十字槽沉头自攻螺钉DIN7982ISO7050

五金螺丝标准标号

ISO2936 ISO4762 ISO4026 ISO4027 ISO4028 ISO4029
GB5782-86 ISO4014 GB5783-86 ISO4017 ISO2009 GB68-85 GB69-85 GB819-85 GB820-85 GB845-85 GB846-85 GB847-86
方头带垫关圆底端螺栓 T 型槽螺母单头螺柱地脚螺栓带槽圆螺母端面带孔圆螺母开槽平端紧定螺钉开槽锥端紧定螺钉六角螺母方螺母 -C 六角头螺钉六角头圆柱端紧定螺钉薄型方螺母 -B 六角头木螺钉吊环螺钉吊环螺母六角头螺栓大半圆头方颈螺栓（马车螺栓）沉头带插销马车螺栓沉头长方颈马车螺栓半圆头带插销马车螺栓沉头短方颈马车螺栓六角头精配螺栓（长螺纹）六角头精配螺栓（短螺栓）滚花平头螺钉半圆头铆钉沉头铆钉半沉头铆钉大扁头铆钉重型侧面带孔圆螺母侧面带孔圆螺母卡头 T 型槽螺钉双头螺柱（牙长 =2D ）内六角锥型闭锁螺钉内六角直型闭锁螺钉外六角锥型闭锁螺钉外六角直型闭锁螺钉薄型盲螺母开槽小圆柱头螺钉开槽大圆柱头螺钉
GB6171-86 ISO8673 Hexagon full nuts GB6172.1ISO4035 Hexagon thin nuts 86 GB6172-86 ISO4035 Hexagon thin nuts Slotted raised csk head wood GB101 screws GB99 Slotted round head wood screws Slotted countersunk head wood GB100 screws GB7245-87 Single coil spring lock washers Curved spring washers GB955 Wave spring washers GB37-88 T-head blots with square neck T-head bolts with double nip ISO8737 Taper pins with threaded end T-head bolts Wing nuts America form GB62-88 Wing nuts germany form Wing screws America form Wing screws germany form Ball knobs GB832-88 Slotted capstan screws ISO7435 Slotted set srews with full dog point GB75-85 Slotted set srews with chamfered ISO2342 GB73-85 end GB808-88 Pip nuts with thread GB856-88 External tap ISO7092 Washers for cheese head screws GB848-95 GB852-88 Square taper washers for GB852-88 Square taper washers for Square washers ISO7436 Slotted set with cup point GB74-85 GB6173-86 ISO8675 Hexagon thin nuts Rounds washers for wood ISO7094 constructions Sealing caps,push-in type GB798-88 Eye bolts form B Internal tab washers GB855-88 Washers with two taps GB834-88 Knurled thumb screws with collar Slotted knurled thumb screws with collar GB806-88 Knurled thumb nuts with collar GB807-88 Knurled thumb thin nuts Sealing washers Retaining rings for GB893-86 shafts(external),circlips Retaining rings for GB893.86 bores(internal),circlips Square head bolts with collar Square head bolts with half dog point

螺丝标准标号

ISO299 ISO299
GB799-88 GB817-76 GB815-88 GB73-85 GB71-85 GB39-88
方头带垫关圆底端螺栓 T 型槽螺母单头螺柱地脚螺栓带槽圆螺母端面带孔圆螺母开槽平端紧定螺钉开槽锥端紧定螺钉六角螺母方螺母 -C 六角头螺钉六角头圆柱端紧定螺钉薄型方螺母 -B 六角头木螺钉吊环螺钉吊环螺母六角头螺栓大半圆头方颈螺栓(马车螺栓) 沉头带插销马车螺栓沉头长方颈马车螺栓半圆头带插销马车螺栓沉头短方颈马车螺栓六角头精配螺栓(长螺纹) 六角头精配螺栓(短螺栓) 滚花平头螺钉半圆头铆钉沉头铆钉半沉头铆钉大扁头铆钉重型侧面带孔圆螺母侧面带孔圆螺母卡头 T 型槽螺钉双头螺柱(牙长 =2D ) 内六角锥型闭锁螺钉内六角直型闭锁螺钉外六角锥型闭锁螺钉外六角直型闭锁螺钉薄型盲螺母开槽小圆柱头螺钉开槽大圆柱头螺钉
德国标准 DINStandard DIN7504 DIN125-A DIN125-B DIN126 DIN127-A DIN127-B DIN911 DIN912 DIN913 DIN914 DIN915 DIN916 DIN931 DIN933 DIN963 DIN964 DIN965 DIN966 DIN7981 DIN7982 DIN7983 DIN7971 DIN7972 DIN7973 DIN7976 DIN7985 DIN7991 DIN982
金
螺丝标准英文品名号编国际标准中国标准
GBStandard GB15856.1-4 GB97.1-85 GB97.2-85 GB7244 GB93-87 GB70-85 GB77-85 GB78-85 GB79-85 GB80-85

紧固件标准对照

紧固件国标德标国际标准对应表螺丝标准及国标德标国际标准对应表中文品名德国标准中国标准国际标准英文品名自攻自钻螺钉多种头型DIN7504 GB15856.1-4 Self-drilling tapping screws平垫DIN125-A GB97.1-85 ISO7089 Plain washers平垫（带倒角）DIN125-B GB97.2-85 ISO7090 Mediun washers平垫DIN126 ISO7091 Plain washers重型弹垫DIN127-A GB7244 Spring lock washers,tang ends标准弹垫DIN127-B GB93-87 Spring lock washers,square ends内六角扳手DIN911 ISO2936 Socket wrenches内六角圆柱头螺钉DIN912 GB70-85 ISO4762 Hexagon socket cap screws内六角平端紧定螺钉DIN913 GB77-85 ISO4026 Hexagon socket set screws with falt point内六角尖端紧定螺钉DIN914 GB78-85 ISO4027 Hexagon socket set screws with cone point 内六角圆柱端紧定螺钉DIN915 GB79-85 ISO4028 Hexagon socket set screws with dog point 内六角凹端紧定螺钉DIN916 GB80-85 ISO4029 Hexagon socket set screws with cup point 六角头螺栓）（半牙）DIN931 GB5782-86 ISO4014 Hexagon head screws六角头螺栓（全牙）DIN933 GB5783-86 ISO4017 Hexagon head screws开槽沉头螺钉DIN963 GB68-85 ISO2009 Slotted countersund head screws开槽半沉头螺钉DIN964 GB69-85 ISO2010 Slotted raised countersunk oval head screws 十字槽沉头螺钉DIN965 GB819-85 ISO7046 Cross recessed countersunk head screws十字槽半沉头螺钉DIN966 GB820-85 ISO7047 Cross recessed raised十字槽盘头自攻螺攻DIN7981 GB845-85 ISO7049 Pan head tapping screws with cross recessed十字槽沉头自攻螺攻DIN7982 GB846-85 ISO7050Countersunk flat head tapping screws with crossrecessed十字槽半沉头自攻螺攻DIN7983 GB847-86 ISO7051Raised countersunk oval head tapping screws withcross开槽盘头自攻螺钉DIN7971 GB5282-85 ISO1481 Pan head tapping screws with slot开槽沉头自攻螺钉DIN7972 GB5283-85 ISO1482 countersunk flat head tapping screws with slot开槽半沉头自攻螺钉DIN7973 GB5284-85 ISO1483Raised sountersunk oval head tapping screws withslot六角头自攻螺钉DIN7976 GB5285-85 ISO1479 Hexagon tapping screws十字槽盘头螺钉DIN7985 GB818-85 ISO7045 Pan head screws with cross recessed内六角沉头螺钉DIN7991 ISO10642 Hexagon socket coutersunk head screws六角头尼龙锁紧螺母DIN982 GB812-88 ISO2982Prevailing rorque type hexagon nuts,heavytype,with nylon六角头薄型尼龙锁紧螺母DIN985 GB889.1-86 ISO7040Prevalling torque type hoxagon nuts,heavytype,with nylon六角盖型尼龙锁紧螺母DIN986 GB6172.2-86 ISO10511Preailling torque typedomed capnuts with nyloninsert六角头螺母（ 1 型）DIN934 GB6170-86 ISO4032 Hexagon full nuts细牙六角头螺母（ 1型）DIN934 GB6171-86 ISO8673 Hexagon full nuts六角头薄螺母DIN936 GB6172.1-86 ISO4035 Hexagon thin nuts六角薄螺母DIN439 GB6172-86 ISO4035 Hexagon thin nuts开槽半沉头木螺钉DIN95 GB101 Slotted raised csk head wood screws 开槽半圆头木螺钉DIN96 GB99 Slotted round head wood screws开槽沉头木螺钉DIN97 GB100 Slotted countersunk head wood screws 鞍形弹垫DIN128-A GB7245-87 Single coil spring lock washers弹簧止动垫圈DIN137-A Curved spring washers波形弹垫DIN137-B GB955 Wave spring washersT 型方颈螺栓DIN186 GB37-88 T-head blots with square neckT 型双接头螺栓DIN188 T-head bolts with double nip螺纹圆锥销DIN258 ISO8737 Taper pins with threaded endT 型头螺栓DIN261 T-head bolts蝶型螺母（美制）DIN315AF Wing nuts America form蝶型螺母（德制）DIN315DF GB62-88 Wing nuts germany form蝶型螺母（美制）DIN316AF Wing screws America form蝶型螺母DIN317DF Wing screws germany form（德制）圆球型盖型DIN319 Ball knobs螺母开槽带孔球DIN404 GB832-88 Slotted capstan screws面圆柱头蚴钉开槽长圆柱DIN417 GB75-85 ISO7435 Slotted set srews with full dog point端紧定螺钉开槽平端紧DIN427 GB73-85 ISO2342 Slotted set srews with chamfered end定螺钉（半牙）小六角特薄DIN431 GB808-88 Pip nuts with thread细牙螺母外舌止动垫DIN432 GB856-88 External tap圈小垫圈(用DIN433 GB848-95 ISO7092 Washers for cheese head screws于圆柱头螺钉)方斜垫圈DIN434 GB852-88 Square taper washers for（ U 型）方斜垫圈DIN435 GB852-88 Square taper washers for（ I 型）方垫圈DIN436 Square washers开槽凹端紧DIN438 GB74-85 ISO7436 Slotted set with cup point定螺钉细牙六角薄DIN439 GB6173-86 ISO8675 Hexagon thin nuts螺母木螺钉专用DIN440 ISO7094 Rounds washers for wood constructions垫圈密封帽DIN443 Sealing caps,push-in type活节螺栓 BDIN444 GB798-88 Eye bolts form B型内舌止动垫DIN462 Internal tab washers圈双耳止动垫DIN463 GB855-88 Washers with two taps圈滚花高头螺DIN464 GB834-88 Knurled thumb screws with collar钉开槽滚花高DIN465 Slotted knurled thumb screws with collar 头螺钉滚花高螺母DIN466 GB806-88 Knurled thumb nuts with collar滚花薄螺母DIN467 GB807-88 Knurled thumb thin nuts锁紧垫圈DIN470 Sealing washers轴用弹性垫DIN471 GB893-86 Retaining rings for shafts(external),circlips 圈孔用弹性垫DIN472 GB893.86 Retaining rings for bores(internal),circlips圈方头带垫螺DIN478 Square head bolts with collar栓方头圆柱底DIN479 Square head bolts with half dog point端螺栓方头带垫关DIN480 Square head bolts with collar,half dog point圆底端螺栓T 型槽螺母DIN508 ISO299 T-slot nuts单头螺柱DIN525 Single end studs地脚螺栓DIN529 GB799-88 Masonry bolts带槽圆螺母DIN546 GB817-76 Slotted round nuts端面带孔圆DIN547 GB815-88 Round nuts with drilled holes in one face螺母开槽平端紧DIN551 GB73-85 ISO4776 Slotted set screws with flat point定螺钉开槽锥端紧DIN553 GB71-85 ISO7434 Slotted set screws with cone point定螺钉六角螺母DIN555 ISO4034 Hexagon nuts方螺母 -C DIN557 GB39-88 Square nuts六角头螺钉DIN558 ISO4018 Hexagon screws六角头圆柱DIN561 Hexagon set screws with full dog point端紧定螺钉薄型方螺母DIN562 Square nuts without bevel-B六角头木螺DIN571 GB102-86 Hexgon head wood screw钉吊环螺钉DIN580 GB825-76 ISO3266 Lifting eye bolts吊环螺母DIN582 Lifting eye nuts六角头螺栓DIN601 ISO4016 Hexagon blots大半圆头方DIN603 GB14-88 ISO8677 Mushroom head square neck bolts(carriage bolts) 颈螺栓（马车螺栓）沉头带插销DIN604 Flat countersunk nib bolts马车螺栓沉头长方颈DIN605 Flat countersunk long squareneck bolts马车螺栓半圆头带插DIN607 Cup head nib bolts销马车螺栓沉头短方颈DIN608 Flat countersunk short square neck bolts马车螺栓六角头精配DIN609 Hexagon fitted bolts,long thread螺栓（长螺纹）六角头精配DIN610 Hexagon fitted bolts short thread螺栓（短螺栓）滚花平头螺DIN653 GB835-88 Knurled thumb screws thin type钉半圆头铆钉DIN660 GB867-86 ISO1051 Round head rivets沉头铆钉DIN661 GB869-86 ISO1051 Contersunk head rivets半沉头铆DIN662 ISO1051 Raised contersunk head rivets钉大扁头铆钉DIN674 ISO1051 Mushroom head rivets重型侧面带DIN703 Adjusting rings,heavy range(shafting collars) 孔圆螺母侧面带孔圆DIN705 GB816-88 Adjusting rings,light range(shafting collars) 螺母卡头DIN741 Wire rope clipsT 型槽螺钉DIN787 ISO299 T-slot screws双头螺柱DIN835 GB900-88 Studs-metal(end=2d)（牙长=2D ）内六角锥型DIN906 Hexagon socket pipe plugs,conical thread闭锁螺钉内六角直型DIN908 Thread闭锁螺钉外六角锥型DIN909 Thread闭锁螺钉外六角直型DIN910 Hexagon head screw plugs,cyl.thread闭锁螺钉薄型盲螺母DIN917 Hexagon cap nuts开槽小圆柱DIN920 Slotted short cheese head screws头螺钉开槽大圆柱DIN921 GB838-88 Slotted large cheese head screws头螺钉开槽圆柱头DIN923 GB830-88 Slotted pan head screw with shoulder轴肩螺钉开槽无头轴DIN927 Slotted shoulder screws肩螺钉焊接方螺母DIN928 GB/T13680-92 Square weld nuts焊接六角螺DIN929 GB/T13681-92 Hexagon weld nuts母六角头螺母DIN970 Hexagon nuts type-1六角头螺母DIN971 Hexagon nuts type-2细牙六角头DIN972 Hexagon nuts with fine thread螺母（ 2型）开槽六角螺DIN935 GB6178-86 ISO7035 Hexagon slotted and castle nuts母六角头开槽DIN937 GB6181-86 ISO7038 Hexagon thin slotted and caslte nuts薄螺母双头螺距DIN938 GB897-88 Studs metal(end=1d)（牙长=1D ）双头螺距DIN939 GB898-88 Studs metal(end=1.25d)（牙长=1.5D双头螺距DIN940 Studs metal(end=1.5d)（牙长=1.25D六角头细牙DIN960 GB5785-86 ISO8765 Hexagon head bolts,metric fine pitch thread螺栓（全牙）六角头细牙DIN961 GB8786-86 ISO8676 Hexagon head bolts,metric fine pitch thread螺栓（半牙）头部穿孔六DIN962 Additional shapes and versions for bolts角头螺栓牙条（全螺DIN975 GB6176-86 ISO8674 Threaded rods(studdings)纹）螺纹销DIN976 GB15389-94 Threaded pins(stud bolts)六角头开槽DIN979 Hexagon thin slotted and castle nuts薄螺母2 型全金属六角DIN980 Prevaillng rorque type hexagon nuts,all metal nuts 锁紧螺母 1型圆螺母DIN981 GB6184-86 ISO7199 Locknuts配合垫片DIN988 Shim rings木材连接用DIN1052 Washers for timber connectors垫片沉头钢钉DIN1151 Round plain head nails销钉专用垫DIN1440 ISO8738 Plain washers for clevis pins(A 型)片 A 型销钉专用垫DIN1441 Plain washers for clevis pins片带头销钉DIN1444 ISO2341 Clevis pins with head圆锥型槽销DIN1471 GB/T13829.2 ISO8744 Grooved pins,taper grooved圆锥型槽销DIN1472 GB/T13829.2 ISO8745 Grooved pins,taper grooved half length（半槽）平行槽销DIN1473 ISO8740 Grooved pins,parallel grooved full length（带倒角）前端凹槽槽DIN1474 ISO8741 Grooved pins,reverve grooved half length销中部凹槽槽DIN1475 ISO8742 Grooved pins,center grooved销圆头槽销DIN1476 ISO8746 Grooved pins with round head沉头槽销DIN1477 ISO8747 Grooved pins with countersunk head六角螺母棒DIN1479 Turnuckles(center parts),made out of hexagon bar花蓝螺栓DIN1480 Turnuckles with eye bolt and hook bolt弹性圆柱销DIN1481 GB879-86 ISO8752 Spring pins,heavy type组合式盖型螺母DIN1587 GB802-88 Hexagon domed cap nuts开槽圆螺母(配合沟头扳手)DIN1804 Slotted round nuts for hook spammer圆螺母（带插销孔）DIN1816 Round nuts with set holes盘型弹簧垫圈DIN2093 Disc springs喉箍DIN3017 Hose clamps润滑油嘴（旋扭头）DIN3404 Lubricating nipples,button head管夹DIN3567 Shackles for conduiltsU 型螺栓DIN3570 Stirrup bolts(U-bolts)球面垫圈DIN6319 GB849-88 Spherical washers,conical seats圆柱销DIN6325 ISO8734 Parallel pins厚六角螺母DIN6330 GB56-88 Hexagon nuts,1.5d厚六角法兰面螺母DIN6331 GB6177-86 Hexagon nuts,1.5d with collar长六角螺母DIN6334 Hexagon nuts,3d外齿锁紧垫圈DIN6797-A GB862.1-87 External teeth lock washers内齿锁紧垫圈DIN6797-I GB861.1-87 Internal teeth lock washers外锯齿锁紧垫圈DIN6798-A GB862.2-87 External teeth serrated lock washers内锯齿锁紧垫圈DIN6798-I GB861.2-87 Internal teeth serrated lock washers开口挡圈DIN6799 GB896-76 Retaining rings for shafts(E-rings),circlips 平键（ A型）DIN6885 ISO773/2491 Parallel keys(form A)半圆键DIN6888 ISO3912 Woodruff keys嵌环（支撑环）DIN6899 Thimbles机器螺钉和垫圈组合件DIN6900 Screws and washers assemblies自攻螺钉和垫圈组合件DIN6901 GB9074.1-17 Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉DIN6912 GB9074.18-23Hexagon cocket head cap screws with hole,lowhead大六角头螺栓DIN6914 Hexagon head bolts with large head大六角螺母DIN6915 Hexagon nuts with large wideth across flat大垫圈DIN6916 Round washers for friction grip bolts楔型方垫圈DIN6917 Spuare taper washers for friction grip bolts on T-六角法兰面螺母DIN6923 GB6187-86 ISO4161 Hexagon flange nuts全金属六角锁紧螺母 2 型DIN6925 GB6185.1-2000 ISO7042Prevailing torque type hexagon nuts,all metallicnuts轻型弹性圆柱销DIN7346 ISO13337 Spring pins,light type重型弹性圆柱销用垫圈DIN7349 Washers for bolts with heavy type spring pinss ISO 公制螺纹螺钉多种头型DIN7500 Thread forming screws for ISO-metric thread开槽切削螺纹螺钉（多种头型）DIN7513 Thread cutting screws十字槽切削螺纹螺钉（多种头型）DIN7516 Thread cutting screws cross recessT 型四爪螺母DIN7965 Tee nuts with pronge钢结构用六角头螺栓连接副DIN7968 GB1228/1229/1230 Hexagon head fitted bolts for steel structures圆柱头螺钉用弹簧垫圈DIN7980 ISO8738Spring lock washers for screws with cylindricalheads薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reducedhead钢结构用垫圈DIN7989 GB1230-84 Washers for steel structures钢结构用六角头螺栓DIN7990 GB1229-84 Hexagon head bolts for steel structures 轴用钢丝挡圈DIN7993 GB895.2-86 Roundwire snap rings for shafts十字槽半沉头木螺钉DIN7995 GB952-86Cross recessed raised countersunk head woodscrews十字槽圆头木螺钉DIN7996 GB950-86 Cross recessed round head wood screws十字槽沉头木螺钉DIN7997 GB951-86 Cross recessed countersunk head wood screws 螺纹护套DIN8140 Ciol inserts,coarse,fine thread,silf locking(普通、自锁等)大外径垫圈DIN9021 GB96-85 ISO7093 Washers,outside diameter appro.3d 弹簧卡子DIN11024 sping cotter for a bolt平板螺栓DIN13257 Belting bolts(elevator bolts)干壁钉（墙DIN18182 Dry wall screws板钉）环型螺母DIN28129 GB63-88 Lifting nuts(eye nuts)圆螺母用止DIN70952 Tab washer for slotted round nuts 退圆锥销DIN1 GB117 ISO2339 Taper pins圆柱销DIN7 GB119-86 ISO2339 Parallel pins开槽圆柱头DIN84 GB65-85 ISO1207 Slotted cheese head screws螺钉开槽盘头螺DIN85 GB67-85 ISO1580 Slotted pan head screws钉单耳止动垫DIN93 GB854 Tab washers圈开口销DIN94 GB91 ISO1234 Split cooter pins。

十字槽沉头自攻螺钉规格

十字槽沉头自攻螺钉规格
（实用版）
目录
1.十字槽沉头自攻螺钉的定义和结构
2.十字槽沉头自攻螺钉的规格
3.十字槽半沉头自攻螺钉的历史和发展
4.十字槽盘头自攻螺钉的类型和应用
5.十字槽盘头自攻螺钉的市场情况
正文
十字槽沉头自攻螺钉是一种常见的螺钉类型，它通常由金属螺丝线材墩打而成，成形后在搓牙，呈圆筒形，头部为平头，类似于一个环绕螺丝侧面的倾斜面，可以让螺丝紧锁在螺丝帽或其他物件上。

沉头螺丝的顶部直径较大，可以呈圆形或等六边形，便于使用螺丝起子等工具进行拧紧或拆卸。

十字槽沉头自攻螺钉的规格通常包括长度、直径、螺纹规格和头部形状等参数。

其中，长度和直径决定了螺钉的大小，螺纹规格则决定了螺钉的螺纹形状和尺寸，头部形状则决定了螺钉的使用场合和拧紧方式。

十字槽半沉头自攻螺钉是我国于 1985 年 8 月 1 日发布，1986 年6 月 1 日实施的一项标准，由我国机械工业联合会主管，全国紧固件标准化技术委员会归口。

这项标准的发布和实施，对于规范十字槽半沉头自攻螺钉的生产和应用，提高我国的紧固件行业水平起到了积极的作用。

十字槽盘头自攻螺钉是一种常见的十字槽螺钉类型，它通常由头部呈盘形的自攻螺钉和垫圈组成，具有安装方便、拧紧力矩大、可靠性高等优点，广泛应用于各种机械设备的连接和固定。

根据头部形状和螺纹规格的不同，十字槽盘头自攻螺钉可以分为多种类型，如大半圆头自攻螺钉、盘
头自攻螺钉和大垫圈组合件等。

十字槽盘头自攻螺钉的市场情况良好，需求量稳定，价格合理。

中德及国际标准螺丝标准对应表

序号中文品名德国标准DIN中国标准GB国际标准ISO英文品名1自攻自钻螺钉多种头型DIN7504GB15856.1-4Self-drilling tapping screws2平垫DIN125-A GB97.1-85ISO7089Plain washers3平垫（带倒角）DIN125-B GB97.2-85ISO7090Mediun washers4平垫DIN126ISO7091Plain washers5重型弹垫DIN127-A GB7244Spring lock washers,tang ends 6标准弹垫DIN127-B GB93-87Spring lock washers,square ends 7内六角扳手DIN911ISO2936Socket wrenches8内六角圆柱头螺钉DIN912GB70-85ISO4762Hexagon socket cap screws9内六角平端紧定螺钉DIN913GB77-85ISO4026Hexagon socket set screws with falt point10内六角尖端紧定螺钉DIN914GB78-85ISO4027Hexagon socket set screws with cone point11内六角圆柱端紧定螺钉DIN915GB79-85ISO4028Hexagon socket set screws with dog point12内六角凹端紧定螺钉DIN916GB80-85ISO4029Hexagon socket set screws with cup point13六角头螺栓）（半牙）DIN931GB5782-86ISO4014Hexagon head screws 14六角头螺栓（全牙）DIN933GB5783-86ISO4017Hexagon head screws15开槽沉头螺钉DIN963GB68-85ISO2009Slottedｃｏｕｎｔersund head screws16开槽半沉头螺钉DIN964GB69-85ISO2010Slotted raisedｃｏｕｎｔersunk oval head screws17十字槽沉头螺钉DIN965GB819-85ISO7046Cross recessedｃｏｕｎｔersunk head screws18十字槽半沉头螺钉DIN966GB820-85ISO7047Cross recessed raised19十字槽盘头自攻螺攻DIN7981GB845-85ISO7049Pan head tapping screws with cross recessed20十字槽沉头自攻螺攻DIN7982GB846-85ISO7050ｃｏｕｎｔersunk flat head tapping screws with cross21十字槽半沉头自攻螺攻DIN7983GB847-86ISO7051Raisedｃｏｕｎｔersunk oval head tapping screws with cross22开槽盘头自攻螺钉DIN7971GB5282-85ISO1481Pan head tapping screws with slot23开槽沉头自攻螺钉DIN7972GB5283-85ISO1482ｃｏｕｎｔersunk flat head tapping screws with slot24开槽半沉头自攻螺钉DIN7973GB5284-85ISO1483Raised sountersunk oval head tapping screws with slot25六角头自攻螺钉DIN7976GB5285-85ISO1479Hexagon tapping screws26十字槽盘头螺钉DIN7985GB818-85ISO7045Pan head screws with cross recessed27内六角沉头螺钉DIN7991ISO10642Hexagon socket coutersunk head screws28六角头尼龙锁紧螺母DIN982GB812-88ISO2982Prevailing rorque type hexagon nuts,heavy type,with nylon29六角头薄型尼龙锁紧螺母DIN985GB889.1-86ISO7040Prevalling torque type hoxagon nuts,heavy type,with nylon30六角盖型尼龙锁紧螺母DIN986GB6172.2-86ISO10511Preailling torque typedomed capnuts with nylonｉｎｓｅｒｔ中德螺丝标准对应表31六角头螺母（1型）DIN934GB6170-86ISO4032Hexagon full nuts 32细牙六角头螺母（1型）DIN934GB6171-86ISO8673Hexagon full nuts 33六角头薄螺母DIN936GB6172.1-86ISO4035Hexagon thin nuts 34六角薄螺母DIN439GB6172-86ISO4035Hexagon thin nuts35开槽半沉头木螺钉DIN95GB101Slotted raised csk head wood screws36开槽半圆头木螺钉DIN96GB99Slotted round head wood screws37开槽沉头木螺钉DIN97GB100Slottedｃｏｕｎｔersunk head wood screws38鞍形弹垫DIN128-A GB7245-87Single coil spring lock washers 39弹簧止动垫圈DIN137-A Curved spring washers40波形弹垫DIN137-B GB955Wave spring washers41T型方颈螺栓DIN186GB37-88T-head blots with square neck 42T型双接头螺栓DIN188T-head bolts with double nip43螺纹圆锥销DIN258ISO8737Taper pins with threaded end44T型头螺栓DIN261T-head bolts45蝶型螺母（美制）DIN315AF Wing nuts America form46蝶型螺母（德制）DIN315DF GB62-88Wing nuts germany form47蝶型螺母（美制）DIN316AF Wing screws America form48蝶型螺母（德制）DIN317DF Wing screws germany form49圆球型盖型螺母DIN319Ball knobs50开槽带孔球面圆柱头蚴钉DIN404GB832-88Slotted capstan screws51开槽长圆柱端紧定螺钉DIN417GB75-85ISO7435Slotted set srews with full dog point52开槽平端紧定螺钉（半牙）DIN427GB73-85ISO2342Slotted set srews with chamfered end53小六角特薄细牙螺母DIN431GB808-88Pip nuts with thread54外舌止动垫圈DIN432GB856-88External tap55小垫圈(用于圆柱头螺钉)DIN433GB848-95ISO7092Washers for cheese head screws 56方斜垫圈（U型）DIN434GB852-88Square taper washers for57方斜垫圈（I型）DIN435GB852-88Square taper washers for58方垫圈DIN436Square washers59开槽凹端紧定螺钉DIN438GB74-85ISO7436Slotted set with cup point60细牙六角薄螺母DIN439GB6173-86ISO8675Hexagon thin nuts61木螺钉专用垫圈DIN440ISO7094Rounds washers for wood constructions62密封帽DIN443Sealing caps,push-in type63活节螺栓B型DIN444GB798-88Eye bolts form B64内舌止动垫圈DIN462Internal tab washers65双耳止动垫圈DIN463GB855-88Washers with two taps66滚花高头螺钉DIN464GB834-88Knurled thumb screws with collar67开槽滚花高头螺钉DIN465Slotted knurled thumb screws with collar68滚花高螺母DIN466GB806-88Knurled thumb nuts with collar 69滚花薄螺母DIN467GB807-88Knurled thumb thin nuts70锁紧垫圈DIN470Sealing washers71轴用弹性垫圈DIN471GB893-86Retaining rings for shafts(external),circlips72孔用弹性垫圈DIN472GB893.86Retaining rings for bores(internal),circlips73方头带垫螺栓DIN478Square head bolts with collar74方头圆柱底端螺栓DIN479Square head bolts with half dog point75方头带垫关圆底端螺栓DIN480Square head bolts with collar,half dog point76T型槽螺母DIN508ISO299T-slot nuts77单头螺柱DIN525Single end studs 78地脚螺栓DIN529GB799-88Masonry bolts79带槽圆螺母DIN546GB817-76Slotted round nuts80端面带孔圆螺母DIN547GB815-88Round nuts with drilled holes in one face81开槽平端紧定螺钉DIN551GB73-85ISO4776Slotted set screws with flat point82开槽锥端紧定螺钉DIN553GB71-85ISO7434Slotted set screws with cone point83六角螺母DIN555ISO4034Hexagon nuts 84方螺母-C DIN557GB39-88Square nuts85六角头螺钉DIN558ISO4018Hexagon screws86六角头圆柱端紧定螺钉DIN561Hexagon set screws with full dog point87薄型方螺母-B DIN562Square nuts without bevel 88六角头木螺钉DIN571GB102-86Hexgon head wood screw89吊环螺钉DIN580GB825-76ISO3266Lifting eye bolts90吊环螺母DIN582Lifting eye nuts91六角头螺栓DIN601ISO4016Hexagon blots92大半圆头方颈螺栓（马车螺栓）DIN603GB14-88ISO8677Mushroom head square neckbolts(carriage bolts)93沉头带插销马车螺栓DIN604Flatｃｏｕｎｔersunk nib bolts94沉头长方颈马车螺栓DIN605Flatｃｏｕｎｔersunk long squareneck bolts95半圆头带插销马车螺栓DIN607Cup head nib bolts96沉头短方颈马车螺栓DIN608Flatｃｏｕｎｔersunk short square neck bolts97六角头精配螺栓（长螺纹）DIN609Hexagon fitted bolts,long thread 98六角头精配螺栓（短螺栓）DIN610Hexagon fitted bolts short thread 99滚花平头螺钉DIN653GB835-88Knurled thumb screws thin type 100半圆头铆钉DIN660GB867-86ISO1051Round head rivets101沉头铆钉DIN661GB869-86ISO1051Contersunk head rivets102半沉头铆钉DIN662ISO1051Raised contersunk head rivets103大扁头铆钉DIN674ISO1051Mushroom head rivets104重型侧面带孔圆螺母DIN703Adjusting rings,heavy range(shafting collars)105侧面带孔圆螺母DIN705GB816-88Adjusting rings,light range(shafting collars)106卡头DIN741Wire rope clips107T型槽螺钉DIN787ISO299T-slot screws108双头螺柱（牙长=2D）DIN835GB900-88Studs-metal(end=2d)109内六角锥型闭锁螺钉DIN906Hexagon socket pipe plugs,conical thread110内六角直型闭锁螺钉DIN908Thread 111外六角锥型闭锁螺钉DIN909Thread112外六角直型闭锁螺钉DIN910Hexagon head screw plugs,cyl.thread113薄型盲螺母DIN917Hexagon cap nuts114开槽小圆柱头螺钉DIN920Slotted short cheese head screws 115开槽大圆柱头螺钉DIN921GB838-88Slotted large cheese head screws116开槽圆柱头轴肩螺钉DIN923GB830-88Slotted pan head screw with shoulder117开槽无头轴肩螺钉DIN927Slotted shoulder screws118焊接方螺母DIN928GB/T13680-92Square weld nuts119焊接六角螺母DIN929GB/T13681-92Hexagon weld nuts120六角头螺母DIN970Hexagon nuts type-1121六角头螺母DIN971Hexagon nuts type-2122细牙六角头螺母（2型）DIN972Hexagon nuts with fine thread123开槽六角螺母DIN935GB6178-86ISO7035Hexagon slotted andｃａｓｔle nuts124六角头开槽薄螺母DIN937GB6181-86ISO7038Hexagon thin slotted and caslte nuts125双头螺距（牙长=1D）DIN938GB897-88Studs metal(end=1d) 126双头螺距（牙长=1.5D DIN939GB898-88Studs metal(end=1.25d)127双头螺距（牙长=1.25D DIN940Studs metal(end=1.5d)128六角头细牙螺栓（全牙）DIN960GB5785-86ISO8765Hexagon head bolts,metric fine pitch thread129六角头细牙螺栓（半牙）DIN961GB8786-86ISO8676Hexagon head bolts,metric fine pitch thread130头部穿孔六角头螺栓DIN962Additional shapes and versions for bolts131牙条（全螺纹）DIN975GB6176-86ISO8674Threaded rods(studdings) 132螺纹销DIN976GB15389-94Threaded pins(stud bolts)133六角头开槽薄螺母2型DIN979Hexagon thin slotted andｃａｓｔle nuts134全金属六角锁紧螺母1型DIN980Prevaillng rorque type hexagon nuts,all metal nuts135圆螺母DIN981GB6184-86ISO7199Locknuts136配合垫片DIN988Shim rings137木材连接用垫片DIN1052Washers for timber connectors 138沉头钢钉DIN1151Round plain head nails139销钉专用垫片A型DIN1440ISO8738Plain washers for clevis pins(A) 140销钉专用垫片DIN1441Plain washers for clevis pins 141带头销钉DIN1444ISO2341Clevis pins with head142圆锥型槽销DIN1471GB/T13829.2ISO8744Grooved pins,taper grooved143圆锥型槽销（半槽）DIN1472GB/T13829.2ISO8745Grooved pins,taper grooved half length144平行槽销（带倒角）DIN1473ISO8740Grooved pins,parallel grooved full length145前端凹槽槽销DIN1474ISO8741Grooved pins,reverve grooved half length146中部凹槽槽销DIN1475ISO8742Grooved pins,center grooved 147圆头槽销DIN1476ISO8746Grooved pins with round head148沉头槽销DIN1477ISO8747Grooved pins withｃｏｕｎｔersunk head149六角螺母棒DIN1479Turnuckles(center parts),made out of hexagon bar150花蓝螺栓DIN1480Turnuckles with eye bolt and hook bolt151弹性圆柱销DIN1481GB879-86ISO8752Spring pins,heavy type 152组合式盖型螺母DIN1587GB802-88Hexagon domed cap nuts153开槽圆螺母(配合沟头扳手)DIN1804Slotted round nuts for hook spammer154圆螺母（带插销孔）DIN1816Round nuts with set holes155盘型弹簧垫圈DIN2093Disc springs156喉箍DIN3017Hose clamps157润滑油嘴（旋扭头）DIN3404Lubricating nipples,button head 158管夹DIN3567Shackles for conduilts159U型螺栓DIN3570Stirrup bolts(U-bolts)160球面垫圈DIN6319GB849-88Spherical washers,conical seats 161圆柱销DIN6325ISO8734Parallel pins162厚六角螺母DIN6330GB56-88Hexagon nuts,1.5d163厚六角法兰面螺母DIN6331GB6177-86Hexagon nuts,1.5d with collar 164长六角螺母DIN6334Hexagon nuts,3d165外齿锁紧垫圈DIN6797-A GB862.1-87External teeth lock washers166内齿锁紧垫圈DIN6797-I GB861.1-87Internal teeth lock washers167外锯齿锁紧垫圈DIN6798-A GB862.2-87External teeth serrated lock washers168内锯齿锁紧垫圈DIN6798-I GB861.2-87Internal teeth serrated lock washers169开口挡圈DIN6799GB896-76Retaining rings for shafts(E-rings),circlips170平键（A型）DIN6885ISO773/2491Parallel keys(form A)171半圆键DIN6888ISO3912Woodruff keys172嵌环（支撑环）DIN6899Thimbles173机器螺钉和垫圈组合件DIN6900Screws and washers assemblies174自攻螺钉和垫圈组合件DIN6901GB9074.1-17Tapping screws and washer assemblies175薄型带孔内六角圆柱螺钉DIN6912GB9074.18-23Hexagon cocket head cap screwswith hole,low head176大六角头螺栓DIN6914Hexagon head bolts with large head177大六角螺母DIN6915Hexagon nuts with large wideth across flat178大垫圈DIN6916Round washers for friction grip bolts179楔型方垫圈DIN6917Spuare taper washers for friction grip bolts on T-180六角法兰面螺母DIN6923GB6187-86ISO4161Hexagon flange nuts181全金属六角锁紧螺母2型DIN6925GB6185.1-2000ISO7042Prevailing torque type hexagonnuts,all metallic nuts182轻型弹性圆柱销DIN7346ISO13337Spring pins,light type183重型弹性圆柱销用垫圈DIN7349Washers for bolts with heavy type spring pinss184ISO公制螺纹螺钉多种头型DIN7500Thread forming screws for ISO-metric thread185开槽切削螺纹螺钉（多种头型）DIN7513Thread cutting screws186十字槽切削螺纹螺钉（多种头型）DIN7516Thread cutting screws crossrecess187T型四爪螺母DIN7965Tee nuts with pronge188钢结构用六角头螺栓连接副DIN7968GB1228/1229/1230Hexagon head fitted bolts forsteel structures189圆柱头螺钉用弹簧垫圈DIN7980ISO8738Spring lock washers for screws with cylindrical heads190薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reduced head191钢结构用垫圈DIN7989GB1230-84Washers for steel structures192钢结构用六角头螺栓DIN7990GB1229-84Hexagon head bolts for steel structures193轴用钢丝挡圈DIN7993GB895.2-86Roundwire snap rings for shafts194十字槽半沉头木螺钉DIN7995GB952-86Cross recessed raisedｃｏｕｎｔersunk head wood screws195十字槽圆头木螺钉DIN7996GB950-86Cross recessed round head wood screws196十字槽沉头木螺钉DIN7997GB951-86Cross recessedｃｏｕｎｔersunk head wood screws197螺纹护套(普通、自锁等)DIN8140Ciolｉｎｓｅｒｔs,coarse,fine thread,silf locking198大外径垫圈DIN9021GB96-85ISO7093Washers,outside diameter appro.3d 199弹簧卡子DIN11024sping cotter for a bolt200平板螺栓DIN13257Belting bolts(elevator bolts)201干壁钉（墙板钉）DIN18182Dry wall screws202环型螺母DIN28129GB63-88Lifting nuts(eye nuts)203圆螺母用止退DIN70952Tab washer for slotted round nuts 204圆锥销DIN1GB117ISO2339Taper pins205圆柱销DIN7GB119-86ISO2339Parallel pins206开槽圆柱头螺钉DIN84GB65-85ISO1207Slotted cheese head screws207开槽盘头螺钉DIN85GB67-85ISO1580Slotted pan head screws208单耳止动垫圈DIN93GB854Tab washers209开口销DIN94GB91ISO1234ｓｐｌｉｔcooter pins。

十字槽沉头自攻螺钉规格

十字槽沉头自攻螺钉规格
十字槽沉头自攻螺钉的规格可以根据不同的需求和用途而有所不同。

以下是一些常见的十字槽沉头自攻螺钉规格的示例：
1. 直径（Diameter）：自攻螺钉的直径通常以英寸（inch）或毫米（mm）为单位来表示，常见的直径包括#4、#6、#8、#10、1/4英寸、5/16英寸等。

毫米规格通常以M开头，如M3、M4、M5、M6等。

2. 长度（Length）：自攻螺钉的长度通常以英寸或毫米表示，取决于螺钉的具体用途和安装深度。

常见的长度包括1/2英寸、3/4英寸、1英寸、1.5英寸、2英寸等。

毫米规格也有相应的长度，例如10mm、20mm、30mm等。

3. 螺纹类型（Thread Type）：自攻螺钉的螺纹类型可以根据用途不同而有所变化，常见的类型包括粗螺纹（Coarse Thread）和细螺纹（Fine Thread）。

4. 材料（Material）：自攻螺钉的材料通常包括钢、不锈钢、铜、铝等，具体的材料取决于用途和环境要求。

5. 钉头类型（Head Type）：自攻螺钉的钉头类型可以有许多种，
包括沉头（Flat Head）、圆头（Round Head）、锥头（Oval Head）等，选择取决于装饰性和应用场景。

6. 钉头的驱动类型：常见的驱动类型包括十字槽（Phillips）、印花（Pozi）、方头（Square）、六角（Hex）、六角瓦（Hex Washer）、六角弯曲（Hex Flange）等。

需要注意的是，选择自攻螺钉的规格应该根据具体的项目需求和安装情况来决定，以确保螺钉的性能和稳固度。

如果需要特定规格的自攻螺钉，建议咨询螺钉制造商或供应商，以获取最准确的信息和建议。

紧固件的国标德标国际标准号对应明细及其名称

紧固件的国标德标国际标准号对应明细及其名称螺丝标准编号中文品名德国标准中国标准国际标准英文品名自攻自钻螺钉多种头型 DIN7504 GB15856.1-4 Self-drilling tapping screws平垫 DIN125-A GB97.1-85 ISO7089 Plain washers平垫（带倒角） DIN125-B GB97.2-85 ISO7090 Mediun washers平垫 DIN126 ISO7091 Plain washers重型弹垫 DIN127-A GB7244 Spring lock washers,tang ends标准弹垫 DIN127-B GB93-87 Spring lock washers,square ends内六角扳手 DIN911 ISO2936 Socket wrenches内六角圆柱头螺钉 DIN912 GB70-85 ISO4762 Hexagon socket cap screws内六角平端紧定螺钉 DIN913 GB77-85 ISO4026 Hexagon socket set screws with falt point 内六角尖端紧定螺钉 DIN914 GB78-85 ISO4027 Hexagon socket set screws with cone point 内六角圆柱端紧定螺钉 DIN915 GB79-85 ISO4028 Hexagon socket set screws with dog point 内六角凹端紧定螺钉 DIN916 GB80-85 ISO4029 Hexagon socket set screws with cup point 六角头螺栓）（半牙） DIN931 GB5782-86 ISO4014 Hexagon head screws六角头螺栓（全牙） DIN933 GB5783-86 ISO4017 Hexagon head screws开槽沉头螺钉 DIN963 GB68-85 ISO2009 Slotted countersund head screws开槽半沉头螺钉 DIN964 GB69-85 ISO2010 Slotted raised countersunk oval head screws 十字槽沉头螺钉 DIN965 GB819-85 ISO7046 Cross recessed countersunk head screws十字槽半沉头螺钉 DIN966 GB820-85 ISO7047 Cross recessed raised十字槽盘头自攻螺攻 DIN7981 GB845-85 ISO7049 Pan head tapping screws with cross recessed十字槽沉头自攻螺攻 DIN7982 GB846-85 ISO7050 Countersunk flat head tapping screws with cross recessed十字槽半沉头自攻螺攻 DIN7983 GB847-86 ISO7051 Raised countersunk oval head tapping screws with cross开槽盘头自攻螺钉 DIN7971 GB5282-85 ISO1481 Pan head tapping screws with slot开槽沉头自攻螺钉 DIN7972 GB5283-85 ISO1482 countersunk flat head tapping screws with slot开槽半沉头自攻螺钉 DIN7973 GB5284-85 ISO1483 Raised sountersunk oval head tapping screws with slot六角头自攻螺钉 DIN7976 GB5285-85 ISO1479 Hexagon tapping screws十字槽盘头螺钉 DIN7985 GB818-85 ISO7045 Pan head screws with cross recessed 内六角沉头螺钉 DIN7991 ISO10642 Hexagon socket coutersunk head screws六角头尼龙锁紧螺母 DIN982 GB812-88 ISO2982 Prevailing rorque type hexagon nuts,heavy type,with nylon六角头薄型尼龙锁紧螺母 DIN985 GB889.1-86 ISO7040Prevalling torque type hoxagon nuts,heavytype,with nylon六角盖型尼龙锁紧螺母 DIN986 GB6172.2-86 ISO10511 Preailling torque typedomed capnuts with nylon insert六角头螺母（ 1 型） DIN934 GB6170-86 ISO4032 Hexagon full nuts 细牙六角头螺母（ 1 型）DIN934 GB6171-86 ISO8673 Hexagon full nuts 六角头薄螺母 DIN936 GB6172.1-86 ISO4035 Hexagon thin nuts六角薄螺母 DIN439 GB6172-86 ISO4035 Hexagon thin nuts开槽半沉头木螺钉 DIN95 GB101 Slotted raised csk head wood screws开槽半圆头木螺钉 DIN96 GB99 Slotted round head wood screws开槽沉头木螺钉 DIN97 GB100 Slotted countersunk head wood screws鞍形弹垫 DIN128-A GB7245-87 Single coil spring lock washers弹簧止动垫圈 DIN137-A Curved spring washers波形弹垫 DIN137-B GB955 Wave spring washersT 型方颈螺栓 DIN186 GB37-88 T-head blots with square neckT 型双接头螺栓 DIN188 T-head bolts with double nip螺纹圆锥销 DIN258 ISO8737 Taper pins with threaded endT 型头螺栓 DIN261 T-head bolts蝶型螺母（美制） DIN315AF Wing nuts America form蝶型螺母（德制） DIN315DF GB62-88 Wing nuts germany form蝶型螺母（美制） DIN316AF Wing screws America form蝶型螺母（德制） DIN317DF Wing screws germany form圆球型盖型螺母 DIN319 Ball knobs开槽带孔球面圆柱头蚴DIN404 GB832-88 Slotted capstan screws钉开槽长圆柱端紧定螺钉 DIN417 GB75-85 ISO7435 Slotted set srews with full dog point开槽平端紧定螺钉（半DIN427 GB73-85 ISO2342 Slotted set srews with chamfered end牙）小六角特薄细牙螺母 DIN431 GB808-88 Pip nuts with thread外舌止动垫圈 DIN432 GB856-88 External tap小垫圈(用于圆柱头螺DIN433 GB848-95 ISO7092 Washers for cheese head screws钉)方斜垫圈（ U 型） DIN434 GB852-88 Square taper washers for方斜垫圈（ I 型） DIN435 GB852-88 Square taper washers for方垫圈 DIN436 Square washers开槽凹端紧定螺钉 DIN438 GB74-85 ISO7436 Slotted set with cup point细牙六角薄螺母 DIN439 GB6173-86 ISO8675 Hexagon thin nuts木螺钉专用垫圈 DIN440 ISO7094 Rounds washers for wood constructions密封帽 DIN443 Sealing caps,push-in type活节螺栓 B 型 DIN444 GB798-88 Eye bolts form B内舌止动垫圈 DIN462 Internal tab washers双耳止动垫圈 DIN463 GB855-88 Washers with two taps滚花高头螺钉 DIN464 GB834-88 Knurled thumb screws with collar开槽滚花高头螺钉 DIN465 Slotted knurled thumb screws with collar滚花高螺母 DIN466 GB806-88 Knurled thumb nuts with collar滚花薄螺母 DIN467 GB807-88 Knurled thumb thin nuts锁紧垫圈 DIN470 Sealing washers轴用弹性垫圈 DIN471 GB893-86 Retaining rings for shafts(external),circlips 孔用弹性垫圈 DIN472 GB893.86 Retaining rings for bores(internal),circlips方头带垫螺栓 DIN478 Square head bolts with collar方头圆柱底端螺栓 DIN479 Square head bolts with half dog point方头带垫关圆底端螺栓 DIN480 Square head bolts with collar,half dog pointT 型槽螺母 DIN508 ISO299 T-slot nuts单头螺柱 DIN525 Single end studs地脚螺栓 DIN529 GB799-88 Masonry bolts带槽圆螺母 DIN546 GB817-76 Slotted round nuts端面带孔圆螺母 DIN547 GB815-88 Round nuts with drilled holes in one face开槽平端紧定螺钉 DIN551 GB73-85 ISO4776 Slotted set screws with flat point开槽锥端紧定螺钉 DIN553 GB71-85 ISO7434 Slotted set screws with cone point六角螺母 DIN555 ISO4034 Hexagon nuts方螺母 -C DIN557 GB39-88 Square nuts六角头螺钉 DIN558 ISO4018 Hexagon screws六角头圆柱端紧定螺钉 DIN561 Hexagon set screws with full dog point薄型方螺母 -B DIN562 Square nuts without bevel六角头木螺钉 DIN571 GB102-86 Hexgon head wood screw吊环螺钉 DIN580 GB825-76 ISO3266 Lifting eye bolts吊环螺母 DIN582 Lifting eye nuts六角头螺栓 DIN601 ISO4016 Hexagon blots大半圆头方颈螺栓（马车DIN603 GB14-88 ISO8677 Mushroom head square neck bolts(carriage bolts)螺栓）沉头带插销马车螺栓 DIN604 Flat countersunk nib bolts沉头长方颈马车螺栓 DIN605 Flat countersunk long squareneck bolts半圆头带插销马车螺栓 DIN607 Cup head nib bolts沉头短方颈马车螺栓 DIN608 Flat countersunk short square neck bolts六角头精配螺栓（长螺DIN609 Hexagon fitted bolts,long thread纹）六角头精配螺栓（短螺DIN610 Hexagon fitted bolts short thread栓）滚花平头螺钉 DIN653 GB835-88 Knurled thumb screws thin type半圆头铆钉 DIN660 GB867-86 ISO1051 Round head rivets沉头铆钉 DIN661 GB869-86 ISO1051 Contersunk head rivets半沉头铆钉 DIN662 ISO1051 Raised contersunk head rivets大扁头铆钉 DIN674 ISO1051 Mushroom head rivets重型侧面带孔圆螺母 DIN703 Adjusting rings,heavy range(shafting collars)侧面带孔圆螺母 DIN705 GB816-88 Adjusting rings,light range(shafting collars)卡头 DIN741 Wire rope clipsT 型槽螺钉 DIN787 ISO299 T-slot screws双头螺柱（牙长 =2D ） DIN835 GB900-88 Studs-metal(end=2d)内六角锥型闭锁螺钉 DIN906 Hexagon socket pipe plugs,conical thread内六角直型闭锁螺钉 DIN908 Thread外六角锥型闭锁螺钉 DIN909 Thread外六角直型闭锁螺钉 DIN910 Hexagon head screw plugs,cyl.thread薄型盲螺母 DIN917 Hexagon cap nuts开槽小圆柱头螺钉 DIN920 Slotted short cheese head screws开槽大圆柱头螺钉 DIN921 GB838-88 Slotted large cheese head screws开槽圆柱头轴肩螺钉 DIN923 GB830-88 Slotted pan head screw with shoulder开槽无头轴肩螺钉 DIN927 Slotted shoulder screws焊接方螺母 DIN928 GB/T13680-92 Square weld nuts焊接六角螺母 DIN929 GB/T13681-92 Hexagon weld nuts六角头螺母 DIN970 Hexagon nuts type-1六角头螺母 DIN971 Hexagon nuts type-2细牙六角头螺母（ 2 型）DIN972 Hexagon nuts with fine thread开槽六角螺母 DIN935 GB6178-86 ISO7035 Hexagon slotted and castle nuts六角头开槽薄螺母 DIN937 GB6181-86 ISO7038 Hexagon thin slotted and caslte nuts双头螺距（牙长 =1D ） DIN938 GB897-88 Studs metal(end=1d)双头螺距（牙长 =1.5D DIN939 GB898-88 Studs metal(end=1.25d)双头螺距（牙长 =1.25D DIN940 Studs metal(end=1.5d)六角头细牙螺栓（全牙）DIN960 GB5785-86 ISO8765 Hexagon head bolts,metric fine pitch thread 六角头细牙螺栓（半牙）DIN961 GB8786-86 ISO8676 Hexagon head bolts,metric fine pitch thread 头部穿孔六角头螺栓 DIN962 Additional shapes and versions for bolts 牙条（全螺纹） DIN975 GB6176-86 ISO8674 Threaded rods(studdings)螺纹销 DIN976 GB15389-94 Threaded pins(stud bolts)六角头开槽薄螺母2 型 DIN979 Hexagon thin slotted and castle nuts全金属六角锁紧螺母 1 型 DIN980Prevaillng rorque type hexagon nuts,all metalnuts圆螺母 DIN981 GB6184-86 ISO7199 Locknuts配合垫片 DIN988 Shim rings木材连接用垫片 DIN1052 Washers for timber connectors沉头钢钉 DIN1151 Round plain head nails销钉专用垫片 A 型 DIN1440 ISO8738 Plain washers for clevis pins(A 型 )销钉专用垫片 DIN1441 Plain washers for clevis pins带头销钉 DIN1444 ISO2341 Clevis pins with head圆锥型槽销 DIN1471 GB/T13829.2 ISO8744 Grooved pins,taper grooved圆锥型槽销（半槽） DIN1472 GB/T13829.2 ISO8745 Grooved pins,taper grooved half length平行槽销（带倒角） DIN1473 ISO8740 Grooved pins,parallel grooved full length 前端凹槽槽销 DIN1474 ISO8741 Grooved pins,reverve grooved half length 中部凹槽槽销 DIN1475 ISO8742 Grooved pins,center grooved圆头槽销 DIN1476 ISO8746 Grooved pins with round head沉头槽销 DIN1477 ISO8747 Grooved pins with countersunk head六角螺母棒 DIN1479 Turnuckles(center parts),made out of hexagon bar花蓝螺栓 DIN1480 Turnuckles with eye bolt and hook bolt 弹性圆柱销 DIN1481 GB879-86 ISO8752 Spring pins,heavy type组合式盖型螺母 DIN1587 GB802-88 Hexagon domed cap nuts开槽圆螺母(配合沟头扳手)DIN1804 Slotted round nuts for hook spammer圆螺母（带插销孔） DIN1816 Round nuts with set holes盘型弹簧垫圈 DIN2093 Disc springs喉箍 DIN3017 Hose clamps润滑油嘴（旋扭头） DIN3404 Lubricating nipples,button head管夹 DIN3567 Shackles for conduiltsU 型螺栓 DIN3570 Stirrup bolts(U-bolts)球面垫圈 DIN6319 GB849-88 Spherical washers,conical seats圆柱销 DIN6325 ISO8734 Parallel pins厚六角螺母 DIN6330 GB56-88 Hexagon nuts,1.5d厚六角法兰面螺母 DIN6331 GB6177-86 Hexagon nuts,1.5d with collar长六角螺母 DIN6334 Hexagon nuts,3d外齿锁紧垫圈 DIN6797-A GB862.1-87 External teeth lock washers内齿锁紧垫圈 DIN6797-I GB861.1-87 Internal teeth lock washers外锯齿锁紧垫圈 DIN6798-A GB862.2-87 External teeth serrated lock washers内锯齿锁紧垫圈 DIN6798-I GB861.2-87 Internal teeth serrated lock washers开口挡圈 DIN6799 GB896-76 Retaining rings for shafts(E-rings),circlips 平键（ A 型） DIN6885 ISO773/2491Parallel keys(form A)半圆键 DIN6888 ISO3912 Woodruff keys嵌环（支撑环） DIN6899 Thimbles机器螺钉和垫圈组合件 DIN6900 Screws and washers assemblies自攻螺钉和垫圈组合件 DIN6901 GB9074.1-17 Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉 DIN6912 GB9074.18-23Hexagon cocket head cap screws with hole,lowhead大六角头螺栓 DIN6914 Hexagon head bolts with large head大六角螺母 DIN6915 Hexagon nuts with large wideth across flat 大垫圈 DIN6916 Round washers for friction grip bolts楔型方垫圈 DIN6917 Spuare taper washers for friction grip bolts on T-六角法兰面螺母 DIN6923 GB6187-86 ISO4161 Hexagon flange nuts全金属六角锁紧螺母 2 型 DIN6925 GB6185.1-2000 ISO7042Prevailing torque type hexagon nuts,allmetallic nuts轻型弹性圆柱销 DIN7346 ISO13337 Spring pins,light type重型弹性圆柱销用垫圈 DIN7349 Washers for bolts with heavy type spring pinss ISO 公制螺纹螺钉多种头型DIN7500 Thread forming screws for ISO-metric thread 开槽切削螺纹螺钉（多种头型）DIN7513 Thread cutting screws十字槽切削螺纹螺钉（多种头型）DIN7516 Thread cutting screws cross recessT 型四爪螺母 DIN7965 Tee nuts with pronge钢结构用六角头螺栓连接副DIN7968 GB1228/1229/1230Hexagon head fitted bolts for steel structures圆柱头螺钉用弹簧垫圈 DIN7980 ISO8738 Spring lock washers for screws with cylindrical heads薄型内六角圆柱头螺钉 DIN7984 Hexagon socket head cap screws with,reduced head钢结构用垫圈 DIN7989 GB1230-84 Washers for steel structures钢结构用六角头螺栓 DIN7990 GB1229-84 Hexagon head bolts for steel structures 轴用钢丝挡圈 DIN7993 GB895.2-86 Roundwire snap rings for shafts十字槽半沉头木螺钉 DIN7995 GB952-86 Cross recessed raised countersunk head wood screws十字槽圆头木螺钉 DIN7996 GB950-86 Cross recessed round head wood screws十字槽沉头木螺钉 DIN7997 GB951-86 Cross recessed countersunk head wood screws 螺纹护套(普通、自锁等) DIN8140 Ciol inserts,coarse,fine thread,silf locking 大外径垫圈 DIN9021 GB96-85 ISO7093 Washers,outside diameter appro.3d弹簧卡子 DIN11024 sping cotter for a bolt平板螺栓 DIN13257 Belting bolts(elevator bolts)干壁钉（墙板钉） DIN18182 Dry wall screws环型螺母 DIN28129 GB63-88 Lifting nuts(eye nuts)圆螺母用止退 DIN70952 Tab washer for slotted round nuts圆锥销 DIN1 GB117 ISO2339 Taper pins圆柱销 DIN7 GB119-86 ISO2339 Parallel pins开槽圆柱头螺钉 DIN84 GB65-85 ISO1207 Slotted cheese head screws开槽盘头螺钉 DIN85 GB67-85 ISO1580 Slotted pan head screws单耳止动垫圈 DIN93 GB854 Tab washers开口销 DIN94 GB91 ISO1234 Split cooter pins。

中德及国际标准螺丝标准对应表

序号中文品名德国标准DIN中国标准GB国际标准ISO英文品名1自攻自钻螺钉多种头型DIN7504GB15856.1-4Self-drilling tapping screws2平垫DIN125-A GB97.1-85ISO7089Plain washers3平垫（带倒角）DIN125-B GB97.2-85ISO7090Mediun washers4平垫DIN126ISO7091Plain washers5重型弹垫DIN127-A GB7244Spring lock washers,tang ends 6标准弹垫DIN127-B GB93-87Spring lock washers,square ends 7内六角扳手DIN911ISO2936Socket wrenches8内六角圆柱头螺钉DIN912GB70-85ISO4762Hexagon socket cap screws9内六角平端紧定螺钉DIN913GB77-85ISO4026Hexagon socket set screws with falt point10内六角尖端紧定螺钉DIN914GB78-85ISO4027Hexagon socket set screws with cone point11内六角圆柱端紧定螺钉DIN915GB79-85ISO4028Hexagon socket set screws with dog point12内六角凹端紧定螺钉DIN916GB80-85ISO4029Hexagon socket set screws with cup point13六角头螺栓）（半牙）DIN931GB5782-86ISO4014Hexagon head screws 14六角头螺栓（全牙）DIN933GB5783-86ISO4017Hexagon head screws15开槽沉头螺钉DIN963GB68-85ISO2009Slottedｃｏｕｎｔersund head screws16开槽半沉头螺钉DIN964GB69-85ISO2010Slotted raisedｃｏｕｎｔersunk oval head screws17十字槽沉头螺钉DIN965GB819-85ISO7046Cross recessedｃｏｕｎｔersunk head screws18十字槽半沉头螺钉DIN966GB820-85ISO7047Cross recessed raised19十字槽盘头自攻螺攻DIN7981GB845-85ISO7049Pan head tapping screws with cross recessed20十字槽沉头自攻螺攻DIN7982GB846-85ISO7050ｃｏｕｎｔersunk flat head tapping screws with cross21十字槽半沉头自攻螺攻DIN7983GB847-86ISO7051Raisedｃｏｕｎｔersunk oval head tapping screws with cross22开槽盘头自攻螺钉DIN7971GB5282-85ISO1481Pan head tapping screws with slot23开槽沉头自攻螺钉DIN7972GB5283-85ISO1482ｃｏｕｎｔersunk flat head tapping screws with slot24开槽半沉头自攻螺钉DIN7973GB5284-85ISO1483Raised sountersunk oval head tapping screws with slot25六角头自攻螺钉DIN7976GB5285-85ISO1479Hexagon tapping screws26十字槽盘头螺钉DIN7985GB818-85ISO7045Pan head screws with cross recessed27内六角沉头螺钉DIN7991ISO10642Hexagon socket coutersunk head screws28六角头尼龙锁紧螺母DIN982GB812-88ISO2982Prevailing rorque type hexagon nuts,heavy type,with nylon29六角头薄型尼龙锁紧螺母DIN985GB889.1-86ISO7040Prevalling torque type hoxagon nuts,heavy type,with nylon30六角盖型尼龙锁紧螺母DIN986GB6172.2-86ISO10511Preailling torque typedomed capnuts with nylonｉｎｓｅｒｔ中德螺丝标准对应表31六角头螺母（1型）DIN934GB6170-86ISO4032Hexagon full nuts 32细牙六角头螺母（1型）DIN934GB6171-86ISO8673Hexagon full nuts 33六角头薄螺母DIN936GB6172.1-86ISO4035Hexagon thin nuts 34六角薄螺母DIN439GB6172-86ISO4035Hexagon thin nuts35开槽半沉头木螺钉DIN95GB101Slotted raised csk head wood screws36开槽半圆头木螺钉DIN96GB99Slotted round head wood screws37开槽沉头木螺钉DIN97GB100Slottedｃｏｕｎｔersunk head wood screws38鞍形弹垫DIN128-A GB7245-87Single coil spring lock washers 39弹簧止动垫圈DIN137-A Curved spring washers40波形弹垫DIN137-B GB955Wave spring washers41T型方颈螺栓DIN186GB37-88T-head blots with square neck 42T型双接头螺栓DIN188T-head bolts with double nip43螺纹圆锥销DIN258ISO8737Taper pins with threaded end44T型头螺栓DIN261T-head bolts45蝶型螺母（美制）DIN315AF Wing nuts America form46蝶型螺母（德制）DIN315DF GB62-88Wing nuts germany form47蝶型螺母（美制）DIN316AF Wing screws America form48蝶型螺母（德制）DIN317DF Wing screws germany form49圆球型盖型螺母DIN319Ball knobs50开槽带孔球面圆柱头蚴钉DIN404GB832-88Slotted capstan screws51开槽长圆柱端紧定螺钉DIN417GB75-85ISO7435Slotted set srews with full dog point52开槽平端紧定螺钉（半牙）DIN427GB73-85ISO2342Slotted set srews with chamfered end53小六角特薄细牙螺母DIN431GB808-88Pip nuts with thread54外舌止动垫圈DIN432GB856-88External tap55小垫圈(用于圆柱头螺钉)DIN433GB848-95ISO7092Washers for cheese head screws 56方斜垫圈（U型）DIN434GB852-88Square taper washers for57方斜垫圈（I型）DIN435GB852-88Square taper washers for58方垫圈DIN436Square washers59开槽凹端紧定螺钉DIN438GB74-85ISO7436Slotted set with cup point60细牙六角薄螺母DIN439GB6173-86ISO8675Hexagon thin nuts61木螺钉专用垫圈DIN440ISO7094Rounds washers for wood constructions62密封帽DIN443Sealing caps,push-in type63活节螺栓B型DIN444GB798-88Eye bolts form B64内舌止动垫圈DIN462Internal tab washers65双耳止动垫圈DIN463GB855-88Washers with two taps66滚花高头螺钉DIN464GB834-88Knurled thumb screws with collar67开槽滚花高头螺钉DIN465Slotted knurled thumb screws with collar68滚花高螺母DIN466GB806-88Knurled thumb nuts with collar 69滚花薄螺母DIN467GB807-88Knurled thumb thin nuts70锁紧垫圈DIN470Sealing washers71轴用弹性垫圈DIN471GB893-86Retaining rings for shafts(external),circlips72孔用弹性垫圈DIN472GB893.86Retaining rings for bores(internal),circlips73方头带垫螺栓DIN478Square head bolts with collar74方头圆柱底端螺栓DIN479Square head bolts with half dog point75方头带垫关圆底端螺栓DIN480Square head bolts with collar,half dog point76T型槽螺母DIN508ISO299T-slot nuts77单头螺柱DIN525Single end studs 78地脚螺栓DIN529GB799-88Masonry bolts79带槽圆螺母DIN546GB817-76Slotted round nuts80端面带孔圆螺母DIN547GB815-88Round nuts with drilled holes in one face81开槽平端紧定螺钉DIN551GB73-85ISO4776Slotted set screws with flat point82开槽锥端紧定螺钉DIN553GB71-85ISO7434Slotted set screws with cone point83六角螺母DIN555ISO4034Hexagon nuts 84方螺母-C DIN557GB39-88Square nuts85六角头螺钉DIN558ISO4018Hexagon screws86六角头圆柱端紧定螺钉DIN561Hexagon set screws with full dog point87薄型方螺母-B DIN562Square nuts without bevel 88六角头木螺钉DIN571GB102-86Hexgon head wood screw89吊环螺钉DIN580GB825-76ISO3266Lifting eye bolts90吊环螺母DIN582Lifting eye nuts91六角头螺栓DIN601ISO4016Hexagon blots92大半圆头方颈螺栓（马车螺栓）DIN603GB14-88ISO8677Mushroom head square neckbolts(carriage bolts)93沉头带插销马车螺栓DIN604Flatｃｏｕｎｔersunk nib bolts94沉头长方颈马车螺栓DIN605Flatｃｏｕｎｔersunk long squareneck bolts95半圆头带插销马车螺栓DIN607Cup head nib bolts96沉头短方颈马车螺栓DIN608Flatｃｏｕｎｔersunk short square neck bolts97六角头精配螺栓（长螺纹）DIN609Hexagon fitted bolts,long thread 98六角头精配螺栓（短螺栓）DIN610Hexagon fitted bolts short thread 99滚花平头螺钉DIN653GB835-88Knurled thumb screws thin type 100半圆头铆钉DIN660GB867-86ISO1051Round head rivets101沉头铆钉DIN661GB869-86ISO1051Contersunk head rivets102半沉头铆钉DIN662ISO1051Raised contersunk head rivets103大扁头铆钉DIN674ISO1051Mushroom head rivets104重型侧面带孔圆螺母DIN703Adjusting rings,heavy range(shafting collars)105侧面带孔圆螺母DIN705GB816-88Adjusting rings,light range(shafting collars)106卡头DIN741Wire rope clips107T型槽螺钉DIN787ISO299T-slot screws108双头螺柱（牙长=2D）DIN835GB900-88Studs-metal(end=2d)109内六角锥型闭锁螺钉DIN906Hexagon socket pipe plugs,conical thread110内六角直型闭锁螺钉DIN908Thread 111外六角锥型闭锁螺钉DIN909Thread112外六角直型闭锁螺钉DIN910Hexagon head screw plugs,cyl.thread113薄型盲螺母DIN917Hexagon cap nuts114开槽小圆柱头螺钉DIN920Slotted short cheese head screws 115开槽大圆柱头螺钉DIN921GB838-88Slotted large cheese head screws116开槽圆柱头轴肩螺钉DIN923GB830-88Slotted pan head screw with shoulder117开槽无头轴肩螺钉DIN927Slotted shoulder screws118焊接方螺母DIN928GB/T13680-92Square weld nuts119焊接六角螺母DIN929GB/T13681-92Hexagon weld nuts120六角头螺母DIN970Hexagon nuts type-1121六角头螺母DIN971Hexagon nuts type-2122细牙六角头螺母（2型）DIN972Hexagon nuts with fine thread123开槽六角螺母DIN935GB6178-86ISO7035Hexagon slotted andｃａｓｔle nuts124六角头开槽薄螺母DIN937GB6181-86ISO7038Hexagon thin slotted and caslte nuts125双头螺距（牙长=1D）DIN938GB897-88Studs metal(end=1d) 126双头螺距（牙长=1.5D DIN939GB898-88Studs metal(end=1.25d)127双头螺距（牙长=1.25D DIN940Studs metal(end=1.5d)128六角头细牙螺栓（全牙）DIN960GB5785-86ISO8765Hexagon head bolts,metric fine pitch thread129六角头细牙螺栓（半牙）DIN961GB8786-86ISO8676Hexagon head bolts,metric fine pitch thread130头部穿孔六角头螺栓DIN962Additional shapes and versions for bolts131牙条（全螺纹）DIN975GB6176-86ISO8674Threaded rods(studdings) 132螺纹销DIN976GB15389-94Threaded pins(stud bolts)133六角头开槽薄螺母2型DIN979Hexagon thin slotted andｃａｓｔle nuts134全金属六角锁紧螺母1型DIN980Prevaillng rorque type hexagon nuts,all metal nuts135圆螺母DIN981GB6184-86ISO7199Locknuts136配合垫片DIN988Shim rings137木材连接用垫片DIN1052Washers for timber connectors 138沉头钢钉DIN1151Round plain head nails139销钉专用垫片A型DIN1440ISO8738Plain washers for clevis pins(A) 140销钉专用垫片DIN1441Plain washers for clevis pins 141带头销钉DIN1444ISO2341Clevis pins with head142圆锥型槽销DIN1471GB/T13829.2ISO8744Grooved pins,taper grooved143圆锥型槽销（半槽）DIN1472GB/T13829.2ISO8745Grooved pins,taper grooved half length144平行槽销（带倒角）DIN1473ISO8740Grooved pins,parallel grooved full length145前端凹槽槽销DIN1474ISO8741Grooved pins,reverve grooved half length146中部凹槽槽销DIN1475ISO8742Grooved pins,center grooved 147圆头槽销DIN1476ISO8746Grooved pins with round head148沉头槽销DIN1477ISO8747Grooved pins withｃｏｕｎｔersunk head149六角螺母棒DIN1479Turnuckles(center parts),made out of hexagon bar150花蓝螺栓DIN1480Turnuckles with eye bolt and hook bolt151弹性圆柱销DIN1481GB879-86ISO8752Spring pins,heavy type 152组合式盖型螺母DIN1587GB802-88Hexagon domed cap nuts153开槽圆螺母(配合沟头扳手)DIN1804Slotted round nuts for hook spammer154圆螺母（带插销孔）DIN1816Round nuts with set holes155盘型弹簧垫圈DIN2093Disc springs156喉箍DIN3017Hose clamps157润滑油嘴（旋扭头）DIN3404Lubricating nipples,button head 158管夹DIN3567Shackles for conduilts159U型螺栓DIN3570Stirrup bolts(U-bolts)160球面垫圈DIN6319GB849-88Spherical washers,conical seats 161圆柱销DIN6325ISO8734Parallel pins162厚六角螺母DIN6330GB56-88Hexagon nuts,1.5d163厚六角法兰面螺母DIN6331GB6177-86Hexagon nuts,1.5d with collar 164长六角螺母DIN6334Hexagon nuts,3d165外齿锁紧垫圈DIN6797-A GB862.1-87External teeth lock washers166内齿锁紧垫圈DIN6797-I GB861.1-87Internal teeth lock washers167外锯齿锁紧垫圈DIN6798-A GB862.2-87External teeth serrated lock washers168内锯齿锁紧垫圈DIN6798-I GB861.2-87Internal teeth serrated lock washers169开口挡圈DIN6799GB896-76Retaining rings for shafts(E-rings),circlips170平键（A型）DIN6885ISO773/2491Parallel keys(form A)171半圆键DIN6888ISO3912Woodruff keys172嵌环（支撑环）DIN6899Thimbles173机器螺钉和垫圈组合件DIN6900Screws and washers assemblies174自攻螺钉和垫圈组合件DIN6901GB9074.1-17Tapping screws and washer assemblies175薄型带孔内六角圆柱螺钉DIN6912GB9074.18-23Hexagon cocket head cap screwswith hole,low head176大六角头螺栓DIN6914Hexagon head bolts with large head177大六角螺母DIN6915Hexagon nuts with large wideth across flat178大垫圈DIN6916Round washers for friction grip bolts179楔型方垫圈DIN6917Spuare taper washers for friction grip bolts on T-180六角法兰面螺母DIN6923GB6187-86ISO4161Hexagon flange nuts181全金属六角锁紧螺母2型DIN6925GB6185.1-2000ISO7042Prevailing torque type hexagonnuts,all metallic nuts182轻型弹性圆柱销DIN7346ISO13337Spring pins,light type183重型弹性圆柱销用垫圈DIN7349Washers for bolts with heavy type spring pinss184ISO公制螺纹螺钉多种头型DIN7500Thread forming screws for ISO-metric thread185开槽切削螺纹螺钉（多种头型）DIN7513Thread cutting screws186十字槽切削螺纹螺钉（多种头型）DIN7516Thread cutting screws crossrecess187T型四爪螺母DIN7965Tee nuts with pronge188钢结构用六角头螺栓连接副DIN7968GB1228/1229/1230Hexagon head fitted bolts forsteel structures189圆柱头螺钉用弹簧垫圈DIN7980ISO8738Spring lock washers for screws with cylindrical heads190薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reduced head191钢结构用垫圈DIN7989GB1230-84Washers for steel structures192钢结构用六角头螺栓DIN7990GB1229-84Hexagon head bolts for steel structures193轴用钢丝挡圈DIN7993GB895.2-86Roundwire snap rings for shafts194十字槽半沉头木螺钉DIN7995GB952-86Cross recessed raisedｃｏｕｎｔersunk head wood screws195十字槽圆头木螺钉DIN7996GB950-86Cross recessed round head wood screws196十字槽沉头木螺钉DIN7997GB951-86Cross recessedｃｏｕｎｔersunk head wood screws197螺纹护套(普通、自锁等)DIN8140Ciolｉｎｓｅｒｔs,coarse,fine thread,silf locking198大外径垫圈DIN9021GB96-85ISO7093Washers,outside diameter appro.3d 199弹簧卡子DIN11024sping cotter for a bolt200平板螺栓DIN13257Belting bolts(elevator bolts)201干壁钉（墙板钉）DIN18182Dry wall screws202环型螺母DIN28129GB63-88Lifting nuts(eye nuts)203圆螺母用止退DIN70952Tab washer for slotted round nuts 204圆锥销DIN1GB117ISO2339Taper pins205圆柱销DIN7GB119-86ISO2339Parallel pins206开槽圆柱头螺钉DIN84GB65-85ISO1207Slotted cheese head screws207开槽盘头螺钉DIN85GB67-85ISO1580Slotted pan head screws208单耳止动垫圈DIN93GB854Tab washers209开口销DIN94GB91ISO1234ｓｐｌｉｔcooter pins。