FN-303S胶粘剂使用说明书
3M公司结构胶黏剂使用指南1
3M公司结构胶黏剂使用指南13M公司结构胶黏剂使用指南高性能腈类塑料粘合剂1099·1099-L特征：·3M公司的结构胶黏剂1099是一款中等粘度的适用于大多数涂刷程序的高性能腈类塑料粘合剂；·3M公司的结构胶黏剂1099-L是一款低粘度喷涂程序的高性能腈类塑料粘合剂；·固化速度快；·粘接强度和柔韧性好；·抗风化、水、溶剂、石油和增塑剂；·可粘接浅色的乙烯基材质；·也可粘接纤维，泡沫和许多塑料(不建议用于聚烯烃塑料)；·加热固化可以获得更优异的物理性能。
特殊物理性能（备注：以下技术信息和数据只能被视为代表或典型，不应该用于规范目的）产品3M公司结构胶黏剂使用指南高性能腈类塑料粘合剂1099 1099-L粘度（近似值）：布氏剩余容量参数@ 80o F(27o C)2000-4000 cps.(#3 sp @ 10 rpm)200-325 cps.(#2 sp @ 20 rpm)固体含量（质量分31-37% 22-26%数）：基底：丁腈橡胶丁腈橡胶颜色（干或湿）：淡棕褐色淡棕褐色净重（近似值）：7.3-7.5 磅/加仑7.0-7.4 磅/加仑（磅/加仑)闪点(密闭杯): 0o F (-18o C) 0o F (-18o C) 溶剂：丙酮丙酮和甲基乙基酮粘结时间：达40分钟达20分钟覆盖范围：456 sq. ft./gal 313 sq. ft./gal (@ 2.5g/ft.2 dry wt.)处理/应用信息使用说明：1.表面处理：擦净所有灰尘、污垢、油、油脂、蜡、松动的油漆，等等。
用甲基乙基酮或3M公司的橙香清洁剂有助于处理粘结表面。
2.使用温度：粘结的最佳温度为65o F (18o C)。
3.应用：使用前搅拌均匀多孔表面：刷、喷涂薄层，甚至一个或两个表面都可喷涂胶粘剂。
在粘结前两面都喷涂胶黏剂会产生更大的强度，并允许长时间打开。
预涂卷材涂料涂装工艺对涂膜性能的影响
化学转化膜是一层化学稳定性较高 、组织致密的 膜层 ,具有隔离 、屏蔽作用 ,使金属表面与腐蚀介质隔 离 ,也起封闭作用 ,从而提高卷材的耐腐性并增加涂 膜与基材的附着力 。不同金属的卷材应使用不同的 化学转化处理剂 。常用的处理剂有磷酸盐型 、铬酸盐 型 、复合金属氧化物型 。在辊涂法转化处理工艺中 , 最常用的处理剂是铬酸盐型 。 2. 1 铬酸盐转化处理对钢板性能的影响
产工艺 。 预涂金属卷材的最大的应用领域是建筑业 ,但由
于其良好的经济效益和能适应社会经济 、环保发展的 需要 ,近年来在家电行业的使用量也明显增加 ,随着 技术的进步 ,还将扩展到交通运输等领域 。
预涂卷材涂料的质量不仅取决于涂料本身的性 能 ,涂装工艺的控制对涂膜的性能也有很大的影响 。
表 2 试 验 数 据
由表 1中的试验结果可以看出 ,在冷轧钢板上 , 涂膜的耐 M EK擦拭性能主要受涂膜的交联密度影 响 ,有无化学处理对涂膜的耐 M EK擦拭性能影响不 大 。但是化学处理对涂膜与基板的附着力以及基板 的耐腐蚀性能影响较大 。对基板进行化学处理 ,可以 提高涂膜与基板间的附着力 ,从而改善涂膜的 T弯
表 6 涂装线速与涂膜性能的关系
涂装线速 / (m ·m in - 1 ) 40 60 80
耐 M EK擦拭 (往返 ) /次 > 100 90 80
3M 胶粘剂与密封剂使用手册说明书
4[ 30 ]GASKETINGadhesives & sealants guide [ volume 5 ]LOCTITE ® GASKET SEALANT 1 –HARD SETTING Reliable, paste-like gasket sealant/dressing/coating. Dries quickly to a hard set. Recommended for rigid, permanent assemblies. Temperature range: -65°F to 400°F (-54°C to 204°C); resists common shop fluids and fuels.Typical Applications: Anti-freeze plugs, threaded connections, manifold gaskets.Item Container Size Pack 37541 1.5 oz. tube 12375423 oz. tube12LOCTITE ® GASKET SEALANT 2 –NON-HARDENING Reliable, paste-like gasket sealant/dressing/coating. Sets more slowly to a pliable film. Best suited for non-rigid, vibrating assemblies. Allows for easy disassembly if required. Temperature range: -65°F to 400°F (-54°C to 204°C); resists common shop fluids and fuels. Typical Applications: Valve cover gaskets, oil pan gaskets.Item Container Size Pack 37543 1.5 oz. tube 12375443 oz. tube12LOCTITE ® COPPER GASKET ADHESIVE – HI-TEMP ADHESIVE SEALANTFast-drying, metallic copper sealant helps dissipate heat, prevents gasket burnout and improves heat transfer.Seals instantly. Fills hot spots and surface imperfections. Temperature range: -50°F to 500°F (-46°C to 260°C); resists all types of automotive fluids, especially gasoline.Typical Applications: Cylinder head gaskets, carburetor gaskets, exhaust manifold gaskets and other high temperature applications.Item Container Size Pack 375839 oz. aerosol can12LOCTITE ® AVIATION GASKET SEALANT – GASKET DRESSINGSlow-drying, non-hardening brushtop sealant approved for use in aviation as well as automotive applications. Temperature range: -65°F to 400°F (-54°C to 204°C); resists gasoline, oil and grease.Typical Applications: Close-fitting machined surfaces, sealing hoses, solid gaskets.Item Container Size Pack 37559 4 oz. brushtop can 123755816 oz. brushtop can12LOCTITE ® HI-TACK GASKET SEALANT – GASKET DRESSINGFast-drying sealant dries to a highly tacky, non-brittle film that holds gaskets in place during assembly. Temperature range: -65°F to 500°F (-54°C to 260°C); resists gasoline, oil, antifreeze, axle lube.Typical Applications: Valve covers, fuel pumps, carburetors, manifold gaskets.Item Container Size Pack 37554 4 oz. brushtop can 1237555 9 oz. aerosol can 123755316 oz. brushtop can12PERFORMANCE GASKET TYPEGasketing Selector ChartsProperties Chart: Gasketing* Uncured liquid adhesives may cause stress cracking of certain thermoplastics (e.g., polycarbons, acrylic and polysulfone).4[ 32 ] GASKETINGat 200 mphthere are no second choices.M&M‘S, M and the M&M‘S Characters are trademarks of Mars, Incorporated and its affiliates. © Mars, Inc. 2007. Manufactured and distributed underlicense by Henkel Corporation. Robert Yates Racing is used under license. Loctite is a registered trademark of Henkel Corporation, U.S.A. © Copyright 2007. Henkel Corporation. All rights reserved.At speeds exceeding 190 mph, we can’t afford to have anyleaks or loose fasteners on our cars. To survive the brutal stress and vibration that each race throws at us, we depend on Loctite® gasketing products to keep us on track.”– Robert Yates“THERE IS NO SECOND CHOICE.。
SureHold单用超级粘合剂用户手册说明书
Revision 0Revision Date 18-Nov-2014 Barristo Enterprises, Inc., dba SureHold®SAFETY DATA SHEETSingle Use Super GlueProduct Name Single Use Super Glue, 3 Pack, 4 Pack, 5 PackPart Number SH-373, SH-374-SH-378Company Barristo Enterprises, Inc. dba SureHold3717 N Ravenswood Avenue, Suite 243Chicago, IL 60613*****************Telephone + 773-472-8592; Toll Free 800-881-4495Fax + 773-525-1750Emergency telephone800-881-4495children. Irritating to eyes, respiratory system and skin.Hazardous IngredientsConc. CAS EINECS Symbols/Risk phrasesEthyl-2-cyanoacrylate(Ethyl cyanoacrylate)80 – 90% 7085-85-0 230-391-5 Xi;R36/37/381,4-Dihydroxybenzene (Hydroquinone) 0 – 0.5% 123-31-9 204-617-8 Carc Cat 3; R40 Muta Cat 3; R68 Xn;R22 Xi; R41R43 N; R50or symptoms persist.Eye contact Rinse immediately with plenty of water for 15 minutes holding eyelids open. Seekmedical attention. See medical attention of irritation or symptoms persist.Inhalation Move the exposed person to fresh air. Seek medical attention if irritation or symptomspersist.Ingestion DO NOT INDUCE VOMITING. Seek medical attention. Seek medical attention ifFire hazards Burning produces irritating, toxic and obnoxious fumes. Vapor may travel considerabledistance to source of ignition and flash back.Protective equipment Wear suitable respiratory equipment when necessary.Keep personnel away from spill.Environmental precautionsDo not allow product to enter drains. Do not flush into surface water. Prevent furtherspillage if safe.Clean-up methods Absorb with inert, absorbent material. Sweep up. Transfer to suitable, labeledAvoid contact with eyes and skin. Ensure adequate ventilation of the working area. Do not breathe gas/fumes/vapor/spray. Do not eat, drink or smoke in areas where thisproduct is used or stored. Do not empty into drains. Open container carefully.StorageKeep container tightly closed and in a well-ventilated place. Keep in a cool, dry, well-ventilated area. Store in correctly labeled containers. Avoid contact with: oxidizing Ethyl-2-cyanoacrylate (Ethyl cyanoacrylate) WEL 8-hr limit ppm –WEL 15 min limit ppm: 0.3WEL 8-hr limit mg/m3: –WEL 15 min limit mg/m3: 1.51,4-Dihydroxybenzene (Hydroquinone) WEL 8-hr limit ppm: – WEL 15 min limit ppm: – WEL 8-hr limit mg/m3: - 0.5 WEL 15 min limit mg/m3: –Engineering measures Ensure adequate ventilation of the working area. Occupational exposure controlsKeep away from food, drink and animal feeding stuffs.Respiratory protectionDo not breathe gas/fumes/vapor/spray. In case of hypersensitivity of the respiratory tract (e.g. asthmatics and those who suffer from chronic bronchitis) it is unadvisable to work with this product. Wear suitable protective equipment. Suitable half mask respirator withfilter P2 (EN 143).Hand protection Butyl rubber gloves. Wash hands after handling the product. Eye protection Avoid contact with eyes. In case of splashing, wear: Safety glasses.Protective equipmentAdopt best Manual Handling considerations when handling, carrying and dispensing. Color Clear. Odor Characteristic. Boiling point >150°C Flash point >85°CViscosityCone & Plate – 100 – 200 mPa.sConditions to avoid Direct sunlight. Heat. Moisture. Alkalis.Materials to avoid Reacts violently with water. Strong bases. Amines. Oxidizing agents.Hazardous decomposition Burning produces irritating, toxic and obnoxious fumes. Hazardous decomposition and mucous membranes.Corrosivity Exposure above the recommended occupational exposure limit (OEL) may cause adverse health effect. Inhalation may cause coughing, tightness of the chest and irritation of the respiratory system.SensitizationMay cause sensitization by inhalation and skin contact. Repeated or prolonged exposureMay cause allergic reactions in susceptible people. Mutagenic effects No mutagenic effects reported. Carcinogenic effects No carcinogenic effects reported. Reproductive toxicityNo teratogenic effects reported.Mobility No data is available on this product. Degradability More than 90% biodegradable. BioaccumulationNo data is available on this product.enter drains. Do not empty into drains.Disposal methods Dispose of in compliance with all local and national regulations.Disposal of packagingEmpty containers can be sent to landfill after cleaning, if in compliance with local and national regulations. Once the product residues adhering to the wall of the containers have been rendered harmless, the product and hazard labels must be invalidated.ADR/RIDUN 3334 Packaging Group -Class9Hazard ID -Proper ShippingNameAVIATION REGULATED LIQUID, N.O.S.IMGD (Vessel)UN 3334 Packaging Group - Class 9 Marine pollutant NOEmS Code -IATA (Air)UN 3334 Packaging Group - Class 9Subsidiary risk -Packing Instruction (Cargo)906Maximum quantity 220 L Packing Instruction (Passenger)906Maximum quantity 100 LFurther information This product is not classified as dangerous for carriage.15. REGULATORY INFORMATIONXi – IrritantRisk phrases R36/37/38 – Irritating to eyes, respiratory system and skin. Safety phrases S2 – Keep out of the reach of children. S22 – Do not breathe dust.S23 – Do not breathe gas/fumes/vapor/spray. S24/25 – Avoid contact with skin and eyes.S26 – In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.S51 – Use only in well-ventilated areas.P3 – Cyanoacrylate. Danger. Bonds skin and eyes in seconds. Keep out of the reach Section 3. R36/37/38 – Irritating to eyes, respiratory system and skin. R40 – Limited evidence of a carcinogenic effect. R50 – Very toxic to aquatic organisms.R68 – Possible risk of irreversible effects.Further informationThe information supplied in this Safety Data Sheet is designed only as guidance for the safe use, storage and handling of the product. This information is correct to the best of our knowledge and belief at the date of publication; however, no guarantee is made to itaccuracy. This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process.。
胶粘剂的使用方法
产品技术资料 IC M –RF08
胶粘剂的用途
1. 将多种未硫化氟弹性与多种基材通过热硫化粘合，也
可粘接同种已硫化氟橡胶。
基材有：碳钢、不锈钢、铜和铝等金属。
2. 适用不同的后硫化工艺。
同时也可粘接硅胶与塑料的粘接。
3. 适应多种氟橡胶配方。
特性
单组分、单涂型，工艺简便。
有优良的耐环境性能，如耐多种油脂,化学品，耐盐雾 可稀释至100～1000%
化学特性
典型值
外观 无色至淡黄 粘度TYP 3 含固量： 7.8-9.6% 比重： 0.835-0.90 闪 点： 16℃ 稀释剂： 甲醇或乙醇 溶 剂： 乙醇
稀釋比例:
1:3～8的无水乙醇（工业用含量95%以上的酒精）
使用说明
1.表面处理：机械处理(喷砂)后脱脂，或化学处理。
2.稀释：可不经稀释直接涂胶.若实际需要,亦可用前述稀释剂进行适量稀释.
2.涂 胶：用浸渍法、滚涂法、刷涂法或喷涂法将本胶水均匀涂覆于基材表面。
3.干 燥：室温干燥至少30分钟-60分钟,或高温150度下干燥5-15分钟.
4.停 放：按需要可在干燥后立即硫化,无需预烘.
使用注意事项
一段硫化: 推荐硫化温度为150℃-180℃.时间因胶粘剂不同而异进行调整.
二段硫化: 起始温度比一段硫化温度低10℃,由此逐步升温, 经过至少2-3小时至所需的最高温度,最高二段硫
化温一般不宜超过220℃
注意事项
远离儿童存放。
若不慎接触皮肤，擦拭干净，然后用清水冲洗；若不慎接触眼睛，立即用清水冲洗并到医院检查。
贮存条件
在8-28℃阴凉干燥处贮存。
贮存期为12个月。
胶粘剂使用说明书
环氧AB胶使用说明书
一、产品简介
本胶水为以环氧树脂为基础树脂的AB胶，可在室温下快速固化，适用于太阳能行业晶体硅棒切割过程中的粘接固定。
使用方法简单，粘度适中，易于操作，AB组分为不同颜色，易于辨别是否混合均匀；固化过程中固化收缩率小；固化后产品具有优异的粘接性能。
1、A剂和B剂按1：1重量称取后，务必充分搅拌混合均匀；如混合不均匀会
造成固化不充分，影响产品性能；
2、A剂和B剂混合后，开始反应，务必在操作时间之内完成涂胶操作，以免胶
水固化，影响使用；
3、B剂在储存过程中可能会出现结皮现象，使用之前小心将表面结皮去除即可
使用，注意不要将结皮固体残留到剩余的B剂中，以免有固体颗粒影响产品性能；
4、产品储存过程中可能有沉降现象，使用之前，请沿底部充分搅拌混合；
5、每次称取所需量后，请将产品包装罐密封，以免长期与空气接触影响产品性
能；
6、建议使用时戴防护手套，以免产品沾到皮肤或眼睛，沾到皮肤时请及时用清
洗剂洗净；如不慎沾到眼睛时，请先以水冲洗，再送医治疗。
六、储存与包装
1、包装规格为A剂1Kg/罐，B剂1Kg/罐；
2、本品需在通风、阴凉、干燥处密封保存。
3M Novec 电子级保护胶水说明书
Performance meets peace of mind.3M™ Novec™ Electronic Grade Coatings3M Science. Applied to Life.™3M™Novec™Electronic Grade CoatingsNo worries — inside or outside.Safe, sustainable electronic grade coatings help protect your device components from corrosion or your display surfaces from dirt,grime and fingerprintsElectronic devices have become an inescapable part of lifefor people around the world. From consumer devices like smartphones, tablets and wearables to specialized industrial technology such as automation controls, electronics and sensors are everywhere — including in many challenging environments. New industries, markets and geographies mean new demands for reliability and performance. This fuels the critical need to protect devices from environmental threats, including moisture, sulfur and pollution.Give your customers peace of mind with 3M™Novec™Electronic Grade Coatings. These ultra-thin coatings are designed to maintain optimal performance and functionality in a widerange of electronics applications. They help protect against environmental elements such as pollution and humidity that can cause corrosion and electrical failure, as well as contaminants such as oils, dirt, or grime that can affect the appearance and use of the device. Using 3M Novec coatings can help improve reliability and your customer’s user experience.What’s more, these coatings are engineered to be easy to work with because they dry quickly, can be applied using a varietyof application methods and most don’t have to be cured. Their low viscosity helps them form a thin protective layer on many materials used in electronics. That makes them a win-win solution — enhanced protection for your customers, and improved manufacturing efficiency for you. The science behind the solutions All Novec coatings are engineered for safetyand sustainability, utilizing unique proprietary3M chemistry. They are part of our longstanding commitment to continually improve the environmental, health and safety profiles ofour chemical products. All Novec coatings are formulated using 3M™Novec™Engineered Fluids, which are:• L ow global warming potential (GWP)solvents with zero ozone depletionpotential (ODP)• E xempt from the U.S. EPA definitions for Volatile Organic Compounds (VOCs)• N ot scheduled for regulatory phasedownor phase-out• L ow in toxicity with a wide marginof worker safety• Non-flammableWe have you covered.When you choose Novec coatings, you gain all the advantages of 3M’s innovative materials, chemical expertise and dedicated support. Here’s a look at some of the key benefits these high-performance coatings can help you realize:Engineered for:To give you:Protection A uniform oleophobic and hydrophobic layer that helps cover surfaces of a component for exceptional repellency of moisture, oils, dirt, grime, fingerprints and other environmental contaminantsSustainability Low environmental impact, zero ODP carrier solvents with low GWP , compared to conventional coatings formulated with hydrocarbon solventsSpeed Ability to handle coated components within seconds; many options do not need to be cured and masking components may not be requiredviscosity and surface tension make them easy to apply using a variety of methods.* They are ultra-thin and transparent so they have little to no impact on device performance and appearance.Easy-clean device surface protection Hand-held mobile devices and touchscreens let users access information with a simple swipe, but they also tend to accumulate fingerprints, oils, liquids, cosmetics and other materials that can damage them or make them unappealing to use. Choose durableNovec coatings for easy-clean device protection.• H elp keep surfaces smudge-free • H elp improve lubricity • D o not change surface appearance • E asy to apply — dries in seconds, thermal curing adds chemical and abrasion resistance • S uitable for protecting glass and glass-like surfaces Better together!Consider choosing sustainable 3M ™ Novec ™ Engineered Fluids as solvents for cleaning components prior to coating. They are also ideal carriers for coatings that need to be diluted before use. Ask your 3M representative for help determining which Novec fluid is right for your application. * Novec coatings can be applied using spray, dip or syringe methods.For spray application, 3M recommends using engineered controls or personal protection equipment (PPE) to help minimize worker exposure.Safety Data Sheet: Consult the safety data sheet before use.Regulatory: For regulatory information about this product, contact your 3M representative.Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed.Product Use: Many factors beyond 3M’s control and uniquely within user’s control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application.Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OR TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. The 3M ™ Novec ™ Brand Family The Novec brand is the hallmark for a variety of proprietary 3M products. Although each has its own unique formula and performance properties, all Novec products are designed in common to address the need for smart, safe and sustainable solutions in industry-specific applications. These include precision and electronics cleaning, heat transfer, fire protection, protective coatings, immersion cooling, advanced insulation media replacement solutions and several specialty chemical applications.Please recycle. Printed in USA. ©3M 2017. All rights reserved. Issued: 5/17 60-5002-0512-9 HB12118Electronics Materials Solutions Division 3M Center, Building 224-3N-11St. Paul, MN 55144-1000 USA /novec 1-800-810-85133M ™ N ovec ™ E ngineered Fluids 3M ™ N ovec ™ A erosol Cleaners 3M ™ N ovec ™ 1230 Fire Protection Fluid 3M ™ N ovec ™ E lectronic Grade Coatings 3M ™ N ovec ™ E lectronic Surfactants 3M ™ N ovec ™ D ielectric Fluids 3M and Novec are trademarks of 3M Company. Used under license by 3M subsidiaries and affiliates. 3M ™ Novec ™ Electronic Grade CoatingsEngineered for performance, safety and sustainability3M has been providing coatings to the electronics industry for decades, with our chemistries continually evolving and improving. Our scientists are constantly seeking the answers to how to do it all better, safer and more responsibly. The result — a broad range of ultra-thin 3M ™ Novec ™ Electronic Grade Coatings to choose from.With excellent repellency and corrosion protection, Novec coatings give you all the performance, without compromising safety and sustainability. Let’s get started—together3M Novec is more than a line of products – we’re people who share your passion for solving problems and improving lives.Not sure which coating is right for your application? We are here to help!Contact us to answer any questions you may have and for guidance, product data and test samples.Visit /Novec or contact your local 3M Novec representative for more information and to get started today.。
胶粘剂的配制及使用方法
胶粘剂的配制及使用方法1、胶粘剂的配制表面处理之后，就要进行调胶配胶。
对于单组分胶粘剂，一般是可以直接使用的，但是一些相容性差、填料多、存放时间长的胶粘剂会沉淀或分层，在使用之前必须要混合均匀。
若是溶剂型胶粘剂因溶剂挥发而导致浓度变大，还得用适当的溶剂稀释。
对于双组分或多组分胶粘剂，必须在使用前按规定的比例严格称取。
因为固化剂（交联剂）用量不够，则胶层固化不完全；固化剂用量太大，又会使胶层的综合性能变差。
因此，一般称取各组分时，相对误差最好不要超过2%～5%，以保证较好的粘接性能。
每次配胶量的多少，根据不同胶的适用期、季节、环境温度、施工条件和实际用量大小决定，做到随用随配，尤其是室温快速固化胶粘剂，一次配制量过多，放热量大，容易过早凝胶，影响涂胶，也会造成浪费。
有的胶粘剂配方中，固化剂或促进剂用量给出了很大范围。
一般地说，在夏天气温高时选用含量小的配方，其他情况下选用含量高的配方。
由于胶粘剂固化时要放热，因此，对于一些在常温下反应缓慢的胶粘剂，可以一次配足所需要的使用量，而对于一些室温下反应快或固化反应放热量大的胶粘剂，则应该少配、勤配，否则会由于配好的胶液因反应放出的热来不及散发而使胶液温度升高，进一步加快反应速度，结果使胶液在短时间内凝胶，甚至“暴聚”。
调胶时各组分搅拌均匀非常重要。
例如双组分环氧胶，若是固化剂分散不均匀，就会严重损害粘接性能，不是固化不完全，就是局部发粘发泡。
称取时还应当注意，取各组分的工具不能混用，调胶的工具也不能接触盛胶容器中未用的各组分，以防失效变质。
配胶的容器和工具最好在购胶时配套购置。
若买不到配套器具时，可选用玻璃、陶瓷、金属的干净容器，搅拌工具可用玻璃棒、金属棒代替。
但应当注意，这些器具中不能有油污、水或其他污染物，使用前最好用溶剂清洗干净。
配胶的场所宜明亮干燥、灰尘尽量少，对有毒性的胶，应在通风的环境中配制。
配胶原则上应由专人负责，应有适当的技术监督，从而保证获得优质的胶粘剂。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
FN-303S胶粘剂使用说明书
1、使用前将胶液仔细搅拌均匀，尤其是底部的配合剂（长期放置
后有少量配合剂沉淀物）要搅起来；
2、用棉布清除较部位表面灰尘，如有油污，可用棉布蘸汽油清洗，
使涂胶表面干燥清洁；如将欲粘合物表面磨糙，效果会更好。
3、在欲粘物上均匀的喷涂一薄层，晾至以手轻触近乎不粘时（晾
干时间随环境温度而变化），将两粘合面粘在一起，在用适当的
方法加压（≥20N/cm2），24小时后即可检验粘结情况。
注意事项：
4、以上使用方法，在常温干燥的情况下粘结效果更佳，当空气湿
度大于70%或者环境温度较低时，涂胶后晾置时间应适当延长，以手触近乎不粘为准。
5、当由于环境温度过低影响粘结效果时，可用热吹风机将脱胶部
位加热至50~60℃，使胶层变软后重新进行粘结即可。
6、不同用户的粘结条件、粘接材料各不相同，可探索使用最适合
的施工方法。
7、建议施工温度不低于10℃，低温状态时会影响粘结强度。