安帝力消防报警主机ADL88说明书
Bosch D9068 数字消防报警传输器(DACT)说明书
u12 VDC or 24 VDC operationu Supports multiple reporting formatsu Five user-programmable input points (Class B, Style B)u100-event history bufferu Dual phone line interfaceThe D9068 Fire Communicator is a complete digital alarm communicator transmitter (DACT) for use with compatible fire alarm control panels (FACPs). Use dry contacts or open collector outputs for alarms and communications with the D9068.FunctionsFive Input PointsThe DACT supports five inputs that can be activated by dry contact relays or open collector outputs. Each of these inputs can be configured for one of seven types of conditions: Fire Alarm, Waterflow Alarm, Supervisory, Monitor Alarm, System Fault, AC Failure and Low Battery.System SupervisionThe DACT is supervised with a hardware watchdog circuit. Failure of the control program results in a hardware reset within two seconds. The on‑board trouble relay releases for the duration of the reset (the relay is normally held energized).The DACT's EEPROM memory, input points, and phone lines are automatically tested periodically. The EEPROM checksum is verified every 10 minutes. If the EEPROM checksum fails, a trouble condition is locally annunciated and a trouble report sent.Serial Data Input DialingThe DACT connects through the D9052 Serial Module to the D10024, D10024A, D9024, and D8024 analog FACPs, and transmits by point in all available formats. User InterfaceAn FMR‑DACT‑KEYPAD LCD Keypad connects to a five-pin connector (option bus interface) and is used to program and troubleshoot the D9068. A D7033 Liquid-Crystal Display (LCD) Remote Keypad can also be used.Reporting FormatsThe DACT supports five reporting formats: ModemIIIa2, Contact ID, SIA110, SIA300, and 4/2.Report RoutingThere are six different report groups that can be routed to one of four phone settings. These report groups consist of non-supervisory alarms, supervisory alarms, alarm restorals, resets, supervisory restorals, tests and troubles, and trouble restorals.Reset ReportA reset report is sent when the D9068 resets from any off-normal condition.Phone Line SelectionThe DACT follows a pre‑determined sequence to select between the phone lines. It also implements the new NFPA requirements for alternation of phone lines during test reporting. The DACT maintains a variable that selects either Phone Line 1 or Phone Line 2 for automatic test reports. After each successful test report, the variable switches to select the other phone line.Communication Failed IndicationThe DACT indicates a communication failure after ten attempts to communicate are completed without success. This causes the trouble output to activate and report the fault.History BufferThe DACT has a history buffer that retains up to 100 events. Each event is tagged with the date and time of occurrence. This buffer can be viewed when anFMR‑DACT‑KEYPAD LCD Keypad (or a D7033 LCD Remote Keypad) is connected to the D9068. When the buffer is full, old events are discarded to make room for new events.Lightning SuppressionMOVs and spark gaps suppress lightning surges and static discharges for inputs and telephone interface.Installation/configuration notesCompatible ProductsThe following products are compatible with the D9068 Fire DACT:Category Product ID Product Description Control Panels D7022Conventional FACPD8024Analog FACPD9024Analog FACPD10024Analog FACPD10024A Analog FACP Keypads andAnnunciatorsD7033LCD keypadFMR‑DACT‑KEYPAD LCD keypad Modules D9052Serial interface moduleponent1D9068 board1Metal enclosure (red)1Lightpipe1DCT-HWD hardware kitEnvironmental ConsiderationsMechanical PropertiesOutputsPower Requirements (use power-limited source)Ordering informationD9068 Fire Digital Alarm Communicator Transmitter (DACT)Complete digital alarm communicator transmitter (DACT) for use with compatible fire alarm control panels (FACPs)Order number D9068Represented by:Americas:Europe, Middle East, Africa:Asia-Pacific:China:America Latina:Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180***********************.com Bosch Security Systems B.V.P.O. Box 800025617 BA Eindhoven, The NetherlandsPhone: + 31 40 2577 284Fax: +31 40 2577 330******************************Robert Bosch (SEA) Pte Ltd, SecuritySystems11 Bishan Street 21Singapore 573943Phone: +65 6571 2808Fax: +65 6571 2699*****************************Bosch (Shanghai) Security Systems Ltd.201 Building, No. 333 Fuquan RoadNorth IBPChangning District, Shanghai200335 ChinaPhone +86 21 22181111Fax: +86 21 22182398Robert Bosch Ltda Security Systems DivisionVia Anhanguera, Km 98CEP 13065-900Campinas, Sao Paulo, BrazilPhone: +55 19 2103 2860Fax: +55 19 2103 2862*****************************© Bosch Security Systems 2014 | Data subject to change without notice 2737918475 | en, V2, 04. Sep 2014。
AL8WD 报警主机 说明书
AL8WD 报警主机安装指南1.0 概述AL8WD带有8个有线防区或8个无线防区，1个报警开关输出以及1个可编程输出；以及支持4组用户密码，包括1组主密码，2组用户码、1组开锁密码;通过手机短信和电话提示报警；可遥控器和短信操作。
2.0 规格工作电压： 直流9~15伏工作电流： 30毫安（待机状态）工作温度： -10℃~ +50℃防区响应时间：500毫秒线尾电阻： 10k欧姆防拆装置： 自带外壳/背板防拆开关防拆键： 上电10秒钟之内，如果没有按下防拆键，则该功能失效3.0 安装● AL8WD报警主机内含有手机模块，打开机壳，在手机模块的插卡处插入SIM卡（具体请参考手机模块的章节）。
● 在机壳内含有可充电的电源和备用的蓄电池。
SIM卡安装好后，接通蓄电池的电源，此时主机电源灯会亮并有上电声音提示。
手机模块上电后会过上一段时间后，才有效（具体请参考手机模块的章节）。
4.0 遥控器操作● “B”键：布防，对报警主机进行布防；● “C”键：撤防，对报警主机进行撤防；● “D”键：留守布防，旁路报警主机所允许旁路的防区，同时对报警主机进行布防；注意：此项功能特别适用于您家中配有多个防区（探测器），并且在不同的时间（例如白天或晚上）警戒范围有所区分，您可根据需要有选择性的对部分防区进行设防。
● “A”键：紧急报警，通过总线到中心报警，但不就地报警（即紧急报警时，警号不响）。
注意：为防止用户误操作，按此键必须持续3秒钟以上，报警主机才会响应。
5.0 防区类型AL8WD支持下列防区类型及功能。
立即防区：布防后,触发了立即防区，都会立即报警。
延时防区：布防后，若触发了延时防区，只在所设定的进入/退出延时时间结束之后才会报警；在延时过程中进行撤防，会自动取消报警。
跟随防区：布防后，此防区被触发，如果没有延时防区被触发，则立即报警；若有延时防区被触发，必须等到延时防区报警后方可报警。
电源防区：一直处于激活状态，不论撤布防与否，只要检测到电源探测器掉电就立即短信报警；掉电恢复后，也会短信报警；但就地不报警。
火Lite系列地址式消防报警系统说明书
Fire Solutions Innovation That EnduresFire-Lite® Alarms has a legacyof simple, reliable life-safety systems. By designing advanced technology that’s also easy to use, Fire-Lite makes protecting what matters most easy – year after year. In a world where anything can change in an instant, you can count on the consistency of Fire-Lite.Fire-Lite®- Innovation that Endures.Endurance Series ES-50X and ES-200X• Single SLC that provides support for 50 (ES-50X) or 198 (ES-200X) addressable devices.• Upload/download panel programming database and flash firmware with USB thumb drive.• Support for addressable multi-criteria fire and CO detector. • 4 programmable function keys to save time.• Built-in Class-A capability for all 4 NACs; no optional card required. • Trouble indication for SLC devices not programmed.• Integrated SWIFT display driver and annunciator built-in to panel. • Notification appliance circuits have built-in sync for the industry’s leading manufacturers including System Sensor ®, Wheelock ®, and Gentex ®.Addressable Fire Alarm Control PanelsMS-9600LSand MS-9600UDLS• Up to 159 detectors and 159 control/monitor modules. (total of 318 devices) per SLC (636 with SLC-2LS option card). • LiteSpeed protocol for SLCcommunication polls 10 devices at a time and operateson standard, unshielded wire. • Auto-programmable function reduces installation time. • Advanced fire technology includes sensitivity testingand automatic drift compensation. • 4 programmable Class B and 2 Class A NACs.Fire-Lite Alarm’s innovative, addressable control panels offer a wide range of capabilities to provide superior value and flexibility. They are easy to install and program with notification appliance circuit (NAC) synchronization and enable emergency personnel to quickly locate a fire. The built-in LiteSpeed™ protocol ensures the fastest possible device response times to help reduce property damage and save lives.Emergency Command Center (ECC)Fire-Lite Alarm’s Emergency Command Center (ECC) leverages advanced technology and 60+ years of life-safety experience to deliver critical messages through non-proprietary systems. The ECC is ideal for any building that needs a flexible, multi-zoned, and highly configurable fire evacuation and mass notification system that’s easy to maintain. ECC-50/100 PrimaryOperator Console• Seamless integration and control when connected to select Fire-Lite addressable panels through the ANN/ACS communication bus. • May be used with any UL-listed control panel (messages canbe initiated by using a dry contact or via a fire alarm NAC circuit). • Includes a single 25 volt, 50 watt speaker circuit (upgradableto 100 watts and 2 speaker circuits with optional amplifier). • Speaker circuits are expandable by up to 8 outputs (withan optional ECC-CE6 module). • Can support up to 14 prerecorded messages that are field- programmable for up to 60 seconds of message playback. • Built-in 2 Amp NAC outputwith sync generator.• 8 Command Input Circuitsthat can be used to activatemessages 1 to 8.• Optional amplifier can beconfigured as a backup in theevent the primary amplifier fails.Amplifiers are independentlypowered to eliminate systeminterruption during a short circuitcondition.• Optional transformer conversionmodule available for 70.7 voltspeaker operation.• Supports charging up to 26AHbatteries.ECC-FFTFire Fighter Telephone• Provides supervision, annunciation,and control for up to 24 remotetelephone handsets.• Built-in auto-program featurefor quick installation.• Can be wired for class A (Style 6or Style 7) or class B (Style 4)configuration.• Can be configured for Multi-PhoneJack Audio Circuit supervision.• Allows simultaneous operationof up to 10 firefighter remotehandsets.ECC-50DA, ECC-50BDA, and ECC-125DA Distributed Audio Amplifiers• Externally mounted amplifiers provide an additional 50 or 125 watts of addressable audio power when connected to the ECC-50/100.• Up to 8 distributed amplifiers can be connected to theECC-50/100 for a total of 1100 watts of audio power.• Includes 4 built-in speaker circuits, which are expandable to 8 circuits with an optional ECC-CE4 module (a maximum of 24 audio circuits).• Speaker output voltage is fieldconfigurable on ECC-50DA for either 25 volts or 70.7 volts of operation. • Includes a built-in power supply and backup battery charger. • ECC-50BDA provides 50 watts of power with 50 watts as backup. It can also provide 100 watts of power (100 watts primary and 50 watts of backup power requires ECC-50WBU).ECC-LOCLocal Operator Console • Provides complete control and has an interface similar to the ECC-50/100• Includes built-in microphone for ALL CALL paging along with message and zone control. • A maximum of 8 ECC-LOCs (or combination of other remote display consoles).ECC-RPU Remote Page Unit• Includes built-in microphone for ALL CALL paging along with message control.• A maximum of 8 ECC-RPUs (or combination of other remote display consoles).• Additional 9th button can be used to activate an optional monitor module that can be mounted inside the cabinet for applications such as HVAC shutdown.ECC-RM Remote Microphone• Includes built-in microphone for ALL CALL paging over available speaker zones. • A maximum of 8 ECC-RMs(or combination of other remote display consoles).Conventional Fire Control PanelsFire-Lite’s 24-volt conventional fire alarm control panels (FACPs) bring the latest in microprocessor technology to conventional fire controls. With 2-zone, 4-zone, 5-zone, and 10-zone configurations, these units offeroptions to meet most local, state, and national requirements in the most efficient and effective way possible.MS-2• 2 initiating zones that are com- patible with 2- and 4-wire smoke detectors, 1 zone programmable for combo, supervisory, and waterflow.• 1 Notification Appliance Circuit (NAC) with built-in horn/strobe synchronization.• 3.0 amps maximum alarm current.MS-4• 4 initiating zones that are compatible with 2- and 4-wire smoke detectors, 1 zone programmable for combo, supervisory, and waterflow.• 2 Notification Appliance Circuits (NAC) with built-in horn/strobe synchronization.• Optional module converts all 4 initi- ating zones and 2 NACs to Class A.• 3.0 amps maximum alarm current expandable to 6.0 amps with optional second transformer.All Conventional Fire Control Panels Support System Sensor ®, Wheelock ®, Gentex ®, Faraday ®, and Amseco ® devices. MS-5UD• 5-zone Style B (Class B) or 5-zone Style D (Class A) with optional module.• 3.0 amps maximum alarm current.MS-10UD• 10-zone Style B (Class B) or 10-zone Style D (Class A) with 2 optional modules.• 7.0 amps maximum alarm current.MS-5UD/MS-10UD Shared Features and Specifications • 4 NAC Circuits Style Y (Class B) or 4 NACCircuits Style Z (Class A) with optional modules.• Built-in horn/strobe NAC synchronization with Remote Synchronization Output.• Integral 80-character LCD display with backlighting and keypad.• Annunciator bus supports up to 8 devices, including ANN-80 LCD Remote Annunciator, ANN-S/PG remote serial or parallel printer gateway, ANN-RLY , 10 form C relay board, ANN-LED Zone annunciator, and ANN-I/O LED driver board for graphic annunciators.• Built-in 2-line digital communicator for off-premises monitoring.•3 Form-C programmable relays.Synchronized Power SuppliesFire-Lite’s FCPS-24FS6 and FCPS-24FS8 are recognized as the benchmark for dependable fire alarm power supplies. Featuring built-in System Sensor ®, Wheelock ®, and Gentex ® strobe synchronization, these UL 9th Edition listed power devices can be cascaded with strobe timing maintained to meet any installation requirement.FCPS-24FS6 FCPS-24FS8• 24 volt, 6 or 8 amp versions available. • 4 Class B (Style Y)Class A (Style Z) outputs.• Built-in Strobe Synchronization for ADA Compliance. • Built-in 18 amp Hour Battery Charger.• Operates as a sync followeror a sync generator (default).ANN-I/OThe ANN-I/O is a LED driver module that can be used with a FACP to drive most customized graphic annunciators. It comes in a plastic enclosure that may be mounted inside a customannunciator or accessory cabinet, and can drive up to 40 LEDs.AnnunciatorsPull StationsBG-12 SeriesThe BG-12 is a cost-effective, non-coded series of fire alarm pull stations. They are available in both conventional and addressable versions, including single and dual action, with either key lock or hex key. The BG-12 series is typically specified and is a go-to for most architects and engineers.BG-8The BG-8 is a conven-tional, single-action metal fire alarm pull station for jurisdictionswhere metal pull stations are required.ANN-80 and ANN-100The ANN-80/100 are compact, backlit 80-character LCD fireannunciators. Both mimic the FACP display and provide system status indicators for AC, power, alarm, trouble, supervisory and alarm silence conditions. ANN-100 is FM and ULC approved.ANN-LEDThe ANN-LED annunciator module provides LED annunciation of general system faults, and input zones and points when used with a compatible FACP . It provides alarm, trouble, and supervisory indication for up to 10 input zones or addressablepoints.Addressable Smoke DetectionHWF2V-COM and HWF2A-COMThe HWF2V-COM (Verizon) and HWF2A-COM (AT&T) LTE fire alarm communicators represent a leading-edge internet and/or LTE cellular communications solution for moni-toring fire alarm systems and easily install using AlarmNet. Fast, secure, and effective alarm communications technology enables connection to any Contact-ID fire panel.HWF2V-COM (Verizon)IP/CellularCommunicatorsFire-Lite is always at the forefront of future detection code requirements.Our new line of addressable detectors, bases, and accessories maintain the same performance offered by previous core devices, now with a more modern look.SWIFT ®– Smart Wireless IntegratedFire TechnologySWIFT wireless addressable devices provide secure communication to the FACP across a Class A mesh network. SWIFT technology can be used in parallel with wired systems, allowing wirelessdevices to be added alongside wired devices on the same system.SWIFT GatewayUsing the W-GATE gateway, the FACP views SWIFT wirelessdevices as additional addressable devices on the system, providing similar detection functions and outputs as a wired counterpart.SWIFT DevicesThe SWIFT line offers a variety of device options including photoelectric, photo/thermal, fixed heat, and rate-of-rise heat detectors, pull stations, AV bases, and relay, monitor and sync modules.SWIFT ToolsEmploy a wireless transmitter (W-USB) to aid in the site survey, mesh formation, and diagnostics of the system.SD365COH365SD365HWF2A-COM (AT&T)ES-50XFire AlarmControl PanelExample of a Complete Fire Alarm System SD365Photo DetectorSD365COMulti-criteriaDetectorH365RMDF-300Dual MonitorModuleSD365TPhoto/ThermalDetectorMMF-300Monitor ModuleMMF-3022-Wire DetectorMonitor ModuleD355PLDuct DetectorBG-12LXPull Station OSI-RI-FL Beam DetectorMulti-Modules• CRF-300-6 Six-Relay Control Module • CMF-300-6 Six-Circuit Supervised • MMF-302-6 Six-Zone Interface Module • MMF-300-10 Ten Input Monitor Module • ISO-6 Six Output Isolator ModuleANN-100AnnunciatorECC-50/100Primary OperatorConsoleSPCWLSpeaker SPRLSpeakerSPSRLSpeaker/StrobeANN-80AnnunciatorS LC Lo o pECC-FFTFire Fighter TelephoneECC-50DAECC-50BDAECC-125DADistributed AudioAmplifiersECC-LOCLocal OperatorConsoleECC-RPURemote Paging UnitECC-RMRemote MicrophoneCDRM-300Dual Relay/MonitorModulePower SupplyFCPS-24FS6FCPS-24FS8P2RL StrobeW-GATEWirelessGatewayW-SD355Wireless Photo DetectorWAV-CRL with SCRLWirelessAV Base and StrobeW-H355WirelessHeat DetectorW-BG12LXWirelessPull StationW-MMFWirelessMonitor ModuleHWF2V-COMLTE Fire CommunicatorP2RL-LFHWL-LF Low Frequency Notification DevicesSWIFT® Wireless Mesh NetworkW-SYNCWirelessSync ModuleQuick Reference GuideFL_BR_ProductCatalog | Rev 03 | 09/2019 ©2019 Honeywell International, Inc.。
火灾报警控制器(联动型)使用说明书
JB-TG-ZH6300火灾报警控制器（联动型）安装使用说明书（Ver2007）（ZH2.900.082SS）安装前请阅读本说明书山东众海公共安全器材有限公司目录1 致用户...... .. (1)2概述 (2)3结构特征与工作原理 (4)3.1结构组成： (4)3.1.1报警及运行状态指示灯 (4)3.1.2操作键盘 (5)3.1.3液晶显示屏 (6)3.1.4多线制手动控制盘 (7)3.1.5内部结构布局。
(7)4系统操作使用及说明 (8)4.1页面概述 (8)4.2操作菜单的使用说明 (8)4.2.1信息查询 (8)4.2.2设备管理 (10)4.2.3系统管理 (10)4.2.4组态编程 (11)4.2.5帮助 (13)4.2.6报警信息页面 (13)4.2.7联动关系编程 (14)4.3常见警情和故障处理 (15)4.4使用前应注意的问题 (15)4.5故障分析与排除 (15)4.6维护、保养及储存 (16)4.7开箱检查及注意事项： (16)5附录（对使用的各种资源进行描述） (16)5.1附录1：常用名词解释 (16)5.2附录2：器件类型一览表 (17)5.3附录4：ZH6250多线制手动控制盘安装使用说明书 (18)5.4附录5：ZH6240总线制手动控制盘安装使用说明书 (20)5.5附录6：常用汉字机内码表 (23)1致用户……感谢您选用山东众海公共安全器材有限公司生产的火灾自动报警产品，它将在火灾预防和灭火控制方面发挥巨大作用，最大限度减小火灾灾害带来的损失，努力为您营造一个安全的生产生活空间。
山东众海公共安全器材有限公司是专业从事火灾自动报警设备的研发、生产、安装、和销售的公司。
公司的产品是由经验十分丰富的生产人员严格按照ISO9001质量管理体系的要求、特殊的工艺过程和严格的检验流程生产出来的，质量稳定可靠，能够满足防火防灾的严酷要求。
JB-TG-ZH6300火灾报警控制器（联动型）是我公司开发研制的新一代分布智能型产品，在产品使用前，请认真阅读本手册，它将指导您学习ZH6300火灾报警控制器（联动型）的使用方法。
报警主机使用说明书(中文版)
报警主机使用说明书(中文版)注意事项：1.安装场所远离高温的热源和环境，避免阳光直接照射。
为确保本机的正常散热，应避开通风不良的场所。
为了防止电击和失火，请勿将本机放置于易燃、易爆的场所。
小心轻放本机避免强烈碰撞、振动等，避免安装在会剧烈震动的场所。
MV2516智能报警主机避免在过冷、过热的场所间相互搬动本机，以免机器内部产生结露，影响机器的使用寿命。
（ALARM CONTROLLER）2.避免电击和失火使用说明书切记勿用湿手触摸电源开关和本机。
勿将液体溅落在本机上，以免造成机器内部短路或失火。
（中文版第一版）勿将其它设备直接放置于本机上部。
安装过程中进行接线或改线时，都应将电源断开，预防触电。
重要提示：为了避免损坏，请勿自动拆开机壳，必须委托有资格有专业维修人员在指定的维修单位进行维修。
清洁装置时,请勿使用强力清洗剂,当有灰尘时用干布擦拭装置。
不得在电源电压过高和过低的场合下使用该本机。
务请通读本使用说明书，以便您掌握如何正确使用本机。
当您读本说明书后，请把它妥善保存好，以备日后参考。
如果需要维修，请在当地与经本公司授权的维修站联系。
环境防护：本机符合国家电磁辐射标准，对人体无电磁辐射伤害。
申明：产品的发行和销售由原始购买者在许可协议条款下使用；未经允许，任何单位和个人不得将该产品全部或部分复制、再生或翻译深圳市智敏科技有限公司成其它机器可读形式的电子媒介；SHEN ZHEN ZHI MIN TECHNOLOGY CO.,LTD. 本手册若有任何修改恕不另行通知；Copyright 2000-2004. All Rights Reserved.因软件版本升级而造成的与本手册不符，以软件为准。
智能报警主机目 录ALARM CONTROLLER1.设备概述………………………………………………………………3 1.设备概述:2.设备介绍………………………………………………………………3 智能报警主机是采用微处理器控制的报警信息采集和输出设备。
消防报警主机操作规程(3篇)
第1篇一、概述消防报警主机是火灾自动报警系统的重要组成部分，负责接收、处理、显示火灾报警信号，并控制相关消防设备的启动。
为确保消防报警主机的正常运行和有效使用，特制定本操作规程。
二、操作人员要求1. 操作人员应经过专业培训，取得相应资格证书。
2. 操作人员应熟悉消防报警主机的结构、原理、性能及操作方法。
3. 操作人员应具备良好的职业道德，严格遵守消防安全法规和操作规程。
三、操作流程1. 开机操作（1）打开消防报警主机电源开关，确保主机供电正常。
（2）打开消防报警主机备电开关，为主机提供备用电源。
（3）等待主机上电初始化、自检、显示注册信息等过程完成后，进入正常监控状态。
2. 关机操作（1）关闭消防报警主机工作开关。
（2）关闭消防报警主机备电开关。
（3）关闭消防报警主机电源开关。
3. 火警处理（1）当主机接收到火警信号时，火警灯亮并发出警报声。
（2）操作人员应立即查看火警信号来源，确认火警位置。
（3）若为误报，操作人员应手动复位火警信号，消除警报。
（4）若为真实火警，操作人员应立即启动相关消防设备，组织人员疏散，并拨打119火警电话。
4. 故障处理（1）当主机出现故障时，故障灯亮。
（2）操作人员应立即查看故障信息，分析故障原因。
（3）若为线路故障，检查线路是否断线或短路，并进行修复。
（4）若为设备故障，通知生产厂方技术人员进行维修。
（5）故障排除后，重新启动主机，恢复正常监控状态。
四、注意事项1. 操作人员应定期对消防报警主机进行检查、维护，确保主机处于良好状态。
2. 操作人员应熟悉消防报警主机的各项功能，以便在紧急情况下迅速作出反应。
3. 操作人员应遵守消防安全法规和操作规程，确保消防报警主机安全、可靠运行。
4. 操作人员应做好消防报警主机的使用记录，以便跟踪、分析故障原因。
五、总结消防报警主机操作规程是确保火灾自动报警系统正常运行的重要保障。
操作人员应严格遵守本规程，不断提高自身业务水平，确保在火灾发生时能够迅速、有效地采取应急措施，保障人民生命财产安全。
网络报警主机使用说明书
LD988EQ火灾报警控制器_联动型_-调试手册
Y区
Z区
通信接口
CAN
USB
逻辑规则
联网
工作环境温度`
工作环境相对湿度
备用电池规格
最大外形尺寸
1.2 接线说明
JB-QB-LD988EQ
CAN 公共 公共 总线 火警 故障
技术参数 AC220(187～242V) 50Hz
DC 14V～24V DC26V/4A 8
2048（回路设备地址，不包括盘类的设备地址） 8（含 1 路声光警报输出） 214 200mA 65536 64 999 999 255 支持，波特率 10K 1 1024 支持总线拓扑结构。 0℃ ～ 45℃ ≤95%RH(40±2 ℃ ) 12V/14Ah 电池(两节)
LD-FJ/Y-337-02 TS
1
北京利达华信电子有限公司
LD988EQ 火灾报警控制器(联动型)工程调试手册
目录
版本：V1.0
第一章 简述 .......................................................................3
1.1 主要技术指标： ........................................................................ 3 1.2 接线说明 .............................................................................. 3
QD1+～QD7+和 QD1-～QD7-
七路有源输出端输出 24V 电源，QD+为 24V+，QD-为 24V-。如果现场没有接设 备，这两个端子上须并接 5.1K 终端电阻，不接电阻八路输出板相应路二极管灯 名明亮指示，如果在控制器中已经设置了该点的键值，控制器会报该点故障
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
安帝力消防报警主机ADL88说明书
一、电气火灾监控系统概述。
电气火灾监控系统是用于接收剩余电流式电气火灾探测器等现场设备信号，以实现对被保护电气线路的报警、监控、控制、管理的运算于计算机的硬件或软件系统。
二、电气火灾监控系统功能。
1、实时监测显示各节点的工作状态，故障（离线）、报警、实时测量值、通讯状态、电源工作状态等。
2、主机收到温度/漏电探测器报警后，警铃不会自动停止，必去人为消除。
3、主机自带2路总线防区，每路总线可以接99个总线制地址模块。
4、主机兼容普通报警主机功能，4个有线防区和16无线防区。
三、LED指示灯、按键。
1、指示灯说明
通讯指示：指示和中心联网的GPRS的状态。
主电故障：主机的220V电源没有接好，改灯闪烁。
备电故障：备用电池没有接好或者电池电压低，改灯亮。
系统故障：和主机连接的温度/漏电监测模块故障，该灯亮。
警笛短断续鸣叫，直到按下消除键消除。
报警：温度/漏电监测模块报警，该灯亮。
连续警笛鸣叫。
2、按键说明：
功能键：液晶屏菜单显示功能切换，每按一次主屏会在四个功能切换，“节点信息”“报警信息”“故障信息”“设置信息”。
消除键：报警或者故障信息清楚，同时关闭警铃声音。
上翻键：显示翻页。
下翻键：显示翻页。
确认键：屏幕返回主屏“节点信息”页面。