连接器相关的常用英语

一:常用術語Engineer standard 工標Document center (database center)資料中心Design Center 設計中心Painting 烤漆(廠) Assembly組裝(廠)Stamping 沖壓(廠)Education and Training 教育訓練proposal improvement/creative suggestion 提案改善Technological exchange and study 技術交流研習會Technology and Development Committee 技術發展委員會BS Brain Storming 腦力激蕩QCC Quality Control Circle 品質圈PDCA Plan Do Check Action 計劃執行檢查總結DCC delivery control center 交貨管制中心3CComputer 電腦類產品Consumer electronics 消費性電子產品Communication 通訊類產品FOUR CONTROL YSTEM 四大管制系統Engineering control system 工程管制系統Quality control system 品質管制系統Manufacturing control system 生產管制系統Management control system 經營管制系統7SClassification 整理(sorting, organization)-seiriRegulation 整頓(arrangement, tidiness)-seitonCleanliness 清掃(sweeping, purity)-seisoConservation 清洁(cleaning, cleanliness)-seiktsuCulture 教養(discipline)-shitsukeSave 節約Safety 安全二:英文縮寫品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理PQ passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認CP capability index 能力指數CPK capability process index 模具製程能力參數SSQA standardized supplier quality audit 合格供應商品質評估FMEA failure model effectiveness analysis 失效模式分析FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的Q/R/S Quality/Reliability/Service 品質/可靠度/服務P/N Part Number 料號L/N Lot Number 批號AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件檢查報告PPM Percent Per Million 百萬分之一制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制GRR Gauge Reproductiveness & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑N Number 樣品數其它品質術語類QIT Quality Improvement Team 品質改善小組ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理RMA Return Material Audit 退料認可7QCTools 7 Quality Control Tools 品管七大手法通用之件類ECN Engineering Change Notice 工程變更通知(供應商) ECO Engineering Change Order 工程改動要求(客戶) PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Standard Inspection Procedure 製程檢驗標準程序SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類ES Engineering Standard 工程標準IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格部類PMC Production & Material Control 生產和物料控制PCC Product control center 生產管制中心PPC Production Plan Control 生產計劃控制MC Material Control 物料控制DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部生產類PCS Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號OEM Original Equipment Manufacture 原始設備製造商PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量I/O input/output 輸入/輸出NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許APP Approve 核準,認可,承認CHK Check 確認ASS'Y Assembly 裝配,組裝T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率SPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal Display 液晶顯示器CAD Computer Aided Design 計算機輔助設計CAM Computer Aided Manufacturing 計算機輔助製造CAE Computer Aided Engineering 計算機輔助工程PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WDR Weekly Delivery Requirement 周出貨要求PPM Percent Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OS Operation System 作業系統TBA To Be Assured 待定,定缺D/C Drawing Change 圖面變更P/P Plans & ProcedureEMI Electrical-Music Industry 電子音樂工業Electrical Magnetic Interference 電子干扰RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 發光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessA VL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving note 貨物收貨單A/R Account receivable 應收款A/P Account payable 應付款三:專業詞匯通用類President 董事長Operator 作業員Position 職務G eneral manager 總經理special assistant 特助deputy manager |'depjuti|=vice manager 副理deputy supervisor =vice supervisor 副課長group leader 組長line leader 線長supervisor 課長responsible department負責單位Human Resources Department 人力資源部Head count 人頭數production department生產部門planning department企劃部QC Section品管課stamping factory沖壓廠painting factory烤漆廠molding factory成型廠administration/general affairs dept./ 總務部production unit生產單位meeting minutes會議記錄distribution department分發單位subject 主題conclusion 結論decision items 決議事項pre-fixed finishing date預定完成日Color management 顏色管理Visual management 目視管理production capacity生產力first count初盤first check初盤復櫂second count 復盤second check 復盤復核quantity of physical inventory second count 復盤點數量physical inventory 盤點數量physical count quantity帳面數量difference quantity 差異量spare parts physical inventorylist 備品盤點清單cause analysis 原因分析waste materials 廢料description 品名specification 規格model 機種work order 工令revision 版次remark備注registration登記registration card 登記卡to control 管制applicationformforpurconsume, consumption消耗to notify 通知to fill in 填寫to collect, to gather 收集statistics 統計cosmetic inspection standard外觀檢驗規範computer case 電腦外殼(組件)personal computer enclosure電腦機箱產品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上蓋base pan 基座bezel 面板riser card 擴充卡flat cable 排線TOP driver cage 上磁架bottom driver cage 下磁架resin film 樹脂膜raw materials 原料materials 物料steel plate 鋼板roll/coil material 捲料spare parts =buffer 備品plastic parts 塑膠件sheet metal parts/stamping parts沖件material check list物料檢查表finished product 成品semi-finished product半成品good product/accepted goods/accepted parts/good parts良品defective product/non-goodparts 不良品disposed goods 處理品warehouse/hub 倉庫packing material 包材basket 蝴蝶竺plastic basket 膠筐flow chart 流程表單production tempo 生產進度現狀lots of production 生產批量manufacture procedure制程to revise, modify 修訂to switch over to, switch—to,switching over 切換engineering bottleneck, projectdifficulty 工程瓶頸glove(s) 手套glove(s)wiBand-Aid創可貼Industrial alcohol工業酒精Broom 掃把Mop 拖把vacuum cleaner 吸塵器rag 抹布garbage container 灰箕garbage can 垃圾箱garbage bag 垃圾袋liaison 聯絡單rags 抹布lamp holder 燈架to mop the floor 拖地to clean a table 擦桌子air pipe 氣管delivery deadline 交貨期die worke 模工production, to produce 生產equipment 設備resistance 電阻beacon 警示燈coolant 冷卻液crusher 破碎機club car 餐車plate 電鍍power button 電源按鍵reset button 重置鍵forklift 叉車Workshop traveler天車（行車）trailer =long vehicle 拖板車Hydraulic trolley 手壓車hydraulic hand jack油壓板車casing = containerization 裝箱velocity 速度patent 專利coordinate 座標supply and demand 供求career card 履歷卡barricade 隔板carton box 紙箱to pull and stretch 拉深work cell/work shop 工作間sub-line 支線bottleneck 瓶頸模具工程類plain die 簡易模pierce die 沖孔模forming die 成型模progressive die 連續模stage die 工程模compound die 復合模shearing die 剪邊模riveting die 鉚合模feature die 公母模male die 公模female die 母模cavity 型控母模core 模心公模die change 換模to fix a die 裝模to repair a die 修模punch set 上模座punch pad 上墊板punch holder 上夾板stripper pad 脫料背板up stripper 上脫料板upper plate 上模板lower plate 下模板die pad 下墊板die holder 下夾板die set 下模座bottom block 下墊腳bottom plate 下托板(底板)upper supporting blank上承板upper padding plate blank上墊板top plate 上托板（頂板）top block 上墊腳stripping plate 內外打(脫料板)outer stripper 外脫料板inner stripper 內脫料板lower stripper 下脫料板punch 沖頭insert 入塊(嵌入件)deburring punch 壓毛邊沖子groove punch 壓線沖子stamped punch 字模沖子round punch 圓沖子special shape punch 異形沖子bending block 折刀roller 滾軸baffle plate 擋塊located block 定位塊supporting block for location定位支承塊air cushion plate 氣墊板air-cushion eject-rod氣墊頂桿trimming punch 切邊沖子stiffening rib punch = stinger加強筋衝子ribbon punch 壓筋沖子reel-stretch punch卷圓壓平沖子guide plate 定位板sliding block 滑塊sliding dowel block滑塊固定塊die locker 鎖模器pressure plate =plate pinch壓板thickness gauge 厚薄規cutting die, blanking die沖裁模die block 模塊folded block 折彎塊sliding block 滑塊location pin 定位銷lifting pin 頂料銷die plate, front board 模板padding block 墊塊stepping bar 墊條panel board 鑲塊to load a die 裝上模具to unload a die 御模具active plate 活動板lower sliding plate 下滑塊板upper holder block 上壓塊upper mid plate 上中間板spring box 彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing block 襯套cover plate 蓋板guide pad 導料塊pilot 導正筒trim 剪外邊pierce 剪內邊pocket for the punch head挂鉤槽slug hole 廢料孔radius 半徑shim/wedge/heel/pad/spacer/gas ket 楔子torch-flame cut 火焰切割set screw 止付螺絲form block 折刀round pierce punch =die button圓沖子shape punch =die insert異形子stock located block 定位塊metal plate 鈑金miller 銑床grinder 磨床tolerance 公差score =groove 壓線sliding block滑塊lathe車active plate 活動板baffle plate 擋塊cover plate 蓋板groove punch 壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板capability 能力parameter 參數factor 系數driller 鉆床set up die 架模height of die setting up架模高度analog-mode device 類模器inner guiding post 內導柱inner hexagon screw內六角螺釘dowel pin 固定銷coil spring 彈簧lifter pin 頂料銷eq-height sleeves =spool等高套筒pin銷lifter guide pin 浮升導料銷guide pin 導正銷wire spring 圓線彈簧outer guiding post 外導柱stop screw 止付螺絲located pin 定位銷outer bush 外導套press specification 沖床規格die height 閉模高度flow mark 流痕welding mark 溶合痕post screw insert螺紋套筒埋值self tapping screw 自攻螺絲stripper plate 脫料板piston 活塞handle mold 手持式模具flash mold 溢流式模具positive mold 擠壓式模具split mold 分割式模具die lifter 舉模器top stop 上死點bottom stop 下死點one stroke 一行程to continue, cont. 連動to grip(material) 吸料location lump, locating piece,location block 定位塊reset 復位to file burr 銼毛刺embedded lump |in'bed| |l mp|鑲塊stamping-missing 漏沖to tight a bolt 擰緊螺栓to loosen a bolt 擰鬆螺栓punched hole 沖孔to cut edge =side cut =side scrap切邊to bending 折彎to pull, to stretch 拉伸engraving, to engrave 刻印stamping 油印to stake 鉚合designing, to design 設計design modification設計脩改成gauge(or jig) 治具pedal 踩踏板stopper 阻擋器flow board 流水板torque 扭矩spline =the multiple keys花鍵quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy 合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的forming成型(抽凸,沖凸)draw hole 抽孔bending 折彎emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線stamp letter沖字(料號) tick-mark nearside正面壓印tick-mark farside反面壓印extension DWG展開圖procedure DWG工程圖die structure DWG模具結構圖沖壓類punch, press沖punching machine 沖床hydraulic machine油壓機jack升降機decoiler整平機manufacture management製造管理stamping, press沖壓feeder送料機rack, shelf, stack料架taker取料機to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|報廢scrape ..v.刮;削robot機械手production line流水線packaging tool打包機packaging打包成型類well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道welding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleeve套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口diaphragm gate隔膜澆口ring gate環形澆口submarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口runner less無澆道sprue less 無射料管方式long nozzle延長噴嘴方式spur澆口;溶waste廢料board看板sliding rack滑料架to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料material change, stock change材料變更feature change 特性變更prepare for, make preparations for準備rotating speed, revolution轉速abnormal handling異常處理組裝類Assembly line組裝線Layout布置圖Conveyer流水線運輸帶Rivet machine 拉釘機 Rivet gun 拉釘槍 Screw driver 起子Electric screw driver 電動起子 Hydraulic machine 液壓機 Pn e u m a t i c s c r e w d r i v e r 氣 automation 自動化to stake, staking, riveting 鉚合 add lubricant oil 加潤滑油 argon welding 氬焊 cylinder 油缸 robot 機械手 conveying belt 輸送帶 transmission rack 輸送架 to draw holes 抽孔 bolt 螺栓 nut 螺母 screw 螺絲identification tag 標示單 screwdriver plug 起子插座 automatic screwdriver 電動啟子 to move, to carry, to handle 搬運 be put in storage 入庫 packing 包裝staker = riveting machine 鉚合機 fit together 組裝在一起 fasten 鎖緊(螺絲) fixture 夾具(治具) pallet/skid 棧板 barcode 條碼barcode scanner 條碼掃描器 fuse together 熔合fuse machine/heat stake 熱熔機 processing, to process 加工 delivery, to deliver 交貨to return delivery to. to send de l i v e r y b a ck t o r e t u r n o f g o o deasily damaged parts 易損件 standard parts 標準件 to lubricate 潤滑 spring 彈簧spare tools location/buffer 手工備品倉spare molds location 模具備品倉 tox machine 自鉚機烤漆類 phosphate 皮膜化成 viscosity 涂料粘度 alkalidipping 脫脂 main manifold 主集流脈 organic solvent 有機溶劑 demagnetization 去磁;消磁 high-speed transmission 高速傳遞 heat dissipation 熱傳 rack 上料 volatile 揮發性 degrease 脫脂rinse 水洗 alkaline etch 齡咬 desmot 剝黑膜 D.I. rinse 純水次 Chromate 鉻酸處理 Anodize 陽性處理 seal 封孔scraped products 報放品 disposed products 處理品 dismantle the die 折模 auxiliary function 輔助功能 heater band 加熱片 thermocouple 熱電偶 derusting machine 除銹機 degate 打澆口 dryer 烘干機 induction 感應 induction light 感應光 response =reaction =interaction 感應 ram 連杆 edge finder 巡邊器 concave 凸convex 凹 cold slug 冷塊 blush 導色 gouge 溝槽;鑿槽 satin texture 段面咬花 witness line 證示線 grit沙礫 granule =pellet =grain 細粒 sand blasting 噴沙 grit maker 抽粒機 cushion 緩沖 fillet 鑲;嵌邊roller pin formality 滾針形式 cam driver 鍘楔 shank 摸柄 crank shaft 曲柄軸品質類qualified products, up-to-grade products 良品defective products, not up-to-grade products 不良品defective product box 不良品箱 poor processing 制程不良poor incoming part來件不良exposed metal/bare metal金屬裸露excessive defect過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格cosmetic defect外觀不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑絲missing part漏件wrong part錯件oxidation氧化defective threading抽芽不良poor staking鉚合不良deficient purchase來料不良deficient manufacturing procedure 制程不良cosmetic inspection外觀檢查inner parts inspection內部檢查blister 氣泡angular offset 角度偏差dent 壓痕scratch 刮傷deformation 變形filings 鐵削defective label 不良標簽abrasion 磨損Breaking. (be)broken,(be)cracked斷裂short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delaminating起鱗speckle斑點mildewed =moldy = mouldy發霉deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excessive gap間隙過大grease/oil stains油污inclusion雜質shrinking/shrinkage縮水mixed color雜色fold of packaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬impurity 雜質Mismatch 錯位failure, trouble 故障deformation 變形rust 生銹peel 脫漆Shrink 縮水Contamination 臟污water spots 水漬Gap 間隙label error 標簽錯誤Missing label 漏貼rejection criteria 拒收標准Suspected rejects 可疑庇abrasion 損傷、磨損Texture surface 印花紋表面Streak 條紋stains 污點Blotch 斑點discoloration 脫色Inclusion 雜質slug mark 壓痕dirt grime 灰塵blush 毛邊薄膜sink 下凹Hickey 漏漆labels and logos 貼紙與商標Configuration labels 組合貼紙corrugated container 瓦擺紙箱Delaminating 脫層splattering 散點Gouge 銼孔puckering 折痕CONNECTOR中英文對照表。