LCP物性数据表
1200
OK
弯曲强度
Flexural Strength
D790
Mpa
120
OK
简支梁缺口冲击强度
Impact strength(23℃)
D256
KJ/m2
36
OK
简支梁无缺口冲击强度
Impact strength(23℃)
D256
KJ/m2
55
OK
热变形温度
(1.82Mpa,23℃)
D648
SGS NO:CANEC1403513201 201403/25-2015/03/25
结论
合格
备注:以上数据真实可靠,但并非绝对值,并不作任何商业保证.
东莞市海嵘兴塑胶有限公司
DongGuan HaiRongXinPlastic co.,ltd
产品性能检测报告
编号：YH-QR/CH-25
产品名称
LCP
牌号
6130L
产品颜色
BK
生产批号
检测人
QC-01
检测日期
2014-09-10
测试内容及性能数据
测试项目
Test properties
测试方法
Test method
(ASTM)
标准
单位
Unit
检测结果
判定结果
密度Density
D792
1.62
g/cm3
1.62
OK
拉伸强度
Tensile Strength
D638
90-120
Mpa
110
OK
断裂伸长率
Tensile Elongation
D638
1.5~3
%
2.1
OK
弯曲模量
Flexural Module
D790
1200-1500
℃
270
OK
玻纤含量
Glass Fiber content
灼烧法
%
30
OK
吸水率
Water Absorption
D-570
%
0.2
OK
可燃性
FlammabilityΒιβλιοθήκη UL-94class
V-0
OK
模收缩率
Mould Shrinkage
D955
%
0.03-0.07
OK
注塑温度
310-330，烤料5-6小时
LCP物性范文
LCP物性范文
一、LCP物性简介
LCP（热塑性聚酰胺）是一种用于制造各种结构件的高性能塑料材料。
它有自己的独特特性，具有高耐热，良好的机械性能，抗酸碱性，抗臭氧性，耐水解性，耐温性，抗撞击，抗机械疲劳和抗化学性的优势。
二、LCP物性参数
1.熔点：LCP的熔点一般在240℃到290℃之间，根据具体品种和配
方有所不同，有的可达310℃。
2.收缩率：LCP收缩率小于PC的2-3倍，具有良好的表面质量。
4.弯曲模量：LCP的弯曲模量可达2×105-4.5×105MPa。
5.热凝性：LCP具有良好的热凝性，可以进行塑性成形处理。
6.水解性：LCP的水解性较差，可在热带气候下长期使用。
7.抗氧化性：LCP具有良好的抗氧化性，可以抵御高温环境下氧化破
坏的影响。
8.抗化学性：LCP具有良好的抗化学性，可以抵御极端腐蚀性溶剂和
酸碱性溶剂的腐蚀。
9.失重率：LCP的失重率小，一般为0.2%～0.3%，比PC还要低。
10.导热系数：LCP的导热系数较小，一般为0.24W/mK，比PC高。
11.电介质性：LCP具有良好的电介质性，具有良好的电绝缘性能和
电阻率。
LCP物性
20
20
15
15
10
10
5
5
0 0 0.1 0.2 0.3 0.4 0.5 0.6
0 0 0.1 0.2 0.3 0.4 0.5 0.6
注）図1〜10、表1〜5は、特記がない限りWT（白色）又はNC（自然色）グレードの値を示しています。 他の色については値が多少変化する可能性があります。 これらの値は材料の代表値であるため、製品規格の設定や単独で設計根拠としてご使用される事はおすすめできません。
®
ASTM D4812
図7 ゼナイト®6130の曲げ疲労特性
700 650 600 550 500 450 400 350 300 0.02 0.05 0.1 1 2 5 1壊強度特性
42 40 38 36 34 32 30 28 26 0 50 100 150 200
9000HT
9140HT BK010 9140HT NC010
356* 356*
40%ガラス繊維強化、超高耐熱 40%ガラス繊維強化、超高耐熱
特殊
FG6330 NC011 FG7145L BK011 ZE16401 BK010 ZE55201 BK010 ZE55801 NC010
245 295 245 290* 260
30%ミネラル強化、低そり、米国 FDA 規格適合、食品接触用途向け 45%ガラス繊維強化、潤滑、米国 FDA 規格適合、食品接触用途向け 5%テフロン 30%ミネラル強化、耐摩擦耐磨耗 50%ミネラル・ガラス繊維強化、潤滑、超低そり 30%ガラス繊維強化、潤滑、電解メッキ性改良
*ISO 75-1/-2 1993/N2による。 他の荷重たわみ温度はISO 75-1/-2による。
lcpe130i物性表中文
lcpe130i物性表中文《lcpe130i物性表中文》是一本关于lcpe130i物质的物性表，其中列出了lcpe130i物质的各种物理特性。
lcpe130i是一种特殊的聚烯烃，在临界点以上具有很高的热稳定性和耐热性，可以在高温高压下使用，并且具有良好的高温抗冲性。
lcpe130i物质的粘度低，可以有效地龙格库塔化，能够在具有良好的微观结构的环境下形成聚合物复合物，从而获得良好的机械性能和集成化能力。
lcpe130i物质在实验室及工业生产中广泛应用，如胶粘剂、水性涂料、润滑油、冶金抗氧剂印染树脂、电子工程树脂及工程塑料、缝纫润滑剂等，能够有效满足各种工业或商业应用的需求。
从结构来看，lcpe130i物质的分子量约为1300，其中每个单位具有130个碳原子，由6条环和6条双键组成。
它的熔点低，在-50℃～-60℃范围内可以完全融化，临界点约为130℃，广泛应用于胶粘剂、水性涂料、润滑油等各种材料中。
它具有弹性高、硬度低、抗疲劳性强、耐热性高等特点，且能维持释放温度至-60℃以下，耐油性良好，具有好的分散性，容易与各类颜料和填料混合，且保持均匀。
以下是lcpe130i物性表中文的一些具体内容：分子式、熔点、融化温度、热稳定性、沸点、临界点、抗疲劳强度、抗冲性能等。
分子式：C130H220熔点：-50℃～-60℃融化温度：130℃热稳定性：可在260℃下使用沸点：210℃临界点：130℃抗疲劳强度：抗疲劳强度可达100MPa抗冲性：具有良好的高温抗冲性。
lcpe130i物质的优势在于它的低粘度，可以有效地龙格库塔化，从而形成聚合物复合物和具有良好微观结构的环境，从而获得良好的机械性能和集成化能力，并且具有良好的耐油性，可以长期保持均匀。
此外，与传统的橡胶和塑料相比，lcpe130i物质具有更高的抗疲劳强度，耐油性和耐热性，在实验室及工业生产中广泛应用，可以满足各种工业或商业应用的需求。
总之，lcpe130i物质具有极强的耐热性、高温抗冲性、耐油性和低粘度等独特特性，能够满足各种不同的工业应用需求。
LCP CoolPoly D5506物性表
> 572 °F 505 °F
3.4E-6 in/in/°F 3.1E-6 in/in/°F 0.239 Btu/lb/°F
69 Btu·in/hr/ft²/°F 5.00 cSt 额定值 (英制) 2.0E+14 ohm 1.6E+16 ohm·cm 1200 V/mil
总体
材料状态
• 已商用：当前有效
资料 1
• Processing (English) • Technical Datasheet (English)
UL 黄卡 2
• E229777-101728974
搜索 UL 黄卡
• Cool Polymers, Inc. • CoolPoly®
供货地区
• 北美洲 • 拉丁美洲
电气性能 表面电阻率 体积电阻率 介电强度 介电常数 100 Hz 1 MHz
额定值 (英制) 1.80 g/cm³
1.0E-3 in/in 3.0E-3 in/in 额定值 (英制) 1.58E+6 psi
7250 psi 0.70 % 1.78E+6 psi 12200 psi 额定值 (英制)
1000 J/kg/°C 10 W/m/K
5.00 cSt 额定值 (公制) 2.0E+14 ohm 1.6E+16 ohm·cm
46 kV/mm
4.50 3.50
测试方法 ISO 1183 ASTM D955
测试方法 ISO 527-2 ISO 527-2 ISO 527-2 ISO 178 ISO 178 测试方法 ISO 179 ISO 179 测试方法
杜邦物性表LCP 6130L BK010
Product Informationd Zenite ®LCPliquid crystal polymer resinZenite ® 6130L BK010Lubricated 30% Glass Reinforced Liquid Crystal Polymer ResinMechanicalStress at Break, 1.0mm ISO 527-1/-2MPa (kpsi)-40°C (-40°F)260 (38) -30°C (-20°F)240 (35) 23°C (73°F)180 (26.1) 120°C (250°F)70 (10.2) 150°C (300°F)55 (8) 200°C (390°F)40 (5.8) 250°C (480°F)22 (3.2)Stress at Break, 2.0mm ISO 527-1/-2MPa (kpsi)-40°C (-40°F)225 (33) -30°C (-20°F)210 (30) 23°C (73°F)150 (21.7) 120°C (250°F)60 (8.7) 150°C (300°F)50 (7.3) 200°C (390°F)35 (5.1) 250°C (480°F)20 (2.9)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.Zenite ® is a DuPont registered trademark.020214/020214The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersDuring molding, use protective equipment and clothing. Skin contact with molten Zenite ® resins can cause severe burns. Be particularly alert during purging.Zenite ® 6130L is a lubricated 30% glass reinforced LCP resin. It is well suited for use in the automotive, electrical/electronic, telecommunications, and aerospace industries.PropertyTest MethodUnitsValueZenite® 6130L BK010Property Test Method Units ValueMechanicalStress at Break, 4.0mm ISO 527-1/-2MPa (kpsi)-40°C (-40°F)200 (29)-30°C (-20°F)190 (27.5)23°C (73°F)130 (18.9)120°C (250°F)55 (8)150°C (300°F)45 (6.5)200°C (390°F)30 (4.4)250°C (480°F)18 (2.6)Strain at Break, 1.0mm ISO 527-1/-2%-40°C (-40°F) 1.7-30°C (-20°F) 1.823°C (73°F) 1.9120°C (250°F) 1.2150°C (300°F) 1.2200°C (390°F) 1.1250°C (480°F) 1.0Strain at Break, 2.0mm ISO 527-1/-2%-40°C (-40°F) 1.8-30°C (-20°F) 1.923°C (73°F) 2.2120°C (250°F) 1.5150°C (300°F) 1.3200°C (390°F) 1.1250°C (480°F) 1.1Strain at Break, 4.0mm ISO 527-1/-2%-40°C (-40°F) 1.9-30°C (-20°F) 1.923°C (73°F) 1.8120°C (250°F) 1.7150°C (300°F) 1.4200°C (390°F) 1.1250°C (480°F) 1.0Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueMechanicalTensile Modulus, 1.0mm ISO 527-1/-2MPa (kpsi)-40°C (-40°F)21900 (3180)-30°C (-20°F)20000 (2900)23°C (73°F)16700 (2430)120°C (250°F)7800 (1150)150°C (300°F)6900 (1000)200°C (390°F)5500 (800)250°C (480°F)4500 (650)Tensile Modulus, 2.0mm ISO 527-1/-2MPa (kpsi)-40°C (-40°F)19700 (2850)-30°C (-20°F)18300 (2650)23°C (73°F)15300 (2220)120°C (250°F)7300 (1050)150°C (300°F)6500 (950)200°C (390°F)4700 (680)250°C (480°F)3000 (430)Tensile Modulus, 4.0mm ISO 527-1/-2MPa (kpsi)-40°C (-40°F)19000 (2760)-30°C (-20°F)18000 (2600)23°C (73°F)13000 (1890)120°C (250°F)6400 (930)150°C (300°F)5900 (850)200°C (390°F)4200 (610)250°C (480°F)2700 (390)Flexural Modulus, 1.0mm ISO 178MPa (kpsi)-40°C (-40°F)20800 (3020)23°C (73°F)16200 (2350)120°C (250°F)7820 (1130)150°C (300°F)7500 (1100)200°C (390°F)5830 (850)250°C (480°F)3820 (550)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueMechanicalFlexural Modulus, 2.0mm ISO 178MPa (kpsi)-40°C (-40°F)16600 (2400)23°C (73°F)12500 (1800)120°C (250°F)7600 (1100)150°C (300°F)7100 (1000)200°C (390°F)5070 (740)250°C (480°F)3690 (530)Flexural Modulus, 4.0mm ISO 178MPa (kpsi)-40°C (-40°F)15700 (2300)23°C (73°F)12000 (1740)120°C (250°F)6900 (1000)150°C (300°F)6200 (900)200°C (390°F)5050 (730)250°C (480°F)3560 (520)Flexural Strength, 1.0mm ISO 178MPa (kpsi)-40°C (-40°F)327 (47)23°C (73°F)211 (31)120°C (250°F)79 (12)150°C (300°F)65 (9)200°C (390°F)43 (6)250°C (480°F)23 (3)Flexural Strength, 2.0mm ISO 178MPa (kpsi)-40°C (-40°F)287 (42)23°C (73°F)191 (28)120°C (250°F)75 (11)150°C (300°F)61 (9)200°C (390°F)39 (6)250°C (480°F)21 (3)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueMechanicalFlexural Strength, 4.0mm ISO 178MPa (kpsi)-40°C (-40°F)258 (37)23°C (73°F)167 (24)120°C (250°F)68 (10)150°C (300°F)54 (8)200°C (390°F)37 (5)250°C (480°F)20 (3)Izod Impact ASTM D 256J/m (ft lb/in)3.2mm (0.126in)120 (2.3)Notched Charpy Impact ISO 179/1eA kJ/m2-30°C (-22°F)3023°C (73°F)35Unnotched Charpy Impact ISO 179/1eU kJ/m2-30°C (-22°F)2523°C (73°F)35ThermalDeflection Temperature ISO 75-1/-2 °C (°F)1.80MPa265 (510)Melting Temperature ISO 3146C °C (°F)335 (635) ElectricalSurface Resistivity IEC 60093ohm>1E15Relative Permittivity IEC 602501E2 Hz 4.51E6 Hz 4.0Volume Resistivity IEC 60093ohm m>1E14Dielectric Strength, Short Time, 0.8mm ASTM D 149kV/mm (V/mil)23°C (73°F)40 (1020)120°C (250°F)41 (1050)150°C (300°F)37 (950)200°C (392°F)40 (1010)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueElectricalDielectric Strength, Short Time, 1.6mm ASTM D 149kV/mm (V/mil)23°C (73°F)35 (900)120°C (250°F)33 (840)150°C (300°F)31 (800)200°C (392°F)33 (850)Dielectric Strength, Short Time, 3.2mm ASTM D 149kV/mm (V/mil)23°C (73°F)29 (740)120°C (250°F)28 (730)150°C (300°F)27 (680)Dielectric Strength, Step by Step ASTM D 149kV/mm (V/mil)0.8mm (0.032in)30 (760)1.6mm (0.063in)29 (740)3.2mm (0.126in)26 (650)Dielectric Const, 1E03 Hz, 0.8mm (0.032in)ASTM D 15023°C (73°F) 4.0120°C (250°F) 4.5150°C (300°F) 4.5200°C (392°F) 4.5Dielectric Const, 1E03 Hz, 3.2mm (0.125in)ASTM D 15023°C (73°F) 4.4120°C (250°F) 5.0150°C (300°F) 5.0200°C (392°F) 5.0Dielectric Const, 1E06 Hz, 0.8mm (0.032in)ASTM D 15023°C (73°F) 3.6120°C (250°F) 4.3150°C (300°F) 4.4200°C (392°F) 4.4Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueElectricalDielectric Const, 1E06 Hz, 3.2mm (0.125in)ASTM D 15023°C (73°F) 3.9120°C (250°F) 4.8150°C (300°F) 4.8200°C (392°F) 4.9Dielectric Const, 1E09 Hz, 0.8mm (0.032in)ASTM D 2520 B23°C (73°F) 4.4120°C (250°F) 4.4150°C (300°F) 4.4200°C (392°F) 4.5Dielectric Const, 1E09 Hz, 1.6mm (0.063in)ASTM D 2520 B23°C (73°F) 4.3120°C (250°F) 4.4150°C (300°F) 4.4200°C (392°F) 4.5Dielectric Const, 1E09 Hz, 3.2mm (0.125in)ASTM D 2520 B23°C (73°F) 4.3120°C (250°F) 4.4150°C (300°F) 4.4200°C (392°F) 4.5250°C (482°F) 4.8Dissipation Factor IEC 60250E-41E2 Hz1501E6 Hz310Dissipation Fact, 1E03 Hz, 0.8mm (0.032in)ASTM D 15023°C (73°F)0.013120°C (250°F)0.008150°C (300°F)0.009200°C (392°F)0.015Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueElectricalDissipation Fact, 1E03 Hz, 3.2mm (0.125in)ASTM D 15023°C (73°F)0.013120°C (250°F)0.006150°C (300°F)0.007200°C (392°F)0.014Dissipation Fact, 1E06 Hz, 0.8mm (0.032in)ASTM D 15023°C (73°F)0.026150°C (300°F)0.016200°C (392°F)0.010Dissipation Fact, 1E06 Hz, 3.2mm (0.125in)ASTM D 15023°C (73°F)0.027120°C (250°F)0.032150°C (300°F)0.018200°C (392°F)0.009Dissipation Fact, 1E09 Hz, 0.8mm (0.032in)ASTM D 2520 B23°C (73°F)0.004120°C (250°F)0.012150°C (300°F)0.018200°C (392°F)0.025Dissipation Fact, 1E09 Hz, 1.6mm (0.063in)ASTM D 2520 B23°C (73°F)0.004120°C (250°F)0.014150°C (300°F)0.020200°C (392°F)0.028Dissipation Fact, 1E09 Hz, 3.2mm (0.125in)ASTM D 2520 B23°C (73°F)0.004120°C (250°F)0.016150°C (300°F)0.023200°C (392°F)0.032250°C (482°F)0.034Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymersZenite® 6130L BK010Property Test Method Units ValueElectricalElectric Strength IEC 60243-1kV/mm37CTI ASTM D 3638V100-174 FlammabilityFlammability Classification UL940.38mm V-00.75mm V-01.5mm V-03.0mm V-01.5mm Nominal Rating UL94V-01.5mm Nominal Thickness Tested UL94mm 1.5Other Thickness Rating UL94V-0Other Thickness Tested UL94mm0.38Oxygen Index ISO 4589%41OtherDensity ISO 1183kg/m3 (g/cm3)1620 (1.62) ProcessingMelt Temperature Range °C (°F)350-360 (660-680)Melt Temperature Optimum °C (°F)355 (670)Mold Temperature Range °C (°F)30-160 (85-320)Mold Temperature Optimum °C (°F)90 (194)Drying Time, Dehumidified Dryer h4Drying Temperature °C (°F)130 (265)Processing Moisture Content%<0.01Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.Zenite® is a DuPont registered trademark.020214/020214 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Start with DuPont Engineering Polymers - /enggpolymers。
住友各规格LCP塑胶料中文规格书、物性表
1013 125 155
V-0 ALL 0.3 0.44
3.4 3.1 0.023 0.004 1014 -
E5204L 玻璃纤维
/无机 400 1.21 0.02 0.57 1.7 89 5.5 93
6960
-
-
343
R90 351 1.3 7.3 V-0 NC,BK 0.29 0.38 3.1 2.8 0.018 0.003 1013 -
度
槽(无)
ASTM D256
MPa J/m J/m
剪切强度
ASTM D732 MPa
泊松比
ASTM D785
洛氏强度
ASTM D785 R比例尺
负荷弯曲温度
ASTM D648
℃
耐焊锡性
线膨胀系数
MD
（150℃）
TD
住化法 住化法
℃ ×10-5/℃ ×10-5/℃
界限氧指数
JIS K7201
-
难燃等级
0.018 0.035
1013 130 185
309
305 V-0 BK 0.3 0.41 0.35 2.9 0.013 1013 -
412
51 0.46 R103 279 300 1.3 5.6 48 V-0 ALL 0.3 0.52 0.45 4.4 3.9
0.022 0.022
1013 130 125
255
48 0.45 R107 242 275 0.8 8.4 49 V-0 NC,BK 0.38 0.55 0.47 4.6 3.9
0.026 0.032
1013 125 155
275
49 0.42 R107 242 275 0.8 7.8 49 V-0 NC,BK 0.38 0.56 0.48 4.7 4.1
LCP物性表
LCP物性认证数据表
性能项目
测试条件
测试方法
数值/描述
单位
机械性能
拉伸强度(引张强度)
ASTM D638/ISO 527
145
kg/cm²(MPa)[Lb/in2]
拉伸模量
ASTM D638/ISO 527
kg/cm²(MPa)[Lb/in2]
拉伸屈服伸长率(延伸率)
ASTM D638/ISO 527
体积电阻率
ASTM D257/IEC 60093
Ω.cm
表面电阻率
ASTM D257/IEC 60093
Ω
耐电弧性
ASTM D495/IEC 60112
特性
高耐热,高流动，玻璃纤维,标准
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
物性性能
比重（密度）
ASTM D792/ISO 1183
1.41
吸水率23℃/24H
ASTM D570/ISO 62
%
热性能
热变形温度
退火
ASTM D648/ISO 75
280
℃（℉）
未退火
ASTM D648/ISO 75
℃（℉）
%
拉伸断裂伸长率(延伸率)
ASTM D638/ISO 527
%
弯曲模量(弯曲弹性率)
ASTM D790/ISO 178
14000
kg/cm²(MPa)[Lb/in2]
弯曲强度
ASTM D790/ISO 178
200
kg/cm²(MPa)[Lb/in2]
IZOD缺口冲击强度
1/4" 23℃
住友各规格LCP塑胶料中文规格书、物性表
350
96 240 290 1 6.2 48 V-0 NC,BK 0.3 3.8 3.4 0.033 0.004 1013 132 200
200
102 266 280 48 V-0 NC,BK 0.3 4.1 3.8 0.02 0.004 1013 181 200
88
441
50 0.41 R89 335 340 0.1 6.4 47 V-0 ALL 0.3 0.56 0.48 4.7 4.2
0.015 0.031
1013 128 175
E5002L
玻璃纤维
400 1.45 0.02 0.07 1.27 150 4.7 127
9510
-
175
480
0.51
354 350 0.2 8.1
V-0 ALL 0.3 0.44
3.4 3.1 0.023 0.004 1014 -
E5204L 玻璃纤维
/无机 400 1.21 0.02 0.57 1.7 89 5.5 93
6960
-
-
343
R90 351 1.3 7.3 V-0 NC,BK 0.29 0.38 3.1 2.8 0.018 0.003 1013 -
-
-
118
520
52 0.49 R91 313 330 1.4 6.2 48 V-0 NC,BK 0.3 0.57 0.49 4.5 3.9
0.018 0.034
1013 130 145
461
58 0.48 R91 310 335 0.2 8.1 44 V-0 NC,BK 0.3 0.53 0.46 4.4 3.7
三星精密化学LCP_V5
LCP概述
特性性能
射出成型
主要用途
主要用于制造骨架线圈（Bobbin） 主要填充物为磨制玻纤以及矿物
LCP (SELCION ®)
主要用于制造连接器（Connector） 主要填充物为磨制玻纤、短切玻纤以 及矿物，（亦可根据客户需要）
Optical Pickup级、Relay级LCP也将于不久开始生产。
* 如果加热套的设定温度和树脂实际温度有差别时，成型时需以实际的树脂温度为准.
20
LCP (SELCION ®)
SAMSUNG FINE CHEMICAL
19
ASTM D792 ASTM D638 MPa ASTM D638 % ASTM D790 MPa ASTM D790 GPa ASTM D6110 J/m ASTM D256 J/m ASTM D256 J/m IN HOUSE MPa IN HOUSE MPa IN HOUSE MPa ASTM D648 ℃ IN HOUSE % IN HOUSE % IN HOUSE IN HOUSE ℃ ASTM D150 ASTM D150 ASTM D495 s ASTM D149 KV/mm DIN EN 60112 -
LCP概述
特性性能
射出成型
主要用途
循环使用
将30%的回收三星LCP加入到全新料中，在最初的几次回收中，整体强度指标只 有轻微的变化。即使是100%的回收材料使用到四次之内，热性能基本上没有变 化，强度也可以保持在90%以上。
（a）DTUL
（b）成型收缩率
14
LCP (SELCION ®)
SAMSUNG FINE CHEMICAL
LCP (SELCION ®)
SAMSUNG FINE CHEMICAL
LCP物性_温度大全
型号负荷温度型号负荷温度宝理A标准级B高刚性A130230、240标准的GF增强B130240A140240高刚性GF增强B230240A150240A150B210低冲模压力（高流动）玻璃短纤维C耐热级A150F215低翘曲玻璃片状物增强C130255A230240碳玻璃纤维增强高刚性低比重C140255A410235高物性尺寸稳定玻璃、无机物增强C150255A460160低异性性硅增强C130M215A466180低异性性硅增强C400250A430190滑动性PTFE增强C810210C820200D 密封级EI 高耐热 高流动级D130M210力（高流动）玻璃短纤维E130I275E140I280T超高耐热级（高熔点）E150I275 T130300E130G240 T150295E471I265 T130M270E472I270E473I250S超高耐热级（高温刚性）S135340标准 玻璃纤维增强日本石油化学杜邦G330260GF30＜6130L277/260G430314GF30＜7130L289MG350256GF＋MD50＜尺寸稳定性6330/239MG450305GF＋MD50＜尺寸稳定性 高耐热6244LRC210349GF30＜超高耐热FC110345GF40＜超高耐热东丽FC120308＜尺寸稳定性 高耐热L204G35250G445310GF45＜高耐热 高刚性L204G35J250M450295MD50＜高耐热 低ciliL204G35H250G345262GF45＜高刚性L204G35R250M350245MD50＜低ciliL204M50250L204M35250L204M40245上野住友2030G250GF30＜E5008335GF强化2125G250GF25＜E5008L339GF强化2140GM235GF＋MD40＜ 低ciliE4008313GF强化4040G240GF40＜E6006L284GF强化5030G230GF30＜高强度E4006L310GF强化5050GM230GF＋MD50＜尺寸稳定性E6008279GF强化5540G230GF40＜E6810284GF强化 无机物6030G285GF30＜高热度E6807LHF270GF强化6040G280GF MD 40高耐热低ciliE7006L242GF强化E7008242GF强化标准玻璃纤维增强碳玻璃纤维增强标准的GF 增强高刚性GF增强高刚性GF增强低冲模压力（高流动）玻璃短纤维高反射率（LED 用）玻璃、无机物增强可电镀级无机物增强可电镀级无机物增强标准 玻璃纤维高刚性玻璃纤维高刚性玻璃纤维低冲模压力（高流动）玻璃短纤维标准 低翘曲性（薄壁连接器用）高刚性低翘曲性（薄壁连接器用高刚性低翘曲性（薄壁连接器用GF30GF30MD30GF20MD20。