珠光砂MATERIALSAFETYDATASHEETEXPANDEDPERLITEPROUCTS
珠光砂技术规格书
空分冷箱珠光砂技术规格书1.总则1.1本技术协议适用于空分装置冷箱内保冷用珠光砂生产、供货、加工、充填的技术要求。
1.2本技术协议作为合同的有效组成部分，与合同具有同等法律效力。
合同的解释顺序为合同书、技术协议、招标书、询标时质疑的答复、投标书。
1.3本技术协议提出的是最低限度的技术要求，并未规定所有的技术要求和适用的标准，卖方提供满足本技术协议和所列标准要求的高质量产品及其相应服务。
对国家有关安全、环保等强制性标准，满足其要求。
1.4卖方提供的设备完全符合本技术协议和标准的要求。
1.5卖方执行本技术协议所列标准。
有矛盾时，按较高标准执行。
卖方在设备设计和制造中所涉及的各项规程、规范和标准必须遵循现行最新版本的标准。
1.6卖方提供高质量的珠光砂材料，这些材料应是成熟可靠、技术先进的产品，且生产厂已有相同材料的生产、运行两年以上的成功经验，且实践已证明产品是成熟可靠的。
1.8在签订合同之后，买方有权提出因规范标准和规程发生变化而产生的一些补充要求，具体项目由买卖双方共同商定。
2．珠光砂性能指标：2.1物理特征：2.2 化学性能：2.3 材料性能：松散密度：35 ~ 55 Kg/m3振实密度：48 ~ 65 Kg/m3含水率：≤0.3 % （重量比）有机物含量：≤0.1 %平均热导率：≤0.022 w/mk（常压、77 ~ 293 K）粒度级配：3．珠光砂供货及装填3.1空分装置，由杭州杭氧股份有限公司成套设计并供货，三套空分冷箱装填总量约为41000m³，具体装填量工程竣工时确定，投标方负责第一次装填完毕，以及设备启动运行1～3个月后的补充装填工作。
3.2 空分冷箱内珠光砂由投标方生产并装填。
如用散料，与装填有关的所有吊装用具、人员等。
若采取现场发泡，业主提供水电方便，但所发生水电费用及其他用具、材料、人员等由投标方自理；3.3 投标方在珠光砂装填时必须保证装填质量，阴雨天气不能装填，分层装填，装填后安息角33-37°；3.4珠光砂装填时需要做好对冷箱内外部设备、管道、仪表等的保护，若因装填对设备造成损坏的，由投标方负全责3.5单套空分冷箱装填时间在10天之内4．包装、运输、保管、标记4.1包装及运输必须注意牢固及防潮4.2产品应附有出厂证明，包括下列内容：1）生产厂名和地址；2）产品全称、生产日期；3）出厂编号和产品规格；4）检验合格印章及质量合格证；5）运输保管和注意事项4．3运输保管1）珠光砂产品及装填过程中不得混入杂质；2）产品堆放及运输，必须注意防水、防潮、切勿人踏、物压5.供货5.1供货及安装地点：项目工地；5.2安装时间：第一套冷箱2009年10月，其它两套依次推迟一个月（具体时间以冷箱裸冷完毕为准）。
3M MATERIAL SAFETY DATA SHEET
Material Safety Data SheetCopyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.This material safety data sheet (MSDS) is provided as a courtesy in response to a customer request. This product is not regulated under, and a MSDS is not required for this product by the OSHA Hazard Communication Standard (29 CFR 1910.1200) because, when used as recommended or under ordinary conditions, it should not present a health and safety hazard. However, use or processing of the product not in accordance with the product's recommendations or not under ordinary conditions may affect the performance of the product and may present potential health and safety hazards.PRODUCT NAME:3M(TM) Polyimide Film Tape 5419MANUFACTURER:3MDIVISION:Electronics Markets Materials DivisionADDRESS:3M CenterSt. Paul, MN 55144-1000Issue Date: 06/27/2008Supercedes Date: 06/24/2008Document Group:21-4026-7Product Use:Intended Use:AdhesiveBroad temperature specialty tape for application temperatures from -100°F to 500°F.General Use:Silicone Adhesive Trade Secret50-6550Polyimide Film Backing None35-Odor, Color, Grade: Gold colored polyimide film with clear, pressure sensitive adhesiveGeneral Physical Form: SolidImmediate health, physical, and environmental hazards:The environmental properties of this product present a low environmental hazard. This product, when used under reasonable conditions and in accordance with the 3M directions for use, should not present a health hazard. However, use or processing of the product in a manner not in accordance with the product's directions foruse may affect the performance of the product and may present potential health and safety hazards.3.2 POTENTIAL HEALTH EFFECTSEye Contact:No health effects are expected.Skin Contact:No health effects are expected.Inhalation:No health effects are expected.Ingestion:Physical Blockage: Signs/symptoms may include cramping, abdominal pain, and constipation.3.3 POTENTIAL ENVIRONMENTAL EFFECTSThis substance does not leach metals or other RCRA (Resource Conservation and Recovery Act) listed TCLP (Toxic Characteristic Leaching Procedure) hazardous substances at concentrations that would make the product a hazardous waste.4.1 FIRST AID PROCEDURESThe following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed.Eye Contact: No need for first aid is anticipated.Skin Contact:No need for first aid is anticipated.Inhalation:No need for first aid is anticipated.No need for first aid is anticipated.If Swallowed:Autoignition temperature Not ApplicableFlash Point Not ApplicableFlammable Limits -LEL Not ApplicableFlammable Limits -UEL Not Applicable5.2 EXTINGUISHING MEDIAUse fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).5.3 PROTECTION OF FIRE FIGHTERSSpecial Fire Fighting Procedures:Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA).No unusual fire or explosion hazards are anticipated.Unusual Fire and Explosion Hazards:Not applicable.Avoid skin contact with hot material. This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical under normal use conditions.7.2 STORAGENot applicable.Not applicable.8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)8.2.1 Eye/Face ProtectionNot applicable.8.2.2 Skin ProtectionAvoid skin contact with hot material.8.2.3 Respiratory ProtectionUnder normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. 8.2.4 Prevention of SwallowingNot an expected route of exposure.8.3 EXPOSURE GUIDELINESNone EstablishedOdor, Color, Grade: Gold colored polyimide film with clear, pressure sensitive adhesive General Physical Form: SolidAutoignition temperature Not ApplicableFlash Point Not ApplicableFlammable Limits -LEL Not ApplicableFlammable Limits -UEL Not ApplicableBoiling point Not ApplicableDensity No Data AvailableVapor Density Not ApplicableVapor Pressure Not ApplicableSpecific Gravity No Data AvailablepH Not ApplicableMelting point Not ApplicableNilSolubility in WaterMaterials and Conditions to Avoid: None knownHazardous Polymerization: Hazardous polymerization will not occur.Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardousdecomposition products may occur as a result of oxidation, heating, or reaction with another material.ECOTOXICOLOGICAL INFORMATIONNot applicable.CHEMICAL FATE INFORMATIONNot applicable.Waste Disposal Method: Reclaim if feasible. If product can't be reclaimed, dispose of waste product in a sanitary landfill. Alternatively, incinerate the waste product in an industrial, commercial, or municipal incinerator.Not regulated per U.S. DOT, IATA or IMO.US FEDERAL REGULATIONSContact 3M for more information.311/312 Hazard Categories:Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -No Delayed Hazard -No STATE REGULATIONSContact 3M for more information.CHEMICAL INVENTORIESThis product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements. Contact 3M for more information.INTERNATIONAL REGULATIONSContact 3M for more information.NFPA Hazard ClassificationHealth:0Flammability:1Reactivity:0Special Hazards:NoneNational Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.Revision Changes: Not ApplicableDISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.3M MSDSs are available at 。
MSDS英文版格式
MATERIAL SAFETY DATA SHEET (MSDS) FORMAT1.IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND COMPANYUNDERTAKINGProduct Name:Product Information:Company Name:Address:Phone No.Fax No.POSITION / INFORMATION ON INGREDIENTSChemical Name:Product Code:Hazardous Ingredients / Components:CAS No.Other Components: Risk Phrases & SymbolFor e.g.: Xi = Irritant, R36 = Irritating to eyes, R37 = Irritating to respiratory system, R38 = Irritating to skin3.HAZARDS IDENTIFICATIONHealth: InhalationSkin ContactEye ContactIngestionFire:4.FIRST – AID MEASURESInhalation:Skin Contact:Eye Contact:Ingestion:5.FIRE FIGHTING MEASURESExtinguishing media:Fire Fighting Protective Equipment:Specific Hazards:6.ACCIDENTAL RELEASE MEASURESPersonal precautions:Environmental precautions:Method for cleaning up:7.HANDLING AND STORAGEHandling:Storage8.EXPOSURE CONTROL / PERSONAL PROTECTIONEngineering measures:RespiratorsEye ProtectionPersonal protective equipment:GlovesSafety glassesOccupational Exposure Limits – Hazardous Ingredients9.PHYSICAL AND CHEMICAL PROPERTIESAppearance:Form:Colour:Odour:PH (Value):Boiling Point:Melting Point:Flash Point:Flammable Limits:Auto Ignition Temperature:Explosive Properties:Oxidising Properties:Vapour Pressure (mm Hg):Density (g/ml):Solubility (Water):Solubility (Other):Partition Coefficient:10.STABILITY AND REACTIVITYHazardous Reactions:Hazardous Decomposition Product(s):Conditions to avoid:Materials to avoid:11.TOXICOLOGY INFORMATIONInhalation (LC50):Skin Contact (Dermal – LD50):Eye Contact:Ingestion (Oral – LD50)12.ECOLOGICAL INFORMATIONEnvironmental Hazards:Persistence and Degradation:Toxicity:Effect on Effluent Treatment:13.DISPOSAL CONSIDERATIONSProduct & contaminated packaging:14.TRANSPORT INFORMATIONIATA:ADR:IMO:UN NO.:15.REGULATORY INFORMATIONClassification and labeling Danger symbol:Danger Label:Safety phrases:16.OTHER INFORMATION。
MATERIALSAFETYDATASHEET原材料安全性数据表-CPOOutlets
COMPONENTS DENSITY
成份
密度
Lead 铅
11.34
Lead Sulfate 硫酸铅 Lead Dioxide 氧化铅 Sulfuric Acid 硫酸 Fiberglass Sep. 玻璃纤维隔板 ABS or PP
6.2 9.4 About 1.3 N/A N/A
MELTING POINT 化点
COMPONENTS 成分
Lead 铅(Pb, PbO2, PbSO4) Sulfuric Acid 硫酸 Fiberglass Separator 纤维玻璃隔板 ABS or PP ABS 或 PP
%WEIGHT 所占比重 About 大约
70% About 20% About 5%
About 5%
SECTION 6: CONTROL MEASURES 第 6 部分：控制方法 1. Store lead/acid batteries with adequate ventilation. Room ventilation is required for batteries utilized for standby
WASTE DISPOSAL METHOD:废物外理方法 Neutralized acid may be flushed down the sewer. Spent batteries must be treated as hazardous waste and disposed of according to local state, and federal regulations. A copy of this material safety data must be supplied to any scrap dealer or secondary smelter with battery.中和的酸可能会被冲至下水道。失效的电池必须作为有毒废 品，根据当地的要求进行处理。提供一份原材料安全性数据给废物处理经销商或电池二级炼外 ELECTRICAL SAFETY 电安全性 Due to the battery’s low internal resistance and high power density. High levels of short circuit can be developed across the battery terminals. Do not rest tools or cables on the battery. Use insulated tools only. 由于电池的底内 阻、高能量密度。高水平的短路能发展到电池端子上。不要将工具和线放在电池上。只使用绝缘工具。 Follow all installation instruction and diagrams when installing or maintaining battery systems. 安装或维护电池系统时，参考安装说明书和图
MATERIALSAFETYDATASHEET原材料安全性数据表-CPOOutlets
None 没有
EXPLOSIVE LIMITS 暴炸限定 None None
4% - 74.2%
N/A N/A
COMMENTS 注解
Sealed batteries can emit hydrogen only if over charged (float voltage> 2.4 VPC). The gas enters the air through the vent caps. To avoid the chance of a fire or explosion, keep sparks and other sources of ignition away from the battery. 只有在过充时（float voltage> 2.4 VPC），密封电池 能发出氢气。气体经通风阀向大气排出。要防止爆炸 或火，火花或者其它的火源接近电池 Extinguishing Media: Dry chemical, foam, CO2 灭火器：干化学泡沫 CO2 Toxic vapors may be released.有毒的气体会放出 In case of fire: wear self-contained breathing apparatus.万一着火，穿上自带呼吸的设备 Temperatures over 300 °C (572°F) may release combustible gases. In case of fire: wear positive pressure self-contained breathing apparatus. 温度超过 300 °C (572°F)会发出易燃性气体。万一有 火，穿上自带呼吸的设备
SECTION 7: HEALTH HAZARD DATA 第 7 部分：安全的 HAZARD 数据
Materialsafetydatasheet材料安全数据表
Respiratory Protection
No respiratory protection is required under normal usage
Hand Protection
No special protection needed.
3. Hazards Identification（危险性鉴别）
Overall Hazard Classification危害级别
Not hazardous (无危害性成份)
Route of Exposure暴露途径
Skin contact and accidental ingestion皮肤接触和意外吞食
Inhalation吸入
No volatile, No first aid should be needed.不挥发,无需急救
Ingestion食入
If swallowed large amount, get medical attention immediately if ill effects occur.如大量吞食并出现不适症状，请立即求医
Chronic慢性
Skin皮肤
Prolonged skin contact may cause irritation长时期的皮肤接触可能引起过敏
Inhalation吸入
No volatile No Known applicable information无
Ingestion食入
Repeated ingestion or swallowing large amount may injure internally.重复或大量摄入或吞食可能会造成内部伤害
Materialsafedatasheet(材料安全数据表)
Material safe data sheet（材料安全数据表）The first minute（第一部分）: Product name and company's information（产品名称及公司信息）Product name（产品名称）: Luminescent pigment （发光颜料）Product mode（产品型号）：ZnSWCompany's information（公司信息）: Guangzhou tianyu limited company （广州田宇贸易有限公司）Address:No.28 Hhamei Street,LongDong,Tianhe,Guanzhou,China（广州市天河区龙洞华美路28号）Tel: 86-20-87210918FAX: 86-20-87065181It is second and partial（第二部分）: Dangerousness is general to stat（危险性概述）Dangerousness classification（危险性类别）: It is not dangerous article（不是危险品）Invade channel:（侵入途径）Suck in and eat to enter（吸入、食入）Healthy harm（健康危害）: For skin and respiratory tract, mucous membrane has stimulate（对皮肤、呼吸道粘膜有刺激）Environmental harm（环境危害）: This material dust has light pollutive harm for environment（该物质粉尘对环境有轻微污染危害）Burn Bao danger（燃爆危险）: It is not inflammable to burn and explode（不易燃烧、爆炸）3th is partial: （第三部分）Product mix and chemistry form information（产品结构及化学组成信息）Molecular formula（分子式）: ZnS:Cu4th is partial（第四部分）: The measure of first aid急救措施Suck in and eat to enter:(吸入/食入)If suck in this article dust carelessly, please wash nasal cavity and oral cavity with plenty of waters, if have , it is improper, please go to hospital as soon as possible to treat. （如不小心吸入本品粉尘，请用大量水冲洗鼻腔、口腔，如有不适，请尽快就医治疗。
MATERIALSAFETYDATASHEET1.CHEMICAL…
SDS: 0021138Date Prepared: 01/31/2014MATERIAL SAFETY DATA SHEET_____________________________________________________________________________1.CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct Name:TMPTA Synonyms:None Chemical Family:Acrylated resin Molecular Formula:Mixture Molecular Weight:MixtureAllnex USA Inc., 9005 Westside Parkway, Alpharetta, Georgia 30009, USAFor Product and all Non-Emergency Information call your local Allnex contact point or contact us at/contactEMERGENCY PHONE (24 hours/day) - For emergency only involving spill, leak, fire, exposure or accident call:Asia Pacific:Australia: +61 2801 44558 (Carechem 24)China (PRC): +86(0)532-8388-9090 (NRCC)Japan: +81 345 789 341 (Carechem 24)New Zealand: +64 9929 1483 (Carechem 24)All Others: +65 3158 1074 (Carechem 24)Europe/Africa/Middle East (Carechem 24):Europe, Middle East, Africa, Israel: +44 (0) 1235 239 670Middle East, Africa (Arabic speaking countries): +44 (0) 1235 239 671Latin America (Carechem 24):Brazil: +55 113 711 9144Mexico and all others: +52-555-004-8763Canada and USA (Carechem 24 - Allnex29003-NCEC): +1-866-928-0789 (toll free) or +1-215-207-0061_____________________________________________________________________________2. HAZARDS IDENTIFICATIONEMERGENCY OVERVIEWAPPEARANCE AND ODOR:Color:clear colorless to pale yellow Appearance:liquid Odor:ester acrylateSTATEMENTS OF HAZARD:POTENTIAL HEALTH EFFECTSEFFECTS OF EXPOSURE:The acute oral (rat) LD50 and dermal (rabbit) LD50 values are both >2000 mg/kg. Direct contact with this material may cause moderate eye and skin irritation. Repeated or prolonged dermal contact may cause allergic skinreactions. The toxicological properties of this material have not been fully investigated. Refer to Section 11 fortoxicology information on the regulated components of this product._____________________________________________________________________________3. COMPOSITION/INFORMATION ON INGREDIENTSCAUSES EYE AND SKIN IRRITATIONMAY CAUSE ALLERGIC SKIN REACTIONWARNING!3. COMPOSITION/INFORMATION ON INGREDIENTSOSHA REGULATED COMPONENTSComponent / CAS No.%Carcinogen99 - 100-Trimethylolpropane triacrylate15625-89-5−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− 4. FIRST AID MEASURESEye Contact:Rinse immediately with plenty of water for at least 15 minutes. Obtain medical attention immediately.Skin Contact:Remove contaminated clothing and shoes without delay. Wash immediately with plenty of water. Do not reuse contaminated clothing without laundering. Get medical attention if pain or irritation persists after washing or if signs and symptoms of overexposure appear.Ingestion:If swallowed, call a physician immediately. Only induce vomiting at the instruction of a physician. Never give anything by mouth to an unconscious person.Inhalation:Remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptoms.−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− 5. FIRE-FIGHTING MEASURESSuitable Extinguishing Media:Use water spray, alcohol foam, carbon dioxide or dry chemical to extinguish fires. Water stream may be ineffective. Extinguishing Media to Avoid:high pressure water jet.Protective Equipment:Firefighters, and others exposed, wear self-contained breathing apparatus. Wear full firefighting protective clothing. See MSDS Section 8 (Exposure Controls/Personal Protection).Special Hazards:Keep containers cool by spraying with water if exposed to fire.−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− 6. ACCIDENTAL RELEASE MEASURESPersonal precautions:Where exposure level is not known, wear approved, positive pressure, self-contained respirator. Where exposure level is known, wear approved respirator suitable for level of exposure. In addition to the protective clothing/equipment in Section 8 (Exposure Controls/Personal Protection), wear impermeable boots.Methods For Cleaning Up:Remove sources of ignition. Cover spills with some inert absorbent material; sweep up and place in a waste disposal container. Flush spill area with water.Environmental Precautions:None known−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−−7. HANDLING AND STORAGEHANDLINGPrecautionary Measures: Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist. Keep container tightly closed. Use with adequate ventilation. Wash thoroughly after handling.Special Handling Statements: Product exposed to sunlight will slowly polymerize.STORAGEContainers which are opened must be carefully resealed and kept upright to prevent leakage. Prevent unauthorised access. Storage in stainless steel, amber glass, amber polyethylene or baked phenolic lined container. Keep containers tightly closed. Keep away from heat.Storage Temperature: Store at 4 - 40 °C 39.2 - 104 °FReason: Safety._____________________________________________________________________________ 8. EXPOSURE CONTROLS/PERSONAL PROTECTIONEngineering Measures:Utilize a closed system process where feasible. Where this material is not used in a closed system, good enclosure and local exhaust ventilation should be provided to control exposure.Respiratory Protection:For operations where inhalation exposure can occur use an approved respirator. Recommendations are listed below. Other protective respiratory equipment may be used based on user's own risk assessment.Recommended respirators include those certified by NIOSH.Recommended:Full Face Mask with organic vapor cartridge, Type A filter (BP >65°C)Eye Protection:Prevent eye and skin contact. Provide eye wash fountain and safety shower in close proximity to points of potential exposure. Wear eye/face protection such as chemical splash proof goggles or face shield.Skin Protection:Prevent contamination of skin or clothing when removing protective equipment. Wear impermeable gloves and suitable protective clothing.Hand Protection:Wear protective gloves. Recommendations are listed below. Other protective materials may be used based on user's own risk assessment. Barrier creams may help to protect the exposed areas of the skin, they should however not be applied once exposure has occurred. Replace gloves immediately when torn or any change in appearance (dimension, color, flexibility etc.) is noticed.Gloves for short term exposure:Laminated multilayer gloves, break through time: > 60 minNitrile rubber (NBR), thickness: > 0.56 mm, break through time: < 60 minThe chemical resistance depends on the type of product and amount of product on the glove. Therefore gloves need to be changed when in contact with chemicals.Not suitable gloves:Latex glovesDue to many conditions (e.g. temperature, abrasion) the practical usage of a chemical protective glove in practice may be much shorter than the permeation time determined through testing.Additional Advice:Food, beverages, and tobacco products should not be carried, stored, or consumed where this material is in use. Before eating, drinking, or smoking, wash face and hands thoroughly with soap and water.−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− Exposure Limit(s)No values have been established.−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− 9. PHYSICAL AND CHEMICAL PROPERTIESColor:clear colorless to pale yellowAppearance:liquidOdor:ester acrylateBoiling Point:>100 °CMelting Point:Not availableVapor Pressure:<1.33hPa @ 20 °CSpecific Gravity/Density: 1.11 g/cm3Vapor Density:Not availablePercent Volatile (% by wt.):<0.3 %pH: Not availableSaturation In Air (% By Vol.):Not availableEvaporation Rate:Not availableSolubility In Water:Not availableVolatile Organic Content:Not availableFlash Point:>100 °C 212 °F Cleveland Open CupFlammable Limits (% By Vol):Not applicableAutoignition Temperature:Not availableDecomposition Temperature:Not availablePartition coefficient (n-octanol/water):Not availableOdor Threshold:Not available_____________________________________________________________________________ 10. STABILITY AND REACTIVITYStability:StableConditions To Avoid:Avoid exposure to strong UV sources. Avoid friction with temperature increase asresult. Avoid direct contact with heat sources. Avoid temperatures higher than 60°C.Protect from direct sunlight.Polymerization:May occurConditions To Avoid:Hazardous polymerization can occur when exposed to direct sunlight. Hazardousexothermic polymerization can occur when heated. Uncontrolled polymerization maycause rapid evolution of heat and increase in pressure that could result in violentrupture of sealed storage vessels or containersMaterials To Avoid:Avoid contact with oxidizing agents.Avoid contact with acids and alkali''s.Avoid free radical producing initiators.Avoid contact with reactive metals.Avoid contact with peroxides.Unintentional contact with them should be avoided.They give an exothermic reaction with the product.Hazardous Decomposition Products:oxides of carbon hydrocarbons−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− 11. TOXICOLOGICAL INFORMATION11. TOXICOLOGICAL INFORMATIONToxicological information for the product is found under Section 2. HAZARDS IDENTIFICATION.Toxicological information on the regulated components of this product is as follows:Trimethylolpropane triacrylate has acute oral (rat) LD50 and acute dermal (rabbit) LD50 values of 5760 mg/kg and 7050 mg/kg, respectively. Direct contact with this material may cause moderate eye and skin irritation. Repeated or prolonged skin contact may cause allergic skin reactions. Results of in vitro mutagenicity testing for trimethylolpropane triacrylate are mixed with both positive and negative findings. Trimethylolpropane triacrylate may cause mutagenic eefects based on in vitro studies. However, a more definitive in vivo study indicates trimethylolpropane triacrylate is not mutagenic (non-genotoxic). Additionally, in a long-term bioassay in which trimethylolpropane triacrylate was applied dermally to mice, trimethylolpropane triacrylate was determined to be non-carcinogenic. Therefore, the weight of the evidence of various genotoxicity (mutagenicity) test results leads to the conclusion that trimethylolpropane triacrylate is not mutagenic.In January 2013, the National Toxicology Program (NTP) released their final report regarding the toxicology and carcinogenesis studies of Trimethylolpropane triacrylate (TMPTA). The report indicates that there was some evidence of carcinogenic activity of TMPTA in a 2-year dermal study that was conducted in rodents. At least one or more of the findings are notably specific to rodents and should have no relevance to humans. The other findings are believed by some experts to be inappropriately related to the treatment with TMPTA. Further investigation of the findings in this study is ongoing.California Proposition 65 Warning (applicable in California only) - This product contains (a) chemical(s) known to the State of California to cause birth defects or other reproductive harm._____________________________________________________________________________ 12. ECOLOGICAL INFORMATIONThe ecological properties of this material have not been fully investigated.ECOTOXICITYNot availableBIOACCUMULATIVE POTENTIALNot availablePERSISTENCE AND DEGRADABILITYNot availableMOBILITY IN SOILNot availableOTHER ADVERSE EFFECTSHAZARD TO THE OZONE LAYERNot available13. DISPOSAL CONSIDERATIONS13. DISPOSAL CONSIDERATIONSThe information on RCRA waste classification and disposal methodology provided below applies only to the product, as supplied. If the material has been altered or contaminated, or it has exceeded its recommended shelf life, the guidance may be inapplicable. Hazardous waste classification under federal regulations (40 CFR Part 261 et seq) is dependent upon whether a material is a RCRA "listed hazardous waste" or has any of the four RCRA "hazardous waste characteristics." Refer to 40 CFR Part 261.33 to determine if a given material to be disposed of is a RCRA "listed hazardous waste"; information contained in Section 15 of this MSDS is not intended to indicate if the product is a "listed hazardous waste." RCRA Hazardous Waste Characteristics: There are four characteristics defined in 40 CFR Section 261.21-61.24: Ignitability, Corrosivity, Reactivity, and Toxicity. To determine Ignitability, see Section 9 of this MSDS (flash point). For Corrosivity, see Sections 9 and 14 (pH and DOT corrosivity). For Reactivity, see Section 10 (incompatible materials). For Toxicity, see Section 3 (composition). Federal regulations are subject to change. State and local requirements, which may differ from or be more stringent than the federal regulations, may also apply to the classification of the material if it is to be disposed. The Company encourages the recycle, recovery and reuse of materials, where permitted, as an alternate to disposal as a waste. The Company recommends that organic materials classified as RCRA hazardous wastes be disposed of by thermal treatment or incineration at EPA approved facilities.The Company has provided the foregoing for information only; the person generating the waste is responsible for determining the waste classification and disposal method.−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− 14. TRANSPORT INFORMATIONThis section provides basic shipping classification information. Refer to appropriate transportation regulations for specific requirements.US DOTDangerous Goods? Not applicable/Not regulatedTRANSPORT CANADADangerous Goods? Not applicable/Not regulatedICAO / IATADangerous Goods? Not applicable/Not regulatedIMODangerous Goods? Not applicable/Not regulated_____________________________________________________________________________ 15. REGULATORY INFORMATIONInventory InformationUnited States (USA): All components of this product are included on the TSCA Chemical Inventory or are not required to be listed on the TSCA Chemical Inventory.Canada: All components of this product are included on the Domestic Substances List (DSL) or are not required to be listed on the DSL.European Economic Area (including EU): When purchased from an Allnex legal entity based in the EEA (EU or Norway), this product is compliant with the registration of the REACH Regulation (EC) No. 1907/2006 as all its components are either excluded, exempt, pre-registered and/or registered.Australia: All components of this product are included in the Australian Inventory of Chemical Substances (AICS) or are not required to be listed on AICS.China: All components of this product are included on the Chinese inventory or are not required to be listed on the Chinese inventory.Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required to be listed on the Japanese inventory.Korea: All components of this product are included on the Korean (ECL) inventory or are not required to be listed on the Korean inventory.Philippines: All components of this product are included on the Philippine (PICCS) inventory or are not required to be listed on the Philippine inventory.Switzerland: All components of this product are exempt from the new substance notification requirements for Switzerland (SR 813.11 art. 16-17).OTHER ENVIRONMENTAL INFORMATIONThe following components of this product may be subject to reporting requirements pursuant to Section 313 of CERCLA (40 CFR 372), Section 12(b) of TSCA, or may be subject to release reporting requirements (40 CFR 307, 40 CFR 311, etc.) See Section 13 for information on waste classification and waste disposal of this product.This product does not contain any components regulated under these sections of the EPAPRODUCT HAZARD CLASSIFICATION UNDER SECTION 311 OF SARA•Acute•Reactivity_____________________________________________________________________________ 16. OTHER INFORMATIONNFPA Hazard Rating (National Fire Protection Association)Health: 2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury.Fire: 1 - Materials that must be preheated before ignition can occur.Instability: 1 - Materials that in themselves are normally stable, but that can become unstable at elevatedtemperatures and pressures.Reasons For Issue:Company address changedDate Prepared:01/31/2014Date of last significant revision:06/01/2013−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−−Prepared By: Product Stewardship & Regulatory Affairs Department, /contact −⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−− This information is given without any warranty or representation. We do not assume any legal responsibility for same, nor do we give permission, inducement, or recommendation to practice any patented invention without a license. It is offered solely for your consideration, investigation, and verification. Before using any product, read its label.−⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯−−。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
MATERIAL SAFETY DATA SHEET EXPANDED PERLITE PROUCTS化学品安全技术说明书1 . PRODUCT AND COMPANY INFORMATION产品和公司信息DICALITE MINERALS CORP. 1 Bala Avenue, Suite 310, BalaCynwyd, PA 19004 Trade Name(s):商标名：Dicalite,Dicaperl, Chemrock/Noble Perlite Expanded Perlite Products: (Aerosoil, Attic-Fill, Chemsil (All CS-Grades), Blockfil, Permalite, Dica-Pool,Dicaperl HP Microsphere Series (All Grades),416,426,436,436L456,476,476SP,41064156,LD1006,LD1106,LD1106S, FF-(All Grades), Hi-Float,Lo-Float,Con-Agg,CH-30FP1000, Sourced from Socorro Perlite Ore.Dicalite,Dicaperl, Chemrock/Noble Perlite Expanded Perlite Products: (Aerosoil, Attic-Fill, Chemsil (All CS-Grades), Blockfil, Permalite, Dica-Pool,Dicaperl HP Microsphere Series (All Grades),416,426,436,436L456,476,476SP,41064156,LD1006,LD1106,LD1106S, FF-(All Grades), Hi-Float,Lo-Float,Con-Agg,CH-30FP1000, Sourced from Socorro Perlite Ore.Generic Name: Perlite, Expanded, Amorphous Alumina Silicate俗名：蓬松珠光砂；非晶状硅酸铝CAS #: 93763-70-3CAS编号：93763-70-3EINECS: NA欧洲现有化学物质总量编号：不适用Formula: Predominantly Alumina-Silicate分子式：主要为硅酸铝Chemical Name: Perlite化学名：珠光砂Manufacturer: DICALITE MINERALS CORP/ DICAPERL MINERALS, INCNOBLE PERLITE LLC.制造商：DICALITE MINERALS CORP/ DICAPERL MINERALS, INCNOBLE PERLITE LLC. Address: 1 Bala Ave, Suite 310地址：1 Bala Ave, Suite 310Telephone: (610)660-8840 (530)-335-5451电话：(610)660-8840 (530)-335-5451City: BalaCynwyd State: PA Zip: 19004城市：BalaCynwyd 洲：PA 邮编：19004Primary Material Use: Multi-Functional Industrial/Commercial Mineral主要用途：多功能工业/商业矿物质Date of Preparation: 11/05/08 by: Dicalite/Dicaperl Minerals生产日期：08年5月8日原料：二价铁镍铝合金矿物质2. COMPOSITION-INGREDIENT INFORMATION2、组成信息INGREDIENT NAMECAS NUMBER % PEL/TLV组分名称 CAS号含量% 时间加权暴露限值Perlite, Alumina Silicate 93763-70-3 100 See Below珠光砂，硅酸铝93763-70-3 100 见下文Quartz 14808-60-7 (< 1.5%)石英 14808-60-7 (< 1.5%) Respirable Quartz, ACGIH 0.025mg/M3吸入限值：ACGIH 0.025mg/M33. HAZARDS IDENTIFICATION危险性概述Appearance: White to off-white, no specific odor.外观：白色至灰白色，无特别味道OSHA Regulations Status: OSHA 29CFR 1910.1200OSHA法规状态：OSHA 29CFR 1910.1200Potential Health Effects: See section 11 Toxocological information.潜在的健康影响：参考第11部分毒理学信息Primary Entry Routes: See below主要的侵入途径：见下文Eyes: Temporary irritation or inflammation眼睛：短暂的刺激或灼痛Skin: May cause dryness with continued exposure.皮肤:持续暴露可导致皮肤干燥Ingestion: Not considered harmful in small amounts, but mouth,throat and stomachirritation may occur.摄取（食入）：少量摄取不会造成危害，但可造成嘴、喉和胃部刺激。
Chronic Health Effects: This product may contain crystalline silica (CS), which is classified as a hazard byinhalation.Long term inhalation of respirable crystalline silica dusts in excess of the TLV(threshold limit value), over a prolonged period may cause a non-cancerous lung disease (silicosis). Inhalation of respirable crystalline silica has been classified as carcinogenic(Group1) byIARC, a unit of the World Health Organization. Respirable crystalline silica islisted by the NTP as a known human carcinogen.Conditions aggravated by Upper respiratory and lung disease such as bronchitis, emphysema,and exposurepre-existing conditions: asthma.慢性健康影响：该产品含有晶状硅，该物质存在吸入危害。
长期吸入可吸入的晶状硅粉尘超过TLV(时间加权浓度职业暴露限值)，可造成非致癌性肺病（矽肺）。
晶状硅已被IARC（一家世界卫生组织）分类为第一类致癌物。
晶状硅被NTP列为已知的致癌物。
该粉尘条件可加重上呼吸道和肺部疾病，如支气管炎、肺气肿、如已患有哮喘等。
4. FIRST AID MEASURES急救措施Eyes: Do not rub eyes. Flush eyes with copious amounts of water to remove any dust particles.Consult aphysician if irritation persists.眼睛接触：不要揉眼睛。
用充足的水冲洗眼睛与清除粉尘颗粒。
如果感到刺激需就医。
Inhalation: Remove from dusty area; drink water to clear throat; blow nose to evacuate dust.吸入：脱离粉尘区域，饮水清洗咽喉，打喷嚏以排出粉尘。
Skin Contact: Use moisturizing lotions if dryness occurs.皮肤接触：如感到干燥，使用润肤液清洗。
Skin Absorption: NA皮肤吸收：不适用Ingestion: Drink copious amounts of water to reduce bulk and dryness effects.摄入（食入）：喝大量的水以减少结块和干渴的影响。
5. FIRE FIGHTING MEASURES消防措施Flash Point(Method): Nonflammable闪点：不燃NFPA Flammable/Combustible N/ANFPA 可燃/易燃物分类：不适用Flammable Limits: N/A燃烧范围：不适用Liquid Classification: N/A液体燃烧分类：不适用Extinguishing Media: N/A灭火介质：不适用Auto-Ignition Temperature: N/A自燃温度：不适用Unusual Fire or Explosion Hazards : None异常的火灾或爆炸危害：无Special FireFightingProcedures: None特殊的灭火程序：无6. ACCIDENTAL RELEASE MEASURES泄漏处理措施Personal Precautions Use proper PPE (See section 8)个人防护措施：使用适当的PPE（参见第8部分）Environmental Precautions No significant environmental impact环境保护措施：没有重要的环境影响Containment and Cleanup Clean up material with vacuum equipped with HEPA filter. Usewater as dust suppressant if necessary.收集与清扫：使用带有HEPA过滤器的真空设备清洁该材料。