。
高度的长度和大小直接影响到产品的成型结果和质量。
2. 厚度：厚度与高度一样，是模具加工中一个重要的参数。
厚度的大小和材料种类有关，钢材多用于配制较厚薄的模具，铝合金、铜材多用于小件或者轻型的模具。
3.精度：精度是模具制造的关键指标之一，它可以表示成
型模具的成型品质。
模具加工精度主要有形位公差和尺寸精度。
为了减少加工误差，需要保证加工设备的精度和检验设备的精度。
4. 物理特性：钢材、铝合金、铜材等材质中的物理特性
是模具成型的最基本的参数。
例如，在制造大型模具时，钢材
具有更好的刚性和强度，比铝合金焊接性要好；而铝制品则可以修正加法精度以提高精度。
总结
综上所述，模具工程中的常用词汇涉及到许多方面，从工艺到材质、再到参数等，都在模具生产的各个环节起到至关重要的作用。
模具的材质种类多样，从钢材到铝合金、从铜制品到塑料，每种材质都有其独特的特点和优势，而模具的精度、高度和厚度等参数更是直接影响模具生产的成效和品质。
因此，在进行模具生产时，应该选择适合自己的材料和精度参数，并在制造过程中时刻关注这些关键指标的变化，以达到最好的成型效果和生产效率。