螺丝攻牙钻孔径和滚丝径对照表上课讲义
螺纹攻牙钻孔径和滚造径对照表
*********本表依据二级牙制定
公制粗螺纹 规格 M1.0*0.25 M1.1*0.25 M1.2*0.25 M1.4*0.30 M1.6*0.35 M1.7*0.35 M1.8*0.35 M2.0*0.40 M2.2*0.45 M2.3*0.40 M2.5*0.45 M2.6*0.45 M3.0*0.50 M3.0*0.60 M3.5*0.60 M4.0*0.70 M4.0*0.75 M4.5*0.75 M5.0*0.80 M5.0*0.90 M6.0*1.00 M7.0*1.00 M8.0*1.25 M9.0*1.25 M10*1.50 M11*1.50 M12*1.75 M14*2.00 M16*2.00 M18*2.50 M20*2.50 M22*2.50 M24*3.00 M27*3.00 M30*3.50 标准径 0.75 0.85 0.95 1.10 1.25 1.35 1.45 1.60 1.75 1.90 2.10 2.20 2.50 2.40 2.90 3.30 3.25 3.80 4.20 4.10 5.00 6.00 6.80 7.80 8.50 9.50 10.30 12.00 14.00 15.50 17.50 19.50 21.00 24.00 26.50 二级牙钻孔径 最大 0.785 0.885 0.985 1.142 1.321 1.421 1.521 1.679 1.838 1.979 2.138 2.238 2.599 2.440 3.010 3.422 3.326 3.878 4.334 4.170 5.153 6.153 6.912 7.912 8.676 9.676 10.441 12.210 14.210 15.744 17.744 19.744 21.252 24.252 26.771 最小 0.
螺纹孔径和滚造径对照表
本表所推选钻头孔径,是针对攻牙加工时,能够很容易的了解钻头直径;而依据市售之标准钻头所选定的.在使用钻头的情况下,由于钻头的形状及尺寸,精度,被钻孔之材质等 钻孔径,若有不当之处,应实际状况适当的变更钻头直径,本表依据2级牙制订.
制 精 螺
纹
规格
公 制 细 螺 纹
标准径 11.00 11.50 12.50 13.00 13.50 14.00 14.50 15.00 15.50 16.00 16.00 16.50 17.00 18.00 18.50 19.00 20.00 20.50 21.00 22.00 22.50 23.00 23.00 23.50 24.00 24.50 25.00 25.50 26.00 26.00 26.50 27.00 27.00 28.00 28.50 29.00 30.00 M12×1.0 M12×0.5 M14×1.5 M14×1.0 M15×1.5 M15×1.0 M16×1.5 M16×1.0 M17×1.5 M17×1.0 M18×2.0 M18×1.5 M18×1.0 M20×2.0 M20×1.5 M20×1.0 M20×2.0 M22×1.5 M22×1.0 M24×2.0 M24×1.5 M24×1.0 M25×2.0 M25×1.5 M25×1.0 M26×1.5 M27×2.0 M27×1.5 M27×1.0 M28×2.0 M28×1.5 M28×1.0 M30×3.0 M30×2.0 M30×1.5 M30×1.0 M32×2.0 2级牙钻孔径 最大 最小 11.153 10.917 11.520 11.4 12.676 12.376 13.153 12.917 13.676 13.376 14.153 13.917 14.676 14.376 15.153 14.917 15.676 15.376 16.153 15.917 16.210 15.835 16.670 16.376 17.153 16.917 18.210 17.835 18.676 18.376 19.153 18.917 20.210 19.835 20.676 20.376 21.153 20.917 22.210 21.835 22.676 22.376 23.153 22.917 23.210 22.835 23.676 23.376 24.153 23.917 24.676 24.376 25.210 24.835 25.676 25.376 26.153 25.917 26.210 25.835 26.676 26.376 27.153 26.917 27.252 26.752 28.210 27.835 28.676 28.376 29.153 28.917 30.210 29.835
螺丝攻牙钻孔径和滚造径对照表
18.376 18.917 19.835 20.376 20.917 21.835 22.376 22.917 22.835 23.376 23.917 24.376 24.835 25.376 25.917 25.835 26.376 26.917 26.752 27.835 28.376 28.917 29.835 30.376 29.752 30.835 31.376 33.376 32.752 33.835 34.376
公制迫牙丝攻钻孔径 规格
M1.0*0.25 M1.1*0.25 M1.2*0.25 M1.4*0.30 M1.6*0.35 M1.7*0.35 M1.8*0.35 M2.0*0.40 M2.2*0.45 M2.3*0.40 M2.5*0.45 M2.6*0.45 M3.0*0.50 M3.5*0.60 M4.0*0.70 M5.0*0.80 M6.0*1.00 M7.0*1.00 M8.0*1.25 M10*1.50 M10*1.25 M12*1.75 M12*1.25 注:迫牙丝攻之钻孔径,在上表所列之 被加工材料之材质,硬度,形状,尺寸 多少会有所变动,因此于参考上表之
美 制 细 螺 纹 2级牙钻孔径 规格(UNF) 标准径 最大 最小 No.0-80(1.524) 1.25 1.305 1.182 No.1-72(1.854) 1.55 1.612 1.474 No.2-64(2.184) 1.85 1.912 1.756 No.3-58(2.515) 2.1 2.197 2.025 No.4-48(2.845) 2.4 2.458 2.271 No.5-44(3.175) 2.7 2.74 2.551 No.6-40(3.506) 2.9 3.022 2.82 No.8-36(4.166) 3.5 3.606 3.404 No.10-32(4.826) 4.1 4.165 3.963 No.12-28(5.846) 4.6 4.724 4.496 1/4-28 5.5 5.588 5.36 5/16-24 6.9 7.035 6.782 3/8-24 8.5 8.636 8.382 7/16-20 9.9 10.033 9.729 1/2-20 11.5 11.607 11.329 9/16-18 12.9 13.081 12.751 5/8-18 14.5 14.681 14.351 3/4-16 17.5 17.678 17.323 7/8-14 20.5 20.575 20.27 1-12 23.2 23.571 23.114 1-1/8-12 26.5 26.746 26.289 1-1/4-12 29.5 29.921 29.464 1-3/8-12 32.8 33.096 32.639 1-1/2-12 36 36.271 35.814
各种制式螺纹攻牙钻孔径和滚造径对照表
各种制式螺纹攻牙钻孔径和滚造径对照表，太全了金属加工2015-10-17 关注作者原文地址本表所推选钻头孔径，是针对攻牙加工时，能够很容易的了解钻头直径；而依据市售之标准钻头所选定的。
在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对于所钻孔的尺寸，精度有很大影响，所以使用本表之钻孔径，若有不当之处，应实际状况适当的变更钻头直径，本表依据2级牙制订。
公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917 M15×1.5 13.50 13.676 13.376 M15×1.0 14.00 14.153 13.917 M16×1.5 14.50 14.676 14.376 M16×1.0 15.00 15.153 14.917 M17×1.5 15.50 15.676 15.376 M17×1.0 16.00 16.153 15.917 M18×2.0 16.00 16.210 15.835 M18×1.5 16.50 16.670 16.376 M18×1.0 17.00 17.153 16.917 M20×2.0 18.00 18.210 17.835 M20×1.5 18.50 18.676 18.376 M20×1.0 19.00 19.153 18.917 M20×2.0 20.00 20.210 19.835 M22×1.5 20.50 20.676 20.376 M22×1.0 21.00 21.153 20.917 M24×2.0 22.00 22.210 21.835 M24×1.5 22.50 22.676 22.376 M24×1.0 23.00 23.153 22.917 M25×2.0 23.00 23.210 22.835 M25×1.5 23.50 23.676 23.376 M25×1.0 24.00 24.153 23.917 M26×1.5 24.50 24.676 24.376 M27×2.0 25.00 25.210 24.835 M27×1.5 25.50 25.676 25.376 M27×1.0 26.00 26.153 25.917 M28×2.0 26.00 26.210 25.835 M28×1.5 26.50 26.676 26.376 M28×1.0 27.00 27.153 26.917 M30×3.0 27.00 27.252 26.752 M30×2.0 28.00 28.210 27.835 M30×1.5 28.50 28.676 28.376 M30×1.0 29.00 29.153 28.917 M32×2.0 30.00 30.210 29.835 M32×1.5 30.50 30.676 30.376 M33×3.0 30.00 30.252 29.752 M33×2.0 31.00 31.210 30.835 M33×1.5 31.50 31.376 31.376 M35×1.5 33.50 33.676 33.376 M36×3.0 33.00 33.252 32.752 M36×2.0 34.00 34.210 33.835 M36×1.5 34.50 34.676 34.376 美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642NO.8-32(4.166) 3.40 3.530 3.302NO.10-24(4.826) 3.90 3.962 3.682NO.12-24(5.846) 4.50 4.597 4.3441/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3071 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339 PT1-1/2 -11 43.40 44 43.869 44.232 Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82公制螺纹规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425 美制粗螺纹规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76本表所推选钻头孔径,是针对攻牙加工时,能够很容易的了解钻头直径;而依据市售之标准钻头所选定的.在使用钻头的情况下,由于钻头的形状及尺寸,精度,被钻孔之材质等,对于所钻孔的尺寸,精度有很大影响,所以使用本表之钻孔径,若有不当之处,应实际状况适当的变更钻头直径,本表依据2级牙制订.公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106 M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917M15×1.5 13.50 13.676 13.376M15×1.0 14.00 14.153 13.917M16×1.5 14.50 14.676 14.376M16×1.0 15.00 15.153 14.917M17×1.5 15.50 15.676 15.376M17×1.0 16.00 16.153 15.917M18×2.0 16.00 16.210 15.835M18×1.5 16.50 16.670 16.376M18×1.0 17.00 17.153 16.917M20×2.0 18.00 18.210 17.835M20×1.5 18.50 18.676 18.376M20×1.0 19.00 19.153 18.917M20×2.0 20.00 20.210 19.835M22×1.5 20.50 20.676 20.376M22×1.0 21.00 21.153 20.917M24×2.0 22.00 22.210 21.835M24×1.5 22.50 22.676 22.376M24×1.0 23.00 23.153 22.917M25×2.0 23.00 23.210 22.835M25×1.5 23.50 23.676 23.376M25×1.0 24.00 24.153 23.917M26×1.5 24.50 24.676 24.376M27×2.0 25.00 25.210 24.835M27×1.5 25.50 25.676 25.376M27×1.0 26.00 26.153 25.917M28×2.0 26.00 26.210 25.835M28×1.5 26.50 26.676 26.376M28×1.0 27.00 27.153 26.917M30×3.0 27.00 27.252 26.752M30×2.0 28.00 28.210 27.835M30×1.5 28.50 28.676 28.376M32×2.0 30.00 30.210 29.835M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.376 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826) 3.90 3.962 3.682 NO.12-24(5.846) 4.50 4.597 4.344 1/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3077/8 -9 19.50 19.761 19.1771 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/8 -28 8.10 8.2 8.249 8.388PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339PT1-1/2 -11 43.40 44 43.869 44.232Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76来源：直观学机械推荐阅读1.钢价惨烈下跌风暴即将来临?不要以为和你没关系2.世界名刀大全，简直太漂亮了免责声明：本文系网络转载，版权归原作者所有。
螺丝攻牙钻孔底径对照表
3.17 3.62 4.56 5.45 6.45 7.31 9.18 9.31 11.04 11.31
ห้องสมุดไป่ตู้
3.2 3.65 4.6 5.5 6.5 7.38 9.25 9.38 11.12 11.38 3.69 4.64 5.55 6.55 7.44 9.32 9.44 11.21 11.44
No2 64UNF No3 - 56 No4 - 48 No5 - 44 No6 - 40 No8 - 36 No 10- 32 No 12 -28 1/4 28 5/16 3/8 24 7/16 20 1/2 -20
5.3 5.5 6.3 6.5 7 7.3 7.5 8 8.3 8.8 9 9.3 9.5 10 10.3 10.5 10.8
5.378 5.55 6.378 6.55 7.153 7.378 7.52 8.153 8.378 8.912 9.153 9.378 9.52 10.153 10.378 10.676 10.912
22.376 22.917 22.835 23.376 23.917 24.376 24.835 25.376 25.917 25.835 26.376 26.917 26.752 27.835 28.376 28.917 29.835 30.376 29.752 30.835 31.376 33.376 32.752 33.835 34.376
3.404 3.963 4.496 5.36 6.782 8.382 9.729 11.329 12.751 14.351 17.323 20.27 23.114 26.289 29.464 32.639 35.814
公制迫牙丝攻钻孔径
规格 精 度 等 级 G4-G6 G7-G8 G9
螺丝攻牙钻孔底径对照表
螺丝 攻牙 钻孔 径和 滚造 径对 照表
时间:201003-02 16:18来源: 未知 作 者:admin 点击: 143 次
本表所推选之钻头孔径，是针对攻牙加工时，能够很容易的了解钻孔直径；而依抿市售之标 准钻头所选定的，在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对 于所钻孔的尺寸.
M1.0*0.2
0.8 0.821 0.783
M1.1*0.2
0.9 0.921 0.883
M1.2*0.2
1 1.021 0.983
M1.4*0.2
1.2 1.221 1.421 1.383
M1.7*0.2
1.45
1.5 1.46
M1.8*0.2
1.6 1.621 1.583
M3.0*0.5 0 M3.0*0.6 0 M3.5*0.6 0 M4.0*0.7 0 M4.0*0.7 5 M4.5*0.7 5 M5.0*0.8 0 M5.0*0.9 0 M6.0*1.0 0 M7.0*1.0 0 M8.0*1.2 5 M9.0*1.2 5 M10*1.50 M11*1.50 M12*1.75 M14*2.00 M16*2.00 M18*2.50 M20*2.50 M22*2.50 M24*3.00 M27*3.00 M30*3.50
--
1/2 - 13
-
No 2 -
64UNF
No 3 - 56
4.9 4.96 -
5.72 -
7.24 -
8.74 8.81
10.2 10.3
11.27 11.82
螺丝攻牙孔径对照表
M12*1.0 M12*0.5 M14*1.5 M14*1.0 M15*1.5 M15*1.0 M16.1.5 M16*1.0 M17*1.5 M17*1.0 M18*2.0 M18*1.5 M18*1.0 M20*2.0 M20*1.5 M20*1.0 M22*2.0 M22*1.5 M22*1.0 M24*2.0 M24*1.5 M24*1.0 M25*2.0 M25*1.5 M25*1.0 M26*1.5 M27*2.0 M27*1.5 M27*1.0 M28*2.0 M28*1.5 M28*1.0 M30*3.0 M30*2.0 M30*1.5 M30*1.0 M32*2.0 M32*1.5 M33*1.0 M33*2.0 M33*1.5 M35*1.5 M36*3.0 M36*2.0 M36*1.5
10.917 11.400 12.376 12.917 13.376 13.917 14.376 14.917 15.376 15.917 15.835 16.976 16.917 17.835 18.376 18.917 19.835 20.376 20.917 21.835 22.376 22.917 22.835 23.376 23.917 24.376 24.835 25.376 25.917 25.835 26.376 26.917 26.752 27.835 28.376 28.917 29.835 30.376 29.752 30.835 31.376 33.376 32.752 33.835 34.376
1.25 1.55 1.85 2.10 2.40 2.70 2.90 3.50 4.10 4.60 5.50 6.90 8.50 9.90 11.50 12.90 14.50 17.50 20.50 23.20 26.50 29.50 32.80 36.00
标准螺丝攻牙钻孔径对照表【大全】
标准公制螺母攻牙要钻个小于螺纹大径的孔来攻牙。
这个孔的大小就是螺纹小径到螺纹中径。
如何确认孔径大小就要参照对照表啦,一起来看看吧！螺丝攻牙钻孔径对照表- 14 (3.175) 1- 11 30.20 30.472 30.111NO.6 - 32(3.505)2.80 2.895 2.6421-1/4 -11 38.80 39.133 38.771NO.8 - 32(4.166)3.40 3.530 3.3021-1/2 -11 44.70 45.026 44.664NO.10 -24(4.826)3.90 3.962 3.6832- 11 56.50 56.837 56.475NO.12 -24(5.486)4.50 4.597 4.3441/4 - 20 5.10 5.257 4.979英制管螺纹5/16 - 18 6.60 6.731 6.401 PF规格(新规格G) 标准径最大最小3/8 - 16 8.00 8.153 7.7987/16 - 14 9.40 9.550 9.1441/16 -286.70 6.843 6.561 1/2 - 13 10.90 11.023 10.592 1/8- 288.70 8.848 8.566 9/16 - 12 12.20 12.446 11.989 1/4- 1911.70 11.89 11.445 5/8 - 11 13.60 13.868 13.386 3/8- 1915.20 15.395 14.950 3/4 - 10 16.60 16.840 16.3071/2 - 14 19.00 19.172 18.6317/8- 919.60 19.761 19.177中之毋螺牙径1/16 -6.10 6.20 6.244 6.384281/8 -8.10 8.20 8.249 8.388281/4 -10.70 11.00 10.962 11.174193/8 -14.20 14.50 14.448 14.658191/2 -17.60 18.00 17.979 18.263143/4 -23.00 23.50 23.378 23.66314129.00 29.50 29.459 29.822- 111-1/4 -37.50 38.00 37.976 38.339111-1/2 -43.40 44.00 43.869 44.23211254.90 55.50 55.412 55.844- 11美制管螺纹针车用螺纹规格钻孔径规格标准径最大最小N P TN P SSM1/16 - 80 1.25 1.281 1.211使用绞刀时不用绞刀时SM5/64 - 64 1.55 1.593 1.5131/16 -275.946.15 6.35 SM3/32 - 56 1.90 1.936 1.841 1/8- 278.33 8.43 8.74 SM3/32 -100 2.10 2.156 2.081 1/4- 1810.72 11.13 11.13 SM1/8 - 32 2.30 2.393 2.233 3/8- 1814.27 14.27 14.68 SM1/8 - 40 2.50 2.551 2.421 1/2- 1417.48 17.86 18.26 SM1/8 - 44 2.50 2.605 2.485 3/4-1422.63 23.01 23.42 SM1/8 - 48 2.60 2.657 2.5471-11-1/228.58 28.98 29.36 SM9/64 - 32 2.70 2.79 2.6301-1/4 -11-1/237.31 37.69 38.10 SM9/64 - 40 2.90 2.948 2.8181-1/2-11-1/2 43.26 43.66 44.45SM11/64-323.50 3.584 3.4242-11-1/2 55.17 55.58 56.36SM11/64-403.70 3.742 3.612SM3/16 - 24 3.60 3.658 3.498英制螺纹SM3/16 - 28 3.80 3.844 3.684 规格钻孔径SM3/16 - 32 3.90 3.98 3.820 硬材软材SM3/16 - 40 4.05 4.138 4.008 W 1/8- 402.65 2.60 SM7/32 - 32 4.70 4.774 4.614 W 5/32- 323.25 3.20 SM15/64 -28 5.00 5.0554.875 W 3/16- 243.75 3.70 SM1/4 - 24 5.20 5.266 5.086 W 1/4- 205.10 5.00 SM1/4 - 28 5.40 5.452 5.272 W 5/16- 186.60 6.50 SM1/4 - 40 5.60 5.726 5.596 W 3/8- 168.00 7.90 SM9/32 - 20 5.70 5.824 5.634 W 7/16- 149.40 9.30 SM9/32 - 28 6.20 6.256 6.066 W 1/2- 1210.70 10.50 SM5/16 - 18 6.30 6.444 6.254 W 9/16- 1212.30 12.00 SM5/16 - 24 6.80 6.864 6.674W 5/813.70 13.50 SM5/16 - 28 6.90 7.05 6.860 - 11W 3/416.70 16.50 SM11/32 -28 7.70 7.843 7.653 - 10W 7/819.50 19.30 SM3/8 - 18 7.90 8.053 7.843 - 9W 122.40 22.00 SM3/8 - 28 8.50 8.637 8.447 - 825.00 24.00 SM7/16 - 16 9.30 9.44 9.220 W1-1/8- 728.30 28.00 SM7/16 - 28 10.10 10.224 10.034 W1-1/4- 7W 5/166.60 6.50 SM1/2 - 12 10.30 10.42 10.180 - 18W 3/88.00 7.90 SM1/2 - 20 11.30 11.41 11.190 - 16W 7/169.40 9.30 SM1/2 - 28 11.70 11.812 11.622 - 14W 1/210.70 10.50 SM9/16 - 20 12.90 13.018 12.778 - 12W 9/16 12.30 12.00- 12W 5/8- 1113.70 13.50W 3/4- 1016.70 16.50W 7/8- 919.50 19.30W 1- 822.40 22.00W1-1/8- 725.00 24.00W1-1/4- 728.30 28.00公制迫牙丝攻钻孔径美制迫牙丝攻钻孔径规格精度最大最小规格精度最大最小M1.0×0.25 G4 0.92 0.891-64UNCG5 1.76 1.68M1.2×0.25 G4 1.12 1.092-56G4 2.04 1.96M1.4×0.30 G4 1.3 1.263-48G4 2.35 2.250.80 -80UNC M6.0×1.0 G7 5.59 5.491-72G5 1.77 11.7M7.0×1.0 G7 6.59 6.492-64G4 2.06 1.98M8.0×1.25 G7 7.49 7.363-56G4 2.37 2.29M10×1.50 G7 9.34 9.224-48G5 2.68 2.59M10×1.25 G7 9.49 9.355-44G5 2.99 2.9M12×1.75 G8 11.23 11.096-40G5 3.29 3.19M12×1.25 G9 11.5 11.368-36G5 3.91 3.8110 -32 G6 4.53 4.44英制电器螺纹12 -28 G6 5.13 5.03 规格钻孔径1/4" -28 G7 6 5.91 2BA 4.0-4.2 5/16" -24 G7 7.53 7.42 3BA 3.4-3.6 3/8" -24 G7 9.1 8.99 4BA 3.0-3.2 7/16" -20 G8 10.62 10.48 5BA 2.7-2.8 1/2" -20 G8 12.2 12.06 6BA 2.4-2.5扩展资料：攻丝方法：攻丝是用一定的扭矩将丝锥旋入要钻的底孔中加工出内螺纹。
螺丝攻牙钻孔径和滚造径对照表
螺丝攻牙钻孔径和滚造径对照表
公制细螺纹
规格 M8.0×1.0 M8.0×0.75 M8.0×0.5 M9.0×1.0 M9.0×0.75 M10×1.25 M10×1.0 M10×0.75 M10×0.5 M11×1.0 M11×0.75 M12×1.5 M12×1.25 M12×1.0 M12×0.5 M14×1.5 M14×1.0 M15×1.5 M15×1.0 M16×1.5 M16×1.0 M17×1.5 标准径 7.00 7.30 7.50 8.00 8.30 8.80 9.00 9.30 9.50 10.00 10.30 10.50 10.80 11.00 11.50 12.50 13.00 13.50 14.00 14.50 15.00 15.50 2级牙钻孔径 最大 最小 7.153 6.917 7.378 7.520 8.153 8.378 8.912 9.153 9.378 9.520 10.153 10.378 10.676 10.912 11.153 11.520 12.676 13.153 13.676 14.153 14.676 15.153 15.676 7.188 7.400 7.917 8.188 8.647 8.917 9.188 9.400 9.917 10.188 10.376 10.647 10.917 11.400 12.376 12.917 13.376 13.917 14.376 14.917 15.376 规格（UNC） 1-3/8-12 1-1/2-12
美制细螺纹
2级牙钻孔径美制细螺纹Fra bibliotek2级牙钻孔径
螺丝攻牙钻孔径和滚造径对照表
公制细螺纹
2级牙钻孔径 规格 M28×1.0 M30×3.0 M30×2.0 M30×1.5 M30×1.0 M32×2.0 M32×1.5 M33×3.0 M33×2.0 M33×1.5 M35×1.5 M36×3.0 M36×2.0 M36×1.5 标准径 最大 27.00 27.00 28.00 28.50 29.00 30.00 30.50 30.00 31.00 31.50 33.50 33.00 34.00 34.50 27.153 27.252 28.210 28.676 29.153 30.210 30.676 30.252 31.210 31.676 33.676 33.252 34.210 34.676 最小 26.917 26.752 27.835 28.376 28.917 29.835 30.376 29.752 30.835 31.376 33.376 32.752 33.835 34.376 规格（UNC） 标准径 最大 最小
螺丝攻牙钻孔径和滚丝径对照表
螺丝攻牙钻孔径和滚丝径对照表公制粗螺纹美制粗螺纹规格标准径 2级牙钻孔径规格〔UNC〕标准径 2级牙钻孔径最大最小最大最小M1.0×0.25 0.75 0.785 0.729 NO.1-64(1.854) 1.55 1.582 1.425 M1.1×0.25 0.85 0.885 0.829 NO.2-56(2.184) 1.80 1.871 1.695 M1.2×0.25 0.95 0.9850.985 NO.3-48(2.515) 2.10 2.146 1.941M1.4×0.3 1.10 1.142 1.075 NO.4-40(2.845) 2.30 2.385 2.157 M1.6×0.35 1.25 1.321 1.221 NO.5-40(3.175) 2.60 2.697 2.487 M1.7×0.35 1.35 1.421 1.321 NO.6-32(3.505) 2.80 2.895 2.642 M1.8×0.35 1.45 1.521 1.421 NO8-32(4.166) 3.40 3.53 3.302M2.0×0.4 1.60 1.679 1.567 NO.10-24(4.826) 3.90 3.962 3.683 M2.2×0.45 1.75 1.838 1.713 NO.12-24(5.486) 4.50 4.597 4.344 M2.3×0.4 1.90 1.979 1.867 1/4-20 5.10 5.257 4.979M2.5×0.45 2.10 2.138 2.013 5/16-18 6.60 6.731 6.401M2.6×0.45 2.20 2.238 2.113 3/8-16 8.00 8.153 7.798M3.0×0.5 2.50 2.599 2.459 7/16-14 9.40 9.55 9.144M3.0×0.6 2.40 2.440 2.280 1/2-13 10.80 11.023 10.592M3.5×0.6 2.90 3.010 2.850 9/16-12 12.20 12.446 11.989M4.0×0.7 3.30 3.422 3.242 5/8-11 13.60 12.868 13.386M4.0×0.75 3.25 3.326 3.106 3/4-10 16.50 18.840 16.307M4.5×0.75 3.80 3.878 3.688 7/8-9 19.50 19.761 19.177M5.0×0.8 4.20 4.334 4.134 1 22.20 22.606 21.971M5.0×0.9 4.10 4.170 3.930 1-1/8-7 25.00 25.349 24.638M6.0×1.0 5.00 5.153 4.917 1-1/4-7 28.20 28.524 27.813M7.0×1.0 6.00 6.153 5.917 1-3/8-6 30.80 31.115 30.353M8.0×1.25 6.80 6.912 6.647 1-1/2-6 34.00 34.290 33.528M9.0×1.25 7.80 7.912 7.647 1-3/4-5 39.50 39.827 38.964M10×1.5 8.50 8.676 8.376 2-4-1/2 45.20 45.593 44.679M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.835M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 20.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211螺丝攻牙钻孔径和滚丝径对照表公制细螺纹美制细螺纹规格标准径 2级牙钻孔径规格〔UNC〕标准径 2级牙钻孔径最大最小最大最小M1.0×0.2 0.80 0.821 0.783 NO.0-80(1.524) 1.25 1.305 1.182M1.1×0.2 0.90 0.921 0.883 NO.1-72(1.854) 1.55 1.612 1.474M1.2×0.2 1.00 1.021 0.983 NO.2-64(2.184) 1.85 1.912 1.756M1.4×0.2 1.20 1.221 1.183 NO.3-56(2.515) 2.10 2.197 2.025M1.6×0.2 1.40 1.421 1.383 NO.4-48(2.845) 2.40 2.458 2.271M1.7×0.2 1.45 1.500 1.460 NO.5-44(3.175) 2.70 2.740 2.551M1.8×0.2 1.60 1.621 1.583 NO.6-40(3.505) 2.90 3.022 2.820 M2.0×0.25 1.75 1.785 1.729 NO.8-36(4.166) 3.50 3.606 3.404 M2.2×0.25 1.95 1.985 1.929 NO.10-32(4.826) 4.10 4.165 3.963 M2.3×0.25 2.05 2.061 2.001 NO.12-28(5.846) 4.60 4.724 4.496 M2.5×0.35 2.20 2.221 2.121 1/4-28 5.50 5.588 5.360M2.6×0.35 2.20 2.246 2.186 5/16-24 6.90 7.035 6.782M3.0×0.35 2.70 2.721 2.621 3/8-24 8.50 8.636 8.382M3.5×0.35 3.20 3.221 3.121 7/16-20 9.90 10.033 9.729M4.0×0.5 3.50 3.599 3.459 1/2-20 11.50 11.607 11.329M4.5×0.5 4.00 4.099 3.959 9/16-18 12.90 13.081 12.751M5.0×0.5 4.50 4.599 4.459 5/8-18 14.50 14.681 14.351M5.5×0.5 5.00 5.099 4.959 3/4-16 17.50 17.678 17.323M6.0×0.75 5.30 5.378 5.188 7/8-14 20.50 20.675 20.270M6.0×0.5 5.50 5.550 5.400 1-12 23.20 23.571 23.114M7.0×0.75 6.30 6.378 6.188 1-1/8-12 26.50 26.746 26.289M7.0×0.5 6.50 6.550 6.400 1-1/4-12 29.50 29.921 29.464M8.0×1.0 7.00 7.153 6.917 1-3/8-12 32.80 33.096 32.639M8.0×0.75 7.30 7.378 7.188 1-1/2-12 36.00 36.271 35.814M8.0×0.5 7.50 7.520 7.400M9.0×1.0 8.00 8.153 7.917M9.0×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188. .M12×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.400M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917M15×1.5 13.50 13.676 13.376M15×1.0 14.00 14.153 13.917M16×1.5 14.50 14.676 14.376M16×1.0 15.00 15.153 14.917M17×1.5 15.50 15.676 15.376M17×1.0 16.00 16.153 15.917M18×2.0 16.00 16.210 15.835M18×1.5 16.50 16.676 16.376M18×1.0 17.00 17.153 16.917M20×2.0 18.00 18.210 17.835M20×1.5 18.50 18.676 18.376M20×1.0 19.00 19.153 18.917M22×2.0 20.00 20.210 19.835M22×1.5 20.50 20.676 20.376M22×1.0 21.00 21.153 20.917M24×2.0 22.00 22.210 21.835M24×1.5 22.50 22.676 22.376M24×1.0 23.00 23.153 22.917M25×2.0 23.00 23.210 22.835M25×1.5 23.50 23.676 23.376M25×1.0 24.00 24.153 23.917M26×1.5 24.50 24.676 24.376M27×2.0 25.00 25.210 24.835M27×1.5 25.50 25.676 25.376M27×1.0 26.00 26.153 25.917M28×2.0 26.00 26.210 25.835M28×1.5 26.50 26.676 26.376M28×1.0 27.00 27.153 26.917M30×3.0 27.00 27.252 26.752M30×2.0 28.00 28.210 27.835M30×1.5 28.50 28.676 28.376M30×1.0 29.00 29.153 28.917. v .M32×2.0 30.00 30.210 29.835M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.676 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376螺丝攻牙钻孔径和滚丝径对照表公制挤压丝攻钻孔径美制挤压丝攻钻孔径规格精度等级规格〔UNC〕精度等级G4-G6 G7-G8 G9 G4-G6 G7-G8 G9M1.0×0.25 0.86 0.88 － NO.2-56UNC 1.94 －－M1.1×0.25 0.96 0.98 － NO.3-48 2.23 －－M1.2×0.25 1.06 1.08 － NO.4-40 2.50 －－M1.4×0.3 1.24 1.25 － NO.5-40 2.83 －－M1.6×0.35 1.41 1.43 － NO.6-32 3.07 －－M1.7×0.35 1.51 1.53 － NO.8-32 3.73 3.77 －M1.8×0.35 1.61 1.63 － NO.10-24 4.24 4.3 －M2.0×0.4 1.78 1.80 － NO.12-24 4.90 4.96 －M2.2×0.45 1.95 1.98 － 1/4-20 － 5.72 －M2.3×0.4 2.08 2.10 － 5/16-18 － 7.24 －M2.5×0.45 2.25 2.28 － 3/8-16 － 8.74 8.81M2.6×0.45 2.35 2.38 － 7/16-14 － 10.20 10.30 M3.0×0.5 2.73 2.75 － 1/2-13 － 11.27 11.82M3.5×0.6 3.17 3.20 － NO.2-64UNF 1.97 －－M4.0×0.7 3.62 3.65 3.69 NO.3-56 2.27 －－M5.0×0.8 4.56 4.60 4.64 NO.4-48 2.56 －－M6.0×1.0 5.45 5.50 5.55 NO.5-44 2.86 －－M7.0×1.0 6.45 6.50 6.55 NO.6-40 3.16 －－M8.0×1.25 7.31 7.38 7.44 NO.8-36 3.78 －－M10×1.5 9.18 9.25 9.32 NO.10-32 4.39 4.43 －M10×1.25 9.31 9.38 9.44 NO.12-28 4.99 5.04 －M12×1.75 11.04 11.12 11.21 1/4-28 5.85 5.90 －M12×1.25 11.31 11.38 11.44 5/16-24 7.36 7.41 － 3/8-24 － 9.00 －. .7/16-20 － 10.48 10.541/2-20 － 12.07 12.13美制特细螺纹英制电器螺纹规格标准径 2级牙钻孔径规格钻孔径最大最小NO.12-32 4.70 4.826 4.623 2BA 4.0-4.21/4 -32 5.60 5.690 5.486 3BA5/16 -32 7.10 7.264 7.087 4BA 3.0-3.23/8 -32 8.70 8.865 8.661 5BA 2.7-2.87/16 -28 10.20 10.338 10.135 6BA 2.4-2.51/2 -28 11.80 11.938 11.7099/16 -24 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028螺丝攻牙钻孔径和滚丝径对照表英制螺纹公制螺纹针车用螺纹规格(UNEF) 钻孔径规格滚丝径规格滚丝径硬材软材W 1/8 - 40 2.65 2.60 M3×0.5 2.63-2.60 SM1/8-40 2.735-2.688W 5/32 - 32 3.25 3.20 M3.0×0.6 2.56-2.53 SM1/8-44 2.769-2.722W 3/16 - 24 3.75 3.70 M3.5×0.6 3.06-3.03 SM9/64-40 3.128-3.083 W 1/4 - 20 5.10 5.00 M4.0×0.7 3.49-3.45 SM11/64-40 3.855-3.805 W 5/16 - 18 6.60 6.50 M4.0×0.75 3.45-3.41 SM3/16-32 4.205-4.155 W 3/8 - 16 8.00 7.90 M4.5×0.75 3.96-3.92 SM3/16-28 4.143-4.093 W 7/16 - 14 9.40 9.30 M5.0×0.8 4.43-4.38 SM7/32-32 5.003-4.955 W 1/2 - 12 10.70 10.50 M5.0×0.9 4.36-4.31 SM15/64-28 5.325-5.570 W 9/16 - 12 12.30 12.00 M6.0×1.0 5.30-5.25 SM1/4-40 5.890-5.735 W 5/8 - 11 13.70 13.50 M7.0×1.0 6.30-6.25 SM1/4-28 5.721-5.366 W 3/4 - 10 16.70 16.50 M8.0×1.0 7.28-7.23 SM9/32-28 6.508-6.648 W 7/8 - 9 19.50 19.30 M8.0×1.25 7.12-7.07 SM11/32-28 8.092-8.432 W1 - 8 22.40 22.00 SM3/8-28 8.880-8.015W 1-1/8 - 7 25.00 24.80 SM7/16-28 10.466-10.401W 1 - 1/4 - 7 28.30 28.00 SM7/16-16 10.037-9.967SM1/2-20 11.819-11.749. v .SM9/26-20 13.400-13.425英制管螺纹英制管螺纹美制管螺纹规格标准径钻孔径规格标准径有交牙部之长度〔最小〕中之毋螺牙内径标准长度〔最小〕中之毋螺牙内径规格钻孔径最大最小使用绞刀时不用绞刀时 NPT NPS使用绞刀时不用绞刀时PS 1/16 - 28 6.50 6.632 6.490 PT 1/16 - 28 6.10 6.20 6.244 6.384 1/16 - 27 6.10 6.25 6.35PS 1/8 - 28 8.50 8.637 8.495 PT 1/8 - 28 8.10 8.20 8.249 8.388 1/8 - 278.33 8.43 8.74PS 1/4 - 19 11.40 11.549 11.341 PT 1/4 - 19 10.70 11.00 10.962 11.174 1/4 - 18 10.72 11.13 11.13PS 3/8 - 19 15.00 15.054 14.846 PT 3/8 - 19 14.20 14.50 14.448 14.658 3/8 - 18 14.27 14.27 14.68PS 1/2 - 14 18.50 18.773 18.489 PT 1/2 - 14 17.60 18.00 17.979 18.263 1/2 - 14 17.48 17.86 18.26PS 3/4 -14 24.00 24.259 23.975 PT 3/4 - 14 23.00 23.50 23.378 23.663 3/4 - 14 22.63 23.01 23.42PS 1 - 11 30.20 30.471 30.111 PT 1- 11 29.00 29.50 29.459 29.822 1 - 11-1/2 28.58 28.98 29.36PS 1-1/4 - 11 38.80 39.132 38.772 PT 1-1/4 - 11 37.50 38.00 37.976 38.339 1-1/4-11-1/2 37.31 37.69 38.10PS 1-1/2 - 11 44.80 45.025 44.665 PT 1-1/2 - 11 43.40 44.00 43.869 44.232 1-1/2-11-1/2 43.66 44.04 44.45PS 2 - 11 56.50 56.836 56.476 PT 2 - 11 54.90 55.50 55.412 55.844 2 - 11 - 1/2 55.58 55.96 56.36。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
精品文档 精品文档 螺丝攻牙钻孔径和滚丝径对照表 公制粗螺纹 美制粗螺纹 规格 标准径 2级牙钻孔径 规格（UNC） 标准径 2级牙钻孔径 最大 最小 最大 最小 M1.0×0.25 0.75 0.785 0.729 NO.1-64(1.854) 1.55 1.582 1.425 M1.1×0.25 0.85 0.885 0.829 NO.2-56(2.184) 1.80 1.871 1.695 M1.2×0.25 0.95 0.985 0.985 NO.3-48(2.515) 2.10 2.146 1.941 M1.4×0.3 1.10 1.142 1.075 NO.4-40(2.845) 2.30 2.385 2.157 M1.6×0.35 1.25 1.321 1.221 NO.5-40(3.175) 2.60 2.697 2.487 M1.7×0.35 1.35 1.421 1.321 NO.6-32(3.505) 2.80 2.895 2.642 M1.8×0.35 1.45 1.521 1.421 NO8-32(4.166) 3.40 3.53 3.302 M2.0×0.4 1.60 1.679 1.567 NO.10-24(4.826) 3.90 3.962 3.683 M2.2×0.45 1.75 1.838 1.713 NO.12-24(5.486) 4.50 4.597 4.344 M2.3×0.4 1.90 1.979 1.867 1/4-20 5.10 5.257 4.979 M2.5×0.45 2.10 2.138 2.013 5/16-18 6.60 6.731 6.401 M2.6×0.45 2.20 2.238 2.113 3/8-16 8.00 8.153 7.798 M3.0×0.5 2.50 2.599 2.459 7/16-14 9.40 9.55 9.144 M3.0×0.6 2.40 2.440 2.280 1/2-13 10.80 11.023 10.592 M3.5×0.6 2.90 3.010 2.850 9/16-12 12.20 12.446 11.989 M4.0×0.7 3.30 3.422 3.242 5/8-11 13.60 12.868 13.386 M4.0×0.75 3.25 3.326 3.106 3/4-10 16.50 18.840 16.307 精品文档 精品文档 M4.5×0.75 3.80 3.878 3.688 7/8-9 19.50 19.761 19.177 M5.0×0.8 4.20 4.334 4.134 1 22.20 22.606 21.971 M5.0×0.9 4.10 4.170 3.930 1-1/8-7 25.00 25.349 24.638 M6.0×1.0 5.00 5.153 4.917 1-1/4-7 28.20 28.524 27.813 M7.0×1.0 6.00 6.153 5.917 1-3/8-6 30.80 31.115 30.353 M8.0×1.25 6.80 6.912 6.647 1-1/2-6 34.00 34.290 33.528 M9.0×1.25 7.80 7.912 7.647 1-3/4-5 39.50 39.827 38.964 M10×1.5 8.50 8.676 8.376 2-4-1/2 45.20 45.593 44.679 M11×1.5 9.50 9.676 9.376 M12×1.75 10.30 10.441 10.106 M14×2.0 12.00 12.210 11.835 M16×2.0 14.00 14.210 13.835 M18×2.5 15.50 15.744 15.294 M20×2.5 17.50 17.744 17.294 M22×2.5 19.50 19.744 19.294 M24×3.0 21.00 21.252 20.752 M27×3.0 24.00 24.252 23.752 M30×3.5 26.50 26.771 26.211 签名档： 精品文档
精品文档 螺丝攻牙钻孔径和滚丝径对照表 公制细螺纹 美制细螺纹 规格 标准径 2级牙钻孔径 规格（UNC） 标准径 2级牙钻孔径 最大 最小 最大 最小 M1.0×0.2 0.80 0.821 0.783 NO.0-80(1.524) 1.25 1.305 1.182 M1.1×0.2 0.90 0.921 0.883 NO.1-72(1.854) 1.55 1.612 1.474 M1.2×0.2 1.00 1.021 0.983 NO.2-64(2.184) 1.85 1.912 1.756 M1.4×0.2 1.20 1.221 1.183 NO.3-56(2.515) 2.10 2.197 2.025 M1.6×0.2 1.40 1.421 1.383 NO.4-48(2.845) 2.40 2.458 2.271 M1.7×0.2 1.45 1.500 1.460 NO.5-44(3.175) 2.70 2.740 2.551 M1.8×0.2 1.60 1.621 1.583 NO.6-40(3.505) 2.90 3.022 2.820 M2.0×0.25 1.75 1.785 1.729 NO.8-36(4.166) 3.50 3.606 3.404 M2.2×0.25 1.95 1.985 1.929 NO.10-32(4.826) 4.10 4.165 3.963 M2.3×0.25 2.05 2.061 2.001 NO.12-28(5.846) 4.60 4.724 4.496 M2.5×0.35 2.20 2.221 2.121 1/4-28 5.50 5.588 5.360 M2.6×0.35 2.20 2.246 2.186 5/16-24 6.90 7.035 6.782 M3.0×0.35 2.70 2.721 2.621 3/8-24 8.50 8.636 8.382 M3.5×0.35 3.20 3.221 3.121 7/16-20 9.90 10.033 9.729 M4.0×0.5 3.50 3.599 3.459 1/2-20 11.50 11.607 11.329 M4.5×0.5 4.00 4.099 3.959 9/16-18 12.90 13.081 12.751 M5.0×0.5 4.50 4.599 4.459 5/8-18 14.50 14.681 14.351 精品文档 精品文档 M5.5×0.5 5.00 5.099 4.959 3/4-16 17.50 17.678 17.323 M6.0×0.75 5.30 5.378 5.188 7/8-14 20.50 20.675 20.270 M6.0×0.5 5.50 5.550 5.400 1-12 23.20 23.571 23.114 M7.0×0.75 6.30 6.378 6.188 1-1/8-12 26.50 26.746 26.289 M7.0×0.5 6.50 6.550 6.400 1-1/4-12 29.50 29.921 29.464 M8.0×1.0 7.00 7.153 6.917 1-3/8-12 32.80 33.096 32.639 M8.0×0.75 7.30 7.378 7.188 1-1/2-12 36.00 36.271 35.814 M8.0×0.5 7.50 7.520 7.400 M9.0×1.0 8.00 8.153 7.917 M9.0×0.75 8.30 8.378 8.188 M10×1.25 8.80 8.912 8.647 M10×1.0 9.00 9.153 8.917 M10×0.75 9.30 9.378 9.188 M10×0.5 9.50 9.520 9.400
螺丝攻牙钻孔径和滚丝径对照表 公制细螺纹 美制细螺纹
规格 标准径 2级牙钻孔径 规格（UNC） 标准径 2级牙钻孔径 最大 最小 最大 最小 M11×1.0 10.00 10.153 9.917 精品文档 精品文档 M11×0.75 10.30 10.378 10.188 M12×1.5 10.50 10.676 10.376 M12×1.25 10.80 10.912 10.647 M12×1.0 11.00 11.153 10.917 M12×0.5 11.50 11.520 11.400 M14×1.5 12.50 12.676 12.376 M14×1.0 13.00 13.153 12.917 M15×1.5 13.50 13.676 13.376 M15×1.0 14.00 14.153 13.917 M16×1.5 14.50 14.676 14.376 M16×1.0 15.00 15.153 14.917 M17×1.5 15.50 15.676 15.376 M17×1.0 16.00 16.153 15.917 M18×2.0 16.00 16.210 15.835 M18×1.5 16.50 16.676 16.376 M18×1.0 17.00 17.153 16.917 M20×2.0 18.00 18.210 17.835 M20×1.5 18.50 18.676 18.376 M20×1.0 19.00 19.153 18.917 M22×2.0 20.00 20.210 19.835 M22×1.5 20.50 20.676 20.376