紧固件标准中英文对照表

1DIN1圆锥销taper pins ISO2339GB117 2DIN7圆柱销parallel pins ISO2338GB119-86 3DIN84开槽圆柱头螺钉slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈tab washers GB854 6DIN94开口销split cotter pins ISO1234GB91

7DIN95开槽半沉头木螺钉slotted raised csk head wood screws GB101 8DIN96开槽半圆头木螺钉slotted round head wood screws GB99

9DIN97开槽沉头木螺钉slotted countersunk head wood screws GB100 10DIN125-A平垫plain washers ISO7089GB97.1-85 11DIN125-B平垫(带倒角)mediun washers ISO7090GB97.2-85 12DIN126平垫plain washers ISO7091

13DIN127-A重型弹垫spring lock washers,tang ends GB7244 14DIN127-B标准弹垫spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈curved spring washers

17DIN137-B波形弹垫wave spring washers GB955 18DIN186T型方颈螺栓T-head bolts with square neck GB37-88 19DIN188T型双接头螺栓T-head bolts with double nip

20DIN258螺纹圆锥销taper pins with threaded end ISO8737

21DIN261T型头螺栓T-head bolts

22DIN315AF蝶型螺母(美制)wing nuts amercia form

23DIN315DF蝶型螺母(德制)wing nuts germany form GB62-88 24DIN316AF蝶型螺钉(美制)wing screws amercia form

25DIN317DF蝶型螺钉(德制)wing screws germany form

26DIN319圆球型盖型螺母ball knobs

27DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB832-88 28DIN417开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435GB75-85 29DIN427开槽平端紧定螺钉(半牙)slotted set srews with chamfered end ISO2342GB73-85 30DIN431小六角特薄细牙螺母pipe nuts with thread GB808-88 31DIN432外舌止动垫圈external tap GB856-88 32DIN433小垫圈(用于圆柱头螺钉)washers for cheese head screws ISO7092GB848-95 33DIN434方斜垫圈(U型)square taper washers for U-section GB852-88 34DIN435方斜垫圈(I型)square taper washers for I-sections GB852-88 35DIN436方垫圈square washers

36DIN438开槽凹端紧定螺钉slotted set with cup point ISO7436GB74-85 37DIN439六角薄螺母hexagon thin nuts ISO4035GB6172-86 38DIN439细牙六角薄螺母hexagon thin nuts ISO8675GB6173-86 39DIN440木螺钉专用垫圈rounds washers for wood constructions ISO7094

40DIN443密封帽sealing caps,push-in type

41DIN444活节螺栓B 型eye bolts form B GB798-88 42DIN462内舌止动垫圈internal tab washers

43DIN463双耳止动垫圈washers with two taps GB855-88

44DIN464滚花高头螺钉knurled thumb screws with collar GB834-88 45DIN465开槽滚花高头螺钉slotted knurled thumb screws with collar

46DIN466滚花高螺母knurled thumb nuts with collar GB806-88 47DIN467滚花薄螺母knurled thumb thin nuts GB807-88 48DIN470锁紧垫圈sealing washers

49DIN471轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-86 50DIN472孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-86 51DIN478方头带垫螺栓square head bolts with collar

52DIN479方头圆柱底端螺栓square head bolts with half dog point

53DIN480方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end

54DIN508T型槽螺母T-slot nuts ISO299

55DIN525单头螺柱single end studs

56DIN529地脚螺栓masonry bolts GB799-88 57DIN546带槽圆螺母slotted round nuts GB817-76 58DIN547端面带孔圆螺母round nuts with drilled holes in one face GB815-88 59DIN551开槽平端紧定螺钉slotted sit screws with flat point ISO4776GB73-85 60DIN553开槽锥端紧定螺钉slotted set screws with cone point ISO7434GB71-85 61DIN555六角螺母hexagon nuts ISO4034

62DIN557方螺母-C square nuts GB39-88 63DIN558六角头螺钉hexagon screws ISO4018

64DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point

65DIN562薄型方螺母-B square nuts without bevel(pressed nuts)

66DIN571六角头木螺钉hexagon head wood screws (coach screws)GB102-86 67DIN580吊环螺钉lifting eye bolts ISO3266GB825-76 68DIN582吊环螺母lifting eye nuts

69DIN601六角头螺栓hexagon bolts ISO4016

70DIN603大半圆头方颈螺栓(马车螺栓)mushroom head square neck bolts (carriage bolts)ISO8677GB14-88 71DIN604沉头带插销马车螺栓flat countersunk nib bolts

72DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts

73DIN607半圆头带插销马车螺栓cup head nib bolts

74DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts

75DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread

76DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread

77DIN653滚花平头螺钉knurled thumb screws thin type GB835-88 78DIN660半圆头铆钉round head rivets ISO1051GB867-86 79DIN661沉头铆钉contersunk head rivets ISO1051GB869-86 80DIN662半沉头铆钉raised contersunk head rivets ISO1051

81DIN674大扁头铆钉mushroom head rivets ISO1051

82DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)

83DIN705侧面带孔圆螺母adjusting rings,light range (shafting collars)GB816-88 84DIN741卡头wire rope clips

85DIN787T型槽螺钉T-slot screws ISO299

86DIN835双头螺柱（牙长=2D）studs-metal (end=2d)GB900-88

87DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread

88DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread

89DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread

90DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread

91DIN911内六角扳手socket wrenches ISO2936

92DIN912内六角圆柱头螺钉hexagon socket cap screws ISO4762GB70-85 93DIN913内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026GB77-85 94DIN914内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027GB78-85 95DIN915内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028GB79-85 96DIN916内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029GB80-85 97DIN917薄型盲螺母hexagon cap nuts

98DIN920开槽小圆柱头螺钉slotted short cheese head screws

99DIN921开槽大圆柱头螺钉slotted large cheese head screws GB838-88 100DIN923开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88 101DIN927开槽无头轴肩螺钉slotted shoulder screws

102DIN928焊接方螺母square weld nuts GB/T13680-92 103DIN929焊接六角螺母hexagon weld nuts GB/T13681-92 104DIN931六角头螺栓（半牙）hexagon head screws ISO4014GB5782-86 105DIN933六角头螺栓（全牙）hexagon head screws ISO4017GB5783-86 106DIN934六角头螺母(1型)hexagon full nuts ISO4032GB6170-86 107DIN934细牙六角头螺母(1型)hexagon full nuts ISO8673GB6171-86 108DIN935开槽六角螺母hexagon slotted and castle nuts ISO7035GB6178-86 109DIN936六角头薄螺母hexagon thin nuts ISO4035GB6172.1-86 110DIN937六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038GB6181-86 111DIN938双头螺距（牙长=1D）studs metal (end=1d)GB897-88 112DIN939双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88 113DIN940双头螺距（牙长=1.5D）studs metal (end=1.5d)

114DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765GB5785-86 115DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676GB5786-86 116DIN962头部穿孔六角头螺栓additional shapes and versions for bolts

117DIN963开槽沉头螺钉slotted countersund head screws ISO 2009GB68-85 118DIN964开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010GB69-85 119DIN965十字槽沉头螺钉cross recessed countersunk head screws ISO7046GB819-85 120DIN966十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047GB820-85 121DIN970六角头螺母hexagon nuts type-1

122DIN971六角头螺母hexagon nuts type-2

123DIN972细牙六角头螺母(2型)hexagon nuts with fine thread ISO8674GB6176-86 124DIN975牙条(全螺纹)threaded rods(studdings)GB15389-94 125DIN976螺纹销threaded pins(stud bolts)

126DIN979六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts

127DIN980全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199GB6184-86 128DIN981圆螺母locknuts ISO2982GB812-88 129DIN982六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040GB889.1-86

130DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511GB6172.2-86 131DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert

132DIN988配合垫片shim rings

133DIN1052木材连接用垫片washers for timber connectors

134DIN1151沉头钢钉round plain head nails

135DIN1440销钉专用垫片A型plain washers for clevis pins(A型)ISO8738

136DIN1441销钉专用垫片plain washers for clevis pins

137DIN1444带头销钉clevis pins with head ISO2341

138DIN1471圆锥型槽销grooved pins,taper grooved ISO8744GB/T13829.2 139DIN1472圆锥型槽销(半槽)grooved pins,taper grooved half length ISO8745GB/T13829.2 140DIN1473平行槽销(带倒角)grooved pins,parallel grooved full length ISO8740

141DIN1474前端凹槽槽销grooved pins,reserve grooved half length ISO8741

142DIN1475中部凹槽槽销grooved pins,centre grooved ISO8742

143DIN1476圆头槽销grooved pins with round head ISO8746GB/T13829.3 144DIN1477沉头槽销grooved pins with countersunk head ISO8747

145DIN1479六角螺母棒turnuckles(centre parts),made out of hexagon bar

146DIN1480花篮螺栓turnuckles with eye bolt and hook bolt

147DIN1481弹性圆柱销spring pins,heavy type ISO8752GB879-86 148DIN1587组合式盖型螺母hexagon domed cap nuts GB802-88 149DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner

150DIN1816圆螺母（带插销孔）round nuts with set holes

151DIN2093盘型弹簧垫圈disc springs

152DIN3017喉箍hose clamps

153DIN3404润滑油嘴（旋扭头）lubricating nipples,button head

154DIN3567管夹shackles for conduilts

155DIN3570U型螺栓stirrup bolts(U-bolts)

156DIN6319球面垫圈spherical washers,conical seats GB849-88 157DIN6325圆柱销parallel pins ISO8734

158DIN6330厚六角螺母hexagon nuts ,1.5d GB56-88 159DIN6331厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160DIN6334长六角螺母hexagon nuts ,3d

161DIN6797-A外齿锁紧垫圈external teeth lock washers GB862.1-87 162DIN6797-I内齿锁紧垫圈internal teeth lock washers GB861.1-87 163DIN6798-A外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87 164DIN6798-I内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87 165DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76 166DIN6885平键（A型）parallel keys(form A )ISO773/2491

167DIN6888半圆键woodruff keys ISO3912

168DIN6899嵌环（支撑环）thimbles

169DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17 170DIN6901自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head

172DIN6914大六角头螺栓hexagon head bolts with large head(friction grip bolts)

173DIN6915大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)

174DIN6916大垫圈round washers for friction grip bolts

175DIN6917楔型方垫圈spuare taper washers for friction grip bolts on T-sections

176DIN6923六角法兰面螺母hexagon flange nuts ISO4161GB6177-86 177DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042GB6185.1-2000 178DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618 179DIN7338扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86 180DIN7343螺旋夹紧销spiral pins ISO8750

181DIN7346轻型弹性圆柱销spring pins,light type ISO13337

182DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss

183DIN7500ISO公制螺纹螺钉(多种头型)threadforming screws for ISO-metric thread

184DIN7504自攻自钻螺钉(多种头型)self-drilling tapping screws

185DIN7513开槽切削螺纹螺钉(多种头型)thread cutting screws

186DIN7516十字槽切削螺纹螺钉(多种头型)thread cutting screws cross recess

187DIN7965T型四爪螺母tee nuts with pronge

188DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230 189DIN7971开槽盘头自攻螺钉pan head tapping screws with slot ISO1481GB5282-85 190DIN7972开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482GB5283-85 191DIN7973开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483GB5284-85 192DIN7976六角头自攻螺钉hexagon tapping screws ISO1479GB5285-85 193DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738

194DIN7981十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049GB845-85

195DIN7982十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050GB846-85

196DIN7983十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051GB847-86

197DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head

198DIN7985十字槽盘头螺钉pan head screws with cross recessed ISO7045GB818-85

199DIN7989钢结构用垫圈washers for steel structures GB1230-84 200DIN7990钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84 201DIN7991内六角沉头螺钉hexagon socket countersunk head screws ISO10642

202DIN7993轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86 203DIN7995十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86

204DIN7996十字槽圆头木螺钉cross recessed round head wood screws GB950-86

205DIN7997十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86

206DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking

207DIN9021大外径垫圈washers,outside diameter appro.3d ISO7093GB96-85

208DIN11024弹簧卡子spring cotter for a bolt

209DIN13257平板螺栓belting bolts (elevator bolts)

210DIN18182干壁钉（墙板钉）dry wall screws

211DIN28129环型螺母lifting nuts(eye nuts)GB63-88

212DIN70952圆螺母用止退垫圈tab washers for slotted round nuts GB858-88

管材管件阀门接头管道特件紧固件密封等中英文对照完整版

管材管件阀门接头管道特件紧固件密封等中英文对照集团标准化办公室：[VV986T-J682P28-JP266L8-68PNN]

管材、管件、阀门、接头、管道特件、紧固件、垫片、密封、工程材料等中英文对照化工管道设计技术英语词汇(1－2－3) 1管道组成件Pipingcomponent1.1管子Pipe管子(按照配管标准规格制造的)pipe管子(不按配管标准规格制造的其他用管)tube钢管steelpipe铸铁管castironpipe衬里管linedpipe复合管cladpipe碳钢管carbonsteelpipe合金钢管alloysteelpipe不锈钢stainlesssteelpipe奥氏体不锈钢管austeniticstainlesssteelpipe铁合金钢管ferriticalloysteelpipe轧制钢管wrought-steelpipe锻铁管wrought-ironpipe无缝钢管seamless(SMLS)steelpipe焊接钢管weldedsteelpipe电阻焊钢管electric-resistanceweldedsteelpipe电熔（弧）焊钢板卷管electric-fusion(arc)-weldedsteel-platepipe螺旋焊接钢管spiralweldedsteelpipe镀锌钢管galvanizedsteelpipe热轧无缝钢管hot-rollingseamlesspipe冷拔无缝钢管cold-drawingseamlesspipe水煤气钢管water-gassteelpipe塑料管plasticpipe玻璃管glasstube橡胶管rubbertube直管runpipe;straightpipe1.2管件Fitting弯头elbow异径弯头reducingelbow带支座弯头baseelbowk半径弯头longradiuselbow短半径弯头shortradiuselbow 长半径180°弯头longradiusreturn短半径180°弯头shortradiusreturn带侧向口的弯头（右向或左向）sideoutletelbow(righthandorlefthand)双支管弯头（形）doublebranchelbow三通tee异径三通reducingtee等径三通straighttee带侧向口的三通（右向或左向） sideoutlettee(righthandor1efthand)异径三通（分支口为异径） reducingtee(reducingonoutlet)异径三通（一个直通口为异径） reducingtee(reducingononerun)带支座三通basetee异径三通（一个直通口及分支口为异径）reducingtee(reducingononerunandoutlet)异径三通（两个直通口为异径，双头式）reducingtee(reducingonbothruns,bullhead)45°斜三通45°lateral45°斜三通（支管为异径）45°lateral(reducingonbranch)45°斜三通(一个直通口为异径)45°lateral(reducingononerun)45°斜三通(一个直通口及支管为异径)45°lateral(reducingononerunandbranch)Y型三通（俗称裤衩）true“Y”四通cross等径四通straightcross异径四通reducingcross异径四通（一个分支口为异径） reducingcross(reducingononeoutlet)异径四通（一个直通口及分支口为异径） reducingcross(reducingononerunandoutlet)异径四通（两个分支口为异径） reducingcross(reducingonbothoutlet)异径四通（一个直通口及两个分支口为异径）reducingcross(reducingononerunandbothoutlet)异径管reducer同心异径管concentricreducer偏心异径管eccentricreducer锻制异径管reducingswage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet 镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头 coupling,fullcoupling半管接头halfcoupling异径管接头reducingcoupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap(C)堵头plug短节nipple异径短节 reducingnipple;swagenipple1.3弯管Bend预制弯管fabricatedpipebend跨越弯管（^形）cross-overbend偏置弯管（~形）offsetbend90°弯管quarterbend环形弯管cirelebend单侧偏置90°弯管（形）singleoffsetquarterbendS形弯管“S”bend单侧偏置U形膨胀弯管（|形）singleoffset“U”bendU形弯管“U”bend双偏置U膨胀弯管doubleoffsetexpansion“U”bend 斜接弯管mitrebend三节斜接弯管3-piecemitrebend折皱弯管corrugatedbend圆度 roundness1.4法兰Flange(FLG）整体管法兰integralpipeflange钢管法兰steelpipeflange螺

紧固件中英文对照

最全紧固件中英文对照，外贸必备词典！一、紧固件 Fasteners 标准紧固件 Standard Fasteners 非标准紧固件 Nonstandard Fasteners 特殊紧固件 Special Fasteners 汽车紧固件 Automotive Fasteners 铜制紧固件 Brass Fasteners 航天用紧固件 Aerospace Fasteners 精密紧固件 Precision Fasteners 化学紧固件 Chemical Fasteners 摩托车紧固件 Motorcycle Fasteners 不锈钢紧固件 Stainless Steel Fasteners 铁道紧固件 Railway Fasteners 防松紧固件 Self-locking Fasteners 高强度紧固件 High strength Fasteners PEM紧固件 PEM Fasteners 钢结构紧固件 Steel Structural Fasteners 压铆紧固件 Self-Clinching Fasteners

铝制紧固件 Aluminum Fasteners 钛合金紧固件 Titanium Alloy Fasteners 尼龙紧固件 Nylon Fasteners 精制紧固件 Finished Fastener 粗制紧固件 Unfinished Fastener 螺纹紧固件 Threaded Fastener 半精制紧固件 Semi-Finished Fastener 抗剪紧固件 Shear Fastener 抗拉紧固件 Tension Fastener 面板紧固件 Panel Fasteners 二、螺栓 Bolts 六角头螺栓Hexagon Head Bolts 六角法兰面螺栓Hexagon Flange Bolts 轨道螺栓（鱼尾螺丝）Track Bolts 高强度螺栓 High Strength Bolts 地脚螺栓Eyelet Bolts 马车螺栓 Carriage Bolts 护拦螺栓 Guardrail Bots 焊接螺栓 Weld Bolts

德标、欧标、国际、国标标准件对照表

德标、欧标、国际、国标对照表 —— DIN EN ISO GB 对照表新德标旧德标英文名中文名国标 DIN EN ISO 4014 DIN 931-1 Hexagon head bolts - Product grades A and B(ISO 4014:1999) 六角头螺栓 GB/T 5782-2000 DIN EN ISO 4016 DIN 601 Hexagon head bolts - Product grade C(ISO 4016:1999) 六角头螺栓 C 级 GB/T 5780-2000 DIN EN ISO 4017 DIN 933 Hexagon head screws - Product grade A and B (ISO 4017:1999) 六角头螺栓全螺纹 GB/T 5783-2000 DIN EN ISO 4018 DIN 558 Hexagon head screws - Product grade C (ISO 4018:1999) 六角头螺栓全螺纹 C 级 GB/T 5781-2000 DIN EN ISO 8676 DIN 961 Hexagon head screws with metric fine pitch thread - Product grade A and B(ISO 8676:1999) 六角头螺栓细牙全螺纹 GB/T 5786-2000 DIN EN ISO 8765 DIN 960 Hexagon head bolts with fine pitch thread - Product grades A and B(ISO 8765:1999) 六角头螺栓细牙 GB/T 5785-2000 DIN EN ISO 4032 DIN 934 Hexagon nuts,style 1-Product grades A and B(ISO: 4032:1999) 1型六角螺母 GB/T 6170-2000 DIN EN ISO 4033 Hexagon nuts,style 2-Product grades A and B(ISO: 4033:1999) 2型六角螺母 GB/T 6175-2000 DIN EN ISO 4034 DIN 555 Hexagon nuts - Product grade C (ISO 4034:1999) 六角螺母 C 级 GB/T 41-2000 DIN EN ISO 4035 DIN 439-2 Hexagon thin nuts(chamfered)-Product grade A and B (ISO 4035:1999) 六角薄螺母 GB/T 6172.1-2000 DIN EN ISO 4036 DIN 439-1 Hexagon thin nuts - Product grade B(unchamfered)(ISO 4036:1999) 六角薄螺母无倒角 GB/T 6174-2000 DIN EN ISO 8673 DIN 934| DIN 971-1 Hexagon nuts,style 1,with metric fine pitch thread - Product grades A and B (ISO 8673:1999) 1型六角螺母细牙 GB/T 6171-2000 DIN EN ISO 8674 DIN 971-2 Hexagon nuts,style 2,with metric fine pitch thread - Product grades A and B (ISO 8674:1999) 2型六角螺母细牙 GB/T 6176-2000 DIN EN ISO 8675 DIN 439-2 Hexagon thin nuts with metric fine pitch thread - Product grades A and B (ISO 8675:1999) 六角薄螺母细牙 GB/T 6173-2000 DIN EN ISO 4762 DIN 912 Hexagon socket head cap screws(ISO 4762:1997) 内六角圆柱头螺钉 GB/T 70.1-2000 DIN EN ISO 7380 Hexagon socket button head sxrews (ISO 7380:1997) 内六角平圆头螺钉 GB/T 70.2-2000 DIN EN ISO 10642 DIN 7991 Hexagon socket countersunk head screws (ISO 10642:1997) 内六角沉头螺钉 GB/T 70.3-2000 DIN EN ISO 1207 DIN 84 Slotted cheese head screws-Product grade A(ISO 1207:1992) 开槽圆柱头螺钉 GB/T 65-2000

DIN GB标准件对照表

中德标准对照表序号Item 德国标准 DIN-Standard 中文品名 Description in Chinese 英文品名 Desciption in English 国际标准 ISO-Standard 中国标准 GB-Standard 1DIN1圆锥销Taper pins ISO2339GB117 2DIN7圆柱销Parallel pins ISO2339GB119-86 3DIN84开槽圆柱头螺钉 Slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉Slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈Tab washers GB854 6DIN94开口销Split cooter pins ISO1234GB91 7DIN95开槽半沉头木螺钉 Slotted raised csk head wood screws GB101 8DIN96开槽半圆头木螺钉 Slotted round head wood screws GB99 9DIN97开槽沉头木螺钉 Slotted countersunk head wood screws GB100 10DIN125-A平垫Plain washers ISO7089GB97.1-85 11DIN125-B平垫（带倒角）Mediun washers ISO7090GB97.2-85 12DIN126平垫Plain washers ISO7091 13DIN127-A重型弹垫Spring lock washers,tang ends GB7244 14DIN127-B标准弹垫Spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫Single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈Curved spring washers 17DIN137-B波形弹垫Wave spring washers GB955 18DIN186T型方颈螺栓T-head blots with square neck GB37-88 19DIN188T型双接头螺栓 T-head bolts with double nip 20DIN258螺纹圆锥销Taper pins with threaded end ISO8737 21DIN261T型头螺栓T-head bolts 22DIN315AF 蝶型螺母（美制） Wing nuts America form

(品质)(国内标准)紧固件GB大全以及美制英制德标对照表

紧固件规格标准——GB标准档圈锥销锁紧档圈GB883-86 螺钉锁紧档圈GB884-86 带锁圈的螺钉锁紧档圈GB885-86 轴肩档圈GB886-86 螺钉紧固轴端档圈GB891-86 螺栓紧固轴端档圈GB892-86 孔用弹性档圈-A型GB893.1-86 孔用弹性档圈-B型GB893.2-86 轴用弹性档圈-A型GB894.1-86 塑料滚花头螺钉GB840-88 开槽球面圆柱头轴位螺钉GB946-88 开槽球面大圆柱头螺钉GB947-88 开槽沉头不脱出螺钉GB948-88 开槽半沉头不脱出螺钉GB949-88 内六角花形盘头螺钉GB2672-86 内六角花形沉头螺钉GB2673-86 内六角花形半沉头螺钉GB2674-86 内六角圆柱头轴肩螺钉GB5281-85 内六角花形圆柱头螺钉-4.8级GB6190-86

轴用弹性档圈-B型GB894.2-86 孔用钢丝档圈GB895.1-86 轴用钢丝档圈GB895.2-86 开口档圈GB896-86 钢丝锁圈GB921-86 夹紧档圈GB960-86 自攻螺钉十字槽盘头自攻螺钉GB845-85 十字槽沉头自攻螺钉GB846-85 十字槽半沉头自攻螺钉GB847-85 开槽盘头自攻螺钉GB5282-85 内六角花形圆柱头螺钉-8.8和10.9级GB6191-86 精密机械用紧固件十字槽螺钉GB/T13806.1-92 十字槽半沉头螺钉GB/T820-2000 方头平端紧定螺钉GB821-88 十字槽圆柱头螺钉GB/T822-2000 十字槽小盘头螺钉GB823-88 吊环螺钉GB825-88 开槽盘头定位螺钉GB828-88 开槽圆柱端定位螺钉GB829-88 开槽圆柱头轴位螺钉GB830-88 开槽无头轴位螺钉GB831-88 开槽带孔球面圆柱头螺钉GB832-88

管材、管件、阀门、接头、管道特件、紧固件、密封等中英文对照

标准件中英文对照知识

常用钢材理论重量表 [2004-12-22 8:51:47] 计算公式： t（重量kg) = A(断面积mm²)×L(长度m) ×p(密度g/cm³) ×1/1000 注：(1) 型材制造中有允许偏差值，故上式只做估算之用。 (2) 关于p值,钢材通常取7.85 . 螺丝产品名称中英文对照（台湾版）螺丝螺 [2004-12-22 8:51:24] 六角螺絲(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角機械螺絲HEX HEAD MACHINE BOLTS 六角木牙螺絲HEX LAG BOLTS 四角螺絲SQUARE HEAD BOLTS T頭螺絲T HEAD BOLTS 馬車螺絲CARRIAGE BOLTS 環首螺絲EYE BOLTS 內六角孔螺絲HEX SOCKET CAP SCREWS 固定螺絲SET SCREWS 螺椿栓STUD BOLTS 螺旋椿SCREW STUDS 輪殼螺栓WHEEL BOLTS 翼形螺絲WING SCREWS 自攻螺絲SELF TAPPING SCREWS 自削螺絲THREAD CUTTING SCREWS 鑽尾螺絲SELF DRILLING SCREWS 旋入螺絲DRIVE SCREWS 機械螺絲MACHINE SCREWS 木螺絲WOOD SCREWS 家具螺絲FURNITURE SCREWS 塑板螺絲CHIPBOARD SCREWS 牆用螺絲DRYWALL SCREWS 基礎螺栓FOUNDATION BOLTS U型螺栓U BOLTS 勾頭螺栓HOOK BOLTS 套掛螺絲TOGGLE BOLTS 突緣螺絲FLANGE BOLTS 軌道螺栓(魚尾螺絲) TRACK BOLTS 耐候鋼螺絲CORTEN STEEL HEA VY HEX BOLTS 扭矩控制螺栓T.C.BOLTS

常用五金标准件名称-国家标准号对应表

常用五金标准件名称-国家标准号对应表新物料编码原物料编码名称全名规格型号标记 4105.00018 23.5080025 弹簧垫圈垫圈垫片_弹簧垫圈Φ2.5垫圈GB/T 93 2.5 4105.00011 23.2030006 弹簧垫圈垫圈垫片_弹簧垫圈φ3（镀黑锌）垫圈GB/T 93 3 A23.2030010 23.2030010 弹簧垫圈垫圈垫片_弹簧垫圈φ3（镀彩锌）垫圈GB/T 93 3 4105.00015 23.2040008 弹簧垫圈垫圈垫片_弹簧垫圈φ4（镀黑锌）垫圈GB/T 93 4 4105.00014 23.2040006 弹簧垫圈垫圈垫片_弹簧垫圈φ4垫圈GB/T 93 4 4105.00025 23.2050006 弹簧垫圈垫圈垫片_弹簧垫圈φ5垫圈GB/T 93 5 4105.00016 23.2060006 弹簧垫圈垫圈垫片_弹簧垫圈φ6（镀黑锌）垫圈GB/T 93 6 4105.00017 23.2080006 弹簧垫圈垫圈垫片_弹簧垫圈Φ8垫圈GB/T 93 8 4105.00020 28.8009114 垫片垫圈垫片_垫片D型垫片Φ6.5 VT8.009.114 非标件 A28.8602779 28.8602779 垫片机加件_垫片VT8.602.779 非标件 A28.8602780 28.8602780 垫片机加件_垫片VT8.602.780 非标件 4201.00041 23.1041819 垫圈垫圈垫片_垫圈VT8.078.433(φ4.5*19*1.5MM 装灯泡用）非标件 4105.00019 23.5090025 平垫垫圈垫片_平垫Φ2.5垫圈GB/T95 2.5 4105.00001 23.1030001 平垫圈垫圈垫片_平垫圈φ3（镀黑锌）垫圈GB/T95 3 4105.00003 23.1030006 垫圈垫圈垫片_垫圈Φ 3（镀彩锌）垫圈GB/T95 3 4105.00005 23.1040006 平垫圈垫圈垫片_平垫圈φ4（黑）垫圈GB/T95 4 A23.1040007 23.1040007 平垫圈垫圈垫片_平垫圈φ4（镀彩锌）垫圈GB/T95 4 A23.2000005 23.2000005 垫片垫圈垫片_垫片Φ5垫圈GB/T95 5 4105.00006 23.1061216 平垫圈垫圈垫片_平垫圈φ6（镀黑锌）垫圈GB/T95 6 4105.00009 23.1080006 平垫圈垫圈垫片_平垫圈φ8（镀黑锌）垫圈GB/T95 8 A23.1100006 23.1100006 垫圈垫圈垫片_垫圈φ12垫圈GB/T95 12 4105.00007 23.1061816 大平垫垫圈垫片_大平垫φ6x18垫圈GB/T 96.2 6 4105.00004 23.1030007 平垫圈垫圈垫片_平垫圈Ф3 镀彩锌外径9mm 垫圈GB/T 96.2 3 4105.00002 23.1030002 平垫圈垫圈垫片_平垫圈φ3（镀黑锌）垫圈GB/T97.1 3 第 2 页共 10

haso标准件中英文对照

HASCO Z标准件系列 Z00 导柱Guide pillar Z01 导柱Guide pillar Z011 导柱Guide pillar Z012 导柱Guide pillar Z013 导柱Guide pillar Z014 导柱Guide pillar Z0141 导柱连接端End piece Z0142 导柱连接端End piece Z015 导柱Guide pillar Z0151 导柱连接端(Z015/…专用)Pillar adapter Z0152 导柱连接端Pillar adapter Z02 顶杆Ejector rod Z022 导管Guide sleeve Z03 导柱Guide pillar Z05 圆锥形管精定位Locating unit, round Z055 圆形垫片Spacer Z056 圆形垫件Spacer Z06 平锥形导块Locating unit Z07 长方形导块Square guide bar Z08 直身方形管位导块Pre-centering unit Z081 方形垫片Spacer disc Z091 方形定位锁块(公)Square interlock Z092 方形定位锁块(母)Square interlock Z093 方形定位锁块(母)Square interlock Z10 导套Guide bush Z10W 自润滑导套Guide bush Z11 导套Guide bush Z11W 自润滑导套Guide bush Z12 滚珠导套Ball guide bush Z13W 自润滑导套Self lubric.Guide bush Z15W 自润滑垫片Self lubric. Flat stock Z16W 自润滑垫片Self lubric. Guide rail Z17 长方形导块(Z07/...专用)Guide retainer Z20 定板导套Centering sleeve Z25 定位销Dowel pin Z26 定位销Dowel pin Z28 六角螺母Hexagon nut Z281 六角螺母Hexagon nut Z282 六角螺母Hexagon nut Z285 螺母Nut for T-slots Z286 螺母Nut for T-slots Z30 胚头内六角螺丝Socket head cap screw

常用紧固件采购规范

表单编号：****

图1 六角头螺栓基本尺寸标记代号常见螺母基本尺寸标注代号（如下图2）及其含义：图中：e:对角宽度； D:螺纹基本大径（公称直径）； m:螺母高度； m':扳拧高度； s:对边宽度。图2 六角螺母尺寸标记代号常见螺纹标记示例及其含义（如下图3）：图3 普通螺纹标记示例及其含义

各标准关于产品尺寸标注有不同要求，以国标GB/T 1237-2000为例，规定如下：完整标记：紧固件的完整标记形式如下图4：图4 紧固件完整标记标记简化原则： .1类别（名称）标准年代号及其前面的“-”允许全部或部分省略。年代号的标准应以现行标准为准。 .2标记中的“-”允许全部或部分省略；标记中“其他直径或特性”前面的“×”允许省略。但省略后不应导致对标记的误解，一般以空格代替。 .3当产品标准中只规定一种产品型式、性能等级或硬度或材料、产品等级、扳拧型式及表面处理时，允许全部或部分省略。 .4当产品标准中规定两种及其以上的产品型式、性能等级或硬度或材料、产品等级、扳拧型式及表面处理时，应规定可以省略其中的一种，并在产品标准的标记示例中给出省略后的简化标记。标记示例：外螺纹件： .1螺纹规格d=M12、公称长度l=80mm、性能等级为级、表面氧化、产品等级为A级的六角头螺栓的标记：螺栓 GB/T 5782—2000-M12× (完整标记) .2螺纹规格d=M12、公称长度l=80mm、性能等级为级、表面氧化、产品等级为A级、的六角头螺栓的标记：螺栓 GB/T 5782 M12×80 (简化标记) .3螺纹规格d=M6、公称长度l=6mm、长度z=4mm、性能等级为33H级、表面氧化的开槽盘头定位螺钉的标记：螺钉 GB/T 828—1988-M6×6×4-33H-O (完整标记) .4螺纹规格D=M6、公称长度l=6mm、长度z=4mm、性能等级为14H级不经表面处理的开槽盘头定位螺钉的标记：螺钉 GB/T 828 M6×6×4 (简化标记) 内螺纹件：

齿轮术语中英文对照表

中间齿轮intermediate gear(counter gear) 副轴齿轮counter shaft gear 副轴counter shaft 变速器输入轴transmission imput shaft 变速器输出轴transmission output shaft 变速器主动齿轮轴transmission drive gear shaft 变速器主轴transmission main shaft 变速器中间轴transmission countershaft 变速器轴的刚度rigidity of shaft 变速齿轮比(变速比)transmission gear ratio 传动比gear ratio 主压力line pressure 调制压力modulated pressure 真空调制压力vacuum modulator pressure 速控压力governor pressure 缓冲压力compensator or trimmer pressure 限档压力hold presure 前油泵front pump (input pump ) 液力传动装置充油压力hydrodynamic unit change pressure 后油泵gear pump (output pump ) 回油泵scavenge oil pump 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety 安全载荷safe load 变形deformation 摆线齿轮cycloidal gear 摆线齿形cycloidal tooth profile 背锥角back angle 背锥距back cone distance 比例尺scale 变速speed change 变速齿轮change gear ; change wheel 变位齿轮modified gear 变位系数modification coefficient 标准齿轮standard gear 标准直齿轮standard spur gear 表面粗糙度surface roughness 不完全齿轮机构intermittent gearing 补偿compensation 参数化设计parameterization design, PD 残余应力residual stress 操纵及控制装置operation control device 槽数Geneva numerate 侧隙backlash 差动轮系differential gear train 差动螺旋机构differential screw mechanism 差速器differential 常用机构conventional mechanism; mechanism in common use 承载量系数bearing capacity factor 承载能力bearing capacity 成对安装paired mounting 尺寸系列dimension series 齿槽tooth space 齿槽宽spacewidth 齿侧间隙backlash 齿顶高addendum 齿顶圆addendum circle 齿根高dedendum 齿根圆dedendum circle 齿厚tooth thickness 齿距circular pitch 齿宽face width 齿廓tooth profile 齿廓曲线tooth curve 齿轮gear 齿轮变速箱speed-changing gear boxes 齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped

紧固件中英文对照精华

序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 1DIN1圆锥销taper pins ISO2339GB117 2DIN7圆柱销parallel pins ISO2338GB119-86 3DIN84开槽圆柱头螺钉slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈tab washers GB854 6DIN94开口销split cotter pins ISO1234GB91 7DIN95开槽半沉头木螺钉slotted raised csk head wood screws GB101 8DIN96开槽半圆头木螺钉slotted round head wood screws GB99 9DIN97开槽沉头木螺钉slotted countersunk head wood screws GB100 10DIN125-A平垫plain washers ISO7089GB97.1-85 11DIN125-B平垫(带倒角）mediun washers ISO7090GB97.2-85 12DIN126平垫plain washers ISO7091 13DIN127-A重型弹垫spring lock washers,tang ends GB7244 14DIN127-B标准弹垫spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈curved spring washers 17DIN137-B波形弹垫wave spring washers GB955 18DIN186T型方颈螺栓T-head bolts with square neck GB37-88 19DIN188T型双接头螺栓T-head bolts with double nip 20DIN258螺纹圆锥销taper pins with threaded end ISO8737 21DIN261T型头螺栓T-head bolts 22DIN315AF蝶型螺母(美制）wing nuts amercia form 23DIN315DF蝶型螺母(德制）wing nuts germany form GB62-88 24DIN316AF蝶型螺钉(美制）wing screws amercia form 25DIN317DF蝶型螺钉(德制）wing screws germany form 德国标准和国际标准、中国标准中英文对照表

供应商选择和管理程序-中英文对照

————————————————————————————————作者：————————————————————————————————日期：

XXX Supplier Selection and Management Procedure 供应商选择和管理程序 Checked by/校准：Approved by/批准：Doc. No./文件编号：Ver. No./版本号：

XXX Checked by/校准： Approved by/批准： Doc. No./文件编号： Ver. No./版本号： Audit and Approval 审核及批准 Audit and Approval 审核及批准 Signature 签字 Date 日期 Remark 备注 General Manager 总经理 √ Production Dept 制造部 √ R&D Dept. 产品开发部 √ Quality Dept. 质量部 √ Purchasing Dept. 采购部 √ Finance Dept. 财务部 √ HR Dept. 人力资源部 Sales Dept. 销售部

XXX 1 Purpose 目的： To define the methodology to select, assess, approve new suppliers and manage supplier to ensure uniformity across the group and that all purchased product conforms to the purchase requirements of NAILI. 定义如何选择、评估、批准和管理供应商。 2 Scope 范围： All parts and services contribute to products that sold to Customers including Raw material, Subcontracting parts, Services and Other Products. 所有作用于销售给客户产品的原材料、零部件和服务，包括外包合同、零件、服务和其他的产品。 3 Definition定义： None 无 4. Responsibility职责: Purchasing department is responsible for sourcing, preliminarily assessing, recommending, auditing, manage new suppliers and steer price determination. 采购部负责寻找,初评,推荐,审核,管理供应商及跟进价格确认流程。 R&D department is responsible for audit new suppliers to confirm their technical capability. 产品开发部负责审核新供应商以确认其技术能力. Quality department is responsible for preliminarily assessing, audit new suppliers to confirm their quality assurance capability and incoming control。质量部负责初评,审核新供应商,确认其品质保证能力及来料控制. 5. Procedure内容: 5.1 New supplier development 5.1.1 Sourcing for new supplier寻找新供应商 5.1.1.1Purchasing department gets purchasing request and needs for new supplier. All departments can request a need. 采购部得到采购需求，需要发展新供应商。公司任何部门都可以提出采购需求。Checked by/校准：Approved by/批准：Doc. No./文件编号：Ver. No./版本号：

最全紧固件中英文对照

最全緊固件中英文對照，外貿必備詞典！一、緊固件 Fasteners 標準緊固件 Standard Fasteners 非標準緊固件 Nonstandard Fasteners 特殊緊固件 Special Fasteners 汽車緊固件 Automotive Fasteners 銅制緊固件 Brass Fasteners 航天用緊固件 Aerospace Fasteners 精密緊固件 Precision Fasteners 化學緊固件 Chemical Fasteners 摩托車緊固件 Motorcycle Fasteners 不銹鋼緊固件 Stainless Steel Fasteners 鐵道緊固件 Railway Fasteners 防松緊固件 Self-locking Fasteners 高強度緊固件 High strength Fasteners PEM緊固件 PEM Fasteners 鋼結構緊固件 Steel Structural Fasteners 壓鉚緊固件 Self-Clinching Fasteners 鋁制緊固件 Aluminum Fasteners 鈦合金緊固件 Titanium Alloy Fasteners 尼龍緊固件 Nylon Fasteners 精制緊固件 Finished Fastener 粗制緊固件 Unfinished Fastener 螺紋緊固件 Threaded Fastener 半精制緊固件 Semi-Finished Fastener 抗剪緊固件 Shear Fastener 抗拉緊固件 Tension Fastener 面板緊固件 Panel Fasteners 二、螺栓 Bolts 六角頭螺栓Hexagon Head Bolts 六角法蘭面螺栓Hexagon Flange Bolts 軌道螺栓（魚尾螺絲）Track Bolts 高強度螺栓 High Strength Bolts 地腳螺栓Eyelet Bolts 馬車螺栓 Carriage Bolts 護攔螺栓 Guardrail Bots 焊接螺栓 Weld Bolts 雙頭螺栓 Double End Bolts 鋼結構連接副 Structural Bolting 內六角螺栓 Hex Socket Bolts 合金鋼螺栓 Alloy Steel Bolts 方頭螺栓 Square Head Bolts/Square Bolts 鉤頭螺栓 Hook Bolts 不銹鋼螺栓 Stainless steel Bolts