紧固件专业英语词汇
紧固件-中英文对照
紧固件-中英文对照No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出) A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut 六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt 车辆(汽车)螺丝、螺帽Automotive Fasteners 航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws 链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy 重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws 套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed CapNuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod 线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire 不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives 成型冲模Header Punches In Various Drives 螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass) 螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉SpheroidizingBright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator 滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet MetalFasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains 机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-LowThread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。
最全紧固件中英文对照，外贸必备词典一
最全紧固件中英文对照，外贸必备词典一小编精心整理了一些紧固件行业常见的英文词汇，是紧固件外贸人士必备专业词典，是外贸新手快速入门的阶梯，赶快收藏吧！一、紧固件标准紧固件 Standard Fasteners非标准紧固件 Nonstandard Fasteners特殊紧固件 Special Fasteners汽车紧固件 Automotive Fasteners铜制紧固件 Brass Fasteners航天用紧固件 Aerospace Fasteners精密紧固件 Precision Fasteners化学紧固件 Chemical Fasteners摩托车紧固件 Motorcycle Fasteners不锈钢紧固件 Stainless Steel Fasteners铁道紧固件 Railway Fasteners防松紧固件 Self-locking Fasteners高强度紧固件 High strength FastenersPEM紧固件 PEM Fasteners钢结构紧固件 Steel Structural Fasteners压铆紧固件 Self-Clinching Fasteners铝制紧固件 Aluminum Fasteners钛合金紧固件 Titanium Alloy Fasteners尼龙紧固件 Nylon Fasteners精制紧固件 Finished Fastener粗制紧固件 Unfinished Fastener螺纹紧固件 Threaded Fastener半精制紧固件 Semi-Finished Fastener抗剪紧固件 Shear Fastener抗拉紧固件 Tension Fastener面板紧固件 Panel Fasteners二、铆钉平头铆钉 Flat Head Rivets击芯铆钉 Drive Rivets彩色铆钉 Colored Rivets沉头铆钉 Countersunk Head Rivets半沉头铆钉 Oval Countersunk Head Rivets平锥头铆钉 Cone Head Rivets抽芯铆钉 Blind Rivets开口铆钉 Split Rivets开口型抽芯铆钉 Open End Blind Rivets拉铆钉 Pop Rivets封闭铆钉Closed End Rivets封闭性抽芯铆钉 Closed End Blind Rivet塑料铆钉 Plastic Rivets空心铆钉 Tubular Rivets环槽铆钉 Ring Groove Rivets单鼓型铆钉 Single-Grip Blind Rivet圆头铆钉 Round Head Rivets高沉头铆钉 Countersunk Head Rivets铝铆钉 Aluminum Rivets实心铆钉 Solid Rivets沉头实心铆钉 Countersunk Head Solid Rivets防水型灯笼铆钉 Trl-fold Rivet With Water Resistance 半空心铆钉 Semi-Tubular Rivets圆头半空心铆钉 Semi-tubular Pan Head Rivets异型铆钉 Special Rivets不锈钢铆钉 Stainless Steel Rivets双鼓型铆钉 MultiGrip Blind Rivet内锁拉丝铆钉 H-Lock Blind Rivets外锁拉丝铆钉 Hem-Fix Blind Rivets海马钉 H-Bolt Blind Rivets高强度铆钉 High Strength Rivets台阶铆钉 Step Rivets面板铆钉 Tablet Rivets开花型抽芯铆钉 Flowering Blind Rivets拉花型抽芯铆钉 Peel Type Blind Rivets沟槽型抽芯铆钉 Grooved Type Blind Rivet铆接工具 Riveting T ool恒丰铆钉产品包括开口型抽芯铆钉，封闭型抽芯铆钉，单鼓型抽芯铆钉，多鼓型抽芯铆钉，内锁拉丝铆钉，外锁拉丝铆钉，海马钉，灯笼铆钉等。
紧固件术语名词中英文对照
螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度1 标准GB （国标）ISO(国际标准)DIN（德制）JIS（日标）ANSI /ASME （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓 C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓常用紧固件英语Cup head square neck bolts 半圆头方螺栓Cup head nib bolts 半圆头带榫螺栓Cup head square neck bolts with large head –product grade C大半圆头方颈螺栓 C级Hexagon head bolts-product grade C六角头螺栓 C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹 C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆菌B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员 B级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉。
紧固件标准英语
紧固件类英语词汇/discuz/archiver/tid-81740.html白铁盖螺丝A2(18-8)Cap Screws 水平调整螺丝Adjusted levelingscrews航天扣件Aerospace Fasteners合金钢螺丝(栓) alloy steel screws (bolts)铝螺丝aluminum screws 车辆(汽车)螺丝、螺帽automotive fasteners复含材料钻尾螺丝bi-metal self drilling screws 大尺寸螺丝big size bolts 公母螺丝组BINDER POST & Screw set 拉栓blind bolts 铜螺丝(栓) brass screws (bolts) 建筑螺丝building fasteners 建筑膨涨螺丝building wall anchor 半圆头六角孔螺丝button head socket cap screws 马车螺丝carriage bolts 活动轮螺丝附件castors fittings 塑板螺丝chipboard screws 快速钉紧螺丝及螺帽clinch studs & nuts 挤压扣件clinching fasteners 齿花扣件clinching parts 宽牙螺丝coarse thread screws 链带螺丝collated screws 水泥螺丝concrete screws 板模扣件construction fasteners 货柜螺丝container screws 耐候钢螺丝conten steel heavy hex bolts 鱼尾螺丝conten steel oval neck track bolts 双刀螺丝cutter screws 匣板螺丝deck screws 锌蝶螺丝die cast wing screws;zinc alloy 双头牙螺丝double end screws, hanger bolt 旋锁螺丝drive lock screws 旋入螺丝drive screws 墙用螺丝drywall screws ejot delta pt screws ejot pt screws 电子螺丝electronic screws 电梯螺丝elevator bolts 欧洲螺丝euro screws 环首螺丝eye bolts 冈山头螺丝fillister screws 鳍头螺丝fin neck round head bolts 管配件接头fitting fasteners (connectors) 突缘螺丝flange bolts (screws) 平头六角孔螺丝flat head socket cap screws 平纺螺丝flat pan head screws 地板螺丝flooring panel screws 基础螺丝foundation bolts 框架支撑螺丝frame anchor-lag round screws 家俱螺丝furniture screws (connecting bolts) 重型车螺丝、螺帽heavy duty wheel hub bolts & nuts 六角螺丝(栓) hex head cap screws (hex bolts) 六角机械螺丝hex head machine bolts 六角木牙螺丝hex lag bolts 内六角孔螺丝hex socket cap screws 等高螺丝hex socket head shoulder screw薄头强力螺丝hex socket low head cap screw 内六角固定螺丝hex socket set screws 华司头机械螺丝hex washer head machine screws 高低牙螺丝high low thread screws 高张力螺丝hex socket head shoulder screw 铰链螺丝hinge screws 勾头螺栓hook bolts 管夹螺丝hose clamp screws 哈克钉huck bolts 旋锁螺丝ktx locking recess screws 机械螺丝machine screws mdf螺丝mdf screws 微小精密螺丝micro screws 钼六角螺丝mo hex head cap screws 钼nc螺丝mo nc fasteners 钼螺帽mo nuts 镍合金螺丝monel fasteners 多冲程螺丝multi-stage screw & parts 利革钉nylon plug & screws 单向螺丝one way lag screws 枋头中心螺丝pan head center bolts 面板螺丝panel fasteners 复合材料用螺丝(夹板用) particle board screws 贯穿螺丝penetrate screws 十字四角复合螺丝ph+sq combination screws 塑料螺丝plastic screws 犁壁螺丝plow bolts 特殊精密螺丝precision axis and special fasteners 卷带螺丝roll collated screws 屋顶螺丝roofing screws 螺旋椿screw studs 机(踏)车用螺丝.轴心screws & shafts for motorcycle or bicycle 针车用螺丝.轴心screws & shafts for sewing machine 螺丝附华司组合screws & washers assembled (sems) 安全螺丝security screws 钻尾螺丝self drillingscrews 自攻螺丝self tapping screws 固定螺丝screws & shafts for sewing machine 剪力钉shear concrete stud 束肩螺丝(栓) shoulder screws (bolts) 一字沟槽固定螺丝slotted set screws 止付螺丝socket set screws 飞机特殊扣件source control bolts 特殊涂装螺丝special coating screws 特长螺丝special longer screws 特殊材质螺丝special material screws 特殊螺丝special screws or bolts 特殊防松螺丝special self-locking screws 不锈钢特殊螺丝special stainless steel screws 特殊割尾螺丝special thread cutting screws 四角螺丝square head bolts 四角头固定螺丝square head set screws 不锈钢大螺丝stainless steel bolts 不锈钢塑板螺丝stainless steel chipboard screws 不锈钢粗牙螺丝stainless steel coarse thread screws 不锈钢旋入螺丝stainless steel drive screws 不锈钢平头内六角孔螺丝stainless steel flat head socket cap screws 不锈钢六角螺丝stainless steel hex head cap screws 不锈钢内六角螺丝stainless steel hex socket cap screws 不锈钢固定螺丝stainless steel hex socket set screws 不锈钢高低牙螺丝stainless steel high-low thread screws 不锈钢机械螺丝stainless steel machine screws 不锈钢小螺丝stainless steel screws 不锈钢钻尾螺丝stainless steel self drilling screws 不锈钢自攻螺丝stainless steel self tapping screws 不锈钢sems 螺丝stainless steel sems screws 不锈钢自削螺丝stainless steel thread cutting screws 不锈钢牙条棒stainless steel thread rod 不锈钢三角牙螺丝stainless steel triangular screw thread 不锈钢木螺丝stainless steel wood screws 卡锁壁虎steel locking anchor 大头马车螺丝step bolts 螺桩栓stud bolts t头螺丝t head bolts 扭矩控制螺栓t.c. bolts (tension control bolts) 自削螺丝thread cutting screws 牙条棒thread rod 姆指螺丝thumb screws 钛合金自行车螺丝titanium -6al –4r alloy fasteners 钛合金螺丝titanium alloy bolts 钛六角螺丝titanium hex head cap screws (hex bolts) 钛nc螺丝titanium nc fasteners 钛止付螺丝titanium set screws 钛内六角孔螺丝titanium socket cap screws 钛牙条titanium thread rod 套挂螺丝toggle bolts 套挂螺栓及螺丝toggle bolts & acoustical lag (screweye) 马桶螺丝toilet closet bolts torx screws torx screws 轨道螺栓(鱼尾螺丝) track bolts 三角牙螺丝triangular screws thread u型螺栓u bolts 直立轴螺丝vertical shaft screws 焊接螺丝weld studs,screws,bolts 焊点螺丝weld studs screws 轮毂螺栓wheel bolts 车轮轴螺丝,螺帽wheel hub bolts and nuts 窗户螺丝window screws 翼形螺丝wing screws 木螺丝wood screws 锆螺丝zr fasteners set screws set screws high strength bolts high strength bolts 铁盖焊接袋帽acorn cap nuts金属预置扭矩式螺帽all-metal prevailing torque type nuts 合金钢螺帽alloy steel nuts 铝螺帽aluminum nuts 壁虎螺帽anchor nuts 圆柱帽barrel nuts (cross dowel) 大尺寸螺帽big size nuts 铜螺帽brass nuts 四角多用途螺帽cage nuts 袋帽cap nuts 城堡螺帽castle nuts 齿花螺帽clinch nuts 铁盖袋帽closed end acorn nuts 盘形华司+袋帽螺帽conical washer and cap nuts 盘形华司螺帽conical washer nuts 耐候钢六角重型螺帽corten steel heavy hex nuts 长螺帽coupling nuts 铁盖+尼龙圈组合盖帽din 986 domed cap nuts 碟锁防松脱螺帽disk-lock nuts 企眼螺帽eye coupling nuts 环首螺帽eye nuts 突缘尼龙螺帽flange nylon insert lock nuts 平面华司螺帽flat washer nuts 齿轮gears六角重型螺帽heavy hex nuts 六角盖头螺帽hex cap nuts 六角突缘螺帽hex flange nuts薄型螺帽hex jam nuts 薄型电子六角螺帽hex jam nuts (for electronic) 机械螺丝用六角螺帽hex machine screw nut 普通六角螺帽hex nuts 六角锯齿螺帽hex serrated nuts 双头内牙螺帽hex (reducer )coupling nuts 高螺帽high nuts 高张力螺帽high strength nuts 内外牙螺母(拉帽) insert nuts jcn nuts jcn nuts 齿形螺帽kep nuts 防松螺帽lock nuts 长螺帽long nuts 机车用螺帽nuts for motorcycle 面板螺帽nuts plate 尼龙袋帽nylon cap insert lock nuts 尼龙嵌入防松螺帽nylon insert lock nuts 马桶螺帽open end acorn nuts 卡车轮胎螺帽outer cap nuts 管用螺帽pipe nuts 塑料螺帽plastic nuts pop nuts pop nuts 抑制螺帽prevailing torgue nut 快速扣件push nut fasteners 长方形螺帽(薄型) rectangle jam nuts 长方四角螺帽rectangle square nuts 圆螺帽round nuts 自锁螺帽self-locking nuts 制止螺帽sliding nuts sln-自锁防松螺帽sln self-locking nuts 沟槽螺帽slotted nuts 特殊螺帽special nuts 特殊轮毂螺帽special wheel nuts 弹簧螺帽spring nuts 薄型四角螺帽square jam nuts 四角螺帽square nuts 不锈钢突缘螺帽stainless steel flange nuts 不锈钢六角突缘尼龙螺帽stainless steel flange nylon insert lock nuts 不锈钢六角重型螺帽stainless steel heavy hex nuts 不锈钢六角螺帽stainless steel hex nuts 不锈钢螺帽stainless steel nuts 不锈钢尼龙嵌入螺帽stainless steel nylon insert lock nuts 不锈钢四角螺帽stainless steel square nuts 建筑用螺帽structural nuts t形螺帽t nuts 塑料品之埋植铜,铝螺帽threaded inserts for plastic injection mouldings 钛螺帽titanium nuts 压边螺帽+盘形华司组合top lock nut with conical washer assemble u形螺帽u nuts 焊接螺帽weld nuts 轮毂螺帽wheel nuts 蝶形螺帽wing nuts 锌压铸螺帽zinc die casting nuts 铝钉aluminum nails 马达轴承轴心组件bearing shaft（motor）轴承轴心bearing shaft 开口铆钉bifurcated rivets 长形拉帽（长型螺帽）binder posts（anchor nuts）拉帽blind nuts (rivet nuts) 拉钉blind rivets 电梯壁虎bolt anchor 金属黏着橡胶华司（双层华司）bonded washers 铜钉brass nails c型扣环c-rings 小眼钉ceiling hanger 化学壁虎chemical stud 实心梢clevis pins & straight pins 弹片clips 卷钉coil nails 冷锻零件cold forming part 开口梢cotter pins 洋钉钩cup hooks 弧型华司curved washer 外迫壁虎cut anchor 插梢dowel pin 捶钉drive rivet 壁虎drop in anchor e型环e-rings 膨胀螺栓expansion anchor bolts 难眼钉eyelets rivets 门钩gate hooks 插沟销grooved pins 有槽钢钉grooved steel nails 火药钉gunpowder nails 壁钩hardwall hangers 双片夹壁虎heavy duty shield anchor r型梢hitch pins（snap pins）空心钉hollow rivets 洋钉iron nails j钩j hook k.d. fitting k.d. fitting 闩锁latches & keeper assembleds 多冲程铆钉multi-stage rivers 锤钉壁虎nail in anchor 尼龙壁虎nylon (metal) frame anchor 塑料华司nylon washers 其它特殊铆钉other special rivets样品钩pegboard hook 吊图钩picture hangers 梢pins 各式管夹,管束pipe hanger 管塞pipe plug 塑料壁虎plastic nylon anchors pop拉钉系列产品pop rivets 快速插销quick release pins r型扣环r-rings 扣环rings 铆钉rivets 圆棒铁钉round iron nails t型铁钉round iron tape t nail 圆棒钢钉round steel nails t型钢钉round steel tape t nails u型钢钉round steel tape u nails 橡胶华司rubber washers s钩s hooks s型扣环s-rings 螺旋铝钉screw aluminum nails 螺旋环(洋眼) screw eyes 螺旋钩及螺旋圈screw hook & screwrings 螺丝钩screw hooks 螺旋铁钉screw iron nails 螺旋钢钉screw steel nails 中空铆钉semi-tubular rivet 套管壁虎sleeve anchor 实心铆钉solid rivets 特殊华司special washers 快速铆接扣件speed riveting 开叉钉split drive anchors 弹簧梢spring pin 弹簧华司spring washers 弹簧蝴蝶夹spring wings 折钉square hooks 不锈钢钢钉stainless steel nails 不锈钢中空钉stainless steel semi-tubular rivet 不锈钢斜纹钉stainless steel slanting stripes nails 不锈钢华司stainless steel washers 钢铁钉steel & iron nails 钢钉steel nails l型钢钉steel tape l nails 铁马钩storage hook 吸盘钩suction hangers 兰花钩swag hooks 三角吊钩swivel loop hangers 地毯钢钉tacked iron nails搓牙铁钉thread nails 大眼钉tie wire spade stud 钛合金铆钉titanium alloy rivets 钛合金膨涨螺丝titanium alloy expansion bolts 钛华司titanium washers 齿型华司tooth lock washers 管形铆钉tubular rivets 双向迫紧器turnbuckle 节牙钢钉w/strip steel nails 华司washers 波浪型华司wave washer 拉涨壁虎wedge anchor 线圈wire 锌合金壁虎zinc alloy frame anchor 螺丝,螺帽,五金,diy扣件all kinds of pacd aging series 合金钢工具alloy steel tools 电子手把handles for electronic devices 六角板手hexagon keys 螺丝起子power bit 螺丝起子screwdriver bit 电动螺丝起子autofeed screwdriver 工具套筒组件socket sets 套筒sockets 板手wrench 自动炼带螺丝枪autofeed screw driver 合金钢线材盘元alloy steel wire rod 铝合金锭aluminum alloy 球状化线材annealing wire & rod 黑铁丝black wire 黄铜棒线brass wire & rod 磨光棒钢bright steel bar (hex/round/square) 铜合金线copper alloy wire 线切割线e.d.m cutting wire 快削钢线材盘元free cutting steel wire rod 镀锌铁线galvanized steel wire 线材iron or steel wire 线材盘元iron or steel wire rod 洋白铜线nickel silver wire 磷青铜线phosphor bronze wire 各种表面处理用喷砂材料sand blasting materials 不锈钢条棒stainless steel bar (round/hex/square) 不锈钢冷锻线材stainless steel cold heading wire 不锈钢线(抽线后) stainless steel draw wire 不锈钢网线stainless steel net wire 不锈钢特殊线stainless steel special wire 不锈钢弹簧线stainless steel spring wire 不锈钢线材stainless steel wire 不锈钢线材及盘元stainless steel wire & rod 棒钢steel bar(hex/round/square) 钛、锆、钼、铌等螺丝、零件、材料ti、zr、mo、nb pare metal bolts parts 锌合金锭zinc alloy 立体/平面雕刻机3d die-sinking machine/engraving machine 转回90度辗线头机90°revolving wire twisting machine 干燥机air dryer 气动拉钉机air riveter 铝,低合金熔解热处理炉aluminum & low alloy melting furnace 铝散热器烧焊热处理炉aluminum brazing furnace for aluminum condenser 不锈钢线材连续式光辉热处理退火炉annealing furnace specially for stainless wire 小型脱油机anti-oil machine 自动包装机automatic packing machine 螺丝自动检查设备automatic screw sorting machine 自动送锁螺丝机automatic screwing machine 螺丝割尾加工机械automatic thread slotting machine 螺丝制造成型机械automatic trimming machine 箱式渗碳氮化炉batch type carburizing & mitriding furnace 钟罩式退火(球化)炉bell type spheroidizing annealing furnace 拉帽成型机blind nut formers 拉钉打头机blind rivet heading machine 螺丝(栓)成型机bolt formers 螺丝、螺帽成型机bolt formers, nut formers, headers 螺栓模bolt heading dies 螺丝、螺帽热处理bolt,nut & screws heat treatment 螺丝、螺帽热处理炉bolt,nut & screws heat treatment furnaces 圆剪式打头机bush cut-off heading machine 圆剪式空心打头机bush cut-off hollow heading machine 主模carbide dies 剪模carbide quills 不锈钢螺丝,扣件连续式光辉调质淬火炉carburizing furnace for stainless fastener 球状化电气炖炉carburizing furnace,vacuum & bell type furnace 流气式箱型炉(箱式,坑式,台车式,连续式) circulation furnace (box,pit,truck,continuous type) cnc计算机雕刻机cnc engraving machine 卷钉制造机coil nail collator 连续式光辉渗碳,淬火,回火炉continuous bright carburizing & hardening furnace 连续式光辉渗碳淬火炉continuous bright carburizing quenching furnace 连续式光辉调质淬火炉continuous bright hardening quenching furnace 中,高热镀锌光辉连续炉continuous bright heat treat furnace 连续式光辉热处理炉(不锈钢,硬焊) continuous bright treatment (for stainless,brazing) 连续式光辉热处理炉continuous type bright heat treatment furnace 耐腐蚀表面处理炉(耐炼) corrosion resistance of surface treatment furnace 剪刀(螺丝模) cut-off knives 集尘设备cyclone equipment 各种碳化钨制品设计制造design & manufacture of tungsten carbide products 模具dies & tools 钻尾模drill point dies 耐冲螺丝成型模具fastener forming dies 螺丝、螺帽品检量测仪器fasteners inspection and measurements’instruments 精密过滤器filter 滚沟牙板flat knurling dies 一般线材,盘元,退火炉general wire,wire rod annealing furnace 手动拉钉钳hand riveter 倒立式滑落型伸线机handstand type wire drawing machine 白铁针header punches for stainless bolt 三角,四角,六角针header punches in various drives(1) 米字,一字,梅花,零号针header punches in various drives(2)一字六角边冲头header punches in various drives(3) 螺丝打头机heading machine 六角冲针hex pins 六角冲模hex recess punches 六角冲模hex trimming dies 螺丝制造高速搓牙机械high speed automatic thread rolling machine 高中低周波感应加热炉high,medium,low frequency induction heater 空心打头机hollow heading machine 热锻造机hot former 冲销knockout pins 雷射/影像筛选机laser/optical sorting machine for screws 立式输送机loader 机械螺丝牙板machine screw thread rolling dies plates 冲床用的冲具manufacture of punch for press die 螺丝,螺帽用的冲具manufacture of punch making bolts and nuts 迷你成型机mini-formers 铁钉滚牙机nail rolling machine 铁钉模具nails die 成品自动收线机non-stop coiler 精抽自动收线机non-stop coiler (skinpass) 螺帽模nut forming dies 螺帽成型机nuts formers 螺帽攻牙机nuts tapping machine 特殊零件成型机parts forming machine 脚踏板系列自动组立专用机pedal automatic assembling machine 十字四角复合针ph+sq combination punches 四角十字冲模十字冲模phillips punches 十字割沟冲模phillips slotted punches 冲针壳pin holders 锁用中心零件pins tailpiece 拋光机/磨光台polishing machine 手握式螺丝自动供给锁紧机portable screw-driving machine 粉末治金烧结,黑化炉powder metallurgy & steam treatment furnace 米字冲模pozi punches 冲模punch dies 冲子punch pins 冲针冲床引伸模具punching dies 罗拉成型机rollers formers rx,dx瓦斯变成炉,ax 氨气分解炉rx,dx gas generator,ax ammo gas generator 盐浴式热处理炉salt bath heat treatment furnace各式表面处专用喷砂机sand blasting machine for surface treatment 螺丝自动组合华司机器screw & washer assembly machine for sems 机(踏)车用螺丝成型机screw for motorcycle or bicycle heading machine 螺丝夹尾模screws tail point dies 钻尾螺丝成型机self-drilling screw forming machine 钻尾模具self-drilling screw making dies 止付螺丝成型机set screws formers 梅花冲头six lobe punches 一字冲模slot punches 套筒成型机sockets formers 碳钢盘元,线材,球状化热处理退火炉spheroidizing annealing furnace for steel wire 一般线材,盘元,螺丝合金炖炉spheroidizing bright annealing furnace 球状化热理炉spheroidizing heat treatment furnace 四角孔针具sq punches 四角冲模square recess punches 不锈钢钻尾螺丝割尾stainless steel self drilling screw milled point 钻子tap 攻牙机tapping machine 自攻螺丝牙板tapping screw thread rolling dies plates 螺丝攻、车刀、模具taps dies & tools 铁氟龙(teflon)及珐琅烧付炉teflon coating furnace 搓牙机铁屑牙离装置thread chip separator 滚牙轮thread rolling dies 牙板thread rolling dies plates 螺丝搓手机thread rolling machine 精密油压滚牙机thread rolling machines 货物捆绑系统tie down hardware 弹簧机外围零件tooling peripheral component of spring machine 六角整头模trimming dies hexagon 碳化钨模具tungsten carbide die unilock self-locking and seal-locking unilock self-locking and seal-locking fasteners 电镀化学原料various electroplating chemicals 立式单双层连续伸线机vertical type single deck wire drawing machine 温锻造机warm former 伸线机wires drawer 特殊铆合扣件collars (a blind fastener for huck intl) 电器银接点contact point 螺丝diy包装系列diy screws packing series 自攻螺纹衬套ensat thread insert 螺丝、螺帽成型攻牙专用油forming& tapping oils for bolts & nuts formers 铰链hinges 热浸镀锌螺丝,螺帽hot dip galvanizing bolts & nuts 工业用炼industrial steel link chains 安全护套k-sert 机车离合器零件manufacture of motorcycle’s cvt parts 镜托mirror holders 螺丝套筒nut setters 尼龙头（用于螺丝头部）nylon head（for screws）尼龙圈（用于防松螺帽）nylon ring（for lock nuts）o.e.m. 组件o.e.m. parts 精密加工组件precise lathe cutting parts 精密车床零组件precision turning part 冲压零件punching parts 螺纹护套recoil inserts 轭铁(t型铁、u型铁) t-yoke,under yoke 喇叭头轭铁u-yoke,t-yoke for speaker 轮子零件wheel component 木螺丝牙板wood screw dies2005-11-16 22:30 315508161行业标准规范中英文对照系列之通用零部件(一)1 gb/t 2-1985 紧固件外螺纹零件的末端fasteners--ends of parts with external thread 2 gb/t 8-1988 方头螺栓c级square head bolts--product grade c 3 gb/t 10-1988 沉头方颈螺栓flat countersunk square neck bolts 4 gb/t 11-1988 沉头带榫螺栓flat countersunk nib bolts 5 gb/t 12-1988 半圆头方颈螺栓cup head square neck bolts 6 gb/t 13-1988 半圆头带榫螺栓cup head nib bolts 7 gb/t15-1988 大半圆头带榫螺栓cup head nib bolts with large head 8 gb/t 22-1976 小六角头导颈螺栓bolts, small hexagon head with fit neck 9 gb/t 23-1976 小六角头螺杆带孔螺栓bolts, small hexagon head with hole through the shank 10 gb/t 24-1976 小六角头螺杆带孔导颈螺栓Bolts, small hexagon head with fit neck and hole through the shank11 GB/T25-1976 小六角头头部带孔螺栓Bolts, small hexagon head with holes through the head 12 GB/T 26-1976 小六角头头部带孔导颈螺栓Bolts, small hexagon head with fit neck and holes through the head 13 GB/T 27-1988 六角头铰制孔用螺栓A和B级Hexagon fit bolts--Product grade A and B 14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓A和B级Hexagon fit bolts with Split pin hole on shank--Product grade A and B 15 GB/T 29.1-1988六角头头部带槽螺栓A和B级Hexagon bolts with slot on head--Product grade A and B 16 GB/T 29.2-1988 十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation 17 GB/T 31.1-1988 六角头螺杆带孔螺栓A和B级Hexagon bolts with split pin hole on shank--Product grade A and B 18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆B级Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B 19 GB/T31.3-1988 六角头螺杆带孔螺栓细牙A和B级Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B 20 GB/T 32.1-1988 六角头头部带孔螺栓A和B级Hexagon bolts with wire holes on head--Product grade A and B 21 GB/T 32.2-1988 六角头头部带孔螺栓细杆B级Hexagon bolts with wire holes on head--Reducedshank--Product grade B 22 GB/T 32.3-1988 六角头头部带孔螺栓细牙A和B级Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B 23 GB/T 35-1988 小方头螺栓B级Square head bolts with small head--Product grade B 24 GB/T 37-1988 T型槽用螺栓Bolts for T-Slot 25 GB/T 38-1976 螺栓技术条件Bolts--Technical requirements 26 GB/T 39-1988 方螺母C级Square nuts--Product grade C 27 GB/T41-1986 1 型六角螺母C 级Hexagon nuts--Style 1--Product grad C 28 GB/T 56-1988 六角厚螺母Hexagon thick nuts 29 GB/T 61-1976 螺母技术条件Nuts--Technical requirements 30 GB/T 62-1988 蝶形螺母Wing nuts31 GB/T 63-1988 环形螺母Lifting nuts 32 GB/T 65-1985 开槽圆柱头螺钉Slotted cheese head screws 33 GB/T 67-1985 开槽盘头螺钉Slotted pan head screws 34 GB/T 68-1985 开槽沉头螺钉Slotted countersunk head screws 35 GB/T 69-1985 开槽半沉头螺钉Slotted raised countersunk head screws 36 GB/T 70-1985 内六角圆柱头螺钉Hexagon socket cap head screws 37 GB/T 71-1985 开槽锥端紧定螺钉Slotted set screws with cone point 38 GB/T 72-1988 开槽锥端定位螺钉Slotted set screws with cone point 39 GB/T 73-1985 开槽平端紧定螺钉Slotted set screws with flat point 40 GB/T 74-1985 开槽凹端紧定螺钉Slotted set screws with cup point41 GB/T 75-1985 开槽长圆柱端紧定螺钉Slotted set screws withlong dog point 42 GB/T77-1985 内六角平端紧定螺钉Hexagon socket set screws with flat point 43 GB/T 78-1985 内六角锥端紧定螺钉Hexagon socket set screws with cone point 44 GB/T 79-1985 内六角圆柱端紧定螺钉Hexagon socket set screws with dog point 45 GB/T 80-1985 内六角凹端紧定螺钉Hexagon socket set screws with cup point 46 GB/T 83-1988 方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end 47 GB/T 84-1988 方头凹端紧定螺钉Square set screws with cup point 48 GB/T 85-1988 方头长圆柱端紧定螺钉Square set screws with long dog point 49 GB/T 86-1988 方头短圆柱锥端紧定螺钉Squareset screws with short dog point and cone end 50 GB/T 89-1976 螺钉技术条件Screws--Technical requirements51 GB/T 90-1985 紧固件验收检查、标志与包装Acceptance inspection,marking and packaging of fasteners 52 GB/T 91-1986 开口销Split pins 53 GB/T 93-1987 标准型弹簧垫圈Single coil spring lock washers--Normal type 54 GB/T 94.1-1987 弹性垫圈技术条件弹簧垫圈Specifications for spring washers--Single coil spring lock washers 55 GB/T 94.2-1987 弹性垫圈技术条件齿形、锯齿锁紧垫圈Specifications for spring washers--Toothed lock and serrated lock washers 56 GB/T94.3-1987 弹性垫圈技术条件鞍形、波形弹性垫圈Specifications for springwashers--Curved and wave spring washers 57 GB/T 95-1985 平垫圈-C级Plainwashers--Product grade C 58 GB/T 272-1993 滚动轴承代号方法Rollingbearing--Identification code 59 GB/T 273.1-1987 滚动轴承圆锥滚子轴承外形尺寸方案Rolling bearings Tapered roller bearings--Boundary dimensions 60 GB/T 273.3-1988 滚动轴承向心轴承外形尺寸方案Rolling bearings Radial bearings—Boundary dimensions 61 GB/T 274-1991 滚动轴承装配倒角极限Rolling bearing chamfer dimension limits 62GB/T 275-1993 滚动轴承与轴和外壳的配合Shaft and housing fits for rolling bearings 63 GB/T 276-1994 滚动轴承深沟球轴承外形尺寸Rolling bearings--Deep groove ball bearings--Boundary dimensions 64 GB/T 280-1964 带毡封圈的单列向心球轴承结构型式和基本尺寸Rolling bearings--Single-row radial ball bearings withfelt seals--Types and basic dimensions 65 GB/T 281-1994 滚动轴承调心球轴承外形尺寸Rollingbearings--Self-aligning ball bearings--Boundary dimensions 66 GB/T 283-1994 滚动轴承圆柱滚子轴承外形尺寸Rolling bearings--Cylindrical roller bearings—Boundary dimensions 67 GB/T 285-1994 滚动轴承双列圆柱滚子轴承外形尺寸Rolling bearings--Double row cylindrical roller bearings—Boundary dimensions 68 GB/T 286-1964 双列向心球面滚子轴承结构型式和基本尺寸Rolling bearings--Double -row radial spherical roller bearings--Types and basic dimensions 69 GB/T 288-1994 滚动轴承调心滚子轴承外形尺寸Rolling bearings--Self-aligning roller bearings—Boundary dimensions 70 GB/T 289-1964 滚针轴承结构型式和基本尺寸Needle roller bearings--Types and basic dimensions 71 GB/T 291-1964 螺旋滚子轴承结构型式和基本尺寸Rolling bearings with helically wound cylindrical rollers--Types and basic dimensions 72 GB/T 292-1994 滚动轴承角接触球轴承外形尺寸Rolling bearings--Angular contact ball bearings--Boundary dimensions 73 GB/T 294-1994 滚动轴承三点和四点接触球轴承外形尺寸Rolling bearings--Three point and four point contact ball bearings--Boundary dimensions 74 GB/T 296-1994 滚动轴承双列角接触球轴承外形尺寸Rolling bearings--Double row angular contact ball bearings--Boundary dimensions 75 GB/T 297-1994 滚动轴承圆锥滚子轴承外形尺寸Rolling bearings--Tapered roller bearings--Boundary dimensions 76 GB/T299-1995 滚动轴承双列圆锥滚子轴承外形尺寸Rolling bearings--Metric double row tapered roller bearings--Boundary dimensions 77 GB/T 300-1995 滚动轴承四列圆锥滚子轴承外形尺寸Rolling bearings--Four row tapered roller bearings--Boundary dimensions 78GB/T 301-1995 滚动轴承推力球轴承外形尺寸Rolling bearings--Thrust ballbearings--Boundary dimensions 79 GB/T 304.1-1988 关节轴承分类Spherical plain bearings Classification 80 GB/T 304.2-1988 关节轴承代号方法Spherical plain bearings Identification code81 GB/T 304.3-1990 关节轴承配合Spherical plain bearings—Fits 82 GB/T 304.9-1981 向心关节轴承技术条件Spherical plain radial bearings, jointtype--Technical requirements 83 GB/T 304.10-1989 关节轴承公差Spherical plain bearings—Tolerances 84 GB/T 307.1-1994 滚动轴承向心轴承公差Rollingbearings--Radial bearings--Tolerances 85 GB/T 307.2-1995 滚动轴承测量和检验的原则及方法Rolling bearings--Measuring and gauging principles and methods 86 GB/T307.3-1996 滚动轴承通用技术规则Rolling bearings--General technical regulations 87 GB/T 307.4-1994 滚动轴承推力球轴承公差Rolling bearings--Thrust ballbearings--Tolerances 88 GB/T 308-1989 滚动轴承钢球Rolling bearings—Steel balls 89 GB/T 309-1984 滚动轴承滚针Rolling bearings--Needle rollers 90 GB/T 794-1993 加强半圆头方颈螺栓Strengthened cap head square neck bolts 91 GB/T 798-1988 活节螺栓Eye bolts 92 GB/T 799-1988 地脚螺栓Eyelet bolts 93 GB/T 800-1988 沉头双榫螺栓Flat countersunk double nib bolts 94 GB/T 802-1988 组合式盖形螺母Acorn nuts 95 GB/T804-1988 球面六角螺母Hexagon nuts with raised face 96 GB/T 805-1988 扣紧螺母Tight nuts 97 GB/T 806-1988 滚花高螺母Knurled nut with collar 98 GB/T 807-1988 滚花薄螺母Knurled nuts 99 GB/T 808-1988 小六角特扁细牙螺母Small hexagon thinnuts-Fine pitch thread 100 GB/T 809-1988 嵌装圆螺母Insert round nuts2005-11-16 22:32 315508161行业标准规范中英文对照系列之通用零部件(二)101 GB/T 810-1988 小圆螺母Small round nuts 102 GB/T 812-1988 圆螺母Round nuts 103 GB/T 815-1988 端面带孔圆螺母Round nuts with drilled holes in one face 104 GB/T 816-1988 侧面带孔圆螺母Round nuts with set pin holes in side 105 GB/T 817-1988 带槽圆螺母Slotted round nuts 106 GB/T 818-1985 十字槽盘头螺钉Cross recessed pan head screws 107 GB/T 819-1985 十字槽沉头螺钉Cross recessed countersunk head screws 108 GB/T 820-1985 十字槽半沉头螺钉Cross recessed raised countersunk head screws 109 GB/T 821-1988 方头倒角端紧定螺钉Square set screws with chamfered end 110 GB/T 822-1988 十字槽圆柱头螺钉Cross recessed cheese head serews 111 GB/T 823-1988 十字槽小盘头螺钉Cross recessed small pan head screws 112 GB/T 824-1976 圆柱头内花键螺钉Screws,fluted socket head 113 GB/T 825-1988 吊环螺钉Eyebolts 114 GB/T 827-1986 标牌铆钉Rivets for name plate 115 GB/T 828-1988 开槽盘头定位螺钉Slotted pan head set setscrews with dog point 116 GB/T 829-1988 开槽圆柱端定位螺钉Slotted setscrews with dog point 117 GB/T 830-1988 开槽圆柱头轴位螺钉Slotted cheese head screws with shoulder 118 GB/T 831-1988 开槽无头轴位螺钉Slotted shoulder screws 119 GB/T 832-1988 开槽带孔球面圆柱头螺钉Slotted capstan screws 120 GB/T 833-1988 开槽大圆柱头螺钉Slotted large cheese headscrews121 GB/T 834-1988 滚花高头螺钉Knurled thumb screws 122 GB/T 835-1988 滚花平头螺钉Knurled screws 123 GB/T 836-1988 滚花小头螺钉Knurled screws with small head 124 GB/T 837-1988 开槽盘头不脱出螺钉Slotted pan head screws with waisted shank 125 GB/T 838-1988 六角头不脱出螺钉Hexagon screws with waisted shank 126 GB/T 839-1988 滚花头不脱出螺钉Knurled thumb screws with waisted shank 127 GB/T 840-1988 塑料滚花头螺钉Plastic diamond knurlhead screws 128 GB/T 845-1985 十字槽盘头自攻螺钉Cross recessed pan head tapping screws 129 GB/T 846-1985 十字槽沉头自攻螺钉Cross recessed countersunk head tapping screws 130 GB/T 847-1985 十字槽半沉头自攻螺钉Cross recessed raised countersunk head tapping screws 131 GB/T 848-1985 小垫圈--A级Plain washers--Small series--Product grade A 132 GB/T 849-1988 球面垫圈Weshers with ball face 133 GB/T 850-1988 锥面垫圈Washers with cone face 134 GB/T 851-1988 开口垫圈Washers with split 135 GB/T 852-1988 工字钢用方斜垫圈Square taper washers for I section 136 GB/T 853-1988 槽钢用方斜垫圈Square taper washers for slot section 137 GB/T 854-1988 单耳止动垫圈Tab washers with long tab 138 GB/T855-1988 双耳止动垫圈Tab washers with long tab and wing 139 GB/T 856-1988 外舌止动垫圈External tab washers 140 GB/T 858-1988 圆螺母用止动垫圈Tab washers for round nut141 GB/T 859-1987 轻型弹簧垫圈Single coil spring lock washers,Light type 142 GB/T 860-1987 鞍形弹性垫圈Curved spring washers 143 GB/T 861.1-1987 内齿锁紧垫圈Lock washers internal teeth 144 GB/T 861.2-1987 内锯齿锁紧垫圈Serrated lock washers internal teeth 145 GB/T 862.1-1987 外齿锁紧垫圈Lock washers external teeth 146 GB/T 862.2-1987 外锯齿锁紧垫圈Serrated lock washers external teeth 147 GB/T863.1-1986 半圆头铆钉(粗制) Round head rivets--Black 148 GB/T 863.2-1986 小半圆头铆钉(粗制) Round head rivets with small head--Black 149 GB/T 864-1986 平锥头铆钉(粗制) Cone head rivets--Black 150 GB/T 865-1986 沉头铆钉(粗制) Countersunk head rivets-Black151 GB/T 866-1986 半沉头铆钉(粗制) Oval countersunk head rivets--Black 152 GB/T 867-1986 半圆头铆钉Round head rivets 153 GB/T 868-1986 平锥头铆钉Cone head rivets 154 GB/T 869-1986 沉头铆钉Countersunk head rivets 155 GB/T870-1986 半沉头铆钉Oval countersunk head rivets 156 GB/T 871-1986 扁圆头铆钉Flat round head rivets 157 GB/T 872-1986 扁平头铆钉Thin head rivets 158 GB/T 873-1986 扁圆头半空心铆钉Oval head semi-tubular rivets 159 GB/T 874-1986 120°沉头半空心铆钉120 degree countersunk head semi-tubular rivets 160 GB/T 875-1986 偏平头半空心铆钉Thin head semi-tubular rivet161 GB/T 876-1986 空心铆钉Tubular rivets 162 GB/T877-1986 开尾圆锥销Taper pins with split 163 GB/T 878-1986 螺纹圆柱销Parallel pins with external thread 164 GB/T 879-1986 弹性圆柱销Spring-type straight pins—Slotted 165 GB/T 880-1986 带孔销Pins with split pin hole 166 GB/T 881-1986 螺尾锥销Taper pins with external thread 167 GB/T 882-1986 销轴Clevis pins with head 168 GB/T883-1986 锥销锁紧挡圈Lock rings with cone pin 169 GB/T 884-1986 螺钉锁紧挡圈Lock ring with screw 170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈Lock rings with screwand circlip 171 GB/T 886-1986 轴肩挡圈Rings for shoulder 172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts (with non-metallic insert),style 1 173 GB/T 891-1986 螺钉紧固轴端挡圈Lock rings at the end of shaft with screw 174 GB/T 892-1986 螺栓紧固轴端挡圈Lock rings at the end of shaft with bolt 175 GB/T 893.1-1986 孔用弹性挡圈--A型Circlips for holes--Type A 176 GB/T 893.2-1986 孔用弹性挡圈--B型Circlips for hole--Type B 177 GB/T 894.1-1986 轴用弹性挡圈--A型Circlips forshaft--Type A 178 GB/T 894.2-1986 轴用弹性挡圈--B型Circlips for shaft--Type B 179 GB/T 895.1-1986 孔用钢丝挡圈Roundwire snap rings for hole 180 GB/T 895.2-1986 轴用钢丝挡圈Roundwire snap rings for shaft 181 GB/T 896-1986 开口挡圈"E" rings 182 GB/T 897-1988 双头螺柱bm=1d Double end studs--bm=1d 183 GB/T 898-1988 双头螺柱bm=1.25d Double end studs bm=1.25d 184 GB/T 899-1988 双头螺柱bm=1.5d Double end studs bm=1.5d 185 GB/T 900-1988 双头螺柱bm=2d Double end studs bm=2d 186 GB/T 901-1988 等长双头螺柱B级Double end studs (clamping type)--Product grade B 187GB/T 902.1-1989 手工焊用焊接螺柱Weld studs for manual welding 188 GB/T 902.2-1989 机动弧焊用焊接螺柱Weld studs for arc welding 189 GB/T 902.3-1989 储能焊用焊接螺柱Weld studs for capacitor discharge welding 190 GB/T 921-1986 钢丝锁圈Round wire circlips 191 GB/T 922-1986 木螺钉技术条件Specifications for wood screws 192 GB/T 923-1988 盖形螺母Acorn nuts 193 GB/T 925-1988 轻型六角自锁螺母Self-locking nuts,hexagon light 194 GB/T 927-1988 球面六角自锁螺母Self-locking nuts,hexagon sphere 195 GB/T 929-1988 单耳托板自锁螺母Self-locking nuts,singlelug, anchor 196GB/T 930-1988 双耳托板自锁螺母Self-locking nuts,twolug, anchor 197 GB/T 931-1988 角形托板自锁螺母Self-locking nuts,angle, anchor 198 GB/T 932-1988 气密单耳托板自锁螺母Self-locking nuts,singlelug, anchor, sealing, 199 GB/T 933-1988 气密双耳托板自锁螺母Self-locking nuts,twolug, anchor, sealing 200 GB/T 937-1988 成组游动托板自锁螺母Self-locking nuts, anchor, floating,Gang channel2005-11-16 22:33 315508161行业标准规范中英文对照系列之通用零部件(三) 201 GB/T 938-1988 游动自锁螺母Self-locking nuts, floating 202 GB/T 939-1988 单耳托板自锁螺母保护罩Boots forself-locking nuts, singlelug, anchor 203 GB/T 940-1988 双耳托板自锁螺母保护罩Boots for self-locking nuts,twolug, anchor 204 GB/T 941-1988 角形托板自锁螺母保护罩Boots for self-locking nuts,angle, anchor 205 GB/T 943-1988 自锁螺母技术条件Procurement specification for self-locking nuts 206 GB/T 945-1976 十字槽球面中柱头螺钉Screws,cross recessed,thin raised cheese head 207 GB/T 946-1988 开槽球面圆柱头轴位螺钉Slotted raised cheese head with shoulder 208 GB/T 947-1988 开槽球面大圆柱头螺钉Slotted large raised cheese head screws 209 GB/T 948-1988 开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank 210 GB/T 949-1988 开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank211 GB/T 950-1986 十字槽圆头。
常用紧固件相关英语(中英对照)
螺纹大径：Major Diam中径：Pitch diam底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punching1 标准GB （国标）DIN （德制）JIS （日标）ANSI （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈6-bobes recess 内梅花BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头欧洲标准EN国际标准化组织国际标准化组织标准ISO 国际电工委员会国际电工委员会标准IEC 国际国际电信联盟标准ITU欧共体欧洲电子元器件协会标准CECC德国德国标准DIN英国英国标准BS美国美国国家标准ANSI美国美国材料与试验协会标准ASTM美国美国机械工程师协会标准ASME美国美国电子工业协会标准EIA美国美国连接电子学工业协会标准IPC美国美国焊接协会标准AWS美国美国石油协会标准API美国美国国家公路与运输商协会标准AASHTO美国美国加热制冷与空调工程师协会标准ASHRAE 美国美国电气制造商协会标准NEMA美国美国给水工程协会标准AWWA美国美国仪器、系统与自动化协会标准ISA美国美国保险商实验室标准UL美国电气与电子工程师协会标准IEEE美国美国机动工程师协会标准SAE美国美国腐蚀工程师协会标准NACE美国美国纺织化学师与印染师协会标准AATCC美国美国钢结构油漆标准SSPC美国美国铝协会标准AA美国美国卫生工程协会标准ASSE美国美国煤气协会标准AGA美国美国阀门及配件工业协会标准MSS美国美国音频工程协会标准AES美国美国建筑小五金制造商协会标准BHMA美国美国国家卫生基金会标准NSF美国美国标准NISO,PFI,RWMA美国美国信息与图像管理协会标准AIIM美国美国空调与制冷学会标准ARI美国美国军用标准MIL美国美国防火协会标准NFPA美国美国航空无线电设备标准ARINC美国美国齿轮协会标准AGMA加拿大加拿大标准协会标准CSA加拿大加拿大通用标准局标准CGSB澳大利亚澳大利亚国家标准AS德国德国工程师协会标准VDI欧共体欧洲电信标准ETSI法国法国标准NF日本日本工业标准JIS中国国家标准GB中国机械工业标准JB 中国电子工业标准SJ。
常用紧固件相关英语(中英对照).
螺纹大径:Major Diam中径:Pitch diam底径:Minor diam通止规:Go/No go gage机械性能:mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢,防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料:Raw material球化退火:Annealing冷拔:Drawing冷镦:Forming机加工:Machining螺纹成型:Roll Threading热处理:heat-treatment表面处理:finish去氢:Lustrating hydrogen检验:Inspection包装:Packing入库:Stocking车床:lathe磨制:grinding红打:hot forging冲压:punching1 标准GB (国标DIN (德制JIS (日标ANSI (美标BA (英制2 螺纹M. MF (公制牙UNC.UNF (美制牙BSW.BSF (英制牙3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈6-bobes recess 内梅花BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头欧洲标准EN国际标准化组织国际标准化组织标准ISO 国际电工委员会国际电工委员会标准IEC 国际国际电信联盟标准ITU欧共体欧洲电子元器件协会标准CECC德国德国标准DIN英国英国标准BS美国美国国家标准ANSI美国美国材料与试验协会标准ASTM美国美国机械工程师协会标准ASME美国美国电子工业协会标准EIA美国美国连接电子学工业协会标准IPC美国美国焊接协会标准AWS美国美国石油协会标准API美国美国国家公路与运输商协会标准AASHTO美国美国加热制冷与空调工程师协会标准ASHRAE 美国美国电气制造商协会标准NEMA美国美国给水工程协会标准AWWA美国美国仪器、系统与自动化协会标准ISA美国美国保险商实验室标准UL美国电气与电子工程师协会标准IEEE美国美国机动工程师协会标准SAE美国美国腐蚀工程师协会标准NACE美国美国纺织化学师与印染师协会标准AATCC美国美国钢结构油漆标准SSPC美国美国铝协会标准AA美国美国卫生工程协会标准ASSE美国美国煤气协会标准AGA美国美国阀门及配件工业协会标准MSS美国美国音频工程协会标准AES美国美国建筑小五金制造商协会标准BHMA 美国美国国家卫生基金会标准NSF美国美国标准NISO,PFI,RWMA美国美国信息与图像管理协会标准AIIM美国美国空调与制冷学会标准ARI美国美国军用标准MIL美国美国防火协会标准NFPA美国美国航空无线电设备标准ARINC美国美国齿轮协会标准AGMA加拿大加拿大标准协会标准CSA加拿大加拿大通用标准局标准CGSB澳大利亚澳大利亚国家标准AS德国德国工程师协会标准VDI欧共体欧洲电信标准ETSI法国法国标准NF日本日本工业标准JIS中国国家标准GB中国机械工业标准JB 中国电子工业标准SJ。
紧固件专用词中英文对照
ZB ZBK ZY (ZO) ZW Sil Plat Nic Plat Dacr HDZinc
兰锌 黑锌 黄锌 白锌 镀银 镀镍 达克罗 热浸锌
常用英文单词及简写形式
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 单词 screw nut washer head thread coating rivet standoff driver hexagon tooth lock spring wave pitch partial thread PT Full Thread silver cone Eco-syn Thread Forming Self Tapping pin shaft steel stainless steel Brass(Cu) Aluminum Rubber machine screw SEM screw Material Grade Finish Point Clamp internal external thickness length hole Metric DIN ANSI JIS ISO NFE GB Quality 简写 scr nut wash hd thre coat riv stdoff driv hexa tooth lck spr wave pitch PT PT FT silv cone Eco TF self tapp pin Shaf St SS Bras(Cu) AL Rub mech scr SEM Scr material GD Finish Point Clam Int ext / / / Metcric / / / / / / / 中文 螺丝 螺母 垫圈 头 螺纹 镀层 铆钉 内外六角钉 穴 六角 齿 锁 弹簧 波浪型 牙距 半螺纹 一种螺纹形式 全螺纹 银 锥形 30度牙的一种螺纹 自攻螺纹 自切屑螺纹 销 轴 铁 不锈钢 铜 铝 橡胶 机制螺丝 组合螺丝 材料 等级 表面处理 点 夹子 内 外 厚度 长度 孔 公制 德标 美标 日标 国际标准 法标 国家标准 质量
常用紧固件行业相关术语(中英对照)简体
常用紧固件行业相关术语(中英对照)简体.txt丶︶￣喜欢的歌，静静的听，喜欢的人，远远的看我笑了当初你不挺傲的吗现在您这是又玩哪出呢？组装、冲压、喷漆等专业词匯Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley臺车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生產部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 銼毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿臺Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生產力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动啟子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿臺head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生銹deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off臟污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生產equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 準备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生產单位lots of production生產批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氬焊vocabulary for stamping冲压常词匯stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset復位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履歷卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标準件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词匯die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die復合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘復棹人second count 復盘人second check復盘復核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 復盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据匯总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核準/审核/承办PCE assembly production schedule sheetPCE组装厂生產排配表model机钟work order工令revision版次remark备注production control confirmation生產确认checked by初审approved by核準department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head掛鉤槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶桿spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除銹机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连桿edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate鈑金lathe车mill銼plane刨grind磨drill铝boring鏜blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生產进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel鉬高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies復合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶桿trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶桿spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头鉤销(拉料桿) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投產前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回復内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水準S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标準S I-S IV Special I-Special IV 特殊抽样水準等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水準RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生產管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标準CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 臺湾IWS International Workman Standard 工艺标準ISO International Standard Organization 国际标準化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq產品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq產品在龙华组装厂品管作业规范CQCP P-Painting Compaq產品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 產品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生產部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生產类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生產单D/C Date Code 生產日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本復印相关人员APP Approve 核準,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生產前準备时间)S/T Standard Time 标準时间P/M Product Market 產品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标準体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标準结构SIMM Single in-line memory module 单项导通匯流组件DIMM Dual in-line Memory Module 双项导通匯流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生產保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 復合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ?泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 鉍铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 復合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 復式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 復板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 軛型模模具厂常用之标準零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整桿 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出桿ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶?lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板 moving bolster 换模保持装置moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导?pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推桿 pusher pin 衬套梢rack 机架 rapping rod 起模桿re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 托料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料? spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 托板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
紧固件专业英语词汇螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度1 标准GB （国标）ISO(国际标准)DIN （德制）JIS （日标）ANSI /ASME （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cup head square neck bolts 半圆头方螺栓Cup head nib bolts 半圆头带榫螺栓Cup head square neck bolts with large head –product grade C大半圆头方颈螺栓C级Hexagon head bolts-product grade C六角头螺栓C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆菌B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员B级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉合金鋼線材盤元alloy steel wire rod球狀化線材annealing wire and rod黑鐵絲black wire黃銅棒線brass wire and rod磨光棒鋼bright steel bar(hex/round/square)銅合金線copper alloy wire線切割線 e.d.m cutting wire快削鋼線材盤元free cutting steel wire rod線材iron or steel wire線材盤元iron or steel wire rod洋白銅線 nickel silver wire磷青銅線phosphate bronze wire不鏽鋼條棒stainless steel bar(round/hex/square)不鏽鋼冷鍛線材stainless steel cold heading wire不鏽鋼線(抽線後) stainless steel draw wire不鏽鋼線材stainless steel wire不鏽鋼線材及盤元stainless steel wire and rod棒鋼steel bar(hex/round/square)轉回90度碾線頭機 90訌evolving wire twisting machine氣動拉釘機air riveter各式螺絲類產品自動包裝automatic packaging for all kinds of packaging 自動包裝機automatic packing machine螺絲製造搓牙機械automatic thread rolling machine螺絲割尾加工機械automatic thread slotting machine螺絲製造成型機械automatic trimming machine拉釘打頭機blind rivet heading machine螺絲、螺帽成型機bolt formers,nuts formers,headers螺絲、螺帽熱處理bolt nut and screws heat treatment螺絲、螺帽熱處理爐bolt nut and screws heat treatment furnaces球狀化電器燉爐carburizing furnace vacuum and bell type furnace超防銹復合瓷膜ceramic coating連續式光輝滲碳淬火爐continuous bright carburizing quenching furnace連續式光輝?#123;質淬火爐continuous bright hardening quenching furnace中、高熱鍍鋅光輝連續爐continuous bright heat treat furnace連續式光輝熱處理爐continuous type bright heat treatment furnace 螺絲割尾及特殊割遘加工machine screw shank slotting螺絲鑽孔加工screw shank drilling雞眼上下模eyelets dies一般線材、盤元、退火爐general wire,wire rod,annealing furnace 倒立式滑落型伸線機handstand type wire drawing machine十字沖模header punches in various drives成型沖模header punches in various drives螺絲打頭機heading machine螺絲製造高速搓牙機械high speed automatic thread rolling machine 高中低周波感應加熱爐high,medium,low frequency induction heater 空心打頭機hollow heading machine熱浸鍍鋅螺絲、螺帽hot dip galvanizing bolts and nuts機械鍍鋅mechanical galvanized迷你成型機mini-formers成品自動收線機 non-stop coiler精抽自動收線機 non-stop coiler(skinpass)螺帽模 nut forming dies螺帽成型模 nuts formers特殊零件成型機parts forming maching沖模punch dies沖子punch pins。