模具常用语中英文对照
模具常用术语中英文对照表
模具常用术语中英文对照表"R，L Co.,Ltd" 模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location耐落胶T eflon Paste偏移量Offset 水塞Water Line Plug 撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position 预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary 丝印Silkprint 不干胶Adhesive Sticker 导向针Guide Din 公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture 探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold 剖面图Cross Section 模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave托司 EJ.GUIDE PIN。
模具常用语中英文对照解析
4.1.2加工说明对照表:夕卜导套OUTER GUIDE BUISHING 起吊杆HANDING PIN实数铣通MILL THRU 正反两面各铣TOP SIDE AND OPP SIDE MILLX:- g0.00 (氮气弹弓过孔，锣穿)单+0.00X:- g 0.00 (DR.THRU FOR GAS SPRING) S+0.00X:- g 0.00 (氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:- g 0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING S+0.00, DP0.00)X:- g 0.00 (氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:- g 0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING S+0.00, DP0.00)X:- g 0.00 (合销孔，铰)X:- g 0.00 (REAM FOR DOWEL)X:- g 0.00 (合销孔，割)单+0.00X:- g 0.00 (W/C FOR DOWEL) S+0.00(正面沉头g 0.00*0.00深，内攻M0.00*1.5牙)(g 0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)(反面沉头g 0.00*0.00深，内攻M0.00*1.5牙)(g 0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:- g 0.00 (合销孔，钻穿)X:- g 0.00 (DR.THRU FOR DOWEL)X:- g 0.00 (一般孔，钻穿)X:- g 0.00 (DR.THRU HL)X:- g 0.00 (穿丝孔，钻穿)X:- g 0.00 (DR.THRU FOR WEDM S.H.)X:- g 0.00 (漏油孔，钻穿)按向视图加工X:- g 0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING X:-(漏油槽，反面CNC单+0.00，锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:- g 0.00 (基准孔，铰)X:- g 0.00 (REAM FOR DATUM HL)X:- g 0.00钻穿(螺丝过孔)内攻M0.00牙X:- g 0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头g 0.00*0.00深)(g 0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头g 0.00*0.00 深)(g 0.00*0.00 C'BORE DP0.00 OPP. SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00）X:-M0.00钻穿,正面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00）X:-M0.00钻穿,正反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00）X:-M0.00盲孔，反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE）X:-M0.00盲孔,正面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 TOP SIDE, THR DP0.00）X:-M0.00盲孔,正反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00）X:-M0.00盲孔,侧面分中攻深0.00组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT）（侧面沉头C0.00*0.00深）（C 0.00*0.00 C'BORE DP0.00 EDGE SIDE）X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00 （拨牙螺丝孔，攻穿）X:-M0.00 TAP.THRU FOR JACK SCREWX:- C 0.00 （塞打过孔，钻穿）X:- C 0.00 DR.THRU FOR SPOOLX:- C 0.00 （弹弓过孔，钻穿）X:- C 0.00 DR.THRU FOR SPRINGX:- C0.00 （弹弓孔，反面沉深0.00）有效深0.00X:- C 0.00 （C'BORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00）X:- C0.00 （弹弓孔，正面沉深0.00）有效深0.00X:- C 0.00 （C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00）X:-（避空孔,锣穿）单+0.00X:- （POCKET THRU）S+0.00X:-（避空孔，正面CNC单+0.00锣深0.00）X:- （POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE）X:-（避空孔，反面CNC单+0.00锣深0.00）X:- （POCKET, CNC MILL S+0.00 DP0.00 OPP SIDE）X:- C 0.00 （避空孔，反面CNC单+0.00，锣深0.00）X:-电 0.00 （POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE）X:- g 0.00 （避空孔，正面CNC单+0.00，锣深0.00）X:- g 0.00 （POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE）X:- g 0.00 （两用销过孔，割）单+0.00X:- g 0.00 （LIFTER PIN, W/C S+0.00）X:-（导尺避空,CNC单+0.00锣穿）X:- （POCKET FOR RAIL, CNC MILL THRU, S+0.00）X:-（导尺避空，正面CNC单+0.00，锣深0.00）X:- （POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00）X:-（导尺避空仮面CNC单+0.00，锣深0.00）X:- （POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00）X:-（浮块避空，正面CNC单+0.00，锣深0.00）X:- （POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00）X:-（浮块孔，割）单+0.00（反面避空单+0.00，锣深0.00）X:- （LIFTER HL, W/C）S+0.00（POCKET DP0.00 S+0.00 OPP.SIDE）X:-（浮块孔，锣）单+0.00（反面避空单+0.00，锣深0.00）X:- （LIFTER HL, MILL）S+0.00（POCKET DP0.00 S+0.00 OPP.SIDE）X:- g 0.00 （顶针孔，钻穿）（反面沉头g 0.00*0.00深，内攻M0.00*1.5牙）X:- g 0.00 （EJECT PIN, DR.THRU.）（g 0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR）X:- g 0.00 （顶针孔，钻穿）（正面沉头g 0.00*0.00深，内攻M0.00*1.5牙）X:- g 0.00 （EJECT PIN, DR.THRU.）（g 0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR）X:- g 0.00 （导柱（导套）孔,CNC锣）单+0.00X:- g 0.00 CNC MILL FOR GUIDE PIN（BUSHING） S+0.00X:- g 0.00 （导柱（导套）孔，割）单+0.00X:- g 0.00 W/C FOR GUIDE PIN（BUSHING） S+0.00X:-M0.00*1.5（止付螺丝，正面攻深0.00）X:-M0.00*1.5（SET SCREW, TAP DP0.00 TOP SIDE）五金模具单词总结模具种类：连续模progressive die 机械手transfer die 手动机械手hand transfer die 单工程模single die/line die 复合模compound die 铆接模riveting die 铸造结构模cast die 能快换的模changeover die 泡沫模pattern互换性：公差toleranee 上公差upper toleranee 下公差lower toleranee 公差范围toleranee range 公差+/- 0.05 plus mi nus 0.05 形位公差图GD&T 平面度flatness 直线度straightness 倾斜度an gularity 垂直度perpendicularity / squareness 平行度parallelism 圆度roundness / circularity 圆柱度cylindricity 面轮廓度surface profile 线轮廓度line profile 位置度true position 同轴度concentricity 对称度symmetry 圆跳动run out 全跳动total run out 尺寸dimension 角度angle degree 全尺寸报告dimensional layout工艺性：料带strip 料带图strip layout 工序process 冲导正孑L pilot pierce 冲孑L pierce 侧冲cam pierce 切边notch成形后的切边trim切侧刃french trim / fringe trim 厚料切边后的精修边shave 折弯be nd 墩薄coin折弯处压筋gusset 成形form 侧成形cam form 整形restrike / rehit 围边flange压线/压长条状筋ribbon 打凸米boss / dimple 打凸包emboss 打字印stamp 打沙拉孑L hourglass 面押coin burr 抽孑L extrude hole 拍平flat / spanking 包边hem edge 压角cone 张角flare 切舌lance 半剪knockout 卷圆curl/热恶劣旋转rotate 铆接rivet 铆螺母stake nut 切断cutoff 接刀口mismatch 料带带料处carrier tabs 毛刺方向burr direct ion 产品切边线trim line模具零件：模具die / tool 上托板upper mounting plate 上垫脚upper parallel 上模座upper die set 上垫板punch backup 上夹板punch holder 止挡板traveling stop 脱料板stripper 下模板die plate 下垫板die backup plate 下模座lower die set 下垫脚lower parallel 上托板base mounting plate 浮块lifter 浮料板lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 刀口直身位land 直5 斜1 5mm Land 1 taper 刀口上沉头的深度die life 沉头counter bore 冲头倒斜shear 高低冲stagger punch 球锁冲头ball-lock punch 球锁座ball-lock retainer 冲孔入子button 顶针kick off / ejector 废料切断刀slug breaker 成型凹模form die 整形公restrike form punch 导尺rail /stock guidanee 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert 侧冲组件cam 滑块slide滑块上油槽oil groove 铲机driver 码模槽mounting slot 储运块storage block 限位柱stop block 起吊孑L handing hole 起吊环eyebolt 模柄shank 靠块heel 摆块rocker bender 脱料板拉杆stripper bolt 模座导正块thrust 耐磨片wear sheet 耐磨板wear plate 垫片shim 两用销lifter pin 初始管位first start pin 内限位standoff 压块keeper 导柱导套压块keeper/ boss 键槽key slot 键key氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mou nting flange 氮气弹簧系统n itroge n man ifold 螺旋弹簧coil spring 聚氨酯弹簧urethane 弹簧套spring cage 导柱guide post 导套guide bushing 插针pilot pin 插针套pilot bushing 插针通孔pilot through hole 侧刃french误检装置misfeeder 传感器sensor 误检杆trigger 油嘴oil nipple 销针dowel pin 螺丝screw 牙thread 拔牙jackscrew 内六角螺钉socket head screw 垫圈washer 螺塞screw plug 盲销blind dowel 行程，走位stroke / travel 吨位tonnage 机械冲床mechanical press 油压机hydraulic press 冲床下台面bolster 冲床上台面ram 冲床台面布置图press layout 冲床码模槽press mounting slot 冲床气垫air cushion 码模钳stirrup 闭合高度shut height 送料高度feeding height 送料机feeder T 型槽T-slot 避位clearanee /pocket 掏空pocket 挂台head 扣位pocket of head 通气孑L air vent hole 漏油孔drain hole 漏料孔slug hole 基准孑L datum hole 通孑L through hole穿丝孑L first wire holeT 型槽T-slot 拔牙jackscrew 摆块rocker ben der闭合高度shut height 避位cleara nee /pocket侧冲组件cam 侧刃french 插针pilot pin 插针套pilot bushi ng 插针通孔pilot through hole铲机driver 沉头coun ter bore成型凹模form die 成型公form punch 冲床码模槽press moun ti ng slot冲床气垫air cushi on冲床上台面ram冲床台面布置图press layout冲床下台面bolster冲孔入子button冲头倒斜shear初始管位first start pin储运块storage block 穿丝孑L first wire hole 传感器sen sor 弹簧套spri ng cage 氮气弹簧gas spri ng / n itroge n氮气弹簧安装法兰mou nting flange氮气弹簧系统n itroge n man ifold刀口trim steelspri ng刀口上沉头的深度die life 刀口直身位land导尺rail /stock guida nee导尺顶杆lifter bolt导料板rail plate 导套guide bush ing导柱guide post导柱导套压块keeper/ boss 垫片shim 垫圈washer顶针kick off / ejector 吨位tonn age废料切断刀slug breaker浮块lifter脱料板拉杆stripper bolt 误检杆trigger误检装置misfeeder下垫板die backup plate下垫脚lower parallel下模板die plate下模座lower die set限位柱stop block镶件/入子in sert销针dowel pin行程,走位stroke / travel压块keeper压料块pressure pad牙thread油压机hydraulic press油嘴oil n ipple整形公restrike form punch直 5 斜 1 5mm Land 1 tap er 止挡板traveli ng s top机加工：开料cutting material 钻drill (DR) 攻牙tap 铰ream 铣mill 车lathe 电脑锣NC mill 线切割wire cutting (W/C) 磨grind 刨planer 电火花EDM 镭射laser cutting 倒角chamfer 精加工finish XX 真空热处理vacuum heat treatment 镀钛TD coating 退磁demagnetization 烧焊weldG :40-M6BLIND HL,TAP DP18.00 OPP SIDE,THR DP18.00)盲孔，反面攻深** G10:4-M30BLIND HL,TAP DP18.00 EDGE SIDE)盲孔，侧攻深**(%%c34.00*14.00 C'BORE DP14.00 TOP SIDE)正面沉头多少X多少深G2 :24-%%c8.00(REAM FOR DOWEL WORK DP16.00 OPP SIDE,DR%%c6.00 HL)G2 :24-%%c8.00(合销,背铰深16.00有效深，内钻%%C6.00通孔)G4 :3-%%c10.00(基准孔,背铰深20.00)背面锣25.00*25.00 方形沉头，深1.00%%P0.01(REAM FOR DATUM HL DP20.00,MILL25.00*25.00 OPP SIDE DP1.00%%P0.01) M:2-%%c15.00(弹簧孔，锣深33.00) (C'BORE OR SPRINGDP33.00 TOP SIDE,WORK DP33.00)X :3-%%c32.00(导套孔，锣穿，单+0.01)(MILL THRU FOR GUIDE BUSHING S+0.01)G :2-M10盲孔,侧攻深30.00(有效深)(BLIND HL,TAP WORK DP30.00 EDGE SIDE)(沉头5.20%%P0.05深)(SLOT DP5.20%%P0.05 TOP SIDE)L :2-%%c8.000(合销,割)单+0.005 (W/C FOR DOWEL)S+0.005盲孑L ,攻深20.00(有效深) (BLIND HL,TAP DP20.00 TOP SIDE,THR DP20.00)(插针孔,割，单+0.01) (W/C S+0.01 FOR PILOT PIN)(避位孑L ,背锣9.80(有效深) (POCKET,MILL DP9.80 OPP SIDE WORK)(冲头过孔，锣穿)(MILL THRU FOR PUNCH CLEARANCE HL)(导柱孔,锣穿，单+0.005) (MILL FOR GUIDE PIN) S+0.005避位槽，背锣深19.00) (POCKET,MILL DP15.40 OPP SIDE)(背，沉头%%c14.00,掏深留11.00) (%%c14.00 C'BORE UNTIL DP14.00 OPP SIDE)下模刀口，实数割，直5斜1.5 (内钻%%C5.0穿丝孔)W/C S+0.00 TRIM STEEL,5.0LAND 1.5TAPER,(DR THRU%%c3.00 WEDM S.H)(MILL FOR INSERT DP30.0%%P0.01 S+0.01)(入子槽,锣深30.00%%p0.01 单+0.01)(氮气槽,背锣深4.00%%P0.1 单+0.1) (GAS SPRING MILL DP4.00 OPP SIDE)S+0.1按向视图加工ACCORDING VIEW DRAWING TO MACHINING试模材料：热扎板HRS (hot-roll steel) 冷扎板CRS (cold-roll steel) 不锈钢板Stainless steel 镀锌板galvanized steel 镀铝锌板galvalume steel 热扎酸洗板HRPO steel (hot-rolled pickled and oiled steel)工具：卡尺caliper 千分尺micrometer 拨牙器jacker 扳手wrench 丝攻screw tap 起子screwdriver 码模钳stirrupPin Gauge标准针规Plastic Injection Machi ne 注塑机Poi nt to Poi nt CMM 三次元测量仪Precisio n surface grin der 精密手摇磨Press冲床Projector profile 投影机Shear Press 剪板机Slow Wire Cutting 慢走丝Vertical Milli ng Machi ne 卧式强力铣床扳手wrench 拨牙器jacker 卡尺caliper 码模钳stirrup 起子screwdriver 千分尺micrometer 丝攻screw tap CARVE 雕刻pothook 挂钩SPECIAL HL 异形孑L 漏斗filler合叶HINGE优力胶RUBBER球锁垫板LOCK WASHER双线边刀口，不倒角TRIM STEEL NEAR THE DOUBLE LINE NO CHAMFER滑块座:SLIDE SET机械：(engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料13-mode 13 工况3rd gear三档齿轮3-way seat 三向座椅4WD control device四轮驱动控制装置4WD in dicator switch 四轮驱动指示灯开关4WD lamp electrical conn ection四轮驱动指示灯接线4WD switch 四轮驱动开关5th syn chromesh assy.五档同步器总成6PK belt 6PK多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy.空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket空调压缩机安装支架A/C con trol assy.空调控制器A/C housing assy.空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch空调状态选择开关abdome n performa nee criteri on 腹部性能指标Abdomi nal Peak Force 腹部力峰值ABS防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator in terlock ing type 力卩速踏板联锁式acco un ti ng foun dati on 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter连接器additional features 附加装置additional rule 附加法规adjust screw调整螺钉adjuster cable 调整拉线adjuster plug 调整盖adjuster screw assy.调整螺栓总成adjuster washer 调整棘片adjuster, diff. beari ng差速器轴承调整螺母Adjustme nt system 调节装置Administration and Registration Division 管理科Angle of rotation 旋转角angles drift off vertical line指针偏离垂直线的角度An gular diameter of the retro-reflect ing device 回复反射装置的角直径annex附件Announ ceme nt 公告an ti, shutdow n screw防不灭车调整螺钉Antilock Brake System 防抱死制动系统appe ndix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant申请人application 申请application for notification 认可申请书approval 认可arm, valve rocket 摇臂armature转子总成armature shaft 电枢轴Arm-rests 靠手Article 条Article 1 第1 条Asphalt solution 沥青溶剂Attached docume nt 附署文件attached sheet 附表Attached Table 附表attach ing locati on of seat belt an chorage座椅安全带固定装置的固定位置attachme nt附属文件Attendants on board车上值班人员automatic chock cover sett ing 自动阻风门盖调至U automotive electric system 汽车电系automotive engine system 引擎系统automatic tran smissi on自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 畐寸簧Auxiliary Stop Lamp 辅助驻车灯axle case 桥壳axle case assy.桥壳总成axle ratio桥速比axle tube 桥管axle weight 轴重back an gle level靠背角水平仪back an gle quadra nt靠背角量角器back pan 靠板back spri ng回位弹簧back ing plate制动底板Backing sheet 衬背板Back-Up Light 倒车灯cover & plate assy.离合器盖及压盘总成cover assy. , air clea ner空气滤清器盖总成cover, gear 侧盖cover, heater air空气加热罩cover, rear axle case后桥壳盖crane vehicle 起重车cran kcase曲轴箱cran kshaft 曲轴cran kshaft gear 曲轴齿轮cran kshaft & conn ect ing 曲轴连杆机构crankshaft oil gallery 曲轴油道cran kshaft sprocket 轴承链轮critical flow 临界流Cross sen sitivity of a lin ear tran sducer 线性传感器的横向灵敏度Crush dista nee 压碎距离Crush rate压碎速率Crush Stre ngth 压碎强度Cumulative time 累计时间cup皮碗cup, diff. side beari ng差速器轴承外圈cup, pinion front beari ng 主动齿轮前轴承外圈cup, pi nio n rear beari ng 主动齿轮后轴承外圈Cut-off明暗截止线cycle冲程cycli nder head cover 气门室罩Cylinder 气缸cylinder block 汽缸体cylinder body 缸体Cyli nder bore 缸径cyli nder head 汽缸盖cyli nder head cover 气门室罩cylinder number 气缸数cylinder working order(clockwise)气缸工作顺序(顺时针) damper转向减振器dan gerous article 危险物darkroom 暗室Data cha nnel数据通道Data Processi ng 数据处理Date of notification 认可日期Decelerati on of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster除霜器dehydrator储液器和干燥器delay valve 延迟阀Desig n torso an gle 设计躯干角designated 认定desig nated motor vehicle 经型式认定的机动车Desig nati on 名称Desig natio n of bus in ess place 业务场所名称Designation of Confirmor 指定确认者det on ati on 爆震device proper装置本身Device type desig nati on 装置的型式认定dextrorotati on 右旋diameter 口径diaphragm 膜片diaphragm of fuel pump 油泵膜片diaphragm retur n spri ng 膜片回位弹簧diaphragm rod 膜片杆diaphragm spri ng 膜片弹簧Diesel fuel 柴油Diesel oil轻柴油diesel smoke柴油排烟Diesel smoke measuring instrument柴油机排烟测量仪diesel-powered motor vehicle 柴油机动车differe ntial case 差速器壳differe ntial gear 半轴齿轮differe ntial gearbox , front axle 前桥减速器differe ntial gearbox , rear axle 后桥减速器differe ntial side gear-to-case cleara nee半轴齿轮与差速器壳之间的间隙Digital magn etic recorder 数字式磁记录仪Digitilizi ng 数字化Diluted exhaust gas 稀释排气dilution tunnel 取样探管direct injectio n type 直喷型directi on in dicator lamp 转向信号灯directly con trolled wheel 直接控制车轮Director of the Vehicle and Comp onent Approvals Divisi on 车辆和零部件认证科长Director-Ge neral 署长Director-Ge neral of District Tran sport Bureau 地方运输局长Director-Ge neral of Land Tran sport Engin eeri ng Departme nt 陆运管理处长Director-Ge neral of Local Land Tran sport Office 地方陆运署长Director-Ge neral of Motor Vehicle In spection and Registratio n Office 机动车检验注册署长disc brakes 碟式刹车disc brake盘式制动器disk assy. , clutch drived 从动盘总成disk type braker盘式制动器Displacement 排气量Displaceme nt system 位移装置Distillation properties 分馏特性distillati on temperature 馏出温度distribution device 配气机构distributor 分电器distributor assy.分电器总成distributor cap 分电器盖distributor rotor 分电器转子distributor shaft 分电器轴distributor type分电器型号District Tran sport Bureau 地方陆运署docume nts to Be Submitted 需提交的文件dome lamp 顶灯door assy. , front RH.右前门总成door assy. , rear RH.右后门总成door hinge assy.车门铰链总成door hinge plate 车门铰链垫板doors assembly & body accessories前后车门总成及其附件double-lip seal双唇油圭寸double-tire 双胎dowel pin定位销合销dowel pin s-pump ring 定子定位销DRAWING PROCEDURE 绘制规程drier干燥剂drier receiver贮液干燥器drier receiver body 贮液气壳体drive end shield 前驱动端盖drive line system 传动系统drive pi nio n gear depth 驱动齿轮深度drive shaft 驱动轴drive sprocket 驱动链轮driver' s Seat驾驶员座椅driv ing beam 远光光束driving wheel 驱动轮drum brakes 鼓式杀V车drum brake鼓式制动器drum type braker鼓式制动器dry air干空气dry basis 干基dry-bulb 干球dummy假人dump自卸车dust boot防尘罩Dy namic test动态试验ECE Regulation ECE 法规eddy-curre nt type 电涡流式efe heater进气加热器Effective height 有效高度Effective Weighted factor 有效加权系数Effective width 有效宽度Electrical汽车电器Electrical System 电器系electromagnetic compatibility 电磁兼容性EMBOSSMENT 凸字Emerge ncy Brake紧急制动器Emerge ncy Exit 紧急出口Emerge ncy Motor Vehicles 应急用车Emerge ncy Sig nals应急信号用具Emerge ncy Stop In dicati on Devices 紧急停车表示用具emerge ncy valve 应急阀Emissio n Con trol Device排放物控制装置end cleara nee轴向间隙ENFORCEMENT PROCEDURE 实施规程En forceme nt Regulati on 实施规则en gi ne发动机，引擎Engine and Power Train System发动机及动力传动系engine assy.发动机总成engine displacement 发动机排量engine hood发动机罩engine in take ma ni fold 发动机进气歧管en gi ne load发动机负荷engine oil发动机润滑油engine oil capacity 发动机机油容量engine outside diagram 发动机外形图engine revoluti on speed 发动机转速engine type发动机型号Engin eeri ng and Safety Departme nt 技术安全咅E entrance step 入口台阶en try item填写项目entry value 填入值eqalizer平衡架Equivale nt in ertia weight 当量惯性重量escort vehicle 护卫车Europea n Econo mic Commu nity Comma nd 欧洲经济共同体指令Exam in ati on 审查exam in ati on affair 审查事务Fluid con tai ner 液体容器fluid torque converter 液力变扭器fluoresce nt surface 荧光面flying wheel 飞轮fog lamp 雾灯fog lamp relay 雾灯继电器fog lamp switch 雾灯开关Foil Thick ness 箔厚folded seat 折叠椅foldi ng seat折叠式座椅foot an gle quadra nt小腿夹角量角器fork拨叉Formalin福尔马林forward-opening inner door 内门前开型four-stroke cycle 四行程引擎four-wheel drive motor vehicle 四轮驱动的机动车Four-wheeled 四轮Frame车架Frame and Body 车架及车身Friction clutch摩擦离合器from evaporator drier 自蒸发器from heater core 出加热器from receiver drier自贮液干燥器from water jacket in take ma ni fold 自进气歧管水套front axle 前桥front axle assy.前桥总成front axle motor 前桥挂档马达front beari ng 前轴承front beari ng retainer 前轴承盖front beari ng, front output shaft 前输出轴前轴承front beari ng, in put shaft 输入轴前轴承front beari ng, output shaft 输出轴前轴承front brake disc 前制动盘front brake disc assy.前制动盘总成front case前壳体front case of vacuum booster 助力器前壳体front coil spring 前螺旋弹簧front comb ined lamps 前组合灯front disk braker前盘式制动器front edge 前边缘front end of shield发电机前端盖front engine front drive F.F 式车辆front engine rear drive F.R式车辆front fan前风扇Front Fogfront shock absorber 前减震器front stabilizer 前稳定杆front suspe nsion 前悬吊front thrust plate 前配流盘front transfer车辆转移台front tube failure前管路失效状态front wall angle cover 前围角板front washer pump 前洗涤器泵front washer reservoir前风挡洗涤器储液罐front wheel前轮，前壳体front wheel alig nment 前轮定位front wheel brake前轮制动器Front Win dshield 前风窗front wiper motor 前刮水器电动机Fron t-E nd Outli ne Marker Lamps 前端示廓灯Fuel燃料fuel direct燃油走向fuel filter 集滤器fuel filter housing燃油滤清器壳体fuel filter paper燃油滤清器滤纸fuel gauge燃油表fuel gauge calibrati on 燃油表电阻Fuel Injection Device 燃料喷射装置fuel level indicator 机油压力表fuel pump然油泵Fuel Resista nee 耐油性fuel sen sor燃油（箱）传感器fuel sen sor harness燃油传感器线束fuel supply system 供油系Fuel System 燃料系Fuel System of Motor Vehicles Whose Fuel Is High-Pressure Ga d 高压气体作为燃料的机动车燃料系Fuel System of Motor Vehicles Whose Fuel Is Producer Gas以发生炉煤气作为燃料的机动车燃料系Fuel Tank燃料箱fule meteri ng bar 计量杆full circle 大循环Full flow dilution 全流稀释full trailer 全挂车full-hydraulic type 全液力式full-trailer 全挂车fully-loaded 全负荷fuse熔断器fuse panel熔断器板garbage truck 垃圾车gas container气体容器gas sample 样气gas turbi ne燃气轮机gasket节温器密圭寸垫，衬垫gasket cyli nder head cover 气门室罩垫gasket, i ntake man ifold 进气歧管衬垫gasket, liftgate han dle举升门手柄垫片Gasoli ne 汽油gasoli ne fueled motor vehicle 汽油机动车gatheri ng heat cover-TCV system TCV 系统集热罩gear , coun ter shaft fifth 五档中间齿轮gear end cleara nee, plastic gauge齿轮端部间隙，塑料间隙规gear hub 齿毂gear range档位级另廿Gear ratio 速比gear to body cleara nce(radial)齿轮至U壳体间隙(径向) gear, 4WD四轮驱动齿轮gear, annu lus 齿圈gear, low shift 抵挡齿轮gear, rearaxle diff.半轴齿轮gear, sleeve 齿套Gear-cha nge lever 变速杆gears档位Gen eral Comme nts 概述General Construction 通用结构GENERAL PROVISIONS 通用规贝U Gen eral provisi ons —般规定gen erator发电机Glaz ing 车窗glove box lamp 杂物箱灯Goods-Load ing Accommodati on 载货装置gover nor type调节器式Gravimeter 重力计Gross Vehicle Weight 车辆总重grou nd Cleara nee 离地间隙Grou nd-Co ntact Section and Con tact Pressures 地部位及接地压力grouped lamp 组合灯grouped, comb ined or reciprocally in corporated lamps 组合、复合或混合灯光组haloge n headlamp 卤素头灯halogen sealed-beam unit (HSB unit)卤素圭寸闭式(HSB) han dle assy. , door I/S车门内手柄总成han die assy. , door O/S前门外手柄总成han die, liftgate lock举升门锁芯手柄han die, wi ndow regulator 玻璃升降器手柄han dii ng处理办法HANDLING PROCEDURE 管理规程han ger调耳harn ess 线束harn ess, body车身线束harn ess, engine hous ing 发动机仓线束harn ess, lift gate 尾门线束hatch-back 掀背型Hazard Warni ng Lamps危险报警闪光灯head缸盖head form头部模型head performa nee criteri on 头部性能指标Head Restrai nt 头枕head room probe头部空间探测杆Headlamp clea ner前照灯清洗器headlamp dimmer switch 变光开关headlamp switch前照灯开关Headlamps前照灯Headlight tester前照灯试验器Heat Resista nee Test耐热性试验heat-damage 热损害heated hydrogen flame ion izatio n detector 加热式氢火焰离子化检测器heater加热器heater & A/C pan el lamp暖风/空调开关灯heater, i ntake ma nifold进气歧管加热器Heavy oil重柴油here in after referred to as 下文称为Here in after the same 下文同hi-beem in dicator lamp 组合仪表远光指示灯high idle speed 高怠速high pressure gas 高压气体high range 高档High-floor 高地板High-floor that can be ope ned in three ways 三向开启的高地板High-Pressure Gas Tran sport Devices 高压气体运输装置hip an gle quadra nt臀部角度量角器hoist举升hold in winding 保持线圈holddown pin拉紧销钉holddow n spri ng 压紧弹簧hole ladder type 带孔梯式hon eycomb cell axes 蜂窝单元轴hon eycomb ribb on axis 蜂窝条纹轴Horiz on tally-opposed 水平对置horn relay喇叭继电器horn switch喇叭按钮Horns喇叭hose assy. , power steering return动力转向回油管总成hose assy. , power to pump油罐至U泵的油管总成hose, coola nt recover冷去卩液回收管hose, radiator in let散热器进水软管hose, radiator to water pump散热器至水泵软管hose, thermostat to in take mi ni fold 节温器至进气歧管软管hot air热空气hot idle mode热怠速状态hot idle screw热怠速调整螺钉hous ing壳体，外壳hous ing assy.壳总成hous ing clutch 离合器壳hous ing end plug 壳体端盖hous ing, steeri ng gear 转向器壳体H-point pivot H 点支轴H-po int sight butt on H 点标记钮hub & beari ng assy.轮毂与轴承总成hub cap车轮盖hub gear 齿毂hub range shift 换档毂hub sleeve No 2 二号毂套humidity correction factor 湿度修正系数hydraulic tappet 液力挺柱hydraulic type 液力式Hydrocarb on measuri ng in strume nt 碳氢化合物分析仪Hydroge n flame ioni zati on detector 氢火焰离子化分析仪l/S locking rod内锁止拉杆l/S release rod内开启拉杆Identification Code 标t记idle fuel tube怠速油管idle fuel way怠速油道idle jet怠速喷口idle mixture screw怠速混合气调整螺钉idle tube 怠速油管idling operation 怠速工况Idling Speed 怠速ignition coil 点火线圈ignition coil type点火线圈类型ignition controler 点火控制器ignition key点火钥匙ignition module点火控制器ignition point 燃点ignition switch 点火开关Ign iti on System 点火系iqnition wire 点火线Illuminating axis 光照轴illu min at ing surface 透光面Illumination angle 入射角Illumination intensity 光照强度Illumination of the retro-reflecting device 回复反射装置的照度illuminations actually measured 实测照度Illuminometer 照度计IMPACT REDUCTION OF INSIDE REARVIEW MIRRORS 缓冲式室内后视镜IMPACT REDUCTION TYPE OUTSIDE REARVIEW MIRRORS 缓冲式后视镜Impact test冲击试验Impactor碰撞块IMPORTED MOTOR VEHICLE 进口机动车in connection with 与…有关inclination angle 倾斜角in dicati ng secti on 指示部分in dicator lamp 指示灯indicator lamp, left turn 左转向指示灯indicator lamp, right turn 右转向指示灯in directly con trolled wheel 间接控制车轮Infant-carrying vehicles 幼儿专用车information 资料in itial choke valve cleara nee 初始阻风门间隙initial inspection 初始检验Injection Nozzle 喷油嘴Injection Pump 喷油泵injector 喷油器in let进油口in let hole进气孔in let hose 进风口inlet ope ning 进油口in let tube进油管in let valve 进油阀Inner Dimension 内部尺寸inner shaft 内半轴inner tube 内胎input shaft 输入轴in put shaft, tranm issi on 变速器输入轴in put voltage输入电压In spect ion equipme nt 检验设备in spector检验人员in stall panel 安装板in strume nt cluster 组合仪表（盘）in strume nt harn ess 仪表板线束instrument illumination lamps 组合仪表照明灯in strume nt panel assy.仪表板总成in strume nt pan els 仪表板in take and exhaust device 进排气装置in take duratio n 进气持续角in take heater进气加热器in take ma ni fold 进气歧管lamp switch, 4WD四轮驱动灯开关lamp type 灯式Lap belt an chorages腰带固定装置Large-Sized Rear Reflex Reflectors 大型后回复反射器Large-sized special 大型专用latch assy. , frontRH. Door 右前门锁总成latch assy. , rear RH. Door 右后门总成lateral level横向水平仪lead ing shoe 领蹄Leaf spri ng 片簧left fog lamp 左雾灯left headlamp左前照灯left horn左喇叭left steeri ng 左转向left tail lamp 左尾灯lege nd图例Length of trochoid 旋轮线Length, Width and Height 全长、全宽、全高Lens配光镜lens, cluster 表蒙let in air 进气lever assy. , turn sig nal sta ndard 综合开关操纵杆总成lice nse lamp 牌照灯lift gate举升门liftgate assy.举升门总成liftgate latch assy.举升门锁总成liftgate lock assy.举升门锁芯总成light source module 光源模组Light Vehicles 轻型车辆Light-Exposure and Light-a nd-Water-Exposure Apparatus 光线暴露及光线与水暴露设备lighting device 照明装置Lighti ng System 照明系统Limit towards blue 趋蓝极限Limit towards red 趋红极限limiting valve body 限压阀壳体limiting valve spring 限压阀弹簧Linearity error 线性误差lining衬片link assy. of front stabilizer 前稳定杆连杆总成lin kage type 联杆式Liquefied Petroleum Gas-Fueled燃用液化石油气机动车load cell simulator载荷传感器模拟装置load sensing device负载感受装置Loaded goods 装载物loaded WT最大总质量Load ing Capacity 载重量Loading platform 货箱Loading platform offset 货箱偏移量Local Land Tran sport Office 地方陆运署Local Office 地方署Locati on of bus in ess place 业务场所地点lock CYL assy. , RH. door右车门锁芯总成lock piece, reverse gear 换档器锁片locking & indexing plate 锁止刻度盘Locking Device 锁止装置Lock ing system 锁止装置long axis 长轴Iong-body长车身Iongitudinal center 纵向中心Iongitudinal centerline 纵向中心线Ion gitudi nal pla ne 纵向平面Iongitudinally-mounted 纵向安装low fuel warning indicator bezel 低燃油报警灯框low fuel warning indicator lens 低燃油报警灯透片low fuel warning module低燃油报警组件low idle system 低怠速系统low range 抵挡low range lock plate 抵挡锁止板low speed jet彳氐速喷口lower con trol arm 下控制臂总成lower pressure switch 低压开关lubrica nt capacity润滑油加注油lubrica nts 润滑油Lubricating oil 润滑油lubricati ng system 润滑系luminance factor 亮度因数luminous flux 光通量luminous intensity 光照强度M / CYL / vacuum booster assembly制动主缸及真空助力器总成M/CYL push rod主缸推杆Magnification 增大率mai n beari ng 主轴承ma in beari ng journal cleara nee 主轴承间隙mai n beari ng journal diameter 主轴承轴径mai n beari ng journal width 主轴承宽度main body, conn ector 化油器中体mai nfold presure 歧管压力mai nfold vacuum 歧管真空ma in fuel system & vacuum reriched system 主油系及真空加泷系统Ma in hon eycomb block 主蜂窝块main injection jet 主喷口main jet主量孑Lmain oil gallery 主油道mai n spri ng 主簧Make and type厂牌和型号Management supervisor 主管人manual tran smissi on手动变速器，手排挡变速箱Manu facturer 制造者MANUFACTURER TEST 制9造者试验mapp ing瞬态性能mapp ing curve瞬态性能曲线marker lamp, left front 左前示廓灯marker lamp, right front 右前示廓灯mass flow rate质量流动速率master cylinder制动主缸，总泵，刹车总泵master cyli nder and vacuum booster制动主缸及真空助力器master cyli nder body 制9动主缸缸体master cyli nder cover 制动主缸缸盖mate合笼max gas direct 混合器走向max. amps最大电流MAX. power最大功率Max. torque最大扭距Maximum Loading Capacity 最大载重量maximum out-of round(all journals) 最大不圆度(所有轴径) maximum output 最大功率Maximum Stable Inclination Angle 最大稳定倾斜角maximum taper(all journ als)最大锥度(所有轴径) Maximum Torque 最大扭矩Measuri ng equipme nt 度量装备Measuri ng tape 卷尺mecha ni cal steeri ng 机械转向器media n seati ng pla ne 座椅中心面medical treatment and epidemics prevention vehicle医疗防疫车Meter仪表meteri ng rod 计量杆meteri ng rod arm 计量杆摇臂meteri ng rod arm assy.计量杆摇臂总成metering valve限流阀，限压阀micro-air direct微量空气走向microph one 话筒Middle density foam rubber 中密度泡沫橡胶min. output voltage at 1000r/mi n 1000r/mi n 最小输出电压min. rpm最小转速Minimum Grou nd Cleara nee 最小离地间隙Min i-sized 微型mini-sized motor vehicle 小型机动车Mi nister of Land, In frastructure and Tran sport 国土交通大臣Mi nistry of Land, In frastructure and Tran sport 国土交通省Min istry of Tran sport 运输省Mi nistry of Tran sport Ordi nance 运输省令notified motor vehicle获得认可的机动车NTSEL运输大臣Number of cyli nders 缸数Number Plate Lamp 牌照灯nut螺母nut, conn ect ing rod 连杆螺母nut, fron t output shaft 前输出轴螺母nut, jack sealed 插座螺母Observ ing an gle 观测角Observi ng axis 观测轴Observi ng pla ne 观测平面odograph记录仪Offset偏置量OFFSET COLLISION 侧面碰撞oil co ntrol 油环（槽）oil control rail 刮油环oil fill plug注油螺塞oil filter机油滤清器oil filter assy.机油滤清器总成oil gallery 油道oil pan油底壳oil path, bypass valve 旁通阀油道oil pressure gauge 油压表oil pressure gauge calibrati on 电压表电阻oil pressure relief 溢流压力oil pressure sen sor机油压力传感器oil pressure switch 油压开关oil pump机油泵oil pump & in let assy.机油泵与进油管总成oil pump assy.油泵总成oil seal油圭寸oil soaked clos ing magn etic path model 油浸闭磁路式OK ran ge合适范围on-board diag no stic 车载诊断on board diag no stic device 车载诊断设备opacimeter不透光式烟度计Ope n Flame Su nshi ne Carbo n-Arc Type 明焰日光碳弧灯型Opening roof 天窗Operati on con diti ons 运行状态Operational Limits 运行参数Ordin ary-sized 普通型O-ri ng, seal O型油圭寸Outer diameter 夕卜径outer tube夕卜胎outlet 出油口outlet of comb ined pump 复合泵出油口outlet ope ning 出油口outlet tube 出油管outlet valve 出油阀Outli ne Marker Lamps 示廓灯output shaft 输出轴overhead hoist 吊运装置overall dime nsions 夕卜形尺寸overall view 透视图Overhead valve 顶置气门overr unning clutch 单向啮合器P/S pump MTG bracket动力转向泵安装支架pad衬块panel damper仪表板风门Paper tape recorder 纸带记录仪Paragraph 项park brake level停车制动拉臂park brake switch 手制动开关park lamp, left front 左前小灯park lamp, right front 右前小灯Parki ng Brake驻车制动器park ing brake cable 驻车制动拉线park ing brake lever 驻车制动操纵杆Parki ng Brake System驻车刹车系统park ing lamp 驻车灯parking switch手制动开关Partial flow dilution 分流稀释particulate matter 颗粒物parts of heat ing & air con diti oning system 暖风系统部件Passe nger Accommodatio n 乘坐装置passe nger airbag deactivati on system乘客气囊禁用。
模具术语中英文对照 Mold
模具专业术语中英文对照模具Mold模胚Mold Base分模线Parting Base母模线Parting Line公模侧Core Side嵌板Mold Plate嵌件Insert滑块板Slider滑块板固定板Wear Plate斜针Angular Ejector组装板Back Plate第二固定板Runner Stripper Plate 顶针板Ejector Plate方铁Spacer Block定位圈Locating Ring导柱Guide Pin撑顶Support Pin定位杆Stop Bolt小拉杆Pull Bolt导柱套Guide Bush水口针Runner Lock Pin斜导柱Angular Pin锁定块Heal Block回针Return Pin垃圾针Stop Ring顶出板导柱Ejector Guide弹簧Coil Spring支撑柱Support Pillar顶针Ejector Pin板顶针Blade Ejector顶块顶出Block Ejector顶板顶出Plate Ejector司筒顶出Sleeve Ejector中心针Center Pin机嘴套Spure Bush直流道Sprue流道Runner支流道Drop 定位机构Inter Lock吊圈Eye Bolt日期转印Date Mark前模Cavity后模Core型心Core Pin出模编号Cavity Number冷却管Cooling Channel水嘴Hose Nipple冷却棒Baffle加热管Heat PipeO形圈O Ring逃气孔Air Vent销针Dowel Pin铣床加工Milling Machining放电加工EDM Machining线切割加工Wire Cutting磨床加工Grinding孔位加工Drilling细加工Deburring省模加工Polishing配模Fitting塞规Shim铜公EDM Master筋骨加工Rib Machining脱模斜度Draft Angle倒扣Under Cut钢材Steel咬花Texture雕刻加工Engraving电镀加工Electro Plating热处理Hardening氮化处理Nitrding表面处理Surface Hardness内六角螺钉Allen Bolt热流道Hot Runner热流道结构Manifold热嘴Hot Tip注塑Injection树脂Resin材料Material等级/类型Grade干燥Dry干燥不足Not Dried Enough收缩率Shrinkage充填Full Shot比重Density调温机Temp Cont Unit热可塑性Thermo Plastis热硬化性Thermo Set银条状Silver Line喷流痕Flow Mark侠水纹Weld Line披峰Burr缩水Sink mark烧焦Burn Mark充填不良Short Shot光泽不良Gloss Not Enough气泡Bloe Hole难型不良Sticking弯曲Bending变形Warpage光泽不均Uneven Gloss难物不良Black Spot打痕Damage顶白White Mark谬丝Hair Flash拉伤Scrtach油污点Oil Dirt裂化Crack倒塌Deform分模定位锁Parting Lock水口Gate点水口Pin Gate侧水口Side Gate潜伏水口Submarine Gate。
模具常用术语中英文对照表
”R，L Co.,Ltd" 模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料＃Cold Slag线切割Wire E。
D。
M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2—13 Eye Bolt 1/2—13Tap导柱位Leader Pin Location耐落胶Teflon Paste 偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰) Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut—Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub—Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball—Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B’Plate方铁(垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉(定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide—In Type Mold回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock —Out Plate电动安全开关Electrical—Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven 走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边) Angle PinA板 A’plateB板 B'plate倒扣Under—Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut—Off(S/0）导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary 丝印Silkprint不干胶Adhesive Sticker 导向针Guide Din公差Tolerance线切割Wire-Cut 电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫(限螺丝） Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold 剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司 EJ.GUIDE PIN。
模具通用语中英文对照
X:-（避空孔,反面CNC单+0.00,锣深0.00)
(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)
(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)
(反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)
(￠0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)
ream
铣
mill
车
lathe
电脑锣
NC mill
线切割
wire cutting(W/C)
磨
grind
刨
planer
电火花
EDM
镭射
laser cutting
倒角
chamfer
xx的精加工
finish XX
真空热处理
vacuum heat treatment
镀钛
TD coating
退磁
demagnetization
(反面沉头￠0.00*0.00深)
(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)
(侧面沉头￠0.00*0.00深)
(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)
X:-M0.00钻穿,反面攻深0.00,有效牙0.00
X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)
X:-M0.00盲孔,正反面攻深0.00，有效牙0.00
模具专业词汇中英文对照
模具专业词汇中英文对照中文英文中文英文中文凸模punch拉延模drawing die材料凹模die切边模triming die板料压边圈binder（Blankholder）翻边模flang die外板件压料器PAD整形模restrike die内板件氮气缸Gas cylinder分模线punch profile基准孔料厚限位块Balancer block下料模blank die一般孔打死块Bottom block斜锲CAM制造滑板Wear plate拉延面die face数控加工导柱Guide post翻边线Flange line铸造导套Guide bush切边线Trim line厚度铸件casting孔径/孔位Holes dia & position试模拉延筋Draw bead夹具孔Joggle position热处理Heat treatment顶杆孔cushion (Air) pins排气孔Air vent hole标准件Standard parts到底标记bottomingmark冲压方向Pressing direction铸件镶块Cast steel送料方向feed direction锻件镶块Steel insert type背推back up堆焊Weld bolt材料 material定位销dowel废料Scrap cutter减轻孔lightening hole球锁冲头Ball lock punch冲孔pierce冲孔凹模button die废料盒Scrap box侧销SIDE PIN回程钩positive return英文material blankouter panel inner panel Manufacture CNC casting Thickness try-out。
中英文模具术语
Stick topost 粘柱Witness line夹线Pin pointgating细水口Ejector pin顶针Thermal pin散热针Ejector retainerplate顶针面板Eyebolt hole/safety hoisthole吊模孔washer垫圈Switchcop 开关盖Hot stmping烫金Edge gating边入Ejector sleeve同筒baffle水隔片Rrecyclingsymbol胶料代码Socket head capscrew(S.H.C.S)胚头螺丝Shrinkingrate顶白rib 骨位harden淬硬Ejector plate顶针底板Ejector blade扁顶针O -ring密封圈Double ejection二次顶出Spherical radius for spruebushing唧嘴球面半径Materialrecycle胶料回收代码Stick tocore 粘哥Pad printing移印Stripper plate推板Sprue pullerpin水口顶针Stop pin垃圾钉Stripper ejection推板顶出Socket head stripper bolt限位螺栓Bottomhouse底壳Sinkmark 缩水印spraying喷油Taperinterlock啤把锁Feed pin入水针Cross rib十字骨Runner tripperplate水口推板Back (moving)clampplate后码模板Top house面壳常用词语中英对照表Batterydoor 电池门Fan gating扇形入水Pry bar slot开模坑Venting pin放气针Flat head capscrew平头螺丝Silk screenprinting丝印High temperatureinsulator shee t高温绝热板Sandblasting喷砂Pin mark 拖花Support pillar模鼎Clampingslot码模坑slider行位Cavity insert模肉Leader pin /guidepin边钉Water channel/weaterlines运水Dowel pin管边Stressmark 拖白boss螺丝柱Locating ring定位法兰Angle pin/hornpin斜边Core insert哥肉Safetystrap/transit strap锁模片Knock-out extensionadapter螺丝套镶件Edm master铜公Shut-kff 碰穿undercut倒扣Spruebushing唧嘴Wear plate耐磨片Sub-insert镶件Brass pressureplug喉塞Straight bushing/shoulderbushing边司Stick tocavity粘模fiashing 披锋Gating dimple入水凹位Pre-harden预硬Slider retainer行位定位夹Core pin镶针Part line/partingline分模线Ball plungers定位波子（弹弓波子）Air runner nitride Beryllium Weld line /kint Stationary Limit witch/micro-switchtrapping 困气水口氮硬copper铍铜line熔合线/夹水线side(A-plate)前模限程开关制Burned mark 烧焦痕Runnershut-off水口开关Chromeplating镀铬Lifter/raiger斜方/推方Movingside(B-plate)后模Hot sprue bushing电热咀Guided ejdction bushing中托边司Moldbase 模胚Cold slug well冷料槽Silverstreaking银线Latch lockassembly勾鸡Shoulder leaderpin有托边钉Coil heater螺旋状发热丝Front(stationary)clampplate前码模板gusset 火箭骨Gating dimple入水位nameplate产品铬牌Hydrauliccylinder油唧筒Nickel plating镀镍Hot runner system热流道Tunnel gating/subgating潜水Directgating 大水口Therno-couple恒温线Return pin回针tip端部喷咀engraving雕刻Manifold plate热流道板Date iinsert日期镶件Lap join 搭接口Stick to slider粘行位Splay/blashmarkJiffy-tite plug喉咽Spacer block方铁Photo-etchingtextureRecycling insert胶料代码镶件气纹蚀纹。
模具常用语中英文对照
限位柱
stop block
起吊孔
handing hole
起吊环
eyebolt
靠块
heel
脱料拉杆
spool
模座导正块
thrust heel
种类
中文名称
英文名称
中文名称
英文名称
零
件
类
耐磨片
wear plate
垫片
shim
压块
keeper
初始管位
first start pin
键槽
stripper
下模板
die plate
冲头
punch
凹模
die
零
件
类
浮块
lifter
浮料板
lifter plate
成型公
form punch
压料块
pressure pad
切边冲头
trim punch
刀口
trim steel
沉头孔
counter bore
冲孔入子
button
顶针
kick off / ejector
key slot
键
key
氮气弹簧
nitrogen spring
螺旋弹簧
coil spring
聚氨酯弹簧
urethane
导柱
guide post
导套
guide bushing
插针
pilot pin
插针套
pilot bushing
侧刃
french
传感器
sensor
销
dowel
螺丝
screw
拔牙
模具常用语中英文对照讲解
种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transfer die 下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die工序类料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄coin成形form 侧成形cam form 整形restrike 围边flange打凸米boss / dimple 打凸包emboss打字印stamp 打沙拉孔hourglass 面押coin burr 抽孔extrude hole 拍平flat 卷圆curl种类中文名称英文名称中文名称英文名称工序类旋转rotate 铆接rivet产品切边线trim line 铆螺母stake nut 切断cutoff 接刀口mismatch 料带带料处carrier tab 毛刺方向burr direction 压线groove 下料blanking模板类上托板top plate 下托板bottom plate 上垫脚upper parallel 下垫脚lower parallel 上模座upper die set 下模座lower die set 上垫板punch backup 下垫板lower backup 上夹板punch holder 下夹板die holder 上脱料板stripper 下模板die plate 冲头punch 凹模die零件类浮块lifter 浮料板lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 沉头孔counter bore 冲孔入子button 顶针kick off / ejector 废料切断刀slug breaker 成型凹模forming die 整形公restrike punch 导尺rail 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert侧冲组件cam 滑块slide滑块上油槽oil groove 铲机driver码模槽mounting slot 储运块storage block 限位柱stop block 起吊孔handing hole 起吊环eyebolt 靠块heel脱料拉杆spool 模座导正块thrust heel种类中文名称英文名称中文名称英文名称零件类耐磨片wear plate 垫片shim压块keeper 初始管位first start pin键槽key slot 键key氮气弹簧nitrogen spring 螺旋弹簧coil spring聚氨酯弹簧urethane导柱guide post 导套guide bushing 插针pilot pin插针套pilot bushing 侧刃french传感器sensor 销dowel螺丝screw 拔牙jackscrew垫圈washer 盲销blind dowel压毛边冲头deburring punch 挡块stopping plate压线冲头groove punch 定位块location block字模冲头stamp punch 圆冲头round punch压筋冲头ribbon punch 气垫板air cushion plate 异形冲头special shape punch 气垫顶杆air-cushion eject-rod 切边冲头trimming punch 上压块pressure block加强筋冲头stiffening rib punch 弹簧箱spring box 定位板guide plate 弹簧箱顶杆spring-box eject-rod 压边圈binder 弹簧箱顶板spring-box eject-plate公差类公差tolerance 公差范围tolerance range 上公差upper tolerance 下公差lower tolerance 公差+/- 0.05 plus minus 0.05 形位公差图GD&T 平面度flatness 直线度Straightness 倾斜度angularity 垂直度perpendicularity 平行度parallelism 圆度roundness种类中文名称英文名称中文名称英文名称公圆柱度cylindricity 面轮廓度surface profile差类线轮廓度line profile 位置度true position 同轴度concentricity 对称度symmetry 圆跳动runout 全跳动total runout 尺寸dimension 角度值angle degree 尺寸全检报告dimensional layout 三次元尺寸报告CMM report冲床相关机械冲床mechanical press 油压机hydraulic press 吨位tonnage 行程stroke / travel 冲床上台面ram 冲床下台面bolster冲床台面布置图press layout 冲床上的快速对正QDC 冲床气垫air cushion 码仔stirrup 闭合高度shut height T型槽T-slot送料机feeder 送料高度feeding height工具卡尺caliper 千分尺micrometer 直尺ruler 高度尺height gage 丝攻screw tap 起子screwdriver 拨牙器jacker 扳手wrench风磨机hand grinder 油石oil stone加工类开料cutting material 钻drill (DR) 攻牙tap 铰ream铣mill 车lathe电脑锣NC mill 线切割wire cutting(W/C) 磨grind 刨planer电火花EDM 镭射laser cutting 倒角chamfer xx的精加工finish XX真空热处理vacuum heattreatment镀钛TD coating 退磁demagnetization 烧焊weld4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处外导套OUTER GUIDE BUISHING 起吊杆HANDING PIN实数铣通MILL THRU 正反两面各铣TOP SIDE AND OPP SIDE MILLX:-￠0.00（氮气弹弓过孔，锣穿）单+0.00X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（合销孔,铰)X:-￠0.00 (REAM FOR DOWEL)X:-￠0.00（合销孔,割)单+0.00X:-￠0.00 (W/C FOR DOWEL) S+0.00(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)(反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（合销孔,钻穿)X:-￠0.00 (DR.THRU FOR DOWEL)X:-￠0.00（一般孔,钻穿)X:-￠0.00 (DR.THRU HL)X:-￠0.00（穿丝孔,钻穿)X:-￠0.00 (DR.THRU FOR WEDM S.H.)X:-￠0.00（漏油孔,钻穿) 按向视图加工X:-￠0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-￠0.00（基准孔,铰)X:-￠0.00 (REAM FOR DATUM HL)X:-￠0.00钻穿（螺丝过孔)内攻M0.00牙X:-￠0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)(侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00（拨牙螺丝孔，攻穿）X:-M0.00 TAP.THRU FOR JACK SCREWX:-￠0.00（塞打过孔,钻穿)X:-￠0.00 DR.THRU FOR SPOOLX:-￠0.00（弹弓过孔,钻穿)X:-￠0.00 DR.THRU FOR SPRINGX:-￠0.00（弹弓孔,反面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00)X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 OPP SIDE)X:-￠0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE)X:-￠0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-￠0.00（两用销过孔,割)单+0.00X:-￠0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00) X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（浮块孔,割）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-￠0.00（顶针孔,钻穿)（反面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（顶针孔,钻穿)（正面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-￠0.00（导柱（导套）孔,CNC锣)单+0.00X:-￠0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-￠0.00（导柱（导套）孔,割)单+0.00X:-￠0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00)(阴影部分正面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE)(阴影部分反面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE)X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00)(阴影部分扣位正面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE)(阴影部分扣位反面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE)(正面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)注: 此处的沉头不能用C'BORE, 只有圆形的沉头才用C'BORE.(反面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-￠0.00（插针孔,铰)单+0.00X:-￠0.00（REAM S+0.00 FOR PILOT PIN)X:-￠0.00（插针孔,割)单+0.00(正面沉头￠0.00*0.00深)X:-￠0.00（W/C FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-￠0.00（插针孔,钻穿)(正面沉头￠0.00*0.00深)X:-￠0.00（DR.THRU FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-（冲头过孔,割)单+0.00(正面避空，CNC单+0.00，锣深0.00)(阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL)(POCKET, CNC DP 0.00 S+0.00 TOP SIDE)(POCKET SHADE FOR HEAD, DP0.00 TOP SIDE)X:-（冲头过孔,锣穿)单+0.00(正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU.FOR PUNCH CLEARANCE HL)(POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00(双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00) X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-￠0.00（冲孔漏屎,钻穿)X:-￠0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-￠0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30º锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE)X:-（漏屎斜度，直x斜45º锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)反面沉深底面留0.00MILL UNTIL DP正面沉深底面留MILL UNTIL DP五金模具单词总结模具种类:连续模progressive die机械手transfer die手动机械手hand transfer die单工程模single die/line die复合模compound die铆接模riveting die铸造结构模cast die能快换的模changeover die泡沫模pattern互换性:公差tolerance上公差upper tolerance下公差lower tolerance公差范围tolerance range公差+/- 0.05 plus minus 0.05形位公差图GD&T平面度flatness直线度straightness倾斜度angularity垂直度perpendicularity / squareness平行度parallelism圆度roundness / circularity圆柱度cylindricity面轮廓度surface profile线轮廓度line profile位置度true position同轴度concentricity对称度symmetry圆跳动runout全跳动total runout尺寸dimension角度angle degree全尺寸报告dimensional layout工艺性:料带strip料带图strip layout工序process冲导正孔pilot pierce冲孔pierce侧冲cam pierce切边notch成形后的切边trim切侧刃french trim / fringe trim 厚料切边后的精修边shave折弯bend墩薄coin折弯处压筋gusset成形form侧成形cam form整形restrike / rehit围边flange压线/压长条状筋ribbon打凸米boss / dimple打凸包emboss打字印stamp打沙拉孔hourglass面押coin burr抽孔extrude hole拍平flat / spanking包边hem edge压角cone张角flare切舌lance半剪knockout卷圆curl/热恶劣旋转rotate铆接rivet铆螺母stake nut切断cutoff接刀口mismatch料带带料处carrier tabs毛刺方向burr direction产品切边线trim line模具零件:模具die / tool上托板upper mounting plate 上垫脚upper parallel上模座upper die set上垫板punch backup上夹板punch holder止挡板traveling stop脱料板stripper下模板die plate下垫板die backup plate下模座lower die set下垫脚lower parallel上托板base mounting plate浮块lifter浮料板lifter plate成型公form punch压料块pressure pad切边冲头trim punch刀口trim steel刀口直身位land直5斜1 5mm Land 1 taper 刀口上沉头的深度die life 沉头counter bore冲头倒斜shear高低冲stagger punch球锁冲头ball-lock punch球锁座ball-lock retainer冲孔入子button顶针kick off / ejector废料切断刀slug breaker成型凹模form die整形公restrike form punch 导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate镶件/入子insert侧冲组件cam滑块slide滑块上油槽oil groove铲机driver码模槽mounting slot储运块storage block限位柱stop block起吊孔handing hole起吊环eyebolt模柄shank靠块heel摆块rocker bender脱料板拉杆stripper bolt模座导正块thrust耐磨片wear sheet耐磨板wear plate垫片shim两用销lifter pin初始管位first start pin内限位standoff压块keeper导柱导套压块keeper/ boss 键槽key slot键key氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange 氮气弹簧系统nitrogen manifold螺旋弹簧coil spring聚氨酯弹簧urethane弹簧套spring cage导柱guide post导套guide bushing插针pilot pin插针套pilot bushing插针通孔pilot through hole侧刃french误检装置misfeeder传感器sensor误检杆trigger油嘴oil nipple销针dowel pin螺丝screw牙thread拔牙jackscrew内六角螺钉socket head screw垫圈washer螺塞screw plug盲销blind dowel行程,走位stroke / travel吨位tonnage机械冲床mechanical press油压机hydraulic press冲床下台面bolster冲床上台面ram冲床台面布置图press layout冲床码模槽press mounting slot冲床气垫air cushion码模钳stirrup闭合高度shut height送料高度feeding height送料机feederT型槽T-slot避位clearance /pocket掏空pocket挂台head扣位pocket of head通气孔air vent hole漏油孔drain hole漏料孔slug hole基准孔datum hole通孔through hole穿丝孔first wire holeT型槽T-slot拔牙jackscrew摆块rocker bender闭合高度shut height避位clearance /pocket侧冲组件cam侧刃french插针pilot pin插针套pilot bushing插针通孔pilot through hole铲机driver沉头counter bore成型凹模form die成型公form punch冲床码模槽press mounting slot冲床气垫air cushion冲床上台面ram冲床台面布置图press layout冲床下台面bolster冲孔入子button冲头倒斜shear初始管位first start pin储运块storage block穿丝孔first wire hole传感器sensor弹簧套spring cage氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange氮气弹簧系统nitrogen manifold刀口trim steel刀口上沉头的深度die life刀口直身位land导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate导套guide bushing导柱guide post导柱导套压块keeper/ boss垫片shim垫圈washer顶针kick off / ejector吨位tonnage废料切断刀slug breaker浮块lifter浮料板lifter plate高低冲stagger punch挂台head滑块slide滑块上油槽oil groove机械冲床mechanical press基准孔datum hole键key键槽key slot聚氨酯弹簧urethane靠块heel扣位pocket of head两用销lifter pin漏料孔slug hole漏油孔drain hole螺塞screw plug螺丝screw螺旋弹簧coil spring码模槽mounting slot码模钳stirrup盲销blind dowel模柄shank模具die / tool模座导正块thrust内六角螺钉socket head screw 内限位standoff耐磨板wear plate耐磨片wear sheet起吊环eyebolt起吊孔handing hole切边冲头trim punch球锁冲头ball-lock punch球锁座ball-lock retainer上垫板punch backup上垫脚upper parallel上夹板punch holder上模座upper die set下托板base mounting plate 上托板upper mounting plate 送料高度feeding height送料机feeder掏空pocket通孔through hole通气孔air vent hole脱料板stripper脱料板拉杆stripper bolt误检杆trigger误检装置misfeeder下垫板die backup plate下垫脚lower parallel下模板die plate下模座lower die set限位柱stop block镶件/入子insert销针dowel pin行程,走位stroke / travel压块keeper压料块pressure pad牙thread油压机hydraulic press油嘴oil nipple整形公restrike form punch 直5斜1 5mm Land 1 taper 止挡板traveling stop机加工:开料cutting material钻drill (DR)攻牙tap铰ream铣mill车lathe电脑锣NC mill线切割wire cutting (W/C)磨grind刨planer电火花EDM镭射laser cutting倒角chamfer精加工finish XX真空热处理vacuum heat treatment镀钛TD coating退磁demagnetization烧焊weldG :40-M6BLIND HL,TAP DP18.00 OPP SIDE,THR DP18.00) 盲孔，反面攻深**G10:4-M30BLIND HL,TAP DP18.00 EDGE SIDE)盲孔，侧攻深**(%%c34.00*14.00 C'BORE DP14.00 TOP SIDE) 正面沉头多少×多少深G2 :24-%%c8.00(REAM FOR DOWEL WORK DP16.00 OPP SIDE,DR%%c6.00 HL)G2 :24-%%c8.00(合销,背铰深16.00,有效深,内钻%%C6.00通孔)G4 :3-%%c10.00(基准孔,背铰深20.00)背面锣25.00*25.00方形沉头，深1.00%%P0.01 (REAM FOR DATUM HL DP20.00,MILL25.00*25.00 OPP SIDE DP1.00%%P0.01)M:2-%%c15.00(弹簧孔,锣深33.00) (C'BORE OR SPRING DP33.00 TOP SIDE,WORK DP33.00)X :3-%%c32.00(导套孔,锣穿,单+0.01)(MILL THRU FOR GUIDE BUSHING S+0.01)G :2-M10盲孔,侧攻深30.00(有效深)(BLIND HL,TAP WORK DP30.00 EDGE SIDE)(沉头5.20%%P0.05深)(SLOT DP5.20%%P0.05 TOP SIDE)L :2-%%c8.000(合销,割)单+0.005 (W/C FOR DOWEL)S+0.005盲孔,攻深20.00(有效深) (BLIND HL,TAP DP20.00 TOP SIDE,THR DP20.00)(插针孔,割,单+0.01) (W/C S+0.01 FOR PILOT PIN)(避位孔,背锣9.80(有效深) (POCKET,MILL DP9.80 OPP SIDE WORK)(冲头过孔,锣穿) (MILL THRU FOR PUNCH CLEARANCE HL)(导柱孔,锣穿,单+0.005) (MILL FOR GUIDE PIN) S+0.005避位槽,背锣深19.00) (POCKET,MILL DP15.40 OPP SIDE)(背,沉头%%c14.00，掏深留11.00) (%%c14.00 C'BORE UNTIL DP14.00 OPP SIDE)下模刀口，实数割，直5斜1.5 （内钻%%C5.0穿丝孔）W/C S+0.00 TRIM STEEL,5.0LAND 1.5TAPER,(DR THRU%%c3.00 WEDM S.H)(MILL FOR INSERT DP30.0%%P0.01 S+0.01)(入子槽,锣深30.00%%p0.01,单+0.01)(氮气槽,背锣深4.00%%P0.1,单+0.1) (GAS SPRING MILL DP4.00 OPP SIDE)S+0.1按向视图加工ACCORDING VIEW DRAWING TO MACHINING试模材料:热扎板HRS (hot-roll steel)冷扎板CRS (cold-roll steel)不锈钢板Stainless steel镀锌板galvanized steel镀铝锌板galvalume steel热扎酸洗板HRPO steel (hot-rolled pickled and oiled steel)工具:卡尺caliper千分尺micrometer拨牙器jacker扳手wrench丝攻screw tap起子screwdriver码模钳stirrup设备/工具:3D Programmable CMM三次元检测仪3D CMM Beam Drilling Machine摇臂钻Bench Drilling Machine钻铣床Caliper卡尺CNC EDM电火花机CNC Machine Center加工中心CNCCNC Milling Machine数控铣床CNCCNC Planer Type Milling Machine龙门刨铣床Hardness Tester硬度计Height Gauge高度仪High Wire Cutting快走丝Hole Puncher 打孔机Horizontal surface grinder小水磨/卧式平面磨床Horizontal surface large grinder大水磨Lathe车床Measurement Surface Plate测量平台Metal Saw Machine锯床Milling Machine铣床Oil Press油压机Pin Gauge标准针规Plastic Injection Machine注塑机Point to Point CMM三次元测量仪Precision surface grinder精密手摇磨Press冲床Projector profile投影机Shear Press剪板机Slow Wire Cutting慢走丝Vertical Milling Machine卧式强力铣床扳手wrench拨牙器jacker卡尺caliper码模钳stirrup起子screwdriver千分尺micrometer丝攻screw tapCARVE 雕刻pothook 挂钩SPECIAL HL 异形孔漏斗 filler角铁 ANGLE IRON展开 expanding微调开关 INCHING SWITCH合叶 HINGE优力胶 RUBBER球锁垫板 LOCK WASHER双线边刀口,不倒角TRIM STEEL NEAR THE DOUBLE LINE NO CHAMFER滑块座:SLIDE SET机械:（engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料13-mode 13工况3rd gear 三档齿轮3-way seat 三向座椅4WD control device 四轮驱动控制装置4WD indicator switch 四轮驱动指示灯开关4WD lamp electrical connection 四轮驱动指示灯接线4WD switch 四轮驱动开关5th synchromesh assy. 五档同步器总成6PK belt 6PK 多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy. 空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator interlocking type 加速踏板联锁式accounting foundation 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter 连接器additional features 附加装置additional rule 附加法规adjust screw 调整螺钉adjuster cable 调整拉线adjuster plug 调整盖adjuster screw assy. 调整螺栓总成adjuster washer 调整棘片adjuster, diff. bearing 差速器轴承调整螺母Adjustment system 调节装置Administration and Registration Division 管理科Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts Which Can Be Fitted and/or Be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of These Prescriptions关于对轮式车辆、安装和/或用于轮式车辆的装备和部件采用统一条件并相互认可基于上述条件批准的协定书Agreement Regulations 协定法规air cleaner 空气滤清器air cleaner assy. 空气滤清器总成air cleaner cartridge 空气滤清器滤芯Air compressor 空压机air condition compressor 空调压缩机air direct 空气走向air filter 空气滤清器air flow 空气流向Air flow meter 空气流量计air jet 空气量孔air metering hole 空气量孔air path 气道Air Pressure of Tire 轮胎气压Air type 空气型air valve 空气阀air-cooled 风冷Aisles 通道Alcohol 酒精all bearing 球轴承alternater bracket 发动机支架alternator 交流发电机alterntor assembly 交流发电机总成alumininum-rim 铝合金钢圈alumininum opposed model 铝制对开式AM/FM cassette stereo radio 调幅/调频立体声收放机ambulance 救护车Amended by 修正文amount of exhaust emission 排气排放量Amplitude resolution 幅度分辨率Analogue magnetic recorder 模拟式磁记录仪ANALYZER 分析仪anchor plate, brake caliper 制动钳安装支架Anchorage 座椅固定装置Angle of divergence 偏离角Angle of rotation 旋转角angles drift off vertical line 指针偏离垂直线的角度Angular diameter of the retro-reflecting device 回复反射装置的角直径annex 附件Announcement 公告anti, shutdown screw 防不灭车调整螺钉Antilock Brake System 防抱死制动系统appendix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant 申请人application 申请application for notification 认可申请书approval 认可arm, valve rocket 摇臂armature 转子总成armature shaft 电枢轴Arm-rests 靠手Article 条Article 1 第1条Asphalt solution 沥青溶剂Attached document 附署文件attached sheet 附表Attached Table 附表attaching location of seat belt anchorage 座椅安全带固定装置的固定位置attachment 附属文件Attendants onboard 车上值班人员automatic chock cover setting 自动阻风门盖调到automotive electric system 汽车电系automotive engine system 引擎系统automatic transmission 自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 副簧Auxiliary Stop Lamp 辅助驻车灯axle case 桥壳axle case assy. 桥壳总成axle ratio 桥速比axle tube 桥管axle weight 轴重back angle level 靠背角水平仪back angle quadrant 靠背角量角器back pan 靠板back spring 回位弹簧backing plate 制动底板Backing sheet 衬背板Back-Up Light 倒车灯backup washer 支撑挡圈bail wire 卡紧环balance tube 平衡管ball 钢球ball bearing 球轴承ball joint assy. , upper 上球销总成ball valve 球阀ball valve, inlet 进油口球阀bar 拉杆barrier 障碍壁battery 蓄电池battery terminal 蓄电池接线柱bearing cap 轴承盖bearing cover, input shaft 输入轴轴承盖bearing, connecting rod 连杆轴承bearing, input shaft 输入轴轴承Bed for babies 婴儿床bell 带束层bench seat 长条座椅berived cap 轴承盖bezel assy. 框板总成bezel, cluster 表框be pilot 小批量产品blead door 混合风门bleeder screw 放气螺钉blower assy. 鼓风机总成blower motor 鼓风发电机blower resistor 鼓风机电阻blower switch 鼓风机开关body 车身,阀体body & liftgate assembly 车身和举升门总成body assy. 车身总成body block 人体模块body of A/C & heater 空调加热器壳体bolt 主缸连接螺栓bolt, connecting rod 连杆螺栓Booster 助力器boot 护罩BOSCH starter motor assembly “波舍”起动机总成bottle assy. , coolant recover 冷却液回收罐总成bottom houseing, fuel pump 燃油泵下壳体bottom housing, fuel tank 燃油箱下壳体bracket 支架bracket assy. , spring seat 弹簧座支架bracket, steering damper mounting 转向减振器支架brake alarm lamp 制动报警灯brake alarm lamp switch 制动报警灯开关Brake booster 制动助力器brake caliper 制动钳brake caliper assy. 制动钳总成brake caliper piston 制动钳活塞brake combination valve 制动组合阀brake disc 制动盘Brake drum 制动鼓brake fluid 刹车油Brake hose 制动软管brake lining 刹车来令brake line, LF 左前制动油管brake line, RF 右前制动油管brake oil flow 制动液流向brake paddle 制动踏板brake pedal 制动踏板Brake pipe 制动管brake shoes 刹车蹄片brake shoe 制动衬块Brake System 制动系Brake Systems for Tractors and Trailers 牵引车及挂车的制动装置Brake tester 制动器试验台brake valve 制动阀brake warning lamp 制动报警灯brake warning switch 制动报警开关Braking efficiency 制动效能braking force control system 制动控制装置Braking wheel 制动轮branch office 分署breaker 断电器bridge 过桥broadcasting vehicle 广播车brush 碳刷总成Buckle 带扣bulkhead 隔板Bulldozer 推土机bumper 保险杠Bumper element 保险杠构件bus transfer 车辆转移台bushing 衬套bushing, upper control arm 上控制臂衬套Business Place 业务场所bypass valve 旁通阀Cabinet Decision 内阁决议cable guide 拉线导向块cable-operated control system 液压式离合器系统Calibration factor of a data channel 数据通道校正系数calibration gas 标定气体calibration method 标定方法caliper assy. , front brake 前制动钳总成Camber 外倾camber angle 前轮外倾角camshaft 凸轮轴camshaft oil gallery 凸轮轴油道cap 加机油口盖cap assy. , power steering fluid reservoir 动力转向液油罐盖cap assy. , radiator 散热器盖总成cap screws 螺钉cap, connecting rod 连杆盖Capacity 容量,规格Capacity of the fuel tank 燃油箱容量capillary tube 毛细管carbon brushes & brush holder 电刷支架总成Carbon monoxide measuring instrument 一氧化碳分析仪Carburetor 化油器carburetor assy. 化油器总成carburetor bowl 化油器浮子室carburetor bowl vent system 化油器浮子室通风系统carburetor overhaul scheme 化油器分解图carburetor working scheme 化油器工作示意图carcase 胎体case runout (Max.) 差速器壳圆跳动（最大）Caster 后倾Catalyst 催化器category 类别cement and aggregate 水泥和混凝料Centreplane of occupant 乘员中心面Certified 经认证的Cetane number 十六烷值chain 驱动链chain drive 驱动链Channel amplitude class 幅度级通道Channel Frequency Class 频率级通道chassis 底盘chassis dynamometer 底盘测功机chassis shuttle 底盘平移台chassis number 底盘号Check and Maintenance 检查和保养check assy. , front door 前门限位器总成check assy. , rear door 后门限位器总成check ball 回止球check bracket 限位器支架check nut 限位器螺母check valve 单向阀check valve hole 回止阀孔check valve retainer 单向阀保持架check valve spring 单向阀弹簧check weight 回止块Chigi Circular No. 地技第…号Chigi No. 地技第…号Child Restraints 儿童约束装置chime module 蜂鸣器Chishin Circular No. 地审第…号Chishin No. 地审第…号chock heater 阻风门加热器总成chock plate 阻风门chock unloaded 阻风门连动装置choke 阻风门choke device 阻风装置choke unload mode 阻风门卸载状态cigarette lighter 点烟器circuit breaker, wiper/washer 刮水器/洗涤器电器断路器Circular 通告circular notice 通告clamp 卡圈Clamp ring type 锁紧圈式Cleaning efficiency 清洗效率Cleaning period 清洗周期clearance 最小离地间隙Clearance Lamp 示廓灯clinder head 气缸盖clip 卡子cluster housing 组合仪表壳Clutch system 离合器clutch assembly 离合器总成clutch control device 离合器控制装置clutch disc,clutch 离合器片clutch housing 离合器壳clutch master cylinder 离合器主缸clutch working cylinder 离合器工作缸Coating 涂层Code No. 型号Code of Federal Regulations 美国联邦法规总览Coefficient of luminous intensity (CIL) 亮度系数coil spring 圈状弹簧cold air 冷空气cold cranking voltage(min.) 最小冷启动电压collapsible spacer 可压缩隔垫collector 拼装台colorimeter 色度计coloured-light unit 有色灯光组column assy. 转向管柱总成combination brake switch and proporting 组合阀combined lamp 复合灯combined pump 复合泵combined pump diaphragm 复合泵膜片combined pump diaphragm rod 复合泵膜片杆combined pump lifter link 复合泵举升拉杆combined pump move direct 复合泵运动方向Combustion Chamber 燃烧室commutator 换向器compensate opening 补偿孔completion inspection certificate 终了检验证书Completion of notification 完成认可compressor 压缩机compression (both) 气环槽（两个）compression ignition type 压燃式Compression ratio 压缩比concrete mixer truck 混凝土搅拌车condenser 冷凝器condenser assy. 冷凝器总成conduit pipe 导管cone , diff. side bearing 差速器轴承，内圈带滚子cone, pinion front bearing 主动齿轮前轴承内圈带滚子cone, pinion rear bearing 主动齿轮后轴承内圈带滚子Confirmor 确认者connecting rod 连接杆connecting link 连接杆connecting rod journal diameter 连杆轴径connecting rod journal width 连杆轴径宽度connecting rod throttle 连杆喷油孔connector 连接器connector of service valve 维修阀接口Constant speed 等速construction and device 结构和装置control & tube assy. , hyd clutch 离合器工作缸和油管总成Control System 操纵系control valve 控制阀阀门control valve model 控制阀型式control valve seat 控制阀阀座convex plate 凸台cooling fan 冷却风扇cooling system 冷却系统Cornering Lamp 转弯灯corrected 修正的cotter 开口销counter 5th gear 中间轴五档齿轮counter shaft 中间轴coupled condition 连接状态Coupling Device 牵引装置cover 端盖cover & plate assy. 离合器盖及压盘总成cover assy. , air cleaner 空气滤清器盖总成cover, gear 侧盖cover, heater air 空气加热罩cover, rear axle case 后桥壳盖crane vehicle 起重车crankcase 曲轴箱crankshaft 曲轴crankshaft gear 曲轴齿轮crankshaft & connecting 曲轴连杆机构crankshaft oil gallery 曲轴油道crankshaft sprocket 轴承链轮critical flow 临界流Cross sensitivity of a linear transducer 线性传感器的横向灵敏度Crush distance 压碎距离Crush rate 压碎速率Crush Strength 压碎强度Cumulative time 累计时间cup 皮碗cup, diff. side bearing 差速器轴承外圈cup, pinion front bearing 主动齿轮前轴承外圈cup, pinion rear bearing 主动齿轮后轴承外圈Cut-off 明暗截止线cycle 冲程cyclinder head cover 气门室罩Cylinder 气缸cylinder block 汽缸体cylinder body 缸体Cylinder bore 缸径cylinder head 汽缸盖cylinder head cover 气门室罩cylinder number 气缸数cylinder working order(clockwise) 气缸工作顺序（顺时针）damper 转向减振器dangerous article 危险物darkroom 暗室Data channel 数据通道Data Processing 数据处理Date of notification 认可日期Deceleration of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster 除霜器dehydrator 储液器和干燥器。
模具常用术语中英文对照表
"R，L Co.,Ltd"模具常用术语中英文对照模芯 Parting Core 局部视图Partial View 冷料# Cold Slag线切割 Wire E.D.M 轮廊Contour 螺纹孔 Tapping Hole连接件 Fittings 斜针 AnglePin 接合 Engage 替 换 镶 件InterchangeableInserts 指定吨位的注塑机Specific水嘴接头 Water Fittings 漏水测试 Leak Test流道排气 Runner Vents抛光 Draw Polish螺纹 Eyebolt Thread侧抽芯 Side Action回针 Stop Pin二级顶出针 Sub-Leaderd Pin镶件 Mold Insert加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary名称块表 Title Block版本标识 Revision Level材料清单 Stock ListMold 制模 Build Mold手动滑块 Hand Slide Press加强筋Reinforcing三角撑Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handling Hole 运输安全带Moldstrap 码模槽Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位Leader Pin Location 耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel 倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate 环保印Recycling Insert后模镶针Core Pin 气顶Air Poppet Valve拉圾钉Stop Pin 截水口镶件Runner Shut-Off Insert 有托顶针Shoulder Ejector Pin 早回Early Ejector Return 顶针板导套G uided Ejection Bushing 加速项Accelerated Ejector针板导柱Guided Ejection Leader 客户ClientPin产品名Part Name唧嘴Sprue Bushing产品编号Part No三板模延伸式唧嘴Extension Nozzle缩水Shrinkage Bushing版本Rev 水口板导套Runner Stripper PlateBushing 模胚Mold Base定位圈（法兰）Locating Ring 下模镶件Core Block管钉（定位销）Dowel Pin 上模镶件Cavity Block管状管钉Tubular Dowel 吊环Safety Hoist Ring小镶件Sub-Insert下模小镶件Core Sub-Insert日期印Dating Insert 上模小镶件Cavity Sub-Insert行位 Slide喉塞 Plug行位镶件 Slide Insert压条 Gib 压紧块（铲机） Jaw 硬片（摩擦片） Wear Plate 水口铁 Runner Bar 上模水口铁 Upper Runner Bar 下模水口铁Lower Runner Bar 弹簧 Spring 水口勾针Sprue Puller Pin 顶针 Ejector Pin 撑头Support Pillar 直身锁 Side Lock顶针底板 Ejector Retainer Plate 斜度锁Interlock垫板Retainer Plate锁模板 Safety Bar垃圾钉Stop Pin'O'令（密封圈）O'Ring有托顶针 Shoulder Ejector Pin 隔水片 Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶 Lifter控制开关 Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA '板A'PlateB '板B'Plate方铁（垫铁） Spacer Block顶针板 Ejector PlateEjectionBushing针板导柱 Guided Ejection Leader Pin 唧嘴 Sprue Bushing三板模延伸式唧嘴 Extension NozzleBushing水口板导套 Runner Stripper Plate加速顶Accelerated Ejector扁顶Blade出模斜波 Draft手动滑块模具 Hand Slide-In TypeMold回针板 Backup合模 Shutoff空隙槽 Clearance SlotMold日期印Dating Insert三板模 3-Plat Mold环保印Recycling Insert分型面 Parting Line气顶Air Poppet Valve司筒 Ejector Sleeve截水口镶件 R unner Shut-Off Insert垫圈 Washer早回Early Ejector Return吊环 Safety Hoist Ring顶针板导套GuidedBushing定位圈（法兰）Locating Ring导柱及导套 Leader Pin Bushing管钉（定位销） Dowel Pin 水口拉钩 Spuer Puller管状管钉Tubular Dowel模框镶件 Pocket Insert成型热固性塑胶模具 Thermoset吸针 Sucker Pin 回针板 Retainer Plate顶出板 Knock -Out Plate电 动 安 全 开 关 Electrical-Safety Switch脱开 Cut Of Position预先决定 Preload缓冲器 Bumper衬垫 Cushion公差 Tolerance突然性动作 Slam销针 Dowel钩槽 Gib精磨 Finished通框 Through Window夹水纹Weld Line变形Warpage走水不平均FillingUneven走不齐Short Shot挂成品Part Hanging漏水 Water Leakage刮花（擦伤） Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力 Pressure倒圆Fillet粘后模 Sticking Core熔接线（夹水纹） Weldline粘水口 StickingSprue顶棍Ejector 雕刻Engrave顶白Stress Mark 出模角Draft粘前模Sticking Cav 分模面Parting Surface名称块表Title Block 擦位Shut-Off(S/0)版本标识Revision Level 导套Bushing材料清单Stock List 回针Return Pin斜导柱（斜边）Angle Pin 加硬HardenA板A'plate 唧嘴SprueB板B'plate 设计筒图Design Preliminary 倒扣Under-Cut 丝印Silkprint披峰Flash 不干胶Adhesive Sticker 缩水Sink Mark 导向针Guide Din氮化Nitride 公差Tolerance不规则四边形Trapezoid 线切割Wire-Cut缩水Shrinkage 电火花Edm连续的Consecutive 抛光Polishing蚀纹Texture Inserts探热针Thermocouple 指定吨位的注塑机Specific Press三打螺丝毫（限螺丝）Stripper 水嘴接头Water FittingsBolt螺纹Eyebolt Thread盖板Cover Plate回针Stop Pin齿轮Gear二级顶出针Sub-Leader Pin油唧Hydraulic Cylinder镶件Mold Insert司筒Ejector Sleeve锁定位Lock导柱Leader Pin楔子（铲鸡） Wedge冷料# Cold Slag高产量模量High Volume Running Mold线切割Wire E.D.M.剖面图Cross Section轮廓Contour模具结构Mold Construction螺纹孔Tapping Hole模芯Parting Core连接件Fittings局部视图Partial View斜针Angle Pin热流道Manifold接合Engage热嘴Hot Nozzle替换镶件Interchangeable Mold型腔数Cav No模号Mold No 胶料Material 尺寸Dimension重要尺寸Critical Dimension雕刻Engrave 托司EJ.GUIDE PIN。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
具
卡尺
caliper
千分尺
micrometer
直尺
ruler
高度尺
height gage
丝攻
screw tap
起子
screwdriver
拨牙器
jacker
扳手
wrench
风磨机
hand grinder
油石
oil stone
加
工
类
开料
cutting material
钻
drill (DR)
攻牙
tap
铰
冲孔
pierce
侧冲
cam pierce
切边
notch
切侧刃
notch french
折弯
bend
墩薄
coin
成形
form
侧成形
cam form
整形
restrike
围边
flange
打凸米
boss / dimple
打凸包
emboss
打字印
stamp
打沙拉孔
hourglass
面押
coin burr
抽孔
extrude hole
压边圈
binder
弹簧箱顶板
spring-box eject-plate
公
差
类
公差
tolerance
公差范围
tolerance range
上公差
upper tolerance
下公差
lower tolerance
公差+/- 0.05
plus minus 0.05
形位公差图
GD&T
平面度
flatness
Cast die
折弯模
Bending die
简易模
Prototypedie
围边模
Flange die
铆合模
Riveting die
拉伸模
Draw die
复合模
Compound die
快换模
Changeable die
工
序
类
料带
strip
料带图
strip layout
工序
process
冲导正孔
pilot pierce
(反面沉头￠0.00*0.00深)
(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)
(侧面沉头￠0.00*0.00深)
(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)
X:-M0.00钻穿,反面攻深0.00,有效牙0.00
X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)
X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00
X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)
X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00)
X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)
X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)
X:-￠0.00（合销孔,铰)
X:-￠0.00 (REAM FOR DOWEL)
X:-￠0.00（合销孔,割)单+0.00
X:-￠0.00 (W/C FOR DOWEL) S+0.00
X:-M0.00盲孔,反面攻深0.00,有效牙0.00
X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE)
X:-M0.00盲孔,正面攻深0.00，有效牙0.00
X:-M0.00 BLIND HL, TAPWORKDP0.00 TOP SIDE, THR DP0.00)
ream
铣
mill
车
lathe
电脑锣
NC mill
线切割
wire cutting(W/C)
磨
grind
刨
planer
电火花
EDM
镭射
laser cutting
倒角
chamfer
xx的精加工
finish XX
真空热处理
vacuum heat treatment
镀钛
TD coating
退磁
demagnetization
X:-￠0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING
X:-（漏油槽,反面CNC单+0.00,锣深0.00)
X:- (CN3;0.00, DP0.00)
X:-￠0.00（基准孔,铰)
X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)
X:-（避空孔,反面CNC单+0.00,锣深0.00)
X:-(POCKET, CNC MILL S+0.00 DP0.00OPPSIDE)
拍平
flat
卷圆
curl
种类
中文名称
英文名称
中文名称
英文名称
工
序
类
旋转
rotate
铆接
rivet
产品切边线
trim line
铆螺母
stake nut
切断
cutoff
接刀口
mismatch
料带带料处
carrier tab
毛刺方向
burr direction
压线
groove
下料
blanking
模
板
类
上托板
key slot
键
key
氮气弹簧
nitrogen spring
螺旋弹簧
coil spring
聚氨酯弹簧
urethane
导柱
guide post
导套
guide bushing
插针
pilot pin
插针套
pilot bushing
侧刃
french
传感器
sensor
销
dowel
螺丝
screw
拔牙
jackscrew
X:-￠0.00（合销孔,钻穿)
X:-￠0.00 (DR.THRU FOR DOWEL)
X:-￠0.00（一般孔,钻穿)
X:-￠0.00 (DR.THRU HL)
X:-￠0.00（穿丝孔,钻穿)
X:-￠0.00 (DR.THRU FOR WEDM S.H.)
X:-￠0.00（漏油孔,钻穿)按向视图加工
storage block
限位柱
stop block
起吊孔
handing hole
起吊环
eyebolt
靠块
heel
脱料拉杆
spool
模座导正块
thrust heel
种类
中文名称
英文名称
中文名称
英文名称
零
件
类
耐磨片
wear plate
垫片
shim
压块
keeper
初始管位
first start pin
键槽
X:-M0.00盲孔,正反面攻深0.00，有效牙0.00
X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)
X:-M0.00盲孔,侧面分中攻深0.00,组模自配
X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT)
烧焊
weld
4.1.2加工说明对照表：
加工说明Machining Note
注:有0.00的地方为数据填入处
外导套OUTER GUIDE BUISHING起吊杆HANDING PIN
实数铣通MILL THRU正反两面各铣TOP SIDE AND OPP SIDE MILL
X:-￠0.00（氮气弹弓过孔，锣穿）单+0.00
废料切断刀
slug breaker
成型凹模
forming die
整形公
restrike punch
导尺
rail
导尺顶杆
lifter bolt
导料板
rail plate
镶件/入子
insert
侧冲组件
cam
滑块
slide
滑块上油槽
oil groove
铲机
driver
码模槽
mounting slot
储运块
top plate
下托板
bottom plate
上垫脚
upper parallel
下垫脚
lower parallel
上模座
upper die set
下模座
lower die set
上垫板
punch backup
下垫板
lower backup
上夹板
punch holder
下夹板
die holder
上脱料板
X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00
X:-￠0.00 (C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)