建筑工程专业英语
建筑工程专业英语
建筑工程专业词汇延伸率：percentage of elongation位移：displacement应力：stress应变：strain应力集中：concentration of stresses应力松弛：stress relaxation应力图：stress diagram应力应变曲线：stress-strain curve应力状态：state of stress钢丝：steel wire箍筋：hoop reinforcement箍筋间距：stirrup spacing加载：loading抗压强度：compressive strength抗弯强度：bending strength抗扭强度：torsional strength抗拉强度：tensile strength裂缝：crack屈服：yield屈服点：yield point屈服荷载：yield load屈服极限：limit of yielding屈服强度：yield strength屈服强度下限：lower limit of yield荷载：load横截面：cross section承载力：bearing capacity承重结构：bearing structure弹性模量：elastic modulus预应力钢筋混凝土：prestressed reinforced concrete预应力钢筋：prestressed reinforcement预应力损失：loss of prestress预制板：precast slab现浇钢筋混凝土结构：cast-in-place reinforced concrete 双向配筋：two-way reinforcement主梁：main beam次梁：secondary beam弯矩：moment悬臂梁：cantilever beam延性：ductileity受弯构件：member in bending受拉区：tensile region受压区：compressive region塑性：plasticity轴向压力：axial pressure轴向拉力：axial tension吊车梁：crane beam可靠性：reliability粘结力：cohesive force外力：external force弯起钢筋：bent-up bar弯曲破坏：bending failure屋架：roof truss素混凝土：non-reinforced concrete 无梁楼盖：flat slab配筋率：reinforcement ratio配箍率：stirrup ratio泊松比：Poisson’s ratio偏心受拉：eccentric tension偏心受压：eccentric compression 偏心距：eccentric distance疲劳强度：fatigue strength偏心荷载：eccentric load跨度：span跨高比：span-to-depth ratio跨中荷载：midspan load框架结构：frame structure集中荷载：concentrated load分布荷载：distribution load分布钢筋：distribution steel挠度：deflection设计荷载：design load设计强度：design strength构造：construction简支梁：simple beam截面面积：area of section浇注：pouring浇注混凝土：concreting钢筋搭接：bar splicing刚架：rigid frame脆性：brittleness脆性破坏：brittle failure20。
建筑工程专业英语词汇
建筑工程专业英语词汇1. Construction - 建筑2. Architect - 建筑师3. Structural engineer - 结构工程师4. Civil engineer - 土木工程师5. Construction site - 建筑工地6. Blueprint - 蓝图7. Foundation - 地基8. Floor plan - 平面图9. Site plan - 地块平面图10. Construction materials - 建筑材料11. Steel - 钢材12. Concrete - 混凝土13. Brick - 砖块14. Masonry - 砌筑15. Framing - 木结构16. Plumbing - 水暖工程17. Electrical work - 电气工作18. HVAC (Heating, Ventilation, and Air Conditioning) - 供暖、通风和空调19. Insulation - 绝缘材料20. Roofing - 屋顶工程21. Windows and doors - 窗户和门22. Interior design - 室内设计23. Lighting - 照明24. Landscape architecture - 园林建筑学25. Sustainable design - 可持续设计26. Green building - 绿色建筑27. Project management - 项目管理28. Quality control - 质量控制29. Construction cost estimation - 建筑造价估算30. Building codes - 建筑法规31. Construction safety - 建筑安全。
建筑类专业英语 建筑工程
建筑类专业英语建筑工程Building ConstructionBuilding construction refers to the process of constructing buildings or other structures. It involves multiple phases, including planning, design, financing, and actual construction. This field requires a combination of technical knowledge, engineering skills, and creativity.The planning phase involves determining the purpose of the building and identifying its intended use. Factors such as location, budget, and architectural style are considered during this phase. Surveying the site and performing feasibility studies are also essential steps in the planning process.After the planning phase, the design phase begins. Architects and engineers collaborate to create detailed drawings and blueprints, which serve as the basis for construction. Design considerations include structural integrity, aesthetics, functionality, and compliance with building codes and regulations.Once the design phase is completed, financing needs to be secured. This involves estimating the cost of construction, obtaining project bids, and applying for loans or grants. Project managers play a crucial role in coordinating financial aspects and ensuring that funds are allocated properly.The actual construction phase is where the design becomes a reality. Skilled laborers, including carpenters, masons, electricians, and plumbers, work together to build the structure. Construction managers oversee the process, ensuring that the project stays onschedule and within budget. They also deal with issues such as safety compliance and quality control.Throughout the construction process, various materials and techniques are used. Building materials range from traditional options such as bricks, concrete, and steel to newer alternatives like sustainable materials and pre-fabricated components. Construction methods can vary depending on the project requirements and available technology.It is essential to ensure that building codes and regulations are followed during construction. These regulations are in place to ensure the safety and stability of the structure, as well as to address environmental concerns. Building inspectors play a critical role in inspecting and approving construction at various stages.Once construction is complete, the building undergoes a final inspection. If everything meets the required standards, a certificate of occupancy is issued, allowing the building to be occupied and used. Post-construction maintenance and repairs are also necessary to ensure the longevity and safety of the structure.In conclusion, building construction is a complex process that involves numerous stages and requires expertise from various professionals. From planning and design to actual construction and ongoing maintenance, careful attention to detail and adherence to regulations are crucial for successful building projects.。
建筑工程英语怎么说
建筑工程英语怎么说建筑工程在英语中可以被称为"construction engineering"，也可以简称为"building engineering"或者"civil engineering"。
下面我会为您详细介绍关于建筑工程的英语表达。
一、建筑工程概述Building engineering, also known as construction engineering or civil engineering, refers to the discipline of designing, constructing, and maintaining structures such as buildings, bridges, and roads. It combines principles of engineering, architecture, and construction management to ensure the successful completion of construction projects.二、建筑工程项目1. 建筑设计 - Architectural DesignArchitectural design is the process of creating a conceptual plan for a building or structure. It involves designing the layout, aesthetics, and functional aspects of the project.2. 结构工程 - Structural EngineeringStructural engineering focuses on the design and analysis of the structural components of a building. This includes the foundation, beams, columns, and other load-bearing elements.3. 机电工程 - Mechanical and Electrical EngineeringMechanical and electrical engineering involves the design and implementation of systems such as heating, ventilation, and air conditioning (HVAC), electrical wiring, and plumbing within a building.4. 施工管理 - Construction ManagementConstruction management involves overseeing the entire construction process, including scheduling, budgeting, and coordinating the activities of various contractors and subcontractors.5. 质量控制 - Quality ControlQuality control is crucial in construction engineering to ensure that the materials and workmanship meet the required standards. This involves inspections, testing, and adherence to regulations and codes.6. 健康安全 - Health and SafetyHealth and safety measures are essential on construction sites to protect workers and minimize risks. This includes implementing safety protocols, providing personal protective equipment (PPE), and conducting regular safety inspections.三、建筑工程流程1. 立项 - Project InitiationProject initiation involves defining the project goals, objectives, and requirements. This includes conducting feasibility studies, obtaining necessary permits, and securing funding.2. 设计 - DesignThe design phase includes creating architectural and engineering drawings, determining the materials and systems to be used, and obtaining necessary approvals from regulatory authorities.3. 招标 - BiddingBidding involves soliciting proposals from contractors and subcontractors to determine the most suitable and cost-effective option for the construction project.4. 施工 - ConstructionDuring the construction phase, the project plans are put into action. This includes site preparation, building the foundation, erecting the structure, installing systems, and completing finishing touches.5. 验收 - Inspection and AcceptanceAfter construction, the project undergoes inspections to ensure compliance with building codes and regulations. Once approved, the owner accepts the completed project.6. 运维与维护 - Operation and MaintenanceAfter completion, buildings and structures require regular operation and maintenance to ensure their functionality and longevity. This includes routine inspections, repairs, and upgrades.四、建筑工程词汇1. 建筑师 - Architect2. 工程师 - Engineer3. 建筑材料 - Building Materials4. 蓝图 - Blueprint5. 梁 - Beam6. 柱子 - Column7. 地基 - Foundation8. 电气系统 - Electrical System9. 消防系统 - Fire Protection System10. 空调系统 - HVAC System11. 管道系统 - Plumbing System12. 建筑承包商 - General Contractor13. 土木工程师 - Civil Engineer14. 建筑工人 - Construction Worker总结以上是关于建筑工程英语的一些基本概念、项目、流程以及相关词汇的介绍。
建筑工程专业 英语
建筑工程专业英语词汇（1）建筑工程专业英语词汇（2）建设,建筑,修建 to build, to construct 充水试验 filling water test 建筑学 architecture 错边量 unfitness of butt joint 修筑,建筑物 building 底圈 foundation ring 房子 house 真空度检漏vacuum degree leak test 摩天大楼 skyscraper 公寓楼 block of flats (美作:apartment 丁字焊缝 tee welding block) 渗透探伤 oil whiting test 纪念碑 monument 充水试验 filling water test 宫殿 palace 内侧角焊缝接头 interior angle welding line 庙宇 temple joint 皇宫,教堂basilica 基础沉降 foundation settlement 大教堂 cathedral 测量基准点 datum mark 教堂 church 稳定性试验 stability test 塔,塔楼tower 排气阀 outlet valve 十层办公大楼 ten-storey office block 角钢angle steel 柱 column 构件 component part 柱列 colonnade 机械损伤 mechanical damage 拱 arch 缩孔 shrinkage cavity 市政 town planning (美作:city planning) 折迭 enfoldment 营建许可证,建筑开工许可证 building 碳钢管 carbon steel tube permission 公称直径 nominal diameter 绿地 greenbelt 预埋件 embedded part 建筑物的三面图elevation 轴测图axonometric drawing 设计图plan 布置图arrangement diagram 比例尺scale 氧乙炔气割oxyacetylene gas cutting 预制 to prefabricate 低合金钢管 low alloy steel 挖土,掘土excavation 热影响区 heat affected area 基 foundations, base, subgrade修磨 polish 打地基 to lay the foundations 砂轮片 grinding wheel 砌好的砖列course of bricks 等离子plasma panel 脚手架scaffold,scaffolding 质量合格证书 certification of fitness 重皮 coldlap 原材料raw material 凹凸unevenness 底板bottom plate 缩口necking down 垫层 cushion 端面 head face 侧壁 sidewall 倾斜偏差 dip deviation 中心线 center line 外径 external diameter 条形基础 strip footing 砂轮 grinding wheel 附件 accessories 管件 pipe casting 型钢profile steel 单线图single line drawing 钢板steel plate 平齐parallel and level 熔渣 slag 两端 two terminals 飞溅 welding spatter满扣 buckle 定位焊 tacking 螺栓紧固 bolton 引弧 generating of arc 1周边 periphery 熄弧 quenching of arc 焊道 welding bead 附加应力 additional stress 坡口 beveled edges 同轴度 axiality 外观检查 visual inspection 平行度 parallelism 重皮 double-skin 随机stochastic 水平方向弧度radian in horizontal 允许偏差allowable variation direction 重直度verticality 成型 molding 水平度 levelness 直线度 straightness accuracy 隔离盲板 blind plate 焊缝角变形welding line angular 氩弧焊argon arc welding distortion 压盖螺栓 gland bolt 水平度 levelness 间距spacing 铅垂度 verticality 有效期 period of validity 翘曲变形 buckling deformation 担任 take charge of undertake 角尺angle square 焊条 welding rod 对接焊缝 butt weld 碳钢焊条carbon steel 母材 parent metal 焊丝 welding wire 法兰密封面 flange sealing surface 熔化焊 melting 夹层 interlayer 钢丝steel wire 表面锈蚀浓度surface corrosion 气体保护焊gas shielded arc welding concentration 烘干drying 挠曲变bending deformation 清洗ablution 超声波探伤ultrasonic testing/ ultrasonic 制度s ystem examination 焊接工艺welding procedure 压力容器 pressure vessel 相应 corresponding 预制下料prefabrication baiting 手工电弧焊manual electric arc welding 排版直径 set-type diameter 焊缝 welding line 手工钨极manual tungsten electrode 中幅板center plate 打底render 测量方法 measuring method 电源 power source 基准点 datum mark 交流 alternating current 跳焊 skip welding焊件 weldment 允许偏差 allowable variation 管壁厚度 pipe thickness 补强板 stiffening plate 对接焊缝 butt weld 开孔tapping 工件壁厚workpiece 对接接头banjo fixing butt jointing 飞溅物 splash 角钢 angle iron 沾污 smirch 安装基准圆 installation fundamental 油污 oil stain circle 细锉 smooth file 吊装立柱 hoisting upright column 铣刀 milling cutter 焊接钢管welded steel pipe 氧化膜oxide film 向心斜拉筋centripetal canting pull rope 脱脂处理 ungrease treatment] 带板 band plate 棉质纤维 cotton fibre 槽钢胀圈 channel steel expansion ring 丙酮 acetone 环口 collar extension 硫 sulfur 局部变形 local distortion 2焊剂 welding flux 环缝 circumferential weld 顶板 top plate钢板steel plate 拱顶vault 纵向焊缝longitudinal weld longitudinal seam 顶板加强肋stiffening rib 筒节shell ring 对接 butt joint 封头 end socket 胎具 clamping fixture 卷管reelpipe 卷板机plate bending rolls 强度试验strength test 中心支架center bearing bracket 起弧arc starting 椭圆度ovality 穿堂风 draught 等分线 bisectrix 熔合 fusion 搭接宽度 lap width 反面 reverse side 点焊 spot welding 整体 integral 搭接焊 overlap welding 封堵 block up 对称 symmetrically 焊口 weld bond 螺旋爬梯 cockle stairs 医用胶布 medical proof fabric 放料阀 baiting valve 高频 high frequency 液位计content gauge 焊炬 welding torch 芬兰维萨拉 Vailsla OY 美国美科"Met-coil, USA" 建筑工程专业英语词汇翻译(4) 集中式空调系统 centralized air conditioning system 综合分析判断 comprehensive analysis and 裙房 annex judgement 热源heat source 变压器transformer 平面位置的空间space of planimetric 抽芯loose core position 过道aisle 密封性能sealing performance 三相电容three phase capacitance 机房machine room 节点 timing 芯棒 core rod 专业 "profession or discipline 都可以,要都市规划与土地开发Urban g and Land 根据上下文" Development 连体法兰 coupling flange 社区开发及工业区开发垂直井笼vertical well cage Community Development and Industry Park 变风量variable air rateDevelopment 施工面展开 construction unfolds 开发许可申请Development Permit 违约行为 noncompliance 土地使用变更计划 Land Use Rezoning Plan 合同交底- contract presentation 主要计划及细部计划Master Plan and Detail 管理承包商Management Contractor Plan party 都市计划更新计划 Urban Renewal Plan 工程量work amount 都市设施Urban Design 实施的形象进度progress of 建筑设施Architecture Design implementation 大地工程 Geotechnical Engineering 完工资料as-built documentation 工址调查 Site Investigation 文整 clear-up 现地试验与室内试验In-Situ and Laboratory 审核review Test 汽车式起重机Autocrane 基础工程Foundation Design 深化图纸 deepen drawing 3深开挖工程及建物保护Deep Excavation and 设备配置计划equipment furnishment plan Building Protection 结构预埋配合阶段Structure 新生地及软弱地层改良Reclamation and Soft pre-embedment assistance Ground Improvement stage 山坡地开发与水土保持Slope land 精装修阶段Fine fitment stage Development, Soil and Water Conservation 工程施工阶段Construction stage 潜盾隧道与岩石隧道Shield Tunnel and Rock 工程竣工阶段 Completion stage Tunnel 台钻 Bench drill 大地工程施工顾问Geotechnical Construction 冲击钻Churn drill Consultant 手电钻 Electric portable drill 土壤材料试验 Soil andMaterial 砂轮切割机Abrasive cutting off machine 结构工程Structural Engineering 角钢卷圆机 Angle iron rolling machine 各类钢筋混凝土、预力混凝土、钢结构及钢管道切断器Pipe cutting machine 骨钢筋混凝土结构 Structures of R.C., 铜管调直机 Copper pipe straightening Prestressed Concrete, Steel, and SRC machine 桥梁、高层建筑、地下结构物、隧道、深开管道压槽机Book joint setting machine 挖挡土结构Bridges, High-Rise Buildings, for pipes Underground Structures, Tunnels, Retaining 管道压槽机Book joint setting machine Structures for Deep Excavations for pipes 桥梁安全检测、评估及维修补强Bridge 角向磨光机 Angle polishing machine Inspection, Assessment, and Rehabilitation 电动套丝机 Electric threading machine 钢结构细部设计及制造图Steel Structural 电动卷扬机Electric winch Detail Design and Shop Drawings 电动试压泵Motor-driven pressure test 厂房工程 Industrial Plant pump 工业厂房-石化工厂、钢厂、电厂、气体厂、手动试压泵 Manual pressure test pump科技工业厂房、一般性厂房Industrial 阀门试压机Valve pressure test device 阀门试压机Valve pressure test device Plants--Petroleum and Chemical, Steel, Power, TDC(F)风管加工流水线TDC(F)air Gas, High-Technical and General Plants ductwork fabrication 环保设施工厂-垃圾焚化厂、垃圾掩埋场、污stream line 水处理厂及相关管线Environment Protecting等离子切割机 Plasma cutting machine Plants--Incineration Plants, Garbage Disposal TDC(F)法兰条成型机 TDC(F) flange Plants, Waste Water Treatment Plants and strip shaping mill Piping System 勾码成型机 Forming machine for flange 设备支撑结构、管架、操作平台 Equipment clamp Supporting Structures, Pipe Racks, Operating TDC(F)风管加工成型机 TDC(F) duct Platforms fabrication shaping mill 设备基础 Equipment Foundations 多普勒超声波流量检测仪Doppler 厂区一般土木及公共设施General Civil ultrasonic flow detector Works and Utilities of Plants 温、湿度传感器"Temperature, humidity 运输工程Transportation Engineering senor" 运输规划 Transportation Planning 精密声级计Precision sound level meter 停车场设施工程规划、设计Engineering 风管漏风量测试仪、风室式漏风测试装 Planning& Design for Parking Facilities 置 "Duct air leakage 建筑交通维持计划 Traffic Control & tester, airchamber air leakage testing 4Management during Construction device" 风罩式风量测试仪 Air hood air rate 水利及港湾工程 Hydraulic and Harbor tester Engineering 微压计、毕托管、热球（电）风速仪营建管理Construction Management "Micromanometer , 估价及工程预算制作 Estimates and pitot tube, hot bulb(electrical) Engineering Budget Works anemoscope" 营建管理 Construction Management 潜水泵 Submerged pump 工程监造 Construction Supervision 电动弯管机 Electric pipe bender 施工计划 Construction Plan 铜管弯管机 Copper pipe bender 工程进度控管 Schedule Control during 液压弯管机Hydraulic pipe bender Construction 电动剪刀Electric clipper 施工规划 Construction Specifications 液压铆钉钳Hydraulic riveting clamp 环境工程Environmental Engineering 线槽电锯 Trunking electric saw 环境影响评估 Environment Impact 开孔器Tapper Assessment 电动空压机Electric air compressor 环境监测 Environmental Monitoring 液压千斤顶Hydraulic jack 地下水监测系统 Groundwater Monitoring 液压手推车Hydraulic trolley 污水处理厂Wastewater Treatment Plant 焊条烘干箱Welding rod drying box 污水下水道Sewage System 手拉葫芦Chain block 噪音振动防治Noise and Vibration 道（垫）木 Sleeper 垃圾焚化厂兴建工程 Waste Incinerator 转速表 Tachometer 废弃物处理系统工程 Waste Treatment & 电流钳型表 Clip-style ammeter Disposal 压力表 Pressure gauge 共同管道 Common Ducts 接地电阻测试仪 Earthing resistance 管道及附属设施之规划设计 Planning and testing device Design of Common Ducts Structures and 氧气表 Oxygen gauge 乙炔表Acetylene gauge Subsidiary Facilities 对讲机 Walkie talkie 经济效益分析 Economic and Efficiency 文件和资料 documents and information? Analysis 建设单位 Construction unit 财务评估Financial Evaluation 安装单位 Installation unitz 管理维护办法及组织订定Regulation for the 建筑工程专业英语词汇翻译(3) Management, Maintenance and Organization 送气air supply 电流衰减装置current attenuation 电力复合脂electric force compounded grease 气体延时保护装置time delay 电缆敷设cable laying 熄弧 quenching of arc 电缆槽架 cable channel 成型molding 主干线 trunk line 钢印代号 steel seal 弯头 angle fitting质量分析 quality analysis 剥落处 exfoliation 负责人 principal 银粉 aluminum powder 审批 examine and approve 支持点 supportpoint 补焊工艺 repair welding 拆装 disassembly and assembly 压缩机 compression pump 畅通 smooth 平焊法兰 welded flange 电压等级electric pressure 测试流程图test flow chart 通断实验onoff 5加固措施 reinforcement measure 终端头 terminals 校验 verify余度 remaining 升压 boost pressure 标记牌 notice plate 读数 offscale reading 表册 statistical forms 满刻度值 full-scale value 电缆桥架 cable testing bridge 盲板 blind plate 电机 electric machine压力表 pressure meter 相对湿度 relative humidity 强度 intensity杂物sundries 目测eye survey, visiual inspection 耐压试验withstand voltage test 半径radius 照明器具ligthing paraphernalia 公式 formula 铭牌 nameplate 管路 pipeline 验收规范acceptance specification 严密性leakproofness 接线wiresplice 导电膏 conductive paste 试运 test run 压接 compressionjoint 进线口 incoming line 地上连接 overground 带电 electrified 埋深 buried depth 盘车转子 jigger rotor 接地线 earth wire 二次回路 secondary circuit 说明 description 中心线 center line 分线盒junction box 触头contactor 接地装置earthing deivce 配电power distribution 交叉across 成套whole set 塑料保护管protection tube 楼板 floor slab 塑料带 plastic tape 备件 duplicate part, spare part 防腐处理 preservative treatment 包装 packing 接地极earthing pole 器材equipment 接地电阻测试earth resistance 导线 conducting wire 防雷接地 lightning protection 脱落 fall off 遵守 comply with 规范 specification 避雷网 lightning conduction 电器electrical appliance 引下线down lead 断路器line breaker 搭接焊overlap welding 机械联锁mechanical interlocking 避雷针 lightning rod 碰撞 collision 轻便 portable 镀锌制品zinc coating 断接卡breaking of contact 电阻resistance 配电装置 power distribution equipment 集中接地装置 centralized 串联 cascade connection 干线联接 main line 并列 paratactic 单独 solely 机组 machine set 6。
建筑工程英语词汇
建筑工程英语词汇建筑工程是一门需要掌握丰富的专业术语和词汇的学科。
无论是从事建筑设计、规划、施工管理还是建筑材料供应等方面，熟悉建筑工程英语词汇都是必不可少的。
本文将介绍一些常用的建筑工程英语词汇，希望对读者有所帮助。
1. Architecture（建筑学）- The art and science of designing buildings and other physical structures.2. Structural Engineering（结构工程）- The branch of civil engineering that deals with the design and analysis of structures that support or resist loads.3. Civil Engineering（土木工程）- The branch of engineering that deals with the design, construction, and maintenance of the built environment, including roads, bridges, and buildings.4. Construction（建设）- The process of building or erecting infrastructure or a structure.5. Blueprint（蓝图）- A detailed plan or drawing that outlines the specifications, materials, and dimensions of a structure before it is built.6. Foundation（基础）- The lowest load-bearing part of a building, typically below ground level, which supports the weight of the structure and distributes it to the ground.7. Framing（结构框架）- The skeletal framework of a building that provides support and shape, usually made of wood or steel.8. Concrete（混凝土）- A mixture of cement, sand, gravel, and water that hardens into a strong, durable material used in construction.9. Steel（钢材）- A strong, alloyed metal that is commonly used in construction for its high tensile strength and durability.10. Reinforcement（钢筋）- Steel bars or mesh that are embedded in concrete to increase its strength and resist cracking or bending.11. Plumbing（给水排水系统）- The system of pipes, fixtures, and devices that supply water and remove liquid waste from a building.12. Electrical（电气）- Relating to the design, installation, and maintenance of electrical systems in buildings, including wiring, fixtures, and switches.13. HVAC（供暖通风空调）- Heating, ventilation, and air conditioning systems that control the temperature, humidity, and air quality in a building.14. Insulation（隔热材料）- Material used to reduce heat loss or gain ina building, such as fiberglass, foam, or cellulose.15. Roofing（屋顶）- The material and construction of the uppermost part of a building that protects it from weather elements.16. Waterproofing（防水）- The process of making a building or structure resistant to the ingress of water.17. Renovation（装修）- The process of improving or updating an existing building or structure.18. Demolition（拆除）- The act of tearing down or dismantling a building or structure.19. Survey（测量）- The measurement and mapping of the geographical features of a piece of land or a building.20. Permit（许可证）- An official document granting permission to construct, renovate, or demolish a building.这些建筑工程英语词汇是在实践中经常会遇到的，在建筑设计、施工和管理过程中都是必需的。
《建筑工程专业英语》课程标准
《建筑工程专业英语》课程标准一、课程概述（一）课程定位《建筑工程专业英语》是建筑工程技术专业的一门专业基础课程。
其任务是使学生能够在学习了大学英语及专业课的基础上，初步了解土建类专业英语的写作特点，掌握必备的土建类专业英语词汇及术语，基本上能够借助工具书阅读土建类专业英语文章，在一定程度上掌握土建类专业英语的翻译技巧，为更好地从事本专业的工作打下较扎实的基础。
（二）先修后续课程本课程的先修课程为《大学英语》、《建筑材料》、《建筑力学》等专业基础课，该课程为本课程的学习打下良好的知识基础和理论论证。
本课程的后续课程为建筑工程技术的相关专业。
该课程的学习可为这些课程中涉及的建筑结构、建筑材料的选择等内容的知识学习和技能培养奠定良好的基础。
二、课程设计思路根据本课程的定位和后续课程的学习要求，《建筑工程专业英语》以培养学生的专业英语阅读能力为主要目标，内容涉及：建筑工程概论、建筑制图识图与CAD、建筑材料、建筑构造、建筑工程测量、建筑力学、建筑结构、建筑设备、建筑施工、建筑施工管理、建筑节能。
《建筑工程专业英语》既注重讲解土建类专业英语的知识，又介绍了有关土建类的专业知识。
为了有效的激发学生学习专业英语的自觉性和积极性，教师应灵活的采用启发式、研究式、讨论式等多种研究方法来组织课堂教学，进行听、说、读、写、译的综合训练。
充分发挥学生的积极性，培养他们发现问题、分析问题、解决问题的能力。
三、课程目标本课程应该使学生初步了解土建类专业英语的写作特点，掌握必备的土建类专业英语词汇及术语，基本上能够借助工具书阅读土建类专业英语文章，在一定程度上掌握土建类专业英语的翻译技巧，为更好地从事本专业的工作打下较扎实的基础。
具体目标如下：（一）能力目标1.能借助词典等工具阅读和翻译建筑工程技术专业相关的英文资料。
2．能在涉外交际的日常活动和业务活动中进行专业相关的简单口头和书面交流。
（二）知识目标1.掌握专业相关常用英语术语。
建筑工程学院专业英语
abasement floor 地下室 abrased glass 磨砂玻璃 abrasive floor 防滑地板 absorbing ceiling 隔音天花板顶棚 absorbing glass 隔声玻璃 absorbing hung ceiling 隔声吊顶 abstraction of water 排水 acceptance of constructional work 工程验 收 • accidental load 偶然荷载 • additive 添加剂、外加剂
chief designer 设计总负责人 chilled glass 钢化玻璃 ductile fracture 塑性破坏 crane 起重机、吊车 coarse aggregate 粗骨料 collar tie beam 圈梁 compartment wall 防火墙 隔断墙 concrete form 混凝土模板 concrete slab 混凝土板 mixer 搅拌机 crusher 碎石机
• • • •
artificial cement 人造水泥 aseismatic structure 抗震结构 aseismatic design 抗震设计 plain concrete 普通混凝土 cantilever beam 悬臂梁 capital budget 投资预算 cast in place 现场浇注 cast –in-place concrete 现场浇筑混凝土 cast-in-place pile 现浇桩 cellular concrete 多空混凝土
water-proof membrane 防水层 deflection 挠度 door- knocker 门环 door-saddle 门槛 门踏板 door-rail 门横木 冒头 cassion 沉箱 driven pile 打入桩 earth screw 麻花钻 elastic failure 弹性破坏 joist 格栅 exposed pipe 明管
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
建筑工程专业英语词汇（1）建设建筑,修建to build, to con struct 建筑学architecture 修筑,建筑物buildi ng 房子house 摩天大楼skyscraper 公寓楼block of flats （美作：apartment block）纪念碑monument 宫殿palace 庙宇temple皇宫，教堂basilica 大教堂cathedral 教堂church 塔塔楼tower 十层办公大楼ten-storey office block柱column 柱列colonnade 拱arch 市政town planning （美作:city planning）营建许可证，建筑开工许可证buildi ng permissi on绿地greenbelt 建筑物的三面图elevati on设计图plan 比例尺scale 预制toprefabricate 挖土，掘土excavation 基foundations, base, subgrade 打地基to laythe foundations 砌好的砖歹U course ofbricks 脚手架scaffold, scaffolding 质量合格证书certificatio n of fitn ess原材料raw material 底板bottom plate 垫层cushion 侧壁sidewall 中心线center line 条形基础strip foot ing 附件accessories 型辛钢profile steel 钢板steel plate 熔渣slag 飞溅welding spatter 定位焊tacking 弓丨耳弧generating of arc 建筑工程专业英语词汇（2）充水试验filli ng water test 错边量unfitness of butt joint 底圈foundation ring 真空度检漏vacuum degree leak test 丁字焊缝tee welding 渗透探伤oil whiti ng test 充水试验filli ng water test 内侧角焊缝接头interior angle welding line joi nt 基础沉降foundation settlement 测量基准点datum mark 稳定性试验stability test 排气阀outlet valve 角钢angle steel 构件component part 机械损伤mecha ni cal damage 缩孑L shrinkage cavity 折迭enfoldment 碳钢管carb on steel tube 公称直径nominal diameter 预埋件embedded part 轴测图axonometric drawing 布置图arrangement diagram 氧乙炔气割oxyacetyle ne gas cutt ing 低合金钢管low alloy steel 热影响区heat affected area 修磨polish 砂轮片grinding wheel 等离子plasma panel 重皮coldlap 凹凸unevenness 缩口necking down 端面head face 倾斜偏差dip deviation 夕卜径external diameter 砂轮grinding wheel 管件pipe casting 单线图single line drawing 平齐parallel and level 两端two terminals 满扣buckle 螺栓紧固bolt on熄弧quenching of arc 焊道welding bead 坡口beveled edges 夕卜观检查visual in spect ion 重皮double-skin 水平方向弧度radia n in horiz on tai directio n成型molding直线度straightness accuracy 焊缝角变形welding line angular distortio n水平度levelness 铅垂度verticality 翘曲变形buckli ng deformation 角尺angle square 对接焊缝butt weld 母材pare nt metal 法兰密圭寸面flange seali ng surface夹层in terlayer 表面锈蚀浓度surface corrosion concen trati on挠曲变bending deformation 超声波探伤ultrasonic testing/ ultrasonic exam in ati on压力容器pressure vessel 预制下料prefabricati on bait ing 排版直径set-typediameter 焊缝welding line 中幅板centerplate 测量方法measuri ng method 基准点datum mark 跳焊skip welding 允许偏差allowable variati on 补强板stiffening plate开孑L tapping对接接头banjo fixing butt jointing 角钢angle iron安装基准圆in stallati on fun dame ntal circle吊装立柱hoisti ng upright colu mn 焊接钢管welded steel pipe 向心斜拉筋cen tripetalcanting pull rope带板band plate 槽钢胀圈cha nnel steelexpa nsion ring 环口collar extension 局部变形local distortion 周边periphery 附加应力additio nal stress 同轴度axiality 平行度parallelism 随机stochastic 允许偏差allowable variati on 重直度verticality 水平度levelness 隔离盲板bli nd plate 氩弧焊argon arc welding 压盖螺栓gla nd bolt 间距spaci ng 有效期period of validity 担任take charge of undertake 焊条welding rod 碳钢焊条carbon steel 焊丝welding wire 熔化焊melting 钢丝steel wire 气体保护焊gas shielded arc weldi ng 烘干drying 清洗ablution 制度s ystem 焊接工艺weld ing procedure 相应corresponding 手工电弧焊manual electric arc weldi ng 手工钨极man ual tun gste n electrode 打底render 电源power source 交流alternating current 焊件weldment 管壁厚度pipe thick ness 对接焊缝butt weld 工件壁厚workpiece 飞溅物splash 沾污smirch 油污oil stain 细锉smooth file 铳刀milling cutter 氧化膜oxide film 脱脂处理un grease treatme nt] 棉质纤维cotton fibre 丙酮acet one 硫sulfur环缝circumferential weld顶板top plate 拱顶vault 顶板加强肋stiffening rib 对接butt joint 胎具clamping fixture卷板机plate bending rolls 中心支架cen terbeari ng bracket 椭圆度ovality 等分线bisectrix 搭接宽度lap width 点焊spotwelding 搭接焊overlap welding 对称symmetrically 螺旋爬梯cockle stairs 放料阀baiting valve 液位计content gauge 芬兰维萨拉Vailsla OY 美国美科"Met-coil, USA" 集中式空调系统centralized air con diti oning system裙房annex 热源heat source 平面位置的空间space of planimetric positi on密圭寸性能seali ng performa nee机房machine room 节点timing专业"profession or discipline 都可以，要根据上下文”连体法兰coupli ng flange 垂直井笼verticalwell cage 变风量variable air rate 施工面展开con struct ion un folds 违约行为non complia nee合同交底-contract presentation 管理承包商Manageme nt Con tractor party工程量work amount实施的形象进度progress of impleme ntation完工资料as-built docume ntatio n文整clear-up 审核review 汽车式起重机Autocra ne 深化图纸deepe n draw ing焊齐U welding flux 钢板steel plate 纵向焊缝Iongitudi nal weld Ion gitudi nal seam 筒节shell ring 圭寸头end socket 卷管reelpipe 强度试验stre ngth test 起弧arc starting 穿堂风draught 熔合fusion 反面reverse side 整体integral 圭寸堵block up 焊口weld bond 医用胶布medical proof fabric 高频high frequency 焊炬welding torch建筑工程专业英语词汇翻译（4）综合分析判断comprehensive analysis and judgeme nt变压器transformer 扌由芯loose core 过道aisle三相电容three phase capacitanee 芯棒core rod都市规划与土地开发Urban g and Land Developme nt社区开发及工业区开发Community Development and Industry Park Developme nt开发许可申请Developme nt Permit土地使用变更计划La nd Use Rezo ning Pla n 主要计划及细部计划Master Plan and Detail Pla n都市计划更新计划Urban Ren ewal Pla n都市设施Urban Desig n 建筑设施Architecture Desig n 大地工程Geotech ni cal Engin eeri ng 工址调查Site In vestigati on 现地试验与室内试验In-Situ and Laboratory Test 基础工程Foun dati on Desig n设备配置计戈U equipment furnishment pla n结构预埋配合阶段Structure pre-embedme nt assista neestage精装修阶段Fi ne fitme nt stage 工程施工阶段Con struct ion stage 工程竣工阶段Completio n stage 台钻Bench drill 冲击钻Churn drill手电钻Electric portable drill 砂轮切割机Abrasive cutt ing off mach ine 角钢卷圆机An gle iron rolli ng mach ine 管道切断器Pipe cutt ing mach ine 铜管调直机Copperpipe straighteningmach ine管道压槽机Book joint setting machine for pipes管道压槽机Book joint setting machine for pipes角向磨光机An gle polishi ng mach ine 电动套丝机Electric threadi ng mach ine 电动卷扬机Electric winch电动试压泵Motor-drive n pressure test pump手动试压泵Manual pressure test pump 阀门试压机Valve pressure test device 阀门试压机Valve pressure test device TDC(F)风管加工流水线TDC(F)air ductwork fabricati onstream line等离子切割机Plasma cutt ing mach ine TDC(F)法兰条成型机TDC(F) flange strip shap ing mill勾码成型机Forming machine for flange clampTDC(F)风管加工成型机TDC(F) duct fabrication shaping mill多普勒超声波流量检测仪Doppler ultras onic flow detector温、湿度传感器"Temperature, humidity sen or"精密声级计Precisi on sound level meter 风管漏风量测试仪、风室式漏风测试装置"Duct airleakagetester, airchamber air leakage testing深开挖工程及建物保护Deep Excavation and Building Protection新生地及软弱地层改良Reclamation and Soft Ground Improveme nt山坡地开发与水土保持Slope land Developme nt, Soil and Water Con servati on 潜盾隧道与岩石隧道Shield Tunnel and RockTu nnel大地工程施工顾问Geotech nical Co nstructio n Con sulta nt土壤材料试验Soil and Material结构工程Structural Engin eeri ng 各类钢筋混凝土、预力混凝土、钢结构及钢骨钢筋混凝土结构Structures of R.C.,Prestressed Con crete, Steel, and SRC 桥梁、高层建筑、地下结构物、隧道、深开挖挡土结构Bridges, High-Rise Buildings, Underground Structures, Tunnels, Retaining Structures for Deep Excavatio ns桥梁安全检测、评估及维修补强BridgeIn spect ion, Assessme nt, and Rehabilitati on 钢结构细部设计及制造图Steel Structural Detail Desig n and Shop Draw ings 厂房工程In dustrial Pla nt工业厂房-石化工厂、钢厂、电厂、气体厂、科技工业厂房、一般性厂房In dustrialPlants--Petroleum and Chemical, Steel, Power, Gas, High-Tech nical and Gen eral Pla nts 环保设施工厂-垃圾焚化厂、垃圾掩埋场、污水处理厂及相关管线Environment Protecting Plants--Incineration Plants, Garbage Disposal Plants, Waste Water Treatment Plants and Pipi ng System设备支撑结构、管架、操作平台Equipme nt Supporting Structures, Pipe Racks, Operating Platforms设备基础Equipme nt Foun dati ons 厂区一般土木及公共设施Ge neral Civil Works and Utilities of Pla nts运输工程Tran sportati on Engin eeri ng 运输规戈U Transportation Planning停车场设施工程规划、设计Engineering Planning & Desig n for Parking Facilities建筑交通维持计划Traffic Co ntrol &device"风卓式风量测试仪Air hood air rate tester微压计、毕托管、热球（电）风速仪"Microma no meter ,pitot tube, hot bulb （electrical）an emoscope"潜水泵Submerged pump 电动弯管机Electric pipe ben der 铜管弯管机Copper pipe ben der 液压弯管机Hydraulic pipe ben der 电动剪刀Electric clipper 液压铆钉钳Hydraulic rivet ing clamp 线槽电锯Trunking electric saw 开孑L器Tapper 电动空压机Electric air compressor 液压千斤顶Hydraulic jack 液压手推车Hydraulic trolley 焊条烘干箱Weldi ng rod dryi ng box 手拉胡户Chai n block 道（垫）木Sleeper 转速表Tachometer 电流钳型表Clip-style ammeter 压力表Pressure gauge 接地电阻测试仪Earth ing resista nee testi ng device氧气表Oxygen gauge 乙炔表Acetylene gauge 对讲机Walkie talkie 文件和资料docume nts and in formati on? 建设单位Con struct ion un it 安装单位In stallation unitz 建筑工程专业英语词汇翻译（3）送气air supply 电流衰减装置curre nt atte nu ati on 气体延时保护装置time delay熄弧quenching of arc 成型molding 钢印代号steel seal 质量分析quality an alysis 负责人principal 审批examine and approve 补焊工艺repair weldi ng 压缩机compression pump 平焊法兰welded flan ge 测试流程图test flow chart Man ageme nt duri ng Con struct ion水利及港湾工程Hydraulic and Harbor Engin eeri ng营建管理Con struct ion Man ageme nt估价及工程预算制作Estimates and Engin eeri ng Budget Works营建管理Con struct ion Man ageme nt 工程监造Con struct ion Supervisi on 施工计划Con struction Pla n 工程进度控管Schedule Control during Con struct ion施工规戈U Con struct ion Specificati ons 环境工程En viro nmen tal Engin eeri ng 环境影响评估Environment ImpactAssessme nt环境监测En viro nmen tal Mon itori ng地下水监测系统Grou ndwater Mon itori ng污水处理厂Wastewater Treatme nt Pla nt 污水下水道Sewage System 噪音振动防治Noise and Vibratio n垃圾焚化厂兴建工程Waste Incin erator废弃物处理系统工程Waste Treatment & Disposal共同管道Com mon Ducts管道及附属设施之规划设计Planning and Design of Common Ducts Structures and Subsidiary Facilities经济效益分析Economic and Efficiency An alysis财务评估Fi nan cial Evaluation 管理维护办法及组织订定Regulation for the Man ageme nt. Maintenance and Orga ni zati on电力复合脂electric force compo un ded grease 电缆敷设cable layi ng 电缆槽架cable channel主干线trunk line 弯头angle fitting 录9落处exfoliation 银粉aluminum powder 支持点support point 拆装disassembly and assembly 畅通smooth 电压等级electric pressure 通断实验on off加固措施rei nforceme nt measure 校验verify 升压boost pressure 读数off scale reading 满刻度值full-scale value 盲板blind plate 压力表pressure meter 强度intensity 目测eye survey, visiual inspection 半径radius 公式formula 管路pipeline 严密性leakproofness 导电膏conductive paste 压接compression joint 地上连接overgr ound 埋深buried depth 接地线earth wire 说明description 分线盒junction box 接地装置earth ing deivce 交叉across 塑料保护管protection tube 塑料带plastic tape 防腐处理preservative treatme nt 接地极earthing pole 接地电阻测试earth resista nee 防雷接地light ning protect ion 遵守comply with 避雷网light ning conduction 引下线down lead 搭接焊overlap welding 避雷针lightning rod 镀锌制品zinc coat ing 断接卡break ing of con tact 电阻resista nee 配电装置power distribution equipment 集中接地装置cen tralized串联cascade connection 干线联接main line 并歹U paratactic 单独solely 机组machine set 终端头terminals 余度remaining 标记牌notice plate 表册statistical forms 电缆桥架cable test ing bridge 电机electric machine 相对湿度relative humidity 杂物sun dries 耐压试验withstand voltage test 照明器具ligth ing parapher nalia 铭牌nameplate 验收规范accepta nee specificati on 接线wire splice 试运test run 进线口incoming line 带电electrified 盘车转子jigger rotor 二次回路sec ondary circuit 中心线center line 触头contactor 配电power distribution 成套whole set 楼板floor slab 备件duplicate part, spare part 包装packing 器材equipment 导线con duct ing wire 脱落fall off 规范specification 电器electrical applianee 断路器line breaker 机械联锁mecha ni cal in terlock ing 碰撞collision 轻便portable。