车辆工程专业英语核心词汇总汇
汽车英语专业词汇(完全篇)
底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphate仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrusion爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate Len镀锌板galvanized plate搭接lap亮丽的外表smart appearance隐藏式固定concealed fastening水洼pending发动机中置式客车bus with under floor engine组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel return ability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping ratio of suspension功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakaway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tire绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test类型type发动机engine内燃机internal combustion engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center)上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency)怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode)额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pistonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head piston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston)凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound piston ring同心活塞环concentric piston ring偏心活塞环eccentric piston ring自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated piston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod 偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod big end连杆杆身connecting rod shank副连杆slave connecting rod叉形连杆fork-and-blade connecting rod主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibration balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order二级往复贯性力reciprocating inertia force, 2nd order离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece camshaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race camshaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓cam contour凸轮包角cam angle凸轮升程cam-lobe lift凸轮尖cam nose凸轮从动件cam follower齿轮传动机构gear drive正时齿轮timing gear链传动机构chain drive链轮sprocket wheel链轮盘chain sprocket正时链条timing chain带齿皮带toothed timing belt链条张紧轮chain tension gear半速齿轮half speed gear正时齿轮刻印记号timing gear punch mark气门valve进气过程intake process换气过程gas exchange process扫气过程scavenging process给气比delivery ratio分层充气stratified charge充量系数volumetric efficiency涡流比swirl rate进气涡流intake swirl螺旋进气道进气helical duct intake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流intake trubulence进气提前角intake advance angle进气持续角intake duration angle进气迟后角intake lag angle进面值time-area value气门升程valve lift气门正时valve timing扫气口面积scavenging port area菌形气门mashroom valve, poppet valve钠冷却气门sodium filled valve(natrium cooled valve) 双气门dual valve进气门intake valve (suction valve,inlet valve)排气门exhaust valve顶置气门overhead valve侧置气门side valve倾斜气门inclined overhead valve直立气门vertical overhead valve套筒式滑阀sleeve valve气门机构valve gear直接式气门驱动机构direct valve gear间接式气门驱动机构indirect valve gear气门杆valve stem加大气门杆oversize valve stem气门头valve head气门工作面valve face气门边限valve margin气门弹簧座valve-spring retainer气门锁片valve key气门间隙调节螺钉valve lash adjusting screw气门旋转器valve rotator气门室valve cage气门油封valve oil seal气门口valve port气门座valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角valve seat angle气门座宽度valve seat width气门挺杆valve tappet(valve lifter)液力挺杆hydraulic tappet(lifter)无间隙挺杆zero-rush tappet (non-clearance tappet)筒形挺杆barrel type tappet油压挺杆ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位tappet rotation排气门挺杆exhaust valve lifter气门导管valve guide气门杆导管stem guide气门重叠度stem overlap气门开启持续时间valve duration气门正时标记valve timing sign气门弹簧valve spring气门内弹簧inner valve spring气门外弹簧outer valve spring刚性缓冲弹簧stiff buffer spring上紧弹簧energizing spring防振气门弹簧non-surging spring弹簧座圈spring retainer蝶形弹簧belleville spring滚柱roller气门室盖valve chamber cover摇臂rocker arm高升程摇臂high lift rocker arm摇臂轴rocker arm shaft推杆push-rod摇臂支架rocker arm bracket气门摇臂室罩valve rocker chamber cover导向轮guide wheel导杆slide bar导轨slide rail张紧轮tensioning wheel链条张紧调节装置assembly chain tension adjuster张紧带轮tensioning pulley传动带张紧装置belt tensioner同步驱动皮带synchronous belt同步驱动皮轮synchronous belt pulley供油系fuel system控制燃烧系统controlled combustion system反湿气装置antipercolator电子燃油喷射electronic fuel injection蒸气回收装置vapor recovery system燃油蒸气回收系统fuel vapor recovery system液体回收装置liquid withdrawal system恒量净化管constant purge line碳罐净化管canister purge line供油量fuel delivery循环供油量fuel delivery per cycle额定供油量rated fuel delivery怠速供油量idling speed fuel delivery供油规律fuel supply rate curve油量调节装置fuel control unit供油提前角fuel supply advance angle进油计量inlet metering几何供油行程geometric fuel delivery stroke供油率fuel supply rate燃油通道fuel gallery有效行程effective stroke剩余行程remainder stroke变行程计量variable stroke metering等容卸载constant volume unloading变容卸载variable volume unloading收缩容积retraction volume燃油喷油装置fuel injection equipment燃油喷射泵fuel injection pump滚轮式燃油喷射泵roll fuel injection pump凸轮轴式燃油喷射泵camshaft fuel injection pump直列式燃油喷射泵in-line fuel injection pump伺服式燃油喷射泵servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵high flanged-mounted fuel injection pump侧向安装燃油喷射泵side-mounted fuel injection pump端部突缘安装式燃油喷射泵end flange-mounted fuel injection pump V形燃油喷射泵vee fuel injection pump脉动式燃油喷射泵jerk fuel injection pump螺纹安装燃油喷射泵screw-mounted fuel injection pump蓄能式燃油喷射泵accumulator fuel injection pump往复式燃油喷射泵reciprocating fuel injection pump驱动轴式燃油喷射泵driveshaft fuel injection pump单缸式燃油喷射泵single cylinder fuel injection pump圆柱式燃油喷射泵cylindrical fuel injection pump旋转式燃油喷射泵rotary fuel injection pump分配式燃油喷射泵distributor fuel injection pump多缸燃油喷射泵multicylinder fuel injection pump框架安装式燃油喷射泵cradle mounted injection pump喷油始点fuel injection beginning喷油终点fuel injection end喷油持续角fuel injection duration angle喷油延迟injection delay引燃喷射pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目number of cylinders of an injection pump无气喷射solid injection喷射正时injection timing集中喷射group injection喷油器injector整体式喷油器unit injector喷嘴nozzle轴针式喷嘴pintle type nozzle环槽式喷嘴annular slot nozzle孔式喷嘴hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴orifice plate nozzle开式喷嘴open nozzle闭式喷嘴closed nozzle喷油提前器timing advance unit喷射泵壳体injection pump housing针阀needle芯轴central spindle喷嘴壳体nozzle body针阀升程needle lift喷嘴盖形螺母nozzle cap nut喷油器壳体nozzle holder突缘安装喷油器壳体flanged-mounted injection nozzle holder 燃油喷射泵传动装置transmision of an injection pump喷嘴锥体nozzle hole cone柱塞plunger柱塞套barrel柱塞行程plunger stroke喷孔spray orifice海拔控制器altitude control提前器飞锤flyweight喷孔长径比ratio of nozzle hole length nozzle diameter喷嘴液动力特性nozzle hydrokinetic characteristics动态相位dynamic phase喷孔面积nozzle hole area喷嘴流通特性nozzle flow characteristic喷油背压injection back pressure高压油管high pressure pipe平均喷油扭矩mean injection torque喷油总效率overall pumping efficiency峰值喷油压力injection peak pressure预行程prestroke收缩行程retraction stroke燃油箱fuel tank油箱盖fuel tank油位表fuel level gauge注油控制装置fill control system汽油箱gasoline tank( petrol tank)汽油供给管gasoline feed pipe加油管filler tube放油螺塞drain plug吸油管suction pipe刚性燃油管rigid fuel pipe进油孔fuel feed hole供油管supply pipe通气管bleeding pipe通气管bleeding pipe泄油阀spill valve泄油孔口spill port进油阀inlet valve最大油量限制器maximum fuel stop滴油dribble燃油表fuel gauge输油泵feed pump燃油泵fuel pump附装燃油箱中的电动燃油泵tank-mounted eletric fuel pump 机械式燃油泵mechanical fuel pump膜片式燃油泵diaphragm fuel supply pump叶片式供油泵vane fuel supply pump活塞式输油泵piston type fuel supply pump齿轮式输油泵gear fuel supply pump电动燃油泵eletric fuel pump带真空泵的汽油泵vacuum pump with fuel pump起动加油器primer起动给油杆primer lever燃油泵上体fuel pump body燃油泵下体fuel pump base燃油泵盖bowl cover进油口接头fuel inlet neck出油口接头fuel discharge port输出阀delivery valve泵油元件pump element回油阀部件fuel return valve assembly化油器carburetor化油器系统carburetor circuit简单化油器elementary carburetor单腔化油器single-barrel carburetor双腔并动化油器two-barrel dual carburetor双腔分动化油器two-barrel duplex carburetor四腔化油器four-barrel carburetor上吸式化油器updaught carburetor下吸式化油器downdraught carburetor平吸式化油器horizontal carburetor侧吸式化油器side-draft-carburetor高海拔补偿式化油器altitude compensating carburetor 化油器附加器adaptor carburetor双腔式化油器twin-choke carburetor固定喉管式化油器fixed venturi carburetor可变喉管化油器variable venturi carburetor化油器接头carburetor adaptor阻风门choke valve阻风活塞choke piston阻风板choke plate自动阻风门automatic choke阻风门拉钮choke button电控自动阻风门electric-assisted choke阻风管choke tube喉管venturi双重或三重喉管double & triple venturi阻风门拉线choke cable化油器小喉管booster venturi浮子系float system浮子float环形浮子annular float同心式浮子concentric float浮子支销float hinge pin浮子针阀float needle valve阀针valve needle浮子油面float level浮子臂float arm侧置浮子室式side float type怠速阀idle valve怠速针阀idle needle省油器economizer省油器阀economizer valve辅助空气阀auxiliary air-valve加速油井accelerating well加速泵accelerating pump加速泵喷嘴accelerating pump nozzle油门throttle手油门hand throttle节气门操纵手柄throttle control lever真空加浓器vacuum booster加浓器excess fuel device量孔体jet block怠速量孔idle metering jet主量孔main metering jet剂量阀活塞dosage valve piston空气量孔air jet燃油滤清器fuel filter沉淀杯sediment bowl串联过滤器in-line filter燃油箱内装过滤器in-tank filter调速器governor飞球式调速器flyball governor调速器governor飞球式调速器flyball governor液压调速器hydraulic governor真空转速调速器vacuum speed governor惯性调速器inertia governor离心调速器centrifugal governor调速器重锤governor weight空气滤清器及进排气系统air cleaner and intake and exhaust sytem 空气滤清器air filter冲压式空气滤清器ram air clearner恒温控制式空气滤清器thermostatic controlled air cleaner油浴式空气滤清器oil bath air cleaner纸质空气滤清器paper air clearner旋流管式空气滤清器swirl tube air filter滤清器滤芯filter element空气滤清器壳体air filter housing空气滤清器盖air filter cover滤清器密封圈filter seal ring滤网sieve滤纸盘或膜filter paper disc or membrane进气和排气系统intake and exhaust system排气管exhaust pipe排气抽气管exhaust extraction duct扫气泵scavenging pump进气预热装置intake preheater进气歧管intake manifold进气歧管真空度intake manifold vacuum冷式进气歧管cold manifold冲压式进气歧管ram intake manifold排气歧管exhaust manifold脉冲式排气歧管pulse exhaust manifold等压排气歧管constant pressrue exhaust manifold排气歧管热量控制阀exhaust manifold heat control valve超高度歧管high-rise manifold升温横跨管道heat crossover排气横跨管道exhaust crossover预热点hot spot阻风门加热器choke heater热空气导流管hot air duct隔热板heat shield排气再循环阀exhaust -gas-recirculation消声器silencer进气消声器intake silencer排气消声器exhaust silencer金属垫片式消声器steel pack muffler玻璃丝消声器glass pack muffler空洞消声器gutted muffler前排气管front exhaust pipe尾管tail pipe消声器联接管intermediate pipe热空气管hot air pipe曲轴箱通风管crankcase bleed pipe隔声罩acoustic hood进气消声器元件silencer element真空泵vacuum pump指示功率indicated power指示热效率indicated thermal efficiency指示油耗率indicated specific energy consumption示功图indicator diagram冷却系cooling system风冷air cooling水冷water-cooling循环流冷却系cooling recovery system自然循环液冷却系统natural circulation type cooling system热流循环液冷却系统thermo-siphon circulation type cooling system 温差循环液冷却系统gravity circulation water cooling system压力式水冷却系统positive circulation cooling system加压式冷却法pressure type cooling水泵循环冷却系统pump circulation cooling system强制循环式化冷系统forced-feed water circulation system 封闭式液冷系统sealed cooling system散热器radiator片式散热器finned radiator管式散热器tubular radiator蜂窝式散热器cellular radiator哈里逊式散热器Harrison type radiator带板式散热器ribbon type radiator上水箱upper tank下水箱lower tank涨溢箱expansion tank散热器芯radiator core之字形管散热器芯film core管-片式散热器芯fin and tube core散热器加水口盖radiator filter cap压力式水箱盖radiator-pressure cap蒸气-空气泄放阀vapor-air release valve散热器护罩radiator cowl散热器百叶窗radiator shutter散热器保温帘radiator roller blind散热片cooling fin缸盖散热片cylinder head fin缸体散热片cylinder block fin控温装置temperature regulating device恒温器thermostat恒温器主阀thermostat main valve恒温器旁通阀thermostat by-pass valve恒温器挠性波纹筒thermostat flexible bellows液体冷却设备liquid cooling equipment水泵water pump水泵体pump casing水泵叶轮water pump impeller旁通进水口water by-pass inlet neck循环泵circulating pump主进水口water main inlet port出水口water outlet port自调式水封self-adjusting seal unit溢流管overflow pipe导流板deflector风扇fan(blower)轴流式风扇axial flow fan离心式风扇centrifugal fan风扇壳体blower casing风扇导流罩fan cowl风扇毂fan hub风扇叶片fan blade风扇叶轮blower impeller风扇导流定子blower stator风扇皮带轮fan pulley三角皮带v-belt风扇护罩fan shroud风扇叶轮叶片impeller vane冷却用空气cooling air风扇导流叶片stator vane强制风冷forced-air cooling自然风冷natural air cooling风道air ducting润滑系lubrication system润滑lubrication气缸上部润滑upper cylinder lubrication 压力润滑pressure-feed lubrication压力润滑法forced lubrication自动润滑automatic lubrication飞溅润滑splash lubrication润滑周期lubrication interval边界润滑borderline lubrication曲轴箱机油油盘crankcase oil pan油底壳oil pan机油盘放油塞sump plug集油器oil collector机油泵oil pump计量式机油泵metering oil pump齿轮式机油泵gear type oil pump转子式机油泵rotor-type oil pump机油泵出油管oil pump outlet pipe放油口oil drain hole油道oil duct断油开关cut-off cock机油散热器oil cooler机油滤清器oil filter机油粗滤器primary oil filter机油精滤器secondary oil filter全流式机油滤清器full-flow oil filter分流式机油滤清器by-pass oil filter离心式机油滤清器centrifugal oil filter 整体式滤芯integral filtering element细滤器滤芯filter element滤清器壳filter box滤片filtering disc机油减压器oil pressure relief valve旁通阀by-pass oil filter机油滤网oil strainer加机油孔oil filter cap滤芯轴filter shaft刮片组件cleaning edge机油量尺dipstick机油滤网oil strainer增压器supercharger增压和扫气装置pressure-charging and scavenging unit 增压装置supercharging device涡轮增压器turbo-charger气波增压器comprex pressure wave supercharger增压器阻风阀supercharger blast gate增压器调节容气量的旁通阀supercharger control bypass 增压器叶轮supercharger impeller惯性增压inertia supercharging机械增压mechanical supercharging涡轮增压turbo-charging增压比supercharge ratio增压压力boost pressure增压中冷inter-cooling中冷度inter-cooling level增压度supercharging level喘振surge喘振线surge line轴流式涡轮axial-flow turbine脉冲进气ram charging发动机试验engine test发动机试验规程engine test procedure发动机技术要求engine technical requirements标准大气状况standard atmospheric conditions大气压力atmospheric pressure进气温度inlet air temperature进气温度inlet air temperature功率校正power correction功率标定power rating功率换算power conversion校正系数correction factor换算系数performance test性能试验performance test起动性能试验starting ability test怠速试验idle running test道路负荷试验road load test各缸工作均匀性试验cylinder variation test背压试验back pressure test最低稳定工作转速试验lowest continuous speed test with load 背部泄漏试验back-leakage test调整试验adjustment test热平衡试验heat balance test快速磨损试验accelerated wear test热冲击试验thermo-shock test空载特性试验no-load characteristic test模拟增压试验simulated supercharging test停缸试验cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验exhaust analysis test突变负荷试验sudden load change test稳定性试验stability test单缸熄火试验one cylinder shut off test例行检查试验routine inspection test验证试验verification test鉴定试验approval test可靠性试验reliability test耐久性试验durability test定型试验type approval test验收试验acceptance test现场试验field test出厂试验delivery test抽查试验spot check test复查试验re-check test台架试验bench test强化试验hop-up test发动机试验台engine test bed底盘测功机chassis dynamometer测功机dynamometer水力测功机hydraulic dynamometer电涡流测功机eddy current dynamometer电力测功机electric dynamometer扭矩仪torque meter转速表tachometer温度测量thermometry温度测量仪器thermometric instruments空气流量测量air flow measurement热线风速仪hot wire anemometer电子示功仪electronic indicator燃烧分析仪combustion analyzer压力传感器pressure transducer精密声级计precision sound level meter排放emission排放物emission排气污染物gaseous pollutant蒸发排放物evaporative emission曲轴箱排放物crankcase emission漏气blowby gas氨氧化物oxids of nitrogen一气化碳carbon monoxide碳氢化合物hydrocarbon甲烷methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons 微粒物particulated matter黑烟black smoke蓝烟blue smoke白烟white smoke碳烟soot光化学烟雾smog臭味odor丙烷propane排放浓度concentration of emission排气烟度exhaust smoke先期排气initial exhaust亚临界排气subcritical exhaust超临界排气supercritical exhaust强制排气forced exhaust自由排气free exhaust排气提前角exhaust advance angle排气迟后角exhaust lag angle排气热损失exhaust heat loss排气净化exhaust purification排气背压exhaust back pressure残余废气residual gas排气有害成分poisonous exhaust composition柴油机排烟diesel smoke综合排放浓度composite concentration of exhaust emission综合排放质量composite mass of exhaust emission排放系数emission factor排放率emission index质量排放量mass emission比排放量brake specific emission排放物控制系统emission control system排气排放物控制系统exhaust emission control system二次空气secondary air二次空气分配歧管secondary air distribution二次空气控制阀secondary air control valve二次空气转换阀secondary air switching valve。
汽车工程专业英语之常用专业词汇表
GLOSSARYAbrasion 磨损Abrasive cleaning磨洗，研磨去污Acceleration加速度Accumulator存储器，储能器Acid 酸Acidity 酸度，酸性Active restraint（指安全带等需要乘客动手使用的）主动保护装置Actuator 执行器A/D converter模/数转换器Adaptive learning 自适应学习Additive 添加剂Adhesion 附着力，附着性Adhesive 附着的，附着力Aeration （空气以微小的气泡状态混入液力系统工作液中的）混气现象Aerodynamics 空气动力学Air bag system 安全气囊系统Air-conditioning 空调Air-conditioning clutch空调（系统的压缩机）离合器Air-conditioning compressor 空调压缩机Air ducts 空气通道Air filter 空气滤清器Air gap 气隙，（火花塞）跳火间隙，间隙Air injection 空气喷射Air Injection Reactor (AIR) 空气喷射反应净化系统All-wheel drive (AWD) 全轮驱动Alternating current 交流电流，交流电Alternator 交流发电机Ambient temperature 环境温度，车外温度American wire gauge (AWG) 美国线规Ammeter 安培计，电流表Ampere 安培Ampere-hour (AH) rating（蓄电池）安培小时容量Amplifier （电压或电流的）放大器Amplify 放大Amplitude 振幅，幅度Anaerobic 厌氧的，厌气的Analog 模拟，类似物Anodize 阳极电镀Antifreeze 防冻剂Antiknock Index (AKI) （车用汽油的）抗爆指数Antilock brake system (ABS) 防抱死制动系统Antiseize compounds 防咬合剂Antisway bar 稳定杆Aqueous 水的，含水的，多水的Aramid fibers芳族聚酸胺纤维，芳香尼龙纤维Aspect ratio （汽车轮胎的）高宽比Asymmetric 不均匀的，不平衡的Asynchronous motor 异步电动机，异步马达Automatic transmission fluid (A TF) 自动变速器液Atkinson cycle 阿特金斯循环Air-fuel ratio (A/F) sensor 空燃比传感器Alignment 调整使…在一条直线上Alloy 合金Automotive aftermarket 汽车配件市场Average responding平均值响应Axial 轴的，轴向的Axial load 轴向载荷Axial play 轴向运动Back pressure （汽车排气系统的）背压Backlash （由于松动等原因造成齿轮等机械系统的）间隙，背隙Ball bearing 球轴承Ball joint球节，球形连接Barometric pressure 大气压力Battery 蓄电池Battery cable （连接启动机或者搭铁的）蓄电池电缆Battery cell 蓄电池单元，单格电池Baud rate 波特率Bottom dead center (BDC) 下止点Bead 轮胎胎圈（轮胎安装在轮辋上的部分）Bearing 轴承Bearing clearance 轴承间隙Bearing crush 轴承压紧量Bearing race 滚动轴承座（圈）Bearing spread 轴承过盈量Bell housing 钟形壳（如离合器壳）Belleville spring 膜片弹簧，蝶形弹簧Belt alternator starter (BAS) 带式发电启动机Bias 偏差Binary code 二进制代码Biodiesel fuels 生物柴油燃料Bit （二进制）位，比特Blowby 窜气Body-over-frame 车身-车架式结构Atmospheric pressure 大气压力Atom 原子Atomization 雾化Bore 缸径Brake band 制动带Brake drum 制动鼓Brake fade 制动器（效能）衰退Brake fluid 制动液Brake pads 制动块，制动摩擦衬块Brake rotor 制动盘Brake shoe 制动蹄British thermal unit (BTU) 英国热量单位Before top dead center (BTDC) 上止点前Bump steer 颠簸转向Burnish 抛光，磨光Byte 字节CAFE standards美国汽车制造厂平均油耗标准Caliper 制动钳Camber车轮外倾，车轮外倾角Camshaft 凸轮轴Controller Area Network (CAN) Bus 控制器局域网总线Candlepower 烛光Capacitor 电容器Carbon dioxide (CO2) 二氧化碳Carbon monoxide (CO) 一氧化碳Carburizing 渗碳剂Case harden 表面硬化Caster主销后倾（角）Catalyst 催化剂Catalytic converter 三元催化转化器Caustic 腐蚀性Center link 中心拉杆Center of gravity 重心Bolt diameter 螺栓直径Bolt head 螺帽Boot 橡胶防尘罩Chlorofluorocarbon (CFC) 氟氯化碳Chamfer 斜面Chamfering 倒角，切角Charcoal canister 活性炭灌Chassis ground 底盘搭铁Check valve 单向阀，止回阀Chemical cleaning 化学清洗Clamping diode钳位（压）二极管Closed loop 闭环Clutch 离合器Clutch disc 离合器盘Clutch fork 离合器拨叉Clutch release bearing 离合器分离轴承Coefficient of friction 摩擦系数Coil pack 线圈组件Cold cranking 低温启动，冷启动Collector 集电极Combination valve 组合阀Combustion 燃烧Combustion chamber 燃烧室Compound 混合物，化合物Compression 压缩Compression ratio 压缩比Compression stroke 压缩冲程Concentric 同中心的Condensation 冷凝，浓缩Condense使冷凝Condenser 冷凝器Conduction 传导Conductor 导体，导线Connecting rod 连杆Centrifugal force 离心力Centripetal force 向心力Cetane 十六烷Control arms控制臂Convection 对流，对流传热Coolant 冷却液Cords（轮胎的）帘线Core 散热器芯Core plug（缸体水套上的）防裂塞片Counterweight 平衡重Crank pin 曲轴连杆轴颈Crank throw 曲柄半径Crankshaft 曲轴Crimp 折叠，卷边Crude oil 原油，石油Curb weight 整车质量Current 电流CV joint 等速万向节Cylinder 汽缸Cylinder head 汽缸盖Dampen 减震，阻尼Dead axle 非传动轴，非驱动桥Deceleration 减速（度）Deck 汽缸体的上表面Deflection 偏转Deflection angle （液力变矩器油液的）偏转角Density 密度Department of Transportation（DOT）美国运输部Desiccant 干燥剂Detergent 清洗剂Detonation 爆燃，爆震Diagnosis 诊断Dial caliper 游标卡尺Dial indicator 千分表Continuously variable transmission (CVT) 无极变速器Contraction收缩Differential 差速器Diffusion 扩散Digital 数字的，数字式的Dilution 稀释Diode 二极管Direct current (DC) 直流，直流电Direct drive 直接驱动，直接传动Direct ignition system (DIS) 直接点火系Direct injection 直接喷射，直喷Directional stability 方向稳定性Disc brakes 盘式制动器Discharge line（空调压缩机的）输出管Displacement （发动机的）排量Distributor 分电器Distributor ignition (DI) system 分电器式点火系统Dome 圆顶（如活塞顶的形状）Dowel 定位销Drive member （行星齿轮机构的）输入齿轮Driveability 操作性能，驾驶性能Drive shaft 传动轴Dry sump 干式油底壳Dual overhead camshaft (DOHC) 双凸轮轴顶置Duo-servo 双向伺服Duty cycle 占空比Dwell time （凸轮轮廓的）同心部分（即随动件相应静止的时间）Dynamic 动力（学）的Dynamic pressure 动压力（当液力流动时的压力）Dynamometer 测功机Eccentric 偏心的Efficiency 效率Diaphragm 膜片Dielectric 绝缘体Diesel fuel 柴油机燃料，柴油Electrochemical degradation (ECD) 电化学降解Electrode 电极Electrolysis 电解Electrolyte 电解液Electromagnet 电磁铁Electromagnetic induction 电磁感应Electromagnetism 电磁学Electromechanical 电动机械的Electromotive force (EMF) 电动势Electronic 电子的Electronic fuel injection (EFI) 电控燃油喷射Element 元素Embedability 压入能力，嵌入性Emitter （晶体管）发射极End play 轴向间隙Energy 能量Engine block 发动机汽缸体，机体Engine efficiency 发动机效率Equilibrium 平衡Ethanol 乙醇，酒精Evacuate 抽成真空Evaporate 蒸发，挥发Evaporation蒸发，挥发Evaporator 蒸发器Exhaust gas recirculation (EGR) 废气再循环Exhaust manifold 排气歧管Exhaust valve 排气门Expansion 膨胀Expansion tank 膨胀箱Expansion valve （空调系统的）膨胀阀Fail-safe circuit 故障安全电路EI 电子点火Elasticity 弹性，弹性变形Electrochemical 电化学的Ferrous metal 含铁金属Field coil 励磁线圈Final drive 主减速器Firing order 点火顺序Flange 法兰Flexible fuel vehicles (FFV) 多用燃料汽车Fluid 流体，流动性Flux density 通量密度Flux field 磁场Flywheel 飞轮Foot-pound 英尺-磅（=·m）Force 力Forge 铸造Forward bias 正向偏压Free play（转向盘的）自由间隙，自由行程Free travel（离合器踏板的）自由行程Frequency 频率Friction 摩擦，摩擦力Fuel cell stack 燃料电池组Fuel pressure regulator 燃油压力调节器Fuel pump 燃油泵Fuel rail 油轨Fulcrum 杠杆的支点Full-floating 全浮式Fuse 熔断器Fusible link 熔断丝Galling wear 表面磨损Gasket 垫圈Gateway 网关Gear 齿轮，挡位，装置，齿轮传动机构Gear pitch 锥齿轮Fan clutch 风扇离合器Fatigue 疲劳Feedback 反馈Glitches短时脉冲波形干扰Grade markings 等级标记Graphite 石墨Grease 润滑脂Greenhouse gas 温室气体Ground 搭铁，接地Gum 胶状沉积物Haldex clutch哈尔德克斯离合器Half shaft 半轴Hall effect 霍尔效应Hand tap 手用丝锥Hardening淬火Hard spots 硬点Hazardous waste 有害废物Head gasket 汽缸垫Heat 热，热量Heat range （火花塞的）热值Heat shield 隔热板Heat sink 散热装置Heat treating 热处理Heater control valve 加热器控制阀Heater core加热器芯Helical gear斜齿圆柱齿轮，斜齿轮Heptane庚烷Hertz (Hz) 赫兹High-intensity discharge (HID) headlamps 高亮度气体放电大灯High tension 高（电）压Hone珩磨Horsepower 马力Hot spot 预热面，预热区（发动机进气歧管与排气Gear ratio 传动比，齿数比Generator 发电机Glaze 光滑面，光滑层Hydrocarbons 碳氢化合物Hydrofluorocarbon (HFC) 氢氟碳化合物，氢氟烃Hypoid gears 准双曲面齿轮Idler pulley 惰轮Ignitability 可燃性Ignition coil 点火线圈Ignition system 点火系统Ignition timing 点火正时Impedance 阻抗Impeller 泵轮Impermeable 不渗透的Included angle 车轮与主销的夹角（主销内倾角与车轮外倾角之和）Induction （电磁）感应Inductive reluctance磁阻Inertia 惯性，惯量Inertia switch 惯性开关Insert bearing 滑动轴承Installed spring height弹簧装配后的高度，装配高度Insulated gate bipolar transistor (IGBT) 绝缘栅双极晶体管Insulator 绝缘体Intake valve 进气阀Integral 整体，总体Integrated circuit 集成电路Integrated motor assist (IMA) system 集成式电动机助推系统Intercooler 中冷器Inverter 变换器（将交流电转变为直流电或将直流电转变为交流电）Isooctane 异辛烷歧管之间的相互接触区，以便利用废气热量促进进气歧管内的燃油进一步气化。
（完整版）车辆工程专业英语核心词汇总汇
Unit 1 Automobile Basicsspare wheel 备胎lubricate 润滑（名词是lubrication ）gearbox 变速箱frame 车架transmission 变速器hood 发动机罩（=bonnet ）→ decklid = trunklid 行李箱盖chassis chassis ['ʃæsi]['ʃæsi]底盘crankshaft 曲轴carburetor carburetor [,kɑːbjʊ'retə][,kɑːbjʊ'retə]化油器spark plug 火花塞clutch 离合器driveshaft 传动轴drive train 传动链petroleum petroleum [pə'trolɪəm][pə'trolɪəm]石油propane 丙烷gasohol 酒精混合燃料Unit 2 Bodies bracket 支架labyrinth labyrinth ['læbərɪnθ]['læbərɪnθ]迷宫cross-member 横梁interposition 干涉steering wheel 方向盘three-box car 三厢车hinge 铰链bumper 保险杠windshield 挡风玻璃windshield wiper 雨刮器interior trim 内饰instrument panel = dashboard 仪表盘safety belt 安全带unibody 承载式车身rubber bush 橡胶衬套vibration 振动ancillary 辅助的stress 应力fender 翼子板curb weight 整备质量intake duct 进气道fatigue 疲劳demist 除雾loudspeaker 扬声器Unit 3 Engines sprocket 链齿轮cylinder 汽缸connecting rod 连杆valve 气门camshaft 凸轮轴lifter 挺杆rocker arm 摇臂valve train 配气机构Unit 4 Fuel System clamp 夹具fuel rail 油轨intake manifold 进气歧管exhaust manifold 排气歧管throttle 节气门squirt 喷射hothouse 温室Unit 5 Electric System circuit 电路coil 线圈ignition 点火alternator 发电机ammeter 安培计voltage regulator 稳压器insulation 绝缘distributor 分电器transistor 晶体管fuse 保险relay 继电器headlights 大灯dome light 顶灯fog lamp 雾灯dash 仪表板halogen 卤素filament 灯丝LED（Light Emitting Diodes）发光二极管Unit 6 Cooling and Lubricating Systems wear 磨损contamination 污染coolant 冷却液radiator 散热器thermostat 节温器grill 格栅，进风口centrifugal force 离心力centripetal force 向心力boiling point 沸点overflow tube 溢流管wax 蜡oil filter 机油滤清器oil pan 油底壳oil galleries 油孔sealing 密封nozzle 喷嘴meshing gear 啮合齿轮bearing 轴承horsepower 马力Unit 7 Exhaust and Emission Control System header pipe 集气管three-way catalytic converter 三元催化转化器三元催化转化器catalyst 催化剂muffler 消音器hanger 挂钩heat shield 隔热板heavy-duty 耐用的，重负荷的fume 烟hydrocarbon 碳氢化合物evaporate 蒸发（名词后缀是-ion）additive 添加剂coupling 连接器gasket 垫圈odorless 无味的positive crankcase ventilation 曲轴箱强制通风曲轴箱强制通风grove 沟槽oil dipstick 油尺vacuum valve 真空阀charcoal canister 活性炭阀idle speed 怠速EGR（Exhaust Gas Recirculation）废气再循环platinum 铂palladium 钯rhodium 铑ceramic 陶瓷的honeycomb 蜂窝状Unit 8 Suspension System, Steering System and Brake System passenger cars/vehicles 乘用车commercial cars/vehicles 商用车bump 路面凸起alignment 校准steering knuckle 转向节swivel 旋转spring 弹簧（sprite 雪碧）ball joint 球型接头shock absorber = damper 减震器bounce 谈起bushing 衬套non-independent suspension 非独立悬架recirculating call steering systems 循环球式转向器rack-and-pinion steering systems 齿轮齿条式转向器齿轮齿条式转向器lorry 货车（也有卡车的意思）truck 卡车worm gear 涡轮蜗杆机构steering linkage 转向连杆steering column 柱pitman arm 转向摇臂track rod 转向横拉杆idler arm 随动臂sleeve 衬套master cylinder 制动主缸lever 杠杆brake booster 制动助力器engine compartment 发动机舱housing 外壳，壳体malfunction 故障，失灵cable 线缆caliper 卡钳brake pads 摩擦片hub 轮毂squeeze 压缩brake shoe 制动蹄Unit 9 Drive Trains and Axlesdrive axles 驱动桥MT（Manual Transmission）手动变速器AT（Automatic Transmission）自动变速器CVT（Continuously Variable Transmission）无级变速器stationary 静态的release bearing 分离轴承clutch fork 离合器拨叉pressure plate 压盘tension 张力hydraulic circuit 液压回路throw-out bearing = release bearing 分离轴承torque converter 液力变矩器friction 摩擦synchronizer 同步器shift linkage 换挡连杆机构turbine 涡轮stator 导轮planet gears 行星齿轮planet gear carrier 行星架行星架ring gear 齿圈slip yoke 滑动叉differential 差速器axle housing 桥壳unsprung weight 簧下质量sprung weight 簧上质量Unit 10 Safety, Security and Navigation Systems occupant = passenger乘员buckle 安全带插扣impact 碰撞regulatory 法规nylon 尼龙stiffness 刚度abrasion 磨损kinetic 运动学的inertia 惯性trigger 触发器resister 电阻GPS（Global Positioning System）全球定位系统补充：assembly line装配线stabilizer bar横向稳定杆cylinder block 气缸体cast iron/aluminium 铸铁/铝turbocharge 涡轮增压supercharge 机械增压exhaust pipe 排气管displacement排量compression ratio压缩比valve overlap 气门重叠thrust washer 止推垫圈ductile iron 球墨铸铁constant velocity joint 等速万向节等速万向节SUV （Sport Utility Vehicle ）运动型多功能车）运动型多功能车常见品牌：Toyota 丰田Honda 本田Nissan 日产Mazda 马自达Lexus 雷克萨斯Suzuki 铃木Mitsubishi 三菱General Motors 通用Cadillac 凯迪拉克Lincoln 林肯Ford 福特Chrysler 克莱斯勒Corvette 克尔维特Mercedes Mercedes [mə'sidi:z][mə'sidi:z][mə'sidi:z] Benz 梅赛德斯-奔驰Volkswagen 大众Audi 奥迪Rolls Royce 劳斯莱斯Bentley 宾利Ferrari 法拉利Maserati 玛莎拉蒂Aston Martin 阿斯顿马丁Jaguar 捷豹Porsche 保时捷Lamborghini 兰博基尼Koenigsegg 柯尼塞格Bugatti 布加迪Pagani 帕加尼Alfa Romeo 阿尔法罗密欧Volvo 沃尔沃Lotus 莲花a m n d A l t h g sb i e o f rRenault 雷诺Hyundai 现代Peugeot 标志Opel 欧宝Fiat 菲亚特Skoda 斯柯达Citroen 雪铁龙Dodge 道奇。
汽车英语专业词汇(完全篇)
底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphate仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrusion爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate Len镀锌板galvanized plate搭接lap亮丽的外表smart appearance隐藏式固定concealed fastening水洼pending发动机中置式客车bus with under floor engine组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel return ability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping ratio of suspension功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakaway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tire绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test类型type发动机engine内燃机internal combustion engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center)上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency)怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode)额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pistonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head piston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston)凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound piston ring同心活塞环concentric piston ring偏心活塞环eccentric piston ring自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated piston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod 偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod big end连杆杆身connecting rod shank副连杆slave connecting rod叉形连杆fork-and-blade connecting rod主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibration balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order二级往复贯性力reciprocating inertia force, 2nd order离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece camshaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race camshaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓cam contour凸轮包角cam angle凸轮升程cam-lobe lift凸轮尖cam nose凸轮从动件cam follower齿轮传动机构gear drive正时齿轮timing gear链传动机构chain drive链轮sprocket wheel链轮盘chain sprocket正时链条timing chain带齿皮带toothed timing belt链条张紧轮chain tension gear半速齿轮half speed gear正时齿轮刻印记号timing gear punch mark气门valve进气过程intake process换气过程gas exchange process扫气过程scavenging process给气比delivery ratio分层充气stratified charge充量系数volumetric efficiency涡流比swirl rate进气涡流intake swirl螺旋进气道进气helical duct intake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流intake trubulence进气提前角intake advance angle进气持续角intake duration angle进气迟后角intake lag angle进面值time-area value气门升程valve lift气门正时valve timing扫气口面积scavenging port area菌形气门mashroom valve, poppet valve钠冷却气门sodium filled valve(natrium cooled valve) 双气门dual valve进气门intake valve (suction valve,inlet valve)排气门exhaust valve顶置气门overhead valve侧置气门side valve倾斜气门inclined overhead valve直立气门vertical overhead valve套筒式滑阀sleeve valve气门机构valve gear直接式气门驱动机构direct valve gear间接式气门驱动机构indirect valve gear气门杆valve stem加大气门杆oversize valve stem气门头valve head气门工作面valve face气门边限valve margin气门弹簧座valve-spring retainer气门锁片valve key气门间隙调节螺钉valve lash adjusting screw气门旋转器valve rotator气门室valve cage气门油封valve oil seal气门口valve port气门座valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角valve seat angle气门座宽度valve seat width气门挺杆valve tappet(valve lifter)液力挺杆hydraulic tappet(lifter)无间隙挺杆zero-rush tappet (non-clearance tappet)筒形挺杆barrel type tappet油压挺杆ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位tappet rotation排气门挺杆exhaust valve lifter气门导管valve guide气门杆导管stem guide气门重叠度stem overlap气门开启持续时间valve duration气门正时标记valve timing sign气门弹簧valve spring气门内弹簧inner valve spring气门外弹簧outer valve spring刚性缓冲弹簧stiff buffer spring上紧弹簧energizing spring防振气门弹簧non-surging spring弹簧座圈spring retainer蝶形弹簧belleville spring滚柱roller气门室盖valve chamber cover摇臂rocker arm高升程摇臂high lift rocker arm摇臂轴rocker arm shaft推杆push-rod摇臂支架rocker arm bracket气门摇臂室罩valve rocker chamber cover导向轮guide wheel导杆slide bar导轨slide rail张紧轮tensioning wheel链条张紧调节装置assembly chain tension adjuster张紧带轮tensioning pulley传动带张紧装置belt tensioner同步驱动皮带synchronous belt同步驱动皮轮synchronous belt pulley供油系fuel system控制燃烧系统controlled combustion system反湿气装置antipercolator电子燃油喷射electronic fuel injection蒸气回收装置vapor recovery system燃油蒸气回收系统fuel vapor recovery system液体回收装置liquid withdrawal system恒量净化管constant purge line碳罐净化管canister purge line供油量fuel delivery循环供油量fuel delivery per cycle额定供油量rated fuel delivery怠速供油量idling speed fuel delivery供油规律fuel supply rate curve油量调节装置fuel control unit供油提前角fuel supply advance angle进油计量inlet metering几何供油行程geometric fuel delivery stroke供油率fuel supply rate燃油通道fuel gallery有效行程effective stroke剩余行程remainder stroke变行程计量variable stroke metering等容卸载constant volume unloading变容卸载variable volume unloading收缩容积retraction volume燃油喷油装置fuel injection equipment燃油喷射泵fuel injection pump滚轮式燃油喷射泵roll fuel injection pump凸轮轴式燃油喷射泵camshaft fuel injection pump直列式燃油喷射泵in-line fuel injection pump伺服式燃油喷射泵servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵high flanged-mounted fuel injection pump侧向安装燃油喷射泵side-mounted fuel injection pump端部突缘安装式燃油喷射泵end flange-mounted fuel injection pump V形燃油喷射泵vee fuel injection pump脉动式燃油喷射泵jerk fuel injection pump螺纹安装燃油喷射泵screw-mounted fuel injection pump蓄能式燃油喷射泵accumulator fuel injection pump往复式燃油喷射泵reciprocating fuel injection pump驱动轴式燃油喷射泵driveshaft fuel injection pump单缸式燃油喷射泵single cylinder fuel injection pump圆柱式燃油喷射泵cylindrical fuel injection pump旋转式燃油喷射泵rotary fuel injection pump分配式燃油喷射泵distributor fuel injection pump多缸燃油喷射泵multicylinder fuel injection pump框架安装式燃油喷射泵cradle mounted injection pump喷油始点fuel injection beginning喷油终点fuel injection end喷油持续角fuel injection duration angle喷油延迟injection delay引燃喷射pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目number of cylinders of an injection pump无气喷射solid injection喷射正时injection timing集中喷射group injection喷油器injector整体式喷油器unit injector喷嘴nozzle轴针式喷嘴pintle type nozzle环槽式喷嘴annular slot nozzle孔式喷嘴hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴orifice plate nozzle开式喷嘴open nozzle闭式喷嘴closed nozzle喷油提前器timing advance unit喷射泵壳体injection pump housing针阀needle芯轴central spindle喷嘴壳体nozzle body针阀升程needle lift喷嘴盖形螺母nozzle cap nut喷油器壳体nozzle holder突缘安装喷油器壳体flanged-mounted injection nozzle holder 燃油喷射泵传动装置transmision of an injection pump喷嘴锥体nozzle hole cone柱塞plunger柱塞套barrel柱塞行程plunger stroke喷孔spray orifice海拔控制器altitude control提前器飞锤flyweight喷孔长径比ratio of nozzle hole length nozzle diameter喷嘴液动力特性nozzle hydrokinetic characteristics动态相位dynamic phase喷孔面积nozzle hole area喷嘴流通特性nozzle flow characteristic喷油背压injection back pressure高压油管high pressure pipe平均喷油扭矩mean injection torque喷油总效率overall pumping efficiency峰值喷油压力injection peak pressure预行程prestroke收缩行程retraction stroke燃油箱fuel tank油箱盖fuel tank油位表fuel level gauge注油控制装置fill control system汽油箱gasoline tank( petrol tank)汽油供给管gasoline feed pipe加油管filler tube放油螺塞drain plug吸油管suction pipe刚性燃油管rigid fuel pipe进油孔fuel feed hole供油管supply pipe通气管bleeding pipe通气管bleeding pipe泄油阀spill valve泄油孔口spill port进油阀inlet valve最大油量限制器maximum fuel stop滴油dribble燃油表fuel gauge输油泵feed pump燃油泵fuel pump附装燃油箱中的电动燃油泵tank-mounted eletric fuel pump 机械式燃油泵mechanical fuel pump膜片式燃油泵diaphragm fuel supply pump叶片式供油泵vane fuel supply pump活塞式输油泵piston type fuel supply pump齿轮式输油泵gear fuel supply pump电动燃油泵eletric fuel pump带真空泵的汽油泵vacuum pump with fuel pump起动加油器primer起动给油杆primer lever燃油泵上体fuel pump body燃油泵下体fuel pump base燃油泵盖bowl cover进油口接头fuel inlet neck出油口接头fuel discharge port输出阀delivery valve泵油元件pump element回油阀部件fuel return valve assembly化油器carburetor化油器系统carburetor circuit简单化油器elementary carburetor单腔化油器single-barrel carburetor双腔并动化油器two-barrel dual carburetor双腔分动化油器two-barrel duplex carburetor四腔化油器four-barrel carburetor上吸式化油器updaught carburetor下吸式化油器downdraught carburetor平吸式化油器horizontal carburetor侧吸式化油器side-draft-carburetor高海拔补偿式化油器altitude compensating carburetor 化油器附加器adaptor carburetor双腔式化油器twin-choke carburetor固定喉管式化油器fixed venturi carburetor可变喉管化油器variable venturi carburetor化油器接头carburetor adaptor阻风门choke valve阻风活塞choke piston阻风板choke plate自动阻风门automatic choke阻风门拉钮choke button电控自动阻风门electric-assisted choke阻风管choke tube喉管venturi双重或三重喉管double & triple venturi阻风门拉线choke cable化油器小喉管booster venturi浮子系float system浮子float环形浮子annular float同心式浮子concentric float浮子支销float hinge pin浮子针阀float needle valve阀针valve needle浮子油面float level浮子臂float arm侧置浮子室式side float type怠速阀idle valve怠速针阀idle needle省油器economizer省油器阀economizer valve辅助空气阀auxiliary air-valve加速油井accelerating well加速泵accelerating pump加速泵喷嘴accelerating pump nozzle油门throttle手油门hand throttle节气门操纵手柄throttle control lever真空加浓器vacuum booster加浓器excess fuel device量孔体jet block怠速量孔idle metering jet主量孔main metering jet剂量阀活塞dosage valve piston空气量孔air jet燃油滤清器fuel filter沉淀杯sediment bowl串联过滤器in-line filter燃油箱内装过滤器in-tank filter调速器governor飞球式调速器flyball governor调速器governor飞球式调速器flyball governor液压调速器hydraulic governor真空转速调速器vacuum speed governor惯性调速器inertia governor离心调速器centrifugal governor调速器重锤governor weight空气滤清器及进排气系统air cleaner and intake and exhaust sytem 空气滤清器air filter冲压式空气滤清器ram air clearner恒温控制式空气滤清器thermostatic controlled air cleaner油浴式空气滤清器oil bath air cleaner纸质空气滤清器paper air clearner旋流管式空气滤清器swirl tube air filter滤清器滤芯filter element空气滤清器壳体air filter housing空气滤清器盖air filter cover滤清器密封圈filter seal ring滤网sieve滤纸盘或膜filter paper disc or membrane进气和排气系统intake and exhaust system排气管exhaust pipe排气抽气管exhaust extraction duct扫气泵scavenging pump进气预热装置intake preheater进气歧管intake manifold进气歧管真空度intake manifold vacuum冷式进气歧管cold manifold冲压式进气歧管ram intake manifold排气歧管exhaust manifold脉冲式排气歧管pulse exhaust manifold等压排气歧管constant pressrue exhaust manifold排气歧管热量控制阀exhaust manifold heat control valve超高度歧管high-rise manifold升温横跨管道heat crossover排气横跨管道exhaust crossover预热点hot spot阻风门加热器choke heater热空气导流管hot air duct隔热板heat shield排气再循环阀exhaust -gas-recirculation消声器silencer进气消声器intake silencer排气消声器exhaust silencer金属垫片式消声器steel pack muffler玻璃丝消声器glass pack muffler空洞消声器gutted muffler前排气管front exhaust pipe尾管tail pipe消声器联接管intermediate pipe热空气管hot air pipe曲轴箱通风管crankcase bleed pipe隔声罩acoustic hood进气消声器元件silencer element真空泵vacuum pump指示功率indicated power指示热效率indicated thermal efficiency指示油耗率indicated specific energy consumption示功图indicator diagram冷却系cooling system风冷air cooling水冷water-cooling循环流冷却系cooling recovery system自然循环液冷却系统natural circulation type cooling system热流循环液冷却系统thermo-siphon circulation type cooling system 温差循环液冷却系统gravity circulation water cooling system压力式水冷却系统positive circulation cooling system加压式冷却法pressure type cooling水泵循环冷却系统pump circulation cooling system强制循环式化冷系统forced-feed water circulation system 封闭式液冷系统sealed cooling system散热器radiator片式散热器finned radiator管式散热器tubular radiator蜂窝式散热器cellular radiator哈里逊式散热器Harrison type radiator带板式散热器ribbon type radiator上水箱upper tank下水箱lower tank涨溢箱expansion tank散热器芯radiator core之字形管散热器芯film core管-片式散热器芯fin and tube core散热器加水口盖radiator filter cap压力式水箱盖radiator-pressure cap蒸气-空气泄放阀vapor-air release valve散热器护罩radiator cowl散热器百叶窗radiator shutter散热器保温帘radiator roller blind散热片cooling fin缸盖散热片cylinder head fin缸体散热片cylinder block fin控温装置temperature regulating device恒温器thermostat恒温器主阀thermostat main valve恒温器旁通阀thermostat by-pass valve恒温器挠性波纹筒thermostat flexible bellows液体冷却设备liquid cooling equipment水泵water pump水泵体pump casing水泵叶轮water pump impeller旁通进水口water by-pass inlet neck循环泵circulating pump主进水口water main inlet port出水口water outlet port自调式水封self-adjusting seal unit溢流管overflow pipe导流板deflector风扇fan(blower)轴流式风扇axial flow fan离心式风扇centrifugal fan风扇壳体blower casing风扇导流罩fan cowl风扇毂fan hub风扇叶片fan blade风扇叶轮blower impeller风扇导流定子blower stator风扇皮带轮fan pulley三角皮带v-belt风扇护罩fan shroud风扇叶轮叶片impeller vane冷却用空气cooling air风扇导流叶片stator vane强制风冷forced-air cooling自然风冷natural air cooling风道air ducting润滑系lubrication system润滑lubrication气缸上部润滑upper cylinder lubrication 压力润滑pressure-feed lubrication压力润滑法forced lubrication自动润滑automatic lubrication飞溅润滑splash lubrication润滑周期lubrication interval边界润滑borderline lubrication曲轴箱机油油盘crankcase oil pan油底壳oil pan机油盘放油塞sump plug集油器oil collector机油泵oil pump计量式机油泵metering oil pump齿轮式机油泵gear type oil pump转子式机油泵rotor-type oil pump机油泵出油管oil pump outlet pipe放油口oil drain hole油道oil duct断油开关cut-off cock机油散热器oil cooler机油滤清器oil filter机油粗滤器primary oil filter机油精滤器secondary oil filter全流式机油滤清器full-flow oil filter分流式机油滤清器by-pass oil filter离心式机油滤清器centrifugal oil filter 整体式滤芯integral filtering element细滤器滤芯filter element滤清器壳filter box滤片filtering disc机油减压器oil pressure relief valve旁通阀by-pass oil filter机油滤网oil strainer加机油孔oil filter cap滤芯轴filter shaft刮片组件cleaning edge机油量尺dipstick机油滤网oil strainer增压器supercharger增压和扫气装置pressure-charging and scavenging unit 增压装置supercharging device涡轮增压器turbo-charger气波增压器comprex pressure wave supercharger增压器阻风阀supercharger blast gate增压器调节容气量的旁通阀supercharger control bypass 增压器叶轮supercharger impeller惯性增压inertia supercharging机械增压mechanical supercharging涡轮增压turbo-charging增压比supercharge ratio增压压力boost pressure增压中冷inter-cooling中冷度inter-cooling level增压度supercharging level喘振surge喘振线surge line轴流式涡轮axial-flow turbine脉冲进气ram charging发动机试验engine test发动机试验规程engine test procedure发动机技术要求engine technical requirements标准大气状况standard atmospheric conditions大气压力atmospheric pressure进气温度inlet air temperature进气温度inlet air temperature功率校正power correction功率标定power rating功率换算power conversion校正系数correction factor换算系数performance test性能试验performance test起动性能试验starting ability test怠速试验idle running test道路负荷试验road load test各缸工作均匀性试验cylinder variation test背压试验back pressure test最低稳定工作转速试验lowest continuous speed test with load 背部泄漏试验back-leakage test调整试验adjustment test热平衡试验heat balance test快速磨损试验accelerated wear test热冲击试验thermo-shock test空载特性试验no-load characteristic test模拟增压试验simulated supercharging test停缸试验cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验exhaust analysis test突变负荷试验sudden load change test稳定性试验stability test单缸熄火试验one cylinder shut off test例行检查试验routine inspection test验证试验verification test鉴定试验approval test可靠性试验reliability test耐久性试验durability test定型试验type approval test验收试验acceptance test现场试验field test出厂试验delivery test抽查试验spot check test复查试验re-check test台架试验bench test强化试验hop-up test发动机试验台engine test bed底盘测功机chassis dynamometer测功机dynamometer水力测功机hydraulic dynamometer电涡流测功机eddy current dynamometer电力测功机electric dynamometer扭矩仪torque meter转速表tachometer温度测量thermometry温度测量仪器thermometric instruments空气流量测量air flow measurement热线风速仪hot wire anemometer电子示功仪electronic indicator燃烧分析仪combustion analyzer压力传感器pressure transducer精密声级计precision sound level meter排放emission排放物emission排气污染物gaseous pollutant蒸发排放物evaporative emission曲轴箱排放物crankcase emission漏气blowby gas氨氧化物oxids of nitrogen一气化碳carbon monoxide碳氢化合物hydrocarbon甲烷methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons 微粒物particulated matter黑烟black smoke蓝烟blue smoke白烟white smoke碳烟soot光化学烟雾smog臭味odor丙烷propane排放浓度concentration of emission排气烟度exhaust smoke先期排气initial exhaust亚临界排气subcritical exhaust超临界排气supercritical exhaust强制排气forced exhaust自由排气free exhaust排气提前角exhaust advance angle排气迟后角exhaust lag angle排气热损失exhaust heat loss排气净化exhaust purification排气背压exhaust back pressure残余废气residual gas排气有害成分poisonous exhaust composition柴油机排烟diesel smoke综合排放浓度composite concentration of exhaust emission综合排放质量composite mass of exhaust emission排放系数emission factor排放率emission index质量排放量mass emission比排放量brake specific emission排放物控制系统emission control system排气排放物控制系统exhaust emission control system二次空气secondary air二次空气分配歧管secondary air distribution二次空气控制阀secondary air control valve二次空气转换阀secondary air switching valve。
车辆工程专业英语复习资料
车辆工程专业英语复习资料1.The four-stroke spark-ignition engine cycle consists:induction stroke (intake stoke), compression stroke, power stroke, exhaust stroke.（四冲程点燃式发动机行程包括：进气行程，压缩行程，作工行程，排气行程。
）2.内燃机：internal combustion engine 外燃机：externalcombustion engine3.The lower the gear ratio selected, the higher the torquetransmitted.（选择的齿轮齿数越少，传递的扭矩越大）4.Different gear 差速器drive shaft 传动轴 final drive 主减速器 universal joints 万向节 steering box 转向器5.These parts can be grouped into four major categories:Body ,Engine, Chassis and electrical system.（这些部件可组成四个主要部分：车身、发动机、底盘和电路系统）6.the purpose of the complete suspension system is to isolatethe vehicle body form road shocks and vibrations,which will otherwise be transferred to the passengers and load.（整个悬架系统的目的是分离车身来自路面的冲击和振动，否则会被传递给乘客和货物。
）7.tube tires 有内胎轮胎 drum brakes鼓式制动器 discbrakes盘式制动器8.most modern lighe vehicles have either disc brakes on thefront wheels and drum brakes on the rear or disc brakes on all 4 wheels大多数现代光车是前轮采用盘式制动鼓上的所有4个车轮后面或盘式制动器制动器9.the electrical system supplies electricity for thestarter，ignition，lights and heater电气系统为起动机、点火系统、照明灯具、取暖器提供电能10.the sparks must be supplied at the right time and theysufficient energy over a range of conditions to ignite the charges火花必须在正确的时间提供足够的能量，他们在一系列的条件下点燃的指控11.distributor分电器 spark plug 火花塞12.Energy is used to produce power. The chemical energy infuel is converted to heat by the burning of the fuel at a controlled rate.（能量是用来产生动力的，燃料中的化学能通过控制其比例进行燃烧可转化成热能。
（精选）汽车专业英语词汇
Accommodation 适应性Aerodynamics 空气动力学Air Conditi oner 空调Air Drag 风阻Air Suspensi on 空气悬挂Analysi s 分析Anti Corrosion 防腐Anti Rust 防锈Ashtray 烟灰盒Assembly 装配Assi stant’s seat 副驾驶座Attaching Parts 附件Azimuth 方位（角）（极坐标）Back Angle 靠背角Backrest 靠背Backup Lamp 倒车灯Binocular Obstruction 双眼盲区BIW (Body-In-White) 白车身Blower 风机Body 车身，车体Bolt 螺栓Bonneted Cab 凸头驾驶室Bracket 托架Breakdown 分块Bumper 保险杠Bushing 衬套Case 壳体Caution Plate 警告牌Centroid 重心Cigarette Lighter 点烟器Chassis 底盘Chassis Frame 车架Check Arm 限位器Clip 卡扣Cluster Meter 组合仪表盘Coat Hanger 衣帽架Coat Hook 衣帽钩Collar 套环Combination Switch 组合开关Comfort 舒适性Component 总成Concealed Wipers 隐藏式雨刮器Condenser 冷凝器Contour 轮廓线Controls 控制件Convex Mirror 凸面镜Coolant 冷却液Cooler 制冷器Crash 碰撞Cup Holder 水杯架Curtain 窗帘Curtain Rail 窗帘滑轨Curvilineal 曲线的Dash Board 前围内板Delivery of the Drawing 出图Displacement 位移Door Check 限位器Door Header Rail 车门顶轨Door Lock 车门锁Door Opening 门洞Door Outer Handle 车门外手柄Door Outer Panel 车门外板Door Panel 门护板Door Pocket 门袋Door Regulator 车门玻璃升降器Door Sash 车门窗框Door Striker 锁环Door Trim 车门护板Door V entilator 三角窗Drip Rail 滴水凹槽顶轨Drive Configuration 驱动形式Dummy Plate 平衡板Dynamic 动态的Ellipsoid Surface 椭球面Emblem 商标Engine 发动机Engineering 工程Entrance Handrail 上车门扶手Entry & Exit 进出Ergonomics 人机工程学Eyellipse 眼椭圆Fatigue Anal ysis 疲劳分析FEM (Finite Element Method) 有限元Fender 翼子板Fender Protector 挡泥护板Fender Stay 挡泥撑条Fender Welt 挡泥衬板Field of View 视野Finish Washer 精加工垫圈Fire Fighting Truck 消防车Fixed 固定的Flange Bolt 凸缘螺栓Fleece 绒毛织物Floor Insulator 地板隔热层Fluid Reservoir 贮液罐Fog Lamp 雾灯Fore/aft 前后Forward Control 平头Frame 车架Front Overhang 前悬Front Panel 前挡板，前围外板Front Turn Signal Lamp 前转向灯Fuse & Relay Box 保险丝和继电器箱Garnish 装饰板Gauge 量表Glare-free 防眩目Glass Run Channel 玻璃滑槽Glazing Rubber Plate 镶玻璃用橡胶板Glove Box 杂物盒Gradeability 爬坡度Grille 格栅Grip 扶手Grommet 密封圈Ground Clearance 离地间隙Halogen Headlamp 卤素大灯Handle Cover 手柄罩Head Contour 头廓包络线Head Restraints 头枕Headlamp 前大灯Headliner 顶棚Headlining 顶棚内饰Headrest 头枕Heater 加热器Heater Plumbing 取暖装置管路Height Adjuster 高度调节器High-mount 高位Hinge 铰链Hinge Bracket 铰链托架Holder 支架Hood 发动机罩Hook 挂钩Hose 软管Impact 碰撞In-line 直列Ingress/egress 进出Inside Lock Knob 内锁止按钮Instrument Panel 仪表板Interior Trim 内饰Intermittent Wiper 间歇式刮水器Joint 接头Joint Duct 连接管道Kinematics 运动学Lateral 横向Lever 杆籁绅士Plate 牌照籁绅士Plate Bracket 牌号托架籁绅士Plate Lamp 车牌灯Lift-up Type 翻转式（前围外板）Linear 线性的Load 载荷Lock Cylinder & Key 锁芯和钥匙Longitudinal 长度方向的Loose Panel 可卸盖板Lower Apron 下挡板Lumbar Support 腰托Luxury Interior Level 豪华内饰Mud Guard 挡泥板Mud Shield 挡泥板（侧）Male-to-Female Ration 男女比例Manikin 人体模型Manoeuvrable 操纵灵活的Meeting Minutes 会议纪要Member 横梁Meter & Gauge 仪表盘Meter Cable 仪表电缆Meter Cluster 仪表束Meter Cover 仪表面罩Meter Face 仪表面Meter Hood 仪表罩Milling 铣Mirror Holder 后视镜支架Model 模型Moquette 绒面Mount 悬置Movable Part 运动件Mudguard 挡泥板Muffler 排气消声器Muscular Contour 强壮的外形（造型风格）））Non-linear 非线性的Nozzle 喷嘴Nut 螺母Operation Hardware 开闭、锁紧装置Optimization 优化Ornament 标识Outlet 出风口Overhead Console Box 高架箱Packing 衬垫Parking Brake Lever 驻车制动手柄Percentile 百分位Perimeter 周长、周边Pillar 立柱Pin 销Pivot Point 关节点Plain Washer 平垫圈Plan V iew 俯视图Plate & Label 名牌和标识Plate Nut 板螺母Pneumatic Spring 空气弹簧Pocket 凹槽Pocket Facing 凹槽镶面Power Steering 动力转向Presentation 展示Push Button 按钮Push-on Spring Nut 顶推弹簧螺母Quarter Panel 后顶盖侧板Quarter Window 侧车窗Radiator 散热器Raised Roof 高顶Rear Overhang 后悬Rear View Mirror 后视镜Rear Wall 后围Reclining 倾斜Reflector 反射板Regulation 法规Reinforcement 加强件Rendering 效果图Requirement 要求Resin 树脂Retainer 护圈Rigidity 刚度Rivet 铆钉Roof Console 高架箱Roof Hatch 天窗Roof Panel 车顶板Room Lamp 室内灯Root-Mean-Square 均方根Round Oval Instrumentation 环抱式仪表板Safety 安全性Screw 螺钉Screw Grommet 密封圈螺钉Scuff 压条（门槛处）Seat Bench 长排座Seat Support 座椅支架Seat Track 座椅导轨Self-Supporting 自承载式Service Parts 修理配件Set Screw 定位螺钉Shim 调整垫片Shin-Knee Contour 膝部包络线Shock Absorber 减振器Side V iew 侧视图Sight Line 视线Silencer 消声器Sill 横梁Simulation 模拟Sketch 草效果图Sleeper 卧铺Sleeping Bed 卧铺Sleeping Berth 卧铺Slide Adjuster 前后滑动调节器Snap Ring 开口环Snorkel 进气管Snowplow 除雪车Spacer 隔环Speedometer 车速仪Splash A pron 侧挡泥板Spot Weldi ng 点焊Static 静态的Steering Column 转向柱Steering Column Adjuster 转向柱调整器Steering Gear 转向机构Steering Wheel 方向盘Step Plate 踏脚板Step Protector 脚踏板护板Stiffener 加强肋Stiffness 刚度Stop Lamp 制动灯Stopper 挡块Strain 应变Strength 强度Stress 应力Structure 结构Styling 造型Sun V isor 遮阳板Surfacing 线图Suspensi on 悬架Switch 开关Tachograph & Speedometer 自记式转速记和车速表Tachometer 发动机转速表Tail Lamp 尾灯Tapping Screw 自攻螺钉Template 模板Ticket/Card Holder 名片夹Tilt 翻转（驾驶室）Tipper 自卸车Tonnage 吨位Torsional Stiffness 扭转刚度Tread 轮距Trim 饰件Trim Panel 装饰板Turning Radius 转弯半径Upper Console 高架箱V ariant 变形车V entilation 通风V ertical 垂直方向的Vinyl 乙烯基Washer 垫圈Water Proof Film 防水层Weather Strip 密封条Wear-Resistant 防磨Windscreen 风窗Windshield 风窗Windshield Washer 挡风玻璃洗涤器Windshield Wiper 挡风玻璃刮水器Wiper 刮水器Wiper Arm 刮臂Wiper Blade 刮片Wiper Link Assembly 刮水器连杆组件Wiring Harness 线束b248b24807-09-08 12:22 轮椅升降机Wheel chair lift图例legend工位stati on吊运装置overhead hoist更衣室restroom1号厂房工艺布置方案图proposal of the Plant I layout合笼mate底盘平移台chassi s shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassi s左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutti ng内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoi st小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine hol ding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphating仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrution 爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resi stant聚碳化透镜poly-carbonate len镀锌板galvanized plate搭接lap亮丽的外表smart apperance隐藏式固定concealed fastening水洼ponding发动机中置式客车bus with under floor engi ne组合式客车车身modular bus body薄壳式结构shell constructi on衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel returnability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test 极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping raito of suspension 功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tyre绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pul se response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test汽车发动机类型type发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injecti on engine火花点火式发动机spark ignition engi ne压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engi ne柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engi ne直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engi ne油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine 柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engi ne双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed pi ston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engi ne直列式发动机in-line engi ne星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engi ne顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side val ve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engi ne性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke 换气压缩行程exchange-compression stroke 止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center) 上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept vol ume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression rati o临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effecti ve pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effecti ve thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean pi ston speed发动机转速engine speed (rotational frequency) 怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode) 额定工况declared working condition变工况variable working condition稳定工况steady working conditi on空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-cl ockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics 万有特性mapping characteri stics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体statorb248b24807-09-08 12:23 缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechani sm casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsi diary combustion chamber预燃室prechamber涡流燃烧室`swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combusti on chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume rati o of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area rati o of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechani sm cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pi stonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head pi ston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston) 凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance pi ston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston 滑裙活塞slipper pi ston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander 滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating pi ston pin 半浮式活塞销semifloating pi ston pin 固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound pi ston ring 同心活塞环concentric piston ring 偏心活塞环eccentric piston ring 自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated pi ston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod bi g end连杆杆身connecting rod shank副连杆slave connecti ng rod叉形连杆fork-and-blade connecting rod 主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper 扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibrati on balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order 二级往复贯性力reciprocating inertia force, 2nd order 离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece cam shaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race cam shaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮汽车词汇（2）出处：作者：swm45100 FanE『翻译中国』2004-5-27 14:07:30 中间齿轮intermediate gear(counter gear)副轴齿轮counter shaft gear副轴counter shaft变速器输入轴transmission imput shaft变速器输出轴transmission output shaft变速器主动齿轮轴transmission drive gear shaft变速器主轴transmission main shaft变速器中间轴transmission countershaft变速器轴的刚度rigidity of shaft变速齿轮比（变速比）transmission gear rati o传动比gear ratio主压力line pressure调制压力modulated pressure真空调制压力vacuum modulator pressure速控压力governor pressure缓冲压力compensator or trimmer pressure 限档压力hold presure前油泵front pump (input pump )液力传动装置充油压力hydrodynamic unit change pressure 后油泵gear pump (output pump )回油泵scavenge oil pump调压阀pressure -regulator vavle电磁阀调压阀solenoid regulator valve液力变矩器旁通阀converter bypass val ve速控阀governor valve选档阀selectro val ve换档阀shift valve信号阀signal valve继动阀relay valve换档指令发生器shift pattern generator档位指示器shift indicator(shift torwer)先导阀priority valve流量阀flow valve重迭阀overlap valve液力减速器控制阀retarder control val ve液力起步fluid start零速起动stall start液力变矩器锁止converter lockup全液压自动换档系统hydraulic automatic control system 电液式自动换档系统electronic -hydraulic automatiec 换档shift升档upshift降档downshift动力换档power shfit单向离合器换档freewheel shfit人工换档manual shfit自动换档automaitc shfit抑制换档inhibited shift超限换档overrun shift强制换档forced shift换档点shift point叶片转位blade angle shift换档滞后shift hysteresis换档循环shift schedule换档规律process of power shift动力换档过程timing换档定时property of automatic shift换档品质property of automatic shft换档元件engaging element换档机构操纵杆control lever变速杆stick shift(gear shift lever)（副变速器）变速杆range selector变速叉shifting fork (gear shift fork)分动箱控制杆transfer gear shift fork变速踏板gear shift pedal变速轨（拨叉道轨）shift rail直接变速direct change(direct control)方向盘式变速column shift (handle change)按钮控制finger-tip control槽导变速gate changeb248b24807-09-08 12:23 空档位置neutral position直接驱动direct drive高速档top gear(high gear)低速档bottom gear(low speed gear)第一档first gear第二档second gear超速档overdirve gear经济档economic gear倒档reverse gear爬行档驱动特性drive performance反拖特性coast performance定输入扭矩特性constant input torque performance全油门特性full throttle performance寄生损失特性no load (parasitic losses)performance 原始特性primary characteristic响应特性response characteri stic吸收特性absorption characteristic全特性total external characteristic输入特性characteristic of enhance输出特性characteristic of exit力矩特性torque factor(coefficient of moment) 过载系数overloading ratio变矩系数torque ratio能容系数capacity factorr几何相似geometry similarity运动相似kinematic similarity动力相似dynamic similarity透穿性transparency万向节和传动轴universal joint and drive shaft万向节universal joint非等速万向节nonconstant velocity universal joint 等速万向节constant velocity universal joint准等速万向节near constant velocity universal joint 自承式万向节self-supporti ng uni versal joint非自承式万各节non self suporting universal joint回转直径swing diameter等速平面constant velocity plane万向节夹角true joint angle十字轴式万向节cardan (hookes)universal joint万向节叉yoke突缘叉flange york滑动叉slip yoke滑动节，伸缩节slip joint花键轴叉slip shaft yoke轴管叉（焊接叉）tube(weld yoke)十字轴cross(spi der)十字轴总成cross assembly挠性元件总成flexible universal joint球销式万向节flexible member assembly双柱槽壳housing球环ball球头轴ball head球头钉button中心球和座centering ball and seat球笼式万向节rzeppa uni versal joint钟形壳outer race星型套inner race保持架cage可轴向移动的球笼式万向节plunging constant vel ocity joint筒形壳cylinder outer race柱形滚道星形套inner race withcylinder ball grooves 偏心保持架non-concentric cage滚动花键球笼式万向节ball spline rzeppa universal joint外壳outer housing内壳体inner housing球叉式万向节weiss universal joint球叉ball yoke定心钢球centering ball三球销万向节tripod universal joint三柱槽壳housing三销架spider双联万向节double cardan universal joint凸块式万向节tracta universal joint凸块叉fork yoke榫槽凸块tongue and groove couplijng凹槽凸块groove coupling传动轴drive shaft(propeller shaft)传动轴系drive line传动轴形式drive shaft type两万向节滑动的传动轴two -joint inboard slip ddiveshaft 两万向节外侧滑动传动轴two joint ouboard slip drive shaft 单万向节传动轴single joint coupling shaft组合式传动轴unitized drive shaft传动轴减振器drive shaft absorber传动轴中间轴承drive shaft center bearing传动轴管焊接合件weld drive shaft tube assembly 传动轴特征长度drive shaft length传动轴谐振噪声resonant noi se of rive shaft传动轴的临界转速critical speed of drive shaft传动轴总成的平衡balance of drive shaft assembly 允许滑动量slip相位角phase angle传动轴安全圈drive shaft safety strap驱动桥drive axle(driving axle)类型type断开式驱动桥divided axle非独立悬架式驱动桥rigid dirve axle独立悬架式驱动桥independent suspensi on drive axle转向驱动桥steering drive axle贯通式驱动桥tandem axles“三速”贯通轴"three-speed" tandem axles单驱动桥single drive axle多桥驱动multiaxle drive减速器reducer主减速器final drive单级主减速器single reduction final drive双级主减速器double reduction final drive前置式双级主减速器front mounted double reducti on final drive后置式双级主减速器rear mounted double reduction final drive上置式双级主减速器top mounted double reducton final drive行星齿轮式双级主减速器planetary double reducti on final drive贯通式主减速器thru-drive双速主减速器two speed final drive行星齿轮式双速主减速器two speed planetary final drive双级双速主减速器two speed double reducti on final drive轮边减速器wheel reductor(hub reductro)行星圆柱齿轮式轮边减速器planetary wheel reductor行星锥齿轮式轮边减速器differential geared wheel reductor(bevelepicyclick hub reductor) 外啮合圆柱齿轮式轮边减速器spur geared wheel reductor差速器differential锥齿轮式差速器bevel gear differential圆柱齿轮式差速器spur gear differential防滑式差速器limited -slip differential磨擦片式自锁差速器multi-disc self -locking differential凸轮滑滑块自锁差速器self-locking differential with si de ring and radial cam plate 自动离合式自锁差速器automoti ve positive locking differential强制锁止式差速器locking differential液压差速器hydraulic differential轴间差速器interaxial differential差速器壳differential carrieer(case)主降速齿轮final reduction gear驱动轴减速比axle ratio总减速比total reduction ratio主降速齿轮减速比final reduction gear ratio双减速齿轮double reduction gear差速器主齿轮轴differential pinion-shaft差速器侧齿轮differential side gear行星齿轮spider gear(planetary pinion)螺旋锥齿轮spiral bevel gear双曲面齿轮hypoid gear格里林齿制gleason tooth奥林康型齿制oerlikon tooth锥齿轮齿数number of teeth in bevel gears and hypoid gears锥齿轮齿宽face width of tooth in bevel gears and hypoi d gears 平面锥齿轮plane bevel gear奥克托齿形octoid form平顶锥齿轮contrate gear齿面接触区circular tooth contact齿侧间隙backlash in circular tooth差速器十字轴differential spider差速器锁止机构differential locking -device差速器锁止系数differential locking factor差速器壳轴承carrier bearing桥壳axle housing整体式桥壳banjo housing可分式桥壳trumpet-type axle housing组合式桥壳unitized carrier-type axle housing对分式桥壳split housing冲压焊接桥壳press-welding axle housi ng钢管扩张桥壳expanded tube axle housing锻压焊接桥壳forge welding axle housing整体铸造式桥壳cast rigid axle housing半轴。
车辆工程专业英语核心词汇总汇
Unit 1 Automobile Basicsspare wheel 备胎lubricate 润滑（名词是lubrication）gearbox 变速箱frame 车架transmission 变速器hood 发动机罩（=bonnet）→ decklid = trunklid 行李箱盖chassis ['ʃæsi] 底盘crankshaft 曲轴carburetor [,kɑːbjʊ'retə] 化油器spark plug 火花塞clutch 离合器driveshaft 传动轴drive train 传动链petroleum [pə'trolɪəm] 石油propane 丙烷gasohol 酒精混合燃料Unit 2 Bodiesbracket 支架labyrinth ['læbərɪnθ]迷宫cross-member 横梁interposition 干涉steering wheel 方向盘three-box car 三厢车hinge 铰链bumper 保险杠windshield 挡风玻璃windshield wiper 雨刮器interior trim 内饰instrument panel = dashboard 仪表盘safety belt 安全带unibody 承载式车身rubber bush 橡胶衬套vibration 振动ancillary 辅助的stress 应力fender 翼子板curb weight 整备质量intake duct 进气道fatigue 疲劳demist 除雾loudspeaker 扬声器Unit 3 Engines.sprocket 链齿轮cylinder 汽缸connecting rod 连杆valve 气门camshaft 凸轮轴lifter 挺杆rocker arm 摇臂valve train 配气机构Unit 4 Fuel Systemclamp 夹具fuel rail 油轨intake manifold 进气歧管exhaust manifold 排气歧管throttle 节气门squirt 喷射hothouse 温室Unit 5 Electric Systemcircuit 电路coil 线圈ignition 点火alternator 发电机ammeter 安培计voltage regulator 稳压器insulation 绝缘distributor 分电器transistor 晶体管fuse 保险relay 继电器headlights 大灯dome light 顶灯fog lamp 雾灯dash 仪表板halogen 卤素filament 灯丝LED（Light Emitting Diodes）发光二极管Unit 6 Cooling and Lubricating Systems wear 磨损contamination 污染coolant 冷却液radiator 散热器thermostat 节温器grill 格栅，进风口centrifugal force 离心力centripetal force 向心力boiling point 沸点overflow tube 溢流管wax 蜡oil filter 机油滤清器oil pan 油底壳oil galleries 油孔sealing 密封nozzle 喷嘴meshing gear 啮合齿轮bearing 轴承horsepower 马力Unit 7 Exhaust and Emission Control System header pipe 集气管three-way catalytic converter 三元催化转化器catalyst 催化剂muffler 消音器hanger 挂钩heat shield 隔热板heavy-duty 耐用的，重负荷的fume 烟hydrocarbon 碳氢化合物evaporate 蒸发（名词后缀是-ion）additive 添加剂coupling 连接器gasket 垫圈odorless 无味的positive crankcase ventilation 曲轴箱强制通风grove 沟槽oil dipstick 油尺vacuum valve 真空阀charcoal canister 活性炭阀idle speed 怠速EGR（Exhaust Gas Recirculation）废气再循环platinum 铂palladium 钯rhodium 铑ceramic 陶瓷的honeycomb 蜂窝状Unit 8 Suspension System, Steering System and Brake System passenger cars/vehicles 乘用车commercial cars/vehicles 商用车bump 路面凸起alignment 校准steering knuckle 转向节swivel 旋转spring 弹簧（sprite 雪碧）ball joint 球型接头shock absorber = damper 减震器bounce 谈起bushing 衬套non-independent suspension 非独立悬架recirculating call steering systems 循环球式转向器rack-and-pinion steering systems 齿轮齿条式转向器lorry 货车（也有卡车的意思）truck 卡车worm gear 涡轮蜗杆机构steering linkage 转向连杆steering column 柱pitman arm 转向摇臂track rod 转向横拉杆idler arm 随动臂sleeve 衬套master cylinder 制动主缸lever 杠杆brake booster 制动助力器engine compartment 发动机舱housing 外壳，壳体malfunction 故障，失灵cable 线缆caliper 卡钳brake pads 摩擦片hub 轮毂squeeze 压缩brake shoe 制动蹄Unit 9 Drive Trains and Axlesdrive axles 驱动桥MT（Manual Transmission）手动变速器AT（Automatic Transmission）自动变速器CVT（Continuously Variable Transmission）无级变速器stationary 静态的release bearing 分离轴承clutch fork 离合器拨叉pressure plate 压盘tension 张力hydraulic circuit 液压回路throw-out bearing = release bearing 分离轴承torque converter 液力变矩器friction 摩擦synchronizer 同步器shift linkage 换挡连杆机构turbine 涡轮stator 导轮planet gears 行星齿轮planet gear carrier 行星架ring gear 齿圈slip yoke 滑动叉differential 差速器axle housing 桥壳unsprung weight 簧下质量sprung weight 簧上质量Unit 10 Safety, Security and Navigation Systems occupant = passenger乘员buckle 安全带插扣impact 碰撞regulatory 法规nylon 尼龙stiffness 刚度abrasion 磨损kinetic 运动学的inertia 惯性trigger 触发器resister 电阻GPS（Global Positioning System）全球定位系统补充：assembly line装配线stabilizer bar横向稳定杆cylinder block 气缸体cast iron/aluminium 铸铁/铝turbocharge 涡轮增压supercharge 机械增压exhaust pipe 排气管displacement排量compression ratio压缩比valve overlap 气门重叠thrust washer 止推垫圈.ductile iron 球墨铸铁constant velocity joint 等速万向节SUV（Sport Utility Vehicle）运动型多功能车常见品牌：Toyota 丰田Honda 本田Nissan 日产Mazda 马自达Lexus 雷克萨斯Suzuki 铃木Mitsubishi 三菱General Motors 通用Cadillac 凯迪拉克Lincoln 林肯Ford 福特Chrysler 克莱斯勒Corvette 克尔维特Mercedes [mə'sidi:z] Benz梅赛德斯-奔驰Volkswagen 大众Audi 奥迪.Rolls Royce 劳斯莱斯Bentley 宾利Ferrari 法拉利Maserati 玛莎拉蒂Aston Martin 阿斯顿马丁Jaguar 捷豹Porsche 保时捷Lamborghini 兰博基尼Koenigsegg 柯尼塞格Bugatti 布加迪Pagani 帕加尼Alfa Romeo 阿尔法罗密欧Volvo 沃尔沃Lotus 莲花Renault 雷诺Hyundai 现代Peugeot 标志Opel 欧宝Fiat 菲亚特Skoda 斯柯达Citroen 雪铁龙Dodge 道奇.。
车辆工程专业英语词汇
车辆工程专业英语词汇摘要车辆工程是一门涉及机械、电子、控制、材料等多方面知识的综合性学科，主要研究车辆的设计、制造、试验、维修和管理等方面的理论和方法。
车辆工程专业的学生需要掌握一定的专业英语词汇，以便与国际同行进行交流和合作，以及阅读和撰写相关的文献和报告。
本文根据车辆工程专业的主要课程，给出了所涉及的专业英语词汇。
本文旨在为车辆工程专业的学生和教师提供一个参考和学习的资料。
1. 物理 Physics物理是一门研究自然界基本规律和现象的科学，是车辆工程专业的基础课程之一。
物理主要包括力学、热学、电磁学、光学、近代物理等分支。
以下是物理课程中常用的专业英语词汇：中文英文物理physics力学mechanics热学thermodynamics电磁学electromagnetism光学optics近代物理modern physics力force质量mass速度velocity加速度acceleration动量momentum功work能量energy功率power压强pressure温度temperature熵entropy热力学第一定律the first law of thermodynamics热力学第二定律the second law of thermodynamics电荷charge电流current电压voltage电阻resistance电容capacitance电感inductance欧姆定律Ohm's law基尔霍夫定律Kirchhoff's laws磁场magnetic field磁通量magnetic flux中文英文法拉第定律Faraday's law麦克斯韦方程组Maxwell's equations光源light source光线ray of light光强度intensity of light波长wavelength频率frequency折射率refractive index反射定律the law of reflection折射定律the law of refraction2. 高等数学 Advanced Mathematics高等数学是一门研究函数、极限、微积分、线性代数、微分方程等数学内容的科学，是车辆工程专业的基础课程之一。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1
备胎
润滑（名词是）
变速箱
车架
变速器
发动机罩（）→= 行李箱盖['ʃæ] 底盘
曲轴
[ɑːʊ'ə] 化油器
火花塞
离合器
传动轴
传动链
[pə'ɪəm] 石油
丙烷
酒精混合燃料
2
支架
['læbərɪnθ]迷宫
横梁
干涉
方向盘
三厢车
铰链
保险杠
挡风玻璃
雨刮器
内饰
= 仪表盘
安全带
承载式车身
橡胶衬套
振动
辅助的
应力
整备质量进气道疲劳
除雾
扬声器
3
链齿轮
汽缸
连杆
气门
凸轮轴
挺杆
摇臂
配气机构
4
夹具
油轨
进气歧管排气歧管节气门
喷射
温室
5
电路
线圈
点火
发电机
安培计
稳压器绝缘
分电器
晶体管
保险
大灯
顶灯
雾灯
仪表板
卤素
灯丝
（）发光二极管
6
磨损
污染
冷却液
散热器
节温器
格栅，进风口
离心力
向心力
沸点
溢流管
蜡
机油滤清器
油底壳
油孔
密封
喷嘴
啮合齿轮
轴承
马力
7
集气管
三元催化转化器催化剂
消音器
挂钩
隔热板
耐用的，重负荷的
烟
碳氢化合物
蒸发（名词后缀是）
添加剂
连接器
垫圈
无味的
曲轴箱强制通风
沟槽
油尺
真空阀
活性炭阀
怠速
（）废气再循环
铂
钯
铑
陶瓷的
蜂窝状
8 ,
乘用车
商用车
路面凸起
校准
转向节
旋转
弹簧（雪碧）
球型接头
= 减震器
谈起
衬套
非独立悬架
循环球式转向器
齿轮齿条式转向器
货车（也有卡车的意思）
涡轮蜗杆机构
转向连杆
柱
转向摇臂
转向横拉杆
随动臂
衬套
制动主缸
杠杆
制动助力器
发动机舱
外壳，壳体
故障，失灵
线缆
卡钳
摩擦片
轮毂
压缩
制动蹄
9
驱动桥
（）手动变速器（）自动变速器（）无级变速器静态的
分离轴承
离合器拨叉
压盘
张力
液压回路
= 分离轴承
液力变矩器
摩擦
同步器
换挡连杆机构
导轮
行星齿轮
行星架
齿圈
滑动叉
差速器
桥壳
簧下质量
簧上质量
10 ,
= 乘员
安全带插扣
碰撞
法规
尼龙
刚度
磨损
运动学的
惯性
触发器
电阻
（）全球定位系统
补充：
装配线
横向稳定杆
气缸体
铸铁/铝
涡轮增压
机械增压
排气管
排量
压缩比
气门重叠
止推垫圈
球墨铸铁
等速万向节
（）运动型多功能车
常见品牌：
丰田
本田
日产
马自达
雷克萨斯
铃木
三菱
通用
凯迪拉克
林肯
福特
克莱斯勒
克尔维特
[mə'] 梅赛德斯-奔驰大众
奥迪
劳斯莱斯
宾利
法拉利
玛莎拉蒂
阿斯顿马丁
捷豹
保时捷
兰博基尼
柯尼塞格
布加迪
帕加尼
阿尔法罗密欧
沃尔沃
莲花
雷诺现代标志欧宝菲亚特斯柯达雪铁龙道奇。