道康宁syl-off R 7020 coating

合集下载

道康宁dc791硅酮耐候密封胶

若道康宁违反该保证，您所能获得的补偿，仅限于退还购货价款或替换不符合保证的任何产品。
在适用法律允许的最大限度内，道康宁特别声明，不作针对特定目的适用性或适销性的任何其他明示或暗示的保证。
道康宁791硅酮耐候密封胶符合甚至超越下列标准规范： ASTM C-920 S 类，NS 型，50
可能渗出油、可塑剂、溶剂的建材表面上，或部分硫化橡胶垫片或胶带。
道康宁声明，不对任何间接或附带性的损害承担责任。
级，适用于NT, M, G, A, 类应用 ISO11600 F G-25LM JC/T 882-2001 I 25LM GB/T 14683-2003 B G, F 25LM KS F4910-2010 F-25LM EN15651-1/2:2012
性材料表面，可能需要上底漆以确道康宁791 硅酮耐候密封胶以300
不得被视为侵犯任何专利权的导因。
保良好的粘结性，道康宁建议在工程开工前都应做粘结性测试。将道康宁791硅酮耐候密封胶连续不断
毫升胶管包装及500毫升肠状铝箔包装方式提供给客户。请和当地的道康宁销售处联系来获取有关信
道康宁的唯一保证，是产品满足发货时有效的道康宁销售规格。
发有机物含量。要获得不同颜色的最大可挥发有机物含量信息，请发邮件到 product.inquiry@.
产品说明
金属灰、古铜、岩灰、瓷白和白色。本产品未被测试或陈述为适用于医
道康宁 791 硅酮耐候密封胶是一种单组份，不垂流，中性固化密封胶，在大部分外界环境温度下能轻易地挤出使用，并借助于空气中的水份，
道康宁销售应用工程师或分销商处的道康宁代表。
获得，或者致电道康宁全球联络处.。
有限保证信息—请仔细阅读

Dow Corning SE 9187L 黑色、透明或白色液体防腐剂说明书

SE 9187L BLK SE 9187L BLK SE 9187L CLR SE 9187L CLRProduct InformationElectronicsDow Corning ®SE 9187 L Black, Clearor White Adhesivecure∙Very low viscosity∙Controlled silicone volatility ∙UL 94HB (black and white only)∙Room temperature cure, no ovens required∙Faster in-line processing at room temperature with option for heat acceleration∙Excellent flow, fill or self-leveling after dispensing∙Reduced potential for silicone volatiles∙Cures to soft, low stress elastomer/ Soft coating can improve reliability against stress∙1-part, black, translucent, or white ∙Polydimethylsiloxane1-part, black, clear (translucent)or white, fast tack-free,controlled volatility adhesive with very low viscosity APPLICATIONSDow Corning ®SE 9187 L Black, Clear or White Adhesive is suitable for:∙Display module assembly∙PCB protection (Conformal Coating)∙General pottingTYPICAL PROPERTIESSpecification Writers: These values are not intended for use in preparingspecifications. Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.DESCRIPTIONDow Corning® brand one-part moisture cure adhesives are generally cured at room temperature and in an environment of 30 to 80 percent relative humidity eliminating the need for curing ovens and the associated costs of energy and capital. Greater than 90 percent of full physical properties should be attained within 24 to 72 hours and varies according to product. Faster manufacturing throughput can be achieved since the adhesive and component can be handled in much shorter times of about 10 to 120 minutes, depending on the adhesive selected and the amount applied. These adhesives are not typically used in highly confined spaces or where a deep section cure is required as they generally cure from the exposed surface inward at a rate of 0.25 inch per seven days. Cure progresses from the outer exposed surface and is dependent on the moisture in the air. Working time is generally a few minutes to an hour for these products until a surface skin begins to form. Mild heat below 60°C (140°F) may be used to increase through-put by accelerating the cure. Dow Corning® brand silicone adhesives retain their original physical and electrical properties over a broad range of operating conditions which enhance the reliability of and service life of electronic devices.The stable chemistry and versatile processing options of these adhesives offer benefits for a variety of electronics needs from increasing component safety and reliability, reducing total cost or increasing the performance envelope of devices or modules. APPLICATION METHODS Automated or manual needledispensing systems PACKAGING INFORMATIONMultiple packaging sizes are available for this product. Please contact your local distributor or Dow Corning representative for information on packaging size and ABLE LIFE ANDSTORAGEFor best results, Dow Corning RTVadhesives should be stored at or belowthe storage temperature listed on theproduct label. Special precautionsmust be taken to prevent moisturefrom contacting these materials.Containers should be kept tightlyclosed with head or air spaceminimized. Partially filled containersshould be purged with dry air or othergases, such as nitrogen. The productshould be stored in its originalpackaging with the cover tightlyattached to avoid any contamination.Store in accordance with any specialinstructions listed on the product label.The product should be used by its UseBefore date as indicated on theproduct label.PREPARING SURFACESAll surfaces should be thoroughlycleaned and/or degreased withDow Corning®brand OS Fluids,naphtha, mineral spirits, methyl ethylketone (MEK) or other suitablesolvent. Solvents such as acetone orisopropyl alcohol (IPA) do not tend toremove oils well, and any oilsremaining on the surface may interferewith adhesion. Light surface abrasionis recommended whenever possible,because it promotes good cleaning andincreases the surface area for bonding.A final surface wipe with acetone orIPA is also useful. Some cleaningtechniques may provide better resultsthan others; users should determinethe best techniques for their particularapplications.SUBSTRATE TESTINGDue to the wide variety of substratetypes and differences in substratesurface conditions, general statementson adhesion and bond strength areimpossible. To ensure maximum bondstrength on a particular substrate,cohesive failure of the product in a lapshear or similar test is needed toensure compatibility of the adhesivewith the substrate being considered.Also, this test can be used todetermine minimum cure time or todetect the presence of surfacecontaminants such as mold releaseagents, oils, greases and oxide films.ADHESIONDow Corning silicone adhesives arespecially formulated to provideunprimed adhesion to many reactivemetals, ceramics and glass, as well asto selected laminates, resins andplastics. However, good adhesioncannot be expected on non-reactivemetal substrates or non-reactiveplastic surfaces such as Teflon®,polyethylene or polypropylene.Special surface treatments such aschemical etching or plasma treatmentcan sometimes provide a reactivesurface and promote adhesion to thesetypes of substrates. Dow Corning®brand Primers can be used to increasethe chemical activity on difficultsubstrates. Poor adhesion may beexperienced on plastic or rubbersubstrates that are highly plasticized,because the mobile plasticizers act asrelease agents. Small-scale laboratoryevaluation of all substrates isrecommended before production trialsare made.USEFUL TEMPERATURERANGESFor most uses, silicone adhesivesshould be operational over atemperature range of -45 to 200°C(-49 to 392°F) for long periods oftime. However, at both the low-andhigh temperature ends of thespectrum, behavior of the materialsand performance in particularapplications can become morecomplex and require additionalconsiderations. For low-temperatureperformance, thermal cycling toconditions such as -55°C(-67°F) maybe possible, but performance shouldbe verified for your parts orassemblies.Factors that may influenceperformance are configuration andstress sensitivity of components,cooling rates and hold times, and priortemperature history. At the high-temperature end, the durability of thecured silicone elastomer is time andtemperature dependent. As expected,the higher the temperature, the shorterDow Corning is a registered trademark of Dow Corning Corporation.the time the material will remain useable.SOLVENT EXPOSUREThe silicone adhesive discussed in this literature is intended only to survive splash or intermittent exposures. It is not suited for continuous solvent or fuel exposure. Testing should be done to confirm performance of the adhesives under these conditions. HANDLING PRECAUTIONSPRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND MATERIAL SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. THE MATERIAL SAFETY DATA SHEET IS AVAILABLE ON THE DOW CORNING WEBSITE AT , OR FROM YOUR DOW CORNING SALES APPLICATION ENGINEER, OR DISTRIBUTOR, OR BY CALLING DOW CORNING CUSTOMER SERVICE.LIMITATIONSThis product is neither tested nor represented as suitable for medical or pharmaceutical uses.HEALTH AND ENVIRONMENTAL INFORMATIONTo support customers in their product safety needs, Dow Corning has an extensive Product Stewardship organization and a team of Product Safety and Regulatory Compliance (PS&RC) specialists available in each area.For further information, please see our website, or consult your local Dow Corning representative.LIMITED WARRANTYINFORMATION–PLEASEREAD CAREFULLYThe information contained herein isoffered in good faith and is believed tobe accurate. However, becauseconditions and methods of use of ourproducts are beyond our control, thisinformation should not be used insubstitution for customer’s tests toensure that our products are safe,effective, and fully satisfactory for theintended end use. Suggestions of useshall not be taken as inducements toinfringe any patent.Dow Corning’s sole warranty is thatour products will meet the salesspecifications in effect at the time ofshipment.Your exclusive remedy for breach ofsuch warranty is limited to refund ofpurchase price or replacement of anyproduct shown to be other than aswarranted.TO THE FULLEST EXTENTPERMITTED BY APPLICABLELAW, DOW CORNINGSPECIFICALLY DISCLAIMSANY OTHER EXPRESS ORIMPLIED WARRANTY OFFITNESS FOR A PARTICULARPURPOSE ORMERCHANTABILITY.DOW CORNING DISCLAIMSLIABILITY FOR ANYINCIDENTAL ORCONSEQUENTIAL DAMAGES.HOW CAN WE HELP YOUTODAY?Tell us about your performance,design and manufacturing challenges.Let us put our silicon-based materialsexpertise, application knowledge andprocessing experience to work foryou.For more information about ourmaterials and capabilities, visit.To discuss how we could worktogether to meet your specific needs,email **************************or go to /contactusfor a contact close to your location.Dow Corning has customer serviceteams, science and technology centers,application support teams, salesoffices and manufacturing sites aroundthe globe.We help you invent the future.™Dow Corning is a registered trademark of Dow Corning Corporation.SE 9187L BLK SE 9187L BLK SE 9187L CLR SE 9187L CLR。

成功的离型剂解决方案

如果您需要涂敷一种特殊的底材，则表2将告诉您一般来说哪个系列最适合这种底材。
如果您对离型剂的选择取决于应用，则表3将帮助您做出适合的匹配。
如果您的离型剂必须采用一种特殊的粘合剂，则表4将为您指示最相容的离型剂系列。
如果您的应用对剥离力与剥离速度有着精确的要求，则图1至3将帮助您确定具有适合的性能属性的离型剂产品系列。
5. 离型剂是否将用于标签、胶带、合成品或食品接触等应用？
6. 您的离型剂将使用哪种粘合剂？
7. 您对剥离速度范围内的剥离力有何要求？
将这些问题对照下面的图、表将帮助您缩小搜索的范围。
表1.
加工设备的相容性
输送系统无溶剂溶剂型乳液型
常规
涂敷设备
常规设备包括麦耶杆、直接凹板、空气刀、挤压辊、
与溶剂型和乳液型离型剂不同的是，它们不含那些必须除去的载体。因此，可以实现更快的线速度。这些离型剂最适合用于具有光滑表面的砑光或涂层纸和薄膜上，因为它们在多孔纸上具有吸收的潜力。与溶剂型离型剂相比，无溶剂离型剂不易损坏薄膜，但可能需要进行电晕处理或使用添加剂才能达到相同的附着水平。无溶剂离型剂的主要缺点为需要使用精密涂敷设备（如三辊偏置差异凹板或多辊光滑辊涂敷滚筒）才能达到所需的低涂覆量，满足经济剥离衬垫的需要。
美中不足的是，涂敷线速度越快，涂层头部形成有机硅薄雾的可能性也就越大。虽然任何离型剂和任何涂敷滚筒在某些线速度都可能形成有机硅薄雾，但无溶剂型离型剂的问题最为普遍。
为此，道康宁引入了Syl-Off ®品牌一种无溶剂高速交联剂系列，它能显著减少涂层头部的薄雾。这一系列中包括一种Syl-Off ®优势系列高速交联剂，可以在那些需要优先控制成本的运行中减少薄雾、达到破记录的线速度。这种交联剂是专门为配合优势系列低铂离型剂而设计的。

道康宁产品Q2-5211

下，道康宁® Q2-5211超级润湿剂可将表面张力降低至23达因/厘米以下（见表1），在叶面蜡质层等难于润湿的表面实现极快的润湿
和分散,从而，使除草剂、杀虫剂、杀真菌剂和其他农药达到完全的
覆盖。
除快速润湿和分散外，道康宁® Q2-5211超级润湿剂还能大大提高植物组织对农药的摄取。在除草剂桶混时加入道康宁® Q2-5211超级润湿剂可显著提高润湿效率，特别是应用水溶性除草剂在阔叶草控制。快速摄取可产生“耐雨性”— —由于除草剂已渗透到植物内部组织，因而不会被雨水冲刷。图1、 2、3显示道康宁® Q2-5211超级润湿剂在温室试验中对低浓度 Roundup Classic®2和Blazer®3除草剂所起的效果。
道康宁的唯一保证，是产品满足发货时的道康宁销售说明。
若道康宁违反该保证，您所能获得的补偿仅限于退还购货价款或替换不符合保证的任何产品。
道康宁特别声明，不作任何其他明示或暗示对特定目的适用性或适销性的保证。
道康宁声明不对任何间接或附带性的损害负责。
图 1 表面活性剂对 Blazer 杀虫剂在绒毛叶上活性的影响
有关详情，请登陆或咨询当地的道康宁销售代表。
有限保证信息–请仔细阅读
此处提供的信息准确无误。然而，由于使用本公司产品的条件和方法非我们所能控制，本信息不能取
代客户为确保道康宁产品安全、有效，并完全满足于特定的最终用途而进行的测试。我们所提供的使用建议，不得被视为侵犯任何专利权的导因。
8.7
1.9
0.025％水溶液在 25℃（77ºF）.........
35.9
17.0
PE 润湿半径，0.2 毫升液滴
PE 表面能:22 达因，厘米

Dow Corning 品牌胶水封装剂双部分室温潮湿愈合类说明书

Information About Dow Corning ® brand Adhesive/SealantsSilicones and ElectronicsLong-term, reliable protection of sensitive circuits and components is important in many of today’s delicate and demanding electronic applications. Silicones function as durable dielectric insulation, as barriers against environmental contaminants and as stress-relieving shock and vibration absorbers over a wide temperature and humidity range.In addition to sustaining their physical and electrical prop-erties over a broad range of operating conditions, silicones are resistant to ozone and ultraviolet degradation, have good chemical stability and are available in a variety of useful forms as conformal coatings, encapsulants and adhesives.Dow Corning’s broad range of general purpose and specialty products offers you a choice of materials for your application needs.Dow Corning offers a variety of noncorrosive silicone products for electronic sealing, bonding and adhering applications. These adhesives generally fall into three cure types. The first group are moisture cure, generally meant for room-temperature processing. The second type(condensation cure) offers rapid room-temperature and deep-section curing. The third type is heat cure for rapid processing. All convert to durable, relatively low stresselastomers. Most will develop good, primerless adhesion to a variety of common substrates including ceramics, reactive metals and filled plastics.TYPICAL PROPERTIESThese values are not intended for use in preparing speciﬁcations.Speciﬁcation Writers: Please obtain copies of the Dow Corning Sales Speciﬁcations for these products and use them as a basis for your speciﬁcations. They may be obtained from any Dow Corning Sales Ofﬁce, or from Dow Corning Customer Service in Midland,MI. Call (517) 496-6000.HEAT CURE TIMESCURE CONDITIONSOne-Part Moisture Cure RTVThe one-part moisture cure adhesives (838, 839, 3165, 3145,3140 and 3-1744) are generally cured at room temperature and in a range of 30 to 80 percent relative humidity. Greater than 90 percent of their full physical properties should be attained within 24 to 72 hours depending on the product chosen. Materials and parts can be handled in much shorter times of about 10 to 120 minutes depending on the product chosen and the amount of material used per part. These materials are not typically used for highly confined or deep section cures. Materials will generally cure about 0.25 inch per seven days from any exposed surface. Cure progresses from the outer surface and is dependent on the moisture in the air. Working time is generally a few minutes to an hour for these products until a surface skin begins to form. Mild heat acceleration of the cure rate may be possible but temperatures above 60°C (140°F) are not recommended.Two-Part Room Temperature Condensation CureDow Corning ® Q3-6093 Silicone Adhesive is the only two-part condensation curing product. Once mixed, cure progresses rapidly at room temperature. Good strength is attained within an hour but full properties are not reached for anumber of days. Q3-6093 adhesive contains its own source of moisture and cure progresses evenly throughout the material.Deep section or confined cures are possible however (see “Reversion”). Working time is only a few minutes.Heat CureThe addition curing adhesives (577, 3-6876, 3-6611 and 3-6265) should be cured at 100°C (212°F) or above. The cure rate is rapidly accelerated with heat (see cure schedulesin table). For thicker sections or if voiding is observed, a 30 minutes pre-cure at 70°C (158°F) may reduce voids in the elastomer. Addition-curing materials contain all the ingredients needed for cure with no byproducts from the cure mechanism. Deep section or confined cures arepossible. Cure progresses evenly throughout the material.These adhesives generally have long working times.PREPARING SURFACESAll surfaces should be thoroughly cleaned and/or degreased with Dow Corning ®brand OS Fluids, naphtha, mineral spirits,methyl ethyl ketone (MEK) or other suitable solvent.Solvents such as acetone or isopropyl alcohol (IPA) do not tend to remove oils well, and any oils remaining on the surface may interfere with adhesion. Light surface abrasion is recommended whenever possible, because it promotes good cleaning and increases the surface area for bonding. A final surface wipe with acetone or IPA is also useful.Different cleaning techniques may give better results than others. Users should determine the best techniques for their applications.ADHESIONDow Corning silicone adhesives are specially formulated to provide unprimed adhesion to many reactive metals,ceramics and glass, as well as to selected laminates, resins and plastics. However, good adhesion cannot be expected on nonreactive metal substrates or non-reactive plastic surfaces such as Teflon ®, polyethylene or polypropylene. Special surface treatments such as chemical etching or plasma treatment can sometimes provide a reactive surface and promote adhesion to these types of substrates. Dow Corning ®brand primers (see “Primer Selection Guide”) can be used to increase the chemical activity on difficult substrates.2P5200 Red is a low-VOC alternative to 1200 Red.3P5204 is a low-VOC alternative to 1204.4The lower VOC value is for states and air quality management districts that have recognized volatile methylsiloxanes as VOC exempt.PRIMER SELECTION GUIDEThese values are not intended for use in preparing specifications.Poor adhesion may be experienced on plastic or rubber substrates that are highly plasticized, because the mobile plasticizers act as release agents. Small-scale laboratory evaluation of all substrates is recommended before production trials are made.In general, increasing the cure temperature and/or cure time will improve the ultimate adhesion.SUBSTRATE TESTINGDue to the wide variety of substrate types and differences in substrate surface conditions, general statements on adhesion and bond strength are impossible. To ensure maximum bond strength on a particular substrate, 100 percent cohesive failure of the adhesive in a lap shear or similar adhesive strength test is desired. This ensures compatibility of the adhesive with the substrate being considered. Also,this test can be used to determine minimum cure time or can detect the presence of surface contaminants such as mold release agents, oils, greases and oxide films.USEFUL TEMPERATURE RANGESFor most uses, silicone elastomers should be operational over a temperature range of -45 to 200°C (-49 to 392°F) for long periods of time. However, at both the low and high temperature ends of the spectrum, behavior of the materials and performance in particular applications can become more complex and require additional considerations.For low-temperature performance, thermal cycling to conditions such as -55°C (-67°F) may be possible, butperformance should be verified for your parts or assemblies.Factors that may influence performance are configuration and stress sensitivity of components, cooling rates and hold times, and prior temperature history.At the high-temperture end, the durability of the cured silicone elastomer is time and temperature dependent. As expected, the higher the temperature, the shorter the time the material will remain useable.COMPATIBILITYCertain materials, chemicals, curing agents and plasticizers can inhibit the cure of addition cure adhesives. Most notable of these include:•Organotin and other organometallic compounds •Silicone rubber containing organotin catalyst •Sulfur, polysulfides, polysulfones or other sulfur-containing materials•Amines, urethanes or amine-containing materials •Unsaturated hydrocarbon plasticizers •Some solder flux residuesIf a substrate or material is questionable with respect to potentially causing inhibition of cure, it is recommended that a small scale compatibility test be run to ascertain suitability in a given application. The presence of liquid or uncured product at the interface between the questionable substrate and the cured gel indicates incompatibility and inhibition of cure.MIXING AND DE-AIRINGUpon standing, some filler may settle to the bottom of the liquid containers after several weeks. To ensure a uniform product mix, the material in each container should be thoroughly mixed prior to use.1Clear only.2Gray only.3UL746C Approved.LISTINGS AND SPECIFICATIONSDow Corning Corporation Midland, Michigan 48686-0994Dow Corning and Sylgard are registered trademarks of Dow Corning Corporation.Teflon is a registered trademark of E.I. du Pont de Nemours Co.©2000 Dow Corning Corporation. All rights reser ved.Printed in USAAGP4781Form No. 10-911A-01Two-part materials should be mixed in the proper ratio (1:1or 10:1) either by weight or volume. The presence of light colored streaks or marbling indicates inadequate mixing.Automated airless dispense equipment can be used toreduce or avoid the need to de-air. If de-airing is required to reduce voids in the cured elastomer, consider a vacuum de-air schedule of >28 inches Hg for 10 minutes or until bubbling subsides.REVERSIONWhen two-part condensation curing materials with organo-tin catalysts, such as Q3-6093 adhesive, are cured in confinement (especially in deep section) and are later subjected to high heat conditions, can potentially revert back from a cured elastomer to a flowable polymer.Although this condition is unusual, parts using Q3-6093adhesive should be thoroughly tested in accelerated temperature conditions for this potential limitation.SOLVENT EXPOSUREWhen liquid or vapor solvent or fuel exposure can occur in an application, the silicone adhesives discussed in thisbrochure are intended only to survive splash or intermittent exposures. They are not suited for continuous solvent or fuel exposure. Testing should be done to confirm performance of the adhesives under these conditions.STORAGE AND SHELF LIFEShelf life is indicated by the “Use Before” date found on the product label.For best results, Dow Corning RTV adhesives should be stored at or below 25°C (77°F). Special precautions must be taken to prevent moisture from contacting these materials.Containers should be kept tightly closed and head or air space minimized. Partially filled containers should be purged with dry air or other gases, such as nitrogen.Dow Corning heat-cure adhesives should also be stored at or below 25°C (77°C). Containers should be kept tightly closed and kept in cold storage at all times to extend shelf life.LIMITATIONSThese products are neither tested nor represented as suitable for medical or pharmaceutical uses.PACKAGINGIn general, Dow Corning adhesives/sealants are supplied in nominal 0.45-, 3.6-, 18- and 200-kg (1-, 8-, 40- and 440-lb)containers,net weight. Not all products may be available in all packages and some additional packages, such as a bladder packs or tubes, may be available for certain coatings and package sizes.SAFE HANDLING INFORMATIONPRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED. BEFORE HANDLING,READ PRODUCT AND MATERIAL SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. THE MATERIAL SAFETY DATA SHEET IS AVAILABLE FROM YOURDOW CORNING REPRESENTATIVE, OR DISTRIBUTOR,OR BY WRITING TO DOW CORNING CUSTOMER SERVICE, OR BY CALLING (517) 496-6000.WARRANTY INFORMATION – PLEASE READ CAREFULLYThe information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control,this information should not be used in substitution for customer’s tests to ensure that Dow Corning’s products are safe, effective, and fully satisfactory for the intended end use. Dow Corning’s sole warranty is that the product will meet the Dow Corning sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replace-ment of any product shown to be other than as warranted.Dow Corning specifically disclaims any other express or implied warranty of fitness for a particular purpose or merch-antability. Unless Dow Corning provides you with a specific,duly signed endorsement of fitness for use, Dow Corning disclaims liability for any incidental or consequential damages.Suggestions of uses should not be taken as inducements to infringe any particular patent.。

道康宁SYLGARD160灌封胶道康宁SYLGARD170灌封胶

道康宁SYLGARD 160灌封胶道康宁SYLGARD 170灌封胶恩讯浦科技有限公司代理销售道康宁（Dow Corning）全系列产品美国道康宁SYLGARD 160A B双组分灌封胶产品介绍：美国道康宁要用法• 浇灌和密封类型• 双组分硅酮弹性体概述SYLGARD 160硅酮弹性体制供货时是一种双组分的套装材料，它由A、B两部分液体组分组成。

A组是灰色的，B组分是微黄色的，以便于识别和检查它们是否彻底混合。

当两组分以1：1重量比或体积比充分混合时，混合液体会固化为柔性弹性体，本产品适用于电气/电子产品的灌封和密封。

SYLGARD 160 硅酮弹性体可在室温下固化，也可在高温下加速固化。

适用期限和室温下固化时间与采用的材料数量无关。

固化时材料无时显的收缩和温升SYLGARD 160 硅酮弹性体完成UL“塑料材料的可燃性试验”，通过UL 94 V-0级认证。

：美国道康宁SYLGARD 170 A B恩讯浦科技有限公司代理销售道康宁（Dow Corning）全系列产品产品介绍：美国道康宁SYLGARD 170 A 和B 硅酮弹性体供货时是一种双组分的套装材料，它由 A 、B 两部分液体组分组成。

A 组分是黑色的，B 组分是微黄色或米黄色的，以便于识别和检查它们是否完全混合。

当两组分以1 : 1 的重量比或体积比充分混合时，混合液体会固化为软性弹性体，本产品理想地适用于电气/电子产品的灌封和密封。

本产品可在室温下完全固化，也可在高温下加速固化以满足快速生产的要求。

SYLGARD 170 A 和B 硅酮弹性体的特性和优点如表 1 所示。

用途由于SYLGARD 170 A 和B 硅酮弹性体具有许多特点，而且成本较低、使用方便，因而是各种电气/电子灌封或密封应用的理想选择。

A、B 两组分以1 : 1 的比例混合，这种混合系统较为精确，而对按重量或体积配比时较小的误差并不很敏感。

同时，这种系统能理想地适用于自动混合与配制设备和大量生产应用。

道康宁产品应用技术手册

第一章产品
第一章产品
道康宁具有配套齐全的高性能硅酮结构密封胶，这些密封胶可以根据其各自具有的独特性能被用于不同的应用中。具体的产品数据信息例如物理性能、应用和限制等都能在产品数据表中找到或登录公司网站查询。
结构性装配硅酮密封胶
道康宁 993N结构性装配硅酮密封胶
道康宁产品应用技术手册
目录
道康宁产品应用技术手册
第一章产品 ................................................................................................................................. 1 结构性装配硅硐密封胶 ......................................................................................................................................................................................................................... 2 中空玻璃专用硅酮密封胶 ................................................................................................................. 3 底涂液 ................................................................................................................................................. 4 表面处理指南 ..................................................................................................................................... 5

品牌全自动生化分析仪

报告书打印分析结果(监视模式，报告模式多种)、工作表、再检清单、校准报告、光度计确认清单、QC清单、报警追踪、反应过程打印、检验量打印、运转信息管理打印
支援功能再现性计算、睡眠模式、急诊简便分析功能、运转信息管理、按样品种类设置、每个项目主机传送功能、操作员ID管理功能在线帮助功能、远程维护功能（任选）
Page 9
HITACHI 7080全自动生化分析仪功能参数
数据处理功能项目选择、自动校准、多点校准、折线校准、校准点选择功能、比色分析运算、速率分析运算、同工酶分析、血清信息、样品空白补偿、项目间运算、实时QC、X-R管理、自动再检功能、校准追踪、测试计算、数据储存（普通样品、急诊样品合计10,000个）
Page 17
HITACHI 7600系列全自动生化分析仪功能参数
7600系列不是单台仪器，而是由三个基本功能模块组成： D模块（2400测试/小时） P模块（800测试/小时） ISE模块（900测试/小时）
因为7600系列的这种模块组合式的设计，所以医院在选择仪器时就可以根据各自不同的实际情况（工作量，开展项目，实验室空间等）任意选择不同功能的模块组成一台生化仪。这种选择可以在仪器使用后随着医院业务量的不断增长随时添加模块来实现测试速度的提升，而无需整套仪器购买。从而减少了未来因速度升级所需支付的成本。
试剂冷藏库
第一试剂盘45个试剂位，第二试剂盘44个试剂位，全部试剂冷藏
反应容器
UV无吸收塑料（光径长度5mm）
反应时间
3，4，5，10，15，22分钟（可根据不同项目设定。但设定为15，22分钟时，处理能力将降低）
反应温度
37.0℃±0.1℃（反应槽：恒温水循环方式）
外形尺寸•质量分析单元：1,448（宽）×800（纵深）×1,230（高）mm•约400kg

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

Product Information
Release Coatings
Syl-Off ®7020Coating DESCRIPTION Syl-Off ®7020 Coating is a 100percent solids, low-viscosity, end-blocked silicone release coating that contains Dow Corning’s low-temperature inhibitor. The coating cures by an addition reaction in the presence of heat. Syl-Off ®7020
Coating is not precatalyzed. It is designed to be used with
Syl-Off ®4000 Catalyst (platinum) and Syl-Off ®7048 Crosslinker and/or Syl-Off ®7678 Crosslinker.HANDLING PRECAUTIONS
PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND MATERIAL SAFETY DATA SHEETS AND CONTAINER
LABELS FOR SAFE USE,PHYSICAL AND HEALTH HAZARD INFORMATION. THE Base polymer component for Syl-Off ®brand solventless,platinum-catalyzed silicone release coatings APPLICATIONS •For use on paper, film and foil •Release liners for pressure sensitive adhesive laminates and tapes •Industrial release papers and films •Casting papers •Nonstick packaging •In-line, double-sided and differential release applications TYPICAL PROPERTIES Specification Writers: These values are not intended for use in preparing specifications.Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.Appearance Colorless Percent Solids 100Specific Gravity at 25°C (77°F)0.99Viscosity at 25°C (77°F), cs 400
Flash Point, closed cup, °C (°F)100 (212)FEATURES
•Solvent-free
•Fast, low-temperature cure
•More compatible with solvent-
based acrylic adhesives than with solvent-based rubber
BENEFITS
•Premium (easy) release at low peel
speeds
•Higher (tighter) release at high peel
speeds
•Long bath life
COMPOSITION
•Liquid
•Vinyl-functional, reactive siloxane
polymer MATERIAL SAFETY DATA SHEET IS A V AILABLE FROM YOUR DOW CORNING REPRESEN-TATIVE, OR DISTRIBUTOR, OR BY WRITING TO DOW CORNING CUSTOMER SERVICE, OR BY CALLING (517) ABLE LIFE AND STORAGE
Syl-Off 7020 Coating has a shelf life of 12 months from date of
manufacture.
P ACKAGING
Available in a variety of container sizes. Contact your local Dow Corning Customer Service Representative for information about container sizes available in your area.LIMITATIONS This product is neither tested nor represented as suitable for medical or
pharmaceutical uses.
05/12/00Syl-Off is a registered trademark of Dow Corning Corporation.Ref. No. 30-051A-01FPH21190©2000 Dow Corning Corporation. All rights reserved.FOOD STATUS
This product complies with the
following FDA regulations governing food-contact applications: 21 CFR 175.300, 21 CFR 176.170 and 21CFR 176.180. It may comply with BGVV or other global regulatory agency or Kosher requirements as well. Contact your local Dow Corning representative for current compliance information.
W ARRANTY
INFORMATION – PLEASE READ CAREFULL Y
The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer’s tests to ensure that Dow Corning’s products are safe, effective, and fully
satisfactory for the intended end use.Dow Corning’s sole warranty is that the product will meet the Dow Corning sales specifications in effect at the time of shipment. Y our exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted. Dow Corning specifically disclaims any other express or implied warranty of fitness for a particular purpose or merchantability. Unless Dow Corning provides you with a specific, duly signed endorsement of fitness for use, Dow Corning disclaims liability for any incidental or consequential damages.Suggestions of use shall not be taken as inducements to infringe any patent.。