常见不良中英文对照
SMT焊接不良现象中英文对照表
[replyview]不良现象中英文对照表1.缺件(MISSING PARTS) 28.脚未弯(PIN NOT BENT) 55.印章错误(WRONGSTAMPS)2.错件(WRONG PARTS) 29.缺盖章(MISSING STAMP) 56.尺寸错误(DIMENSION WRONG)3.多件(EXCESSIVE PARTS) 30.缺卷标(MISSING LABEL) 57.二极管坏(DIODE NG)4.短路(SHORT) 31.缺序号(MISSING S/N) 58.晶体管坏(TRANSISTOR NG)5.断路(OPEN) 32.序号错(WRONG S/N) 59.振荡器坏(X’TL NG)6.线短(WIRE SHORT) 33.卷标错(WRONG LABEL) 60.管装错误(TUBESWRONG)7.线长(WIRE LONG) 34.标示错(WRONG MARK) 61.阻值错误(IMPEDANCEWRONG)8.拐线(WIRE POOR DDRESS) 35.脚太短(PIN SHORT) 62.版本错误(REVWRONG)9.冷焊(COLD SOLDER) 36.J1不洁(J1 DIRTY) 63.电测不良(TEST FAILURE)10.包焊(EXCESS SOLDER) 37.锡凹陷(SOLDER SCOOPED) 64.版本未标(NONREV LEBEL)11.空焊(MISSING SOLDER) 38.线序错(W/L OF WIRE) 65.包装损坏(PACKING DAMAGED)12.锡尖(SOLDER ICICLE) 39.未测试(NO TEST) 66.印章模糊(STAMPSDEFECTIVE)13.锡渣(SOLDER SPLASH) 40.VR变形(VR DEFORMED) 67.卷标歪斜(LABELTILT)14.锡裂(SODER CRACK) 41.PCB翘皮(PCB PEELING) 68.外箱损坏(CARTONDAMAGED)15.锡洞(PIN HOLE) 42.PCB弯曲(PCB TWIST) 69.点胶不良(POOR GLUE)16.锡球(SOLDER BALL) 43.零件沾胶(GLUE ON PARTS) 70.IC座氧化(SOCKET RUST)17.锡桥(SOLDER BRIDGE) 44.零件脚长(PARTS PIN LONG) 71.缺UL卷标(MISSING UL LABEL)18.滑牙(SCREW LOOSE) 45.浮件(PARTS LIFT) 72.线材不良(WIRE FAILURE)19.氧化(RUST) 46.零件歪斜(PARTS TILT) 73.零件脚损坏(PIN DAMAGED)20.异物(FOREIGNER MATERIAL) 47.零件相触(PARTS TOUCH) 74.金手指沾锡(SOLDER ON GOLDEN FINGERS)21.溢胶(EXCESSIVE GLUE) 48.零件变形(PARTS DEFORMED) 75.包装文件错(RACKING DOC WRONG)22.锡短路(SOLDER BRIDGE) 49.零件损坏(PARTS DAMAGED) 76.包装数量错(PACKING Q’TY WRONG)23.锡不足(SOLDER INSUFFICIENT) 50.零件脚脏(PIN DIRTY) 77.零件未定位(PARTS UNSEATED)24.极性反(WRONG POLARITY) 51.零件多装(PARTS EXCESS) 78.金手指沾胶(GLUE ON GOLDEN FINGERS)25.脚未入(PIN UNSEATED) 52.零件沾锡(SOLDER ON PARTS) 79.垫片安装不良(WASHER UNSEATED)26.脚未出(PIN UNVISIBLE) 53.零件偏移(PARTS SHIFT) 80.线材安装不良(WIRE UNSEATED)27.脚未剪(PIN NO CUT) 54.包装错误(WRONG PACKING) 81. 立碑(TOMBSTONE)。
各种不良的中英文对照表
Visiable line at material joint area due to release of internal stress. Gloss different due to internal stress releasing after painting at gate area, weld line, etc.
Remark
Remark
Rg Code Name Defect Name 201 Color Different/色差 202 Gloss Different/光泽差 Matting/麻点 203 Orange peel/橘皮 204 205 Runs/挂流 206 Miss Painting/漏喷 207 Over Painting/过喷 208 Air Bubble/气泡 Impurity/杂质 209 210 Scratch/划伤 Shiny Mark/亮斑 211
Defect Description A moderate depression on the surface of a part. The part is bent, twisted. Excess material not supposed to be on the part. Injection of the part is not complete. Line of joining of material Colour tone differences by the injection point. Colour tone differences in the surface. Blackened and burnt areas Colour tone stripes or dots in the surface Abrasion, groove on the surface. deviations appearing as shiny areas from the defined roughness of the surface. Air bubble on the surface Color deviation from target color Deviation from defined surface texture. Visible particles in or on the surface such as black dot, white dot, dust, grease, etc. Bump on the surface due to ejecting the part. A recess on the surface Ink was washed on the printing Caused by label is bigger than cavity Caused by label is smaller than cavity Handling Issue Logo, artwork position deviation Damage due to handling, transportation or packaging. The transparency on lens is not good. Missing material step due to slide not at the same level.
产品不良名称中英文对照
PC膜 不良
少切 Under cut 过切 Over Cut 剥离 Delamination 波纹 Wrinkle 压伤 Breaking 原物料不良 Material NG
刮伤 Scratch 透光 Dead Color, Transparency 黑点 Black Dot 起苍 Silver Streak 剥离 Delamination 冲墨 Wash out IMD冲膜 Wash out 缩水 Shrinkage 变形 Transfingeration / Deform 缺料 Void 折痕 Silver Break 脏污 Dirty / Contamination 偏位 Offset 凹点 Dented / Concave
Dirty / Contamination Scratch Distressed / Breaking Dented / Concave Convex Offset Deform Void Silver Break Split Abrade,grind
透光 Dead Color, Transparency
不良项中英文对照
制程
不良项
刮伤 Scratch 手痕 Finger Print
毛屑 Fiber
印刷点 Printing Dot
透光 Dead Color, Transparency
偏位 Biased, Offset
锯齿 Saw, Zigzag
色差 Discoloration
气泡 Bubble
折痕 Silver Break
模 Sticking 过火 BOuvrenr Size / Dimension out of 尺寸不符 spec. 压伤 Breaking 刮伤 Scratch 透光 Dead Color，Transparency 偏位 Deform 脏污 Dirty/Contamination 残胶 Adhensive Out/Glue Residual 溢胶 Glue Smear/Over Glue
不良中英文对照表
PU表面略刮伤 Slight scratch on PU surfacePU下面的泡棉不平 Foam is uneven包装漏放五金包 Missing Hardware Kit爆钉穿破PVC特别刮手 Explored staple piercing PVC and it is easy to scratch hand背侧PVC拉太紧起皱 PVC of side of back cushion is too tight背垫PVC刮伤 Scratches on PVC of back cushion背垫PVC略刮伤 Slight scratch on PVC of back cushion背垫PVC破损 PVC of back cushion torn背垫背封车缝未车牢 Broken stitching on back cover背垫背封浮钉 Float staple on back cover背垫背封破损 Back cover torn背垫背钢板孔距与底盘孔距不吻合,螺丝无法组立 Assembly can't be done due to the distance of holes on back bar and seat plate is different背垫边条管处露底线 The inner thread which is located welting strip of back cushion coming out 背垫边条管略刮伤 Slight scratch on welting strip of back cushion背垫边条管外翻 Welting strip of back cushion protruding outward背垫边条管压伤 Indentation on welting strip of back cushion背垫表面有一死皱 Wrinkle on back cushion occurred by defective stitching背垫表面皱大 Much wrinkles on back cushion背垫表面皱大,腰靠太平 Wrinkles on back cushion and lumber is too flat背垫布料刮伤 Fabric of back cushion is scratched背垫布料破 Fabric of back cushion torn背垫侧包压皱 Indentation on side of back cushion背垫侧边管条弯曲 Welting strip of back cushion is crooked背垫侧边皱折 Wrinkles on back cushion背垫车缝开线 Broken stitching on back cushion背垫车缝松线 Loose stitching on back cushion背垫车缝跳针 Skip stitching on back cushion背垫吊卡有折痕 Folds on the hangtag of back cushion背垫缝套二层皮有皮疤 Scar on leather of back cover背垫扶手孔位漏烙孔 Hole on back cushion for assembling arm is missing背垫扶手孔无丝牙 Hole for assembling arm on back cushion has no thread背垫管条刮伤 Scratch on welting strip of back cushion背垫管条弯曲 Welting strip of back cushion is crooked背垫肩部凹陷 Indentation on shoulder of back cushion背垫肩部厚度不够 Thickness of shoulder of back cushion is not enough背垫肩部内缩 Shoulder of back cushion shrinking to the inner背垫肩侧空，皱 Side of back cushion is empty and wrinkled背垫胶袋用错（本应为三国语言，错用为七国语言的胶袋）Plastic bag of back cushion is wrong, it should be three kind of language on bag, but there is seven kind of language on bag 背垫拉点太浅 Pulling strength isn't enough背垫拉扣太松,易拔出 Button on back cushion is too loose and easy to pull out背垫拉链开裂 Zipper on back cushion broken背垫漏烙孔 Missing hole on back cushion背垫露棉 Foam inside of back cushion exposed背垫略刮伤 Slight scratch on back cushion背垫略歪斜 Back cushion is slight crooked背垫略有针孔露白 Pinholes on back cushion revealing white背垫略有皱折 Slight wrinkle on back cushion背垫螺丝孔被套子堵住 Screw hole on back cushion is jammed背垫面料上粉笔印未清洁干净 Chalk marking on fabric of back cushion背垫内外板线条对不上 Two stitching lines of back cushion aren't aligned背垫皮吊卡烫金字体模糊 The golden letters of hangtag on seat cushion are not clear背垫皮料腐皮 Leather of back cushion is decayed背垫皮料刮伤 Scratches on leather of back cushion背垫枪钉外露 Staple on back cushion exposed背垫清洁不良 Poor cleanness on back cushion背垫清洁不良(灰尘) Poor cleanness on back cushion (Dust)背垫清洁不良(水银笔印) Poor cleanness on back cushion (Silver pen mark)背垫上粘有贴纸 Tape sticking on back cushion背垫松线 Loose stitching on back cushion背垫头部凹凸不平 Headrest of seat cushion is uneven背垫头部空 Headrest of back cushion is flat背垫头枕略有皱折 Slight wrinkle on headrest of back cushion背垫头枕内外板缝隙处PVC外露 PVC which is located the headrest of back cushion exposed 背垫歪斜 Back cushion is crooked背垫歪斜较严重 Back cushion is crooked seriously背垫线头 Untrimmed thread on back cushion背垫严重碰破 Back cushion broken背垫针孔过大 Obvious pinholes on back cushion背垫皱折 Wrinkles on back cushion背封PVC刮伤 Scratches on PVC of back cover背封PVC破 PVC of back cover torn背封边条管弯曲 Welting strip of back cover is crooked背封处断钉 Broken staple on back cover背封封钉未封不牢 Staple for fastening back cover is not fast背封浮钉刮手 Float staple on back cover背封刮破 Back cover broken背封刮伤 Back cover is scratched背封漏封钉 Missing staple on back cover背封露棉 Foam inside of back cover exposed背封清洁不良 Poor cleanness on back cover背封压伤 Indentation on back cover背封有压痕 Indentation on back cover背封皱折 Wrinkles on back cover背钢板处PVC压皱 Indentation on PVC beside the back bar背钢板掉漆生锈 Back bar is rusty背钢板套子PVC破损 PVC of cover for back bar torn背钢板套子皱折 Wrinkles on cover of back bar背弯管略掉漆 Metal frame is scratched背下露PVC PVC which is located underside of back cushion exposed背下露木板露 Plywood of back cushion exposed本应用CP143N五爪；混用:CP144-26五爪 Base is misapplied, it should be CP-143N, but CP-144N-26 is used标签位置不对 Label is adhered improperly标签字体模糊 Letter of label is not clear布料表面有线结 Thread kink on fabric布料上有杂色线 Mottle on fabric车缝线外露 Stitching thread exposed车缝压线宽窄不一致 Width of two stitching lines is different成品箱内漏放左手铁架 Missing left metal arm frame from box冲孔皮皮层纤维外露 Fiber inside of punching leather exposed底盘把柄布套车缝松线 Loose stitching on fabric cover of handle of seat plate底盘把柄顶到扶手铁无法升降 The handle of seat plate touching the bracket resulted in the lift and drop can't be done底盘把柄皮套粘贴不牢 Leather cover for handle of seat plate is not fast底盘把手上有胶水 Glue on handle of seat plate底盘表面磨伤 Scratches on seat plate底盘胶袋上有水 Glue on plastic bag for packing seat plate底盘上有油渍 Stain on the seat plate垫子无防布烫破 Fabric on cushion burned out二节杯上毛边 Burrs on the 2 tier cup防尘套破 Telescoping cover broken仿皮皮文较浅，且发亮 Grain on PVC is too flat and light扶手边管条未打紧 Welting strip of arm pad is not fast扶手边条管刮伤 Welting strip of arm is scratched扶手边条管内缩 Welting strip of arm shrinking to the inner扶手边条压线不对称 Two stitching lines of arm pad aren't aligned扶手车缝线错位 Two stitching lines of arm pad aren't aligned扶手底布未打好 Fabric which is loacted bottom of arm pad is not fast扶手底布有粉笔痕迹 Chalk marking on fabric of arm扶手垫边条管略刮伤 Slight scratch on the welting strip扶手垫边条管略外露 Welting strip of arm pad exposed扶手垫边条管内缩 Welting strip of arm pad shrinking to the inner扶手垫车缝松线 Loose stitching on arm pad扶手垫车缝线接口不牢(易拔出) Stitching joint on arm pad is not fast扶手垫底部有粉笔痕迹 Chalk marking on bottom of arm pad扶手垫刮伤 Arm pad is scratched扶手垫略有针孔露白 Pinholes on arm pad revealing white扶手垫略有皱折 Slight wrinkle on arm pad扶手垫面料有暗疤 Scar on fabric of arm pad扶手垫明线不顺畅且打的凹凸不平 Stitching line on arm pad is not smooth 扶手垫前端略皱折 Slight wrinkle on the front of arm pad扶手垫轻微皱折 Slight wrinkle on arm pad扶手垫清洁不良 Poor cleanness on arm pad扶手垫清洁不良(灰尘) Poor cleanness on arm pad (Dust)扶手垫清洁不良(水银笔印) Poor cleanness on arm pad (Silver pen mark)扶手垫跳线 Skip stitching on arm pad扶手垫头部皱折 Wrinkles on front of arm pad扶手垫下不织布外露 Non-woven fabric on arm pad exposed扶手垫线头 Untrimmed thread on arm pad扶手垫压线跳线 Skip stitching on arm pad扶手垫皱折 Wrinkles on arm pad扶手刮伤 Arm is scratched扶手管条接头处缝隙大 Space on welting strip of arm pad扶手厚薄不一致 Thickness of arm pad is inconsistent扶手架表面刮伤 Arm is scratched扶手架表面较粗糙 Surface of arm is not smooth扶手架表面气泡袋印 Bubble bag marking on the surface of arm扶手架表面汽泡 Bubble on the arm (Coating for arm is defective)扶手架车缝松线 Loose stitching on arm support扶手架掉漆 Arm is scratched扶手架刮伤 Arm is scratched扶手架灰尘 Dust on the arm扶手架烤漆不良 Coating for arm support is defective扶手架略有掉漆 Slight scratch on arm support扶手架毛边(略刮手) Burrs on arm (Scratch hand)扶手架毛边(未打磨平) Burrs on the arm due to the arm didn't be polished扶手架磨伤 Arm is scratched扶手架清洁不良 Poor cleanness on arm扶手架清洁不良(EVA粘在扶手架上) Poor cleanness on arm (EVA sticking on arm)扶手架清洁不良(灰尘) Poor cleanness on arm support (Dust)扶手架上向前标贴的不规范 Location of FRONT label on arm is not correct扶手架上有污渍未清洁干净 Smut on arm pad扶手架脱漆 Arm is scratched扶手架与背垫间隙太大 Distance between arm and back cushion is too big扶手螺丝头毛刺严重刺手 Strictly burrs on screw of arm扶手轻微刮伤 Slight scratch on arm扶手铁片灰尘 Dust on the metal bracket of arm扶手同边 Two arms are the same side扶手线头 Untrimmed thread on arm扶手压变形 Arm pad distorted扶手左右标贴错 L or R label on arm is wrong胶垫易破 Plastic washer is easy to break角铁孔烙太大 Hole on bracket is too big角铁孔上棉屑 Foam on the hole of arm bracket漏贴西班牙文向前标 Missing Spanish FRONT label轮子有白色斑点 White stain on caster面料上有折痕 Folds on fabric能摸到扶手组装螺丝 Screw for assembling the arm pad can be felt能摸到铁条 Metal line in the back cushion can be felt能直接摸到木板棱角 Plywood corner can be touched汽压棒外管生锈 Canister of gas lift is rusty枪钉堵孔 Hole is jammed with staples三节杯上有灰尘 Dust on 3-tier-cap手工太差 Poor handcraft手工太差,有海棉棱角 Poor handcraft, foam corner铁架刮伤 Metal frame scratched铁架横杆变形(不能组立) Assembly can't be done due to the crossing pole distorted铁架胶垫晃动(螺丝未上紧) Plastic washer of metal frame is wobbly as the screw is not fast铁架胶塞未塞到位 Plastic cap of metal frame filled improperly铁架孔位与座底孔位不对无法组装 Assembly can't be done due to the holes on metal frame and seat cushion are not matched铁架略刮伤 Metal frame is scratched铁五爪插销孔内有焊渣，轮子差不进去 Hole of meat base is jammed with solder resulted in caster can't insert五爪掉漆 Base is scratched五爪盖脱落 Cap of base falling off五爪刮伤 Base is scratched五爪胶盖上有灰尘 Dust on plastic caps of base五爪脚盖破 Caps of base broken五爪清洁不良 Poor cleanness on base五爪清洁不良(有灰尘) Poor cleanness on base (Dust)五爪生锈 Rusty base线头 Untrimmed thread纸箱SKU#错误 SKU# on carton is wrong纸箱唛头错误 Shipping mark on carton is wrong坐垫皮料破 Leather of seat cushion torn座背垫侧边缝隙 Gap between side of seat and back cushion座背垫间隙 Gap between seat and back cushion座背垫线条不对称 Two stitching lines of seat and back cushion aren't aligned座背垫组立后略有缝隙 Space between seat and back cushion座底标签破损 Label on bottom of seat cushion torn座底不织布破损 Non-woven fabric on seat cushion torn座底钉距太稀 The distance of staples is too big座底扶手螺丝孔位漏烙 Missing hole on bottom of seat cushion for assembling arm 座垫PVC刮伤 Scratches on PVC of seat cushion座垫PVC略刮伤 Slight scratch on PVC of seat cushion座垫PVC破损 PVC of seat cushion torn座垫边条管角易拨出 End of welting strip of seat cushion is easy to pull out座垫边条管略刮伤 Slight scratch on welting strip of seat cushion座垫边条管弯曲 Welting strip of seat cushion is crooked座垫布料破碎 Fabric of seat cushion torn座垫侧边凹凸不平 Side of seat cushion is uneven座垫侧边空 Side of seat cushion is flat座垫侧边皱折 Wrinkles on side of seat cushion座垫车缝松线 Loose stitching on seat cushion座垫车缝跳针 Skip stitching on seat cushion座垫底盘组立困难 It is difficult to assemble seat plate and seat cushion座垫浮钉 Float staple on seat cushion座垫浮钉刮手 Float staple on seat cushion and it is easy to scratch hand座垫华司灰尘过多 Much dust on plastic washer of seat cushion座垫拉点太浅 Pulling strength for seat cushion isn't enough座垫漏放电话卡 Missing toll-card座垫漏烙底盘孔 Missing hole on seat cushion for assembling seat plate座垫略刮伤 Slight scratch on seat cushion座垫略有浮钉 Float staple on seat cushion座垫略有皱折 Slight wrinkle on seat cushion座垫螺丝孔处拉线未清理干净 Pulling wire which is loacted the hole on seat cushion is remnant 座垫内缩 Seat cushion shrinking to the inner座垫皮料磨伤 Leather of seat cushion is scratched座垫皮料破 Leather on seat cushion torn座垫清洁不良 Poor cleanness on seat cushion座垫清洁不良(木屑) Poor cleanness on seat cushion (Wood scraps)座垫清洁不良(水银笔印) Poor cleanness on seat cushion (Silver pen mark)座垫松线 Loose stitching on seat cushion座垫头部压皱 Wrinkles on the front of seat cushion座垫头枕边条管弯曲 Welting strip of seat cushion is crooked座垫线头 Untrimmed thread on seat cushion座垫压皱 Indentation on seat cushion座垫有轻微针孔露白现象 Pinholes on seat cushion revealing white座垫皱折 Wrinkles on seat cushion座前凹凸不平 Front of seat cushion is uneven座中两侧手工不对称 Two sides of seat cushion aren't aligned手工太差,有海棉棱角Poor handcraft, foam corner标签位置不对 Label is adhered improperly能摸到扶手组装螺丝Screw for assembling the arm pad can be felt底盘上有油渍Stain on the seat plate皮面疤痕Scar on leather on back cushion五爪胶盖没有装好Cap of base is apart皮/布下面的泡棉不平 uneven foam under the leather /fabric二节杯上毛边 burrs on the 2 tier cup扶手厚薄不一致 Thickness of arm pad is different背垫上粘有贴纸 Tape sticks on back cushion座底标贴不规范 label on seat cushion doesn't adhere properly座底不织布外露 non woven exposed under the seat cushion铁管架脚垫脏污 poor clean on plastic pads of metal frame扶手角铁螺母没有露在外面 nut on arm bracket of back cushion doesnot outside exposed铁架管塞没塞好 plastic cap on the top of metal frame doesn't stopper三节杯杯口太大,自由坠落 center hole of telescoping cover is too big,cover can't be done to the gas lift角铁孔上棉屑 foam on the hole of arm bracket能摸到铁条 metal line in the back cushion can be felt枪钉堵孔 staple plug up the hole of nut座底钉距太稀 Staple on seat cushion is very sparse座垫树脂棉外露 Colophony foam inside of seat cushion exposed椅脚颜色错误 Color of base is not correct扶手架损坏 Defective hole on arm背钢板套没有装好 Cover border of back bar exposed背封边条接头没接好 Joint on welting strip of back cover is not acceptable背后"serta"LOGO 没有放正 "serta" logo on back cushion is reverse底盘把柄没有装好 Handle of seat plate is loose底盘把柄装反 Handle of seat plate is reverse座底不织布烙坏 Non-woven fabric on bottom of seat cushion torn by welding背钢板表面粗糙 Bac bar is rough背封内枪钉未打平 Staple inside of back cover can be felt扶手垫上凹槽 Dent on arm pad车缝子口宽窄不一致 Defective stitching on back cushion底盘锥孔太大,组装后椅子自动升降 Hole on seat plate is too big resulting the chair fall down automatically车缝线接头没有叠在一起 Defective stitching on cushion背侧内缩 Side of back cushion shrinking to the inner目的地错误,与订单不符 Destination on carton is not correct座底不织布下泡棉未修饰 Foam exposed扶手装饰条没装好 Welting strip of arm pad is not acceptable扶手垫下边条枪钉没打牢 Staples for fastening the arm pad are loose皮面纹路不一致 Embossing of leather is not matched铁架横杆生锈 Crossing pole is rust座底枪钉盖住标签字体 Staples covering the letter on label缺少一个拉链头 Zipper has not handle漏组螺丝 Missing screw螺丝没有锁紧 Screw is not locked tight扶手装饰条没装好 Welting strip of arm pad is not acceptable座底不织布太薄 Non-woven fabric is too thin扶手边条管接头处没包好 Joint of welting line of arm pad is not packed well多放保证卡 This item no need guarantee card, but guarantee card is put in the carton 背垫内外板开裂 The inner and outer plywood of back cushion is apart扶手前端组装略有缝隙 Space between arm pad and support扶手垫装反 Arm pad is assembled in reverse布料断纱 Broken yarn纸箱压变形 Carton distorted车缝线没有重合在一起 Defective stitching on cushions背角铁上锁针生锈 locking pin of arm bracket is rust扶手架前端边缘外露 Arm pad can't cover totally the arm support冲孔皮面绒毛 Floss on the punching leather公英制螺丝五金包混用 Screws with Metric system and British & U.S. system mixed 背钢板套发霉 Moldy on back cover扶手孔变形堵塞无法组装 Hole on arm is distorted扶手孔铁片颜色不一致 The color of metal slips on arm is different三节杯杯口形状不一致 The tape of 3-tier-caps is different扶手架表面水印 Watermark on arm support扶手表面处理颜色不一致 Coating for arm is defective说明书错用为旧版 Assembly instruction is not correct座垫露丝棉 Silk foam exposed扶手孔边缘未修饰 Burrs on hole of arm扶手装饰条装好后有缝隙 Space between the inserts and arm support能摸到铁条 Metal rod can be felt扶手上小孔大小不一致 Hole on arm is defective 座垫露丝棉 Silk foam exposed拉点深浅不一致 Pulling strength is different。
常见不良缺陷翻译
下面列出一些常用的不合格项目的英文翻译，供参考：线头- Thread end线头未剪- Untrimmed thread end色差- Color difference印刷不良-Poor printing车缝不良- Poor sewing覆膜不良- Poor coating折痕- Crease起皱- Goffer批锋、毛边、毛刺- 五金：Burr，塑胶： Flash 做工不良- Poor workmanship破裂，开裂、破损 - Broken裂缝，裂纹、裂口– Rip缝合处爆开- Seam broken车缝爆开- Sewing broken车线断– Stitch broken抽丝（抽纱）- Poor material (不完全对应)拉毛、起毛– Napping松动- Loose脏污- Dirt油污– Oil mark流水痕(纹) - Flow mark灰尘- Dust刮伤、刮花- Scratch凹坑、凹陷- Dent缩水- shrinkage变形- Deformation退色- discolor发霉- Mould喷涂不良- Poor painting电镀不良- Poor plating杂质- Impurity尖点（铁刺）- Sharp point利边- Sharp edge扭曲- Contortion弯曲、扭曲、翘曲- Curl切割不良– Poor cutting（五金）冲压不良– Poor punch生锈– Rust根据PO和sample验货— Did inspection per PO and the sample.大货和样品基本一致—The product basically same as sample.品质符合SIC要求-- The quality meet SIC.箱唛和包装见图片-- Shipping marks and package see photoes.资料不全、不齐-- The inspection informations not complete.无签样- No approved sample.通过-- Pass失败、不通过-- Failed另外：常用单词外箱- Carton, 内箱（内盒）- Inner box, 彩盒- Color box, 邮购盒- Remailer box唛头- Mark尺寸- Dimension大小- Size重量- Weight长- Length，宽- Width，高- Height, 厚度- Thickness组装（装配）- Assembly配件- Accessory外形- Shape，结构- Structure，连接头（器）- Connector湿度- Humidity，湿度计– Hygrometer，温度计– Thermometer，卷尺- Tapeline，卡尺- Callipers，金属探测仪– Metal detector, 缝纫机– Sartorius冲床– Punch，车床– Lathe，模具– Mold (tooling), 修改模具- Modify mold, 试模– Off tool, 试产– Pilot run电器产品：高压测试- Hi-pot test, 泄漏电流- Current leakage，接地电阻- Earth continuity 电火花- Spark，短路- Short circuit, 断路- Open circuit验货报告中的英文说明：Package包装1. Master carton markings:外箱箱唛2. Inner carton markings:内盒箱唛3. Country of origin:原产地4. Specail requirements on CTN:外箱上的特殊要求5. Master CTN Qty:外箱里的数量6. Inner CTN Qty:内盒里的数量7. Barcode / Upc / Other label 条形码、UPC、其他LABEL8. Words / graphic correct 文字、图案正确否（特殊的）9. Poly bag / warnings:塑胶袋、警告字句Function / Material功能、材料1. Appearance:外观2. Color:颜色3. Shape and demension of product:外形、尺寸4. Assembly test:装配测试5. Material:材料6. Accessories:配件7. Compare with file / approved samples / photo:和文件、签样、相片对照的结果8. Test as user manual / MI:按用户说明手册测试9. Function performance:功能测试的性能是否符合要求Other其他1. No sharp point / edge无尖点、利边2. Safety pull / push test:拉力、推力测试3. Reliability test可靠性测试4. Electrical test: Hi-pot / Polarity / earth电气性能测试：高压测试、电线极性测试、接地电阻测试5. Lab test / Brine test实验室测试、盐水测试6. Abuse test 破坏性测试7. Other test 其他测试8. Ctn size: X X 外箱尺寸，后面填写单位9. NW: 净重，后面填写单位GW:毛重，后面填写单位。
不良中英文对照表
不良现象中英文对照表1.缺件(missing parts)2.错件(wrong parts)3.多件(excessive parts)4.短路(short)5.断路(open)6.线短(wire short)7.线长(wire long)8.拐线(wire poor ddress)9.冷焊(cold solder)10.包焊(excess solder)11.空焊(missing solder)12.锡尖(solder icicle)13.锡渣(solder splash)14.锡裂(soder crack)15.锡洞(pin hole)16.锡球(solder ball)17.锡桥(solder bridge)18.滑牙(screw loose)19.氧化(rust)20.异物(foreigner material)21.溢胶(excessive glue)22.锡短路(solder bridge)23.锡不足(solder insufficient)24.极性反(wrong polarity)25.脚未入(pin unseated)26.脚未出(pin unvisible)27.脚未剪(pin no cut)28.脚未弯(pin not bent)29.缺盖章(missing stamp)30.缺标签(missing label)31.缺序号(missing s/n)32.序号错(wrong s/n)33.标签错(wrong label)34.标示错(wrong mark)35.脚太短(pin short)36.j1不洁(j1 dirty)37.锡凹陷(solder scooped)38.线序错(w/l of wire)39.未测试(no test) 40.vr变形(vr deformed)43.零件沾胶(glue on parts)41.pcb翘皮(pcb peeling)42.pcb弯曲(pcb twist)44.零件脚长(parts pin long)45.浮件(parts lift)46.零件歪斜(parts tilt)47.零件相触(parts touch)48.零件变形(parts deformed)49.零件损坏(parts damaged)50.零件脚脏(pin dirty)51.零件多装(parts excess)52.零件沾锡(solder on parts)53.零件偏移(parts shift)54.包装错误(wrong packing)55.印章错误(wrong stamps)56.尺寸错误(dimension wrong)57.二极管坏(diode ng)58.晶体管坏(transistor ng)59.振荡器坏(x’tl ng)60.管装错误(tubes wrong)61.阻值错误(impedance wrong)62.版本错误(rev wrong)63.电测不良(test failure)64.版本未标(non rev lebel)65.包装损坏(packing damaged)66.印章模糊(stamps defective)67.标签歪斜(label tilt)68.外箱损坏(carton damaged)69.点胶不良(poor glue)70.ic座氧化(socket rust)71.缺ul标签(missing ul label)72.线材不良(wire failure)73.零件脚损坏(pin damaged)74.金手指沾锡(solder on golden fingers)75.包装文件错(racking doc wrong)76.包装数量错(packing q’ty wrong)77.零件未定位(parts unseated)78.金手指沾胶(glue on golden fingers)79.垫片安装不良(washer unseated)80.线材安装不良(wire unseated)81.立碑(tombstone)。
SMT常见不良中英文对照
SMT常见不良中英文对照1.缺件(MISSING PARTS)2.错件(WRONG PARTS)3.多件(EXCESSIVE PARTS)4.短路(SHORT)5.断路(OPEN)6.线短(WIRE SHORT)7.线长(WIRE LONG)8.拐线(WIREPOORDDRESS)9.冷焊(COLD SOLDER)10.包焊(EXCESSSOLDER)11.空焊(MISSING SOLDER)12.锡尖(SOLDER ICICLE)13.锡渣(SOLDER SPLASH)14.锡裂(SODER CRACK)15.锡洞(PINHOLE)16.锡球(SOLDER BALL)17.锡桥(SOLDER BRIDGE)18.滑牙(SCREWLOOSE)19.氧化(RUST)20.异物(FOREIGNER MATERIAL)21.溢胶(EXCESSIVEGLUE)22.锡短路(SOLDER BRIDGE)24.极性反(WRONG POLARITY)25.脚未入(PINUNSEATED)27.脚未剪(PINNOCUT)28脚未弯(PINNOTBENT)29.缺盖章(MISSINGSTAMP)31.缺序号(MISSINGS/N)32.序号错(WRONGS/N)34.标示错(WRONGMARK)35.脚太短(PINSHORT)36.J1不洁(J1DIRTY)37.锡凹陷(SOLDERSCOOPED)38.线序错(W/LOFWIRE)39.未测试(NOTEST)40.VR变形(VRDEFORMED)41.PCB翘皮(PCB PEELING)42.PCB弯曲(PCB TWIST)43.零件沾胶(GLUEONPARTS)44.零件脚长(PARTSPINLONG)45.浮件(PART SLIFT)46.零件歪斜(PARTSTILT)47.零件相触(PARTSTOUCH)48.零件变形(PARTSDEFORMED)49.零件损坏(PARTSDAMAGED)50.零件脚脏(PINDIRTY)51.零件多装(PARTSEXCESS)52.零件沾锡(SOLDERONPARTS)53.零件偏移(PARTSSHIFT)54.包装错误(WRONGPACKING)55.印章错误(WRONGSTAMPS)56.尺寸错误(DIMENSIONWRONG)57.二极管坏(DIODENG)58.晶体管坏(TRANSISTORNG)59.振荡器坏(X’TLNG)60.管装错误(TUBESWRONG)61.阻值错误(IMPEDANCEWRONG)62.版本错误(REVWRONG)63.电测不良(TESTFAILURE)64.版本未标(NONREVLEBEL)65.包装损坏(PACKINGDAMAGED)66.印章模糊(STAMPSDEFECTIVE)67.卷标歪斜(LABELTILT)68.外箱损坏(CARTONDAMAGED)69.点胶不良(POORGLUE)70.IC座氧化(SOCKETRUST)71.缺UL卷标(MISSINGULLABEL)72.线材不良(WIREFAILURE)73.零件脚损坏(PINDAMAGED)74.金手指沾锡(SOLDERONGOLDENFINGERS)76.包装数量错(PACKINGQ’TYWRONG)77.零件未定位(PARTSUNSEATED)79.垫片安装不良(WASHERUNSEATED)80.线材安装不良(WIREUNSEATED)。
PCB常见不良中英文对照电子厂专业术语
WINDOWS不能軟體關機 QAPLUS 當機 音效不良 VGA不良或螢冪雜訊 USB不良 凹痕
英文 CACHE MEMORY defect cann't read floppy IDE1 cann't read or error KEYBOARD LOCK error GspReEeEdNeerrroror ror cann't switch LED no light or error speaker error or disorder COM 1/2 defect LPT1 defect CMOS setting error time stopped ID 00 defect CARD defect WINDOWS hang up WINDOWS cann't boot from software QAPLUS hang up audio error VGA error or disorder USB defect sink mark
電源短路 CPU速度不對 MEMORY不良 KEYBOARD不良 HIMEM ERROR或當機 凹孔 條狀痕 表面裂痕 橘皮狀表皮皺摺粗糙 波動 冒汗 扭曲 翹曲 波痕 熔塌 焊痕 白化 皺紋
pock mark resin streak resin wear riding sagging saponification scar scrap scrap jam scratch scuffing seam shock line short shot
英文 PCB defect soldering open short missing wrong component invert position shift component shift reverse tombstone component side up solder ball extra soldering poor soldering bar code defect
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
常見不良現象中英文對照表
英文 poor solder mask PAD defect forming defect board bent extra component component deform ICT test fail voltage defect no voltage wire open no boot BIOS flash error cann't flash BIOS cann't RESET battery no voltage
中文 CACHE MEMORY不良 A磁碟機不讀 IDE1硬碟機不讀或不抓 KEYBOARD LOCK不良 GREEN不良 速度不對或不能切換 LED燈不亮或不良 喇叭不叫或亂叫 COM 1/2不良 LPT1不良 CMOS設定不良 時間不動 ID 00不良 CARD不良 WINDOWS當機
power short CPU frequency error MEMORY defect KEYBOARD defect HIMEM ERROR or hang up shrinkage pool streak surface check surface roughening surging sweat out torsion warpage waviness webbing weld mant G/F scratch G/F residue glue G/F etching defect
中文 PCB不良 空焊 短路 缺件 錯件 反向 位移 偏移 翻面 立碑 側立 錫球 錫多 吃錫不良 條碼不良
殘留助焊劑 板面不澍 零件破損 溢錫 零件氧化 矯直 色差 霧化 凸料紋 咬入 塗料孔(鑄疵) 塗料疤 起泡 起霜 泛白 皺紋 冒口帶肉 膜泡 糊斑 毛邊 毛邊 翹曲 表面中部波皺 細裂痕 龜裂 修整表面缺陷 鑄件凹痕
英文 PCB defect soldering open short missing wrong component invert position shift component shift reverse tombstone component side up solder ball extra soldering poor soldering bar code defect
電源短路 CPU速度不對 MEMORY不良 KEYBOARD不良 HIMEM ERROR或當機 凹孔 條狀痕 表面裂痕 橘皮狀表皮皺摺粗糙 波動 冒汗 扭曲 翹曲 波痕 熔塌 焊痕 白化 皺紋
pock mark resin streak resin wear riding sagging saponification scar scrap scrap jam scratch scuffing seam shock line short shot
冷焊 反白 點膠不良 撞件 線路不良 表皮摺疊 毛邊 光滑 光澤 汙斑 磨痕 發裂 霧度 水銹 壓痕 內部氣孔 偏模/不吻合 斑點 縮頸 割痕 橘皮狀表面缺陷 溢流 剝離 坑 點狀腐蝕 模板印痕 麻點
塌陷 色斑 腐蝕 裂痕 龜裂 變形 切邊碎片 裂邊 退色 填充料斑 裂紋 凸緣起皺 刮傷 流痕
collapse color mottle corrosion crack crazing deformation edge edge crack fading filler speak fissure flange wrinkle flaw flow mark
中文 防焊不良 PAD不良 成型不良 板彎板翹 多件 零件變形 ICT測試不良 電壓不良 無電壓顯示 燒斷線 不開機 BIOS燒錄不良 不能燒BIOS 不能RESET 電池沒電
常見不良現象中英文對照表
cold soldering reverse bounding defect component crash circuit defect skin inclusion galling glazing gloss grease pits grinding defect haircrack haze incrustation indentation internal porosity mismatch mottle necking nick orange peel overflow peeling pit pitting corrosion plate mark pock
英文 Game Port defect cann't burn in Lan number Lan function test error 1394 error AMR FAIL CNR FAIL BEAR ERROR NUMBER LCD ERROR leakage current ACPI detect error Case Open defect SCR defect CHIP ID ERROR others G/F adhere stannum
痘斑 樹脂流紋 樹脂脫落 凹陷 松垂 皂化 疤痕 廢料 廢料阻塞 刮傷/劃痕 深沖表面劃傷 裂痕 模口擠痕 充填不足
英文 mixed boards mixed versions component lead float illegible character float lead knee down lead doesn't penetrate incoming matrials defect lead longer solder hole solder splash solder tail extra soldering non-wetting hole clog
中文 混板 混版 零件翹腳 文字面不良 浮高 折腳 腳未出 原材不良 腳長 錫洞 錫渣 錫尖 包焊 拒焊 孔塞
residue flux PCB surface dirty component broken overflowing component oxidized straightening aberration atomization bank mark bite blacking hole blacking scab blister blooming blushing body wrinkle breaking-in bubble burn mark burr burr(金屬) flash(塑件) camber center buckle check checking chipping clamp-off
中文 Game Port不良 不能燒網路號碼 網絡功能不良 1394不良 AMR FAIL CNR FAIL BEAR ERROR NUMBER LCD ERROR 漏電流 ACPI 偵側不良 Case Open不良 SCR不良 CHIP ID ERROR 其他 金手指沾錫
金手指凹陷 金手指刮傷 金手指殘膠 金手指缺口
WINDOWS不能軟體關機 QAPLUS 當機 音效不良 VGA不良或螢冪雜訊 USB不良 凹痕
英文 CACHE MEMORY defect cann't read floppy IDE1 cann't read or error KEYBOARD LOCK error GspReEeEdNeerrroror ror cann't switch LED no light or error speaker error or disorder COM 1/2 defect LPT1 defect CMOS setting error time stopped ID 00 defect CARD defect WINDOWS hang up WINDOWS cann't boot from software QAPLUS hang up audio error VGA error or disorder USB defect sink mark