钻井英语
钻井工程专用英语词汇
钻井工程专业英语词汇绪论：钻井drilling 钻井方法drilling method顿钻钻井cable drilling 旋转钻井Rotary drilling动力系统(Power System) 旋转系统(Rotating System)提升系统(Hoisting System) 循环系统(Circulating System)井控系统(Well Control System) 直井straight hole深井deep well 超深井super deep well钻井设计well design 钻井质量drilling quality第一章：岩石的物理机械性质physical-mechanical properties of rock岩石的弹性模量elastic modulus of rock岩石的泊松比rock Poisson’s ratio岩石的切变模量shear modulus of rock岩石的体积压缩系数coefficient of bulk compressibility mineral and rock岩石的抗拉伸强度tensile strength of rock岩石的常规抗压缩强度compressive strength of rock岩石的抗剪切强度shear strength of rock脆性岩石brittle rock 塑性岩石plastic rock岩石塑性系数coefficient of plasticity of rock地应力in situ stress 围压confining pressure有效应力effective stress 压持效应chip hold effect岩石的可钻性drill ability of rock 岩石的研磨性rock abrasiveness各种压力概念concept of pressure 静液压力hydrostatic pressure钻井液压力drilling fluid column pressure孔隙压力pore pressure (formation pressure)上覆岩层压力overburden pressure 颗粒压力grain to grain pressure压力梯度pressure gradient 压力监控pressure detection and control 异常压力及其形成abnormal pressure and it’s formation压力异常abnormal pressure 压实作用compaction欠压实imcompaction 不渗透围栅permeabillity barrier地层压力检测方法method of formation pressure detection地震资料法seismic data method 机械钻速法penetration rate methodd指数法d-exponent method dc 指数法dc-exponent method标准化钻速法normalized penetration rate页岩密度法shale density地层破裂压力formation fracture pressure地层破裂压力预报方法formation fracture pressure prediction漏失试验法leak-off test 胡伯特-威利斯法Hubbert and Willis approach 马修斯-凯利法method of Matthews and Kelly伊顿法method of Eaton 安德森法Anderson’s method艾克斯劳格法Exlog method 黄荣樽法Huang’s metho d第二章：钻具drilling tool 钻柱drill stem复合钻柱combination string 满眼钻具packed hole assembly钟摆钻具pendulum assembly 稳定器stabilizer钻柱弯曲buckling of drill string第三章：钻井液drilling fluids 水基钻井液water-base drilling fluids淡水钻井液fresh-water drilling fluids 低固相钻井液low solids fluids泡沫钻井液foam drilling fluids 滤失filtrationAPI滤失量API filtration 动滤失量dynamic filtration滤饼filter cake 含砂量sand content钻井液固相含量solids content in drilling fluids钻井液流变性drilling fluids rheology 漏斗粘度funnel viscosity触变性thixotropic behavior 静切力gel strength初切力initial gel strength 终切力10-minuto gel strength盐水侵salt water contamination 钙侵calcium contamination砂侵sand contamination 水侵water contamination气侵gas contamination 钻井液处理剂mud additives降失水剂filtrate or reduction agents 增粘剂thickening agent降粘剂thinning agents 加重剂weighting agents堵漏剂lost circulation materials 固相控制solid control钻屑cutting 砂sand 泥silt 胶体颗粒colloidal solids第四章：钻进drilling 钻进技术drilling technology钻进技术参数drilling parameters 钻压weight on bit悬重和钻重string suspending weight and drilling weight转速rpm-revolution per minute 排量rate of flow零轴向点zero axial stress point 中性点neutral point开钻spud in 完钻finishing drilling 送钻bit feed方余和方入kelly-up and kelly-in 进尺footage机械钻速penetration rate 鳖钻bit bouncing 跳钻bit jumping起下钻trips 喷射jet-bit drilling 射流jet flow冲击射流impact jet flow 射流等速核potential core of jet 漫流cross flow射流喷速jet velocity射流冲击力jet impact force射流水功率jet hydraulic-power 喷射距离jet length 清洗井底bottom-hole cleaning钻头压降bit pressure-drop 钻头水功率bit hydraulic horse-power喷嘴nozzle 临界井深和极限井深critical well depth and limited well depth钻井泵的工作状态the working regime of drilling pump钻井泵的最大排工作状态（额定工作功率工作状态）the maximum flow rate regime of the drilling pump(the rated power regime of the drilling pump)钻进过程的数学模型mathematical model for drilling procedure钻速方程equation for drilling rate 五点法钻速试验“five spot” drill-off test第五章：{井眼轨迹基本概念（重点掌握）1、轨迹基本参数：3个2、轨迹计算参数：7个，特别注意水平投影长度、水平位移和视平移概念的区别3、轨迹的图视法.二、轨迹测量及计算1、测斜方法及测斜仪器简介2、测斜计算（重点掌握）三、直井防斜技术1、井斜原因分析2、静力学防斜：满眼钟摆（重点掌握）3、动力学防斜（了解）4、垂直钻井技术（了解）扭方位计算（重点掌握）}井下动力钻井hole bottom power drilling涡轮钻井turbo-drilling 涡轮钻具turbo-drill定向井directional well 定向要素directional elements井斜角inclination 方位角azimuth井斜变化率rate of inclination change方位变化率rate of azimuth change井眼曲率hole curvature 垂深和测深vertical depth and measured水平投影长度hole deviation水平位移displacement or closure distance多底井multi-bore well 水平井horizontal well丛式井cluster well or multiple wells造斜deflecting or building angle增斜increasing hole angle or build-up hole angle降斜decreasing hole angle or build-off hole angle稳斜 maintain angle 井身垂直投影图vertical projection of borehole井身水平投影图horizontal projection of borehole正切法tangential method 平衡正切法balanced tangential method平均角法average angle method 曲率半径法radius of curvature method圆弧法arc method 最小曲率法minimum curvature method造斜率rate of over-all angle change井眼方位漂移walk of hole 装置角tool of rotation工具面角tool face azimuth 动力钻具反扭角reactive torque定向方位角tool face bearing or tool face setting磁偏角magnetic declination 随钻测量measurement while drill(MWD)单点测斜仪single shot instrument 多点测斜仪multi-shot instrument陀螺测斜仪gyroscopic instrument 定向orientation定向下钻orientation while going in hole第六章：地层井眼系统的压力平衡balance of formation-borehole system地层压力当量钻井液密度equivalent drilling fluid density钻井液当量循环密度equivalent circulating density波动压力（激动压力）surge pressure 抽汲压力swabbing pressure溢流overflow 井涌kick 井喷well blowout地下井喷underground blowout 井喷失控out of control for blowout压井killing well 关井closing well硬关井hard closing 软关井soft closing压井方法killing well method 工程师法（等待加重量法）engineer’s method 司钻法（二次循环法）driller’s method防喷设备和工具blowout prevention tools and equipments第七章：固井well cementing 套管程序casing program导管conductor表层套管surface casing技术套管intermediate casing strings生产套管production casing 套管柱casing string套管柱下部结构casing accessories 引鞋guiding shoe套管鞋casing shoe 套管扶正器centralizer套管的外载荷outside casing load 套管内压力burst套管外挤压力collapse pressure 套管轴向力axial load套管强度casing strength 套管抗挤强度collapse resistance套管抗拉强度tensile resistance 套管抗内压强度burst resistance下套管running casing 活动套管moving casing井口装置wellhead equipment 低密度水泥light weight connect水泥浆流动性mobility of slurry 水泥浆密度slurry density水泥浆滤失量slurry filtration 前置液ahead fluid尾随液tail fluid 注水泥方法cementing methods常规注水泥法typical primary cementing双级注水泥法two stage cementing 插入注水泥法inner pipe cementing 尾管固井drilling liner cementing 尾管悬挂器drilling liner hanger窜槽cement channeling 完井方法completion methods裸眼完井法open hole completion 射孔完井法perforation completion 先期裸眼完井法initial open hole completion后期裸眼完井法final open hole completion第八章：卡钻drill pipe sticking 砂桥卡钻sand bridging键槽卡钻key seating 压差卡钻differential sticking地层膨胀卡钻formation swelling sticking地层坍塌卡钻formation collapse sticking钻头泥包卡钻balling-up sticking 卡点sticking point。
石油钻井工程英语口语基础词汇,了解一下
石油钻井工程英语口语基础词汇，认识一下~导读：本文石油钻井工程英语口语基础词汇，认识一下 ~ ，仅供参照，假如感觉很不错，欢迎评论和分享。
钻井： drill定向斜井： directional drilling欠均衡钻井： under-balance drilling海上钻井： off-shore drilling陆地钻井： on-shore drilling钻头： drill bit刮刀钻头： drag bit牙轮钻头：rock bit (镶齿钻头insert bit,钢齿钻头steel toothed bit)金刚石钻头： diamond bit取心钻头： coring bit钻头浮阀： float valve钻头水眼： bit nozzle(or jet)钻头水眼刺 :bit nozzle washed out钻头规： bit caliper(bit gauge)钻头泥包： bit is balling钻头钝了，我建议此刻起钻：bit is dull. I suggest to POOH now钻铤： DC(drill collar )光钻铤 slick drill collar，螺旋钻铤 spiral drill collar钻杆： DP(drill pipe )方钻杆： kelly公扣： pin end母扣： box end内平式连结： IF(internal flash)正规式连结： REG(regular)贯眼式连结： FH(full hole) 加重钻杆heavy weight drill pipe短钻杆pop joint井下马达： downhole motor涡轮钻具： turbine震击器： drilling jar减震器： absorber下部钻具组合： BHA （bottom hole assembly）钻具扶正器： stabilizer （string stabilizer, near-bit stabilizer）钻机： drill rig钻井泥浆： drilling mud钻井液： drilling fluid钻井设施： drilling equipment油：oil原油： crude oil天然气： nature gas煤层气： coal-bed gas石油： petroleum中国石油（简称）： CNPC （ China NationalPetroleum Corporation）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油： oil production产油层 (目的层 )：reservoir( or pay zone)钻进： drilling调整钻井参数以获得理想的机械钻速：play the drilling parameters to get fast ROP起钻： POOH(pull out of hole)下钻： RIH(run in hole)下套管： run casing(or RIH with casing)短起下钻： wiper trip循环泥浆： circulate泥浆： reverse circulate半途循环泥浆： break circulation分段下钻： RIH in stages通井： control trip划眼： reaming倒划眼： back reaming接单根： make connection滑、割大绳： slip and cut drilling line by ton-mile养护设施： maintain the equipment维修设施 : repair (or fix) the equipment养护顶驱： service TDS养护冲管： lubricate wash pipe待工日费： standby rate今日零日费： there is no day rate today(zero day rate today)我能够为您做，但一定收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围以内，我要报告领导，一有信息会立刻告诉你It is out of my power and I have to report to my boss. I willlet you know as soon as I get news.大鼠洞： rat hole小鼠洞： mouse hole钻具错扣： the connections are crossed钻具粘扣： thread is galled丝扣坏了： the thread is damaged起钻错扣： alternate the connections新钻具或接头磨扣： break in the new tool joint新钻头磨合： break in the new bitPDC 钻头井底造型： shape the PDC bit跳钻： rough drilling( vibrated drilling, bit is bouncing)蹩钻： rough drilling（drilling torque is abnormally high）缩径： tight hole起钻遇卡： get overpull下钻遇阻： set weight部分漏失： partially lost circulation所有漏失： totally lost circulation盲钻： blind drilling堵水眼： bit jets are blocked掉水眼： bit jets are lost憋压： the pressure is built up卸压： release pressure试压： pressure test功能测试： function test两方单独检查： double check地质： geology地质专业人员： geologist物理： physics地球物理勘探：geo-physical exploration.测井： logging电测井作业： wireline logging operation 泥浆测井： mud logging井（副词“好”含意）：well拓展记忆：井眼： bore hole油气井： oil&gas well试井： well test井下： down-hole井下作业： down-hole operation。
钻井英语单词
1.钻杆Drill Pipe2.钻铤Drill Collar3.钻柱Drill String4.钻头Bit5.“喇叭口”短节bell nipple6.短节nipple7.接头connection8.上扣Make up9.卸扣Break out10.扩眼器Hole opener11.钻井液Drill fluid / Mud12, 组合下部钻具Make up bottom hole assembly (BHA).12.接力柱Pick up stands.13.套管Casing.14.投（陶特）测斜仪Drop TOTCO15.循环Circulate16.起钻Run in hole17.下钻Pull out of hole18.垫圈Gasket19.气动扳手Air spinning tong20.气动绞车Air winch21.甩立柱Lay down stands22.循环清洗井眼Circulate hole clean23.停止钻进Stop drilling24.钻进Drilling ahead25.换钻头Change bit26.下抗磨补心Run the wear bushing27.正规公扣Regular pin28.上扣扭矩Make-up torque29.下9”钻挺Run in 9” collars30.猫头Cathead31.接配合接头Connect crossover sub32.卸立柱Break out the stands33.鼠洞Mousehole34.转盘Rotary table35.大钳Tong36.气动扳手Air spanner37.刮泥器Pipe wiper38.提升短节Lift sub39.安全卡瓦Safety clamp40.套管鞋Casing shoe41.钻井设计书Drilling program42.升每分LPM43.泵压Pump pressure44.划眼Ream the hole45.钻速Penetration rate46.水眼Nozzle47.悬重Hook load48.加重钻杆High Weight Drilling Pipe (HWDP)49.扶正器Stabilizer50.挠性结头Flexible sub51. 缩径井段undergauged interval52.泵压升高The pump pressure has increased53.内径Inside diameters54.猫头Cat line55.操作刹把Operate the brake lever56.坐上卡瓦Set slips57.震动筛Shaker58.划眼Ream59.钻压是多少？What is the weight on bit(简称WOB)60.吊卡elevator61.卡瓦slips62.防碰天车crown saver63.压井和防喷管线kill and choke line64.换割刀change the cutters65.除砂器desander66.除泥器desilter67.除气器degasser68.关掉shut it off69.链钳chain tong70.固井cementing71.水泥塞cementing plug72.水泥头cementing head73.引鞋guide shoe74. 扳手wrench75.护航船chase boat76.锚anchor77.自升式压载preload78.半潜式压载ballast79.舱室tank80.吃水draft81.井架derrick82.主机main engine83.锚机anchor winches84.牙轮bit cutter85.反循环打捞篮reverse-circulation basket86.取芯coring87.阀valve88.井下安全阀sssv (subsurface safety valve)89.海底管线subsea pipeline90.真空泵vacuum pump91.节流阀choke valve92.井口wellhead93.井筒wellbore94.压缩机compresser95.上甲板upper deck96.压载水舱water ballasttank97.关断shut down98.储能器accumulator99.进气管线admission pipe100.空气包air chamber101.环形BOP annualBOP 102.老虎钳bell nipple103.井架derrick104.抛锚drop anchors105.锚机anchor Winches106.甲板deck107.打捞fishing108.牙轮bit cutter109.落物junk110.取芯coring111.刹车brake112.投球drop ball113.解卡freeing stuck pipe 114.返出岩屑return cuttings 115.上提pull up116.下放slack off117.。
钻井专业英语(超齐全)
DRILLING PROFESSONAL WORDSunit one -personnel and post1.Are you a driller? 2.Are you a technician of this crew? 3.What is this toolpusher 's name? 4.Is he a mud engineer? Yes. He is a senior engineer. 5.He is a directional engineer. 6.He is an assistant driller. He is not a driller. Who is the driller of this shift? 7.Mr. Leo is the driller of this shift. We are all roughnecks of this shift. 8.How many roughnecks and motormen are there in this shift? 9. Is the driller on the drillfloor? No .He is on the mud tank.10. When did he begin to work as a rig manager? How long have you worked as a toolpusher?STUDY STUDYSTUDY ．．．．．LEARNING ．．．．．．．．PRACTISE ．．．．．．．．11. How long have you worked as a mechanist?12. He is in charge of drilling operation.13. Where do the floormen work? The work on the drillfloor.14. What is the toolpushers job? He is in charge of the shift operation.15. What is the derrickman responsible for? Who is he responsible to?16. Derrickma is responsible for attaching or detaching the elevators, for clearing, oiling,greasing, inspecting and repairing the pulley blocks, etc. He is responsible to the toolpusher.17. Who is the toolpusher responsible to? He is responsible to the drilling supervisor.18. What is the drilling supervisor responsible for? He is responsible for all drilling operations.19. The man driving the earthmover is LEO.20. The man 0perating brake bar is our driller.21. There are two roughnecks helping the driller get everything read for running in hole.22. The man who operates a brake bar is a driller.23. Here comes our superintendent.unit two-drilling fluids1.How long have you worked as a mud boy? I have been working as a mud boy since takingpart in job.2.In the petroleum industry, what is mud? The fluid for cooling the bit is called mud.3.Who mixes the mud? Where is the mud mixed? The floormen mix it at the mud tanks.4.What is bentonite? Bentonite is a clay .It consists of calcium, magnesium and aluminum.5.How does the mud reach the bit? It passes through the hollow string.6.What method do you take to check the quantity of salt in the mud?7.How many tons of barite can be placed there?8.On the day there was some mud in the tank .How many water was there in that one? It isabout ten cubic meters.9.Will more salt water be needed? Yes. It needs 50 cubic meters more.10.Do you know how to keep this kind of mud material? Under no conditions should this kind ofmud material be put in the sun for too long. Otherwise its properties will go bad.11.Do you know how to use these mud materials? Before using these mud materials，we mustknow their properties.12.How long will it take you to clear the mud tank? This work takes up too much time to clearthe mud tank. It will take us about three hours.13.How often do you make an experiment with the mud properties? Every four hours.14.What is the name of the special fluid? This fluid is called mud.15.Who is the person in charge of the drilling fluid? This fluid is called mud.16.How do you check the mud from the bottom of the hole? First，waiting for the mud to travelfrom the bottom up through the annulus to the surface.17.Is the specific gravity of the drilling fluid programmed to be higher or lower than the specificgravity of the cuttings? Why? It must be higher so that it can hold the cuttings in suspension if the mud circulation stops.18.If for any reason the mud circulation stops, the cuttings will be held in suspension 。
常用钻井完井石油机械英语单词
常用钻井、完井石油机械英语单词2001. ESP 电潜泵2. packer 封隔器3. safety valve 安全阀4. RIH（run in hole）下钻5. POOH (pull out of hole) 起钻6. pin公扣7. Box母扣8. tubing 油管9. tubing hanger 油管挂10. casing 套管11.casing head 套管头12. bit钻头13.chirstmas tree采油树14. liner尾管15. plug堵塞器16.sliding sleeve 滑套17. coiled tubing 连续油管18.discharge valve 排出阀19.drum滚筒20.elevator吊卡21.inlet入口22.spanner 扳手23.screwdriver 螺丝刀24.safetyjoint安全接头25.tong 大钳26. BOP防喷器27. rope socket绳帽28. stem加重杆29. jar震击器30. knuckle joint万向节31. slip卡瓦32. impression tool铅印33. gauge cutter通径规34. swaging tool胀管器35. wireline grab钢丝捞矛36. top drive顶驱37. drill stem钻柱38.directional drilling 定向钻井39. daily report 日报40.drilling water 钻井水41.fresh water 淡水42.gas cut 气侵43.seawater line 海水管线44.flowing pressure 流压45.formation water 地层水46.overload 超载47.membrane pump 隔膜泵48.dog leg ratio 狗腿度49.contractor承包商50. blind pipe盲管51. isolation packer隔离封隔器52. sump packer沉砂封隔器53. workover修井54. recompletion再完井55. logging测井56. well test试井57.screw螺钉58.nozzle 喷嘴59.nut 螺帽60.rigless ESP 无修井机电泵系统61.feedthrough 穿越62.cable 电缆63.sleeve 套64. clockwise顺时针65. breakout tongs卸扣大钳66. backup tongs背钳67. degasser除砂器68. degasser除气器69. centrifugal pump离心泵70. trip tank计量罐71. mixing pump混合泵72. power tong动力大钳73. bushing补心74. ware bushing 抗磨补心75. mud pump泥浆泵76. piston活塞77. normal circulation正循环78. reverse circulation反循环79. circulating pressure循环压力80. hydrostatic pressure静水压力81. bottom hole pressure井底压力82. turbulent flow紊流83. GEL凝胶84.life boat 救生艇85. life jacket救生衣86.life buoy 救生圈87.weight on bit 钻压88.thread alternating 错扣89.threadmaking造扣90.thread slipping滑扣91.thread off脱扣92.standby待命93.barite 重晶石94.deck甲板95.fire mask 消防面罩96.left-hand左旋97.right-hand右旋98.hookload大钩负荷99.casing size套管尺寸100.ballast water 压舱水101.back pressure 回压102.thread dope 丝扣油103.surface casing表层套管104.stabilizer扶正器105.shock absorber 减震器106.kelly in 方入107.kellyup方余108. polyme聚合物109. test paper试纸110. pump pressure泵压111. flow rate流量112. laminar flow层流113. gas vent valve放气阀114. cable protector电缆护罩115. torque gauge扭矩表116. portable便携式的117. overlap重叠118. additives添加剂119. wear out磨损120. deform变形121. casing tongs套管大钳122. tubing tongs油管大钳123. kelly方钻杆125. cathead猫头126. dead line死绳127. acidizing酸化128. fracturing压裂129. completion完井130. fishing打捞131 gravel砾石132. HRWP高速水充填133. sandstone砂岩134. FRAC-PACK压裂充填135. TVD垂深136. MD斜深137. HPHT高温高压138. filter cake滤饼139. horizontal well水平井140. proppant支撑剂141. permeability渗透率142. wash pipe冲管143. sand bridge砂桥144 fish落鱼145. sand control防砂146. perforating射孔147. collapse垮塌nding nipple 坐落接头149.top no-go 顶部止动150.bottom no-go 底部止动151.HRWP高速水充填152.blind pipe 盲管153.wire wrapped screen 绕丝筛管154. sand height 砂高155.gravel 砾石156.ceramic陶粒157.slurry浆液158.linear flow 线形流159.radial flow 径向流160.erosion腐蚀161.rig up 提起162 viscosity.粘度163. porosity孔隙度164. GP砾石充填165. core岩心167. mesh目数168. foam泡沫169. fishing job打捞作业170. open hole裸眼171.scraper刮管器172.sump packer 沉砂封隔器173.tubingspool油管四通174.safety clamp安全卡瓦175.killwell压井176.kill manifold 压井管汇177.mule shoe 斜口引鞋178.wiper trip 通井179.pit泥浆池180.annular环空的181. diesel柴油182.stuffingbox盘根盒183.RKB转盘补心面184.psi 磅/平方英寸185.BHA井下钻具组D垂深187.MD斜深188.TCP 油管携带射孔189.crossover变扣190.crane吊车191.artificial lift 人工举升192.mechanicaljar机械震击器193.workover equipment修井设备194.nippledown拆下195. landing nipple坐落接头196.derrick井架197.jackup自升式钻井船198.cable protector 电缆护罩199.by-pass旁通200.casing coupling 套管接插。
石油钻井专业英语词汇
目录第一节钻井英语单词 (2)第二节井场用语，钻井常用短语及句子 (10)第三节钻井泥浆术语 (29)第四节常用安全术语 (31)第五节钻井设备英语 (33)第六节石油钻井英语情景会话 (40)附录一：平台人员、作业者及服务公司人员名称 (47)附录二：主要设备名称 (48)附录三：钻具、井口工具、打捞工具名称 (52)附录四：材料和工具名称 (53)附录五：常用缩写形式 (55)第一节钻井英语单词drilling crew 钻井队drill floor,rig floor,floor 钻台drawworks 绞车well-site, rig-site 井场rig manager 平台经理DC (drill collar) 钻铤drilling engineer 钻井工程师DP (drill pipe) 钻杆toolpusher 带班队长rotary table 转盘driller 司钻assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工liner 缸套motor fire man 司机（motorman）wellhead 井口circulation & solid system 循环固控系统machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令) cathead 猫头caravan 营房，大篷车tong 大钳elevator 吊卡well depth 井深slip 卡瓦makeup 上扣spud in 开钻breakout 卸扣ROP (rate of penetration),drilling speed, penetration rate 钻速trip 起下钻diesel-engine 柴油机loss circulation 井漏，循环漏失working uniform 工作服brake handle, brake bar 刹把water well condition 水井井况circulating tank, circulation tank 循环罐normal drilling 正常钻进reserve tank 储备罐parameter 参数trip tank 补给罐，尖底罐, 起下钻泥浆罐（起下钻计量罐）rotary speed 转盘转速（转速）shale shaker 振动筛pump pressure 泵压WOB (weight on bit) 钻压mesh 目,网孔;啮合,编织torque 扭矩screen cloth 筛布displacement 排量safety meeting 班前会pump stroke 泵冲shift exchange 交班、（倒班）mud pump 泥浆泵master 师傅,主人;征服,控制,精通in charge of 负全责,经营,照顾obtain 获得,得到according to 根据,依照normal 正常的,正规的,标准的introduce 介绍,传入,引进,提出progress 前进,行进,进展supervisor 监督location 井场,井位inspection 检查,考察,验收cellar 方井soild (control) system 固控系统waste pit 污水池、废水池Top Drive (Drilling System)顶(部)驱(动)钻井系统Project Department 项目部on duty 值班modify 整改、修改clinic 医务室electic al rig 电动钻机disconnect 拆开,分离,断开pipeline 管线order 指令,命令,顺序Company 公司,甲方Operator 业主,甲方Contractor 承包商,乙方pump house 泵房schedule 时间表,进度表size 尺寸,大小,尺码information 通知,信息,资料equipment 设备,装备,器材instruction 指令,指示,说明书SCR house 可控硅房replace 更换,替换,代替brake shoe 刹车块wear out 磨损safety 安全,保险,安全设备fax 传真guy 家伙,人standpipe 立管Campsite 营地crownblock 天车traveling block 游车dog-house 司钻休息室(钻工值班房)rat hole 大鼠洞mouse hole小鼠洞spudding inspection 开钻验收fill in 填充catwalk 狭窄的过道,高空走道;高台,天车台casing float collar 套管浮箍casing float valve 套管浮阀casing guide shoe 套管引鞋cement水泥,注水泥,结合剂,胶结剂plug 插头safety pin安全销glove手套quick-connector快速接头fire exting u isher灭火器stretcher担架First Aid紧急救护control board控制板weight mdicator指重表rotary torque indicator转盘扭矩表sling吊绳绳套deadline anchor死绳固定器brake system刹车系统drum滚筒safety line保险绳safety belt安全带hydraulic tong液压大钳slip卡瓦（和上面的重复）elevator吊卡（和上面的重复）bit breaker钻头盒chain tong链钳pipe tong管钳wrench板手pliers钳子、老虎钳scissor剪刀cable slot电缆槽vacuum degasser真空除气器butterfly valve蝶阀desilter除泥器desander除砂器degasser除气器mud gun泥浆枪agitator搅拌器leakage漏,泄漏,渗漏barite重晶石hopper漏斗piston活塞union由壬fuel tank燃油罐、高架罐remote control station远控房BOP stacks防喷器组kill line 压井管线choke line节流管线blowout preventer防喷器annular环空ram闸板low pressure低压fire blanket消防毯fire sand防火砂kitchen厨房storeroom储藏室bathroom卫生间(浴室)spudding date开钻日期spudding time 开钻时间string钻柱BHA（bottom hole assembly）井下钻具组合drilling jar随钻震击器drill box钻杆盒drilling program钻井程序、钻井指令drilling fluid钻井液mix up混和、调配、混淆mud material泥浆材料LCM（lost circulation material）堵漏材料、堵漏剂mud engineer泥浆工程师day tour白班night tour夜班drilling progress钻井进度routine inspection例行检查、日常cave in塌陷、塌下、井壁坍塌loss漏失kick井涌hole section井段casing setting depth套管坐封深度downhole problem（trouble）井下事故(井下复杂情况)undergauge 缩径tight hole井径缩小的井眼tight spot （井径）缩小点、缩小段footage钻井进尺formation地层、岩层、构造、组织make up a joint接单根（立柱）sticking 粘附、刺、卡钻sticking point卡点free point解卡点？？hook weight悬重unfreeze解卡back-off倒扣fishing 打捞sidetrack侧钻back reaming倒划眼soak oil泡油soak releasing 泡解卡剂slough off坍塌ream down划眼borehole operation井下作业deviational survey 井斜测量（测斜）make a trip 起下钻bouncing 跳跃的、大的、重的、跳钻bit bouncing 蹩跳bit balling 泥包钻头cutting 切削、切割、切屑、钻屑cutting sample 砂样mud logging 综合录井sandstone 砂岩Pooh(pull out of hole) 起钻RIH(run in hole)下钻junk 落物、金属屑、碎物junk sub 打捞（落物）接头scrape 擦、刮、擦痕、刮掉bit gauge 钻头规centralizer 扶正器hold pressure 蹩压day rate 日费standby rate 等待日费、待命费run casing下套管cementing operation固井作业drift casing套管通径？？clean thread洗扣geologist地质师、地质学家casing shoe套管鞋thread protector护丝casing tong套管钳wiper trip通井rigid centralizer刚性扶正器guide shoe引鞋float-collar浮箍accident事故、意外事件slurry水泥浆WOC（waiting-on--cement）候凝期nipple up安装（防喷器）primary cement job正注固井wireline log电测test pressure 试压International practice国际惯例choke manifold节流管汇lay down the string倒钻具nut螺母bolt螺栓、螺钉screw bolt螺栓、螺杆pipe ram半封闸板shut-down停工HWDP (heavy weight drill pipe) 加重钻杆calibrate 校正、定标judgment 判断bleed off lin e排砂(排放)管线commence 开始、着手isolate 隔离、隔绝、绝缘welding 焊接、压实、压结mud property 泥浆性能MW(mud weight) 泥浆比重mud density 泥浆密度funnel viscosity 漏斗粘度PV(plastic viscosity) 塑性粘度well control drill 井控演习、防喷演习increase 增大、增加、增大decrease 减少、降低；减少之量pressure gauge 压力表casing pressure 套(管)压(力)choke valve 节流阀coring operation 取心作业hole collapse井壁坍塌pressure surge 压力激动、压力涌动bump pressure 碰压cement head 水泥头re v erse circulation 反循环cement 水泥，注水泥；结合剂；粘紧，粘牢(重复)cement accelerator 水泥促凝剂cement hardener 水泥速凝剂, 水泥硬化剂cement head (注) 水泥头cementing jobs 注水泥作业cement job 固井作业cement squeeze 挤水泥bonus 奖金,红利completion job 完井作业hand pump 手摇泵,手压泵workshop 车间,工场nipple down 卸下nipple up 装上,接上,装配,安装(重复)ID (inside diameter) 内径torque-on-bit 钻头扭矩tubing bonnet 油管头tubing hanger 油管悬挂器, 油管挂tubing joint 油管接箍landing head (悬挂油管用)油管头,(油管)联顶头landing joint 联顶节[下套管或油管联顶时用] TBG (tubing) 油管spacer fluid 封隔液mud logging unit 综合录井仪cooperation 合作,协作sample sack 砂样袋engage 从事;啮合deadline anchor 死绳固定器,死绳锚(重复)drilling cost 钻井成本evaluate 评价,估价,求…的值in advance 预先overpressure 过压，超压力swab 抽汲eliminate 排除,消除pipe bouncing 钻具蹩跳drill string failure 断钻具twist-off 脱扣horizontal well 水平井vertical well 垂直井stainless steel 不锈钢anticline 背斜porosity 孔隙度potential 潜在的,可能的; 潜能,潜力densimeter 密度计communication 传达,信息,交流,通讯hook velocity 大钩速度verify 检验,查证,核实confirm 确定,批准,印证incredible 难以置信的round trip 起下钻resume normal drilling 恢复正常钻进goal 目的,目标understanding 理解,认识,谅解kill operation 压井作业wireline [electric] log 电测井GR 自然伽玛scrap iron 铁屑cotton yarn 棉纱paint 油漆cavern 大山洞,大岩洞,溶洞,穴fossil 化石;陈腐的,守旧的gas-bearing 含气的water-bearing 含水的DST(drill-stem test) 中途测试, 钻杆测试water loss 失水flow pressure 流动压力daily output 日产量target zone 目的层finishing drilling 完钻thermometer 温度计re v er s e circulation 反循环build up 建造，安装；压力增加，压力恢复build up a joint??Well Control & Drill Procedures井控措施及防喷演习程序LIST OF ABBREVIATIONS缩写表BHP - Bottom-Hole Pressure 井底压力BOP - Blow out Preventer 防喷器（重复）CDPP - Circulating drill pipe pressure 循环钻杆压力CP - Casing pressure 套管压力（重复）CSG – Casing 套管（重复）DC - Drill collar 钻铤DP - Drill pipe 钻杆ECD - Equivalent circulating density 当量循环密度EMW - Equivalent Mud Weight 当量泥浆比重FCP - Final Circulating Pressure 最终循环压力Gm – Mud weight 泥浆比重HPHT - High pressure high temperature高压高温HWDP - Heavy Weight Drill Pipe加重钻杆（重复）ICP - Initial Circulating Pressure初始循环压力LOT - Leak-Off Test地漏测试MAASP - Maximum Allowable Annular Surface Pressure最大容许环空表面压力MD - Measured depth测量深度MEMW - Maximum equivalent mud weight最大当量泥浆比重Ps - Static pressure静压力Q - Flow rate 流量ROP - Rate of penetration机械钻速SICP - Shut-in Casing Pressure关井套压SIDPP - Shut-in Drill Pipe Pressure关井钻杆压力TVD - Total vertical depth垂直总深kill and choke lines 压井和节流管线kill fuild 压井液killing well 压井kill job 压井作业kill line压井管线kill rate 压井排量kill string 压井管柱kill-weight-fluid 加重压井液，高比压井液operating skill 操作技巧view point 观点engage in 从事，啮合primary control 首要控制，一次井控secondry control 二等控制，二次井控tertiary control第三位控制，三次井控safety margin 安全系数circulate out循环带出wildcat 探井pressure surge 压力波动，压力骤增（重复）Kick Control Sheet 井涌控制表circulating bottoms up循环井底至井口的泥浆行程active mud system在用泥浆系统fill the hole 灌满井眼human failure 人为事故differential pressure压差additive 添加剂obstruction阻塞，阻挡evidence 迹象，证明lower Kelly cock 方钻杆下旋塞upper Kelly cock 方钻杆上旋塞stripping 强行起下钻potential 潜在的，可能的；势，位shut-in procedures 关井程序，关井步骤soft shut-in procedures 软关井程序with a careful eye on留心saver sub 保护接头pipehandler 管子操作装置Driller’s Method 司钻法water-based system 水基体系implement 执行overcome 克服Daily Drilling Report 钻井日报表up-to-date 现代化的，最新（式）的，当今的chilksan line活动弯头管线H2S ( hydrogen sulfide) 硫化氢Muster point (Muster board) 紧急集合点（紧急集合点标识牌）Wind sock 风向标SCBA (self-contained breathing apparatus) 呼吸器Oxygen, acetylene 氧气，乙炔Alarm 警报Ambulance 救护车Emergency team 应急小组Fire pump, Fire drill, Fire hose, ax, rope 消防泵，消防演习，消防水龙带,消防斧，消防绳JSA (job safety analysis)工作中安全因素分析HSE (health, safety and environment) 健康，安全，环保Escaping route 逃生路线Inflammables 易燃物品Work Permit (Permit to Work) 工作许可（证）Safety meeting for running casing, liner, electric log 下套管，尾管，电测安全会PPE (personal protection equipment) 劳保用品Special operation 特殊作业Vehicle inspection 车辆检查Housekeeping 打扫卫生Crane 吊车MSDS（material safety data sheet）泥浆药品安全使用手册first aid box 急救箱Helmet安全帽Safety glasses 护目Fall arrester 防坠器VIS (viscosity) 粘度PV (plastic viscosity) 塑性粘度（重复）YP (yield point) 屈服粘度(流动点) Gels (gel strength) 静切力(胶凝强度)low viscosity低粘high viscosity (hi-vis)高粘lightweight low-viscosity mud低比重低粘泥浆water tank水罐caustic soda 烧碱dangerous 危险sand trap 沉沙罐、锥形罐trip tank 计量罐pill tank加药罐waste pit 排沙池fluid loss 失水第二节井场用语，钻井常用短语及句子钻井（Drilling）1、Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业。
石油钻井英语缩写及词汇
石油钻井英语缩写及词汇DC: drill collar钻铤DP: drill pipe钻杆HWDP: heavy weight drill pipe加重钻杆X/O: crossover转换接头CSG: casing 套管WOC: wait on cementing侯凝POOH: put out of hole起钻（trip out）短起：short tripRIH: run in hole下钻（trip in）R/U: rig up组装N/U: nipple up组装L/D: lay down甩钻具DD：directional driller：定向司钻（斯伦贝谢的员工）w/: withBOP: blowout preventer防喷器、封井器BHA: bottom hole assembly井底钻具OD: outside diameter外径ID: inside diameter内径IF: internal flush内平FH: full hole贯眼EU: external upset外加厚IU: internal upset内加厚WBM: water base mud水基泥浆OBM: oil base mud油基泥浆TIW: Texas Iron Works全开安全阀MW: mud weight泥浆密度SPP: standpipe pressure立管压力MWD: measure while drilling随钻测量CCL: casing collar log套管接箍测井GR: gamma ray伽马（测井）HTHP: high temperature & high pressure高温高压RPM: round per minute转速SPM: stroke per minute泥浆泵TD: total depth总井深MD: measured depth斜深TVD: true vertical depth垂深PPG: pound per gallonRKB: rotary kelly bushing方钻杆补心GL: ground level地表LCM: loss circulation materials堵漏剂P/U: pick up上提WOB: weight on bit钻压VISC: viscosity泥浆粘度N/D: nipple down拆卸R/D: rig down拆卸SX: sacks袋、包BBL: barrel桶B/U: bottom up循环一周M/U: make up组装LB: poundPSI: pound per square inchESD: emergency shutdown紧急关停装置ROP: rate of penetration进尺速度（机械钻速）ESP：emergency response plan应急响应预案Isolation valve高低压闸门Swab 凡尔提（泥浆泵配件）Hub方卡瓦Bail 吊环Air hoist气葫芦Chain hoist手拉葫芦、倒链V-door (pipe ramp) 斜坡Flowline泥浆天槽Gas buster / poor boy液气分离器Slug pit配浆罐（配药罐）Trip nipple旋转头喇叭口Rotating head旋转头Chickson 活动弯头Trailer/container/cabin/quarter room住井房/生活区Trash pump排污泵Flare pit放喷池/点火池/防火墙pup joint：短节重晶石：bariteWear bushing：防磨套膨润土：gelCasing tally：套管数据Float shoe：浮鞋Float collar：浮匝Protector：护丝WDC：wait on cement：候凝Measure out of hole：校对井深surface casing：表层套管intermediate casing：技术套管production casing：生产套管方瓦：hub卡瓦：slip碳酸钙：calcium carbonate环形防喷器：annular 半封：pipe ram全封：blind ram Drift ：通径（vt）Gauge ring：通径规Resistivity：电阻套压：casing pressure油（管）压：tubing pressure XJH：须家河地层KOP：kick-off point：造斜点。
石油专业英语常用
石油专业英语常用The Standardization Office was revised on the afternoon of December 13, 2020石油专业英语（常用）油井（oilwell）指任何钻透地球表面（Earth'ssurface）的钻孔（boring），目的是发现（find）或生产（produce）石油（petroleum/oil/hydrocarbons）。
专门生产天然气的叫气井（gaswell）。
油井一般经历五个阶段：计划（planning）、钻井（drilling）、完井（completion）、生产（production）与报废（abandonment）。
首先用钻机（drillingrig）通过钻具（drillstring）上的钻头（drillbit）在地上钻出毫米的孔（hole），然后在钻孔（borehole）中下钢制油管（steeltubing）与套管（casing）。
套管与钻孔之间还可能需要用水泥（cement）来固定。
套管为井孔（wellbore）提供结构上的整体性（structuralintegrity），同时隔离（isolate）危险的高压区（highpressurezone）。
随着井深加大，钻头和套管尺寸会变小。
现在的油井通常都有2-5个逐渐变小的井口尺寸。
钻头通过与之连接的钻铤（drillcollar）来钻进岩层。
钻井液（drillingfluid/mud）通过钻杆（drillpipe）内部泵入钻头，作用包括冷却（cooling）钻头、提升钻屑（drillcuttings）、避免井壁（wellborewall）不稳定以及避免岩层液体由于压力进入井眼。
使用过的钻井液用振动筛（shaker）去掉钻屑后返回泥浆池（pit）循环利用。
通过在地面的顶部驱动装置（topdrive/kellydrive）增加额外的10米长的钻杆（joints）来增加钻井深度。
石油英语词汇
油田专用单词钻井（Drilling）专用词组Choke valve 阻风门Power plant 发电机组Hoisting floor 起重设备Lubrication 润滑油Safety valve 安全阀Mud pump 抽泥泵Discharge capacity 排放容量Centrifugal pump 离心泵Agitator 搅拌器Drill collar 钻铤Degasser 脱气装置Console 控制台Auxiliary 辅助的，补助的Kill line 压井线Kelly hole 放放钻杆洞，方钻杆鼠洞BOP 防喷器Chart recorder 图表记录器Gage=gauge 仪表（压力计）SCR 半导体可控整流器Wiring diagram 配线图表Stress relief grooved 压力释放槽Friction welded 摩擦Crossover subs 过渡接头Bit sub 钻头短接Float valve 浮阀Casing 套管Hole 井眼Near-bit 近钻头Stab 对扣，入扣，下管入井String stabilizer 稳绳器Corridor 走廊Casing elevator 套管吊卡Inspection reports 检查报告Single joint 单根Swivel 枢轴Sling 吊索Slip-type 卡瓦式Casing spider 套管卡盘Casing slip 套管卡瓦Lift ram 起落油缸Torque gauge 扭矩仪Load cell 测压元件Tubing 套管整形器Thread protector 螺纹护环Cementing unit 水泥灌浆机组Mixing hopper 混台漏斗Shaker assembly 振动筛Choke manifold 节流/阻流管汇Preventer 防喷器Make up tong 上口钳Break out tong 卸扣钳Top driver 顶驱Crown saver device 天车拯救装置Pipe rack 管架，管排Suction screen 真空筛浆机Trash pump 杂质泵DW 绞车Nominal 名义RT 转盘Solids control system 固控系统Dual standpipe 双立管Shaft 轴Drum 滚筒Auto-feeding unit 自动送钻装置WOB 钻压Parameter 参数Stepless speed adjustment 无级调速Clutch 离合器Safety caliper 安全钳Eddy brake 电磁涡流刹车Existing power rated 额定的砺磁功率Ex-proof 防爆Mast 井架General 概述Handle 安装Piston 活塞Stroke 冲程Territory 代理区域Commission 佣金，代理费Discharge 排量Liner 钢套C/W 包括，配有BOP 防喷器blowout prevention Master skid 主撬Structure 井座Wire rope 钢丝绳Drug feeding device 加药设施Spare 备用Load 负载Casing tong 套管钳Fitting 紧固件Scope of business 经营范围Set back 立根Span 跨距Racking platform 二层台During rising lowering 起放井架In virtue of 有利于Technical developing 技术开发Production mode 经营模式Shaft 轴With care of humanity 人性化的Dimension 尺寸Seamlessly 无级Transmission 传动Opening 开口Anti-fall device 防坠落装置Climbing assistant device 登梯助力器Oil cylinder 油缸Dog house on drill side 司钻偏房Output breaker 出路断路器In & out breaker 入出断路器Threaded bolts 螺栓Active tank 活性罐Charge 灌注Dampener 缓冲器Trip tank 补给罐Supplementary 增加项Driller’s console 司钻台Wire line spooler 钢丝绳倒绳机Wire line stringer 穿绳器Rat hole and mouse hole 大小鼠洞Cantilever 悬臂式Frame 架Braking disc 刹车盘Casing stabbing board 套管扶正台Stabilizer 稳定器Crane arm 吊臂Conform to 符合Sprocket teeth 链轮齿Rear mounted 后置Belts sheave 皮带轮Gauge 压力计Applicable 适用Centrifuge 离心分离机Humidity 湿度Level operated suction valve 液位制动吸入阀Linear shale shaker 线性振动筛Parallel running 并车运行Control cubicle 控制室MCC motor control cubicle 马达控制室Bus bar 母线PLC system 可编程逻辑控制系统Relay protection signals 继电保护信号Compressor 压缩机Ram 闸板Freight 运费Black start 冷启动Audio/video warning function for power off 断电声光报警系统Auxiliary 辅助Hopper 漏斗Processing 对。
石油专业英语(钻井)
石油专业英语（钻井）2008-08-02 21:02Drilling 钻井Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置.Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱（一个立柱就是三根钻杆接在一起）Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes.每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud.用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathead can’t give enoughtorque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了地质年代术语英汉对照2008-08-0221:04stratum 地层stratigraphic correlation 地层对比horizon 层位key bed 标志层barren bed 哑层lacuna 缺失hiatus 间断continuity 连续discontinuity 不连续conformity 整合unconformity 不整合angular unconformity 角度不整合para-unconformity 平行不整合geochronologic unit 地质年代单位eon 宙era 代period 纪epoch 世stage 期chron 时chronostratigraphic unit 年代地层单位eonothem 宇erathem 界system 系series 统stage 阶chronozone 时带biostratigraphic unit 生物地层单位biostratigraphic zone 生物地层带lithostratigraphic unit 岩石地层单位group 群formation 组member 段bed 层geochronologic scale 地质年代表Phaneozoic Eon(Eonothem)显生宙（宇）Cainozoic Era(Erathem) 新生代（界）Cenozoic Era(Erathem) 新生代（界）Quaternary Period(System) 第四纪（系）Holocene Epoch(Series) 全新世（统）Pleistocene Epoch(Series) 更新世（统）Tertiary Period(System) 第三纪（系）Neogene Period(System) 新第三纪（系）Pliocene Epoch(Series) 上新世（统）Miocene Epoch(Series) 中新世（统）Paleogene Period(System) 老第三纪（系）Oligocene Epoch(Series) 渐新世（统）Eocene Epoch(Series) 始新世（统）Paleocene Epoch(Series) 古新世（统）Mesozoic Era(Erathem) 中生代（界）Cretaceous Period(System) 白垩纪（系）Jurassic Period(System) 侏罗纪（系）triassic Period(System) 三叠纪（系）Palaeozoic Era(Erathem) 古生代（界）Permian Period(System) 二叠纪（系）Carboniferous Period(System) 石炭纪（系）Devonian Period(System) 泥盆纪（系）Silurian Period(System) 志留纪（系）Ordovician Period(System) 奥陶纪（系）Cambrian Period(System) 寒武纪（系）Cryptozoic Eon(Eonothem) 隐生宙（宇）Proterozoic Eon(Eonothem) 元古宙（宇）Neoproterozoic Era(Erathem) 新元古代（界）Sinian Period(System 震旦纪（系）Mesoproterozoic Era(Erathem) 中元古代（界）Palaeoproterozoic Era(Erathem) 古元古代（界）Archaean Eon(Eonothem) 太古宙（宇）Precambrian 前寒武纪石油钻井词汇Part One SLICK-LINE（钢丝作业）A. TOOLS rope socket 绳帽stem 加重杆roll stem 滚轮加重杆Tungsten stem 钨加重杆Lead stem 铅加重杆link jar 机械震击器tubular jar 管状震击器hydraulic jar 液压震击器spring jar 弹簧震击器knuckle joint 万向节swivel joint 旋转节wellhead adapter 井口变扣短节X-Over 变扣gauge cutter 通井规selective downshift tool 选择性滑套开关工具shiftting tool 移位工具blind box 盲锤L.I.B(lead impression block) 铅印swaging tool 胀管器spear 打捞矛prong grab 内捞矛center spear 外捞矛catcher 捕捉器wirefinder 钢丝探测器Go devil-F.B 平底撞棍Go devil-C.B 刀杆撞棍retriever 钢丝打捞器overshot 卡瓦打捞筒magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀alligator grab 鳄鱼爪sand bailer 捞沙筒pipe wrench 管钳tong chain 链钳spanner 扳手wireline clamp 钢丝夹hay pulley 地滑轮dump bailer 倾倒筒saw 锯子saw blade 锯条punch 冲子file 锉刀flat file 板锉,扁锉hammer 榔头pliers,vice 老虎钳wire cutter 断线钳forfex 剪刀tongs 大钳,钳子,管钳flat bit tongs 扁嘴钳screwdriver 改锥，螺丝刀wire stripper 剥皮钳,掳线钳wire-stripper pliers 剥线钳B. EQUIPMENTstuffing box 防喷盒lubricator upper section 上防喷管lubricator middle section 中防喷管lubricator lower section 下防喷管blowout preventer(BOP) 防喷器wellhead adapter 井口变扣短节Lincoln pump 林肯泵hand pump assy.for stuffing box 手压泵Fire extinguisher 灭火器hand tool box 手工具箱injector 注油器lifting cap BOP吊帽trolly 防喷管支撑架parasol 阳伞work vice 台钳chain block 链葫芦tie down chain 系紧链fixed pulley 定滑轮wobble pump 手摇泵wire line clamp 钢丝绳夹wire rope sling 绳套,钢丝吊绳winch 绞车winch barrel(drum) 绞车滚筒winch brake 绞车刹车winch drive shaft universal joint 绞车主动轴万向节winch drum shaft 绞车滚动轴winch line 吊装用绳套winch control panel 绞车控制面板winch truck 吊车C. OPERATIONSRTTS Operation for Shoot andPull RTTS完井服务RTTS Operation for CementSqueezing RTTS固井服务（挤水泥）Pulling Y Block 捞Y堵塞器Open SSD(Slide Side Door) 开生产滑套Close SSD(Slide Side Door) 关生产滑套Open Circulating SSD(Slide SideDoor) 开循环滑套Close Circulating SSD(Slide SideDoor) 关循环滑套Running Gauge Cutter 通井Clean up 地面完井放喷Open Drain Valve 砸泻油阀Pulling Test Plug 捞测试阀Running Jet Pump 投射流泵Pulling Jet Pump 捞射流泵Running Flow Regulator 投配水器Pulling Flow Regulator 捞配水器Fishing Drop Bar 捞点火棒Measuring Static Pressure 测静压Measuring Flowing Pressure 测流压Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带泵测压（射流泵）Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井Slick-line Operation for Completion 钢丝配合完井服务Slick-line Operation for acidizing 配合酸化钢丝作业Running Plug 投堵塞器Pulling Plug 捞堵塞器Run Impression Block 下铅印Running Prong 投平衡杆Sand Level detection 探沙面Run Sand Bailer 下捞砂桶Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全阀Running Go Devil 剪切钢丝Fishing Slickline 打捞钢丝Running Side Pocket Plug 投偏心堵塞器Pulling Side pocket Plug 捞偏心堵塞器Running Side Pocket Check Valve 投偏心阀Pulling Side Pocket Check Valve 捞偏心阀Sand Sampling 取砂样Stable Test 稳定试井Slickline Swab 抽吸Running Hanger 投悬挂器Pulling Hanger 捞悬挂器D. SPARE PARTSgrease injection control head 注脂头grease oil 注脂油grease oil tank 注脂油桶BOP pump c/w hose 手压泵及管线pressure test hose 试压管线lubricator bleed off manifold 防喷管针阀Martin Decker W-15 oil 马丁代克油Martin Decker WT indicator c/whose 指重器及管线picking for stuffing box 盘根bearing for the sheave for stuffingbox 轴承O-ring for lubricator 防喷管O环ram assembly for BOP 防喷管闸板总成O-ring for BOP BOP O环O-ring for wellhead adapter 井口变扣O环pin 销钉counter head 计数头cable for counter 计数器软轴bearing of hay pulley 地滑轮轴承Part two Pressure gaugeaccordance 一致,和谐accuracy 精确性,正确度acquisition 获得,获得物alignment 校直,调准append 附加,添加,悬挂apply 申请,应用available 可利用的,有用的battery 电池battery housing 电池筒battery tester 电池测量器baud rate 波特率bull nose 底堵cable 电缆,电线cable head 电缆头,电缆接头calculation 计算,考虑calibration 标度,刻度,校准calibration drift 漂移calibration parameter 标定参数cartesian 笛卡儿曲线certification 证书com port 串行通讯端口command 命令,掌握,支配communicate 沟通,交流,通讯compensate 偿还,补偿configuration 构造,结构,配置,外形configure 配置,设定consist 组成,构成control panel 控制面板convert 转换,使转变cross-over between gauge 压力计间变扣crystal 水晶,晶体current 电流damage 危险,损害data acquisition 获得数据decode 解码,译解delta time 累计时间deviate 偏离diagnostic 诊断diameter 直径digital 数字的directory 目录discussion 讨论display 显示器,显示,展示downhole tools 井下工具drain 消耗,耗尽dump data 回放数据durability 耐用性element 元素,元件,成分elevated temperature 高温encoder 译码器,编码器establish 建立,安置filter 过滤,筛选firmware 固件(软件硬件相结合)fixed rate 固定采样率flash 闪光,闪现frequency 频率,周率gauge 压力计graph 图表,曲线图grease for transducer 传感器用油housing 壳,壳体incorporate 合并,混合indicate 指出,显示individual 个别的,单独的install 安装,安置instrument 工具,器械,器具interface box 接口箱interface box 接口箱internal diagnostics 内部诊断lapse 失误,下降,过失linear plot 线性平面图log 日志maintenance 维护,保持manual 手册,指南manufacture 制造,加工merge 合并,并入,结合memory 存储器,内存module 模块observe 观察,观测offer 提供,企图parallel communication 并行通信period 周期,时期plug 堵,塞,插上,插栓port 端口,港口potential 潜在的,可能的presentation 陈述,表达presentation software 操作软件printer 打印机prior 优先的,在前的procedure 步骤,手续program 程序,节目prune 剪除,修剪,删除quality 质量,品质,性质quartz 石英range 范围,射程real time 实际时间record mode 记录模式reduce 减小,缩小,简化remote control 遥控,遥控操作remove 移动,开除,移交require 请求,要求resolution 分辨率response 回答,响应scale 刻度,天平,比例尺select 选择,挑选setup 机构,安装,装备,组织silicone oil 硅油sleep mode 休眠模式spanner for gauge 压力计专用扳手SRO(surface read-out) 地面直读surpass 超过,胜过talk mode 对话模式terminal 终点终端thread grease 丝扣油transducer 传感器,变频器,交换器transient 短暂的,瞬时的transmit 传输,传送,发射信号transport 传送器,运输机transportation box 压力计箱troubleshooting 发现并修理故障truncate 截取,修剪update 更新,校正,修正upload 上载variable rate 可变采样率various 不同的,多样的version 版本,译本volt 伏特voltage 电压wand 棒,棍,杖zoom 放大,缩放Part three PVT取样 air chamber plug extractor 空气室拉出手柄air chamber plug retaining ringextractor 梭管套旋出手柄air chamber tube assy 导流管air hose assy. 扫空管allen key 内六角autoclave vacuum nipple 抽真空头B/bench hose assy. 样瓶转样管back-up ring 背环compression spring 压缩弹簧filler funnel 漏斗flow regulator body 节流器flow regulator end cap 端帽flow regulator extractor 节流器拉出手柄fuse/110V 保险丝/110Vglycol 甘醇heating jacket for cylinder 样瓶加温器heating jacket for sampler 取样器加温器holder 装配手柄internal circlip 内簧卡internal circlip for cylinder 取样瓶卡环lock grubscrew 锁紧螺丝needle valve 针阀needle valve assy.extractor 针阀手柄needle valve body 针阀组件needle valve BUR former 针阀背环工具off ball 钢球off diskspring 弹簧片piston assy. 活塞总成piston removal 活塞移位工具piston ring 活塞环piston rod 活塞杆piston valve stem 梭阀杆pols-lock pin 锁定销钉pols-lock spring 锁定销钉弹簧posi lock pin depressing tool 锁定按压工具prime hand pump 注油器prime hand pump adaptor 注油器适配器prime port adaptor assy. 加压口适配器prime port nipple plug 加压口堵头prime port spanner 加压阀扳手prime pump assy. 手压泵适配器prime pump hose assy. 手压泵输出管push rod 推杆relief valve stem 调压阀杆retaining ring 制动环reversible circlip pliers 卡簧手钳safety solvent 清洗液sample analysis 试样分析,样品分析sample analyzer 试样分析器sample bailer 采样筒sample blob 井底取样器sample bomb 高压取样瓶,样品存储器sample bottle 取样瓶,采样瓶sample bottle valve adaptor 样瓶接头sample chamber 样品室sample cock 取样旋塞,取样拷克sample collection 取样,样品收集sample collection procedure 取样点,采样点sample collector 取样程序sample connection 试样收集器,采样员sample container 取样接头sample contamination 样瓶,样筒,样品容器sample cup 样品污染sample cylinder 样品杯sample cylinder tag 样瓶,样筒sample date 样瓶标签sample depth 取样日期sample frequency 采样深度sample hose 采样信号sample identification 取样井,采样井sample integrity 采样频率sample interval 样品管,采样胶皮管sample period 样品鉴定sample point 样品的真实性sample signal 取样间隔,取样速度sample well 取样周期sampler hose assy. 取样器软管总成setting screw 制动螺丝setting fork 导流叉管setting tool 空气定位销手柄setting tool 梭杆推进套shuttle mechanism assy. 触发机构tee ring seals T型密封环test gauge 压力表tool body clamp 取样器夹具tool dressing aids 更换'O'环工具torque wrench 扭矩扳手torque wrench adaptor 扭矩扳手接头torque wrench adaptor 扭矩扳手接头transfer bench assy. 转样器总成transfer lock sleeve 转样护帽transfer port adaptor 转样适配器transfer port plug 转样口堵头trigger mech. assy. 触发机构总成trigger spring 触发弹簧vacuum hand pump 真空泵vibra gauge 压力表Part four OthersAa directional engineer 定向井工程师a drilling engineer 钻井工程师a drilling supervisor 钻井监督a senior mud engineer 高级泥浆工程师a toolpusher 队长，技师abandoned drill 弃船演习accelevator 促凝剂acidity 酸性adapter 接头additive 添加剂/处理剂ahead water 先行水air chamber 空气包air hoist 气动绞车alarm 警报alkalinity 碱性泥浆比重amplitude log 声幅测井anchor 锚angle 角钢annular return velocity 泥浆返回流速annular space 环形空间annular velocity 环空流速apparent viscosity 视黏度asbestos 石棉assistant tug boat 护航船assistant driller 副钻aviation fuel 航空油Bback off 倒扣back pressure 回压back pressure valve 回压阀ball 球ball up 泥包barge engineer 平台工程师barite 重晶石bearing 轴承bearing angle 方位bed 床behind water 尾水bit 钻头bit bearing 钻头轴承bit breaker 钻头装卸器bit cost 钻头成本bit diameter 钻头直径bit gauge 钻头规bit life 钻头寿命bit nozzle 钻头水眼bit position 钻头位置bit sub 钻头接头bit time 钻头纯钻时间bit tooth 钻头牙齿bit torque 钻头扭矩bit type 钻头型号bit wear 钻头磨损blasting cap 雷管blow out 井喷blow out preventer 防喷器boiler 锅炉bolt 螺栓bolt,nut 螺丝,螺母bore hole 裸眼bore hole well 井壁boring 钻孔bottom hole 井底bottom fill 沉砂bottom hole pressure 井底压力bottom hole pressure 井底压力bottoms up 携带岩屑box 母扣brake 刹车break out 卸扣breech lock 泡栓build up 压力恢复bulk density 堆积密度;松装密度bulk tank 灰罐bumper sub 缓冲器buoyancy coefficient 浮力系数bushing 补芯butane 丁烷Ccable 电缆calcium remover 除钙剂calculating free piont 计算卡点深度calibration 刻度casing 套管,螺纹联接的兀接箍casing head 套管头casing spool 套管四通casing burst pressure 套管破裂压力casing elevator 套管吊卡casing monkey board 套管平台casing pressure 套压casing program 套管程序casing scraper 套管刮管器casing shoe 套管鞋casing sub 套管接头casing tong 套管大钳cathead 猫头cave in 坍塌cement 水泥cement basket 水泥伞cement bond log 固井质量检验cement flush 水泥冲洗cement slurry 水泥浆cement slurry for lead 先行水泥浆cementing 固井cementing line 固井管线cementing pump 固井泵center latch elevator 中开门吊卡centralizer 套管扶正器centrifugal pump 离心泵chain block 倒链change bit 换钻头chart 卡片check valve 单流阀chemical tank 化学药剂缸chemical treatment 化学处理chemicals 化学剂choke 油嘴choke line 阻流管汇choke manifold 试油树christmas tree 采油树circulating pressure 循环压力circulation 循环circulation rate 循环速度clamp 卡子clay contamination 粘土侵clock 时钟clog house 值班房cock 水龙头coefficient of friction 摩擦系数colloid 胶体completion 完井computer 计算机conductor 隔水导管cone 牙轮cone bit 牙轮钻头connector 联结器contamination of mud 泥浆污染contract 合同contractor 承包商control room 控制室conventional mud 普通泥浆cook 炊事员core 岩心core barrel 取芯筒core bit 取芯钻头core catcher 岩心爪core gun 取芯器core handling tools 取芯工具core recovery 取芯收获率coring 取芯coupling 联接扣cover 外壳crane operator 吊车司机critical velocity 临界速度cross 十字接头cross over,x-over(XO) 大小头，短节，变扣接头，旁通管crossover sub 配合接头crown block 天车cut off workline 割大绳cylinder 缸Ddaily production 日产量deadline 死绳deadline anchor 死绳固定器deck 甲板declination 偏差/方位角degas ser 除气器dehydration 失水densimeter 密度计depth 井深derrick 井架derrick man 架工desander 除砂器desilter 沉淀池, 滤水池detonator 炸药deviation survey 井斜测量diamond bit 金刚石钻头die collar 打捞卡瓦diesel oil 柴油different pressure sticking 压差卡钻directional well 定向井discharge of pump 泵排量dispersing agent 分散剂displace 替diver 潜水员doctor 医生drag 遇阻draw works 绞车drier(dring oven) 干燥计drift angle 倾角drift mandrel 通径规drifting 通径drill pipe 钻杆drill spool 钻井四通drill stem 钻柱drill strings 钻杆拄drill water 钻井水drill collar 钻铤drill floor 钻台drill floor 钻台driller 司钻drilling 钻进drilling technician 钻井技术员drilling assembly 钻具组合drilling break 进尺突然加快drilling cost 钻井成本drilling crew 钻井队员drilling engineer 钻井工程师drilling equipment 钻井装置,钻机drilling line 大绳drilling log 钻井记录drilling ration 钻速drilling recorder 钻井记录仪drilling rig 钻井船drilling troubles 井下事故drum shaft 滚筒轴DST(drill stem test) 延长DST测试dump valve 放泄阀duplex slush pump 双缸泥浆泵DV collar 分级注水泥短接DV port DV孔Eelbow 弯接头electric logging 电测electric submerged pump(ESP) 电潜泵electrician 电工elevator 吊卡elevator link 吊环emulsifier 乳化剂engine room 机舱erecting equipment 安装设备erecting tools 安装工具erode out 刺坏error 误差ethane 乙烷exploration 勘探extended well testing 延长测试external upset 外加厚Ffalse threading 造扣field maintenance 现场维护，现场保养fill line 灌泥浆管线filling up mud 灌泥浆filter cake 泥饼filter paper 滤纸filtration educing agent 降失水剂finger board 指梁fire drill 消防演习fishing 打捞fishing bumper sub 打捞缓冲器fishing jars 打捞震击器fishing job 打捞作业fishing neck 打捞颈fishing tools 打捞工具fishing up 打捞出落鱼flash welded tool joint 闪光焊接接头flashlight 手电float collar 浮箍float shoe 浮鞋floor man 钻工flow 放喷flow line 泥浆出口管线flow rate 流量flow line 出油管flow rate 流速flowing bean(nipple) 油嘴flowing pressure gradient 流压梯度fluid loss 失水量fluorescence 荧光反应formation 地层formation conductivities 地层电导率formation damage 破坏地层fracturing 压裂free pipe 未卡部分钻柱free point 自由点free standing mast 无绷绳轻便井架fresh water 淡水full hole(FH) 贯眼扣function 函数funnel viscometer 漏斗黏度计Ggamma ray 射线gamma ray log 自然测井gas reservoir 气层gas analysis 气体分析gas chromatography 气体色谱仪gas cut 气侵gas in mud 泥浆中气量gas oil ratio 油气比gas out 气侵gas showing 气体显示gasoline 汽油gauge 量规gear 牙轮gel 凝胶gel cement 胶质水泥gel mud 胶质泥浆gel strength 切力generator 发动机geothermal gradient 地温梯度goose neck 鹅颈管grade 级/等级grease 黄油guide shoe 引鞋gun perforation 射孔完井gypsum mud 石膏泥浆Hhammer 锤子hard ware 硬件heavy mud 重泥浆/加重泥浆heavy viscosity mud 高粘泥浆heavy weight drill pipe 加重钻杆heavy bodied 很稠的，粘滞的helicopter 直升飞机helicopter port 飞机平台helmet 安全帽hole opener 扩眼器hole size 井眼尺寸hole straightening 井眼校正/纠斜hook 大钩hook load 大钩负荷hook load off bottom 钻柱离底时大钩负荷hook position 大钩位置hopper 漏斗hose 软管/水龙带hull 船身hydraulic pressure 静水压力hydraulic oil 液压油hydrostatic pressure 静水压力IIF(internal flush) 内平扣indented bolt 齿纹螺栓indented chisel 齿状钻头，牙轮钻头indirect flushing 反循环洗井，反向冲洗induction electrical survey 感应电测井inertia brake 惯性刹车initial gel strength 出切inner barrel 内岩心筒inner string cementing 内管注水泥input 输入insert bit 镶齿钻头inside bop drill 安装回压凡尔演习intake profile 吸水剖面internal upset 内加厚internal-external upset 内外加厚interpreter 翻译invaded zone 侵入带invasion diameter 侵入直径inverse circulation 反洗井inverse well-flushing 反洗井isobutane 异丁烷isopentane 异戊烷Jjack knife mast 折叠式轻便井架jack up type drilling unit 自升式钻井船jars 震击器joint 单根junk basket 打捞蓝Kkelly 方钻杆kelly bushing 方钻杆补芯kelly cock 方钻杆考可kelly down 方入kelly down depth 方入深度kelly drive 方钻杆滚子补芯kelly spinner 方钻杆旋扣器kelly up 方余key seat 键槽key seating sticking 键槽卡钻kick 井涌kick control 控制井涌kill line 压井管汇killing a well 压井Llaminar flow 层流latching elevator 扣吊卡lay down 甩lay time 迟到时间leak 漏life raft 救生筏lifeboat 救生艇lift jacket 救生衣lifting sub 提升短接light weight mud 轻泥浆lignite 铁络盐lignite mud 铁络盐泥浆lime 石灰lime mud 石灰泥浆limit switch 相限开关line 管线line cleaning 管线清洗line test 管线试压liner 缸套,尾管liner hanger 尾管挂living quarters 居住区loading 装船logging cable 测井电缆logging program 测井程序logging tool 测井工具loosen 放松lost circulation 井漏lost circulation materials 堵漏剂lubricating oil 润滑油lubricator(assembly,system) 防喷管（装置，系统）Mmachine oil 机油main tug boat 主拖轮make up 上扣make up torque 上扣扭矩mast 钻机master bushing 转盘大补芯master valve 总闸门material man 材料员mean sea level 平均海平面mechanic 机械工mechanist 机械师methane 甲烷mica 云母milled teeth bit 铣齿钻头milling tool 铣具/磨鞋miring water 溶解水mixing pump 混合泵monkey board 二层台morning tour 白班motormen 机工mouse hole 鼠洞mud 泥浆mud agitator 泥浆搅拌器mud balance 泥浆密度计mud column 泥浆柱mud conditioning 泥浆处理/配泥浆mud conductivity 泥浆导电率mud density 泥浆密度mud ditch 泥浆槽mud flow meter 泥浆流量计mud gun 泥浆枪mud line 泥浆管线mud logging 泥浆录井mud pump 泥浆泵mud resistivity 泥浆电阻率mud retort 泥浆蒸馏水mud return line 泥浆返出管线mud tank 泥浆池mud temperature 泥浆温度mud testing 泥浆测试mud volume 泥浆量mud weight indicator 泥浆比重计mud tank 泥浆罐multiple completion 多层完井MW(mud weight) 泥浆重量,泥浆密度Nnail 钉子natural flow 自喷NDBOPS(nipple down blowout preventers) 卸下防喷器组NDT(nipple down tree) 拆卸井口装置，拆卸采油树near bit stabilizer 金钻头扶正器neutron 中子射线nipple down 卸下，拆卸nipple seating 座落接头no return 未返回水泥浆normal circulation 正循环normal butane 正丁烷normal pentane 正戊烷nozzle size 水眼尺寸nut 螺母Ooff bottom 不接触井底office 办公室oil base mud 油基泥浆oil reservoir 油层on bottom 接触井底open 打开open hole 裸眼opening 扩眼o-ring O环outer barrel 外岩心筒oven 烘箱over pulling 遇卡overshot 打捞筒Ppacker 封隔器packing 密封圈paint 油漆panel 面板paraffin plugging 蜡堵paraffin valve 清蜡闸门paraffin-treatment 清蜡处理paraffin-troubles 结蜡井parts 零件pentane 戊烷PH control additive PH控制剂phenolphthalein 酚酞pile hammer 打桩机pin 销子,公扣pincers 钳子pipe wrench 管子扳手piston 活塞piston rod 活塞杆pit drill 防喷演习pit level 泥浆液面pit level 泥浆池液面pit volume increase 泥浆增加量plastic viscosity 塑性黏度plug 水泥塞plug container 水泥头plug flow 塞流plugging back cementing 回堵注水泥pollution 污染polymer 聚合物portland cement 硅酸盐水泥potassium chlorate 氯化钾power slip 动力卡瓦power source 电源power swivel 动力水龙头power tong 动力大钳power law model 幂律模型pressure decline 压力降pressure equilibrium 压力平衡pressure gage 压力表pressure gradient 压力梯度pressure gradient 压力梯度pressure loss 压力损失pressure loss in pipe 管内压力损失pressure of mud column 泥浆柱压力pressure loss in annular 环空压力损失pressurized air 压缩空气preventer of double ram type 双闸板式防喷器production 生产propane 丙烷pry bar 撬杠，杠杆pull out of the hole 起钻pulley 滑轮pulley 滑轮pulling slip 起卡瓦pumice 浮石pump count 累计泵冲数pump efficiency 泵效pump pressure 泵压pump speed 泵速pump stroke counter 泥浆泵冲数pup joint 短接put into gear 挂挡put on break 刹车，制动PWV(production wing valve) 生产翼阀Qquick coupling 快速接头，快接管箍Rradio operator 电报员radioactivity log 放射性测井rag line 大棕绳rain density 颗粒密度rat hole 鼠洞rate of penetration 转速reamer 释放，丢手reaming 辊轴扶正器recorder 划眼red lead 记录仪reducer 丝扣油，铅油，管件润滑油regular 大小头release 正规扣relief valve 泄压阀,泄流阀reserve pit 储存池reservoir pressure 油层压力retarder 缓凝剂return 返回水泥浆return mud 反出泥浆returning fluid 井口反出液reverse circulation 反循环reverse circulation 反循环revolution 运转revolution 转数revolutions per minute 每分钟转数Reynolds number 雷诺数rig down 拆卸钻机rig up 安装钻机rig in 安装,连接rig out 拆卸ring gasket 钢圈/垫圈riser 隔水导管rope damp 绳头,绳卡rotary hose 泥浆水龙带rotary slip 转盘卡瓦rotary speed 转盘转数rotary table 转盘rotation bases 倒班roughneck 钻工roustabout 水手run casing 下套管run in the hole 下钻run length 进尺run bridge plug 下桥塞run gauge cutter 通井running tool 下入工具running in test 试车running repair 日常修理,现场维修RWTO(returned well to production) 井恢复生产Ssafety belt 安全带safety clamp 安全卡子safety joint 安全接头safety valve 安全阀sampling depth 取样井深sampling interval 取样间隔sand bridge 砂桥sand trouble 砂堵sandline 捞砂绳saturated salt-water mud 饱和盐水泥浆screw 螺钉seal 密封/封堵seating nipple 座落接头sea-water mud 海水泥浆sensor 传感器separater 分离器set back 立根盒setting slip 放卡瓦shaft 轴shale shaker 振动筛shallow gas 试气层shear rate 剪切速度shear pin 剪切销钉sheave 滑轮shock sub 减振器shoe guide 引鞋short trip 短起下钻shut in 关井shut in casing pressure 关井套管压力shut in drill pipe pressure 关井钻杆压力shut in pressure 关井压力shut off 关闭side wall neutron log 井壁中子测井silicon flour 硅粉silicon-controlled rectifier 可控硅整流器single joint elevator 单根吊卡single ram 单闸板slip 卡瓦slip type elevator 卡瓦式吊卡slip velocity 沉积速度slip workline 倒大绳slow pump 低泵速sludge tank 加重泥浆池slush pump 泥浆泵socket 插座solid content 固体含量sonic log 声波测井sonic wave 声波spacer 隔离液spare parts 备件spider 卡盘spontaneous potential log 自然电位测井spool 四通spring 弹簧spud in 开钻squeeze cementing 挤水泥stabilizer 扶正器stabilizing agent 稳定剂stage cementing 分级注水泥stainless steel 不锈钢stand 立柱stand pipe 立管stand the test 试验合格,经受考验standby 待机stand-by boat 值班船starting outfit 启动设备static pressure 静压steam 蒸气sticking 卡钻/被卡stinger 导向插头,引鞋,尾管stinger sub 插入式短节stop lost circulation 堵漏storm 风暴straight well 直井眼sub 接头,短接submerged pump 潜水泵substructure 井架底座sucking line 上水管线suction tank 吸入池supercharge pump 泥浆灌注泵supervisor 监督supply boat 供应船support 支架surge pressure 冲击压力suspending weight 悬重swab pressure 抽吸压力swabbing 抽吸switch 开关TT/B/G 牙齿/轴承/外径磨损table torque meter 转盘扭矩表table height 转盘高度taper milling 锥形刮刀technician 技术人员，技师tee 三通temperature log 温度测井ten minutes gel 终切test paper 试纸thread 丝扣tie back tool 回接工具tighten 上紧TOF(top of fishing) 落鱼顶部tong 大钳tong torque meter 大钳扭矩表ton-mile 吨-英里TOOH(tool out of hole) 起出下入井中的工具tool joint 钻杆接头tool pusher 钻井技师top valve 采油树清蜡闸门,试井闸门torch burner 喷灯torque 扭矩total depth 总井深total gas 气全量total pit 泥浆池总体积tour Shift 班towing 拖航transmission 传动装置/变速器traveling block 游动滑车tri-cone bit 三牙轮钻头trip 起下钻trip tank 计量罐tripping time 起下钻时间tubing 油管tubing hanger 油管挂tubing spool 油管四通tubing head 油管头tubing pressure 油压turbo drill 涡轮钻具turbulent flow 紊流twist off 脱扣typhoon 台风Uunconnect switch 非接触式开关unfreezing 解卡unlatching elevator 开吊卡unloading 卸栽upset 加厚Vvalve master 主阀variable density log 变密度测井V－door 井架大门vent pipe 放空管ventilate 放空,吹扫ventilation 通风,通风设备vertical depth 垂直深度viscosity 黏度volume inside pipe 管内容量volume of annulus 环空容量WW.O.O(wait on orders) 等待指令wait on 等指令wait on cement 候凝wait on(stand by) 待命walkie-talkie 对讲机wall scraper 井壁刮刀WAP(well performance analysis) 井的动态分析warning board 警告牌wash over 洗井,套洗,冲刷wash tank 洗罐,分离罐washer 洗衣机wash-over fishing operation 套洗打捞作业,套洗落鱼作业water flood pump(injection) 注水泵water flush 水循环洗井water injector(injection well) 注水井water lost(WL) 泥浆失水wax containing crude 含蜡原油waxy 蜡,蜡状物,含蜡的WDBS(weight going down before sticking) 仪器遇阻前下行重量weather 气候WEG(wireline entryguide) 喇叭口weight in air 空气中重量weight in mud 泥浆中重量weight indicator 指重表weight material 加重剂weight on bit 钻压weighted mud 重泥浆/加重泥浆welder 电焊工well 井well cleaning 洗井well head 井口well head assembly 井口装置well head pressure 井口压力well shooting 地震测井well bean 井口油嘴well blowout 井喷well bore clean up 洗井,well cementation 固井,挤水泥well cementing operation 固井作业well completing data 完井资料,数据well completing fluid 完井液well completinginformation 完井资料, wellcompleting test 完井测试well completion 完井well condition 井况well control device 井控装置well control equipment 井控设备well control fluid 压井液well control information 井控资料well control manifold 井口控制管汇well control operation 压井作业well deflection 井斜well flow under balance 诱喷well killing 压井well killing job 压井作业well killing method 压井方法well performance testing 系统试井,井动态测试,井生产测试well pulling job 起油管作业well pulling service 修井起下作业well sampling 井下取样well sand up 油井砂堵well screen 油井筛管well service tank 修井液罐well service hoist 修井机well service work 修井作业well site illumination 井场照明well testing supervisor 试油,测试监督well-completion practice 完井作业wellhead cap 井口帽wellhead choke 井口油嘴wellhead control valve 井口总阀门wellhead tap 井口短节wetting agent 润滑剂WHP(wellhead platform) 井口平台wiper trip 通井wire 钢丝wire line(WL) 电缆work accident 操作事故work assignment 工作安排work string reciprocation 工。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
drilling crew 钻井队drill floor,rig floor,floor 钻台drawworks 绞车well-site, rig-site 井场rig manager 平台经理DC (drill collar) 钻铤drilling engineer 钻井工程师DP (drill pipe) 钻杆toolpusher 带班队长rotary table 转盘driller 司钻assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工liner 缸套motor fire man 司机（motorman）wellhead 井口circulation & solid system 循环固控系统machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令) cathead 猫头caravan 营房，大篷车tong 大钳elevator 吊卡well depth 井深slip 卡瓦makeup 上扣spud in 开钻breakout 卸扣ROP (rate of penetration),drilling speed, penetration rate 钻速trip 起下钻diesel-engine 柴油机loss circulation 井漏，循环漏失working uniform 工作服brake handle, brake bar 刹把water well condition 水井井况circulating tank, circulation tank 循环罐normal drilling 正常钻进reserve tank 储备罐parameter 参数trip tank 补给罐，尖底罐, 起下钻泥浆罐（起下钻计量罐）rotary speed 转盘转速（转速）shale shaker 振动筛pump pressure 泵压WOB (weight on bit) 钻压mesh 目,网孔;啮合,编织torque 扭矩screen cloth 筛布displacement 排量safety meeting 班前会pump stroke 泵冲shift exchange 交班、（倒班）mud pump 泥浆泵master 师傅,主人;征服,控制,精通in charge of 负全责,经营,照顾obtain 获得,得到according to 根据,依照normal 正常的,正规的,标准的introduce 介绍,传入,引进,提出progress 前进,行进,进展supervisor 监督location 井场,井位inspection 检查,考察,验收cellar 方井soild (control) system 固控系统waste pit 污水池、废水池Top Drive (Drilling System)顶(部)驱(动)钻井系统Project Department 项目部on duty 值班modify 整改、修改clinic 医务室electic al rig 电动钻机disconnect 拆开,分离,断开pipeline 管线order 指令,命令,顺序Company 公司,甲方Operator 业主,甲方Contractor 承包商,乙方pump house 泵房schedule 时间表,进度表size 尺寸,大小,尺码information 通知,信息,资料equipment 设备,装备,器材instruction 指令,指示,说明书SCR house 可控硅房replace 更换,替换,代替brake shoe 刹车块wear out 磨损safety 安全,保险,安全设备fax 传真guy 家伙,人standpipe 立管Campsite 营地crownblock 天车traveling block 游车dog-house 司钻休息室(钻工值班房)rat hole 大鼠洞mouse hole小鼠洞spudding inspection 开钻验收fill in 填充catwalk 狭窄的过道,高空走道;高台,天车台casing float collar 套管浮箍casing float valve 套管浮阀casing guide shoe 套管引鞋cement水泥,注水泥,结合剂,胶结剂plug 插头safety pin安全销glove手套quick-connector快速接头fire exting u isher灭火器stretcher担架First Aid紧急救护control board控制板weight mdicator指重表rotary torque indicator转盘扭矩表sling吊绳绳套deadline anchor死绳固定器brake system刹车系统drum滚筒safety line保险绳safety belt安全带hydraulic tong液压大钳slip卡瓦（和上面的重复）elevator吊卡（和上面的重复）bit breaker钻头盒chain tong链钳pipe tong管钳wrench板手pliers钳子、老虎钳scissor剪刀cable slot电缆槽vacuum degasser真空除气器butterfly valve蝶阀desilter除泥器desander除砂器degasser除气器mud gun泥浆枪agitator搅拌器leakage漏,泄漏,渗漏barite重晶石hopper漏斗piston活塞union由壬fuel tank燃油罐、高架罐remote control station远控房BOP stacks防喷器组kill line 压井管线choke line节流管线blowout preventer防喷器annular环空ram闸板low pressure低压fire blanket消防毯fire sand防火砂kitchen厨房storeroom储藏室bathroom卫生间(浴室)spudding date开钻日期spudding time 开钻时间string钻柱BHA（bottom hole assembly）井下钻具组合drilling jar随钻震击器drill box钻杆盒drilling program钻井程序、钻井指令drilling fluid钻井液mix up混和、调配、混淆mud material泥浆材料LCM（lost circulation material）堵漏材料、堵漏剂mud engineer泥浆工程师day tour白班night tour夜班drilling progress钻井进度routine inspection例行检查、日常cave in塌陷、塌下、井壁坍塌loss漏失kick井涌hole section井段casing setting depth套管坐封深度downhole problem（trouble）井下事故(井下复杂情况)undergauge 缩径tight hole井径缩小的井眼tight spot （井径）缩小点、缩小段footage钻井进尺formation地层、岩层、构造、组织make up a joint接单根（立柱）sticking 粘附、刺、卡钻sticking point卡点free point解卡点？？hook weight悬重unfreeze解卡back-off倒扣fishing 打捞sidetrack侧钻back reaming倒划眼soak oil泡油soak releasing 泡解卡剂slough off坍塌ream down划眼borehole operation井下作业deviational survey 井斜测量（测斜）make a trip 起下钻bouncing 跳跃的、大的、重的、跳钻bit bouncing 蹩跳bit balling 泥包钻头cutting 切削、切割、切屑、钻屑cutting sample 砂样mud logging 综合录井sandstone 砂岩Pooh(pull out of hole) 起钻RIH(run in hole)下钻junk 落物、金属屑、碎物junk sub 打捞（落物）接头scrape 擦、刮、擦痕、刮掉bit gauge 钻头规centralizer 扶正器hold pressure 蹩压day rate 日费standby rate 等待日费、待命费run casing下套管cementing operation固井作业drift casing套管通径？？clean thread洗扣geologist地质师、地质学家casing shoe套管鞋thread protector护丝casing tong套管钳wiper trip通井rigid centralizer刚性扶正器guide shoe引鞋float-collar浮箍accident事故、意外事件slurry水泥浆WOC（waiting-on--cement）候凝期nipple up安装（防喷器）primary cement job正注固井wireline log电测test pressure 试压International practice国际惯例choke manifold节流管汇lay down the string倒钻具nut螺母bolt螺栓、螺钉screw bolt螺栓、螺杆pipe ram半封闸板shut-down停工HWDP (heavy weight drill pipe) 加重钻杆calibrate 校正、定标judgment 判断bleed off lin e排砂(排放)管线commence 开始、着手isolate 隔离、隔绝、绝缘welding 焊接、压实、压结mud property 泥浆性能MW(mud weight) 泥浆比重mud density 泥浆密度funnel viscosity 漏斗粘度PV(plastic viscosity) 塑性粘度well control drill 井控演习、防喷演习increase 增大、增加、增大decrease 减少、降低；减少之量pressure gauge 压力表casing pressure 套(管)压(力)choke valve 节流阀coring operation 取心作业hole collapse井壁坍塌pressure surge 压力激动、压力涌动bump pressure 碰压cement head 水泥头re v erse circulation 反循环cement 水泥，注水泥；结合剂；粘紧，粘牢(重复) cement accelerator 水泥促凝剂cement hardener 水泥速凝剂, 水泥硬化剂cement head (注) 水泥头cementing jobs 注水泥作业cement job 固井作业cement squeeze 挤水泥bonus 奖金,红利completion job 完井作业hand pump 手摇泵,手压泵workshop 车间,工场nipple down 卸下nipple up 装上,接上,装配,安装(重复)ID (inside diameter) 内径torque-on-bit 钻头扭矩tubing bonnet 油管头tubing hanger 油管悬挂器, 油管挂tubing joint 油管接箍landing head (悬挂油管用)油管头,(油管)联顶头landing joint 联顶节[下套管或油管联顶时用] TBG (tubing) 油管spacer fluid 封隔液mud logging unit 综合录井仪cooperation 合作,协作sample sack 砂样袋engage 从事;啮合deadline anchor 死绳固定器,死绳锚(重复) drilling cost 钻井成本evaluate 评价,估价,求…的值in advance 预先overpressure 过压，超压力swab 抽汲eliminate 排除,消除pipe bouncing 钻具蹩跳drill string failure 断钻具twist-off 脱扣horizontal well 水平井vertical well 垂直井stainless steel 不锈钢anticline 背斜porosity 孔隙度potential 潜在的,可能的; 潜能,潜力densimeter 密度计communication 传达,信息,交流,通讯hook velocity 大钩速度verify 检验,查证,核实confirm 确定,批准,印证incredible 难以置信的round trip 起下钻resume normal drilling 恢复正常钻进goal 目的,目标understanding 理解,认识,谅解kill operation 压井作业wireline [electric] log 电测井GR 自然伽玛scrap iron 铁屑cotton yarn 棉纱paint 油漆cavern 大山洞,大岩洞,溶洞,穴fossil 化石;陈腐的,守旧的gas-bearing 含气的water-bearing 含水的DST(drill-stem test) 中途测试, 钻杆测试water loss 失水flow pressure 流动压力daily output 日产量target zone 目的层finishing drilling 完钻thermometer 温度计re v er s e circulation 反循环build up 建造，安装；压力增加，压力恢复build up a joint??Well Control & Drill Procedures井控措施及防喷演习程序LIST OF ABBREVIATIONS缩写表BHP - Bottom-Hole Pressure 井底压力BOP - Blow out Preventer 防喷器（重复）CDPP - Circulating drill pipe pressure 循环钻杆压力CP - Casing pressure 套管压力（重复）CSG – Casing 套管（重复）DC - Drill collar 钻铤DP - Drill pipe 钻杆ECD - Equivalent circulating density 当量循环密度EMW - Equivalent Mud Weight 当量泥浆比重FCP - Final Circulating Pressure 最终循环压力Gm – Mud weight 泥浆比重HPHT - High pressure high temperature高压高温HWDP - Heavy Weight Drill Pipe加重钻杆（重复）ICP - Initial Circulating Pressure初始循环压力LOT - Leak-Off Test地漏测试MAASP - Maximum Allowable Annular Surface Pressure最大容许环空表面压力MD - Measured depth测量深度MEMW - Maximum equivalent mud weight最大当量泥浆比重Ps - Static pressure静压力Q - Flow rate 流量ROP - Rate of penetration机械钻速SICP - Shut-in Casing Pressure关井套压SIDPP - Shut-in Drill Pipe Pressure关井钻杆压力TVD - Total vertical depth垂直总深kill and choke lines 压井和节流管线kill fuild 压井液killing well 压井kill job 压井作业kill line压井管线kill rate 压井排量kill string 压井管柱kill-weight-fluid 加重压井液，高比压井液operating skill 操作技巧view point 观点engage in 从事，啮合primary control 首要控制，一次井控secondry control 二等控制，二次井控tertiary control第三位控制，三次井控safety margin 安全系数circulate out循环带出wildcat 探井pressure surge 压力波动，压力骤增（重复）Kick Control Sheet 井涌控制表circulating bottoms up循环井底至井口的泥浆行程active mud system在用泥浆系统fill the hole 灌满井眼human failure 人为事故differential pressure压差additive 添加剂obstruction阻塞，阻挡evidence 迹象，证明lower Kelly cock 方钻杆下旋塞upper Kelly cock 方钻杆上旋塞stripping 强行起下钻potential 潜在的，可能的；势，位shut-in procedures 关井程序，关井步骤soft shut-in procedures 软关井程序with a careful eye on留心saver sub 保护接头pipehandler 管子操作装置Driller’s Method 司钻法water-based system 水基体系implement 执行overcome 克服Daily Drilling Report 钻井日报表up-to-date 现代化的，最新（式）的，当今的chilksan line活动弯头管线H2S ( hydrogen sulfide) 硫化氢Muster point (Muster board) 紧急集合点（紧急集合点标识牌）Wind sock 风向标SCBA (self-contained breathing apparatus) 呼吸器Oxygen, acetylene 氧气，乙炔Alarm 警报Ambulance 救护车Emergency team 应急小组Fire pump, Fire drill, Fire hose, ax, rope 消防泵，消防演习，消防水龙带,消防斧，消防绳JSA (job safety analysis)工作中安全因素分析HSE (health, safety and environment) 健康，安全，环保Escaping route 逃生路线Inflammables 易燃物品Work Permit (Permit to Work) 工作许可（证）Safety meeting for running casing, liner, electric log 下套管，尾管，电测安全会PPE (personal protection equipment) 劳保用品Special operation 特殊作业Vehicle inspection 车辆检查Housekeeping 打扫卫生Crane 吊车MSDS（material safety data sheet）泥浆药品安全使用手册first aid box 急救箱Helmet安全帽Safety glasses 护目Fall arrester 防坠器VIS (viscosity) 粘度PV (plastic viscosity) 塑性粘度（重复）YP (yield point) 屈服粘度(流动点)Gels (gel strength) 静切力(胶凝强度)low viscosity低粘high viscosity (hi-vis)高粘lightweight low-viscosity mud低比重低粘泥浆water tank水罐caustic soda 烧碱dangerous 危险sand trap 沉沙罐、锥形罐trip tank 计量罐pill tank加药罐waste pit 排沙池fluid loss 失水。