环保溶剂EEP混酯说明书
不饱和聚酯树脂msds
不饱和聚酯树脂msds化学品中文名：不饱和聚酯树脂英文名称： unsaturated polyester resin 成分 /组成纯品；混合物 ( 不饱和聚酯 /苯乙烯 )信息化学品名称：不饱和聚酯树脂有害物成分 : 苯乙烯， CAS No. ： 100-42-5 ，含量 : 40%-46%危险特性危险性类别：第 3.3 类高闪点易燃液体侵入途径：吸入、皮肤和眼睛接触。
健康危害：皮肤接触：对皮肤有刺激，长时间或重复接触会导致皮肤脱脂和干燥；眼睛接触：灼痛、流泪、红肿；吸入：吸入有害，会导致头痛、疲劳、恶心、步态蹒跚、中枢神经抑制、肺水肿；食入：极少量无严重后果，大量时，会喉咙痛、胃痛、失调不舒服，还可能有与吸入相同的症状。
环境危害：对环境有危害，对水体、土壤和大气可造成污染。
燃爆危险：本品易燃，具刺激性。
急救措施皮肤接触：用肥皂和水清洗，脱去已污染的衣服。
情形严重时应就医；眼睛接触：立即用大量的清水冲洗15 分钟以上，必须立即就医；吸入：移至空气新鲜处，保持温暖与安静。
如果呼吸困难，吸氧。
如果呼吸停止，进行人工呼吸。
情形严重者，立即就医；食入：不要催吐，否则可能会使树脂进入肺部。
马上喝两杯水或牛奶。
立即就医。
消防措施危险特性：易燃液体有害燃烧产物： CO、 COB2B，及其它刺激性或有毒的蒸汽和气体。
灭火方法及灭火剂：干粉、二氧化碳、泡沫等。
灭火注意事项：从着火处疏散人员。
消防人员穿防护服，佩戴呼吸装置。
泄漏应急应急处理：少量泄露时，用沙土等惰性物质进行吸附后，放入危险品废弃物容处理器中。
大量泄露时，消除火源，制止泄漏，疏散人员。
防止树脂污染土壤，防止入下水道，河流等水体。
立即向相关政府部门报告。
消除方法：能回收的树脂应回收，污染物放入危险品废弃物容器中，根据相关法律法规处理。
操作处置操作注意事项：避免吸入，避免接触眼睛、皮肤和衣服。
在通风处操作。
采取与储存措施，防止静电。
包装容器应妥善处理。
储存注意事项：远离火源，避免阳光直射，严禁吸烟。
(word完整版)聚氨脂化学品安全说明书
临界温度(℃）：临界压力（mPa）：无资料
辛醇/水分配系数的对数值：无资料
闪点（℃):无资料 引燃温度（℃）：无资料
爆炸上限[%(V/V)]：无资料 爆炸下限［％(V/V）］:无资料
溶解性:溶于丙酮、乙二醇、甲苯.
主要用途：制备氨基甲酸乙酯聚合体的成分，我们建议您按照所列出的方式使用本品，如果您所采取的方式与所述规定不一致，请联系您好的销售人员或技术服务代表.
第七部分 操作处置与储存
操作注意事项：密闭操作,提供良好的自然通风条件。操作人员必须经过专门培训，严格遵守操作规程。建议操作人员佩戴自吸过滤式防尘口罩，戴化学安全防护眼镜。远离火种、热源，工作场所严禁吸烟。使用防爆型的通风系统和设备。防止蒸气泄漏到工作场所空气中。避免与氧化剂接触。搬运时要轻装轻卸，防止包装及容器损坏。配备相应品种和数量的消防器材及泄漏应急处理设备。倒空的容器可能残留有害物.
PC-STEL（mg/m3)：未制定标准TLV-C（mg/m3）：未制定标准
TLV—TWA（mg/m3）:TLV—STEL(mg/m3）:
监测方法:无资料.
工程控制：密闭操作。提供良好的自然通风条件。
呼吸系统防护：空气中浓度超标时，佩戴过滤式防尘呼吸器.
眼睛防护：一般不需要特殊防护,高浓度接触时可戴化学安全防护眼镜。
第十三部分 废弃处置
废弃物性质：危险废物 废弃
废弃处置方法：建议用焚烧法处置。
废弃注意事项：处置前应参阅国家和地方有关法规。
第十四部分 运输信息
危险货物编号：32197
UN编号：无资料
包装类别：Ⅱ类包装
包装标志：易燃体
包装方法：无资料。
运输注意事项：运输时运输车辆应配备相应品种和数量的消防器材及泄漏应急处理设备。严禁与氧化剂、食用化学品、混装混运。运输途中应防曝晒、雨淋，防高温。按规定路线行驶，勿在居民区和人口稠密区停留。
巴斯夫安全技术说明书-甲基丙烯酸环已酯
安全技术说明书页: 1/14 巴斯夫安全技术说明书按照GB/T 16483编制日期 / 本次修订: 15.11.2022版本: 11.0日期/上次修订: 02.09.2021上次版本: 10.0日期 / 首次编制: 12.09.2006产品: 甲基丙烯酸环已酯Product: Cyclohexyl Methacrylate (CHMA)(30208746/SDS_GEN_CN/ZH)印刷日期 02.09.20231. 化学品及企业标识甲基丙烯酸环已酯Cyclohexyl Methacrylate (CHMA)推荐用途和限制用途: 单体。
公司:巴斯夫(中国)有限公司中国上海浦东江心沙路300号邮政编码 200137电话: +86 21 20391000传真号: +86 21 20394800E-mail地址: **********************紧急联络信息:巴斯夫紧急热线中心（中国）+86 21 5861-1199巴斯夫紧急热线中心（国际）:电话: +49 180 2273-112Company:BASF (China) Co., Ltd.300 Jiang Xin Sha RoadPu Dong Shanghai 200137, CHINA Telephone: +86 21 20391000Telefax number: +86 21 20394800E-mail address: ********************** Emergency information:Emergency Call Center (China):+86 21 5861-1199International emergency number: Telephone: +49 180 2273-1122. 危险性概述纯物质和混合物的分类:易燃液体: 分类4巴斯夫安全技术说明书日期 / 本次修订: 15.11.2022版本: 11.0产品: 甲基丙烯酸环已酯Product: Cyclohexyl Methacrylate (CHMA)(30208746/SDS_GEN_CN/ZH)印刷日期 02.09.2023皮肤致敏物: 分类1特异性靶器官毒性-一次接触: 分类3 (对呼吸道系统有刺激性)对水环境的急性危害: 分类3标签要素和警示性说明:图形符号:警示词:警告危险性说明:H227可燃液体。
不饱和聚酯树脂化学品安全技术说明书
生效日期： 2009 年 11 月 5 日
第二部分：成分/组成信息
有害物成分 苯乙烯
含量 25-45%
理化特性 稳定性和反应活性 毒理学资料 生态学资料 废弃处置 运输信息 法规信息 其他信息
CAS No. 100-42-5
第三部分：危险性概述 危险性类别： 第 3．3 类高闪点易燃液体
侵入途径： 吸入食入经皮吸收
接触控制/个体防护
第十六部分
第一部分：化学品名称及企业标识
化学品中文名称： 不饱和聚酯树脂（混合物）
化学品英文名称： Unsaturated Polyester resin
生产企业名称： 漳州亚邦化学有限公司
地址： 漳州市金峰开发区北斗工业园
邮编： 363000
传真：
应急电话：
技术说明书编码： YB01
螺纹口玻璃瓶、塑料瓶或镀锡薄钢板桶（罐）外满底板花格箱、纤维板箱或胶合板箱。 运输注意事项： 铁路运输时应严格按照铁道部《危险货物运输规则》中的危险货物配装表进行配装。运输时运输车辆应配备
相应品种和数量的消防器材及泄漏应急处理设备。夏季最好早晚运输。运输时所用的槽（罐）车应有接地链， 槽内可设孔隔板以减少震荡产生静电。严禁与氧化剂、酸类、食用化学品等混装混运。运输途中应防曝晒、 雨淋，防高温。中途停留时应远离火种、热源、高温区。装运该物品的车辆排气管必须配备阻火装置，禁止 使用易产生火花的机械设备和工具装卸。公路运输时要按规定路线行驶，勿在居民区和人口稠密区停留。铁 路运输时要禁止溜放。严禁用木船、水泥船散装运输。
第十六部分：其他信息
参考文献： 填表部门： 安全环保科 数据审核单位： 技术科 修改说明： 重新规范编制 其他信息：
第十五部分：法规信息 法规信息 化学危险物品安全管理条例 (1987 年 2 月 17 日国务院发布)，化学危险物品安全管理条例实施细则 (化劳发
EEP3-乙氧基丙酸乙酯产品特性及应用领域
EEP3-乙氧基丙酸乙酯产品特性及应用领域
EEP 3-乙氧基丙酸乙酯产品特性及应用领域
文章撰写人：smartchemi,时间：20150312
3-乙氧基丙酸乙酯是一种天然环保的应用广泛有机溶剂和有机合成单体，广泛应用于涂料、油墨、胶粘剂行业，电子行业以及精细化工中间体的合成生产。
文章目录
一、EEP环保溶剂简介
二、EEP 3-乙氧基丙酸乙酯物化指标：
（一）、EEP技术指标：
（二）、EEP 3-乙氧基丙酸乙酯产品特点:
三、EEP 3-乙氧基丙酸乙酯生产工艺
四、EEP应用范围：
（一）、化工树脂工业：
（二）、涂料工业：
（三）、印刷油墨工业：
（四）、清洗剂行业：
（五）、电子电器工业：
（六）、化工中间体：
五、EEP储运注意项：
六、EEP 3-乙氧基丙酸乙酯溶剂应用配方
（一）、EEP用于半导体清洗剂配方；
（二）EEP用于涂布型哑光离型剂配方；
（三）、EEP用于耐腐蚀型橡胶配方；
（四）、EEP用于常温金属脱漆剂配方；
（五）、EEP用于OEM高固体份汽车面漆涂料配方；
（六）、EEP用于UV紫外光固化丝印油墨配方；
（七）、EEP用于耐高温丝印油墨配方；
（八）、EEP用于双组分五金氟碳涂料配方；
（九）、EEP用于单组份低温固化导电银浆配方；
(十)、EEP用于纳米改性银色氟碳涂料配方。
DB82655-80产品技术说明书
DB82655-80产品技术说明书（TDS）产品介绍DB82655-80是一种基于六亚甲基二异氰酸酯（HDI)的亲水性脂肪族聚异氰酸酯，用作水性双组分聚氨酯体系的固化剂组分，是DB82655用PMA稀释成80%的产品。
技术参数项目指标NCO含量（%）16.8±0.5有效成分（%）80±1溶剂PMA（丙二醇甲醚醋酸酯）粘度，25°C（mPa·s）100-500Hazen色值≤100异氰酸酯单体含量（%）<0.3密度（g/cm3）≈1.12使用特性DB82655-80是DB82655用PMA稀释成固含量为80%的产品，一般而言，本产品与有机溶剂如酯类、醚酯类、二甲苯和溶剂石脑油100号相容性良好。
但对于每种溶剂均应测试其溶解性与相容性。
使用聚氨酯级溶剂，含水量不得超过0.05%。
DB82655-80是一种适用于水性体系的交联剂，此类水性体系需具有结合稳定性和耐化学品性好的特点。
该固化剂的亲水性相对较弱，但在水相中，低剪切力的情况下也能快速乳化。
使用该产品制备的涂料可形成高光低雾影膜。
由于具有适中的亲水性和高官能度之间的平衡，使用DB82655-80制备而成的水性双组分聚氨酯涂料具有快干、硬化快速的特点，形成的膜则具有最终硬度高和极佳的耐化学品性特点。
DB82655-80也可用作水性多元醇的交联助剂以及大部分中性水性聚合物分散体（如聚氨酯、聚醋酸乙烯脂、聚丙烯酸酯和合成橡胶分散体）的交联剂。
添加DB82655-80后，待用的双组分涂料必须在活化期内使用。
活化期受聚合物含量和其它组分（如树脂、增稠剂、增塑剂等）的影响。
注意事项产品含有异氰酸酯，皮肤接触本产品可能引起过敏反应。
须遵守物质安全数据表（MSDS)，它包括标签、运输和储存等信息，以及产品使用、产品安全和生态的相关资料。
包装与储运包装规格20kg/桶，220kg/桶，铁桶包装。
该产品对于湿气敏感，必须储存于密封容器中。
环保溶剂丙二醇多元醚醋酸酯(PMMA)
环保溶剂PMMA
丙二醇多元醚醋酸酯
溶剂名称：丙二醇多元醚醋酸酯
溶剂编号：PMMA分子量：140-225
产品基本特性：
1，闪点：61℃，可以普通储存和运输。
2，毒性：属于低毒类环保型溶剂
3，气味：气味极低几乎无味，这是该溶剂的最大亮点。
不仅降低施工气味，产品本身无残留。
4，馏程：主馏程为158-185，由于该溶剂的释放性好，使得湿膜表干慢实干快。
实干性类比环己酮,并以此作为挥发性方面的配方设计参考。
5，PMMA在涂料行业的使用范围：
适用于聚氨酯涂料PU、不饱和聚脂涂料PE、聚酯热固化、聚酯多元醇、热塑性丙烯酸、硝基漆NC、热固丙烯酸等多种体系。
由于产品本身属于中性，不含有氨和游离酸等成份,含水量极低（≤0.05%），适合做更具储存稳定性要求的产品。
6、PMMA在涂料行业的使用范围：
（1）木器涂料：代替丙二醇甲醚醋酸酯PMA（低气味，高光泽，低成本）
（2）汽车涂料：代替乙烷基3-乙氧丙酸酯EEP（低成本，同品质）（3）塑胶涂料：代替乙二醇丁醚BCS、PMA、乙二醇乙醚醋酸酯CAC、二丙酮醇DAA等（高光泽，低成本）
（4）卷材涂料：代替混合二元酸酯DBE、丙二醇二乙酸酯PGDA等（光泽更高，成本更低）
（5）水性涂料：代替丙二醇甲醚PM、BCS等（成膜质量高、成本低、更环保）
（6）丝印油墨及其他油墨：代替EEP、DBE、环己酮CYC、BCS、PMA等慢干溶剂，效果更好
佛山市顺德区零碳化工有限公司。
STYPOL 040-4950 4954 4956 4965 透明高分辨率钢琼酯粘合剂说明书
040-4950, 040-4954, 040-4956, 040-4965Marble Clear Gel CoatsCopyright 2005-2016DescriptionSTYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 are clear MACT compliant NPG isophthalic gel coats. They have been designed for use in the manufacturing of cultured marble, onyx, and granite. Features and Benefits∙Low VOC / HAP content (42% or less)∙Excellent sprayability∙Excellent nonsagging properties∙High clarity∙Excellent chemical and water resistance∙Excellent thermal shock resistance (1)∙UV light stabilized∙Good color retention∙Suitable for low pressure spray equipment∙Meets gel coat test specifications according to ANSI Z124.3∙Meets BAAQMD, Regulation 8-50-1, Method 26 (Bay Area AQMD of Northern California)(1) Note: It is important to remember that many factors other than resin influence the outcome of whether acultured marble part will pass the Thermal Shock Test.Typical Liquid PropertiesTypical liquid properties of STYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 are shown below. These values may or may not be manufacturing control criteria. They are listed as a reference guide only. Particular batches won’t conform exactly to the numbers listed because storage conditions, temperature changes, age, testing equipment (type and procedure) can each have a significant effect on the testing. Products with properties outside of these readings can perform acceptably. Final suitability of this product is shown in the end use performance.040-4950, 040-4954, 040-4956, 040-4965 / Copyright 2005-2016(3) 2% Arkema DDM-9 @ 77°F(4)“Castable” refers to the point at which a gel coat film is ready to be cast upon. Use of heat (90-120°F), such as “gel coat curing tunnels,” can reduce castable time.STYPOL® 040-4950 is the fastest gel and cure version available and is designed for use in colder temperatures.ApplicationSTYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 gel coats must be mixed prior to use. This includes prior to production spray application and when obtaining material for patching or any material that has been set aside for patching. Several suitable types of mixing equipment and styles of agitators are available for both pails and drums. Regardless of the specific type used, the equipment must have sufficient horsepower (relative to container size) to achieve thorough circulation from top to bottom and out to the sides of the container. The agitator must be properly sized for the container and must allow for uniform mixing regardless of the liquid level in the container.Mixing once a day for 10 minutes is typically sufficient. Do not overmix STYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 gel coats. Overmixing can break down the polymer coating viscosity increasing the tendency to sag. Overmixing can also result in styrene loss which could contribute to porosity. Air bubbling should not be used for mixing. It is not effective and only serves as a potential source of water or oil contamination.Low VOC gel coats need to be at 75°F or higher for good sprayability. STYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 are designed for use with airless system gel coat applications. Suggested parameters are an 1840 or 518 tip, 500 to 700 psi fluid pressure, 15 to 20 psi assist air pressure, and 5-7 mils per pass. A large diameter fluid hose as well as an inline heater improves the pumping and sprayability of the material. Because of the lower monomer content, the fan pattern is smaller than with standard gel coats. Tip sizes larger than 18 do not atomize the gel coat correctly.STYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 have also been sprayed through a FIT System using a 1727 tip, 350 to 500 psi of fluid pressure and catalyst air at 15 psi pressure. Use a 1/2-inch hose with a 3/8-inch whip.Higher pump pressures may be needed with smaller diameter hoses (do not go below 3/8 inch hose) or with lower gel coat temperatures.It is advisable to allow some time between passes for air release. Apply 16 to 20 mils on the deck and up to 22 mils on the bowl in three passes.040-4950, 040-4954, 040-4956, 040-4965 / Copyright 2005-2016 Determining castable time can be accomplished with a simple finger test. If a light drag of a finger over the gel coat film picks up gel coat, the gel coat is not yet ready. However, if the same light drag picks up NO gel coat, the matrix can be poured. Note that even when the gel coat is cured, it will be possible to pick up gel coat by applying direct pressure (as opposed to a light drag), and with such pressure, a slight finger print may appear on the cured gel coat film.It is recommended that gel time be checked in the customer's plant because age, temperature, humidity and catalyst will produce varied gel times. The recommended catalyst range for proper cure is 1.5% to 2.5%, with 2.0% being ideal.This product should not be used when temperature conditions are below 75°F, as curing may be adversely affected.CautionDo not add any material, other than the recommended methyl ethyl ketone peroxide, to this product without the advice of a Polynt Composites representative.Storage LimitationsUncatalyzed, STYPOL® 040-4950, 040-4954, 040-4956 and 040-4965 have a shelf life of 60 days from date of manufacture when stored at 73°F or below, in a closed, factory-sealed, opaque container and out of direct sunlight. The shelf life is cut in half for every 20°F over 73°F.SDS / Data SheetsSDS and data sheets can be obtained by contacting your Polynt representative or Polynt Customer Service at 800-322-8103.POLYNT SAFETY INFORMATIONAll sales of products manufactured by Polynt Composites USA Inc. and described herein, are made solely on condition that Polynt Composites USA customers comply with applicable health and safety laws, regulations and orders relating to the handling of our products in the workplace. Before using, read the following information, and both the product label and Safety Data Sheet pertaining to each product. Most products contain styrene. Styrene can cause eye, skin and respiratory tract irritation. Avoid contact with eyes, skin and clothing. Impermeable gloves, safety eyewear and protective clothing should be worn during use to avoid skin and eye contact. Wash thoroughly after use.Styrene is a solvent and may be harmful if inhaled. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Extended exposure to styrene at concentrations above the recommended exposure limits may cause central nervous system depression causing dizziness, headaches or nausea and, if overexposure is continued indefinitely, loss of consciousness, liver and kidney damage.Do not ingest or breathe vapor, spray mists or dusts caused by applying, sanding, grinding and sawing products. Wear an appropriate NIOSH/MSHA approved and properly fitted respirator during application and use of these products until vapors, mists and dusts are exhausted, unless air monitoring demonstrates vapors, mists and dusts are below applicable exposure limits. Follow respirator manufacturer's directions for respirator use.The 12th Report on Carcinogens issued by the National Toxicology Program lists styrene as a “reasonably anticipated” carcinogen, but the Report cautions that the NTP listing does not mean that styrene presents a risk to persons in their daily lives. The Styrene Information and Research Center does not agree with the classification as it did not include a review of all available data. SIRC states: “HHS included styrene in the 12th RoC despite the fact that European Union regulators have determined styrene does not represent a human cancer concern. E.U. scientists reviewed the full styrene database, weighing all of the available data in reaching their conclusion.”The International Agency for Research on Cancer (IARC) reclassified styrene as Group 2B, "possibly carcinogenic to humans." This revised classification was not based on new health data relating to either humans or animals, but on a change in the IARC classification system. The Styrene Information and Research Center does not agree with the reclassification and published the following statement: Recently published studies tracing 50,000 workers exposed to high occupational levels of styrene over a period of 45 years showed no association between styrene and cancer, no increase in cancer among styrene workers (as opposed to the average among all workers), and no increase in mortality related to styrene.Styrene is classified by OSHA and the Department of Transportation as a flammable liquid. Flammable products should be kept away from heat, sparks, and flame. Lighting and other electrical systems in the workplace should be vapor-proof and protected from breakage. Vapors from styrene may cause flash fire. Styrene vapors are heavier than air and may concentrate in the lower levels of molds and the work area. General clean air dilution or local exhaust ventilation should be provided in volume and pattern to keep vapors well below the lower explosion limit and all air contaminants (vapor, mists and dusts) below the current permissible exposure limits in the mixing, application, curing and repair areas.Some products may contain additional hazardous ingredients. To determine the hazardous ingredients present, their applicable exposure limits and other safety information, read the Safety Data Sheet for each product (identified by product number) before using. If unavailable, these can be obtained, free of charge, from your Polynt Composites representative or from: Polynt Composites USA Inc., 99 East Cottage Avenue, Carpentersville, IL 60110, 800-322-8103.FIRST AID: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If affected by inhalation of vapors or spray mist, remove to fresh air. If swallowed, get medical attention. Those products have at least two components that must be mixed before use. Any mixture of components will have hazards of all components. Before opening the packages read all warning labels. Observe all precautions.Keep containers closed when not in use. In case of spillage, absorb with inert material and dispose of in accordance with applicable regulations. Emptied containers may retain hazardous residue. Do not cut, puncture or weld on or near these containers. Follow container label warnings until containers are thoroughly cleaned or destroyed.FOR INDUSTRIAL USE AND PROFESSIONAL APPLICATION ONLY. KEEP OUT OF REACH OF CHILDREN.LIMITED WARRANTY AND LIMITATION OF LIABILITYLIMITED WARRANTY.Seller warrants that: (i) Buyer shall obtain good title to the product sold hereunder, (ii) at shipment such product shall conform to Seller’s specifications for the product; and (iii) the sale or use of such product will not infringe the claims of any U.S. patent covering the product itself, but Seller does not warrant against infringement which might arise by the use of said product in any combination with other products or arising in the operation of any process. SELLER MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, EVEN IF THAT PURPOSE IS KNOWN TO SELLER. ANY ADDITIONAL REPRESENTATIONS OR SUGGESTIONS REGARDING THE PRODUCT OR ITS POSSIBLE USES ARE BASED UPON SELLER’S GOOD FAITH OPINION AND BELIEF, BUT ARE NOT TO BE CONSTRUED AS AFFIRMATIONS OF FACT, PROMISES, OR DESCRIPTIONS, AND SHALL IN NO WAY BE DEEMED PART OF THE SALE OF PRODUCT. In particular, and without limiting the foregoing, because of environmental and use conditions beyond Seller’s control, Seller offers no warranty and makes no promise concerning the results that may be obtained by the Buyer (or the Buyer’s customer) with the product or the performance of the product. Each user should satisfy itself, by adequate testing, of the suitability of the product for its particular application.LIMITATION OF LIABILITY.(a) Seller’s total liability for any claim arising out of or in connection with this contract, including for breach of contract,warranty, statutory duty, or for other tort, including seller’s negligence, shall not exceed the purchase price of such product as to which such liability arises. Seller shall not be liable for any injury, loss or damage, resulting from the handling or use of the product shipped hereunder whether in the manufacturing process or otherwise. IN NO EVENT SHALL SELLER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES,INCLUDING WITHOUT LIMITATION LOSS OF PROFITS, CAPITAL OR BUSINESS OPPORTUNITY,DOWNTIME COSTS, OR CLAIMS OF CUSTOMERS OR EMPLOYEES OF BUYER, WHETHER IN AN ACTION UNDER CONTRACT, NEGLIGENCE OR ANY OTHER THEORY, ARISING OUT OF OR IN CONNECTION WITH THIS CONTRACT, OR THE USE, INABILITY TO USE, OR PERFORMANCE OF THE PRODUCT.(b) If Seller furnishes technical or other advice to Buyer, whether or not at Buyer’s request, with respect to processing,further manufacture, other use or resale of the products, Seller shall not be liable for, and Buyer assumes all risk of, such advice and the results thereof.The information provided is believed to be accurate at the time of preparation, or prepared from sources believed to be reliable, but it is the responsibility of user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine the suitability of the product for its intended use.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
环保溶剂EEP混酯
油漆油墨稀释剂好原料
一，EEP成分含量如下图所示（仅供参考）
上图所示说明该溶剂主要由EEP和PMA组成，总酯含量达99.53%；颜色水白色，水分和PH 值均达标；气味类似PMA无残留味；按馏程说明属于中高沸点低毒的环保溶剂；闪点55度。
二，作用：EEP混酯经大量的实验和客户体验，证明EEP混酯是生产涂料稀释剂和油墨稀释剂的好原料。
1，溶解力类似于CAC,PMA,由于沸点高于CAC，使得稀释剂在高温高湿条件下的涂装不易发白，实际证明比同等CAC剂量的稀释剂具有更好的抗白性。
2，具有更好的促进流平，防止高温高湿环境下的不良反应。
3，干性好，不会像DBE，DPMA，PGDA等那么难以实干。
4,性价比高，同比常规习惯使用的CAC,PMA成本大大降低。
佛山市顺德区零碳化工有限公司
20171122。