Distribution Box Bom
生产厂常用英文缩写
Education and Training教育训练proposal improvement/creative suggestion提案改善BS Brain Storming 脑力激荡QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结DCC delivery control center 交货管制中心3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品7SClassification整理(sorting, organization)-seiriRegulation整顿(arrangement, tidiness)-seitonCleanliness清扫(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教养(discipline)-shitsukeSave 节约Safety安全质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCT ools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门QC Section品管课administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板flat cable 排线resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈packaging tool打包机packaging打包品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理工厂常用缩略语５Ｓ：５Ｓ管理ＡＢＣ：作业制成本制度(Activity-Based Costing)ＡＢＢ：实施作业制预算制度(Activity-Based Budgeting)ＡＢＭ：作业制成本管理(Activity-Base Management)ＡＰＳ：先进规画与排程系统(Advanced Planning and Scheduling) ＡＳＰ：应用程序服务供货商（Application Service Provider）ＡＴＰ：可承诺量(Available To Promise)ＢＯＭ：物料清单(Bill Of Material)ＢＰＲ：企业流程再造(Business Process Reengineering)ＢＳＣ：平衡记分卡(Balanced ScoreCard)ＢＴＦ：计划生产(Build To Forecast)ＢＴＯ：订单生产(Build To Order)ＣＰＭ：要径法(Critical Path Method)ＣＲＭ：客户关系管理(Customer Relationship Management)ＣＲＰ：产能需求规划(Capacity Requirements Planning)ＣＴＯ：客制化生产(Configuration To Order)ＤＢＲ：限制驱导式排程法(Drum-Buffer-Rope)ＤＲＰ：运销资源计划(Distribution Resource Planning)ＤＳＳ：决策支持系统(Decision Support System)ＥＣ：设计变更／工程变更(Engineer Change)ＥＣ：电子商务(Electronic Commerce)ＥＤＩ：电子资料交换(Electronic Data Interchange)ＥＩＳ：主管决策系统(Excutive Information System)ＥＯＱ：基本经济订购量(Economic Order Quantity)ＥＲＰ：企业资源规划(Enterprise Resource Planning)ＦＭＳ：弹性制造系统(Flexible Manufacture System)ＦＱＣ：成品品质管制(Finish or Final Quality Control)ＩＰＱＣ：制程品质管制(In-Process Quality Control)ＩＱＣ：进料品质管制(Incoming Quality Control)ＪＩＴ：实时管理(Just In Time)ＫＭ：知识管理(Knowledge Management)Ｌ４Ｌ：逐批订购法(Lot-for-Lot)ＬＴＣ：最小总成本法(Least Total Cost)ＬＵＣ：最小单位成本(Least Unit Cost)ＭＥＳ：制造执行系统(Manufacturing Execution System)ＭＰＳ：主生产排程(Master Production Schedule)ＭＲＰ：物料需求规划(Material Requirement Planning)ＭＲＰⅡ：制造资源计划(Manufacturing Resource Planning)ＯＥＭ：委托代工(Original Equipment Manufacture)ＯＤＭ：委托设计与制造(Original Design & Manufacture)ＯＬＡＰ：线上分析处理(On-Line Analytical Processing)ＯＬＴＰ：线上交易处理(On-Line Transaction Processing)ＯＰＴ：最佳生产技术(Optimized Production Technology)ＯＱＣ：出货品质管制(Out-going Quality Control)ＰＤＣＡ：PDCA管理循环(Plan-Do-Check-Action)ＰＤＭ：产品数据管理系统(Product Data Management)ＰＥＲＴ：计画评核术(Program Evaluation and Review Technique) ＰＯＨ：预估在手量(Project on Hand)ＱＣＣ：品管圈(Quality Control Circle)ＲＣＣＰ：粗略产能规划(Rough Cut Capacity Planning)ＲＯＰ：再订购点(Re-Order Point)ＳＣＭ：供应链管理(Supply Chain Management)ＳＦＣ：现场控制(Shop Floor Control)ＳＩＳ：策略信息系统(Strategic Information System)ＳＰＣ：统计制程管制(Statistic Process Control)ＴＯＣ：限制理论(Theory of Constraints)ＴＱＣ：全面品质管制(Total Quality Control)ＴＱＭ：全面品质管理(Total Quality Management)ＷＩＰ：在制品(Work In Process)>>> ５Ｓ：５Ｓ管理5S是由JP企业研究出来的一种环境塑造方案，其目的在藉由整理(SEIRI)、整顿(SEITON)、清扫(SEISO)、清洁(SEIKETSU)及身美(SHITSUKE)五种行为来创造清洁、明朗、活泼化之环境，以提高效率、品质及顾客满意度。
(工厂管理)工厂常用英文
部分工厂常用英文,供大家参考.Education and Training教育训练proposal improvement/creative suggestion提案改善BS Brain Storming 脑力激荡QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结DCC delivery control center 交货管制中心3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品7SClassification整理(sorting, organization)-seiri Regulation整顿(arrangement, tidiness)-seiton Cleanliness清扫(sweeping, purity)-seiso Conservation清洁(cleaning, cleanliness)-seiktsu Culture教养(discipline)-shitsukeSave 节约Safety安全质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门QC Section品管课administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板flat cable 排线resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈packaging tool打包机packaging打包品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理工厂常用缩略语５Ｓ：５Ｓ管理ＡＢＣ：作业制成本制度(Activity-Based Costing)ＡＢＢ：实施作业制预算制度(Activity-Based Budgeting)ＡＢＭ：作业制成本管理(Activity-Base Management)ＡＰＳ：先进规画与排程系统(Advanced Planning and Scheduling) ＡＳＰ：应用程序服务供货商（Application Service Provider）ＡＴＰ：可承诺量(Available To Promise)ＢＯＭ：物料清单(Bill Of Material)ＢＰＲ：企业流程再造(Business Process Reengineering)ＢＳＣ：平衡记分卡(Balanced ScoreCard)ＢＴＦ：计划生产(Build To Forecast)ＢＴＯ：订单生产(Build To Order)ＣＰＭ：要径法(Critical Path Method)ＣＲＭ：客户关系管理(Customer Relationship Management) ＣＲＰ：产能需求规划(Capacity Requirements Planning)ＣＴＯ：客制化生产(Configuration To Order)ＤＢＲ：限制驱导式排程法(Drum-Buffer-Rope)ＤＲＰ：运销资源计划(Distribution Resource Planning)ＤＳＳ：决策支持系统(Decision Support System)ＥＣ：设计变更／工程变更(Engineer Change)ＥＣ：电子商务(Electronic Commerce)ＥＤＩ：电子资料交换(Electronic Data Interchange)ＥＩＳ：主管决策系统(Excutive Information System)ＥＯＱ：基本经济订购量(Economic Order Quantity)ＥＲＰ：企业资源规划(Enterprise Resource Planning)ＦＭＳ：弹性制造系统(Flexible Manufacture System)ＦＱＣ：成品品质管制(Finish or Final Quality Control)ＩＰＱＣ：制程品质管制(In-Process Quality Control)ＩＱＣ：进料品质管制(Incoming Quality Control)ＪＩＴ：实时管理(Just In Time)ＫＭ：知识管理(Knowledge Management)Ｌ４Ｌ：逐批订购法(Lot-for-Lot)ＬＴＣ：最小总成本法(Least Total Cost)ＬＵＣ：最小单位成本(Least Unit Cost)ＭＥＳ：制造执行系统(Manufacturing Execution System)ＭＰＳ：主生产排程(Master Production Schedule)ＭＲＰ：物料需求规划(Material Requirement Planning)ＭＲＰⅡ：制造资源计划(Manufacturing Resource Planning)ＯＥＭ：委托代工(Original Equipment Manufacture)ＯＤＭ：委托设计与制造(Original Design & Manufacture)ＯＬＡＰ：线上分析处理(On-Line Analytical Processing)ＯＬＴＰ：线上交易处理(On-Line Transaction Processing)ＯＰＴ：最佳生产技术(Optimized Production Technology)ＯＱＣ：出货品质管制(Out-going Quality Control)ＰＤＣＡ：PDCA管理循环(Plan-Do-Check-Action)ＰＤＭ：产品数据管理系统(Product Data Management)ＰＥＲＴ：计画评核术(Program Evaluation and Review Technique)ＰＯＨ：预估在手量(Project on Hand)ＱＣＣ：品管圈(Quality Control Circle)ＲＣＣＰ：粗略产能规划(Rough Cut Capacity Planning)ＲＯＰ：再订购点(Re-Order Point)ＳＣＭ：供应链管理(Supply Chain Management)ＳＦＣ：现场控制(Shop Floor Control)ＳＩＳ：策略信息系统(Strategic Information System)ＳＰＣ：统计制程管制(Statistic Process Control)ＴＯＣ：限制理论(Theory of Constraints)ＴＱＣ：全面品质管制(Total Quality Control)ＴＱＭ：全面品质管理(Total Quality Management)ＷＩＰ：在制品(Work In Process)> ５Ｓ：５Ｓ管理5S是由JP企业研究出来的一种环境塑造方案，其目的在藉由整理(SEIRI)、整顿(SEITON)、清扫(SEISO)、清洁(SEIKETSU)及身美(SHITSUKE)五种行为来创造清洁、明朗、活泼化之环境，以提高效率、品质及顾客满意度。
电子企业常用英语术语
电子公司常用英语术语一:常用术语CMM Component module move 机动组件整合CEM Contract Manufaction service 合约委托代工IBSC Internet Business Solution Center 国际互联网应用中心PCEG Personal Computer Enclosure group 个人计算机外设事业群（FOXTEQ）CCBG Connector&cable business groupCPBG Competition business groupESBG Enterprise system business group 鸿富锦事业群SABG system assembly business group 系统组装事业群NWE Net Work EnclosureNSE Network system enclosureNSG Network system groupNFE Network flexible enclosureFoxcavity = HZ = Hong Zhun 鸿准Stamping tool shop I 冲模一厂Stamping tool shop II 冲模二厂Prototype workshop 样品中心Steel factory 裁剪厂PCE molding tooling workshop PCE塑模厂Hua Nan test and measurement center 华南检测中心MPE mobile phone enclosure MPEMBE mobile phone and notebook enclosure 明塑厂MGE Alloy magnesium alloy enclosure 镁合金Engineer standard 工标Document center (database center)数据中心Design Center 设计中心Painting 烤漆(厂) Assembly组装(厂)Stamping 冲压(厂)Education and Training教育训练proposal improvement/creative suggestion提案改善Technological exchange and study 技术交流研习会Technology and Development Committee 技术发展委员会BS Brain Storming 脑力激荡QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结DCC delivery control center 交货管制中心3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品Core value（核心价值）Love 爱心Confidence 信心Decision 决心Corporate culture(公司文化)Integration 融合Responsibility 责任Progress 进步3T STRATEGYTime to market 及时切入生产Time to volume 及时大量生产Time to money 及时大量交货FOUR CONTROL YSTEM 四大管制系统Engineering control system 工程管制系统Quality control system质量管理系统Manufacturing control system生产管制系统Management control system经营管制系统7SClassification整理(sorting, organization)-seiri Regulation整顿(arrangement, tidiness)-seiton Cleanliness清扫(sweeping, purity)-seiso Conservation清洁(cleaning, cleanliness)-seiktsu Culture教养(discipline)-shitsukeSave 节约Safety安全二:英文缩写质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 数据中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)标识符SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱) DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessA VL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti|=vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department 人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventorysecond count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventorylist备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard外观检验规范computer case 计算机外壳(组件)personal computer enclosure计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 扁平电缆TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/accepted parts/good parts良品defective product/non-goodparts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gas ket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button 圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece,location block定位块reset复位to file burr 锉毛刺embedded lump |in'bed| |l mp|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸) draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印extension DWG展开图procedure DWG工程图die structure DWG模具结构图冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口runner less无浇道sprue less 无射料管方式long nozzle延长喷嘴方式spur浇口;溶waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for准备rotating speed, revolution转速abnormal handling异常处理组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to senddelivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴品质类qualified products, up-to-grade products良品defective products, notup-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure 制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕。
物流专业英语单词
物流专业单词1．物品article2．物流logistics3．物流活动logistics activity4．物流作业logistics operation5．物流模数logistics modulus6．物流技术logistics technology 7．物流成本logistics cost8．物流管理logistics management 9．物流中心logistics center10．物流网络logistics network 11．物流信息logistics information 12．物流企业logistics enterprise 13．物流单证logistics documents 14．物流联盟logistics alliance 15．供应物流supply logistics16．生产物流production logistics 17．销售物流distribution logistics 18．回收物流returned logistics 19．废弃物物流waste material logistics 20．绿色物流environmental logistics 21．企业物流internal logistics 22．社会物流external logistics 23．军事物流military logistics24．国际物流international logistics25．第三方物流third-part logistics (TPL)26．定制物流customized logistics27．虚拟物流virtual logistics28．增值物流服务value-added logistics service 29．供应链supply chain30．条码bar code31．电子数据交换electronic data interchange (EDI) 32．有形消耗tangible loss33．无形消耗intangible loss 奖罚物流作业术语1．运输transportation2．联合运输combined transport3．直达运输through transport4．中转运输transfer transport5．甩挂运输drop and pull transport6．集装运输containerized transport7．集装箱运输container transport8．门到门door-to-door9．整箱货full container load (FCL)10．拼箱货less than container load (LCL11．储存storing12．保管storage13．物品储存article reserves14．库存inventory15．经常库存cycle stock16．安全库存safety stick17．库存周期inventory cycle time 18．前置期（或提前期）lead time 19．订货处理周期order cycle time 20．货垛goods stack21．堆码stacking22．搬运handing/carrying23．装卸loading and unloading24．单元装卸unit loading and unloading 25．包装package/packaging26．销售包装sales package27．定牌包装packing of nominated brand 28．中性包装neutral packing29．运输包装transport package30．托盘包装palletizing31．集装化containerization32．散装化containerization33．直接换装cross docking34．配送distribution35．共同配送joint distribution36．配送中心distribution center37．分拣sorting38．拣选order picking39．集货goods collection40．组配assembly41．流通加工distribution processing42．冷链cold chain43．检验inspection 奖罚物流技术装备及设施术语1．仓库warehouse2．库房storehouse3．自动化仓库automatic warehouse 4．4立体仓库stereoscopic warehouse5．虚拟仓库virtual warehouse6．保税仓库boned warehouse7．出口监管仓库export supervised warehouse8．海关监管货物cargo un der customer’s supervision 9．冷藏区chill space10．冷冻区freeze space11．控湿储存区humidity controlled space12．温度可控区temperature controlled space 13．收货区receiving space14．发货区shipping space15．料棚goods shed16．货场goods yard17．货架goods shelf18．托盘pallet19．*车fork lift truck20．输送机conveyor21．自动导引车automatic guided vehicle (AGV)22．箱式车box car23．集装箱container24．换算箱twenty-feet equivalent unit (TEU)25．特种货物集装箱specific cargo container26．全集装箱船full container ship27．铁路集装箱场railway container yard28．公路集装箱中转站inland container depot29．集装箱货运站container freight station (CFS)30．集装箱码头container terminal31．国际铁路联运international through railway transport32．国际多式联运international multimodal transport33．大陆桥运输land bridge transport34．班轮运输liner transport35．租船运输shipping by chartering36．船务代理shipping agency37．国际货运代理international freight forwarding agent38．理货tally39．国际货物运输保险international transportation cargo insurance 40．报关customs declaration41．报关行customs broker42．进出口商品检验commodity inspection 奖罚物流管理术语1．物流战略logistics strategy2．物流战略管理logistics strategy management3．仓库管理warehouse management4．仓库布局warehouse layout5．库存控制inventory control6．经济订货批量economic order quantity (EOQ)7．定量订货方式fixed-quantity system (FQS)8．定期订货方式fixed-quantity system (FIS)9．ABC分类管理ABC classification10．电子订货系统Electronic order system (EOS)11．准时制just in time (JIT)12．准时制物流just-in-time logistics13．零库存技术zero-inventory logistics14．物流成本管理logistics cost control15．物料需要计划material requirements planning (MRP)16．制造资源计划manufacturing resource planning (MRP II) 17．配送需要计划distribution requirements planning (DRP) 18．配送资源计划distribution resource planning (DRP II) 19．物流资源计划logistics resource planning (LRP)20．企业资源计划enterprise resource planning (ERP)21．供应链管理supply chain management (SCM)22．快速反映Quick response (QR)23．有效客户反映efficient customer response(ECR)24．连续库存补充计划continuous replenishment program (CRP)25．计算机付诸订货系统computer assisted ordering (CAO) 26．供应商管理库存vendor managed inventory (VMI)27．业务外包outsourcing物流中级英语（共145个）基本概念术语1．物品article 2．物流logistics 3．物流活动logistics activity 4．物流作业logistics operation 5．物流模数logistics modulus 6．物流技术logistics technology 7．物流成本logistics cost 8．物流管理logistics management 9．物流中心logistics center 10．物流网络logistics network 11．物流信息logistics information 12．物流企业logistics enterprise 13．物流单证logistics documents 14．物流联盟logistics alliance 15．供应物流supply logistics 16．生产物流production logistics 17．销售物流distribution logistics 18．回收物流returned logistics 19．废弃物物流waste material logistics 20．绿色物流environmental logistics 21．企业物流internal logistics 22．社会物流external logistics 23．军事物流military logistics 24．国际物流international logistics 25．第三方物流third-part logistics (TPL) 26．定制物流customized logistics 27．虚拟物流virtual logistics 28．增值物流服务value-added logistics service 29．供应链supply chain 30．条码bar code 31．电子数据交换electronic data interchange (EDI) 32．有形消耗tangible loss 33．无形消耗intangible loss 奖罚物流作业术语1．运输transportation 2．联合运输combined transport 3．直达运输through transport 4．中转运输transfer transport 5．甩挂运输drop and pull transport 6．集装运输containerized transport 7．集装箱运输container transport 8．门到门door-to-door 9．整箱货full container load (FCL) 10．拼箱货less than container load (LCL 11．储存storing 12．保管storage 13．物品储存article reserves 14．库存inventory 15．经常库存cycle stock 16．安全库存safety stick17．库存周期inventory cycle time 18．前置期（或提前期）lead time 19．订货处理周期order cycle time 20．货垛goods stack 21．堆码stacking 22．搬运handing/carrying 23．装卸loading and unloading 24．单元装卸unit loading and unloading 25．包装package/packaging 26．销售包装sales package 27．定牌包装packing of nominated brand 28．中性包装neutral packing 29．运输包装transport package 30．托盘包装palletizing 31．集装化containerization 32．散装化containerization 33．直接换装cross docking 34．配送distribution 35．共同配送joint distribution 36．配送中心distribution center 37．分拣sorting 38．拣选order picking 39．集货goods collection 40．组配assembly 41．流通加工distribution processing 42．冷链cold chain 43．检验inspection 奖罚物流技术装备及设施术语1．仓库warehouse 2．库房storehouse 3．自动化仓库automatic warehouse 4．4立体仓库stereoscopic warehouse 5．虚拟仓库virtual warehouse 6．保税仓库boned warehouse 7．出口监管仓库export supervised warehouse 8．海关监管货物cargo under customer’s supervision 9．冷藏区chill space 10．冷冻区freeze space 11．控湿储存区humidity controlled space 12．温度可控区temperature controlled space 13．收货区receiving space 14．发货区shipping space 15．料棚goods shed 16．货场goods yard 17．货架goods shelf 18．托盘pallet 19．叉车fork lift truck 20．输送机conveyor 21．自动导引车automatic guided vehicle (AGV) 22．箱式车box car 23．集装箱container 24．换算箱twenty-feet equivalent unit (TEU) 25．特种货物集装箱specific cargo container 26．全集装箱船full container ship 27．铁路集装箱场railway container yard 28．公路集装箱中转站inland container depot 29．集装箱货运站container freight station (CFS) 30．集装箱码头container terminal 31．国际铁路联运international through railway transport 32．国际多式联运international multimodal transport 33．大陆桥运输land bridge transport 34．班轮运输liner transport 35．租船运输shipping by chartering 36．船务代理shipping agency 37．国际货运代理international freight forwarding agent 38．理货tally 39．国际货物运输保险international transportation cargo insurance 40．报关customs declaration 41．报关行customs broker42．进出口商品检验commodity inspection 奖罚物流管理术语1．物流战略logistics strategy 2．物流战略管理logistics strategy management 3．仓库管理warehouse management 4．仓库布局warehouse layout 5．库存控制inventory control 6．经济订货批量economic order quantity (EOQ) 7．定量订货方式fixed-quantity system (FQS) 8．定期订货方式fixed-quantity system (FIS) 9．ABC分类管理ABC classification 10．电子订货系统Electronic order system (EOS) 11．准时制just in time (JIT) 12．准时制物流just-in-time logistics 13．零库存技术zero-inventory logistics 14．物流成本管理logistics cost control 15．物料需要计划material requirements planning (MRP) 16．制造资源计划manufacturing resource planning (MRP II) 17．配送需要计划distribution requirements planning (DRP) 18．配送资源计划distribution resource planning (DRP II) 19．物流资源计划logistics resource planning (LRP) 20．企业资源计划enterprise resource planning (ERP) 21．供应链管理supply chain management (SCM) 22．快速反映Quick response (QR) 23．有效客户反映efficient customer response(ECR) 24．连续库存补充计划continuous replenishment program (CRP) 25．计算机付诸订货系统computer assisted ordering (CAO) 26．供应商管理库存vendor managed inventory (VMI) 27．业务外包outsourcingAabc classificiation abc分类法.A Circular Letter 通告信/通知书Accomplish a Bill of Lading (to) 付单提货acquisition cost ordering cost 定货费Act of God 天灾activity cost pool 作业成本集activity-based costing 作业基准成本法Actual Displacement 实际排水量Ad valorem freight 从价运费Addendum (to a charter party) ( 租船合同)附件Additional for Alteration of Destination 变更卸货港附加费Additional for Optional Destination 选卸港附加费Address commission (Addcomm) 回扣佣金Adjustment 海损理算Advanced B/L 预借提单advanced shipping notice (asn) 预先发货通知A fixed day sailing 定日航班A fortnight sailing 双周班A Friday（Tuesday / Thursday）sailing 周五班agile manufacturing 敏捷制造Air Express 航空快递airline operator/freight forwarder 不营运船舶的多式联运经营人Air Waybill 航空运单Alliance 联盟All in rate 总运费率All purposes (A.P) 全部装卸时间All time saved (a.t.s) 节省的全部时间allocation―――中转？Always afloat 始终保持浮泊American Bureau of Shipping (A.B.S.) 美国船级社A monthly sailing 每月班AMT (Advanced Manufacturing Technology) 先进制造技术Anchorage 锚地Anchorage dues 锚泊费Annual survey 年度检验anticipation inventory 预期储备Anti-dated B/L 倒签提单APICS (American Production and Inventory Control Society,Inc.) 美国生产与库存管理系统Applied Manufacturing Education Series 实用制造管理系列培训教材Apron 码头前沿Arbitration award 仲裁裁决Arbitrator 仲裁员Area differential 地区差价Arrest a ship 扣押船舶AS/RS (automated storage/retrieval system) 自动化仓储系统assemble-to-order 定货组装assembly 组配Article reserves物品储备ATP (available to promise) 可供销售量automatic replenishment (ar) 自动补货系统automatic warehouse 自动化仓库Automatic guided vehicle （AGV）自动导引车automated high-rise warehouse 自动立体仓库Average adjuster 海损理算师Average bond 海损分摊担保书Average guarantee 海损担保书A weekly sailing 周班axle housing桥壳Axle load 轴负荷Bbackflushing 反冲法Backfreight 回程运费back-hauls―――回程空载Back (return) load 回程货backlog 拖欠定单back order 脱期定单, 延期交货成本（back order costs）。
常用化工机械专业英语对照
常用机械专业英语对照Cutting: 切割socket weld 承插焊接fillet weld 角焊 ,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder 馈电线conduit outlet 电线引出口seal fitting 密封接头 , 密封配件Screw thread lubricant螺纹润滑剂 Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧 [ 止动 , 防松 ]垫圈 electrical panel.配电板 ,配电盘nipple 螺纹接头zinc plated.镀锌的ring joint 环接 , 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程 master schedule 主要图表 , 综合图表 , 设计任务书 , 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接 Hard hat：安全帽Goggles：护目镜stockpile 贮存packing list 装箱单crate: 柳条箱purchased material list原材料进货单 back-feed 反馈wire coil 线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block 线弧 , 接头排接线盒 , 接线板 , 线夹power drill 机械钻connector. 接线器insulated sleeve绝缘套管wire connector 接线器wire terminal 电线接头motor lead 电动机引出线power wiring 电力布线tender document．提供证件 orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld 加强焊缝fabrication.制造dye penetrant examination染料渗透试验法 magnetic particle examination 磁粉检验 girth weld 环形焊缝cement lined piping 水泥衬里weld joint 焊缝 , 焊接接头 spool drawing 管路图 , 管路详图 spottest 抽查 , 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly装.配erection 架设examination 试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable 控制电缆操纵索normal bend 法向 [ 法线 ]弯管cable glands: 电缆衬垫exfoliation 剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture 照明器材junction box 分线箱 race way电缆管道terminal box 接线盒distribution board 配电盘 , 配电屏receptacle 插座tumble switch.翻转开关 ,拨动式开关cathodic protection system 阴极保护系统 Circuit breaker 断路开关amplifier panel 放大器盘 control console 控制台 electricalmaterial 电气材料 convenience receptacle电.源插座 cableTIG ： Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod 焊条tensile strength 抗张强度shield gas 保护气体shield jig 保护夹具high frequency generator高.频发电机 welding rod 焊条filler metal 焊料 , 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal. 纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination非.破坏性检验 , qualification: 合格性construction work 施工工程welded joint 焊接缝焊接节点gas cutting.气割arc cutting 电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验 Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment ：对准 ,定位调整check against 检查 , 核对Fixing ：固定Console：控制台cubicle 室,箱audit 审计material certificate.材料合格证vertical panel 竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱 ,磨斜边local panel 现场配电盘fabrication 加工 ,制造instrument rack 计测器支架tank gauge 液面计 flushing冲洗，填缝 analyzer 分析器piping 管道敷设tubing 敷设管道cable fitting 电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理 jig. 夹具arc gouging 电弧刨削chipping 修琢machining 机械加工bridges.管式桥clamp.夹钳压力容器基本词汇安全阀safety valve安装 Installation鞍式支座saddle support凹面 concave半球形封头Hemispherical heads 棒bars保温支撑 insulation support [wiki] 爆炸 [/wiki] 性 explosive泵pump变径段 reducers标记 stamping标志 marking标志的移植 Transferring marking 波纹板 Corrugating Paper补强管reinforcing nozzle补强圈reinforcing ring不锈钢stainless steel不圆度out-of-roundness材料 materials材料证明书 Certification of material 超声检验 Ultrasonic Examination 衬里 Linings成型 Forming成型封头Formed heads尺寸 Dimensions翅片管finned tubes冲击试验impact test传热面积heat transfer surface磁粉检验Magnetic Particle Examination次要应力secondary stress粗糙度 roughness淬火 Quenching带折边的锥形toriconical弹簧 springs弹簧垫圈spring washer弹性模量modulus of Elasticity挡板 baffle plate低合金钢容器low alloy steel vessels低温容器Low-temperature vessels地震烈度seismic intensity垫板 Backing strip垫片 gasket垫圈 washer碟形封头Dished heads顶丝 jackscrew定距管 spacer定位销 pin dowel定义 Definitions毒性 toxicity镀锌容器Galvanized vessels锻件 Forgings对焊 [wiki] 法兰 [/wiki] welding neck flange耳座 lug[wiki] 阀门 [/wiki] valves法兰 flanges法兰接触面Flange contact facings防冲板 impingement baffle防 [wiki] 腐蚀 [/wiki] 衬里Corrosion resistant linings防火 fire protection防涡流挡板vortex breaker非受压件nonpressure parts非圆形容器Noncircular vessels分析 analysis峰值应力peak stress腐蚀裕量corrosion allowance附加载荷supplementary loading附件 attachments复合板 Clad plate覆层容器clad vessels盖板 Cover plates杆 rods and bars刚性 Stiffness高合金容器high-alloy vessels 工作压力operation pressure固定的fixed管板 tube sheet管壳式换热器shell and tube heat exchanger 管口材料表sheet of material for nozzle管口方位nozzle orientation管箱 channel管子 pipes nozzle tube管嘴 nipple罐桶槽 tank过渡段transition in过渡圆角Knuckles焊后热处理after post weld heat treating焊接工艺welding procedure specification焊接接头welding joints焊接系数welding coefficient厚度 thickness滑动的sliding环向应力hoop stress回火 tempering基本地震加速度basic seismic acceleration 基本分压basic wind pressure计算厚度calculated thickness技术条件form of Specification加强圈stiffening rings夹套容器Jacketed vessels检查孔Inspection openings检验 inspection角焊 Fillet welds接地板earth lug截止阀Stop valves介质特性fluid property金属温度Metal temperature筋板 rib plate径向应力radial stress静(压力 )水头 static head局部 areas局部 local局部焊后热处理Local postweld heat treatment矩形设计rectangular design卡箍 clamp开孔补强reinforcement for openings快开盖Quick-actuating closures拉杆 tie rod裂缝 Cracking流体（介质）fluid螺母 nut螺塞 plug螺栓 bolt螺纹 threaded螺柱 studs名义厚度 nominal thickness铭牌 Nameplates内部构件 Internal structures内衬筒 internal shell盘管 coil tube配件 fittings膨胀节 expansion joint平封头 Flat heads评定 Qualification气孔 Porosity气压试验Pneumatic test钎焊 brazing强度 strength of球形封头 spherically dished曲率 curvature屈服 yielding全容积 total volume缺陷 defects群座 skirt support热处理 thermal treatment热处理 heat treatmen热应力 thermal stress人孔 manholes韧性 ductility容积 volume容器 vessel容器净重empty weight容器类别 vessel classification塞焊 Plug welds设计压力design pressure射线超声检验 Radiographic Examination 渗透检验 Penetrant Examination 石墨graphite试样 Test coupons适用范围Scope手孔 handholes水压试验 hydrostatic test/hydraulic test/hydrotest碳钢 carbon steel搪玻璃容器enameled vessels梯子、平台ladders, platforms填充金属 filler metal 凸面 convex凸缘 socket椭圆封头Ellipsoidal heads外压容器 vessels subjected to external pressure未注尺寸公差tolerance grade not noted 无支撑unstayed系数 factor现场安装Field assembly校核 checking of泄放 Discharge泄压装置 Pressure relieving devices性能 properties许用工作压力 allowable working pressure 许用应力 allowable stress 易然的flammable应力腐蚀stress corrosion应力集中 stress concentration预热 Preheating圆度 roundness圆角和倒角 corners and fillets载荷 Loadings胀接 expanded connections折流板 baffle plate蒸发器Evaporators直边长度length of skirt直径 Diameter制造 fabrication制造厂fabricator制造方法methods of fabrication制造工艺fabrication technology周长 Girth主应力primary stress柱状壳体 Cylindrical shells铸铁容器 cast iron vessels转角半径 knuckle radius 装配 assembling 锥度tapered锥壳 conical shell锥形封头Conical heads资格 qualification纵向接头 Longitudinal joints组对 fitting uppipe closure 管塞 end closure端盖 orifice plate 挡板 exialspacing 轴向间距 manufacturetolerance 制造公差acid passivation 酸洗钝化part drawing 零件图stud bolts 双头螺柱化工设备常用词汇和缩写中英文对照化工设备常用词汇和缩写中英文对照缩写 / 英文 /中文AB Anchor Bolt地脚螺栓Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure大气压 Auto Automatic 自动Aux Auxiliary辅助设备、辅助的Avail Available 有效的、可用的Avg Average 平均AW Arc welding 电弧焊AW Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规AWS(AWI) American WeldingSociety(Institute) 美国焊接学会 BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距 BC Bolt circle 螺栓中心圆BD Blow down放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求 BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly Valve碟阀BW Brine Vater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本 cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化 Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost， Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure压力中心 Cpl Coupling 管箍 CplgCoupling 联轴节CR Chloroprene Rubber 氯丁橡胶 CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒D Density 密度Dbl Double 二倍、双DEDD Detail Engineering Design Data 详细工程设计数据Def Definition定义Deg Degree 度、等级Dept Department 部门Des Design 设计Det Detail 详细Detn Determination 确定、决定Dev Deviation 偏差Dev Device 装置DF Design Formula 设计公式Df Deflection 偏斜Dia Diameter 直径Diag Diagram 图Dim Dimension 尺寸Dir Direction方向Disch Discharge 排出、出口Distr Distribution 分布Div Division 部分、区分 DLDoc Document 文件、资料DP Design Pressure 设计压力DP Differential Pressure 压差、分压Dr Drill 钻孔Dr Drive 驱动DW Dead weight 静重、自重DW Demineralized Water 脱盐水Dwg Drawing 图 E East 东EC Elasticity Coefficient 弹性系数Ecc Eccentric 偏心EF Electric Furnace 电炉Eff Efficiency效率eg exempli gratia 例如EHP Effective Horsepower 有效功率EJ Expansion joint 膨胀节EL Elevation 标高Elb Elbow 弯头Elec Electric 电的Elem Element 元素、元件Ellip Ellipsoidal椭球的、椭圆的Emer、 Emerg Emergency 事故、紧急Encl Enclosure 密封、封闭Engrg、Eng Engineering 工程、设计EP Explosion Proof 防爆Eq Equipment 设备Eq Equation 公式、方程式Eq Equivalent 当量ES Electrostatic 静电EST Estimate 估计ESW Electro-Slag Welding 电渣焊ET Eddy Current Examination 涡流检验etc et cetera (and so on)等等Evap Evaporate 蒸发Ex Example 例如Ex Excess 过剩、超过Exam Examination 检验Exh Exhaust 废气、排气Exp Expansion 膨胀Exptl Experimental 实验的Ext External 外部Ext Extreme 极端的FAO Finish All Over 全部加工FAX Facsimile 传真FB Flat Bar 扁钢FCAW Flux Cored Arc Welding 熔剂芯弧焊（手工焊）FDW Feed Water 给水FF Flat Face 平面F/F Field Fabricated 现场制造Fig Figure 图Fin Finish 加工、完成FL Full Load 满载Flex Flexible 挠性Flg Flange 法兰FOB Free On Board 离岸价格FOC Free Of Charge 免费Forg Forging 锻件FOS Factor Of Safety 安全系数FREQ Frequency 频率FST Forged Steel 锻钢Ft Feet 英尺Ftg Fitting 管件、装配F.V. Full Vacuum 全真空FW Fresh Water 新鲜水FW Field Weld 现场焊接FW Fillet Weld 角焊缝GA General Average 平均值Gal Gallon 加仑Gen General 一般、总的Genr Generator 发电机、发生器 GF Groove Face 槽面Gl Glass 玻璃GL Ground Level 地面标高GMAW Gas Metal Arc Welding 气体保护金属极电弧焊Gnd Ground 接地、地面Govt Government 政府GP General Purpose一般用途、通用 Gr Grade 等级Gr Gravity 重力Grd Ground 地面Grp Group 分组、类Gr- wt Gross weight 总重、毛重HB Brinell Hardness 布氏硬度HC Hydrocarbon 烃类HC High Capacity 大容量HD Head 压头Hex Hexagon 六角HH Hand Hole 手孔Hor Horizontal 水平、卧式hp Horsepower 马力HP High Pressure 高压HR Rockwell Hardness 洛氏硬度HRC Rockwell C Hardness C 级洛氏硬度 HS High Pressure Steam高压蒸汽HS Shore Scleroscope Hardness肖氏硬度HSC High Pressure Condensate 高压蒸汽凝液HT High Temperature 高温HT Heat Treatment 热处理HT Hydrostatic Test 水压试验HV Vickers Hardness 维氏硬度Hvy Heavy 重的、重型的HW Hot Water 热水ICW Inter Cooling Water 中间冷却水ID Inside Diameter 内径IF Interface 交接面Illus Illustration说明、图解IN Inlet 进口in Inch 英寸incl Including包括Ind Indicate 指示Ins Insulation 保温INSP Inspection 检验Instl Installation 安装Int Internal 内部的Int Intermediate 中间的Intmt Intermittent 间歇的、间断的I/O Input/Output 输入 /输出Jt Joint 连接、接头KG Kilogram公斤KW(kw) Kilowatt千瓦LAS Low Alloy Steel 低合金钢lb pound 磅LC Level Control 液位控制器Leng Length 长度LF Female Face 凹面Lg Long 长的LG Level Glass 液位计LH Left Hand 左手Lin Linear 线性的Liq Liquid液体Lj Lap joint搭接LJ Lapped Joint 松套LM Male Face 凸面LMTD Logarithmic Mean Temperature Difference 对数平均温差 LN Liquid Nitrogen 液氮LN Level Normal正常液位Lng Lining衬里Lo Lubrication oil润滑油Lo Low 低LOA Length Over-All 全长总长LOC Location 位置Log Logarithm(to the base 10) 对数（以 10 为底）Long Longitudinal 纵向LP Low Pressure 低压LPG Liquefied Petroleum Gas 液化石油气LT Low Temperature 低温LT Leak Testing 气密试验Ltd Limited有限Ltr Letter 字母、信Lub Lubricate 润滑LW Lap Welding 搭接焊LWN Long Welding Neck 对焊长颈LWS Longitudinal Welded Seam 纵向焊缝 M(m) Meter 米、公尺Mach Machine 机器Maint Maintenance 维修Mat(Mat ’l) Material 材料MAWP Maximum Allowable Working Pressure 最大允许工作压力Max Maximum最大MDMT Min. Design Metallic Temperature 最低设计金属温度Mech Mechanical 机械的Mfd Manufactured 制造的Mfr Manufacturer 制造商MG(mg) Milligram毫克MH Manhole 人孔MI Melt Index熔融指数MIG Metal Inert Gas Arc Welding 熔化极惰性气体保护焊Min Minimum最小MIN(min) Minute分钟MJG Metallic Jacketed Gasket 金属包复垫片Mk Mark标志ml Milliliter毫升mm Millimeter毫米MP Medium Pressure 中压MPC Maximum Permissible Concentration 最大许用浓度MS Medium Pressure Steam 中压蒸汽 MS Medium Steel 中碳钢MSL Mean Sea Level 平均海平面MT Magnetic Particle Examination 磁粉检测Mtd Mounted 安装、装配MTR Material Testing Report 材料试验报告MU Measurement Unit 测量单位MV Mean Value 平均值MW Mineral Wool矿渣棉N North 北NA Not Applicable 不适用的NAT Natural 天然的Natl National 国家的NC America National Coarse Thread 美制粗牙螺纹NDT Nondestructive Testing 无损检验Neg Negative 负NF American National Fine Thread 美国细牙螺纹Nip Nipple 螺纹管接头、短节Nom Nominal 名义Nor Normal 正常NOZ Nozzle 接管NPS American Standard Straight Pipe Thread 美国标准直管螺纹NPSHA Net Positive Suction Head Available 有效汽蚀裕量NPSHR Net Positive Suction Head Required 要求汽蚀裕量NPT American Standard Taper Pipe Thread 美国标准锥管螺纹NT Net Tonnage 净吨数NTP Normal Temperature and Pressure 标准温度和压力NTS Not To Scale 不按比例Num Number 数、编号、号码Obj Object 目标、对象OC Operating Characteristic 操作特性OD Outside Diameter 外径OH Open Hearth 平炉Oper Operating 操作Opp Opposite 对面、相反OR Outside Radius 外半径OR Outside Ring 外环Orien Orientation 方位Ovhd Overhead 高架的、顶部的Oxyg Oxygen 氧 P Page 页P Pressure 压力Par Parallel 平行Para Paragraph节、段PE Polyethylene 聚乙烯PFD Process Flow Diagram 工艺流程图Perform Performance 性能PF Power Factor 功率因素PID Piping & Instruments Diagram 管道和仪表流程图Pl Plate 板Pneum Pneumatic 气、气动PO Purchase Order 订货单Port Portable 便携式、轻便 Posit Positive 正Posit Position 位置ppb Parts per billion 十亿分之几ppm Parts per million 百万分之几Prod Product 产品Proj Project 项目、工程PS Polystyrene 聚苯乙烯psf Pounds per square feet磅/平方英尺 psi Pounds per square inch磅/平方英寸PT Liquid Penetrants Examination 液体渗透检测PTFE Polytetrafluoroethylene 聚四氟乙烯PVA Polyvinyl Acetate 聚醋酸乙烯PVAL Polyvinyl Alcohol聚乙烯醇PVC Polyvinyl Chloride聚氯乙烯PWHT Post Weld Heat Treatment 焊后热处理 QA Quality Assurance 质量保证QC Quality Control 质量控制Qty Quantity 数量Qual Quality 质量R Radius 半径Rad Radial 径向RC Rockwell Hardness 洛氏硬度Recip Reciprocate 往复式Recirc Recirculate 再循环Recom Recommended 建议、推荐Ref Reference 参照、基准Refract Refractory 耐火材料Reg Regulator 调节器Regen Regenerator再生器、再生塔 Reinf Reinforce 加强Rel Relative 相对Rep Report 报告Rep Repeat 重复Reqd Required 要求、需要的REV Revision 修改、版次RF Raise face 突台面RH Relative Humidity 相对湿度RH Right Hand 右手RMS Root Mean Square 均方根 ROT Rotating 旋转rpm revolutions per minute 转/分rps revolutions per second 转/秒RT Radiographic Examination 射线照相检验S South 北SAW Submerged Arc Welding 埋弧焊 Sc Scale 刻度、比例SC Standard Condition 标准状态（温度压力）SCH Schedule 表号、管厚号、进度Sec Second 秒Sec Section 剖面、节、段Seg Segment 节、段 SepSeparator 分离器 SeqSequence次序、顺序 SGSpecific Gravity 比重 SHPShaft Horsepower 轴马力SI Standard International 国际单位制Sig Signal 信号Sld Solid 固体SMAW Shield Metal Arc Welding 手工焊Smls Seamless 无缝的SO Slip on 平焊（法兰）Sol Solution 溶液SP Spare parts备件Sp Special 特殊的、专门的SP Static pressure静压力Spec Specification 说明、规定SpGr Specific Gravity 比重Sq Square 方形、平方SR Stress Relief 消除应力SS Stainless Steel不锈钢 Sta Station 站STD Standard 标准STDWT Standard Weight 标准重量STL Steel 钢STP Standard Temperature and Pressure 标准温度和压力Suc Suction 吸入Suppl Supplement 补充SW Shop Welding 车间焊接SW Spot Weld 点焊SW Socket Welding 承插焊（法兰）SWP Safety Working Pressure安全工作压SYM Symmetry 对称SYS System 系统T Ton 吨TC Tungsten Carbide 碳化钨 Tech Technique 技术TEMA Tubular Exchanger Manufacturers Association 管壳式换热器制造商协会（美国）Temp Temperature 温度Term Terminal 终端、接头Thk Thickness 厚度TIG Tungsten Inert Gas Arc Welding 钨极惰性气体保护焊TL Tangent line 切线Tol Tolerance 公差Tot Total 总Trans Transfer 输送器TW Total Weight 总重TW Tack Welding 定位焊Typ Typical 典型、标准UNC Unified National Coarse Thread 统一标准粗牙螺纹UNF Unified National Fine Thread 统一标准细牙螺纹US Undersize 尺寸过小UT Ultrasonic Examination 超声波探伤UTS Ultimate Tensile Strength 抗拉强度极限Vac Vacuum 真空Vap Vapor 蒸汽Var Variable 变化、变量Vel Velocity 速度Vert Vertical 垂直Vol Volume 体积VT Visual Testing 宏观（目测）检查W Watt 瓦WL Welding Line 焊缝线WL Water Line 水线WPS Welding Procedure Specification 焊接工艺规程WP Working Pressure 工作压力WRC Welding Research Committee 焊接研究委员会（美国）WS Water Supply 供水WT Weight 重量W/V Wind Velocity风速XR X-Ray X 射线Yd Yard 码Yr Year 年external/outide diameter 外径grease 油污。
常用服装英语缩写
常用服装英语缩写A & E=American & Efird, Inc. 美国线业公司A/H，A.H.=armhole 袖窿，[粤]夹圈a/c，acc.=account 帐单，账目a/w.，aw=actual weight 实际重量ABS=area bounded staple fabric 面粘非织造布add.=address 地址ADL=acceptable defect level 允许疵点标准agt.=agent 代理商，代理人amt.=amount 总计，合计，总额AOP=all over printing 全身印花approx.=approximately 约计AQL=acceptable quality level 质量接受标准ar.=around 大约art.=article [欧洲]款式asap.=as soon as possible 尽快ATTN.=attention 注意，收件人aud.=audit 稽核av.=average 平均awb. no.=air way bill no. 运单号B.=back 后B.L.=back length 后长B.N.P.=back neck point 后颈点BNT=back neck tape 后领滚B.P.=bust point 胸高点，乳峰点B.T.=bust top 乳围B.W.=back width 后背宽b/l=bill of lading 提单，提货单bk.=black 黑色BMS.=body measurement system 人体尺寸测量系统BMT.=basic motion time 基本动作时间BNL.=back neckline 后领口BNP，BNPT.=back neck point 后颈点BOC.=band of china 中国银行BOM=bill of material 物料表BP=backpack 背包BRT=barrier removal team 障碍排除小组BSP.=back shoulder point 后肩颈点BTM.=bottom 下摆BTN.=button 钮扣bx.=boxes 箱，盒c.&d. =collected and delivered 货款两清C.A.D.=cash against documents 凭单据付款C.B.，C/B=centre back 后中C.F.，C/F =centre front 前中C.F.，C&F=coat and freight 离岸加运费价格CFT=cross onfunction team 跨功能小组C.P.L.=collar point length 领尖长C.V.C.=chief onvalue of cotton 以棉为主的混纺物c/d.=certificate of delivered 交货证明书C/O，C.O.=country of origin 原产国，产地证c/o label，coo. label=country of origin label 产地唛CAD=computer aided design 电脑辅助设计CAE=computer aided engineering 电脑辅助工程CAL=computer aided layout 电脑辅助排料CAM=computer aided manufacture 电脑辅助制造CAP=computer aided pattern 电脑辅助画样ca.=circa 大约cat.=catalogue （产品）目录cbd.=cash before delivery 付款交货CBL.=center back line 后中线CBM=cubic meter 立方米CBN-W=center back neck point to waist 后颈点至腰CECF=chine export commodities fair 中国出口商品交易会（广交会）cell.=cellular phone 手机cert.=certificate 证书，执照CFS.=container freight station 走拼箱CI=corporate identify 企业标识CIF=cost，insurance & freight 到岸价CNY=Chinese new year 春节（中国新年），China Yuan 人民币col.，clr.=color 颜色CMPT.=cut，make，pack，trim 裁剪+车缝+包装+辅料CMT.=cut，make，trimmings 来料加工（裁剪+车缝+辅料）cord.=corduroy 灯芯绒CS=commercial standards 商业标准C/No.，CTN. No.=carton no. 箱号CY.=container yard 走整柜d. & k.=damaged & kept 染厂对疵布的认赔d.=denier 旦DC=distribution center 配送中心d/y=delivery 出货，交付dbl.=double 双dbl. ndl.=double needles 双针dept.=department 部门dk.=dark 深色DL=Decorative label 主唛doz.=dozen 打DS=Detail Sketch 细节图DTM=dye to match 配色dtmsa.=dye to match surrounding area 配所在部位颜色e.g.=[拉丁]exampli gratia，for example 例如e.p.=elbow point 肘点emb.=embroidery 绣花，[粤]车花eq.=excluding quota 不包括配额eta.=estimated to arrival，estimated time of arrival 预计到达时间etc.=[拉丁]et cetera等等etd.=estimated to departure 预计开船时间etd.=estimated time of delivery 预计出货时间exp.=export 出口ext.=extension number分机号F.=front 前F.L.=front length 前长F.N.P.=front neck point 前颈点F.O.A.=feed off arm 埋夹FAB.=fabric 布料faq.=fair average quality 中等品fb.=freight bill 装货清单FCL.=full container load 走整柜FFM=fully fashion markfluo.=fluorescence 荧光FNP.=front neck point 前颈点FOB.=free on board 离岸价FYR.=for your reference 供参考FQC.=field quality control 现场质量控制FTY.=factory 工厂fyi. =for your informationG.W.=gross weight 毛重 天一服装论坛GBP=great britain pound 英镑GL.=grain line 丝缕，[粤]布纹GOH.=garment on hanger 走挂装H.=hip 坐围H&L=hook & loop 尼龙搭扣h/s=（洗水）手擦H/L=hand loom 手织样HPS=high point of shoulder 高肩点HSP=high shoulder point 高肩点HTM=how to measure 量度方法imag. line=imaginary line 参考线in.=inch 英寸iq.=including quota 包括配额irre. L/C=irrevocable L/C 不可撤销信用证 一路好景jkt.=jacket 夹克K.=knit 针织L.=large 大号L.=left 左L.=length 长度L=ligne 莱尼，号。
物流方面的英语专业术语
物流方面的英语专业术语、组织名称中英对照第一节基本概念术语1 article 物品2 logistics 物流3 logistics activity 物流活动4 logistics operation 物流作业5 logistics modulus 物流模数6 logistics technology 物流技术7 logistics cost 物流成本8 logistics management 物流管理9 logistics center 物流中心10 logistics network 物流网络11 logistics information 物流信息12 logistics enterprise 物流企业13 logistics documents 物流单证14 logistics alliance 物流联盟15 supply logistics 供应物流16 production logistics 生产物流17 distribution logistics 销售物流18 returned logistics 回收物流19 waste material logistics 废弃物物流20 environmental logistics 绿色物流21 internal logistics 企业物流22 external logistics 社会物流23 military logistics 军事物流24 international logistics 国际物流25 Third Part Logistics (TPL）第三方物流26 customized logistics 定制物流27 virtual logistics 虚拟物流28 value—added logistics service 增值物流服务29 supply chain 供应链30 bar code 条码31 Electronic Data Interchange (EDI) 电子数据交换32 tangible loss 有形损耗33 intangible loss 无形损耗二、物流作业术语34 transportation 运输35 combined transport 联合运输36 throuth transport 直达运输37 transfer transport 中转运输38 drop and pull transport 甩挂运输39 containerized transport 集装运输40 container transport 集装箱运输41 door—to—door 门到门42 door to cy 门到场43 door to cfs 门到站44 Full Container Load (FCL）整箱货45 Less—than Container Load （LCL）拼箱货46 storing 储存47 storage 保管48 article reserves 物品储存49 inventory 库存50 cycle stock 经常库存51 safety stock 安全库存52 inventory cycle time 库存周期53 lead time 前置期(或提前期) 54 order cycle time 订货处理周期55 goods stack 货垛56 stacking 堆码57 handling carrying 搬运58 loading and unloading 装卸59 unit loading and unloading 单元装卸60 package/packaging 包装61 sales package 销售包装62 packing of nominated brand 定牌包装63 neutral packing 中立包装64 transport package 运输包装65 palletizing 托盘包装66 containerization 集装化67 in bulk 散装化68 cross docking 直接换装69 distribution 配送70 joint distribution 共同配送71 distribution center 配送中心72 sorting 分拣73 order picking 拣选74 goods collection 集货75 assembly 组配76 distribution processing 流通加工77 cold chain 冷链78 inspection 检验第三节物流技术装配及设施术语79 warehouse 仓库80 storehouse 库房81 automatic warehouse 自动化仓库82 stereoscopic warehouse 立体仓库83 virtual warehouse 虚拟仓库84 boned warehouse 保税仓库85 export supervised warehouse 出口监管仓库86 cargo under custom’s supervision 海关监管货物87 chill space 冷藏区88 freeze space 冷冻区89 humidity controlled space 控湿储存区90 temperature controlled space 温度可控区91 receiving space 收货区92 shipping space 发货区93 goods shed 料棚94 goods yard 货场95 goods shelf 货架96 pallet 托盘97 fork lift truck 叉车98 converyor 输送机99 Automatic Guided Vehicle （AGV) 自动导引机100 box car 箱式车101 container 集装箱102 Twenty-feet Equivalent Unit （TEU) 换算箱103 speciffic cargo container 特种货物集装箱104 full container ship 全集装箱船105 railway container yard 铁路集装箱场106 inland container depot 公路集装箱中转站107 container terminal 集装箱码头108 international through railway transport 国际铁路联运109 international multimodal transport 国际多式联运110 land bridge transport 大陆桥运输111 liner transport 班轮运输112 shipping by chartering 租船运输113 shipping agency 船务代理114 international freight forwarding agent 国际货运代理115 tally 理货116 international transportation cargo insurance 国际货物运输保险117 customs declaration 报关118 customs broker 报关行119 commodity inspection 进出口商品检验第四节物流管理术语120 logistics strategy 物流战略121 logistics strategy management 物流战略管理122 warehouse management 仓库管理123 warehouse layout 仓库布局124 inventory control 库存控制125 Economic Order Quantity (EOQ）经济订货批量126 Fixed Quantity System （FQS) 定量订货方式127 Fixed Interval System （FIS）定期订货方式128 ABC classification ABC分类管理129 Electronic Order System （EOS) 电子订货系统130 Just-in—time （JIT) 准时制131 just-in—time logistics 准时制物流132 zero—inventory logistics 零库存技术133 logistics cost control 物流成本管理134 Material Requirements Planning (MRP）物料需要计划135 Manufacturing Resource Planning (MRP Ⅱ）制造资源计划136 Distribution Requirements Planning (DRP) 配送需要计划137 Distribution Resource Planning (DRPⅡ）配送资源计划138 Logistics Resource Planning （LRP) 物流资源计划139 Enterprise Resource Planning (ERP）企业资源计划140 Supply Chain Management (SCM）供应链管理141 Quick Response （QR) 快速反应142 Efficient Customer Response (ECR) 有效客户反应143 Continuous Replenishment Program (CRP）连续库存补充计划144 Computer Assisted Ordering （CAO) 计算机辅助订货系统145 Vendor Managed Inventory (VMI）供应商管理库存146 outsourcing 业务外包第五节其他常见术语147 accounting cost 会计成本148 accuracy audit 正确性审计149 Activity Based Classification ABC分类法150 actual weight 实际重量151 added value 附加价值152 after-sales service 售后服务153 aggregate shipments 合并出货154 air pollution 空气污染155 air freight 空运货件156 Application Service Provider （ASP) 应用供应商157 arbitrage 套利158 asset recovery 资源回收159 Automated Storage and Retrieval System (ASRS）自动仓储系统160 Automated Vehicle Identification (AVI）自动车辆识别161 automated warehouse 自动仓库162 Automated Vehicle Location (AVL) 自动车辆位置163 available vehicle capacity 车辆承载能力164 average clear stacking height 平均净堆叠高度165 back haul 回程166 backwardation 现货溢价167 bar code label 条形码标签168 bar code scanner 条形码扫描机169 base stock 基本存货170 batch numbers 批号171 bay 区域172 bear 卖空者173 bear market 熊市174 belt conveyor 皮带式输送带175 bi—directional read 双向读取176 Bill of Lading (B/L) 托运单177 Bill of Materials (BOM) 物料用量清单178 broken carton 已拆箱179 broker 经纪人180 bulk carrier 散装运送业181 bulk container 散装集装箱182 bull 卖空者183 bull market 牛市184 Business Process Reengineering (BPR) 业务流程重组185 cancellation charge 取消订单费用186 cargo 货物187 cargo booking 预约托运188 cargo inspection 检查货物189 cash discount 现金折扣190 centralized dispatching 集中式派车191 centralized procurement 集中采购192 channel of distribution 分销渠道193 check in 进货清点194 Chief Logistics Officer (CLO）物流主管195 claim 索赔196 closed distribution system 封闭式配送系统197 consumer physical distribution 消费者物流198 container terminal 集装箱码头199 cooperative buying 联合采购200 cost control 成本控制201 crane 起重机202 cubed out 装载率203 customer service 客户服务204 Customer Relationship Management （CRM) 客户关系管理205 data warehousing 数据仓库206 deadhead 空回头车207 declining conveyor 倾斜式输送机208 de—consolidation center 分货中心209 delivery costs 配送成本210 delivery cycle 配送周期211 delivery error 误送212 delivery note 出货清单213 delivery terminal 配送站214 demand forecasting 需求预测215 depalletizer 卸托盘机216 design for logistics 为物流而设计217 direct distribution 直接配送218 direct store delivery 直接配送到商店219 dispatct area 出货区220 Distributed Resource Planning (DRP) 分销资源计划221 Decision Support System (DSS）决策支持系统222 domestic intercity trucking 国内长途货运223 domestic logistics 国内物流224 double floor stacking 双层堆积225 double pallets handling 双托盘处理226 double — pallet jack 双托盘设备227 duty 关税228 economic stock 经济存货229 electronic clearance 电子通关230 export 出口231 exclusive distribution 独家分销232 Executive Support System （ESS）高层主管支持系统233 fact tag 产品说明标签234 factory price 出厂价235 firewall 防火墙236 fixed rack 固定式货架237 flatbed trailer 平台拖车238 fleet 车(船)队239 furniture removal carriers 搬家公司240 gateway 转运站241 Geographic Information System (GIS) 地理信息系统242 Global Positioning System （GPS）全球定位系统243 global logistics 全球物流244 hand truck 手推车245 handheld scanner 手提式扫描仪246 heat insulating material 隔热材料247 hot tag 紧急标签248 Industrial Engineering (IE）工业工程249 integrated logistics 集成物流250 Integrated Services Digital Network （ISDN) 综合业务数据网251 interchange terminal 联运站252 inventory control 库存控制253 joint distribution 共同配送254 kanban system 看板系统255 knowledge management 知识管理256 label making machine 标签机257 laser scanner 激光扫描仪258 logistician 物流师259 logisticis engineering 物流工程260 logistics management 物流管理261 loose packages 散装262 make to order 定单生产263 market orientation 市场导向264 marking machine 打标机265 market share 市场份额266 materials handing equipment 物料搬运设备267 middleware 中间件268 multi - story warehouse 多层仓库269 net weight 净重270 noise pollution 噪音污染271 number plate 牌照272 on season 旺季273 Open DataBase Connectivity （ODBC) 开放数据库互联274 optical scanners 光学扫描仪275 order processing 定单处理276 Order Point System (OPS）定货点法277 overload 超载278 package 包裹279 process center 处理中心280 procurement 采购281 quality control 质量控制282 quarantine 检疫283 quotas 配额284 rack 货架285 regional distribution center 区域物流中心286 retail selling 零售287 safety stock 安全库存288 sealing machine 封装机289 supply chain 供应链290 Supply Chain Management (SCM) 供应链管理291 tank container 罐装集装箱292 temporary labor 临时工293 Theory of Constraint （TOC) 约束理论294 vacuum packaging 真空包装295 vehicle 车辆296 voice recognition 语音识别297 warehousing 仓储298 waste 废弃物299 wholesalers 批发商300 zero stock 零库存。
物流方面的英语专业术语
物流方面的英语专业术语、组织名称中英对照第一节基本概念术语1 article 物品2 logistics 物流3 logistics activity 物流活动4 logistics operation 物流作业5 logistics modulus 物流模数6 logistics technology 物流技术7 logistics cost 物流成本8 logistics management 物流管理9 logistics center 物流中心10 logistics network 物流网络11 logistics information 物流信息12 logistics enterprise 物流企业13 logistics documents 物流单证14 logistics alliance 物流联盟15 supply logistics 供应物流16 production logistics 生产物流17 distribution logistics 销售物流18 returned logistics 回收物流19 waste material logistics 废弃物物流20 environmental logistics 绿色物流21 internal logistics 企业物流22 external logistics 社会物流23 military logistics 军事物流24 international logistics 国际物流25 Third Part Logistics (TPL）第三方物流26 customized logistics 定制物流27 virtual logistics 虚拟物流28 value-added logistics service 增值物流服务29 supply chain 供应链30 bar code 条码31 Electronic Data Interchange （EDI) 电子数据交换32 tangible loss 有形损耗33 intangible loss 无形损耗二、物流作业术语34 transportation 运输35 combined transport 联合运输36 throuth transport 直达运输37 transfer transport 中转运输38 drop and pull transport 甩挂运输39 containerized transport 集装运输40 container transport 集装箱运输41 door-to—door 门到门42 door to cy 门到场43 door to cfs 门到站44 Full Container Load (FCL）整箱货45 Less—than Container Load (LCL) 拼箱货46 storing 储存47 storage 保管48 article reserves 物品储存49 inventory 库存50 cycle stock 经常库存51 safety stock 安全库存52 inventory cycle time 库存周期53 lead time 前置期（或提前期) 54 order cycle time 订货处理周期55 goods stack 货垛56 stacking 堆码57 handling carrying 搬运58 loading and unloading 装卸59 unit loading and unloading 单元装卸60 package/packaging 包装61 sales package 销售包装62 packing of nominated brand 定牌包装63 neutral packing 中立包装64 transport package 运输包装65 palletizing 托盘包装66 containerization 集装化67 in bulk 散装化68 cross docking 直接换装69 distribution 配送70 joint distribution 共同配送71 distribution center 配送中心72 sorting 分拣73 order picking 拣选74 goods collection 集货75 assembly 组配76 distribution processing 流通加工77 cold chain 冷链78 inspection 检验第三节物流技术装配及设施术语79 warehouse 仓库80 storehouse 库房81 automatic warehouse 自动化仓库82 stereoscopic warehouse 立体仓库83 virtual warehouse 虚拟仓库84 boned warehouse 保税仓库85 export supervised warehouse 出口监管仓库86 cargo under custom’s supervision 海关监管货物87 chill space 冷藏区88 freeze space 冷冻区89 humidity controlled space 控湿储存区90 temperature controlled space 温度可控区91 receiving space 收货区92 shipping space 发货区93 goods shed 料棚94 goods yard 货场95 goods shelf 货架96 pallet 托盘97 fork lift truck 叉车98 converyor 输送机99 Automatic Guided Vehicle (AGV) 自动导引机100 box car 箱式车101 container 集装箱102 Twenty—feet Equivalent Unit （TEU) 换算箱103 speciffic cargo container 特种货物集装箱104 full container ship 全集装箱船105 railway container yard 铁路集装箱场106 inland container depot 公路集装箱中转站107 container terminal 集装箱码头108 international through railway transport 国际铁路联运109 international multimodal transport 国际多式联运110 land bridge transport 大陆桥运输111 liner transport 班轮运输112 shipping by chartering 租船运输113 shipping agency 船务代理114 international freight forwarding agent 国际货运代理115 tally 理货116 international transportation cargo insurance 国际货物运输保险117 customs declaration 报关118 customs broker 报关行119 commodity inspection 进出口商品检验第四节物流管理术语120 logistics strategy 物流战略121 logistics strategy management 物流战略管理122 warehouse management 仓库管理123 warehouse layout 仓库布局124 inventory control 库存控制125 Economic Order Quantity (EOQ）经济订货批量126 Fixed Quantity System （FQS) 定量订货方式127 Fixed Interval System (FIS）定期订货方式128 ABC classification ABC分类管理129 Electronic Order System (EOS）电子订货系统130 Just-in-time （JIT) 准时制131 just—in-time logistics 准时制物流132 zero—inventory logistics 零库存技术133 logistics cost control 物流成本管理134 Material Requirements Planning （MRP）物料需要计划135 Manufacturing Resource Planning (MRP Ⅱ) 制造资源计划136 Distribution Requirements Planning （DRP) 配送需要计划137 Distribution Resource Planning （DRPⅡ）配送资源计划138 Logistics Resource Planning （LRP) 物流资源计划139 Enterprise Resource Planning （ERP）企业资源计划140 Supply Chain Management （SCM) 供应链管理141 Quick Response （QR) 快速反应142 Efficient Customer Response （ECR) 有效客户反应143 Continuous Replenishment Program （CRP）连续库存补充计划144 Computer Assisted Ordering (CAO）计算机辅助订货系统145 Vendor Managed Inventory (VMI）供应商管理库存146 outsourcing 业务外包第五节其他常见术语147 accounting cost 会计成本148 accuracy audit 正确性审计149 Activity Based Classification ABC分类法150 actual weight 实际重量151 added value 附加价值152 after—sales service 售后服务153 aggregate shipments 合并出货154 air pollution 空气污染155 air freight 空运货件156 Application Service Provider (ASP）应用供应商157 arbitrage 套利158 asset recovery 资源回收159 Automated Storage and Retrieval System (ASRS) 自动仓储系统160 Automated Vehicle Identification (AVI）自动车辆识别161 automated warehouse 自动仓库162 Automated Vehicle Location (AVL）自动车辆位置163 available vehicle capacity 车辆承载能力164 average clear stacking height 平均净堆叠高度165 back haul 回程166 backwardation 现货溢价167 bar code label 条形码标签168 bar code scanner 条形码扫描机169 base stock 基本存货170 batch numbers 批号171 bay 区域172 bear 卖空者173 bear market 熊市174 belt conveyor 皮带式输送带175 bi-directional read 双向读取176 Bill of Lading （B/L）托运单177 Bill of Materials （BOM) 物料用量清单178 broken carton 已拆箱179 broker 经纪人180 bulk carrier 散装运送业181 bulk container 散装集装箱182 bull 卖空者183 bull market 牛市184 Business Process Reengineering （BPR) 业务流程重组185 cancellation charge 取消订单费用186 cargo 货物187 cargo booking 预约托运188 cargo inspection 检查货物189 cash discount 现金折扣190 centralized dispatching 集中式派车191 centralized procurement 集中采购192 channel of distribution 分销渠道193 check in 进货清点194 Chief Logistics Officer （CLO) 物流主管195 claim 索赔196 closed distribution system 封闭式配送系统197 consumer physical distribution 消费者物流198 container terminal 集装箱码头199 cooperative buying 联合采购200 cost control 成本控制201 crane 起重机202 cubed out 装载率203 customer service 客户服务204 Customer Relationship Management （CRM) 客户关系管理205 data warehousing 数据仓库206 deadhead 空回头车207 declining conveyor 倾斜式输送机208 de—consolidation center 分货中心209 delivery costs 配送成本210 delivery cycle 配送周期211 delivery error 误送212 delivery note 出货清单213 delivery terminal 配送站214 demand forecasting 需求预测215 depalletizer 卸托盘机216 design for logistics 为物流而设计217 direct distribution 直接配送218 direct store delivery 直接配送到商店219 dispatct area 出货区220 Distributed Resource Planning (DRP) 分销资源计划221 Decision Support System （DSS) 决策支持系统222 domestic intercity trucking 国内长途货运223 domestic logistics 国内物流224 double floor stacking 双层堆积225 double pallets handling 双托盘处理226 double - pallet jack 双托盘设备227 duty 关税228 economic stock 经济存货229 electronic clearance 电子通关230 export 出口231 exclusive distribution 独家分销232 Executive Support System （ESS）高层主管支持系统233 fact tag 产品说明标签234 factory price 出厂价235 firewall 防火墙236 fixed rack 固定式货架237 flatbed trailer 平台拖车238 fleet 车（船）队239 furniture removal carriers 搬家公司240 gateway 转运站241 Geographic Information System （GIS）地理信息系统242 Global Positioning System （GPS）全球定位系统243 global logistics 全球物流244 hand truck 手推车245 handheld scanner 手提式扫描仪246 heat insulating material 隔热材料247 hot tag 紧急标签248 Industrial Engineering (IE）工业工程249 integrated logistics 集成物流250 Integrated Services Digital Network (ISDN）综合业务数据网251 interchange terminal 联运站252 inventory control 库存控制253 joint distribution 共同配送254 kanban system 看板系统255 knowledge management 知识管理256 label making machine 标签机257 laser scanner 激光扫描仪258 logistician 物流师259 logisticis engineering 物流工程260 logistics management 物流管理261 loose packages 散装262 make to order 定单生产263 market orientation 市场导向264 marking machine 打标机265 market share 市场份额266 materials handing equipment 物料搬运设备267 middleware 中间件268 multi - story warehouse 多层仓库269 net weight 净重270 noise pollution 噪音污染271 number plate 牌照272 on season 旺季273 Open DataBase Connectivity （ODBC）开放数据库互联274 optical scanners 光学扫描仪275 order processing 定单处理276 Order Point System （OPS) 定货点法277 overload 超载278 package 包裹279 process center 处理中心280 procurement 采购281 quality control 质量控制282 quarantine 检疫283 quotas 配额284 rack 货架285 regional distribution center 区域物流中心286 retail selling 零售287 safety stock 安全库存288 sealing machine 封装机289 supply chain 供应链290 Supply Chain Management (SCM) 供应链管理291 tank container 罐装集装箱292 temporary labor 临时工293 Theory of Constraint （TOC）约束理论294 vacuum packaging 真空包装295 vehicle 车辆296 voice recognition 语音识别297 warehousing 仓储298 waste 废弃物299 wholesalers 批发商300 zero stock 零库存。
物流英语词汇
物流英语词汇1、freight rates 运费率2、freight absorption [əbˈsɔ:pʃən, -ˈzɔ:p-运费免收3、volume of freight 货运量4、dead freight 空舱费5、freight agent 运输行6、freight car [美](一节)货车7、freight engine 货运机车8、freight house 货栈, 堆栈9、freight ton [tonnage] 容积吨(数)10、freight-in n. (=freight inward, transportation-in)进货运费11、freight-out n. (=freight outward, transportation-out)销货运费12、freight forward 运费由提货人支付13、freight paid 运费付讫14、freight prepaid (=advanced freight) 运费先付15、freightless adj.16、by freight [美]用普通铁路货车运送17、dead freight 空舱费; 空舱；不易腐坏的大件货物18、drag one’s freight [美俚]离开, 出发19、pull one’s freight [美俚]离开, 出发20、additional freight 增列运费, 附加运费21、ad valorem freight 从价运费22、advanced freight 预付运费23、air freight 航空运费24、astray freight[əstreɪ]票货分离(但有到达站和货主标计)的货物25、back freight 退货运费, 额外运费, 空车回送方向货物26、back goods freight 退货费用27、bulk freight 散装货物28、charterer’s freight [ˈtʃɑ:tərə]租船人的运费29、clausum freight 不动产占有侵犯30、collect freight 待收运费, 收取运费31、cost and freight 离岸加运费价格32、cost, assurance and freight 到岸价格33、cost insurance freight 到岸价格34、direct freight 直航运费35、distance freight 增加距离运费36、distress freight[dis tre s填载运费37、excess freight[ekses超(过路程单填明数)量货物38、export freight & insurance a/c 出口保险费运费科目(帐户)39、fast freight 快运货物40、general freight 普通货物41、groupage freight 化零为整的货物42、home freight 返回运费, 回程运费43、inbound freight 到达货物1. 回内地的;归本国的2. 到达的；入境的44、inflammablefreight 易燃货物45、interline freight 铁路联运货物46、less-than-carload freight (LCL freight) 零担货物47、lump sum freight 按整船计算的运费.包干运费48、manifest freight 快运货物49、measurement freight 按体积计算的运费50、multiple freight 复式运费51、net freight 运费纯收入, 运费实收金, 运费净数52、nonrevenue freight [ˈnɔnˈrevinju:]无收入货物53、open freight 自由运费, 未定运费54、outbound freight 运出货物55、outward freight 销出运费56、overland freight 陆运货运57、package freight 包裹货运, 零担货物58、phantom freight 在售价上加计的假设运费59、pro rata freight 比例运费60、quick dispatch freight 快运货物61、refused freight 收货人拒收的货物62、restricted freight 限制条件下运输的货物(如易燃品, 易爆品等)63、return cargo freight 回运货物运费64、river freight 内河水脚, 内河运费65、shipping freight 运费66、shortfall freight 亏舱运费67、tapering freight 远距离递减的运费68、through freight 直达运费, 联运货物69、freight on board 离岸价格70、freight on inter-branch transfers 分店间送货运费71、freight to be collected 运到收费, 运费待收72、freight to be deducted [di dʌkt（扣除）应扣代付运费第一节基本概念术语1 article 物品2 logistics 物流3 logistics activity 物流活动4 logistics operation 物流作业5 logistics modulus 物流模数6 logistics technology 物流技术7 logistics cost 物流成本8 logistics management 物流管理9 logistics center 物流中心10 logistics network 物流网络11 logistics information 物流信息12 logistics enterprise 物流企业13 logistics documents 物流单证14 logistics alliance 物流联盟15 supply logistics 供应物流16 production logistics 生产物流17 distribution logistics 销售物流18 returned logistics 回收物流19 waste material logistics 废弃物物流20 environmental logistics 绿色物流21 internal logistics 企业物流22 external logistics 社会物流23 military logistics 军事物流24 international logistics 国际物流25 Third Part Logistics (TPL) 第三方物流26 customized logistics 定制物流27 virtual logistics 虚拟物流28 value-added logistics service 增值物流服务29 supply chain 供应链30 bar code 条码31 Electronic Data Interchange (EDI) 电子数据交换32 tangible loss 有形损耗33 intangible loss 无形损耗二、物流作业术语34 transportation 运输35 combined transport 联合运输36 throuth transport 直达运输37 transfer transport 中转运输38 drop and pull transport 甩挂运输39 containerized transport 集装运输40 container transport 集装箱运输41 door-to-door 门到门42 door to cy 门到场43 door to cfs 门到站44 Full Container Load (FCL) 整箱货45 Less-than Container Load (LCL) 拼箱货46 storing 储存47 storage 保管48 article reserves 物品储存49 inventory 库存50 cycle stock 经常库存51 safety stock 安全库存52 inventory cycle time 库存周期53 lead time 前置期(或提前期)54 order cycle time 订货处理周期55 goods stack 货垛56 stacking 堆码57 handling carrying 搬运58 loading and unloading 装卸59 unit loading and unloading 单元装卸60 package/packaging 包装61 sales package 销售包装62 packing of nominated brand 定牌包装63 neutral packing 中立包装64 transport package 运输包装65 palletizing 托盘包装66 containerization 集装化67 in bulk 散装化68 cross docking 直接换装69 distribution 配送70 joint distribution 共同配送71 distribution center 配送中心72 sorting 分拣73 order picking 拣选74 goods collection 集货75 assembly 组配76 distribution processing 流通加工77 cold chain 冷链78 inspection 检验第三节物流技术装配及设施术语79 warehouse 仓库80 storehouse 库房81 automatic warehouse 自动化仓库82 stereoscopic warehouse 立体仓库83 virtual warehouse 虚拟仓库84 boned warehouse 保税仓库85 export supervised warehouse 出口监管仓库86 cargo under custom's supervision 海关监管货物87 chill space 冷藏区88 freeze space 冷冻区89 humidity controlled space 控湿储存区90 temperature controlled space 温度可控区91 receiving space 收货区92 shipping space 发货区93 goods shed 料棚94 goods yard 货场95 goods shelf 货架96 pallet 托盘97 fork lift truck 叉车98 converyor 输送机99 Automatic Guided Vehicle (AGV) 自动导引机100 box car 箱式车101 container 集装箱102 Twenty-feet Equivalent Unit (TEU) 换算箱103 speciffic cargo container 特种货物集装箱104 full container ship 全集装箱船105 railway container yard 铁路集装箱场106 inland container depot 公路集装箱中转站107 container terminal 集装箱码头108 international through railway transport 国际铁路联运109 international multimodal transport 国际多式联运110 land bridge transport 大陆桥运输111 liner transport 班轮运输112 shipping by chartering 租船运输113 shipping agency 船务代理114 international freight forwarding agent 国际货运代理115 tally 理货116 international transportation cargo insurance 国际货物运输保险117 customs declaration 报关118 customs broker 报关行119 commodity inspection 进出口商品检验第四节物流管理术语120 logistics strategy 物流战略121 logistics strategy management 物流战略管理122 warehouse management 仓库管理123 warehouse layout 仓库布局124 inventory control 库存控制125 Economic Order Quantity (EOQ) 经济订货批量126 Fixed Quantity System (FQS) 定量订货方式127 Fixed Interval System (FIS) 定期订货方式128 ABC classification ABC分类管理129 Electronic Order System (EOS) 电子订货系统130 Just-in-time (JIT) 准时制131 just-in-time logistics 准时制物流132 zero-inventory logistics 零库存技术133 logistics cost control 物流成本管理134 Material Requirements Planning (MRP) 物料需要计划135 Manufacturing Resource Planning (MRP Ⅱ) 制造资源计划136 Distribution Requirements Planning (DRP) 配送需要计划137 Distribution Resource Planning (DRPⅡ) 配送资源计划138 Logistics Resource Planning (LRP) 物流资源计划139 Enterprise Resource Planning (ERP) 企业资源计划140 Supply Chain Management (SCM) 供应链管理141 Quick Response (QR) 快速反应142 Efficient Customer Response (ECR) 有效客户反应143 Continuous Replenishment Program (CRP) 连续库存补充计划144 Computer Assisted Ordering (CAO) 计算机辅助订货系统145 Vendor Managed Inventory (VMI) 供应商管理库存146 outsourcing 业务外包第五节其他常见术语147 accounting cost 会计成本148 accuracy audit 正确性审计149 Activity Based Classification ABC分类法150 actual weight 实际重量151 added value 附加价值152 after-sales service 售后服务153 aggregate shipments 合并出货154 air pollution 空气污染155 air freight 空运货件156 Application Service Provider (ASP) 应用供应商157 arbitrage 套利158 asset recovery 资源回收159 Automated Storage and Retrieval System (ASRS) 自动仓储系统160 Automated Vehicle Identification (AVI) 自动车辆识别161 automated warehouse 自动仓库162 Automated Vehicle Location (AVL) 自动车辆位置163 available vehicle capacity 车辆承载能力164 average clear stacking height 平均净堆叠高度165 back haul 回程166 backwardation 现货溢价167 bar code label 条形码标签168 bar code scanner 条形码扫描机169 base stock 基本存货170 batch numbers 批号171 bay 区域172 bear 卖空者173 bear market 熊市174 belt conveyor 皮带式输送带175 bi-directional read 双向读取176 Bill of Lading (B/L) 托运单177 Bill of Materials (BOM) 物料用量清单178 broken carton 已拆箱179 broker 经纪人180 bulk carrier 散装运送业181 bulk container 散装集装箱182 bull 卖空者183 bull market 牛市184 Business Process Reengineering (BPR) 业务流程重组185 cancellation charge 取消订单费用186 cargo 货物187 cargo booking 预约托运188 cargo inspection 检查货物189 cash discount 现金折扣190 centralized dispatching 集中式派车191 centralized procurement 集中采购192 channel of distribution 分销渠道193 check in 进货清点194 Chief Logistics Officer (CLO) 物流主管195 claim 索赔196 closed distribution system 封闭式配送系统197 consumer physical distribution 消费者物流198 container terminal 集装箱码头199 cooperative buying 联合采购200 cost control 成本控制201 crane 起重机202 cubed out 装载率203 customer service 客户服务204 Customer Relationship Management (CRM) 客户关系管理205 data warehousing 数据仓库206 deadhead 空回头车207 declining conveyor 倾斜式输送机208 de-consolidation center 分货中心209 delivery costs 配送成本210 delivery cycle 配送周期211 delivery error 误送212 delivery note 出货清单213 delivery terminal 配送站214 demand forecasting 需求预测215 depalletizer 卸托盘机216 design for logistics 为物流而设计217 direct distribution 直接配送218 direct store delivery 直接配送到商店219 dispatct area 出货区220 Distributed Resource Planning (DRP) 分销资源计划221 Decision Support System (DSS) 决策支持系统222 domestic intercity trucking 国内长途货运223 domestic logistics 国内物流224 double floor stacking 双层堆积225 double pallets handling 双托盘处理226 double - pallet jack 双托盘设备227 duty 关税228 economic stock 经济存货229 electronic clearance 电子通关230 export 出口231 exclusive distribution 独家分销232 Executive Support System (ESS) 高层主管支持系统233 fact tag 产品说明标签234 factory price 出厂价235 firewall 防火墙236 fixed rack 固定式货架237 flatbed trailer 平台拖车238 fleet 车(船)队239 furniture removal carriers 搬家公司240 gateway 转运站241 Geographic Information System (GIS) 地理信息系统242 Global Positioning System (GPS) 全球定位系统243 global logistics 全球物流244 hand truck 手推车245 handheld scanner 手提式扫描仪246 heat insulating material 隔热材料247 hot tag 紧急标签248 Industrial Engineering (IE) 工业工程249 integrated logistics 集成物流250 Integrated Services Digital Network (ISDN) 综合业务数据网251 interchange terminal 联运站252 inventory control 库存控制253 joint distribution 共同配送254 kanban system 看板系统255 knowledge management 知识管理256 label making machine 标签机257 laser scanner 激光扫描仪258 logistician 物流师259 logisticis engineering 物流工程260 logistics management 物流管理261 loose packages 散装262 make to order 定单生产263 market orientation 市场导向264 marking machine 打标机265 market share 市场份额266 materials handing equipment 物料搬运设备267 middleware 中间件268 multi - story warehouse 多层仓库269 net weight 净重270 noise pollution 噪音污染271 number plate 牌照272 on season 旺季273 Open DataBase Connectivity (ODBC) 开放数据库互联274 optical scanners 光学扫描仪275 order processing 定单处理276 Order Point System (OPS) 定货点法277 overload 超载278 package 包裹279 process center 处理中心280 procurement 采购281 quality control 质量控制282 quarantine 检疫283 quotas 配额284 rack 货架285 regional distribution center 区域物流中心286 retail selling 零售287 safety stock 安全库存288 sealing machine 封装机289 supply chain 供应链290 Supply Chain Management (SCM) 供应链管理291 tank container 罐装集装箱292 temporary labor 临时工293 Theory of Constraint (TOC) 约束理论294 vacuum packaging 真空包装295 vehicle 车辆296 voice recognition 语音识别297 warehousing 仓储298 waste 废弃物299 wholesalers 批发商300 zero stock 零库存。
服装关键部位英文缩写
服装关键部位英文缩写【篇一：服装关键部位英文缩写】a e=american efird, inc.美国线业公司a/h，a.h.=armhole 袖窿，[粤]夹圈a/c，acc.=account 帐单，账目a/w.，aw=actual weight 实际重量abs=area bounded staple fabric 面粘非织造布add.=address 地址adl=acceptable defect level 允许疵点标准agt.=agent 代理商，代理人amt.=amount 总计，合计，总额aop=all over printing 全身印花approx.=approximately 约计aql=acceptable quality level 质量接受标准ar.=around 大约art.=article [欧洲]款式asap.=as soon as possible 尽快attn.=attention 注意，收件人aud.=audit 稽核av.=average 平均awb. no.=air way bill no. 运单号b.=back 后b.=bust (女)胸围b.l.=back length 后长b.n.p.=back neck point 后颈点bnt=back neck tape 后领滚b.p.=bust point 胸高点，乳峰点b.t.=bust top 乳围b.w.=back width 后背宽b/l=bill of lading 提单，提货单bk.=black 黑色bms.=body measurement system 人体尺寸测量系统bmt.=basic motion time 基本动作时间bnl.=back neckline 后领口bnp，bnpt.=back neck point 后颈点boc=bank of china 中国银行bom=bill of material 物料表bp=backpack 背包brt=barrier removal team 障碍排除小组bsp.=back shoulder point 后肩颈点btm.=bottom 下摆btn.=button 钮扣bx.=boxes 箱，盒c. d. =collected and delivered 货款两清c.=chest (男)胸围c.a.d.=cash against documents 凭单据付款c.b.，c/b=centre back 后中c.f.，c/f =centre front 前中c.f.，c f=coat and freight离岸加运费价格cft=cross function team 跨功能小组c.p.l.=collar point length 领尖长c.v.c.=chief value of cotton 以棉为主的混纺物c/d.=certificate of delivered 交货证明书c/o，c.o.=country of origin 原产国，产地证c/o label，coo. label=country of origin label 产地唛cad=computer aided design 电脑辅助设计cae=computer aided engineering 电脑辅助工程cal=computer aided layout 电脑辅助排料cam=computer aided manufacture 电脑辅助制造cap=computer aided pattern 电脑辅助画样ca.=circa 大约cat.=catalogue (产品)目录cbd.=cash before delivery 付款交货cbl.=center back line 后中线cbm=cubic meter 立方米cbn-w=center back neck point to waist 后颈点至腰cecf=chine export commodities fair中国出口商品交易会(广交会) cell.=cellular phone 手机cert.=certificate 证书，执照cfs.=container freight station 走拼箱ci=corporate identify 企业标识cif =cost，insurance freight 到岸价cny=chinese new year春节(中国新年)，china yuan 人民币col.，clr.=color 颜色cmpt.=cut，make，pack，trim 裁剪+车缝+包装+辅料cmt.=cut，make，trimmings 来料加工(裁剪+车缝+辅料)cord.=corduroy 灯芯绒cs=commercial standards 商业标准c/no.，ctn. no.=carton no. 箱号cy.=container yard 走整柜d. k.=damaged kept 染厂对疵布的认赔d.=denier 旦dc=distribution center 配送中心d/y=delivery 出货，交付dbl.=double 双dbl. ndl.=double needles双针dept.=department 部门dk.=dark 深色dl=decorative label 主唛doz.=dozen 打ds=detail sketch 细节图dtm=dye to match 配色dtmsa.=dye to match surrounding area 配所在部位颜色e.g.=[拉丁]exampli gratia，for example 例如e.p.=elbow point 肘点emb.=embroidery 绣花，[粤]车花eq.=excluding quota 不包括配额eta.=estimated to arrival，estimated time of arrival 预计到达时间etc.=[拉丁]et cetera等等etd.=estimated to departure 预计开船时间etd.=estimated time of delivery 预计出货时间exp.=export 出口ext.=extension number分机号f.=front 前f.l.=front length 前长f.n.p.=front neck point 前颈点f.o.a.=feed off arm 埋夹fab.=fabric 布料faq.=fair average quality 中等品fb.=freight bill 装货清单fcl.=full container load 走整柜ffm=fully fashion markfluo.=fluorescence 荧光fnp.=front neck point 前颈点fob .=free on board 离岸价fyr.=for your reference 供参考fqc.=field quality control 现场质量控制fty.=factory 工厂fyi. =for your informationg.w.=gross weight 毛重gbp=great britain pound 英镑gl.=grain line 丝缕，[粤]布纹goh.=garment on hanger 走挂装h.=hip 坐围h l=hook loop 尼龙搭扣h/s=(洗水)手擦h/l=hand loom 手织样hps=high point of shoulder 高肩点hsp=high shoulder point 高肩点htm=how to measure 量度方法imag. line=imaginary line 参考线in.=inch 英寸iq.=including quota 包括配额irre. l/c=irrevocable l/c 不可撤销信用证jkt.=jacket 夹克k.=knit 针织l.=large 大号l.=left 左l.=length 长度l=ligne 莱尼，号。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Update date:20131115
Project Name
Assembly
Picture
Item
Webber Part
Name
Cobinet
Part Name
Part Picture P/N Materil Usage Desc Weight Property CHN .NAME Remark 1Cover
ASA RAL7035
(light gray)
1XH上盖2Splice Tray
ASA RAL7035
(light gray)
1XH摇板3Reserve noses
ASA RAL7035
(light gray)
6XH卡块4Housing
ASA RAL7035
(light gray)
1XH底座5Sepatator PMMA1XH透明板
6
Flange Plate (For
SC)
Al1XH法兰板1 7
Flange Plate (For
E2000)
Al1XH法兰板2 8
Flange Plate (For
SC-DX)
Al1XH法兰板3 9Foam Out-let1XH出线口泡棉
采购，如公司有
尺寸相近的，可
考虑使用
10Small cable tie Nylon5100*2.6Purchased Part小扎带
采购，如公司有
尺寸相近的，可
考虑使用
11Small cable tie Nylon2200*4.8Purchased Part大扎带
魔术贴，采购12small velcro2200*7Purchased Part魔术贴
不干胶，外发打
印
13
sticker cable
assign
1Purchased Part理线标贴
打印，考虑外发
用铜版纸打印
14
sticker cap
unlocking
1Purchased Part拆装标贴
由采购负责15
sticker laser
warning
1Purchased Part小心激光标贴
防水接头M20,16
cable connection
M20
Nylon1Purchased Part防水接头
暂无详细信息17
mounting
instruction
1Purchased Part安装说明
三号桥采购18screw 3x8
Stainless
steel
6Purchased Part
M3*8不锈钢自攻螺
丝，平头平尾十字
槽
For Clip
三号桥采购19screw 4x8
Stainless
steel
3Purchased Part
M4*8不锈钢自攻螺
丝，圆头平尾十字
槽
cable anchorage
and
splicecassette
塞头 M20 十字
槽
20
lock screw for
cable connection
M20
Nylon1Purchased Part防水堵头M20
三号桥采购21
screw 5x40 DIN
7996
Stainless
steel
4Purchased Part
DIN 7996 M5*40不
锈钢木工圆头十字
槽自攻螺丝
Wall Mount 三号桥采购22anchor bolt 6x35Nylon4Purchased Part M5塑料膨胀管
XH23Foam Foam1Purchased Part防水圈Water Proof 三号桥采购24
Washers 5.3x10x1
DIN 125
Stainless
steel
4Purchased Part
DIN125 不锈钢垫
圈5.3*10*1
Wall Mount
51
ODB
Item 1,2,3,4,5,9,18,23 should be assembly by Webber .
All the parts should be prepared by Webber.
Distribution Box Bom。