品质人员名称类英语词汇
工厂常用英语
制造业常用英语词汇总经理办公室General manager’s office模具部Tooling department项目部Project department品质部Quality department计划部 Plan department制造部Manufacture departmentKeypad产品部Keypad departmentIMD 产品部 IMD department五金部 Metal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section 计划科 Plan section仓务科 Warehouse section商务科 Business section品质规划科 quality plan sectionIQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中心 measurement center项目规划科 Project plan section项目XX科 Project section XX试模科 Mold test section成本科 Cost section设备科 Facility section采购科 Purchase section综合办 General affairs office编程科 Programming section模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中心 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop装配车间Assembly workshop总经理General manager (GM)经理managerXX部门经理Manager of XX department原料库 Raw material warehouse半成品库 Semi-finished product warehouse 成品库 Finished product warehouse科长 section chief主任 chief部门主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant职员staff二、产品超声波焊接ultrasonic welding塑胶件 Plastic parts塑材 Raw parts喷涂件 Painted parts装配件 Assembly parts零件 Component原料 Raw material油漆 Paint稀释剂 Thinner油墨 Ink物料编号part number三、模具注塑模具injection mold冲压模具Stamping tool模架mold base定模座板Fixed clamp plate A板A plateB板B plate支承板 support plate方铁 spacer plate回位销 Return pin导柱 Guide pin动模座板Moving clamp plate 顶针ejector pin单腔模具single cavity mold 多腔模具multi-cavity mold 浇口gate合模力clamping force锁模力locking force开裂crack循环时间cycle time老化aging螺杆screw镶件 Insert主流道 sprue分流道runner浇口gate直浇口 direct gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate浇口套sprue bush流道板runner plate排气槽vent分型线（面）parting line定模Fixed mold动模movable mold型腔cavity凹模cavity plate，凸模core plate斜销angle pin滑块slide拉料杆sprue puller定位环locating ring脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mold 熔合纹weld line三板式模具three plate mold 脱模ejection脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure保压时间holding time闭模时间closing time电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine平面磨床Surface grinding machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller倒角chamfer键Key键槽keyway间距pitch快速成型模Rapid prototype tool （RPT）四、品管SPC statistic process control品质保证Quality Assurance(QA)品质控制Quality control(QC)来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration环境试验Environmental test光泽gloss拉伸强度tensile strength盐雾实验salt spray test翘曲warp比重specific gravity疲劳fatigue撕裂强度tear strength缩痕sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计划sampling plan抗张强度 Tensile Strength抗折强度 Flexural Strength硬度 Rigidity色差 Color Difference涂镀层厚度 Coating Thickness导电性能 Electric Conductivity粘度 viscosity附着力 adhesion耐磨 Abrasion resistance尺寸 Dimension(喷涂)外观问题 Cosmetic issue不合格品 Non-conforming product限度样板 Limit sample五、生产注塑机injection machine冲床Punch machine嵌件注塑 Insert molding双色注塑 Double injection molding薄壁注塑 Thin wall molding膜内注塑 IMD molding ( In-mold decoration）移印 Tampo printing丝印 Silk screen printing热熔 Heat staking超声熔接 Ultrasonic welding (USW）尼龙nylon黄铜 brass青铜 bronze紫(纯)铜 copper料斗hopper麻点pit配料compounding涂层coating飞边flash缺料 Short mold烧焦 Burn mark缩水 Sink mark气泡 Bubbles破裂 Crack熔合线 Welding line流痕 Flow mark银条 Silver streak黑条 Black streak表面光泽不良 Lusterless表面剥离 Pelling翘曲变形 Deformation脏圬 Stain mark油污 Oil mark蓝黑点 Blue-black mark顶白 Pin mark拉伤 Scratch限度样品 Limit sample最佳样品 Golden sample预热preheating再生料recycle material机械手 Robot机器人 Servo robot试生产 Trial run; Pilot run (PR)量产 mass production切料头 Degate产能 Capacity能力 Capability参数 Parameter二次加工 Secondary process六．物控保质期shelf lifeABC分类法ABC Classification装配Assembly平均库存Average Inventory批号Batch Number批量生产Mass Production提货单Bill of Lading物料清单Bill of Material采购员Buyer检查点Check Point有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust 作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required需求管理Demand Management需求Demand工程变更生效日期Engineering Change Effect Date呆滞材料分析Excess Material Analysis完全跟踪Full Pegging在制品库存In Process Inventory投入/产出控制Input/ Output Control检验标识Inspection ID库存周转率Inventory Carry Rate准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time负荷Loading仓位代码Location Code仓位状况Location Status批量标识Lot ID批量编号Lot Number批量Lot Size机器能力Machine Capacity机器加载Machine Loading制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning现有库存量On-hand Balance订单输入Order Entry零件批次Part Lot零件编号Part Number (P/N)零件Part领料单Picking List领料/提货Picking产品控制Product Control产品线Production Line采购订单跟踪Purchase Order Tracking需求量Quantity Demand毛需求量Quantity Gross安全库存量Safety Stock在制品Work in Process零库存Zero Inventories七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核 Audit能力 Capability能力指数 Capability Indices控制计划 Control Plans纠正措施 Corrective Action文件 Documentation作业指导书 Standard operation procedure (SOP); Work instruction不合格品 Nonconformance不合格 Nonconformity每百万零件不合格数 Defective Parts Per Million, DPPM预防措施 Preventive Action程序Procedures过程流程图 Process Flow Diagram, Process Flow Chart质量手册Quality Manual质量计划 Quality Plan质量策划 Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair返工Rework现场Site分承包方Subcontractors产品product质量quality质量要求quality requirement顾客满意customer satisfaction质量管理体系quality management system质量方针quality policy质量目标quality objective质量管理quality management质量控制quality control质量保证quality assurance组织organization顾客customer供方supplier过程process服务service设计与开发design and development：特性characteristic可追溯性trace ability合格conformity缺陷defect纠正correction让步concession放行release报废scrap规范specification检验inspection试验test验证verification评审review测量measurement普通原因Common Cause均值Mean极差Range稳定性Stability计量型数据Variables Data变差Variation重复性Repeatability再现性Reproducibility稳定性Stability分辨率Resolution过程更改Process change质量功能展开QFD外观项目Appearance Item初始过程能力Preliminary Process Capability 材料清单Bill of Material设计确认Design Validation设计验证Design Verification八．常用缩略词语OEM Original Equipment Manufacturer ANOVA 方差分析法 Analysis of VarianceDFMEA 设计失效模式及后果分析 Design Failure Mode and Effects Analysis DOE 试验设计 Design of ExperimentGR&R 量具的重复性和再现性Gage Repeatability and Reproducibility PFMEA 过程失效模式及后果分析Process Failure Mode and Effect Analysis QSR 质量体系要求Quality System RequirementQFD 质量功能展开 Quality Function DeploymentBOM 物料清单 Bill of MaterialCpk 稳定过程的能力指数 Capability for stable processLCL 下控制限 Lower Control LimitUCL 上控制限 Upper Control LimitLSL 工程规范下限 Lower Specification LimitX(—)--R图均值一极差图 Average-Range Chart防错（POKA-YOKE）Mistake ProofingETA 预计到达 Estimate to be arrivePO 定单 Purchase orderM/C 机器 machineRFQ 报价需求 Request for quotationMFI 熔融流动指数 Melt flow indexFAI 全尺寸检测报告 First article inspectionCOC 材质证明 Certificate of complianceALT 加速老化试验 Accelerated life testCRR 承认书 Component review reportOT 加班 Over timeCAP 矫正计划 Corrective action planR&D 研发 Research and DevelopmentASAP 尽快 As soon as possibleECN工程更改通知Engineering change noticeDCN 设计更改通知 Design change noticeOTD 准时交货 On time delivery九．通用词语确保 ensure构想 construct会签 con-sign功能 Function机构 organization外观 appearance适用 apply to作业流程 Operation flow附件 attachment商务人员 business personnel汇总 summarize指定相关人员 designated personnel新产品开发说明会 new product development explanation meeting拟定 Prepare委托 entrust认证 qualify电子档 Soft copy3D文件 3D database移转 Transfer执行 ConductXXX申请单 XXX Application form客户要求 Customer requirement启动 Kick off评估 Evaluation作业员 Operator批准, 承认 Approval合同评审 Contract review可靠性 Reliability相关的 Relevant程序 Procedure制程 Process流程图 Flow chart产品 Product生产 Production资材 Logistics责任 Responsibility跟进 Follow-up交付 Delivery汇总 Summarize外协加工 subcontract指定相关人员 designated personnel编号 number附件 attachment产品名称 Description周期循环时间 Cycle time模具号 Mold No,数量 quantity ( Qt’y )备注 remarkSAP号 SAP No.客户 Customer表单 Form初步的 Preliminary版本 Version根本原因 Root cause（喷漆）夹具 Fixture（设备）小夹具 Jig设备 Equipment设施 Facility送，提交（样品）Submit责任部门,责任人 Responsible by（大的）目标 Objective(小的，具体的)目标 Target格式 Format上岗证 Qualification card需求 Requirement现场 On site查检表 Checklist试产 pilot增值税 VAT---value-added tax品质专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条码System：系统System Barcode：系统条码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Riser card：转接卡Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control 生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证 SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力)PMP:制程管理计划（生产管制计划）MPI:制程分析DAS efects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List)QCD: Quality cost delivery（品质，交期，成本）MPM:Manufacturing project management制造专案管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造 (Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理 (Just In Time)QCC ：品管圈 (Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子资料交换 (Electronic Data Interchange)EIS ：主管决策系统 (Excutive Information System)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System)MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning)MRPⅡ：制造资源计划 (Manufacturing Resource Planning)OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture) OLAP：线上分析处理 (On-Line Analytical Processing)OLTP：线上交易处理 (On-Line Transaction Processing)OPT ：最佳生产技术 (Optimized Production Technology) PDCA：PDCA管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management))RCCP：粗略产能规划 (Rough Cut Capacity Planning)SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面品质管制 (Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据 Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceablity 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: Voice of Customer 客户需求136 VOE: Voice of Engineer 工程需求137 Inventory stock report:庫存清单报告138 Sales order report:出货报告质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令。
品质术语(英语)
Military-Standard
ห้องสมุดไป่ตู้军用
S I-S IV Special I-Special IV 抽样水准等级
特殊
P/N Part Number 料号
L/N Lot Number 特采 AOD Accept On Deviation 特采 UAI Use As It 首件检查报告
FPIR First Piece Inspection Report 百万分之一
checked by 初审 approved by 核准 department 部门
part number/ P/N 料号
item/group/class 类别
quality 品质 prepared by 制表 notes 说明 finished product 成品 semi-finished product 半成品 packing materials 包材 good product/accepted goods/ accepted parts/good parts 良品 defective product/non-good parts 不良 品 disposed goods 处理品
N Number 样品数
其它品质术语类
QCC Quality Control Circle 品质 圈
QIT Quality Improvement Team 品 质改善小组
PPM Percent Per Million 批号 制程统计品管专类
SPC Statistical Process Control 统 计制程管制
SQC Statistical Quality Control 统 计品质管制
R Range 全距 AR Averary Range 全距平均值
英语个人品质词汇
个人品质词汇able有才干的，能干的active主动的，活跃的adaptable适应性强的adroit灵巧的，机敏的aggressive有进取心的alert机灵的ambitious有雄心壮志的amiable和蔼可亲的amicable友好的analytical善于分析的apprehensive有理解力的aspiring有志气的，有抱负的audacious大胆的，有冒险精神的capable有能力的，有才能的careful办事仔细的candid正直的charitable宽厚的competent能胜任的confident有信心的conscientious认真的，自觉的considerate体贴的constructive建设性的contemplative好沉思的cooperative有合作精神的creative富创造力的dashing有一股子冲劲的，有拼搏精神的dedicated有奉献精神的devoted有献身精神的dependable可靠的diplomatic老练的，有策略的disciplined守纪律的discreet(在行动，说话等方面)谨慎的dutiful尽职的dynamic精悍的earnest认真的well-educated受过良好的efficient有效率的energetic精力充沛的enthusiastic充满热情的expressive善于表达faithful守信的，忠诚的forceful(性格)坚强的frank直率的，真诚的friendly友好的frugal俭朴的generous宽宏大量的genteel有教养的gentle有礼貌的hard-working勤劳的hearty精神饱满的honest诚实的hospitable殷勤的humble恭顺的humorous幽默的impartial公正的independent有主见的industrious勤奋的ingenious有独创性的initiative首创精神have an inquiring mind爱动脑筋intellective有智力的intelligent理解力强的inventive有发明才能的，有创造力的just正直的kind-hearted好心的knowledgeable有见识的learned精通某门学问的liberal心胸宽大的logical条理分明的loyal忠心耿耿的methodical有方法的modest谦虚的motivated目的明确的objective客观的open-minded虚心的orderly守纪律的original有独创性的painstaking辛勤的，苦干的，刻苦的practical实际的precise一丝不苟的persevering不屈不挠的punctual严守时刻的purposeful意志坚强的qualified合格的rational有理性的realistic实事求是的reasonable讲道理的reliable可信赖的responsible负责的self-conscious自觉的selfless无私的sensible明白事理的sincere真诚的smart精明的spirited生气勃勃的sporting光明正大的steady塌实的straightforward老实的strict严格的systematic有系统的strong-willed意志坚强的sweet-tempered性情温和的temperate稳健的tireless孜孜不倦的。
工厂相关英语
部分工厂常用英文,供大家参考部分工厂常用英文,供大家参考.Education and Training教育训练proposal improvement/creative suggestion提案改善BS Brain Storming 脑力激荡QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结DCC delivery control center 交货管制中心3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品7SClassification整理(sorting, organization)-seiriRegulation整顿(arrangement, tidiness)-seiton Cleanliness清扫(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教养(discipline)-shitsukeSave 节约Safety安全质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门QC Section品管课administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板flat cable 排线resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈packaging tool打包机packaging打包品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理工厂常用缩略语５Ｓ：５Ｓ管理ＡＢＣ：作业制成本制度(Activity-Based Costing)ＡＢＢ：实施作业制预算制度(Activity-Based Budgeting)ＡＢＭ：作业制成本管理(Activity-Base Management)ＡＰＳ：先进规画与排程系统(Advanced Planning and Scheduling) ＡＳＰ：应用程序服务供货商（Application Service Provider）ＡＴＰ：可承诺量(Available To Promise)ＢＯＭ：物料清单(Bill Of Material)ＢＰＲ：企业流程再造(Business Process Reengineering)ＢＳＣ：平衡记分卡(Balanced ScoreCard)ＢＴＦ：计划生产(Build To Forecast)ＢＴＯ：订单生产(Build To Order)ＣＰＭ：要径法(Critical Path Method)ＣＲＭ：客户关系管理(Customer Relationship Management)ＣＲＰ：产能需求规划(Capacity Requirements Planning)ＣＴＯ：客制化生产(Configuration To Order)ＤＢＲ：限制驱导式排程法(Drum-Buffer-Rope)ＤＲＰ：运销资源计划(Distribution Resource Planning)ＤＳＳ：决策支持系统(Decision Support System)ＥＣ：设计变更／工程变更(Engineer Change)ＥＣ：电子商务(Electronic Commerce)ＥＤＩ：电子资料交换(Electronic Data Interchange)ＥＩＳ：主管决策系统(Excutive Information System)ＥＯＱ：基本经济订购量(Economic Order Quantity)ＥＲＰ：企业资源规划(Enterprise Resource Planning)ＦＭＳ：弹性制造系统(Flexible Manufacture System)ＦＱＣ：成品品质管制(Finish or Final Quality Control)ＩＰＱＣ：制程品质管制(In-Process Quality Control)ＩＱＣ：进料品质管制(Incoming Quality Control)ＪＩＴ：实时管理(Just In Time)ＫＭ：知识管理(Knowledge Management)Ｌ４Ｌ：逐批订购法(Lot-for-Lot)ＬＴＣ：最小总成本法(Least Total Cost)ＬＵＣ：最小单位成本(Least Unit Cost)ＭＥＳ：制造执行系统(Manufacturing Execution System)ＭＰＳ：主生产排程(Master Production Schedule)ＭＲＰ：物料需求规划(Material Requirement Planning)ＭＲＰⅡ：制造资源计划(Manufacturing Resource Planning)ＯＥＭ：委托代工(Original Equipment Manufacture)ＯＤＭ：委托设计与制造(Original Design & Manufacture)ＯＬＡＰ：线上分析处理(On-Line Analytical Processing)ＯＬＴＰ：线上交易处理(On-Line Transaction Processing)ＯＰＴ：最佳生产技术(Optimized Production Technology)ＯＱＣ：出货品质管制(Out-going Quality Control)ＰＤＣＡ：PDCA管理循环(Plan-Do-Check-Action)ＰＤＭ：产品数据管理系统(Product Data Management)ＰＥＲＴ：计画评核术(Program Evaluation and Review Technique)ＰＯＨ：预估在手量(Project on Hand)ＱＣＣ：品管圈(Quality Control Circle)ＲＣＣＰ：粗略产能规划(Rough Cut Capacity Planning)ＲＯＰ：再订购点(Re-Order Point)ＳＣＭ：供应链管理(Supply Chain Management)ＳＦＣ：现场控制(Shop Floor Control)ＳＩＳ：策略信息系统(Strategic Information System)ＳＰＣ：统计制程管制(Statistic Process Control)ＴＯＣ：限制理论(Theory of Constraints)ＴＱＣ：全面品质管制(Total Quality Control)ＴＱＭ：全面品质管理(Total Quality Management)ＷＩＰ：在制品(Work In Process)>>> ５Ｓ：５Ｓ管理5S是由JP企业研究出来的一种环境塑造方案，其目的在藉由整理(SEIRI)、整顿(SEITON)、清扫(SEISO)、清洁(SEIKETSU)及身美(SHITSUKE)五种行为来创造清洁、明朗、活泼化之环境，以提高效率、品质及顾客满意度。
生产品质工程用到的IE专业英语对照词汇
BS Brain Storming 脑力激荡Facilities Design and Planning设施规划与设计Material Flow System Analysis物流系统分析Production Planning and Control生产计划与控制Human Engineering人机工程(工效学)Cost Control成本控制Value Engineering价值工程Work Assessment工作评价与考核Engineering Economics Analysis工程经济分析Machine Interference机器干扰Single Minute Exchange of Dies (SMED) 六十秒即时换模Fool-Proof 防止错误法(防错法)Man 人Machine 机Material 料Method 法Environment 环境Temperature(temp)温度Humidity湿度leaning curve学习曲线Time measurement 时间测量Methods of time measurement原则时间测量(MTM)Shop floor observation 现场观测Line Balancing 线平衡Value有价值NO VALUE 无价值Incidental work(necessary)必要Waste挥霍Takt Time生产节拍Transport Empty 伸手Grasp 握取Move 移物Disassemble 折卸Use 应用Assemble 装配Release Load 放手Inspect 检查Search 寻找Select 选择Play 计划Pre-Position预定位Position 定位Hold 持住Rest 休息Unavoidable Delay 迟延Avoidable Delay 故延E: Elimination剔除C :Combination合并R: Re-arrangement重排S :Simplification简化PRA-Probabilistic Risk风险率评估Risk Priority Number (RPN) 风险关键指数What 完毕了什么where 何处做When 何时做who 由谁做Why 为何这样做how 何时做delay等待operation操作inspection检查transportation搬运storage储存Color management 颜色管理Quality Control Circle 品管圈(QCC)Activity-Base Management作业制成本管理(ABM)In-Process Quality Control制程质量管理(IPQC)Incoming Quality Control进料质量管理(IQC)International Organization for Standardization国际原则组织(ISO) Predetermined Motion Time Standard 简称PTS 预定动作时间原则法Methods-time-measurement 措施时间衡量Work factor system 工作原因法(WF)Modolar arrangement of pre-determind time standard MOD法Leveling 平准化= westing 西屋法objective rating 客观评比synthetic leveling 合成评比Work Sampling 工作抽样Motion time analysis 动作时间分析Business Process Reengineering (BPR)企业流程再造Enterprise Resource Planning ERP企业资源规划Economic Order Quantity (EOQ)基本经济订购量Flexible Manufacture System 弹性制造系统(FMS)Finish or Final Quality Control成品质量管理(FQC)In-Process Quality Control制程质量管理(IPQC)Incoming Quality Control进料质量管理(IQC)Just In Time实时管理(JIT)Manufacturing Execution System制造执行系统(MES) Master Production Scheduling主生产排程(MPS) Master Production Planning主生产计划Material Requirement Planning物料需求规划(MRP) Manufacturing Resource Planning制造资源计划(MRPII) Operation Scheduling作业计划Flow shop流水车间Optimized Production Technology最佳生产技术Supply Chain Management供应链管理(SCM)Statistic Process Control记录制程管制(SPC)Total Production Management全面生产管理(TPM) Total Quality Management全面质量管理(TQM)Zero Defect Quality Control零缺陷质量管理:PDCA Cycle PDCA循环:continue Improvement持续改善:Project项目Project Manager项目经理Project Management项目管理Project Plan项目计划Process Improvement现场改善WORK IN PROCESS 半成品Visual management 目视管理bottleneck 瓶颈Layout 布置图quality engineering 质量工程人员(QE)first article inspection 新品首件检查(FAI)first article assurance首件确认(FAA)capability index能力指数(CP)Quality Improvement Team 质量改善小组(QIT)Classification整顿(sorting, organization)-seiriRegulation整顿(arrangement, tidiness)-seitonCleanliness打扫(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教养(discipline)-shitsukeSave 节省Safety安全Make-to-stock备货型生产(MTS)Make-to-order订货型生产(MTO)Assemble-to-order按订单装配(ATO)Flexible manufacturing system柔性制造系统Group technology成组技术(GT)Concurrent engineering并行工程(CE)Time compression technology时间压缩技术(TCT)Business process reengineering业务过程重组(BPR)Agile manufacturing敏捷制造(AM)Leap production精细生产(LP)Intelligent manufacturing 智能制造(IM)Computer-aided-manufacturing计算机辅助制造(CAM) Computer-aided-design计算机辅助设计(CAD)Computer-aided-engineering计算机辅助工程(CAE)Computer-aided-process planning计算机辅助工艺编制( CAPP) overall cost leadership成本优先differentiation独具一格Market focus集中一点cost efficiency成本效率quality质量Dependability可靠性Flexibility柔性product date management产品数据管理(PDM)Facility location设施选址Fixed position layout固定式布置process layout工艺过程布置layout based on group technology成组制造单元布置Job design工作设计work measurement工作测量Time study时间研究Basic motion study基本动作世界研究法(BMS)Modolar arrangement of predetermind time standard模特法Human factor engineering人因工程business plan经营计划Fixed capacity固定能力Adjustable capacity可?#123;整能力production rate生产率Inventory库存Job-shop production单间小批生产Bill of materials (BOM)物料清单文献Lead time提前期modular bill of materials模块物料清单Maximum part-period gain最大周期收益(MPG) distribution requirements planning分派需求计划scheduling编制作业计划sequencing排序Dispatching派工controlling控制expediting赶工supply chain供应链Purchasing Management采购管理Quick Response迅速顾客反应JIT Purchasing准时采购physical distribution物流Materials handling物料搬运project项目critical path method关键路线法optimistic time最乐观时间Most likely time最也许时间pessimistic time最消极时间Mean time between failure平均故障期(MTBF) Mean time to repair平均维修期(MTTR)plan 计划do 执行check 检查action 处理level production生产平准化optimized production technology最优生产技术(OPT) Overall Equipment Effectiveness整体设备效能Operation Research运筹学Service Sector服务业Operation Management运作管理Operation System运作系统World Class Manufacturing世界级制造Time-based Competition基于时间旳竞争Operation Flexibility运作战略Product Development产品开发Dependent Demand独立需求Economic Order Lot 经济订货批量:Safety Stock安全库存Shortage Costs缺货成本ABC Classing Method A BC分类法Reorder Point订货点Holding Costs存储成本Productivity Improvement Team生产力提高小组(PIT) Productivity Improvement Center生产力提高中心(PIC) Break PAD 折PADBreak PIN 折脚Paste Base 沾BASEapproved by: 核准Apr.(April) 四月assembly(ass’y)组合Aug.(August) 八月Base 底座bifilar 双线并绕Bobbin（BBN）绕线管bottom 底部Brush Epoxy On Core 铁芯刷胶Brush Epoxy On Loop 线圈刷胶checked by: 审核Choke电感clip耳夹close winding密绕component 组件condition条件condition条件copper铜箔立式core铁芯Curing烘烤current 电流CUT WIRE 裁线Dec.(December) 十二月defective product box不良品箱deficient manufacturing procedure制程不良description: 阐明Design Failure Mode and Effect Analysis DFMEA设计Desk Topdip 浸入Direction 方向ECN Engineering Change Notice工程变更告知Electronic Magnetic In EMI 抗电磁干扰Enameled copper wire 漆包线Engineering Change Request 工程变更规定epoxy胶equipment/instrument设备Failure Mode and Effect Analysis FMEA失效模式与效应分析Feb.(February) 二月fixture治具flow chart 流程窗体flux助焊剂FN: Factory Notice 工厂告知FN: Immediated change 立即变更Function test 测试gap 间隙,缝隙HI-POT安规测试IE﹕Industrial Engineering 工业工程impregnation浸泡inductance 电感ink油墨inspection(INSP)检查Insulating Tape绝缘胶布issued date: 发行日期item发料Jan.(January) 一月Joint Quality Engineering (JQE)Jul.(July) 七月Jun.(June) 六月Kapton Tape高温胶布layer 层line线Magnetic Components 磁性组件magnetic 磁性旳Mar.(March) 三月Margin Tape安胶marking印章materials物料May五月ME: Mechanical Engineering 机械工程measurement测试mechanical dimension 外观尺寸MFG: manufacturing制造Mini-TowerModel: 机种Not Deviate Measure 量平整度Nov.(November) 十一月O/I Operation Instruction 作业指导书Oct.(October) 十月OEM:委托代工(Original Equipment Manufacture)oven 烤箱P/n: part number 品名P/R Pilot-Run试作验证pad 垫片PE Production／Process Engineering 制造工程/制程工程pin adjustment对脚PIN BENDING& WIRE TRIMMING 折弯钢片pin 脚plastic 塑料,塑料poor processing 制程不良Pre-soldering 预焊primary(pri)初级process 流程production capacity生产力卧式production control (PC)生管purchasing采购QCC:品管圈(Quality Control Circle)QE:质量工程(Quality Engineering)remark: 备注Reported by: 草拟Revision（REV﹒）: 版本sample样品schematic 构造图second(sec)次级Sept.(September) 九月solder bar锡棒solder iron 烙铁solder wire锡丝soldering焊锡solvent 稀释剂space winding疏绕Specification （Spec）生产规格stand-off 凸点station 站别step步序straighten 弄直,使变直tape 胶带TE: Test Engineering 测试工程terminal 脚,端子Time (时间)timer定期器top顶部,上层transformer 变压器trifler三线并绕tube 套管turn ratio圈数比turn圈数twist绞线vacuum抽真空varnish dipping泡凡立水varnish凡立水warehouse仓库winding direction 绕线方向winding绕线wire trimming理线。
冲压模具专业英语
冲压模具专业术语英汉对照目录一，模具厂常用之标准零配件二，模具钢材三，组装、冲压、喷漆等专业词汇四，模具工程常用词汇五，模具零件类六，品质人员名称类七，系统文件类八，模具技术用语九，各式模具分类用语十，模具常用之工作机械设备十一,表面处理关连用语十二，成形不良用语十三，各种冲模加工关连用语十四,模具常用刀具与工作法用语十五，冲压机械及周边关连用语十六,线切割放电加工关连用语十七，模具加工方法十八，机械设计及周边其他用语一,模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴（模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧？goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶？冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶？lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导？pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re—entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide（slide core）滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料? spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板二，模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel ?钢vinyl tapped steel sheet 塑胶覆面钢板三，组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs。
富士康工厂内部常用英语-值得看看
公司英语-----教育训练部一:常用术语Hon Hai 鸿海CMM Component module move 机动组件整合CEM Contract Manufaction service 合约委托代工IBSC Internet Business Solution Center 国际互联网应用中心PCEG Personal Computer Enclosure group 个人计算机外设事业群（FOXTEQ）CCBG Connector&cable business groupCPBG Competition business groupESBG Enterprise system business group 鸿富锦事业群SABG system assembly business group 系统组装事业群NWE Net Work EnclosureNSE Network system enclosureNSG Network system groupNFE Network flexible enclosureFoxcavity = HZ = Hong Zhun 鸿准Stamping tool shop I 冲模一厂Stamping tool shop II 冲模二厂Prototype workshop 样品中心Steel factory 裁剪厂PCE molding tooling workshop PCE塑模厂Hua Nan test and measurement center 华南检测中心MPE mobile phone enclosure MPEMBE mobile phone and notebook enclosure 明塑厂MGE Alloy magnesium alloy enclosure 镁合金Engineer standard 工标Document center (database center)数据中心Design Center 设计中心Painting 烤漆(厂) Assembly组装(厂) Stamping 冲压(厂) Education and Training教育训练proposal improvement/creative suggestion提案改善Technological exchange and study 技术交流研习会Technology and Development Committee 技术发展委员会BS Brain Storming 脑力激荡QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结DCC delivery control center 交货管制中心3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品Core value（核心价值）Love 爱心Confidence 信心Decision 决心Corporate culture(公司文化)Integration 融合Responsibility 责任Progress 进步3T STRATEGYTime to market 及时切入生产Time to volume 及时大量生产Time to money 及时大量交货FOUR CONTROL SYSTEM 四大管制系统Engineering control system 工程管制系统Quality control system质量管理系统Manufacturing control system生产管制系统Management control system经营管制系统7SClassification整理(sorting, organization)-seiriRegulation整顿(arrangement, tidiness)-seitonCleanliness清扫(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教养(discipline)-shitsukeSave 节约Safety安全二:英文缩写质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理PQC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 品质方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 数据中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)标识符SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessA VL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类president董事长operator作业员position职务general manager总经理deputy manager |'depjuti| =vice manager副理group leader组长line leader线长supervisor 课长Human Resources Department人力资源部Head count 人头数planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录subject主题conclusion结论decision items决议事项Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工单revision版次remark备注registration登记registration card登记卡to control管制applicationformforpurchaseconsume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 扁平电缆TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to,switching over切换enineringbottleneck,projctdifficulty工glove(s)手套glove(s)withexposedfingersBand-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉伸work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子guide plate定位板sliding block滑块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cuttingdie,blankingdiedie block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱dowel pin固定销coil spring弹簧lifter pin顶料销pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, locationblock定位块reset复位to file burr 锉毛刺embedded lump |in'bed| |l mp|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys 花键 quenching 淬火 tempering 回火 annealing 退火 carbonization 碳化 alloy 合金forming 成型(抽凸,冲凸) draw hole 抽孔 bending 折弯 emboss 凸点 dome 凸圆semi-shearing 半剪 stamp mark 冲记号 deburr or coin 压毛边 punch riveting 冲压铆合 side stretch 侧冲压平reel stretch 卷圆压平 groove 压线stamp letter 冲字(料号)tick-mark nearside 正面压印 tick-mark farside 反面压印 extension DWG 展开图 procedure DWG 工程图die structure DWG 模具结构图冲压类punch, press 冲punching machine 冲床 hydraulic machine 油压机 jack 升降机 decoiler 整平机manufacture management 制造管理 stamping, press 冲压 feeder 送料机rack, shelf, stack 料架 taker 取料机to reverse material 翻料 to load material 上料 to unload material 卸料to return material/stock to 退料scraped |'skr æpid|报废 scrape ..v.刮;削 robot 机械手production line 流水线 packaging tool 打包机 packaging 打包成型类well type 蓄料井insulated runner 绝缘浇道方式 hot runner 热浇道 runner plat 浇道模块 valve gate 阀门浇口band heater 环带状的电热器 spindle 阀针spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 air vent 排气道 welding line 熔合痕 eject pin 顶出针 knock pin 顶出销return pin 回位销反顶针 sleeve 套筒stripper plate 脱料板 insert core 放置入子 guide pin 导销subzero 深冷处理three plate 三极式模具 runner system 浇道系统 stress crack 应力电裂 orientation 定向sprue gate 射料浇口，直浇口 nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井 side gate 侧浇口 edge gate 侧缘浇口 tab gate 搭接浇口 film gate 薄膜浇口 flash gate 闸门浇口 slit gate 缝隙浇口 fan gate 扇形浇口 dish gate 因盘形浇口 diaphragm gate 隔膜浇口 ring gate 环形浇口submarine gate 潜入式浇口 tunnel gate 隧道式浇口pin gate 针点浇口 runner less 无浇道sprue less 无射料管方式 long nozzle 延长喷嘴方式 spur 浇口;溶 waste 废料 board 广告牌sliding rack 滑料架 to impose lines 压线to compress, compressing 压缩 character die 字模 to feed, feeding 送料material change, stock change 材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution 转速 abnormal handling 异常处理组装类Assembly line 组装线 Layout 布置图Conveyer 流水线运输带 Rivet machine 拉钉机 Rivet gun 拉钉枪 Screw driver 起子Electric screw driver 电动起子 Hydraulic machine 液压机 P n e u m automation 自动化 to stake, staking, riveting 铆合 add lubricant oil 加润滑油 argon welding 氩焊 cylinder 油缸 robot 机械手conveying belt 输送带 transmission rack 输送架 to draw holes 抽孔 bolt 螺栓 nut 螺母 screw 螺丝identification tag 标示单 screwdriver plug 起子插座 automatic screwdriver 自动启子be put in storage 入库packing 包装fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet/skid 栈板 barcode 条形码barcode scanner 条形码扫描仪 fuse together 熔合fuse machine/heat stake 热熔机processing, to process 加工 delivery, to deliver 交货 to return delivery to. to send delivery b a c k t oretu r n ofgoo d easily damaged parts 易损件 standard parts 标准件 to lubricate 润滑 spring 弹簧 tox machine 自铆机 烤漆类 phosphate 皮膜化成 viscosity 涂料粘度 alkalidipping 脱脂 main manifold 主集流脉 organic solvent 有机溶剂 demagnetization 去磁;消磁 high-speed transmission 高速传递 heat dissipation 热传 rack 上料 volatile 挥发性 degrease 脱脂 rinse 水洗 alkaline etch 龄咬 desmot 剥黑膜 D.I. rinse 纯水次 Chromate 铬酸处理Anodize 阳性处理 seal 封孔 scraped products 报放品 disposed products 处理品 dismantle the die 折模 auxiliary function 辅助功能 heater band 加热片 thermocouple 热电偶 derusting machine 除锈机 degate 打浇口 dryer 烘干机 induction 感应 induction light 感应光 r e s p ons e =r e a c t i o n =i n t e r ac t i o ram 连杆 edge finder 巡边器 concave 凸 convex 凹 cold slug 冷块 blush 导色 gouge 沟槽;凿槽 satin texture 段面咬花 witness line 证示线 grit 沙砾 granule =pellet =grain 细粒 sand blasting 喷沙 grit maker 抽粒机 cushion 缓冲 fillet 镶;嵌边 roller pin formality 滚针形式 cam driver 铡楔 shank 摸柄 crank shaft 曲柄轴 品质类 qualified products, up-to-grade products 良品 defective products, not up-to-grade products 不良品 defective product box 不良品箱 poor processing 制程不良 poor incoming part 来件不良 exposed metal/bare metal 金属裸露 excessive defect 过多的缺陷 critical defect 极严重缺陷 major defect 主要缺陷 minor defect 次要缺陷 not up to standard 不合规格 cosmetic defect 外观不良 lack of painting 烤漆不到位 slipped screw head/slippery slipped thread 滑丝 missing part 漏件 wrong part 错件 oxidation 氧化 defective threading 抽芽不良 poor staking 铆合不良 deficient purchase 来料不良 deficient manufacturing procedure 制程不良 cosmetic inspection 外观检查 inner parts inspection 内部检查 blister 气泡 angular offset 角度偏差 dent 压痕 scratch 刮伤 deformation 变形 filings 铁削 defective label 不良标签 abrasion 磨损 Breaking. (be)broken,(be)cracked 断裂short 射料不足 nick 缺口 speck 瑕疪 shine 亮班 splay 银纹 gas mark 焦痕 delaminating 起鳞 speckle 斑点 mildewed =moldy = mouldy 发霉 deformation 变形 burr(金属)flash(塑件)毛边 poor staking 铆合不良 excessive gap 间隙过大 grease/oil stains 油污 inclusion 杂质 shrinking/shrinkage 缩水 mixed color 杂色 fold of packaging belt 打包带折皱 painting make-up 补漆 discoloration 羿色 water spots 水渍 impurity 杂质 Mismatch 错位 failure, trouble 故障 deformation 变形 rust 生锈peel 脱漆 Shrink 缩水 Contamination 脏污 water spots 水渍 Gap 间隙 label error 标签错误 Missing label 漏贴rejection criteria 拒收标准 Suspected rejects 可疑庇 abrasion 损伤、磨损 Texture surface 印花纹表面 Streak 条纹 stains 污点 Blotch 斑点 discoloration 脱色 Inclusion 杂质 slug mark 压痕 dirt grime 灰尘 blush 毛边薄膜 sink 下凹 Hickey 漏漆 labels and logos 贴纸与商标 Configuration labels 组合贴纸 corrugated container 瓦摆纸箱 Delaminating 脱层splattering 散点Gouge 锉孔puckering。
电子行业英语词汇大全
《电子行业英语词汇大全》普特英语品质专业英语大全从事品质工作以来积累的常用英语，希望对有需要的朋友有所帮品质专业英语大全零件材料类的专有名词CPU：central processing unit(中央处理器)IC：Integrated circuit(集成电路)Memory IC：Memory Integrated circuit(记忆集成电路)RAM：Random Access Memory(随机存取存储器)DRAM：Dynamic Random Access Memory(动态随机存取存储器)SRAM：Staic Random Access Memory(静态随机存储器)ROM：Read-only Memory(只读存储器)EPROM：Electrical Programmable Read-only Memory(电可抹只读存诸器)EEPROM：Electrical Erasbale Programmable Read-only Memory(电可抹可编程只读存储器)CMOS：Complementary Metal-Oxide-Semiconductor(互补金属氧化物半导体)BIOS：Basic Input Output System(基本输入输出系统)Transistor：电晶体LED：发光二极体Resistor：电阻Variator：可变电阻Capacitor：电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器(ADP) Oscillator：频率振荡器(0sc) Crystal：石英振荡器XTAL/OSC：振荡产生器(X) Relay：延时器Sensor：感应器Bead core：磁珠Filter：滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子普特英语Oven：烤箱TFT：液晶显示器Oscilloscope：示波器Connector：连接器P CB：printed circuit board(印刷电路板)PCBA：printed circuit board assembly(电路板成品) PP：并行接口HDD：硬盘FDD：软盘PSU：power supply unit(电源供应器)SPEC：规格Attach：附件Case：机箱，盖子Cover：上盖Base：下盖Bazel：面板(panel) Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG：程序Barcode：条码System：系统System Barcode：系统条码M/B：mother board：主板CD-ROM：光驱FAN：风扇Cable：线材Audio：音效K/B：Keyboard(键盘) Mouse：鼠标Riser card：转接卡Card reader：读卡器普特英语Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE：集成电路设备，智能磁盘设备SCSI：小型计算机系统接口Gasket：导电泡棉AGP：加速图形接口PCI：周边组件扩展接口LAN：局域网USB：通用串形总线架构Slim：小型化COM：串型通讯端口LPT：打印口，并行口Power cord：电源线I/O：输入，输出Speaker：扬声器EPE：泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS：Quality system品质系统CS：Coutomer Sevice客户服务QC：Quality control品质管理IQC：Incoming quality control进料检验LQC：Line Quality Control生产线品质控制IPQC：In process quality control制程检验FQC：Final quality control最终检验普特英语OQC：Outgoing quality control出货检验QA：Quality assurance品质保证SQA：Source(supplier)Quality Assurance供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance制程品质保证QE：Quality engineer品质工程CE：component engineering零件工程EE：equipment engineering设备工程ME：manufacturing engineering制造工程TE：testing engineering测试工程PPE roduct Engineer产品工程IE：Industrial engineer工业工程ADM：Administration Department行政部RMA：客户退回维修CSDI：检修PC：producing control生管MC：mater control物管GAD：General Affairs Dept总务部A/D：Accountant/Finance Dept会计LAB：Laboratory实验室DOE：实验设计HR：人资PMC：企划RD：研发W/H：仓库SI：客验PD：Product Department生产部PA：采购(PUR：Purchaing Dept)SMT：Surface mount technology表面粘着技术MFG：Manufacturing制造MIS：Management information system资迅管理系统DCC：document control center文件管制中心厂内作业中的专有名词QT：Quality target品质目标QP：Quality policy目标方针QI：Quality improvement品质改善CRITICAL DEFECT：严重缺点(CR)MAJOR DEFECT：主要缺点(MA)MINOR DEFECT：次要缺点(MI)MAX：Maximum最大值MIN：Minimum最小值DIA iameter直径DIM imension尺寸LCL：Lower control limit管制下限普特英语UCL：Upper control limit管制上限EMI：电磁干扰ESD：静电防护EPA：静电保护区域ECN：工程变更ECO：Engineering change order工程改动要求(客户)ECR：工程变更需求单CPI：Continuous Process Improvement连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD：Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM：Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN：(试投产)FAI：首件检查FPIR：First Piece Inspection Report首件检查报告FAA：首件确认SPC：统计制程管制CP：capability index(准确度)CPK：capability index of process(制程能力) PMP：制程管理计划(生产管制计划)MPI：制程分析DAS efects Analysis System缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N：料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期M IL-STD：Military-Standard军用标准ICT：In Circuit Test(线路测试)ATE：Automatic Test Equipment自动测试设备MO：Manafacture Order生产单T/U：Touch Up(锡面修补)I/N：手插件普特英语P/T：初测F/T：Function Test(功能测试-终测)AS组立P/K：包装TQM：Total quality control全面品质管理MDA：manufacturing defect analysis制程不良分析(ICT) RUN-IN：老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM：Defect Part Per Million(不良率的一种表达方式：百万分之一)1000PPM即为0.1% Corrective Action：(CAR改善对策)ACC：允收REJ：拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession/Waive特采ISO：国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA：开箱稽核FIFO：先进先出PDCA：管理循环Plan do check action计划，执行，检查，总结WIP：在制品(半成品)S/O：Sales Order(业务订单)P/O：Purchase Order(采购订单)P/R：Purchase Request(请购单)AQL：acceptable quality level允收品质水准LQL；Limiting quality level最低品质水准QVL：qualified vendor list合格供应商名册AVL：认可的供货商清单(Approved Vendor List) QCD：Quality cost delivery(品质，交期，成本) MPM：Manufacturing project management制造专案管理KPI：Key performance indicate重要绩效指标MVT：Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL：ship to line(料到上线)NTF：No trouble found误判CIP：capacity improvement plan(产能改善计划) MRB：material review board(物料审核小组)MRB：Material reject bill退货单JIT：just in time(即时管理)5S：seiri seiton seiso seiketsu shitsuke(整理，整顿，清扫，清洁，修养)普特英语SOP：standard operation process(标准作业程序)SIP：Specification inspection process制程检验规范TOP：Test Operation Process(测试作业流程)WI：working instruction(作业指导书)SMD：surface mounting device(表面粘着原件)FAR：failure aualysis report故障分析报告CAR：Corrective action report改善报告BPR：企业流程再造(Business Process Reengineering) ISAR：首批样品认可(Initial Sample Approval Request)- JIT：实时管理(Just In Time)QCC：品管圈(Quality Control Circle)Engineering Department(工程部)TQEM：Total Quality Enviro nment Management(全面品质环境管理)PD：Production Department(制造)LOG：Logistics(后勤支持)Shipping：(进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB：Change Review Board(工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT：Quality Improvement Team品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S：Material Quality Feedback Sheet(来料品质回馈单) SCAR：Supplier Corrective Action Report(供货商改善对策报告) 8D Sheet：8 Disciplines sheet(8D单)PDCA：PDCA(Plan-Do-Check-Action)(管理循环)MPQ：Material Packing Quantity(物料最小包装量)DSCN：Delivery Schedule Change Notice(交期变更通知) QAPS：Quality Assurance Process Sheet(品质工程表)DRP：运销资源计划(Distribution Resource Planning)DSS：决策支持系统(Decision Support System)EC：电子商务(Electronic Commerce)EDI：电子资料交换(Electronic Data Interchange)EIS：主管决策系统(Excutive Information System)ERP：企业资源规划(Enterprise Resource Pla nning)FMS：弹性制造系统(Flexible Manufacture System)KM：知识管理(Knowledge Management)4L：逐批订购法(Lot-for-Lot)LTC：最小总成本法(Least Total Cost)LUC：最小单位成本(Least Unit Cost)普特英语MES：制造执行系统(Manufacturing Execution System) MPS：主生产排程(Master Production Schedule)MRP：物料需求规划(Material Requirement Planning) MRPⅡ：制造资源计划(Manufacturing Resource Planning) OEM：委托代工(Original Equipment Manufacture) ODM：委托设计与制造(Original Design&Manufacture) OLAP：线上分析处理(On-Line Analytical Processing) OLTP：线上交易处理(On-Line Transaction Processing) OPT：最佳生产技术(Optimized Production Technology) PDCA：PDCA管理循环(Plan-Do-Check-Action)PDM：产品数据管理系统(Product Data Management)) RCCP：粗略产能规划(Rough Cut Capacity Planning) SCM：供应链管理(Supply Chain Management)SFC：现场控制(Shop Floor Control)TOC：限制理论(Theory of Constraints)TQC：全面品质管制(Total Quality Control)FYI/R：for your information/reference仅供参考ASAP：尽快S/T：Standard time标准时间TPM：total production maintenance：全面生产保养ESD Wrist strap：静电环IT：information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer,Communication,Consumer electronic 消费性电子5W1H：When,Where,Who,What,Why,How 5M：Man,Machine,Material,Method,Measurement人,机器,材料,方法,测量4MIE：Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I：Manpower,Machine,Material,Method,Market,Management,Money,Information 人力，机器，材料，方法,市场，管理，资金，资讯普特英语1 Accuracy准确度2 Action行动3 Activity活动4 Analysis Covariance协方差分析5 Analysis of Variance方差分析6 Approved承认7 Attribute计数值8 Average平均数9 Balance sheet资产负债对照表10 Binomial二项分配11 Brainstorming Techniques脑力风暴法12 Cause and Effect Matrix因果图(鱼骨图)13 CL：Center Line中心线14 Check Sheets检查表15 Complaint投诉16 Conf ormity合格(符合)17 Control控制18 Control chart控制(管制)图19 Correction纠正20 Correlation Methods相关分析法21 CPI：continuouse Process Improvement连续工序改善22 Cross Tabulation Tables交叉表23 CS：Customer Sevice客(户)服(务)中心24 DSA：Defects Analysis System缺陷分析系统25 Data数据Description：品名26 DCC：Document Control Center文控中心27 Decision决策、判定28 Defects per unit单位缺点数29 Description描述30 Device装置31 Do执行32 DOE：Design of Experiments实验设计33 Element元素34 Engineering recbnology工程技35 Environmental环境36 Equipment设备37 Estimated accumulative frequency计算估计累计数38 EEquipment Variation设备变异39 External Failure外部失效,外部缺陷40 FA：Failure Analysis失效分析41 Fact control事实管理42 Fatigue疲劳43 FMEA：Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield(第一次通过)合格率普特英语45 FQA：Final Quality Assurance最终品质保证46 FQC：Final Quality control最终品质控制47 Gauge system测量系统48 Grade等级49 Histogram直方图50 Improvement改善51 Initial review先期审查52 Inspection检验53 Internal Failure内部失效、内部缺陷5 4IPQC：In Process Quality Control制程品质控制55 IQC：Incomming Quality Control来料品质控制56 IS International Organization for Standardization国际标准化组织57 LCL：Lower Control limit管制下限58 LQC：Line Quality Control生产线品质控制59 LSL：Lower Size Limit规格下限60 Machine机械61 Manage管理62 Materials物料63 Measurement测量64 Median中位数65 MSA：Measurement System Analysis测量系统分析66 Occurrence发生率67 Operation Instruction作业指导书68 Organization组织69 Parto柏拉图70 PPM arts per Million(百万分之)不良率71 Plan计划72 Policy方针73 Population群体74 PQA：Process Quality Assurance制程品质保证75 Practice实务(践)76 Prevention预防77 Probability机率78 Probability density function机率密度函数79 Procedure流程80 Process过程81 Process capability analysis制程能力分析(图)82 Process control and Process capability制程管制与制程能力83 Product产品84 Production生产85 Projects项目86 QA：Quality Assurance品质保证87 QC：Quality Control品质控制88 QE：Quality Engineering品质工程普特英语89 QFD：Quality Function Desgin品质机能展开(法)90 Quality质量91 Quality manu al品质手册92 Quality policy品质政策(质量方针)93 Random experiment随机试验94 Random numbers随机数95 R：Range全距(极差)96 Reject拒收97 Repair返修98 Repeatusility再现性99 Reproducibility再生性100 Requirement要求101 Responsibilities职责102 Review评审103 Reword返工104 Rolled yield直通率105 RPN：Risk Priority Number风险系数106 Sample抽样,样本107 Sample space样本空间108 Sampling with replacement放回抽样109 Sampling without replacement不放回抽样110 Scatter diagram散布图分析111 Scrap报废112 Simple random sampling简单随机取样113 Size规格114 SL：Size Line规格中心线115 Stratified random sampling分层随机抽样116 SOP：Standard Operation Procedure标准作业书117 SPC：Statistical Process Control统计制程管制118 Specification规范119 SQA：Source(Supplier)Quality Assurance供货商品质保证120 Stage sampling分段随机抽样121 Standard Deviation标准差122 Sum of squares平方和123 Taguchi-method田口(试验)方法124 Theory原理125 TQC：Total Quality Control全面品质控制126 TQM：Total Quality Management全面品质管理127 Traceablity追溯128 Training培训129 UCL：Upper Control Limit管制(控制)上限130 USL：Upper Size Limit规格上限131 Validation确认132 Variable计量值普特英语133 Verification验证134 Version版本135 VOC：Voice of Customer客户需求136 VOE：Voice of Engineer工程需求137 Inventory stock report：库存清单报告138 Sales order report：出货报告质量人员名称类QC quality control品质管理人员FQC final quality control终点质量管理人员IPQC in process quality control制程中的质量管理人员OQC output quality control最终出货质量管理人员IQC incoming quality control进料质量管理人员TQC total quality control全面质量管理POC passage quality control段检人员QA quality assurance质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering质量工程人员质量保证类FAI first article inspection新品首件检查FAA first article assurance首件确认CP capability index能力指数CPK capability process index模具制程能力参数SSQA standardized supplier quality audit合格供货商质量评估FMEA failure model effectiveness analysis失效模式分析FQC运作类AQL Acceptable Quality Level运作类允收质量水平S/S Sample size抽样检验样本大小ACC Accept允收REE Reject拒收CR Critical极严重的MAJ Major主要的MIN Minor轻微的Q/R/S Quality/Rel iability/Service质量/可靠度/服务P/N Part Number料号L/N Lot Number批号AOD Accept On Deviation特采UAI Use As It特采FPIR First Piece Inspection Report首件检查报告PPM Percent Per Million百万分之一制程统计品管专类普特英语SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计质量管理GRR Gauge Reproductiveness&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension尺寸DIA Diameter直径N Number样品数其它质量术语类QIT Quality Improvement Team质量改善小组ZD Zero Defect零缺点QI Quality Improvement质量改善QP Quality Policy目标方针TQM Total Quality Management全面质量管理RMA Return Material Audit退料认可7QCTools 7Quality Control Tools品管七大手法通用之件类ECN Engineering Change Notice工程变更通知(供货商) ECO Engineering Change Order工程改动要求(客户) PCN Process Change Notice工序改动通知PMP Product Management Plan生产管制计划SIP Standard Inspection Procedure制程检验标准程序SOP Standard Operation Procedure制造作业规范IS Inspection Specification成品检验规范BOM Bill Of Material物料清单PS Package Specification包装规范SPEC Specification规格DWG Drawing图面系统文件类ES Engineering Standard工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard工艺标准ISO International Standard Organization国际标准化组织GS General Specification一般规格部类PMC Production&Material Control生产和物料控制PCC Product control center生产管制中心PPC Production Plan Control生产计划控制MC Material Control物料控制DC Document Center资料中心QE Quality Engineering质量工程(部)QA Quality Assurance质量保证(处)普特英语QC Quality Control质量管理(课)PD Product Department生产部LAB Laboratory实验室IE Industrial Engineering工业工程R&D Research&Design设计开发部生产类PCs Pieces个(根,块等)PRS Pairs双(对等)CTN Carton卡通箱PAL Pallet/skid栈板PO Purchasing Order采购订单MO Manufacture Order生产单D/C Date Code生产日期码ID/C Identification Code(供货商)识别码SWR Special Work Request特殊工作需求L/N Lot Number批号P/N Part Number料号OEM Original Equipment Manufacture原设备制造PC Personal Computer个人计算机CPU Central Processing Unit中央处理器A.S.A.P As Soon As Possible尽可能快的E-MAIL Electrical-Mail电子邮件N/A Not Applicable不适用QTY Quantity数量I/O input/output输入/输出NG Not Good不行,不合格C=0 Critical=0极严重不允许APP Approve核准,认可,承认CHK Check确认ASS'Y Assembly装配,组装T/P True Position真位度5WIH When,Where,Who,What,Why,How to 6MMan,Machine,Material,Method,Measurement,Message 4MTHMan,Material,Money,Method,Time,How人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance策略质量保证DQA Design Quality Assurance设计质量保证MQA Manufacture Quality Assurance制造质量保证SSQA Sales and service Quality Assurance销售及服务质量保证LRR Lot Reject Rate批退率SPS Switching power supply电源箱DT Desk Top卧式(机箱)MT Mini-Tower立式(机箱)DVD Digital Video Disk普特英语VCD Video Compact Disk LCD Liquid Crystal Display CAD Computer Aided Design CAM Computer Aided Manufacturing CAE Computer Aided Engineering PCB Printed Circuit Board印刷电路板CAR Correction Action Report改善报告NG Not Good不良WDR Weekly Delivery Requirement周出货要求PPM Percent Per Million百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requirement Planning物料需计划OS Operation System操作系统TBA To Be Assured待定,定缺D/C Drawing Change P/P Plans&Procedure EMI Electrical-Music Industry电子音乐工业Electrical Magnetic Interference电子干扰RFI Read Frequency Input读频输入MMC Maximum Material Condition MMS Maximum Material Size LMC Least Material Condition LMS Least Material Size LED lighting-emitting diode发光二极管QBR Quarter Business Record CIP Continuous improvement process FGI Forecasted Goal Inventory CNC Computerized numeral controller B2C Business to customer B2B Business to business AVL Approved vendor list POP Procedure of packaging EOL End of life VDCS Vender defect correcting sheet PDCS Process defect correcting sheet GRN Goods receiving note A/R Accounting receivable A/P Accounting payable专业词汇通用类president董事长operator作业员普特英语position职务general manager总经理special assistant特助deputy manager|'depjuti|=vice manager副理deputy supervisor=vice supervisor副课长group leader组长line leader线长supervisor课长responsible department负责单位Human Resources Department人力资源部Head count人数p roduction department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management颜色管理Visual management目视管理production capacity生产力first count初盘first check初盘复棹second count复盘second check复盘复核quantity of physical inventory second count复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification规格普特英语model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume,consumption消耗to notify通知to fill in填写to collect,to gather收集statistics统计cosmetic inspection standard外观检验规范computer case计算机外壳(组件)per sonal computer enclosure计算机机箱产品front plate前板rear plate后板chassis|'∫.si|基座bezel panel面板Hood上盖base pan基座bezel面板riser card扩充卡flat cable排线TOP driver cage上磁架bottom driver cage下磁架resin film树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts=buffer备品plastic parts塑料件sheet metal parts/stamping parts冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺普特英语plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise,modify修订to switch over to,switch-to,switching over切换engineering bottleneck,project difficulty工程瓶颈glove(s)手套glove(s)with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean atable擦桌子air pipe气管delivery deadline交货期die worker模工production,to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler天车trailer=long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing=containerization装箱velocity速度patent专利普特英语coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change换模to fix adie装模to repair adie修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板(顶板)top block上垫脚普特英语stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch=stinger加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate=plate pinch压板thickness gauge厚薄规cutting die,blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate,front board模板padding block垫块stepping bar垫条panel board镶块to load adie装上模具to unload adie御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板普特英语spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch=die button圆冲子shape punch=die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score=groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒普特英语pin销lifter guide pin浮升导料销guide pin导正销wire sp ring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue,cont.连动to grip(material)吸料location lump,locating piece,location block定位块reset复位to file burr锉毛刺embedded lump|in'bed|mp|镶块∧|l stamping-missing漏冲to tight abolt拧紧螺栓to loosen abolt拧松螺栓punched hole冲孔to cut edge=side cut=side scrap切边to bending折弯to pull,to stretch拉伸engraving,to engrave刻印stamping油印to stake铆合designing,to design设计design modification设计修改成gauge(or jig)治具pedal踩踏板普特英语stopper阻挡器flow board流水板torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed st eel钼高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印冲压类punch,press冲punching machine冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping,press冲压feeder送料机rack,shelf,stack料架taker取料机to reverse material翻料to load material上料to unload material卸料to return material/stock to退料scraped|'skr.pid|报废普特英语scrape.v.刮；削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod(bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口普特英语。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
品质人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size。