单片机万年历程序..

单片机万年历程序#include <reg52.h> //调用单片机头文件#define uchar unsigned char //无符号字符型宏定义变量范围0~255 #define uint unsigned int //无符号整型宏定义变量范围0~65535 #include "eeprom52.h"#include "nongli.h"bit flag_200ms ;bit flag_100ms ;sbit beep = P3^7; //蜂鸣器定义bit flag_beep_en;uint clock_value; //用作闹钟用的sbit dq = P3^1; //18b20 IO口的定义uint temperature ; //温度变量uchar flag_nl; //农历阳历显示标志位uchar menu_1,menu_2;uchar key_time,flag_value; //用做连加的中间变量bit key_500ms ;uchar n_nian,n_yue,n_ri; //农历显示的函数#include "ds1302.h"#include "lcd1602.h"/******************把数据保存到单片机内部eeprom中******************/ void write_eeprom(){SectorErase(0x2000);byte_write(0x2000, fen1);byte_write(0x2001, shi1);byte_write(0x2002, open1);byte_write(0x2058, a_a);}/******************把数据从单片机内部eeprom中读出来*****************/ void read_eeprom(){fen1 = byte_read(0x2000);shi1 = byte_read(0x2001);open1 = byte_read(0x2002);a_a = byte_read(0x2058);}/**************开机自检eeprom初始化*****************/void init_eeprom(){read_eeprom(); //先读if(a_a != 1) //新的单片机初始单片机内问eeprom{fen1 = 3;shi1 = 8;open1 = 1;a_a = 1;write_eeprom(); //保存数据}}/***********************18b20初始化函数*****************************/ void init_18b20(){bit q;dq = 1; //把总线拿高delay_uint(1); //15usdq = 0; //给复位脉冲delay_uint(80); //750usdq = 1; //把总线拿高等待delay_uint(10); //110usq = dq; //读取18b20初始化信号delay_uint(20); //200usdq = 1; //把总线拿高释放总线}/*************写18b20内的数据***************/void write_18b20(uchar dat){uchar i;for(i=0;i<8;i++){ //写数据是低位开始dq = 0; //把总线拿低写时间隙开始dq = dat & 0x01; //向18b20总线写数据了dq = 1; //释放总线dat >>= 1;}}/*************读取18b20内的数据***************/uchar read_18b20(){uchar i,value;for(i=0;i<8;i++){dq = 0; //把总线拿低读时间隙开始value >>= 1; //读数据是低位开始dq = 1; //释放总线if(dq == 1) //开始读写数据value |= 0x80;delay_uint(5); //60us 读一个时间隙最少要保持60us的时间}return value; //返回数据}/*************读取温度的值读出来的是小数***************/uint read_temp(){uint value;uchar low; //在读取温度的时候如果中断的太频繁了，就应该把中断给关了，否则会影响到18b20的时序init_18b20(); //初始化18b20write_18b20(0xcc); //跳过64位ROMwrite_18b20(0x44); //启动一次温度转换命令init_18b20(); //初始化18b20write_18b20(0xcc); //跳过64位ROMwrite_18b20(0xbe); //发出读取暂存器命令EA = 0;low = read_18b20(); //读温度低字节value = read_18b20(); //读温度高字节EA = 1;value <<= 8; //把温度的高位左移8位value |= low; //把读出的温度低位放到value的低八位中value *= 0.625; //转换到温度值小数return value; //返回读出的温度带小数}/******************1ms 延时函数*******************/void delay_1ms(uint q){uint i,j;for(i=0;i<q;i++)for(j=0;j<120;j++);}/******************写星期函数*******************/void write_week(uchar hang,uchar add,uchar week)//写星期函数{if(hang==1)write_com(0x80+add);elsewrite_com(0x80+0x40+add);switch(week){case 1:write_data('M');//星期数为1时，显示write_data('O');write_data('N');break;case 2:write_data('T');//星期数据为2时显示write_data('U');write_data('E');break;case 3:write_data('W');//星期数据为3时显示write_data('E');write_data('D');break;case 4:write_data('T');//星期数据为4是显示write_data('H');write_data('U');break;case 5:write_data('F');//星期数据为5时显示write_data('R');write_data('I');break;case 6:write_data('S');//星期数据为6时显示write_data('T');write_data('A');break;case 0:write_data('S');//星期数据为7时显示write_data('U');write_data('N');break;}}/*************时钟显示***************/void init_1602_ds1302(){write_sfm2_ds1302(1,1,shi); //显示时write_sfm2_ds1302(1,4,fen); //显示分write_sfm2_ds1302(1,7,miao); //显示秒write_week(2,12,week);// write_sfm1(1,14,week); //显示星期write_sfm3_18B20(1,11,temperature); //显示温度if(flag_nl == 0) //显示阳历{write_sfm2_ds1302(2,2,nian); //显示年write_sfm2_ds1302(2,5,yue); //显示月write_sfm2_ds1302(2,8,ri); //显示日}else //显示农历{write_sfm2_ds1302(2,2,n_nian); //显示年write_sfm2_ds1302(2,5,n_yue); //显示月write_sfm2_ds1302(2,8,n_ri); //显示日}}/*************定时器0初始化程序***************/void init_time0(){EA = 1; //开总中断TMOD = 0X01; //定时器0、工作方式1ET0 = 1; //开定时器0中断TR0 = 1; //允许定时器0定时}/*************闹钟报警函数***************/void menu_dis(){static uchar mm,value;if(flag_100ms == 1) //100ms执行一次{flag_100ms = 0;if(open1 == 1) //如果闹钟打开{if((miao == 0) && (fen == fen1) && (shi == shi1)){flag_beep_en = 1; //有报警打开蜂鸣器响的标志位}if(flag_beep_en == 1) //闹钟以被打开。

{clock_value++;if(clock_value <= 30)beep = ~beep; //蜂鸣器叫3秒else if(clock_value > 30){beep = 1; //蜂鸣器停1秒if(clock_value > 40){clock_value = 0;}}// 1 分钟后自动关闭闹钟value ++;if(value >= 10){value = 0;mm++;if(mm >= 60){mm = 0;flag_beep_en = 0;beep = 1;}}}}}}。