船体检查英语词汇
船体检查英语词汇
船头一、bit 系缆桩bollard 系缆桩bow 船首bow fender 艏护垫bow flare 艏部外飘bow thruster艏侧推器bow anchor 艏锚bow frame 舟包部肋骨bow chock艏导缆口bow stopper制链器bulbous bow球鼻艏break water 挡浪板cable stopper制链器bulb stem 球式艏柱chain pipe锚链管chain locker 锚链舱chain stopper止链器chock 导缆器系绳铁栓防滑条cleat羊角clamp plate夹板垫木绞盘capstan capstan绞盘筒首楼collision bulkhead 防撞舱壁forecastle fore peak tank首尖舱首楼甲板forecastle deckground tackle 锚泊索具foundation 底座锚链筒gypsy绞筒（锚机绞车上的）hawse pipe hawser 大缆锚链孔hawse hole锚链孔盖hawser clamp锚链挚hawse buckler/flap 导缆孔mooring hole 系缆柱mooring post尾柱astern post warping chocks滚轮导缆钳windlass起锚机绞车卷筒winch-headwire clip钢缆夹wire reel 钢丝滚筒卷缆车1flush deck 平甲板gunwale圆弧过渡舷边adapting连接管管接头air hole空气管air pipe通风管air funnel货舱通风筒amidships船中部air and sounding pipeappendages 船体附属体（包括舵机和螺旋桨等）base line基线Batten板条压条batten cleat舱口契耳batten down封舱batten seat板条坐架压条架batten wedge封舱契batten ceiling（货舱内）护舱条护板batten bar舱围压条beam bracket/knee 梁肘板bevel斜角斜面bevel angle斜角坡口角度bevel board斜角板bevel edge斜边bevel face斜面bevel frame斜边肋骨bilge舟比部bilge bracket舟比肘板bilge knee舟比肘板bilge keel(chock piece)舟比龙骨bilge line 污水管道bilge pipe 污水管bilge well/sump污水井bilge pump污水泵bilge tank污水舱bilge alarm system污水警报系统bilge discharging pipe boom吊杆污水排放管bilge inlet 污水收集口bilge keelson舟比龙骨bilge sounding pipe 污水测深管bilge plug 污水塞bottom longitudinal 底部纵桁bottom frame 底部肋骨2bottom plating 舱底板bridge驾驶台cat walk bridge 纵向天桥，步桥catwalk catway纵向天桥，步桥bridge fittings桥式连接器（集装箱桥锁）bridge wing 驾驶台两翼bridge space 驾驶台bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强板bulwark舷墙bulwark brace舷墙斜撑bulwark plating 舷墙板bulwark stay舷墙扶强材bulwark freeing port舷墙排水口camber of a ship 中拱hogging 中拱sagging中垂camber of beam拱梁cant frame斜梁cant bracket 斜角板cant frame斜肋cantilever beam 悬梁cantilever悬臂梁cargo batten 货舱护板cargo block 吊货滑车centerline cargo port 装货舷门中心线center strake 中央内底板center girderchafing ring 防擦环chafing plate防擦板collar plate封板槽型舱壁corrugated bulkhead crossing deck structure槽型的交叉甲板结构corrugationcrossing strength member 交叉强力结构cofferdam隔离舱cutout 开口davit吊艇架deck beam甲板横梁deck 甲板deck line 甲板线deckhouse 甲板屋3deck longitudinal甲板纵桁deck plate甲板边板derrick 吊杆甲板上的舱deck tankdesigned waterline breadth设计水线宽designed waterline length 设计水线长doubling plate 双层焊合板drain hole排水孔dunnage 垫舱duct keel箱型龙骨dunnage wood 垫木dynamic load动载荷diaphragm plate 隔板expansion trunk(油船)膨胀深井extension bracket 延伸肘板最大宽度extreme breadth face plate 表层板fender靠垫fender barflame screen防焰罩护舷条flange折边flange bracket折边肘板flat keel平板龙骨肋板floorfolding door折门flame space肋（骨间）距freeing port甲板排水孔flame number肋骨号gasket 垫圈垫料handrail 舷墙扶手goose neck 鹅颈头吊杠弯头gunwale舷缘舷边gunwale angle舷边角钢舷边角材gunwale bar gunwale tank舷侧水柜舷边栏杆gunwale railing 槽沟（甲板）水沟gutter gusset 角板扣板gutter angle waterway angle（舷侧）排水沟角钢hanging rudder 密封条hatchway 舱口槽hatch bar封舱压条舱口hatch opening4hatch batten舱口边压条hatch beam(web)舱口大梁hatch coaming舱口围板hatch booby活动舱口盖hatch end beam舱口端梁舱口盖hatch coverhatch tarpaulin舱口帆布盖hatch side girderhand nut蝴蝶螺母hatch trunk舱口围井hold货舱hinged cover(door)铰链盖hold frame舱内肋骨舱口横梁hold beamhold stanchion(pillar)舱内支柱货舱梯hold ladderhopper tank Hopperhorizontal girderHopper tank sloping platinghorizontal stiffener水平扶强材horizontal margin plate 水平内底板船体结构hull construction hull船体船体强度hull strength 船体板hull plating内底板inner bottom plating inner bottom 内底板横断面交点intersection 交叉insert plate嵌板衬板r 绳梯jack ladder 顶千斤jackJacob's ladder折接弯合joggled joint 软梯绳梯keel龙骨joggled machine折曲机keelblock龙骨墩龙骨线keel line龙骨板keel plate （救生艇）艇底把手keel rail 将军柱龙骨板keelson kingpost起重柱肘板knee knee of the deck 甲板梁肘板5knee pipe 弯管knee plate肘板lighting hole 减轻孔knukle折角线local stress 局部应力local strength 局部强度longitudinal bulkhead 纵舱壁纵骨longitudinallongitudinal bending纵向弯曲longitudinal frame system纵骨架式longitudinal strength lug耳板总纵强度main frame主肋骨main deck 主甲板manhole 人孔manhole door人孔门man hole coaming 人孔围板margin plate内底边板molded depth型深molded breadth型宽notch切口non-watertight bulkhead非防水舱壁oscillating load震动负荷parallel middle body平行舯体panting arrangement防桡震结构panel stiffener 板格扶强材panting beam防桡震梁panting stringer 防桡震纵材舱壁板plane bulkhead 墩pillar 支柱/plane keel 龙骨板pump room泵间horizontal margin plate水平内底边板out bottom plating platform 平台plating外板rail栏杆racking( 船体)横向扭变register length(breadth depth) 船底斜高rise of floor(dead rise)rolling横摇round of beam拱梁rung(梯子) 踏步扇形开口scallop ,横挡6scantling构件尺寸scantling of the structure结构尺寸scarf joint斜(嵌) 接scarf/scarph嵌接处scarf weld(斜面)焊接scarf bracket铅接肘板scupper排水孔scupper pipe排水管section modulus 剖面模数section剖面sheer舷弧shedder plate 斜板, 泄板forward(after)perpendicular首尾舷弧sheer line舷弧线sheer strake 舷顶列板shell船壳shelter deck遮蔽甲板shell plating船壳板shifting beam移动舱口梁shifting board(plank)止移板single bottom 单层底side longitudinal边纵桁skidside plating边板护舷木sloping plate斜板slanting plate斜板sloping plate longitudinal 油水舱纵向板slot槽,开缝sluice水(密)门,水闸sluice valve闸阀soft toe 软趾sniped end消斜端sounding pipe 测深管solid floor实肋板stabilizing tank stabilizerstanchion支柱,栏杆柱staging 架构,台架,手脚架stay 支柱stay bar撑杆,撑条,支索加强甲板strength deck stay plate 撑板stringer plate 构件structure member 甲板边板7structure strength结构强度strumbox(舱底水)过滤箱stuffing box填料箱strut 撑材tieplate带板, 牵板, 连接板tarpaulin 帆布topside tank顶边水舱扭转torsiontorsion strength扭转强度vertical ballast trunk 竖向压载通道transverse横梁,横材transverse bulkhead横向舱壁transverse framing system横骨架式transverse frame横梁transverse ring 横梁令环transverse strength横向强度tween deck二层甲板tripping bracket防倾肘板tween deck frame扭转变形二层甲板肋骨twisting distortionupper deck上甲板upper(lower)shelf plate上(下)支架板ventilator通风管upper(lower)stool 上(下)托架wash bulkhead制荡舱壁plimsoll line载重线watertight bulkhead 水密舱壁watertight door 水密门web frame 加强肋骨web plate复板winch 起货机wedge 契子wing tank 翼舱,翼柜ballasting pump system 压载水泵系统aft draft 尾吃水ballast压载水ballast pump 压载泵ballast line压载线even keel平吃水,平载draft figures 吃水尺度floodable length 可浸长度fresh water loadline淡水载重线fresh water timber load line 淡水木材载重线8length between perpendicular首尾间柱长ballast tank压载舱length overall 总长loadline mark载重线标识freeboard mark 载重线标识freeboard assignment干舷划定freeboard deck 干舷甲板freeboard depth 干舷深度plimsoll mark 载重线标记freeboard zone 干舷区plimsoll disc/loadline disc载重线标圈load waterline length满载水线长moment of inertia惯性矩static load 静负荷strength calculation强度计算summer loadline夏季载重线summer fresh water loadlin夏季淡水载重线etropical loadline热带载重线tropical fresh water loadline热带淡水载重线twisting moment 扭矩winter load line冬季载重线winter North Atlantic load line北大西洋冬季载重线bunker tank 燃油舱bushing 衬套butt joint /seam 平接缝butt 端接butt welding对接焊but riveting 对接铆butterfly clip 蝴蝶夹bypass valve 旁通阀sheer strake列板船舷上缘gunwaleside longitudinal 边纵main frame主肋骨tweendeck frame二层甲板肋骨intermediate frame内中肋骨web frame强肋骨hatch coaming/hatch side coaming舱口围板side shell longitudinal 船壳纵向边板side shell plating船壳边板fire hydrant消防水龙9hose 软管nozzle喷头fire extinguisher灭火器portable foam applicator unit移动泡沫枪单元quick closing valve 速闭阀remote control shut off遥控关闭funnel skylight 烟囱天窗shutter ventilator通风管道关闭器properly closed 正常关闭防火盖fire damperventilator通风管重起resethigh pressure fuel pump高压燃油泵duct 管道fuel injector jacked pipe管路套油泵喷口high pressure fuel deliver line输送管道external外部的outside diameter外径flange法兰washer垫圈nuts螺母螺栓boatsdimension 尺寸gasket垫片fixed gas fire-extinguishing system.固定灭火系统fixed high expansion foam fire-extinguishing system固定高效泡沫灭火系统fixed pressure water-spraying fire-extinguishing system固定高压水雾灭火系统storage room储藏间fire extinguishing medium灭火介质protected area 保护区域water/ spray nozzle水/雾两用喷头pressure gauge 压力表泡沫炮monitorfixed detection and fire alarm固定灭火探测警报automatic sprinkler 自动喷淋Spare parts备件10sample extraction smoke detection system烟雾探头manually operated call points人工操纵报警点smoke detector/thermal detector烟雾/热能探头audible and visual alarm音响和视觉警报operational readiness操作说明maintenance plan保养计划training manual训练手册fire safety operational booklet(fob)消防手册emergency fire pump 应急消防泵portable emergency fire pump移动应急消防泵diesel engine柴油机vacuum pump真空泵functional requirementscontainment of fire 要求功能method 1C control station集中控制站1C 形式corridor 走廊stair way 楼梯low risk service space 低风险服务区blower鼓scrubber 洗涤塔deck seal甲板水封inert gas deck main惰性气体甲板主管oxygen氧气nitrogen氮气inert gas generator惰性气体发生器manually operated valve 人工操纵发7no-return valve 止回阀wing tank翼舱slop tank 污油水舱中间舱center tanksub panel 幅面板main panel 主面板11sea chest/valve 海水箱/阀hydrocarbon gas碳氢化合物pressure/vacuum breake压力/真空保护装置accommodation space 住宿区“A”class division“Ａ”级隔离central control station 中央控制台fire door 防火门fire safety system code防火安全程序代码fire test procedure code 防火试验程序代码main vertical zone主竖区machinery space 机器处所public space公共区oil fuel unit 燃油单位service space服务区machinery space of category AＡ级机器处所other machinery space其他机器处所cargo space货物间high risk service space高风险作业区weather deck风雨密甲板open deck开敞甲板ro-ro and vehicle space滚装船车辆处所openings开口fire resisting division 防火分隔coming围板fire integrity of bulkheads separating横舱壁分隔防火完整性adjacent spaces附近区域fire integrity of decks separating甲板分隔防火完整性12。
船舶常用英语
1、HULL PART 船体部分1、1结构 Structure1 2船厂 dockyard/shipyard 船坞 dock/boatyard船东 ship-owner 船舷 Ship's side船码头 quay/dock 船的栏杆 Ship's rail船舱 hold 甲板 Deck船籍 Ship's registry 住舱甲板 accommodation deck 船首 bow 梁拱甲板 arch deck船梯 ladder 载货甲板 cargo deck船尾 stern 首楼甲板 Forecastle deck上甲板 Upper deck下甲板 Lower deck主甲板 Main deck货舱甲板 Hold deck桥楼甲板 Bridge deck水密甲板 Watertight deck3 4驾驶甲板 Navigation deck 铜-钢复合板 Copper sheathing steel plate艇甲板 Boat deck 甲板边板 Deck stringer plate罗经甲板 Compass deck 斜板 Sloping plate板 Plate 加强板 Reinforcement plate舭板 Bilge plate 舵板 Rudder plate船底板 Bottom plate 舷侧外板 Side plate船外板 Shell plate 裙板 Skirt plate船首外板 Bow plate 首柱板 Stem plate肘板 Bracket plate 尾柱板 Stern plate舱壁板 Bulkhead plate 平台 Platform槽形舱壁板 Corrugated bulkhead plate 机舱平台 Engine-room platform舷墙板 Bulwark plate 分段 Block围板 Coaming plate 首段 Bow block连续板 Connection plate 中段 Midship block5 6尾段 Stern block 甲板下纵桁 Underdeck girder左舷 port 舭纵桁 Wing girder右舷 Starboard 支柱 Pillar纵桁 Girder 肋骨 Frame型材桁 Bar girder 基础台架 Base frame中底桁 Bottom center girder 支架 Bear frame中内龙骨 Bottom center line girder 舭肋骨 Bilge frame底桁材 Bottom girder 船底肋骨 Bottom frame旁桁材 Bottom side girder 首肋骨 Bow frame甲板纵桁 Deck girder 肘板框架肋骨 Bracket frame 横桁 Cross girder 球鼻首肋骨 Bulbous bow frame 水平桁 Horizontal girder 球曲型肋骨 Bulbous frame 舱口边梁 Hatch coaming girder 主肋骨 Chief frame 机座纵桁 Engine girder 首肋骨 Fore frame7桁架梁 Girder frame 舭纵桁舭纵骨 Bilge longitudinal舯部肋骨 Middle frame 船底纵骨/纵桁 bottom longitudinal尖舱肋骨 Peak frame 船底腹板纵桁 Bottom web longitudinal加强筋 Stiffened frame 甲板纵桁 Deck longitudinal 横框架肋骨 Transverse frame 内底纵桁/纵骨 Inner bottom longitudinal肋距 F.S.(frame space) 舷侧纵桁/纵骨 Shell side longitudinal纵桁/纵骨/纵向构件 longitudinal 双层底顶纵骨 Top longitudinal of double bottom8 9斜舱壁纵骨 Slopping-bulkhead longitudinal 舱 Tank结构 Structure 尾尖舱 after peak tank附属结构 Accessory structure 尾部水舱 after water tank全焊结构 All-welded structure 辅助水柜 Auxiliary water tank中部结构 Amidships structure 辅助压载水舱 Auxiliary water ballast tank泊位结构 Berthing structure 污水舱 Bilge tank底部龙骨结构 Bottom keel structure 底舱 Bottom tank船首部结构 Bow structure 底边舱 Bottom side tank 支撑结构 Braced structure 货油压载舱 Cargo and ballast tank桥楼结构 Bridge structure 循环水槽 Circulating flow water tank首楼结构 Forecastle structure 循环滑油舱 Circulating lubricating oil tank构架结构 Framed structure 清洁压载舱 Clean ballast tank纵桁结构 Girder structure 冷凝水柜 Condensate catch tank人孔 manhole 干舱 Dry tank10 11饮用水舱 Drinking water tank 密封圈 Sealing ring 污水舱 Bilge tank 铰链 Hinge应急淡水柜 Emergency fresh water tank 把手 Handle 首舱 Fore tank 平衡块 Balance block首尖舱 Fore peak tank斜边舱 Hopper side tank 1、2 welding焊接液舱 Liquid tank 坡口 Groove龙骨舱 Keel tank 单面坡口 Single groove右舷舱 Starboard tank 双面坡口 Double groove顶边水舱 Topside tank Ⅰ形坡口 Square groove顶边翼舱 Topside wing tank V型坡口 Single v groove小舱口盖 Small hatch cover U型坡口 Single u groove水密舱口盖 Water-tight small hatch cover X形坡口 Single v groove风雨密舱口盖 Weather-tight small hatch cover K形坡口 Single bevel groove12 13Y形坡口 Single v groove with broad rood face 填充金属 Filler metal坡口面 Groove face 热影响区 Heat-affected zone(HAZ)坡口角度 Groove angle 过热区 Overheated zone焊缝倾角 Weld slope 焊合线 Bond line(fusion line) 接头根部 Root of joint 焊接区 Weld zone根部间隙 Root gap 焊缝区 Weld metal area钝边 Root face 焊缝 weld焊接接头 Welding joint 连续焊缝 Continuous weld 对接接头 Butt joint 断续焊缝 Intermittent weld 角接接头 Corner joint 纵向焊缝 Longitudinal weld T形接头 T-joint 横向焊缝 Transverse weld搭接接头 Lap joint 对接焊缝隙 Butt weld十字接头 Cross shaped joint 角焊缝 Filled weld 母材 Base metal(parent metal) 并列断续角焊缝 Chain intermittent fillet14 15交错断续角焊缝 Staggered intermittent fillet 弧焊整流器 Arc welding rectifier焊缝正面 Face of weld 自动焊 Automatic welding 焊缝背面 Back of weld 埋弧自动焊 Submerged arc焊缝宽度 Weld width 半自动焊 Semi- automatic welding焊缝长度 Weld length 氩弧焊 Argon-arc welding焊缝余高 Reinforcement 二氧化碳气体保护焊 CO2 gas shielded arc welding焊脚 Leg(of a fillet weld) 氧乙炔焊 Oxy-acetylene welding焊脚长度 Leg length 气割 Gas cutting套管接头 Muff joint 碳弧气刨 Carbon arc air gouging手工电弧焊 Manual arc welding(shielded metal arc welding) 水下切割 Underwater cutting直流电弧焊 Direct current arc welding 等离子弧切割 Plasma arc cutting交流电弧焊 alternating current arc welding 连续焊 Continuous welding弧焊变压器 Arc welding transformer 断续焊 Intermittent welding点焊 Sport welding16 17对接焊 Butt welding 分段退焊 Back step welding 角焊 Fillet welding 分段多层焊 Block welding搭接焊 Lap welding 深溶焊 Deep penetrating welding返修焊 Re-welding 跳焊 Skip welding补焊 Repair welding 陶质衬垫焊 Ceramic backing welding定位焊 Tack welding 引弧 Striking the arc封底焊 Back sealing welding 焊接工艺参数 Welding condition打底焊 Backing welding 焊接电流 Welding current 堆焊 Surfacing(overlaying) 焊接电压 Welding voltage塞焊 Plug welding 焊接速度 Welding speed槽焊 Slot welding 电弧电压 Arc voltage盖面焊 Consmetic welding 焊丝间距 Wire spacing 前倾焊 Forward welding 空载电压 Open circuit voltage后倾焊 Backward welding 熔化速度 Melting rate18 19送丝速度 Wire feed rate 层间温度 Inter-pass temperature气体流量 Gas flow rate 焊后热处理 Post-weld heat焊丝伸出长度 Wire extension 锤击 Peening极性 Polarity 全焊透 Full penetration welding正极/阳极 Positive electrode 熔池 Weld-pool负极/阴极 Navigate electrode 熔深 Penetration左焊法 Leftward welding 弧长 Arc length右焊法 Rightward welding 喷射过渡 Spray transfer 电流密度 Current density 短路过渡 Short circuiting transfer线能量 Heat input 熔滴过渡 Metal transfer预热 Preheat 焊缝成形 Appearance of weld后热 Post-heat 焊缝成形系数 Form factor of weld 预热温度 Preheat temperature 熔敷系数 Deposition coeffcient后热温度 Post-heat temperature 熔敷效率 Deposition efficiency20 21熔合比 Penetration ratio 立焊 Vertical position welding等速送丝 Constant wire-feed system 仰焊 Overhead position welding变速送丝 alternate wire-feed system 立向上焊 Vertical up welding电弧静特性 Static characteristic of arc 立向下焊 Vertical down welding电弧动特性 dynamic characteristic of arc 单面焊 Welding by one side焊接性试验 Weldability test 双面焊 Welding by both side焊接结构 Welded construction 单道焊 Single-pass welding焊道 Bead 多道焊 Multi-pass welding焊层 Layer 多层焊 Multi-layer welding正接（正极性） Straight polarity 焊接材料 Consumables反接（反极性） Reversed polarity 焊条 Electrode 焊接位置 Position of welding 焊条药皮 Coating平焊 Flat position welding 酸性焊条 Acid electrode横焊 Horizontal position welding 碱性焊条 Basic electrode22 23低氢型焊条 Low hydrogen type electrode 焊丝盘 Wire reel铁粉性焊条 Iron power type electrode 铜冷却板 Cu-cooling plate重力焊条 Gravity electrode 铜滑块 Copper shoe焊剂 Flux 切割 Cutting熔炼焊剂 Fused flux 焊接工作台 Welding bench烧结焊剂 Sintered flux 焊接变位机 Positioner焊丝 Wire 送丝机构 Wire feeder药芯焊剂 Flux-cored wire 行走机构 Traveler保护气体 Shielded gas 焊接车间 Welding shop焊剂垫 Flux backing 引弧板 Run-on tab(end tab) 重力焊条 Gravity electrode 引出板 Run-off tab(end tab)焊剂漏斗 Flux-hopper 定位板 Strong-back流量计 Flow meter 焊接衬垫 Welding backing干燥箱 Dryer 敲渣锤 Chipping hammer24 25面罩 Helmet 条虫状气孔 Wormhole焊工手套 Welding glove 密集气孔 Porosity焊钳 Electrode holder 针尖状气孔 Pinhole焊枪 Welding gun 白点 Fish eye (flake)导电嘴 Tip 切口 Kerf喷嘴 Nozzle 咬边 Undercut焊矩 Torch 焊瘤 overlap焊接缺陷 Welding defect 凹坑 Pit未焊透 Incomplete penetration 烧穿 Burn through 未熔合 Incomplete fusion 未满焊 Incomplete filled groove渣 Slag 清根 Back chipping夹渣 Slag (slag inclusion) 清渣 Slag removal夹杂物 Inclusion 焊接烟尘 Weld fume气孔 Blow hole 电光性眼炎 Eye-flash26 27焊接性 Weldability 横裂纹 Transverse crack碳当量 Carbon equivalent 纵裂纹 Longitudinal crack未焊满 Incomplete filled groove 焊趾裂纹 Toe crack焊接裂纹 Weld crack 机械性能试验 Mechanical property test热裂纹 Hot crack 试板 Test piece冷裂纹 Cold crack 试样 Specimen氢致裂纹 Hydrogen –induced crack 侧弯 Side bend 延迟裂纹 Delayed crack 弯曲 Bending层状撕裂 Lemellar tearing 横向拉伸 Transversetensile弧坑裂纹 Crater crack 宏观试样 Macro-etching specimen根部裂纹 Root crack 微观试样 Micro-examination specimen再热裂纹 Reheat crack 破断试验 Fracture test热影响区裂纹 Heat-effected zone crack 抗裂试验 Cracking test晶间裂纹 Intercystalline crack 脆性断裂 Brittle fracture28 29塑性断裂 Plastic fracture 焊接方法 Welding process焊接残余裂纹 Welding residual stress 焊接工艺 Welding technology消除应力 Stress relieving 焊接操作 Welding operation焊接变形 Welding deformation 焊接顺序 Welding sequence角变形 Angular distortion 焊接方向 Direction of welding外观检查 Visual examination 常用缩语无损探伤 Non-destruction testing(N.D.T.) 气电立焊 EGW超声波探伤 Ultrasonic inspection 药芯电弧焊 FCAW 射线探伤（X光） Radiographic inspection(X-ray inspection) 实心电弧焊 GMAW磁粉探险伤 Magnetic particle inspection 焊剂铜衬垫单面埋弧自动焊 FCB渗透探伤 Penetrate inspection 手工电弧焊 SMAW熔池 Weld-pool 埋弧自动焊 SAW焊机（焊接电源） Weld source30 31钨极惰性气体保护电弧焊 TIG 机舱部分 ENGINE ROOM PART 熔化极惰性气体保护焊 MIG 一、机舱设备 Machines and equipment in engine room活性气体保护焊 MAG 1、主机 Main engine手工电弧切割 SMAC 1）主机油底壳 The sump tank of M.E.2）主机飞轮 Fly wheel of M.E3）活塞 Piston2、发电机 Generator engine1）应急发电机 Emergency generator engine2）辅机 Auxiliary3、锅炉 Boiler1）组合锅炉 The composite boiler2）锅炉安全阀 The safety valve of boiler32 343）燃烧器 Oil burner unit 3）主空气瓶 Main air reservoir4）水位表 Water level gauge 4）应急空气瓶 Emergency air reservoir5）水位控制器 Water level controller 5、控制空气瓶 Control air reservoir6）过量蒸气调节阀 Excess steam pressure control valve 6、空气干燥器 Air dryer4、舵机 7、分油机 Oil purifier1）舵机间 Steering room 1）燃油分油机 Fuel oil purifier2）舵机装置 Steering-gear 2）柴油分油机 Diesel oil purifier3）手操舵装置 Trick wheel plant 3）滑油分油机 Lubricate oil purifier4）油缸 Oil cylinder 4）排渣 Sludge discharge 5）反馈装置 Feedback device 8、制淡装置 Fresh water generator6）舵 Rudder 9、焚烧炉 Incinerator舵叶 Rudder blade 10、油水分离器 Oil water separator舵杆 Rudder stock 11、生活污水处理器 Sewage treat plant上舵承 Rudder carrier 12、大气冷凝器 Atmosphere condenser35 36热水井 Cascade and inspection(hot well) 5）主机燃油供给泵 Main engine fuel oil supply pump滑油自清滤器 The automatic back-flash lubricating oil filter 6）主机燃油增压泵 Main engine fuel oil booster pump 燃油单元 Fuel oil unit 7）主机十字头泵 Main engine cross head pump1）主机燃油单元 Fuel oil unit of M.E 8）付机海水泵 Generator engine sea water pump2）付机燃油单元 Fuel oil unit of A.E 9）付机缸套水泵 Generator engine cylinder cooling water pump3）粘度计 Viscosity controller 10）锅炉给水泵 Feed water pump of boiler泵 Pump 11）锅炉燃油泵 Fuel oil pump of boiler 1）主机滑油泵 Main engine lubricating oil pump 12）分油机供给泵 Fuel oil supply pump of purifier2）主机缸套水泵 Main engine cylinder cooling water pump 13）制淡海水泵 Sea water pump of fresh water generator3）主机缸套水预热泵 Main engine cylinder cooling water preheating pump 14）压载泵 Ballast pump4）主机海水泵 Main engine sea water pump 15）舱底消防泵 Bilge and fire pump37 3817）油渣泵 Sludge oil pump 2、柴油澄清舱 Diesel oil setting tank18）柴油输送泵 Diesel oil transport pump 3、燃油日用柜 Fuel oil daily tank19）燃油油输送泵 Fuel oil transport pump 4、燃油澄清舱 Fuel oil setting tank20）汽缸油输送泵 Cylinder oil transport pump 5、滑油澄清舱 Lubricating oil setting tank21）淡水输送泵 Fresh water transport pump 6、滑油储藏舱 Lubricating oil store tank22）热水循环泵 Hot water circulating pump 7、滑油循环舱 Lubricating oil circulating tank23）饮水日用泵 Drinking water pump 8、燃油溢油舱 Fuel oil overflow tank舱底消防总用泵 Bilge, fire and G.S pump 9、燃油油渣舱 Fuel oil sludge tank喷淋泵 Sprinkling pump 10燃油深舱 Fuel oil deep tank停泊海水泵 Harbor sea water pump 11滑油污油舱 Lubricating dirty oil tank12滑油溢油舱 Lubricating oil overflow tank 二、各种舱（箱）柜 All kinds of tank 13滑油油渣打舱 Lubricating oil sludge tank1、柴油日用柜 Diesel oil daily tank 14主机淡水膨胀水箱 M.E fresh water expansion tank15付机淡水膨胀水箱 A.E fresh water expansion tank39 4016、淡水压力柜 Fresh water pressure tank 1、滑油系统 Lubricating oil piping system17、热水压力柜 Hot water pressure tank 2、燃油系统 Fuel oil piping system18、饮水压力柜 Drinking water pressure tank 3、海水系统 Sea water piping system19、淡水舱 Fresh water tank 4、缸套水系统 Cylindercooling water piping system20、饮水舱 Drinking water tank 5、启动空气系统 Start air piping system21、锅炉水舱 Boiler water tank 6、控制空气系统 Control air piping system22、分油机工作水箱 Purify operating water tank 7、排气系统 Exhaust piping system23、汽缸油日用柜 Cylinder oil daily tank 8、日用供水系统 Daily water piping system24、尾管滑油重力柜 Gravity tank of tube oil 9、蒸汽系统 Steam piping system25、排气水封箱 Exhaust seal water tank 10 、锅炉给水和凝水系统 Feed water and condensate of boiler piping system 26、蒸馏水水舱 Distilling water tank 11、燃油净油系统 Fuel oil purified piping system27、污水井 Bilge well 12、燃油输送系统 Fuel oil transport piping system三、各种管系系统 All kinds of pipes33 41舵销 Rudder pintle 13、滑油净油系统 Lubricating oil purified piping system舵杆衬套 rudder stock liner 14、滑油输送系统 Lubricating oil transport piping system舵杆轴套 Sleeve for rudder stock 15、舱底压载系统 Ballast and bilge water piping system舵销承衬套 Bush for rudder pintle 四、仪表类 Instructions舵销轴套 Sleeve for rudder pintle 1、压力表 Pressure gauge上舵承底座 Rudder carrier seat 2、真空表 Vacuum gauge舵销承座 Pintle bearing 3、温度计 Thermometer舵杆承座 Rudder stock bearing 4、吨位表 DWT gauge 挡圈 Retaining ring 5、遥测表 Distant survey gauge舵柄 Tiller 6、液全器 Level switch7）舵角 The angle of rudder5、空压机 Air compressor1）主空压机 Emergency air compressor2）应急空压机42 437、传感器 Sensor 12、机控室 Engine control room五、其它 Others 13、台虎钳 Vise (=vice)1、风机 Fan 14、表铜截止阀 Bronze close valve2、防海生物装置 Anti-foul STM plant 15、表铜截止止回阀 Bronze check valve3、泡沫柜 Air foam tank 16、铸铁截止阀 Cast iron stop valve4、中间轴 Middle shaft 17、铸铁截止止回阀 Cast iron check and stop valve5、尾轴 Propeller shaft 18、调节阀 Adjustable valve6、螺旋桨 Propeller 19、溢流阀、安全阀 Relief valve7、中间轴承 Line shaft bearing 20、减压阀 Reducing valve8、泡沫灭火机 Foam fire extinguisher 六、材料 Material9、饮水消毒装置 Sterilizer plant 1、管子 Pipe10、主配电板 Main switch board 2、无缝钢管 Seamless steel pipe (tube)11、机舱集控台 Engine room control console 3、紫铜管 Purple copper pipe44 454、铁法兰 Iron flange 18、支架（马脚） Clamp5、铜法兰 Copper flange 19、油漆 Paint6、盲板法兰 Blind-flange 20、备件 Spare parts7、螺丝（螺栓） Bolt8、双头螺丝 Stud 七、生产工具 Produce tool9、螺帽（螺母） Nut 1、图纸 Drawing10、不锈钢螺丝 Stainless steel bolt 2、活络钣 Adjustable spanner11、垫片（床） Gasket 3、令司板（梅花钣） Ring spanner12、橡皮床 Gum gasket 4、开口钣 Open –ender spanner13、纸箔床 Paper copper gasket 5、管子钳 Pipe wrench14、紫铜床 Purple copper gasket 6、凿子 Chisel15、石墨床 Black lead gasket 7、锒头 Hammer16、青铅床 Black lead gasket 8、锉刀 File17、佛纳 Feeler gauge 9、螺丝刀 Screwdriver46 4710、油漆滚筒 Paint roller 4、首先请检查安装说明和电气绝缘11、油漆刷子 Paint brush Please check the condition of installation and insulation first12、钢锯 Hacksaw 5、我们准备将油水分离器动转13、套筒扳手 Socket spanner Now we will run the oily-water separator14、手电筒 Torch 6、请检查动转情况15、钻头 driller Please check the running condition八、英语会话 7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好 good morning Now we will do the function test about alarm and safety device2、今天我们准备交验油水分离器 8、设备交接基本结束Today we will test the oily-water separator. Now the test is over 3、请跟我来 9、请部有何修改意见？Please fellow me. Do you have any question ?48 4910、非常感谢 17、这里增加一只落水斗Thanks Add a drain plug here11、再见 18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开 19、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的 20、这个系统非常重要的，一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏 21、请交验收整改意见This flange /connection is linking Please check your remarks 15、这路系统的试验压力是7公斤 22、天太热了，请休息一会The test pressure of the piping system is 7 bar It’s too hot ,please take a rest16、这里请加强 please make a clamp here 23、我负责这项工作 I am in charge of this job。
造船常用船体英语词汇
剖面模数, section modulus, 惯性模量分布, modulus of inertia, 舯横剖面/纵剖面, midship section/lon gitudinal section, 冰区加强, ice strengthening 向下和横贯浸水布置, down-and crossfloding arrangem ents 破舱稳性, damage stability 总纵弯曲, longitudinal bending中拱弯曲, hogging, 中垂弯曲, sagging , 总纵强度, longitudinal strength, 横向强度, transverse streng th, 屈曲强度, buckling strength, 疲劳强度, fatigue strength, 易疲劳区, fatigue prone areas, 局部强度, local stength, 纵骨架式, longitudinal system of frame横骨架式, transverse system of frame, 许用应力, permissible stress, 附加应力, additional stress, 结构节点, structural detail 紧剖面面积, cross sectional area, 旋紧力矩, tightening moment, 砰击压力, sla海洋工程与船舶网--好网站！ing pressure, 拉伸力, tensile force, 加速度分量, acceleration compon ent，弯矩/扭矩/剪力, bending moment/torsional /shear forces 设定压力/设定载荷状态, set pressure/e nvisaged loading condition 端接缝, butt，边接缝, seam横向和纵向构件, transverse and longitudinal girders, 结构件, structural element, 强力构件, strength member ,板架, grillages, 板格, plate field 腹板, doubling plate 部分板架, partial field内部构件, interi or member ,交叉构件, secondary, 主要构件, primary, 特种构件, special，板格, plate panels上下托架, upper (lower)shelt plate, 托架座, stool，下凳式结构, lower stool 泄板和扣板, shedder and gussedplate支承垫板, bearing pads, 支承结构, substructure, 限位器, stopper or stays, 加强筋, stiffners无支承跨距, unsupported span船体, hull or shell , 主船体, main hull, 船体的上缘和下缘, upper and lower hull flange上层建筑, superstructure or erections, 首柱, stern bar , 首柱板, plate stern, 首楼, forecastle, 尾楼, poop , 艉柱, stern post 外板, shell plating, 围壁, house walls 壁板板缝垂直度, verticality of seam of lining plate，外壁, outside wall 护舷材, fender，护舷木、垫板, skid, 舷部护条, side ceiling船尾突出部分, stern counter，船的尖端, beak甲板, deck, 上甲板, upper deck, 下甲板, down deck,中间甲板, tween deck, 露天甲板, weather dec k, 吨位甲板, tonnage deck 蔗蔽甲板, shelter deck,桥楼, navigating bridge, 起居甲板, accoodation deck 艏楼甲板, forecastle deck, 艉楼甲板, poop deck 强力甲板，strength deck ,直升机甲板，helicop ter decks外板外侧与甲板内侧处, on back side of deck plate and out side surface of shell pate甲板板, deck plating, 甲板边板, gunwale strake or deck stinger甲板板条, deck strips强力甲板的甲板边板, stringer plate in strength deck, 圆形船缘、甲板边缘, rounded gunwale甲板支柱, deck pillar, 甲板横梁, deck beam货舱, cargo hold, 舱壁, bulkhead, 中纵舱壁, centrline bulkhead 横舱壁, transverse bulkhead, 制荡舱壁, wash bulkhead 防撞舱壁, collision bulkhead, 槽形舱壁, corrugated bulkhead,槽形舱壁的间距及深度, pitch and depth of swedged corrugated bulkhead分隔舱壁, partition bulkhead, 气密舱壁, airtight bulkhead 水密舱壁, watertight bulkhead 油密舱壁, o iltight bulkhead, 防火舱壁, fireproof bulkhead 水密耐火舱壁, watertight fire-proof bulkhead, 可移动舱壁, shifting bulkhead 防风雨的，不透风雨的, weathertight防火分舱, fire subdivision 水密分舱, watertight subdivision 水密完整性, watertight integrity., 完整稳性, intact stability舷墙, bulwark ,舷墙扶强材, bulwark stay, 列板, strake , 舷侧列板, side strake, 舷顶列板, sheer str ake , 舷侧外板, side plate舭板, bilge plate, 龙骨板, keel plate, 舭龙骨, bilge keel, 中内龙骨, centre keelson船底外板, bottom plating, 内底板, ceiling or tank top or inner bottom plate or double bottom 内底边板, margin plate 内底边板, margin plate舱口围板, hatch coaming, 舱口纵桁, hatch side girder, 舱内纵桁, hold stanchion肘板, bracket, 撑材, struts, 垫货板, dunnage boarch , 梁肘板, beam knee舭肘板, bilge bracket ormargin plate, 防倾肘板, tripping bracket肋板, floor ,实肋板, plate floor, 组合肋板, bracket floor ,水密肋板, watertight floor ,柜架肋板, bracke t floor ,横梁,beam, 舱口端横梁, hatch end beam肋骨，frame，强肋骨, web frame，尾框架，尾肋骨, sternframe 船底肋板, bottom frame内底横骨, reverse frame甲板间肋骨, tweendeck frame, 船底肋骨, bottom frame斜肋骨?, scant fram e, 有曲度肋骨, curved frame 高边柜框架, topside tank webframe 间距, space肋骨间, inter costal 桁材, girder, 旁桁材, side girder, 中桁材, centre girder, 舷侧纵桁, side stringer船体梁, ship girder 中底桁, bottom certre girder 旁底桁, bottom side girder, 甲板纵桁, deck girder水平桁, horizontal girder纵骨,,longitudinal, 船底纵骨, bottom longitudinal, 内底纵骨, inner bottom longitudinal甲板纵骨, deck longitudinal, 舷侧纵骨, side longitudinal折边纵骨及折边撑材, flanged longitudinals and flanged bra cket加强材, reinforcement 加强筋, stiffener, 扶强材的端部削斜, sniped ends of stiffeners, 垂直扶强材, v ertical stiffener支撑间距, stray space 端部连接, end attachment, 刚性固定, constraint , 板边缘固定, plate edge cla mped, 简支, simple support, 支撑桁材, supporting girder, 撑杆, cross tie支柱, pillar隔离空舱, cofferdam, 居住舱室, accoodation, 泵舱, pump room, 机舱, engine room污油水舱, slop tank, 污水舱, sewage tank，液舱限界面, tank boundaries, 货舱, cargo hold, 海阀箱, sea chest，边舱, wing tank，底边仓斜顶板, hopper side plating，顶边仓斜底板, topside tank botto m 双层底舱D.B tank or double bottom tank，空舱, void tank，首尖舱, fore peak tank。
船体结构词汇
Cargo hatch 货舱口 Cargo hose 货油软管 Cargo winch 起货绞车 Cast steel stern post 铸钢wei 柱 Cat walk 步桥 Center girder 中纵椼 Centerline bulkhead 中纵舱壁 Chock 导缆钳 Chain clamp 制链钳
Elcket 延伸肘板
Embarkation deck 登乘甲板 Expansion joint 伸缩接头
Emergency exit 紧急出口
Expansion trunk 膨胀井
End open link 末端链环
Eye plate 眼板
End shackle 末端卸扣
Framing 骨架 Freeboard 干舷 Fresh water tank 淡水舱 Fuel oil tank 燃油舱 Full load 满载 Funnel 烟囱 Gangway 舷梯 Galley （船上）厨房 Gear 小齿轮
Gearwheel 大齿轮
Hand crank 手摇柄
Girder of foundation 基座纵椼
Chain cable fairlead 导链滚轮 Chain cable stopper 制链器 Chain link 锚链环 Chain locker 锚链舱 Chart room 海图室 Clear view screen 旋回视窗 Clutch 离合器 Cofferdam 空隔舱 Collision bulkhead 防撞舱壁
船检英语1
2．数据与资料Data and Information数据总长Length overall(LOA)垂线间长Length bet. perpendiculars (LBP)首、尾垂线Forward and after perpendiculars型宽Moulded breadth型深Moulded depth建造日期Date of build签订建造合同日期Date of building contract龙骨安放日期Date of keel laid交船日期Date of delivery下水日期Launching date重大改建Major conversion安放龙骨或船舶处于相似建造阶段的日期Date on which keel was laid or ship was at a similar stage of construction 签订改建合同日期Date of conversion contract改建完工日期Date of completion of conversion船舶所有人Owner经营人Operator承租人Charterer船舶编号或呼号Distinctive number or letters航行区域Navigation area/Service area/Trade area曾用过的船名Former Name姐妹船Sister Ship总吨位Gross tonnage净吨位Net tonnage排水量Displacement载货量Cargo weight载重量Deadweight空船重量Light(-ship) weight吃水(首、尾、平均) Draft ( fwd, aft, mean)稳性Stability完整稳性Intact stability破舱稳性Damaged stability分舱（抗沉性）Subdivision初稳性高度Metacentric height衡准数Criterion numeral剖面模数Section modulus惯性矩Moment of inertia纵总强度Longitudinal strength局部强度Local strength方形系数Block coefficient静水弯矩Still water bending moment重心垂直高度V ertical height of centre of gravity屈服应力Yield stress标准舷弧Standard sheer防火分隔Fire division航区限制Navigation area restriction海况限制Sea state restriction天气限制Weather restriction最大抗风暴能力Max. weatherliness储备浮力Reserve buoyancy续航力Endurance渗透率Permeability盲区Blind area共振区域Resonance region容许载荷Permissible load核定载客数Number of persons certified to carry干舷：Freeboard热带干舷Tropical freeboard夏季干舷Summer freeboard冬季干舷Winter freeboard北大西洋冬季干舷Winter North Atlantic freeboard热带木材干舷Timber tropical夏季木材干舷Timber summer冬季木材干舷Timber winter北大西洋冬季木材干舷Timber winter North Atlantic freeboard 淡水宽限Allowance for fresh water减少干舷的B型船舶Type B with reduced freeboard增加干舷的B型船舶Type B with increased freeboard载重线：Load line载重线标志Loadline marks（二）缺陷与损坏的类别与原因缺陷defects, deficiencies制造中缺陷defects in(during) manufacturing潜在缺陷latent (potential 可能的) defects金属分层lamination金属疲劳fatigue金属疏松porosity如：汽缸套内表面发现金属疏松。
船舶检验英语
一、船头bit 系缆桩bollard 系缆桩bow 船首bow fender 艏护垫bow flare 艏部外飘bow thruster艏侧推器bow anchor 艏锚bow frame 舟包部肋骨bow chock艏导缆口bow stopper制链器break water 挡浪板bulbous bow球鼻艏bulb stem 球式艏柱cable stopper制链器chain locker 锚链舱chain pipe锚链管chain stopper止链器chock 导缆器clamp plate夹板垫木cleat羊角系绳铁栓防滑条capstan绞盘capstan绞盘筒collision bulkhead 防撞舱壁forecastle首楼forecastle deck 首楼甲板fore peak tank首尖舱foundation 底座ground tackle 锚泊索具gypsy绞筒（锚机绞车上的）hawse pipe锚链筒hawse hole锚链孔hawser大缆hawser clamp锚链挚hawse buckler/flap锚链孔盖mooring post 系缆柱mooring hole导缆孔astern post尾柱warping chocks滚轮导缆钳winch-head 绞车卷筒windlass起锚机wire clip钢缆夹wire reel 卷缆车钢丝滚筒flush deck 平甲板gunwale圆弧过渡舷边adapting连接管管接头air hole空气管air pipe通风管air funnel货舱通风筒air and sounding pipe amidships船中部appendages船体附属体（包括舵机和螺旋桨等）base line基线Batten板条压条batten cleat舱口契耳batten down封舱batten seat板条坐架压条架batten wedge封舱契batten ceiling（货舱内）护舱条护板batten bar舱围压条beam bracket/knee 梁肘板bevel斜角斜面bevel angle斜角坡口角度bevel board斜角板bevel edge斜边bevel face斜面bevel frame斜边肋骨bilge舟比部bilge bracket舟比肘板bilge knee舟比肘板bilge keel(chock piece)舟比龙骨bilge line 污水管道bilge pipe 污水管bilge pump污水泵bilge well/sump污水井bilge alarm system污水警报系统bilge tank污水舱bilge discharging pipe 污水排放管boom吊杆bilge inlet 污水收集口bilge keelson舟比龙骨bilge plug 污水塞bilge sounding pipe污水测深管bottom frame 底部肋骨bottom longitudinal底部纵桁bottom plating 舱底板bridge驾驶台cat walk bridge 纵向天桥，步桥catwalk catway纵向天桥，步桥bridge fittings桥式连接器（集装箱桥锁）bridge wing 驾驶台两翼bridge space 驾驶台bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener舱壁扶强板bulwark舷墙bulwark brace舷墙斜撑bulwark plating 舷墙板bulwark stay舷墙扶强材bulwark freeing port舷墙排水口camber of a ship中拱hogging 中拱sagging中垂camber of beam拱梁cant frame斜梁cant bracket 斜角板cant frame斜肋cantilever悬臂梁cantilever beam悬梁cargo batten 货舱护板cargo block吊货滑车cargo port装货舷门centerline中心线center girder center strake中央内底板chafing plate防擦板chafing ring 防擦环collar plate封板corrugated bulkhead槽型舱壁corrugation槽型的crossing deck structure交叉甲板结构crossing strength member 交叉强力结构cofferdam隔离舱cutout 开口davit吊艇架deck 甲板deck beam甲板横梁deckhouse甲板屋deck line甲板线deck longitudinal甲板纵桁deck plate甲板边板deck tank 甲板上的舱derrick吊杆designed waterline length 设计水线长designed waterline breadth设计水线宽doubling plate 双层焊合板drain hole排水孔duct keel箱型龙骨dunnage 垫舱dunnage wood 垫木dynamic load动载荷diaphragm plate 隔板expansion trunk(油船)膨胀深井extension bracket 延伸肘板extreme breadth最大宽度face plate 表层板fender靠垫fender bar护舷条flame screen防焰罩flange折边flange bracket折边肘板flat keel平板龙骨floor肋板folding door折门flame space肋（骨间）距flame number肋骨号freeing port甲板排水孔gasket 垫圈垫料handrail 舷墙扶手goose neck 鹅颈头吊杠弯头gunwale舷缘舷边gunwale angle舷边角钢gunwale bar舷边角材gunwale railing 舷边栏杆gunwale tank舷侧水柜gusset 角板扣板gutter（甲板）水沟槽沟gutter angle waterway angle（舷侧）排水沟角钢hanging rudder 密封条hatchway 舱口槽hatch opening 舱口hatch bar封舱压条hatch batten舱口边压条hatch beam(web)舱口大梁hatch booby活动舱口盖hatch coaming舱口围板hatch cover 舱口盖hatch end beam舱口端梁hatch side girder hatch tarpaulin舱口帆布盖hatch trunk舱口围井hand nut蝴蝶螺母hinged cover(door)铰链盖hold货舱hold beam舱口横梁hold frame舱内肋骨hold ladder 货舱梯hold stanchion(pillar)舱内支柱Hopper hopper tankHopper tank sloping plating horizontal girderhorizontal margin plate 水平内底板horizontal stiffener水平扶强材hull船体hull construction船体结构hull plating 船体板hull strength船体强度inner bottom 内底板inner bottom plating内底板insert plate嵌板衬板intersection交点交叉横断面jack 千斤顶jack ladder绳梯rJacob’s ladder软梯绳梯joggled joint折接弯合joggled machine折曲机keel龙骨keelblock龙骨墩keel line龙骨线keel plate 龙骨板keel rail（救生艇）艇底把手keelson龙骨板kingpost起重柱将军柱knee肘板knee of the deck甲板梁肘板knee pipe 弯管knee plate肘板knukle折角线lighting hole减轻孔local strength局部强度local stress局部应力longitudinal bulkhead纵舱壁longitudinal纵骨longitudinal bending纵向弯曲longitudinal frame system纵骨架式longitudinal strength总纵强度lug耳板main deck 主甲板main frame主肋骨manhole 人孔manhole door人孔门man hole coaming 人孔围板margin plate内底边板molded breadth型宽molded depth型深non-watertight bulkhead非防水舱壁notch切口oscillating load震动负荷parallel middle body平行舯体panel stiffener板格扶强材panting arrangement防桡震结构panting beam防桡震梁panting stringer防桡震纵材pillar 支柱/墩plane bulkhead舱壁板plane keel 龙骨板pump room泵间horizontal margin plate水平内底边板 out bottom platingplatform 平台plating外板racking(船体)横向扭变rail栏杆register length(breadth depth) rise of floor(dead rise)船底斜高rolling横摇round of beam拱梁rung(梯子)踏步,横挡scallop 扇形开口scantling构件尺寸scantling of the structure结构尺寸scarf/scarph嵌接处scarf joint斜(嵌)接scarf weld(斜面)焊接scarf bracket铅接肘板scupper排水孔scupper pipe排水管section剖面section modulus剖面模数shedder plate斜板,泄板sheer舷弧forward(after)perpendicular首尾舷弧 sheer line舷弧线sheer strake 舷顶列板shell船壳shell plating船壳板shelter deck遮蔽甲板shifting beam移动舱口梁shifting board(plank)止移板side longitudinal边纵桁single bottom 单层底side plating边板skid护舷木slanting plate斜板sloping plate斜板sloping plate longitudinal 油水舱纵向板slot槽,开缝sluice水(密)门,水闸sluice valve闸阀sniped end消斜端soft toe软趾solid floor实肋板sounding pipe 测深管stabilizer stabilizing tankstaging 架构,台架,手脚架stanchion支柱,栏杆柱stay 支柱,撑条,支索stay bar撑杆stay plate 撑板strength deck加强甲板stringer plate甲板边板structure member构件structure strength结构强度strumbox(舱底水)过滤箱strut 撑材stuffing box填料箱tarpaulin 帆布tieplate带板,牵板,连接板topside tank顶边水舱torsion 扭转torsion strength扭转强度vertical ballast trunk 竖向压载通道transverse横梁,横材transverse bulkhead横向舱壁transverse frame横梁transverse framing system横骨架式transverse ring 横梁令环transverse strength横向强度tripping bracket防倾肘板tween deck二层甲板tween deck frame二层甲板肋骨twisting distortion扭转变形upper deck上甲板upper(lower)shelf plate上(下)支架板upper(lower)stool 上(下)托架ventilator通风管wash bulkhead制荡舱壁plimsoll line载重线watertight bulkhead 水密舱壁watertight door 水密门web frame 加强肋骨web plate复板wedge 契子winch起货机wing tank 翼舱,翼柜ballasting pump system 压载水泵系统aft draft 尾吃水ballast压载水ballast line压载线ballast pump压载泵draft figures 吃水尺度even keel平吃水,平载floodable length 可浸长度fresh water loadline淡水载重线fresh water timber load line 淡水木材载重线length between perpendicular首尾间柱长ballast tank压载舱length overall 总长loadline mark载重线标识freeboard mark 载重线标识freeboard assignment干舷划定freeboard deck 干舷甲板freeboard depth 干舷深度freeboard zone 干舷区plimsoll mark载重线标记plimsoll disc/loadline disc载重线标圈load waterline length满载水线长moment of inertia惯性矩static load 静负荷strength calculation强度计算summer loadline夏季载重线summer fresh water loadlin夏季淡水载重线e tropical fresh water loadline热带淡水载重线tropical loadline热带载重线twisting moment 扭矩winter load line冬季载重线winter North Atlantic load line北大西洋冬季载重线bunker tank 燃油舱bushing 衬套butt 端接butt joint /seam平接缝but riveting 对接铆butt welding对接焊butterfly clip 蝴蝶夹bypass valve旁通阀sheer strake列板gunwale船舷上缘main frame主肋骨side longitudinal边纵tweendeck frame二层甲板肋骨i ntermediate frame内中肋骨web frame强肋骨hatch coaming/hatch side coaming舱口围板side shell longitudinal 船壳纵向边板side shell plating船壳边板fire hydrant消防水龙hose 软管nozzle喷头fire extinguisher灭火器portable foam applicator unit移动泡沫枪单元quick closing valve 速闭阀remote control shut off遥控关闭funnel skylight 烟囱天窗shutter ventilator通风管道关闭器fire damper防火盖properly closed 正常关闭reset重起ventilator通风管duct 管道high pressure fuel pump高压燃油泵fuel injector 油泵喷口jacked pipe管路套high pressure fuel deliver line输送管道external外部的outside diameter外径flange法兰washer垫圈boats 螺栓nuts螺母dimension 尺寸gasket垫片fixed gas fire-extinguishing system.固定灭火系统fixed high expansion foam fire-extinguishing system固定高效泡沫灭火系统fixed pressure water-spraying fire-extinguishing system固定高压水雾灭火系统storage room储藏间fire extinguishing medium灭火介质protected area 保护区域water/ spray nozzle水/雾两用喷头monitor泡沫炮pressure gauge压力表fixed detection and fire alarm固定灭火探测警报automatic sprinkler 自动喷淋Spare parts备件sample extraction smoke detection system烟雾探头manually operated call points人工操纵报警点smoke detector/thermal detector烟雾/热能探头audible and visual alarm音响和视觉警报operational readiness操作说明maintenance plan保养计划training manual训练手册fire safety operational booklet(fob)消防手册emergency fire pump 应急消防泵portable emergency fire pump移动应急消防泵diesel engine柴油机vacuum pump真空泵containment of fire functional requirements要求功能method 1C 1C形式control station集中控制站corridor 走廊stair way楼梯low risk service space 低风险服务区blower鼓scrubber 洗涤塔deck seal甲板水封inert gas deck main惰性气体甲板主管oxygen氧气nitrogen氮气inert gas generator惰性气体发生器manually operated valve人工操纵发7 no-return valve 止回阀wing tank翼舱center tank 中间舱slop tank污油水舱main panel 主面板sub panel幅面板sea chest/valve 海水箱/阀hydrocarbon gas碳氢化合物pressure/vacuum breake压力/真空保护装置accommodation space 住宿区“A” class division“Ａ”级隔离central control station 中央控制台fire door防火门fire safety system code防火安全程序代码fire test procedure code 防火试验程序代码machinery space 机器处所main vertical zone主竖区oil fuel unit 燃油单位public space公共区service space服务区machinery space of category AＡ级机器处所other machinery space其他机器处所cargo space货物间high risk service space高风险作业区open deck开敞甲板weather deck风雨密甲板ro-ro and vehicle space滚装船车辆处所openings开口fire resisting division 防火分隔coming围板fire integrity of bulkheads separating横舱壁分隔防火完整性adjacent spaces附近区域fire integrity of decks separating甲板分隔防火完整性。
船舶专业英语词汇(初级)
船舶专业英语词汇（初级）1．基本，简单的词汇：AM 上午 PM下午Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师2、船体总体，及各类型船舶Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船Naval Ship/war shipd 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assrsted vessel 地效船3、各专业基本词汇1）船体：Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under out 咬口Sharp edge 快口•作者：pzfhubert••2007-8-28 22:21•回复此发言2 船舶专业英语词汇（初级）Deflection 挠曲，变形Slags 渣Welding slags 电焊渣Automatic welding 自动焊Manual welding 手工焊Arc welding 电弧焊Gas shielded welding气体保护焊Inter gas arc welding惰性气体保护电弧焊Welding seam焊缝Bending machine 弯曲机Three-roll bending machine三芯弯板机Torsional box抗扭箱Void space空舱Cofferdam 隔离舱Bulwark舷墙，防浪板Wall墙壁Floor地板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vapour return line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Room房间Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）3）电器Current电流Voltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Wire 电线Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹Voltage drop 电压降Speed droop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值重载询问test the power surplus setting point重载询问试验4）漆、木Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Lingt blasting 预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solvent使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Wearing coat 磨耗层Zinc-rich coating富锌涂层Cement wash coating（薄）水泥涂层Stripe coating 预涂层Floor covering 地板覆层Alkyd resin paint醇酸树脂漆Epoxy(resin-based)paint环氧树脂涂料•作者：pzfhubert••2007-8-28 22:21•回复此发言3 船舶专业英语词汇（初级）Scuttle舷窗Carpet地毯Wooden skirt木裙板（踢脚）Aluminum skirt稆质裙板（踢脚）Brass nose装于楼梯踏步一的黄铜防滑镶条Stainless screw不锈钢螺钉Spring 弹簧Securing dev ice固定件Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔CureCuring硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Pheomatic tools风动工具Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronize motor同步电机synchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时carrier载波，载波电流transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pluse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Shisel凿子Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Dafety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Pilot ladder引水员；软梯•作者：pzfhubert••2007-8-28 22:21•回复此发言4 船舶专业英语词汇（初级）2)轮机Centering对中心Alignment对准，对准中心Inspection报验Installation安装Final inspection of M/E insallation主机最终安装报验Inspection of the centering of the stern tabe before fine boring精镗前艉轴管中心校准Alignment check/inspection拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system燃油管串油后清洁检查Function test of steering gear舵机效甩试验Hose test of water tight doors水密门冲水试验Noise lever measurement噪声测量Vibration level measurement 振动测量Main engine (M/E)主机Generator发电机Emergency generator应急发电机Shaft generator轴带发电机Fresh water generator 制淡装置Steering gear 舵机General service pump总用泵Pire pump消防泵Hydraulic motor 液压马达Hydraulic nuts液压螺帽Rudder舵Rudder bl ade舵叶Propeller车叶，螺旋桨Fixed pitch propeller固定螺距的螺旋桨Lofting型线图放样Lay off（船及部件）放样，下料Plate-cutting钢板下料，开工Numerically-controlled cutting machine数控切割机Cutting machine切割机Under water plasma cutting machine水下等离子切割机Surface preparation表面处理Fabrication（焊）开坡口，边缘加工（如刨边）Upside down construction method分段装配Assembly 反身建法Erection装配，大合拢Jig装配架，胎架Bow jip 船首部胎架Girder纵向构件，桁（材）Beam梁，横梁Sections型材Profile型钢（条）Bar 杆，棒,棒材Plate板材Angle bar角钢I beam（窄缘）工字梁H beam（宽缘）工字梁Stiffener扶强材Bracket托架，支架，肘板Support 支架Frame肋骨，框架Douler复板Coaming（舱口）围板，缘材Sinp剪切Cut切割Anchor锚Anchor widdlass 锚机Anchorage锚位，锚地Chain链Chain block链条滑车，神仙滑车Platform平台Crossover跨越（梯桥），立交Life raft 救身筏Life buoy 救生圈Forward winch 前绞缆机After winch 后绞缆机Windlass锚机Bitt带缆桩，系桩Fairlead导缆钳，导缆孔Hand rail扶手，栏杆Beam横梁Frame肋骨，框架Scantling构件尺寸Cargo oil tank货油舱Scantling draft结构吃水Forepeak tank首尖舱After peak tank尾尖舱Water ballast tanks(W.B.T)压载水舱Fuel oil tank(F.O.T)燃油舱Lubricating oil tank(L.OT)滑油舱Diesel oil tank(D.O.T)柴油舱Double botton双层底Double skin双层外板，双层蒙皮Bow thruster艏侧推Propeller车叶Fixed pitch propeller定螺距螺旋桨Controllable pitch propeller(CPP)可调螺距螺旋桨Shaft轴Tail shart尾轴Shaft generator轴带发电机Watertight doors水密门Bulwark舷墙Bulkhead舱壁Tank top内底，液舱顶Hatch cover舱口盖Manhole人孔Fin stablizer减摇鳍Antifouling system防海生物的，防污染系统Ship船Vessel船，舰Fabrication制造，分段装配（precfabrication预制，预加工）Assemble装配，组装Erection大合拢，船台装配Staging脚手架Block stage分段阶段Mile stone（里程碑，大节点）Plate-cutting下料，开工Keel-laying上船台，龙骨铺设Lauching下水mooring trial码头试验，系泊试验sea trial(sea)试航delivery of the ship交船defect list by the owner/society船东提出的消除意见清单/船级社提出的消除意见清单design stage设计阶段submit drawings to owner,classification society(LR、DNV、BV、ABS，etc)for approval向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸hull workshop船体车间machining workshop金工车间machinery engineering workshop轮机车间electrical workshop电气车间business dept.经营处perchasing dept.供应处Q.C.Dept.检验处Design dept.设计室Painting and carpenter’s workshop漆木车间Project manager项目经理Director指导者，厂长，董事Managing director执行董事，常务董事，总经理Head首长，团长，主任Manager经理，管理人，干事Leader领导者Meeting会议Negotiation谈判Agreement协议Shipyard船厂。
船体单词表1
船体单词表总纵弯曲____________ 总纵强度____________船梁____________ 横向强度____________局部强度____________ 纵骨构式____________外板____________ 横骨构式____________端接缝____________ 边接缝____________船底板____________ 平板龙骨____________舭列板____________ 舷侧外板____________舷顶列板____________ 复板____________锚穴____________ 并板____________ 外板展开____________ 舷弧____________ 梁拱____________ 上甲板____________下甲板____________ 舷伸甲板____________强力甲板____________ 露天甲板____________舷边角钢____________ 圆弧舷板____________单底____________ 双层底____________ 中内龙骨____________ 旁内龙骨____________ 肋板____________ 折边____________ 舭肘板____________ 球扁钢____________ 中底桁____________ 旁底桁____________人孔____________ 减轻孔____________主肋板____________ 水密肋板____________ 框架肋板____________ 透气孔____________通焊孔____________ 加强筋____________削斜____________ 内底横骨____________ 船底肋骨____________ 肘板____________角钢____________ 内底板____________内底边板____________ 污水井____________纵骨____________ 隔离空舱____________ 防倾肘板____________ 底边舱____________分节驳____________ 肋骨____________主肋骨____________ 甲板间肋骨____________ 强肋骨____________ 中间肋骨____________ 舷侧纵桁____________ 撑杆____________ 压载水舱____________ 舷边舱____________抗扭箱____________ 甲板骨架____________ 横梁____________ 半梁____________ 舱口端横梁____________ 甲板纵桁____________ 舱口纵桁____________ 梁肘板____________甲板纵骨____________ 货舱口____________ 舱口围板____________ 菱形板____________ 悬臂梁____________ 支柱____________ 出入舱口____________ 膨胀井____________顶边舱____________ 舱壁____________ 水密舱壁____________ 纵舱壁____________ 横舱壁____________ 防撞舱壁____________ 舱壁甲板____________ 艉尖舱舱壁____________ 艉轴管____________ 舵杆围井____________中纵舱壁____________ 平面舱壁____________ 舱壁板____________ 垂直扶强材____________ 水平桁____________ 水平扶强材____________竖桁____________ 槽型舱壁____________轻舱壁____________ 压筋板____________直立型首____________ 前倾型首____________飞剪型首____________ 破冰型首____________球鼻型首____________ 椭圆型尾____________ 巡洋舰型尾____________ 首尖舱____________ 升高肋板____________ 止荡舱壁____________ 锚链舱____________ 尾尖舱____________ 侧推器____________ 尾封板____________ 首柱____________ 尾柱____________ 舵柱____________ 螺旋桨柱____________ 轴毂____________ 舵轴架____________ 尾轴架____________ 轴包套____________ 上层建筑____________ 甲板室____________首楼____________ 尾楼____________ 桥楼____________ 机舱棚____________ 机座____________ 锅炉机座____________舷墙____________ 护舷材____________ 舭龙骨____________。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
一、船头bit 系缆桩bollard 系缆桩bow 船首bow fender 艏护垫bow flare 艏部外飘bow thruster艏侧推器bow anchor 艏锚bow frame 舟包部肋骨bow chock艏导缆口bow stopper制链器break water 挡浪板bulbous bow球鼻艏bulb stem 球式艏柱cable stopper制链器chain locker 锚链舱chain pipe锚链管chain stopper止链器chock 导缆器clamp plate夹板垫木cleat羊角系绳铁栓防滑条capstan绞盘capstan绞盘筒collision bulkhead 防撞舱壁forecastle首楼forecastle deck 首楼甲板fore peak tank首尖舱foundation 底座ground tackle 锚泊索具gypsy绞筒（锚机绞车上的）hawse pipe锚链筒hawse hole锚链孔hawser大缆hawser clamp锚链挚hawse buckler/flap锚链孔盖mooring post 系缆柱mooring hole导缆孔astern post尾柱warping chocks滚轮导缆钳winch-head 绞车卷筒windlass起锚机wire clip钢缆夹wire reel 卷缆车钢丝滚筒flush deck 平甲板gunwale圆弧过渡舷边adapting连接管管接头air hole空气管air pipe通风管air funnel货舱通风筒air and sounding pipe amidships船中部appendages船体附属体（包括舵机和螺旋桨等）base line基线Batten板条压条batten cleat舱口契耳batten down封舱batten seat板条坐架压条架batten wedge封舱契batten ceiling（货舱内）护舱条护板batten bar舱围压条beam bracket/knee 梁肘板bevel斜角斜面bevel angle斜角坡口角度bevel board斜角板bevel edge斜边bevel face斜面bevel frame斜边肋骨bilge舟比部bilge bracket舟比肘板bilge knee舟比肘板bilge keel(chock piece)舟比龙骨bilge line 污水管道bilge pipe 污水管bilge pump污水泵bilge well/sump污水井bilge alarm system污水警报系统bilge tank污水舱bilge discharging pipe 污水排放管boom吊杆bilge inlet 污水收集口bilge keelson舟比龙骨bilge plug 污水塞bilge sounding pipe污水测深管bottom frame 底部肋骨bottom longitudinal底部纵桁bottom plating 舱底板bridge驾驶台cat walk bridge 纵向天桥，步桥catwalk catway纵向天桥，步桥bridge fittings桥式连接器（集装箱桥锁）bridge wing 驾驶台两翼bridge space 驾驶台bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener舱壁扶强板bulwark舷墙bulwark brace舷墙斜撑bulwark plating 舷墙板bulwark stay舷墙扶强材bulwark freeing port舷墙排水口camber of a ship中拱hogging 中拱sagging中垂camber of beam拱梁cant frame斜梁cant bracket 斜角板cant frame斜肋cantilever悬臂梁cantilever beam悬梁cargo batten 货舱护板cargo block吊货滑车cargo port装货舷门centerline中心线center girder center strake中央内底板chafing plate防擦板chafing ring 防擦环collar plate封板corrugated bulkhead槽型舱壁corrugation槽型的crossing deck structure交叉甲板结构crossing strength member 交叉强力结构cofferdam隔离舱cutout 开口davit吊艇架deck 甲板deck beam甲板横梁deckhouse甲板屋deck line甲板线deck longitudinal甲板纵桁deck plate甲板边板deck tank 甲板上的舱derrick吊杆designed waterline length 设计水线长designed waterline breadth设计水线宽doubling plate 双层焊合板drain hole排水孔duct keel箱型龙骨dunnage 垫舱dunnage wood 垫木dynamic load动载荷diaphragm plate 隔板expansion trunk(油船)膨胀深井extension bracket 延伸肘板extreme breadth最大宽度face plate 表层板fender靠垫fender bar护舷条flame screen防焰罩flange折边flange bracket折边肘板flat keel平板龙骨floor肋板folding door折门flame space肋（骨间）距flame number肋骨号freeing port甲板排水孔gasket 垫圈垫料handrail 舷墙扶手goose neck 鹅颈头吊杠弯头gunwale舷缘舷边gunwale angle舷边角钢gunwale bar舷边角材gunwale railing 舷边栏杆gunwale tank舷侧水柜gusset 角板扣板gutter（甲板）水沟槽沟gutter angle waterway angle（舷侧）排水沟角钢hanging rudder 密封条hatchway 舱口槽hatch opening 舱口hatch bar封舱压条hatch batten舱口边压条hatch beam(web)舱口大梁hatch booby活动舱口盖hatch coaming舱口围板hatch cover 舱口盖hatch end beam舱口端梁hatch side girder hatch tarpaulin舱口帆布盖hatch trunk舱口围井hand nut蝴蝶螺母hinged cover(door)铰链盖hold货舱hold beam舱口横梁hold frame舱内肋骨hold ladder 货舱梯hold stanchion(pillar)舱内支柱Hopper hopper tankHopper tank sloping plating horizontal girderhorizontal margin plate 水平内底板horizontal stiffener水平扶强材hull船体hull construction船体结构hull plating 船体板hull strength船体强度inner bottom 内底板inner bottom plating内底板insert plate嵌板衬板intersection交点交叉横断面jack 千斤顶jack ladder绳梯rJacob’s ladder软梯绳梯joggled joint折接弯合joggled machine折曲机keel龙骨keelblock龙骨墩keel line龙骨线keel plate 龙骨板keel rail（救生艇）艇底把手keelson龙骨板kingpost起重柱将军柱knee肘板knee of the deck甲板梁肘板knee pipe 弯管knee plate肘板knukle折角线lighting hole减轻孔local strength局部强度local stress局部应力longitudinal bulkhead纵舱壁longitudinal纵骨longitudinal bending纵向弯曲longitudinal frame system纵骨架式longitudinal strength总纵强度lug耳板main deck 主甲板main frame主肋骨manhole 人孔manhole door人孔门man hole coaming 人孔围板margin plate内底边板molded breadth型宽molded depth型深non-watertight bulkhead非防水舱壁notch切口oscillating load震动负荷parallel middle body平行舯体panel stiffener板格扶强材panting arrangement防桡震结构panting beam防桡震梁panting stringer防桡震纵材pillar 支柱/墩plane bulkhead舱壁板plane keel 龙骨板pump room泵间horizontal margin plate水平内底边板 out bottom platingplatform 平台plating外板racking(船体)横向扭变rail栏杆register length(breadth depth) rise of floor(dead rise)船底斜高rolling横摇round of beam拱梁rung(梯子)踏步,横挡scallop 扇形开口scantling构件尺寸scantling of the structure结构尺寸scarf/scarph嵌接处scarf joint斜(嵌)接scarf weld(斜面)焊接scarf bracket铅接肘板scupper排水孔scupper pipe排水管section剖面section modulus剖面模数shedder plate斜板,泄板sheer舷弧forward(after)perpendicular首尾舷弧 sheer line舷弧线sheer strake 舷顶列板shell船壳shell plating船壳板shelter deck遮蔽甲板shifting beam移动舱口梁shifting board(plank)止移板side longitudinal边纵桁single bottom 单层底side plating边板skid护舷木slanting plate斜板sloping plate斜板sloping plate longitudinal 油水舱纵向板slot槽,开缝sluice水(密)门,水闸sluice valve闸阀sniped end消斜端soft toe软趾solid floor实肋板sounding pipe 测深管stabilizer stabilizing tankstaging 架构,台架,手脚架stanchion支柱,栏杆柱stay 支柱,撑条,支索stay bar撑杆stay plate 撑板strength deck加强甲板stringer plate甲板边板structure member构件structure strength结构强度strumbox(舱底水)过滤箱strut 撑材stuffing box填料箱tarpaulin 帆布tieplate带板,牵板,连接板topside tank顶边水舱torsion 扭转torsion strength扭转强度vertical ballast trunk 竖向压载通道transverse横梁,横材transverse bulkhead横向舱壁transverse frame横梁transverse framing system横骨架式transverse ring 横梁令环transverse strength横向强度tripping bracket防倾肘板tween deck二层甲板tween deck frame二层甲板肋骨twisting distortion扭转变形upper deck上甲板upper(lower)shelf plate上(下)支架板upper(lower)stool 上(下)托架ventilator通风管wash bulkhead制荡舱壁plimsoll line载重线watertight bulkhead 水密舱壁watertight door 水密门web frame 加强肋骨web plate复板wedge 契子winch起货机wing tank 翼舱,翼柜ballasting pump system 压载水泵系统aft draft 尾吃水ballast压载水ballast line压载线ballast pump压载泵draft figures 吃水尺度even keel平吃水,平载floodable length 可浸长度fresh water loadline淡水载重线fresh water timber load line 淡水木材载重线length between perpendicular首尾间柱长ballast tank压载舱length overall 总长loadline mark载重线标识freeboard mark 载重线标识freeboard assignment干舷划定freeboard deck 干舷甲板freeboard depth 干舷深度freeboard zone 干舷区plimsoll mark载重线标记plimsoll disc/loadline disc载重线标圈load waterline length满载水线长moment of inertia惯性矩static load 静负荷strength calculation强度计算summer loadline夏季载重线summer fresh water loadlin夏季淡水载重线e tropical fresh water loadline热带淡水载重线tropical loadline热带载重线twisting moment 扭矩winter load line冬季载重线winter North Atlantic load line北大西洋冬季载重线bunker tank 燃油舱bushing 衬套butt 端接butt joint /seam平接缝but riveting 对接铆butt welding对接焊butterfly clip 蝴蝶夹bypass valve旁通阀sheer strake列板gunwale船舷上缘main frame主肋骨side longitudinal边纵tweendeck frame二层甲板肋骨i ntermediate frame内中肋骨web frame强肋骨hatch coaming/hatch side coaming舱口围板side shell longitudinal 船壳纵向边板side shell plating船壳边板fire hydrant消防水龙hose 软管nozzle喷头fire extinguisher灭火器portable foam applicator unit移动泡沫枪单元quick closing valve 速闭阀remote control shut off遥控关闭funnel skylight 烟囱天窗shutter ventilator通风管道关闭器fire damper防火盖properly closed 正常关闭reset重起ventilator通风管duct 管道high pressure fuel pump高压燃油泵fuel injector 油泵喷口jacked pipe管路套high pressure fuel deliver line输送管道external外部的outside diameter外径flange法兰washer垫圈boats 螺栓nuts螺母dimension 尺寸gasket垫片fixed gas fire-extinguishing system.固定灭火系统fixed high expansion foam fire-extinguishing system固定高效泡沫灭火系统fixed pressure water-spraying fire-extinguishing system固定高压水雾灭火系统storage room储藏间fire extinguishing medium灭火介质protected area 保护区域water/ spray nozzle水/雾两用喷头monitor泡沫炮pressure gauge压力表fixed detection and fire alarm固定灭火探测警报automatic sprinkler 自动喷淋Spare parts备件sample extraction smoke detection system烟雾探头manually operated call points人工操纵报警点smoke detector/thermal detector烟雾/热能探头audible and visual alarm音响和视觉警报operational readiness操作说明maintenance plan保养计划training manual训练手册fire safety operational booklet(fob)消防手册emergency fire pump 应急消防泵portable emergency fire pump移动应急消防泵diesel engine柴油机vacuum pump真空泵containment of fire functional requirements要求功能method 1C 1C形式control station集中控制站corridor 走廊stair way楼梯low risk service space 低风险服务区blower鼓scrubber 洗涤塔deck seal甲板水封inert gas deck main惰性气体甲板主管oxygen氧气nitrogen氮气inert gas generator惰性气体发生器manually operated valve人工操纵发7 no-return valve 止回阀wing tank翼舱center tank 中间舱slop tank污油水舱main panel 主面板sub panel幅面板sea chest/valve 海水箱/阀hydrocarbon gas碳氢化合物pressure/vacuum breake压力/真空保护装置accommodation space 住宿区“A” class division“Ａ”级隔离central control station 中央控制台fire door防火门fire safety system code防火安全程序代码fire test procedure code 防火试验程序代码machinery space 机器处所main vertical zone主竖区oil fuel unit 燃油单位public space公共区service space服务区machinery space of category AＡ级机器处所other machinery space其他机器处所cargo space货物间high risk service space高风险作业区open deck开敞甲板weather deck风雨密甲板ro-ro and vehicle space滚装船车辆处所openings开口fire resisting division 防火分隔coming围板fire integrity of bulkheads separating横舱壁分隔防火完整性adjacent spaces附近区域fire integrity of decks separating甲板分隔防火完整性。