流量开关选型手册
HD1K-015GM040流量开关选型手册
HD1K-015GM040流量开关选型手册
1、有挡板式（可显示流量）。
2、浮子式。
3、金属转子式（可显示流量）。
4、粘度补偿式。
5、旋叶式（可显示流量）。
6、热式流量开关（可显示流量）。
7、亦可用插入式电磁流量计式。
那么流量开关该如何选型呢？
选择合适的流量开关除了根据自己需求功能选型之外，还应根据流体工况特性、安装要求、环境条件、经济性等因素合理选型。
①安装环境。
现场安装环境主要指测量管径大小、直管段长度、管道是否有振动、周围是否有强磁场干扰和高温辐射热等。
②安全性。
防止事故发生。
比如，测量腐蚀性介质时，根据腐蚀性强度选用合适的内衬材质，可燃性气体的环境应选用防爆型仪表。
③节能性。
流体经过流量仪表前后的压损，压损值越小节能性越好。
非接触式如超声波流量计、电磁流量计、弯管流量计无压损。
④流体特性。
流体特性主要指流体成分、温度、压力、黏度等。
根据实际情况逐步确认选型范围。
首先从成分（液体、气体、蒸汽、脏流污程度）区分，差压式流量计和涡街流量计基本适应以上流体。
⑤准确性和经济性。
一般本身其性能相对稳定、重复性好、使用寿命较长、量程比范围宽的流量计有利于后期增加工艺设备测量参数调节，从而减少投资。
电磁式数字流量开关lfef系列使用说明书
文件No.LFE****-OMY0008电磁式数字流量开关LFE####有限公司SMC有限公司安全注意事项 2 型式表示・型号体系 11 产品各部分名称及功能 13 用语说明 14 安装·设置 16 安装方法 18 配管方法 19 配线方法 21 流量设定 24 功能设定 26 出厂时的设定 26 F1 OUT1设定 28 F2 OUT2设定 36 F3响应时间设定 40 F10子画面的显示内容选择 41 F20外部输入设定 45 F22模拟输出设定 46 F30累计保持功能 47 F32流动方向设定功能 48 F33密接安装设定 50 F34复零设定 51 F80省电模式设定 52 F81 密码输入设定 53 F82 生产线名的输入 54 F90 全项目设定 55 F98 输出确认 56 F99 恢复出厂设置 57 其他设定 58 保养 60 故障一览表 61 规格 64 适用流体 66 特性表 67 模拟输出 70 外形尺寸图 71此处所示的注意事项是为了确保您能安全正确地使用本产品，预先防止对您和他人造成危害和损失而制定的。
这些注意事项，按照危害和损伤的大小及紧急程度分为「注意」「警告」「危险」三个等级。
无论哪个都是与安全相关的重要内容，所以除了遵守国际规格(ISO/IEC)、日本工业规格(JIS)※1）以及其他安全法规※2）外，这些内容也请务必遵守。
※1) ISO 4414:Pneumatic fluid power -- General rules relating to systems.ISO 4413:Hydraulic fluid power -- General rules relating to systems.IEC 60204-1:Safety of machinery --Electrical equipment of machines. (Part1:General requirements) ISO 10218-1992:Manipulating industrial robots -Safety JIS B 8370:空气压系统通则 JIS B 8361:油压系统通则JIS B 9960-1:机械类的安全性-机械的电气装置((第1部:一般要求事项) JIS B 8433-1993:工业用操作机器人－安全性等 ※2) 劳动安全卫生法等注意:误操作时，有人员受伤的风险，以及仅有物品破损的风险的事项。
MFM500D流量开关选型V1.0
传真：0917-3600755
3 GND (黑色) RL RL
2 PNP1 (黄色) 1 24VDC+ (红色) 4 PNP2 (蓝色)
-3-
MFM500D 型流量开关选型（V1.1）
选型指南
MFM500D
型流量开关 代号 供电电源
DC 24VDC AC 220VAC（继电器输出）
代号 压力接口形式 C1 M20×1.5 外螺纹 C3 G1/2 外螺纹
水 温：-20℃～80℃ 贮存温度：-30℃～85℃ 工作温度：-20℃～70℃ 防护等级：IP67 温度补偿：5℃～50℃补偿（水） 电磁兼容：GB/T 17626.2/3-2006，GB/T 17626.4-2008 振 动：≤ 20g (GB/T 2423.10-2008) 冲 击：≤ 50g/11ms (GB/T 2423.5-1995)
24V DC供电
24V DC供电
NPN输出
1 24VDC+ (红色) RL RL
2 NPN1 (黄色)
3 GND (黑色)
4 NPN2 (蓝色)
PNP输出
地址：陕西省宝鸡市高新开发区英达路 18 号 721006
电话：0917-3600901 3600902 3600903
MFM500D 型流量开关选型（V1.1）
MFM500D 型流量开关
产品特点
· 24VDC 或 220VAC 宽范围供电可选 · LED 液晶屏，数字百分比显示 · 全不锈钢外壳，IP67 防护 · 温度补偿 · 多种输出方式可选 · 无可动部件，免维护 · 开关量输出，控制点连续可调 · 外形小巧，支持显示反转 · 活接头可配不同接口，适合多种管径要求
选型提示
管道流量开关选型手册
1.5 1.0 1.0 1.0 2.0 1.5 2.0 3.0 2.5 2.5 2.5 3.0 3.0 3.5 3.5 3.0 4.5 4.0
流量开关
6.仪表材质
表体 传动机构 测量系统 密封垫 仪表外壳
304/316 304/316 304/316 PTFE
塑料
304/316 304/316 304/316 PTFE
编号
1501 1502 1503 1504 1505 1506 1507 2501 2502 2503 2504 4001 4002 4003 4004 5001 5002 5003 5003 5004
流量范围(m3/h)
10-40 12-50 16-60 20-70 15-60 20-80 25-100 30-120 25-100 30-120 40-150 45-180 40-150 45-180 60-220 65-250 50-220 70-250
编号
8001 8002 8003 8004 10001 10002 10003 10004 12501 12502 12503 12504 15001 15002 15003 15004 20001 20002
压力损失 △Pmax(kPa)
8.5 12.0 15.0 20.0 45.0 45.0 45.0 10.0 20.0 30.0 40.0 7.0 11.0 13.0 15.0 8.0 25.0 35.0 38.0 40.0
2.特点
· 流线型结构设计、坚固耐用。 · 磁性耦合测量系统。 · 安装方向任意；垂直、水平安装任意。 · 多种材料的选择。 · 测量量程宽广。 · 清晰的流量显示刻度、读取方便，旋转指针。
E+H流量仪表选型手册
作
应用广泛 ·一体化型流量监控仪适用于所有应用场合 ·可安装在：
钢质管道上（最小管径为DN25） 塑料管道上（最小管径为DN15）
操作简便 ·通过旋转开关设定开关点 ·现场设定满量程值 ·可在安装前对仪表进行设置
Endress + Hauser
Magphant
操作
测试模式
设定界限值 以满量程值百分比 形式设定
红 色L CD 用于指示界限值或报错显示
绿色L CD 用于指示是否超出满量程
满量程调钮
操作显示界面
时间常数， 电流输出 及继电器响应时间
继电器功能， 出错，到达 设定值时动作
最小/最大值 ，故 障 保护
IEC 758
热参数和 温度 等级 （适用于 防爆2区）
T环 境 T介质（ 参 见 下述 说 明）
7
Endress + Hauser
Magphant
产品选型
补充资料
型号/探 头垫 圈 A1 双端 螺母 ，适 用于DN25...2000（1″...80″ ）
（仅适用于焊接连接方式） A2 适用 于管 径为DN15…1000（1/2″…40″ ）的 塑料 管道
25℃时为16 bar；120℃时为10 bar
1...5 m/s（无级变速）
读数值的±2%（流率＞1 m/s的介质，现场标定）
读数值的±2%
≥20 μS/cm
符合CE EN 50081-1-2和EN 50082-1-2
IP 66 / NEMA 4X/ 4X 型
材料 传 感 器传 感 器 头
FSW300系列流量开关说明书
FSW300 Series Starts at
£90
Adjustable Switch Point
Low Pressure Drop
Economical
Field Installation for 1⁄2 to 8" Pipes
Instant Response
Dimensions (Excluding Paddle or Tee): 114 x 38 x 89 mm (4.5 x 1.5 x 3.5")
SPECIFICATIONS FSW302, 303, 304
Max Pressure: 25 bar (362 psi)
Max Process Temp: 110°C (230°F)
4.9 to 6.8 (1.3 to 1.8) 9.5 to 12.1 (2.5 to 3.2) 10.6 to 14.8 (2.8 to 3.9)
Comes complete with operator’s manual. Ordering Example: FSW305-G, inline flow switch, 1⁄2" PVC tee connection, 70A-2, audible alarm, £90 + 10.75 = £100.75
Comes complete with operator's manual.
Ordering Example: FSW301, insertion style flow switch and 70A-2, fast pulse tone alarm, £90 + 10.75 = £100.75
B-75
流量开关规格书
35
36
37
38
39
40
41
42 43 推荐制造商 Manufacturer
其他 Miscell
44
45
46 说明 NOTES：
档案号PROJECT No： 设计阶段 STAGE: 页数PAGE:
版本 FA
REV
最大 MaxFlow
正常 NorFlow 最小MinFlow
标准密度 Std. Density k动g/力m粘3n度 Dyn Visc(mPa.s)
工艺条件 Process Condition
13
14
15
16
流量开关 Flow Switch
17
18 型号 Model
型式 Type
19 公称直径 DN (mm)
20 压力等级 Pressure Rating MPa
21 操作温度Oper. Temp.℃ 最大Max.
22 精度 Accuracy
23 连nn. Size
25 法兰标准 Flange STD.
等级 Rating
26 法兰材质 Flange Mat'l
密封面 Facing
27 本体材质 Body Mat'l
仪表规格书（流量开关） INSTRUMENT SPECIFICATION
(FLOW SWITCH)
1 仪表名称 Instrument Name
概况 General
2 位号 Tag Number 3 检测位置 Service 4 工艺管线尺寸Pipe Size mm 外径/内径 O.D/I.D 5 工艺管道材质Pipe Mat'l 管道等级 Class
28 电源 Power Supply
威卡（WIKA）电子流量开关FSD-3型说明书
流量威卡 (WIKA) 数据资料 FL 80.01第 1/7 页电子流量开关带显示，用于液体介质FSD-3 型数据手册中显示了同类产品：带显示的电子压力开关，PSD-4 型，具体情况请参见数据手册 PE 81.86带显示的温度开关，TSD-30 型，具体情况请参见数据手册 TE 67.03带显示的液位开关，LSD-30 型，具体情况请参见数据手册 LM 40.01威卡 (WIKA) 数据资料 FL 80.01 ∙ 12/2017应用■控制冷却润滑系统 ■监控冷却回路控制过滤器单元■ ■泵的空转保护产品特性■ ■支持流量、温度和诊断的开关和模拟输出可靠监测液体介质的流量■通过自带数显仪轻松实现参数化 ■无运动部件，无磨损描述在设计和功能上获得奖项PSD-30 曾摘得 “iF 产品设计奖” 桂冠，这充分证明威卡 (WIKA) 开关产品系列的成功的设计和出色的功能已得到专业认可。
坚固耐用的 LED 显示屏支持 9 mm 高（目前最大的）的字符显示，且字符稍有倾斜，使得用户能远距离轻松读取。
简单直观的 3 键式菜单导航系统，无需其它辅助设备，并且菜单导航符合 VDMA 标准。
无磨损FSD-3 基于量热测量原理，无任何运动部件，可实现无磨损测量。
液体介质流量监测FSD-3 能可靠监测液体介质流量，有助于确保过程安全。
当流量高于或低于设定值时，FSD-3 的开关输出会激活下游的调节器或控制装置，从而防止由于泵、刀具和主轴减速而导致的人员伤害或生产受损。
温度监测FSD-3 还能监测介质温度并输出相关数据，无需其它测量设备。
诊断功能当检测到传感器缺陷时，可选的诊断功能能可靠地输出报警信号，以及时触发下游安全功能。
电子流量开关FSD-3型测量范围流速水： 5...150 cm/s油： 3...300 cm/s出厂默认设置是以水作为介质进行的。
建议通过菜单根据系统的最小/最大流量来进行此调节。
温度（可选项）-20 ... +85 °C (-4 ... +185 °F)数显14 段 LED，红色，4 位，字符尺寸 9mm（0.35 英寸）显示器可电子控制转动 180°输出信号模拟信号（可选）4 ... 20 mA电路标度温度（可选项）零点：-20 ... +5 °C (-4 ... +41 °F)最终值：60...85 °C (140 ...185 °F)开关阈值开关动作点 1 和开关动作点 2 可单独调节开关功能常开，常闭，窗口，回差自由调节开关电压电源 - 1V开关电流最大 250 mA接通偏移10 秒稳定时间流速 (0 ...100 %, 100...0 %)： 6 秒流速 (50...100 %, 100...50 %)： 4 秒温度 t90：4 秒温度 t63：2 秒载荷模拟信号 4...20 mA: ≤ 0.5 kΩ使用寿命1亿次开关周期页码 2/7威卡（WIKA）数据资料 FL 80.01 ∙ 12/2017威卡（WIKA ）数据资料 FL 80.01 ∙ 12/2017页码 5/7供电电压供电电压电源DC 15 ... 35 V电流消耗■有模拟信号的开关输出：175 mA ■无模拟信号的开关输出：150 mA 总电流消耗最大 650mA ，包括开关电流非重复性流量（5...100 cm/s)： ≤ 2 cm/s 温度： ≤ 0.5 K标准条件下的准确度流速 (5 ... ≤ 100 cm/s)： ≤ 测量范围最终值 ±5 %流速 (> 100 ...175 cm/s)： ≤ 测量范围最终值 ±10 %温度： ≤ ±1,5 K包括非线性精度、回差、零点偏移和满量程偏差（与根据 IE C 61298-2 测得的误差值对应）。
SLK智能流量开关选型说明书
SLK智能流量开关使用说明泉州日新流量仪器仪表有限公司选型说明SLK智能流量开关采用应变靶式流量计工作原理，可广泛应用于流体过程控制。
其具备可视化的操作控制界面，用户可根据需要自行设定上下限瞬时流量来控制执行机构；报警方式；还可与电动、气动调节阀互控达到智能控制瞬时流量，实现自动控制调节阀门或执行机构，实现系统自动控制。
1、选型含义表头结构 X：普通型：防爆型外壳材料 Z：碳钢：不锈钢：特定材质公称压力 A：常规型≤2.5MPa特殊型>2.5MPa介质温度 C：常温型 +10℃~+70℃：宽温型 -196℃~+250℃高温型 +250℃~+500℃公称口径为管道公称通径单位为mm介质类型 Y：液体：气体连接方式 G：管锥螺纹式F：法兰连接式D：插入式产品代号：SLK智能流量开关2、技术指标连接方式管锥螺纹式法兰管道式插入式公称口径 DN15~50(1/2″~2″) DN15~300 DN100~2000控制方式上、下限瞬时流量限流控制；智能配合调节执行机构控制上、下限瞬时流量实现期段稳流。
精度等级 2.0； 3.0量程比1：10 1：15输出控制两路常开常闭的开关量输出；250VAC/5A操作方式可视化的操作界面，数字控制一目了然显示方式背光液晶显示：当前瞬时流量工作电压 24VDC防护等级 IP65表头型式防爆型（内置按键操作）普通型（外置按键操作）目录一、概述二、工作原理三、技术原理四、按键功能说明五、操作界面功能1、“功能”键操作界面功能2、“切换”键操作界面功能3、“置零”键操作界面功能4、“系数”键操作界面功能a、上限流量报警值设定b、下限流量报警设定c、报警回差值设定d、报警开关量输出状态设定e、小信号切除设定f、流量系数设定g、报警输出信号方式设定六、安装要求七、调整校对1、零点值刷新2、流出系数调整a 、实流校准b、干式（吊重法）瞬时流量基本误差校验Ⅰ砝码挂重的质量换算Ⅱ标准瞬时流量值计算公式Ⅲ瞬时流量值基本误差Ⅳ流出系数修正八、接线图九、应用举例订货咨询一、概述SLK智能流量开关，是采用应变靶式流量计的计量工作原理，为液晶背光显示界面，具备人机可视操作,用户使用一目了然。
IO-Link数字流量开关操作手册说明书
Before UseDigital Flow SwitchPF3A703H/PF3A706H/PF3A712H-LSafety InstructionsThese safety instructions are intended to prevent hazardous situations and/orequipment damage.These instructions indicate the level of potential hazard with the labels of"Caution", "Warning" or "Danger". They are all important notes for safety and mustbe followed in addition to International standards (ISO/IEC) and other safetyregulations.OperatorThank you for purchasing an SMC PF3A703H/PF3A706H/PF3A712H-L DigitalFlow Switch.Please read this manual carefully before operating the product and make sure youunderstand its capabilities and limitations. Please keep this manual handy forfuture reference.Safety Instructions1324DisplayBody(IN side)Connector pin numbers(on the product)Mounting•Never mount the product in a place that will be used as a mechanical support during piping.•Never mount the product upside down.•Attach the piping so that the fluid flows in the direction indicated by the arrow on the body.•The monitor with integrated display can be rotated.Rotating the display with excessive force will damage the end stop.•Visibility decreases if the display is viewed from the opposite side to the buttons.Check the settings and display from in front of the display.Mounting and InstallationRefer to the product catalogue or SMC website (URL https://) for moredetailed information.IN OUTArrowthe IN side of the product.When installing a regulator at the IN side of the product, make sure that hunting is not generated.•The piping on the IN side must have a straight section of piping whose length is 8 timesthe piping diameter or more.If a straight section of piping is not installed, the accuracy will vary by approximately 3%F.S.•Avoid sudden changes to the pipingsize on the IN side of the product.The accuracy may vary.•Do not release the OUT side pipingport of the product directly to theThe accuracy may vary.○Flow direction○Rotation of the display•Use the correct tightening torque for piping. (Refer to the table below for the requiredtorque values.)•If the tightening torque is exceeded, the product can be damaged.If the tightening torque is insufficient, the fittings may become loose.•Avoid any sealing tape getting inside the fluid passage.•Ensure there is no leakage after piping.•When mounting the fitting, a spanner should be used on the body (metal part) of thefitting only.Holding other parts of the product with a spanner may damage the product.Specifically, make sure that the spanner does not damage the M12 connector.■WiringConnection•Connections should only be made with the power supply turned off.•Use a separate route for the product wiring and any power or high voltage wiring. If wiresand cables are routed together with power or high voltage cables, malfunction may resultdue to noise.•If a commercially available switching power supply is used, be sure to ground the frameground (FG) terminal. If the product is connected to the commercially available switchingpower supply, switching noise will be superimposed and the product specifications will notbe satisfied. In that case, insert a noise filter such as a line noise filter/ ferrite between theswitching power supplies or change the switching power supply to the series power supply.Connecting/Disconnecting•Align the lead wire connector with the connector keygroove, and insert it straight in. Turn the knurled partclockwise. Connection is complete when the knurledpart is fully tightened. Check that the connection is notloose.•To remove the connector, loosen the knurled part andpull the connector straight out.Connector pin numbers (lead wire)Outline of SettingsPower is supplied.∗: If a button operation is not performed for 3 seconds during the setting, the display will flash. (This is toprevent the setting from remaining incomplete if, for instance, an operator were to leave during setting.)∗: 3 step setting mode, simple setting mode and function selection mode settings will reflect on each other.■3 step setting modeIn the3 step setting mode, the set value selected in the sub display and the hysteresiscan be changed in just 3 steps.Switch ONP_1Flow[L/min]H_1settingsWhen shipped, the default setting is as follows.When the flow exceeds the set value [P_1], the switch will be turned ON.When the flow falls below the set value by the amount of hysteresis [H_1] or more, theswitch will turn OFF.If the operation shown below is acceptable, then keep these settings.For more detailed settings, set each function in the function selection mode.(1) Press the S button once when the item to be changed is displayed on the subdisplay.The set value on the sub display (right) will start flashing.S<Operation>[Hysteresis mode]In the 3 step setting mode, the set value (P_1 or n_1) and hysteresis (H_1) can bechanged.Set the items on the sub display (set value and hysteresis) using the ▲ or ▼ buttons.When changing the set value, follow the operation below. The hysteresis setting can bechanged in the same way.(2) Press the ▲ or ▼ button to change the set value.The ▲ button is to increase and the ▼ button is to decrease the set value.●Press the ▲ button once to increase the value by one digit, press and hold tocontinuously increase.●When ▲ and ▼ buttons are pressed simultaneously for 1 second or more, the setvalue is displayed as [ - - - ], and the set value will be set to the same as thedisplayed value automatically. Afterwards, it is possible to adjust the value bypressing ▲ or ▼.●Press the ▼ button once to reduce the value by one digit, press and hold tocontinuously reduce.(3) Press the S button to complete the setting.To change setting, refer to the operation manual from SMC website(URL https://) or contact SMC.<Operation>[Hysteresis mode](1) Press the S button for 1 second or longer(but less than 3 seconds) in measurementmode. [SEt] is displayed on the main display.When the button is released while in the [SEt] display, the current flow value isdisplayed on the main display, [P_1] or [n_1] is displayed on the sub display (left)and the set value is displayed on the sub display (right).(2) Change the set value using the ▲ or ▼ button, and press the SET button to set thevalue. Then, the setting moves to hysteresis setting.(5) Press and hold the S button for 2 seconds or longer to complete the simple setting.(If the button is pressed for less than 2 seconds, the setting will be returned to P_1.)(3) Change the set value with the ▲ or ▼ button, and press the S button to set thevalue. Then, the setting moves to the setting of OUT2.∗1: Selected items of (1) to (4) become valid after pressing the S button.∗2: After enabling the setting by pressing the S button, it is possible to return to measurementmode by pressing the S button for 2 seconds or longer.∗3: When the output mode is set to accumulated pulse, error output or output OFF, the simplesetting mode cannot be used.(the setting returns to measurement mode by releasing the button when [SEt] is displayed.)■Simple setting modeIn the simple setting mode, the set value, hysteresis and delay time can be changed whilechecking the current flow value (main display).(4) Like the setting of OUT1, the setting returns to the setting of OUT2 by pressing theS button after setting the set value and hysteresis.∗: When [F 1] and [F 2] are set to accumulatedpulse output, error output or output OFF [---]will be displayed in the sub screen when[SEt] is displayed. It is not possible to moveto the Simple setting mode.Change the Function Settings∗1: Setting is only possible for models with the units selection function.∗2: [F 2] The OUT2 setting can be set on the product screen, but since there is no OUT2 switch outputfunction as an output specification, it is not possible to output the ON/OFF signal to an external device.∗3: When the 1 switch output type (output specification symbol is L) is used, [F5] is displayed as [---]and cannot be set.1 to 5 V or 0 to 10 V can be selected when the analogue voltage output type is used.Analogue output free range function can be selected.∗4: When Line name is selected, a suitable line name can be input.To change setting, refer to the operation manual from SMC website(URL https://) or contact SMC.■Function selection modeIn measurement mode, press theS button for 3 seconds or longer,to display [F 0].The [F] indicates the mode forchanging each Function Setting.Press the S button for 2 secondsor longer in function selectionmode to return to measurementmode.To change setting, refer to the operation manual from SMC website(URL https://) or contact SMC.○Reset operationThe Accumulated Flow, Peak Value and Bottom Value can be reset.To reset the accumulated value, press the ▼ and S button for 1 second or longer.○Snap shot functionThe current flow rate value can be stored to the switch output ON/OFF set point.When the items on the Sub display (left) are selected in either 3 step setting mode, Simplesetting mode or Setting of each function mode, by pressing the ▲ and ▼ buttonssimultaneously for 1 second or longer, the value of the sub display (right) will show "----",and the values corresponding to the current flow rate are automatically displayed.MaintenanceHow to reset the product after a power loss or when the power has beenunexpectedly removedThe settings for the product are retained in memory prior to the power loss or de-energizingof the product.The output condition is also recoverable to that prior to the power loss or de-energizing.However, this may change depending on the operating environment. Therefore, check thesafety of the whole installation before operating the product.If the installation is using accurate control, wait until the product has warmed up(approximately 10 to 15 minutes) before operation.Refer to the product catalogue or operation manual from SMC website(URL https://) for more information about the product specifications anddimensions.Specifications / Dimensions○Key-lock function(1) Press the S button for 5 seconds or longer in measurement mode. When [oPE] isdisplayed on the main display, release the button.The current setting "LoC" or "UnLoC" will be displayed on the sub display.(2) Select the key locking/un-locking using the ▲ or ▼ button, and press the S button toset.To use each of these functions, refer to the operation manual from SMC website(URL https://) or contact SMC.The IODD file can be downloaded from the SMC website (URL https://).Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.© 2020 SMC Corporation All Rights ReservedAkihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPANPhone: +81 3-5207-8249 Fax: +81 3-5298-5362URL https://PF※※-OMX0003Troubleshootingdisplayed, please contact SMC.Refer to the operation manual from SMC website (URL https://) for moreinformation about troubleshooting.。