斯坦福发电机报价

合集下载

斯坦福发电机SX460型AVR说明书

斯坦福发电机SX460型AVR说明书

斯坦福发电机SX460型AVR说明书SX460 AUTOMATIC VOLTAGEREGULATOR (AVR)SPECIFICATION, INSTALLATION AND ADJUSTMENTS General description Technical specificationSX460 is a half-wave phase-controlled thyristor type Automatic Voltage Regulator (AVR) and forms part of the excitation system for a brush-less generator.In addition to regulating the generator voltage, the AVR circuitry includes under-speed and sensing loss protection features. Excitation power is derived directly from the generator terminals.Positive voltage build up from residual levels is ensured by the use of efficient semiconductors in the power circuitry of the AVR.The AVR is linked with the main stator windings and the exciter field windings to provide closed loop control of the output voltage with load regulation of +/- 1.5%.In addition to being powered from the main stator, the AVR also derives a sample voltage from the output windings for voltage control purposes. In response to this sample voltage, the AVR controls the power fed to the exciter field, and hence the main field, to maintain the machine output voltage within the specified limits, compensating for load, speed, temperature and power factor of the generator.A frequency measuring circuit continually monitors the generator output and provides output under-speed protection of the excitation system, by reducing the output voltage proportionally with speed below a pre-settable threshold. A manual adjustment is provided for factory setting of the under frequency roll off point, (UFRO). This can easily be changed to 50 or 60 Hz in the field by push-on link selection.Provision is made for the connection of a remote voltage trimmer, allowing the user fine control of the generator's output. INPUTVoltage Jumper selectable95-132V ac or190-264VacFrequency 50-60 Hz nominalPhase 1OUTPUTVoltage max 90V dc at 207V ac inputCurrent continuous 4 A dcIntermittent 6 A for 10 secsResistance 15 ohms minimumREGULATION+/- 1.5% (see note 1)THERMAL DRIFT0.05% per deg. C change in AVR ambient (note 2)TYPICAL SYSTEM RESPONSEAVR response 20 msFiled current to 90% 80 msMachine Volts to 97% 300 msEXTERNAL VOLTAGE ADJUSTMENT+/-10% with 1 k ohm 1 watt trimmer (see note 3)UNDER FREQUENCY PROTECTIONSet point 95% Hz (see note 4)Slope 170% down to 30 HzUNIT POWER DISSIPATION10 watts maximumBUILD UP VOLTAGE4 Volts @ AVR terminalsENVIRONMENTALVibration 20-100Hz 50mm/sec100Hz – 2kHz 3.3gOperating temperature -40 to +70°CRelative Humidity 0-70°C95% (see note 5)Storage temperature -55 to +80°CNOTES1. With 4% engine governing2. After 10 minutes.3. Applies to Mod status F onwards. Generator de-rate mayapply. Check with factory.4. Factory set, semi-sealed, jumper selectable5. Noncondensing.DESIGN DETAIL The main functions of the AVR are:Potential Divider and Rectifier takes a proportion of the generator output voltage and attenuates it. This input chain of resistors includes the range potentiometer and hand trimmer which adjust the generator voltage. A rectifier converts the a.c. into d.c. for further processing.The Amplifier (Amp) compares the sensing voltage to the Reference Voltage and amplifies the difference (error) to provide a controlling signal for the power devices. The Ramp Generator and Level Detector and Driver infinitely control the conduction period of the Power Control Devices and hence provides the excitation system with the required power to maintain the generator voltage within specified limits.The Stability Circuit provides adjustable negative ac feedback to ensure good steady state and transient performance of the control system.The Low Hz Detector measures the period of each electrical cycle and causes the reference voltage to be reduced approximately linearly with speed below a presettable threshold. A Light Emitting Diode gives indication of underspeed running.The Synchronising circuit is used to keep the Ramp Generator and Low Hz Detector locked to the generator waveform period.The Low Pass Filter prevents distorted waveforms affecting the operation of the AVR.Power Control Devices vary the amount of exciter field current in response to the error signal produced by the Amplifier. Suppression components are included to prevent sub cycle voltage spikes damaging the AVR components and also to reduce the amount of conducted noise on the generator terminals.The Power Supply provides the required voltages for the AVR circuitry.SUMMARY OF AVR CONTROLSCONTROL FUNCTION DIRECTIONVOLTS TO ADJUST GENERATOR OUTPUT VOLTAGE CLOCKWISE INCREASES OUTPUT VOLTAGE STABILITY TO PREVENT VOLTAGE HUNTING CLOCKWISE INCREASE THE DAMPING EFFECTUFRO TO SET THE UFRO KNEE POINT CLOCKWISE REDUCES THE KNEE POINTFREQUENCYADJUSTMENT OF AVR CONTROLSVOLTAGE ADJUSTMENTThe generator output voltage is set at the factory, but can be altered by careful adjustment of the VOLTS control on the AVR board, or by the external hand trimmer if fitted. Terminals 1 and 2 on the AVR will be fitted with a shorting link if no hand trimmer is required. Terminals L and L are linked only for special low voltage applications.CAUTION Do not increase the voltage above the rated generator voltage. If in doubt, refer to the rating plate mounted on the generator case.CAUTION Do not ground any of the hand trimmer terminals as these could be above earth potential. Failure to observe this could cause equipment damage.If a replacement AVR has been fitted or re-setting of the VOLTS adjustment is required, proceed as follows: CAUTION1. Before running generator, turn the VOLTS control fully anti-clockwise.2. Turn remote volts trimmer (if fitted) to midway position.3. Turn STABILITY control to midway position.4. Connect a suitable voltmeter (0-300V ac) across line to neutral of the generator.5. Start generator set, and run on no load at nominal frequency e.g. 50-53Hz or 60-63Hz.6. If the red Light Emitting Diode (LED) is illuminated, refer to the Under Frequency Roll Off (UFRO) adjustment.7. Carefully turn VOLTS control clockwise until rated voltage is reached.8. If instability is present at rated voltage, refer to stability adjustment, then re-adjust voltage if necessary.9. Voltage adjustment is now completed.TD_SX460.GB_05.03_02PO Box 17 ? Barnack Road ? Stamford ? Lincolnshire ? PE9 2NBTel: 00 44 (0)1780 484000 ? Fax: 00 44 (0)1780 484100Website: /doc/eb97771a4431b90d6c85c79c.html2003 Newage International Limited.Reprinted with permission of N.I. only. Printed in England.STABILITY ADJUSTMENTThe AVR includes a stability or damping circuit to provide good steady state and transient performance of the generator. The correct setting can be found by running the generator at no load and slowly turning the stability control anti-clockwise until the generator voltage starts to become unstable.The optimum or critically damped position is slightly clockwise from this point (i.e. where the machine volts are stable butclose to the unstable region).UNDER FREQUENCY ROLL OFF (UFRO) ADJUSTMENTThe AVR incorporates an underspeed protection circuit which gives a volts/Hz characteristic when the generator speed falls below a presettable threshold known as the "knee" point.The red Light Emitting Diode (LED) gives indication that the UFRO circuit is operating.The UFRO adjustment is preset and sealed and only requires the selection of 50 / 60Hz using the jumper link.For optimum setting, the LED should illuminate as the frequency falls just below nominal, i.e. 47Hz on a 50Hz system or57Hz on a 60Hz system.。

400KW CUMMINS 主发发电机组技术规格书

400KW CUMMINS 主发发电机组技术规格书

SPECIFICATION技术规格书Project:项目:Model:型号:KH-CCFJ400JWQty.:数量:1 SET/VESSELHull No.:船体号:Classification: 船级社: CCSFlag: 挂旗:Ship’s Owner: 船东: Deputy: 代表:Shipyard: 采购方: Deputy: 代表:Designer: 设计方: Deputy: 代表:Supply: 供货方:Deputy: 代表:Section A Technical Specification for Marine GensetA部分船用发电机组的技术规格Classification:船级社CCSAt Following Condition: 机组使用条件:In accordance with ISO 3046 reference conditions. 依据 ISO3046 标准Air Intake Temperature进气温度︒C 45Sea Water Temperature海水温度︒C 32Barometer Pressure大气压kPa 100Relative Humidity相对湿度% 60Transversal Inclination横倾22.5°Longitudinal Inclination纵倾10°Transversal Sway横摇22.5°Longitudinal Sway纵摇10°Genset can be normally operated under wet air,salt fog,oil fog and mildew fog, vibration and dash of condition. 可在潮湿空气、盐雾、霉菌的环境及正常营运所产生的振动和冲击下正常工作。

Power Deration: Operation at elevated temperature for sustained operating above 45 ℃,derate 2% per 11℃。

发电机配置表

发电机配置表

柴油发电机配置表技术规范(1)机组:常用功率(KW):400备用功率(KW):440频率:50Hz输出电压:400/230V转速:1500rpm功率因数:COSΦ=0.8(滞后)机组燃油耗(g/Kw*h):203.8最大输出电流(A):720相数/线数:三相四线(2)柴油机:型号:KTA19-G4冷却启动:闭式水冷却启动方式:24V直流电启动进气方式:涡轮增压中冷汽缸数:6汽缸总排量:18.9L供油方式:直喷汽缸排列方式:直列中冷方式:水空中冷燃油型号:国产0#轻柴油调速方式:电子调速压缩比:13.9:1缸径/行程:159/159mm机油容量(L):50冷却液容量(L):96K19系列发动机产品性能特点:•超强动力功率覆盖450-890马力,最大扭矩2586牛顿米。

自重1838公斤,功率自重比大•油耗低经济性好康明斯专利技术的PT燃油系统,超高喷射压力,保证发动机雾化良好,燃烧充分。

高效的Holset废气涡轮增压器可保证进气更充分,提高发动机效率,进一步改善燃烧,降低发动机比油耗。

空空中冷技术保证进气更充分,燃油经济性更好。

•结构紧凑、维护方便可更换湿式气缸套,散热效果好,更换容易。

所有机型零部件通用性强、系列化程度高,维修方便。

缸体和缸盖均采取内置式压力润滑油道,结构紧凑,故障率低。

•设计先进性能可靠缸体:高强度合金铸铁制造,刚性好、振动小、噪声低。

缸盖:每缸四气门设计、优化空气/燃油混合比,有效改善燃烧和排放;每缸一盖,维修方便。

凸轮轴:单凸轮轴设计可精确控制气门和喷油正时,优化的凸轮型线可减小冲击力,提高可靠性和耐久性。

曲轴:高强度锻钢制造的整体式曲轴,圆角及轴颈的感应淬火工艺可保证曲轴疲劳强度更高。

活塞:采用最新铝合金铸造技术,ω型头部和桶型裙部设计能补偿热胀冷缩,确保良好配合。

•专业配置最佳品质润滑系统:所有运动部件均为强制润滑;大容量齿轮泵提供压力润滑油对轴承进行润滑并冷却活塞;机油冷却器、全流式滤清器、旁通滤清器维持良好机油状态。

世界最大的电机

世界最大的电机

世界最大的电机电是人类最重要的能源之人,世界各地都需要用到电,那么关于世界上最大的电机你又了解过多少?下面店铺将为你介绍相关的资料。

发电机世界十大之最一、美国卡特彼勒发电机CATERPILLAR(卡特彼勒)公司是世界上最大的工程机械和建筑机械的生产商,也是全球高品质柴油发电机组和天然气发电机组的首席供应商。

CAT发动机的生产力和耐用性经久考验,CAT的品质已经被世界公认为第一,连续多年被美国《财富》杂志评为工业及农业设备制造行业排名第一。

卡特彼勒公司自1931年起设计及生产发动机,于1939年开始推出发电机组,累积了超过70多年的设计和生产经验。

多年来,卡特彼勒在设备的设计、开发研究上,投入了大量的人力、物力,使得CAT 产品在质量和性能上不断跃升。

美国卡特彼勒柴油发电机组是行业内唯一从发动机、发电机、控制系统及所有部件均由卡特彼勒公司一家厂家统一设计、制造、测试及保用,是目前全球最优质的发电机产品。

二、德国奔驰MTU发电机MTU公司是戴姆勒--奔驰公司的柴油机推进系统分部,世界上顶尖的重载柴油机制造公司。

其产品广泛用于军用车辆、铁道车辆、海上舰艇及长行电站。

MTU公司的前身早于1883年便开发了第一台高速车用内燃机。

1901年设计、制造了世界著名的梅塞德斯汽车。

自1909年起由制造飞机发动机转为生产重载柴油机。

1923年开始生产高性能的柴油机。

现在MTU公司的主要产品为重载柴油机(单机功率35至7400KW),燃气涡轮发动机,发动机电子管理系统及电子监控系统和重载变速箱。

1997年初,MTU公司向市场推出最佳产品:2000系列及4000系列发动机。

三、英国珀金斯发电机1932年的Perkins珀金斯公司是世界最早生产发动机公司的公司之一。

所生产的以柴油和天然气作为燃料的发动机因其经济性,可靠性和耐久性的优点在各行业当中得到广泛的推广和应用。

如汽车、工程机械、农业机械、工业用发电机组及船舶等。

产品方面有100、3.152、4.236、1000、1300、2000、3000和4000系列。

无动柴油发电机组技术参数

无动柴油发电机组技术参数

无动柴油发电机组技术参数:机组型号 :300KW ;柴油机品牌:无锡动力;柴油机型号:WD258TD30;汽缸数:6;常用功率:309KW;备用功率:340KW额定燃油耗(g/KW.h) :213;缸径*行程(mm) :135*150冷却方式:闭式水箱冷却;发电机厂家:上海斯坦福电机型号:无刷自励磁;电压(V) : 400/230V额定电流(A) :540;频率(HZ) :50转速(r/min) :1500;相数:三相四线;功率因素:0.8滞后;重量(kg) : 3300;尺寸(mm) :3000*1500*1800发电机基本配置:1.发动机部分:柴油滤清器、空气滤清器、机油滤清器、自充电系统2.发电机部分:空气开关、机组控制屏3.水箱散热器4.钢制底座5.减振垫6.附件部分:消声器、蓄电池、电池线、备件箱。

7.技术文件:柴油机及发电机原厂技术文件、发电机组说明书、测试报告等质保期:国内,一年或运行1000小时(先到为准),由于产品质量问题实行免费维修或换件,终身有偿服务(易损件、常用件、人为损坏、疏忽保养等均不在保修范围内)。

本厂是专业生产15KW—2000KW国产、进口柴油发电机组专业制造企业,严格按GB/T2820-1997标准组织生产。

主要产品有:半自动、全自动、低噪音、二轮、四轮移动式柴油发电机组,规格从15—2000KW 70余种。

另制作组装进口康明斯、沃尔沃、奔驰柴油发电机组、配西门子、马拉松、斯坦福发电机,可作为宾馆、工矿、农村、山区、野外作业、企事业、机关、学校或专业户的动力和照明之用。

本厂坚持优质华昌品牌,优良服务赢天下顾客,以优质的产品,周到的服务,与新老顾客共创新高。

华中宏泰上柴发电机组全部选用正宗上柴股份有限公司生产的发动机配套无刷全铜发电机组装而成,每台发电机组都可以短时间超载10%使用.本公司郑重承诺,每台上柴发电机组出厂前都经过公怀的严格检测,保证质量,全国联保。

斯坦福发电机介绍

斯坦福发电机介绍

斯坦福发电机简介康明斯发电机技术(中国)有限公司(原无锡新时代交流发电机有限公司)是康明斯发电机技术系统在中国的唯一的独资企业,首期投资1760万美元。

成立于1996年2月,于1997年11月正式开业。

目前年生产能力为65,000台发电机。

康明斯发电机技术系统有50多年成功地满足顾客需要的经验,是世界交流发电机技术的先导,康明斯发电机技术系统拥有全球销售和服务网络,并在英国、美国、中国、印度有生产工厂。

无锡工厂完全按照康明斯发电机技术系统的设计及工艺标准来制造斯坦福交流发电机。

产品设计、材料、生产、试验均由英方人员直接管理控制。

体积小,重量轻,技术先进,性能可靠是斯坦福发电机的重要特性。

康明斯发电机技术系统制造的斯坦福发电机可与世界上所有柴油机配套,如康明斯、帕金斯、VOLVO、MTU、道依茨、卡特彼勒和国产95、130、135、150、190系列等柴油机。

各系列产品成功供应发电机组成套厂家,广泛应用于铁路、船舶、邮电通信、军工、油田、交通、高层建筑及冷藏集装箱等领域。

康明斯发电机技术系统所生产的发电机系列为:BC16、BC18、UC224、UC274、HC4、HC5、LV6、HC7。

功率范围为:6.5KW -2000KW。

HC系列的发电机为无刷旋转磁场结构,电压最高达660V/50HZ或60HZ,满足BS5000标准第三部分和其他国际标准。

在HC4,HC5,HC6/LV6,HC7四个机座号中,200KW-2000 KW范围内,可选1500rpm(50HZ)或1800rpm(60HZ)、4极的发电机。

在HC6/LV6和HC7两个机座号中,224KW-1300KW范围内,可选1000rpm(50HZ)或1200rpm(60HZ)、6极的发电机。

机座号位HC4和HC5的发电机,其励磁系统可为使用AS440或SX421AVR的定子供电或为使用MX341或MX321AVR的永磁发电机(PMG)励磁,机座号位HC6/LV6和HC7的发电机使用MX341或MX321AVR的永磁发电机(PMG)励磁系统。

斯坦福STAMFORD发电机简介

斯坦福STAMFORD发电机简介

E ngineering 工 程
新时代公司总部/工 厂(斯 坦 福)
无锡新时代交流发电机有限公司

无锡新时代成立时间-- 1996年3月
所有权:
新时代国际有限公司 - 75% 江苏海星电机集团有限公司 - 25%
工厂开业时间 - 1997年6月


二零零二年七月,无锡新时代成为一家独资公司
世界上的新时代公司
辅助绕组励磁的AVR控制系统
旋转整流装置 励磁磁场 主定子 线圈 风扇 机座
N
轴承 N
S 励磁转子 S
轴伸
主转子(磁场)
电压感应 AVR 功率输入
电源引出线
稳态电压调整率 +/- 1%或±1.5%
永磁机励磁的AVR控制系统
主要特点 主要特点
N N
极小的调整率
并联运行 可装功率因数控制器
N S
负载减荷
无锡新时代交流发电机业务情况
百万人民币
700 600 500 400 300 200 100 0 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006
无锡新时代业务情况
台 45000
40000 35000 30000 25000 20000 15000 10000 5000 0 1997 1999 2001 2003 2005 West
斯坦福(Stamford) BC16 和 BC18

6.5kW 至 32kW (50Hz)
自励或永磁机励磁 AVR 有两种安装位置
斯坦福(Stamford) UC224 和 UC274
34kW 至 160kW (50Hz)
自励或永磁机励磁 AVR 有两种安装位置

sTF一500一4型斯坦福发电机组操作说明

sTF一500一4型斯坦福发电机组操作说明

sTF一500一4型斯坦福发电机组操作说明斯坦福发电机组是一种常用于机组作业的动力设备,它的操作步骤需要严格遵循操作手册和安全规范。

本文将详细介绍STF一500一4型斯坦福发电机组的操作说明。

一、前期准备1.确保操作人员已经接受过必要的安全培训,了解发电机组的相关知识和操作规程。

2.确保发电机组周围场地整洁,安全通畅,无杂物和障碍物。

3.检查发电机组的燃油、水和润滑油的储备情况,确保充足供应。

二、启动操作1.检查发电机组的电源开关,确认处于"关闭"位置。

2.打开燃油进气阀门,并检查燃油管道是否有渗漏。

3.打开液压油箱开关,检查液压油位是否正常。

5.当发电机组通过自检后,将会启动发动机。

此时应观察仪表板上的指示灯,确保发动机正常运转。

6.根据需求,调整发动机的转速,控制发电机的电压输出。

三、运行操作1.当发电机组正常运行时,应定期检查润滑油的油位,确保在合理范围内。

2.每隔一段时间,检查发电机组的冷却水的温度和压力,保持在正常范围内。

3.定期巡视发电机组设备,检查连接器、螺钉和紧固件是否松动,如有需要进行调整。

4.监视发电机组的运行状态,确保各项指标处于正常范围内。

5.在发电机组工作结束后,应先将负载卸除,然后降低发动机的转速,最后关闭发电机组。

四、安全措施1.不得擅自更换或维修发电机组的零部件,必须由专业人员进行操作。

2.在操作发电机组时,注意安全用电,避免触电等危险情况。

3.操作人员应佩戴安全帽、防护服等个人保护装备,并严格遵守现场安全规则。

4.发电机组周围严禁堆放易燃物品,保持通风良好。

5.发电机组停机后,应等待一段时间,确保设备冷却后再进行维护和检修。

以上是STF一500一4型斯坦福发电机组的操作说明,操作人员在使用过程中应严格按照操作手册和安全规范进行操作,确保发电机组的安全和正常运行。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

LVI634B LVI634C LVI634D LVI634E LVI634F LVI634G
711 758 862 944 1052 1146
600 640 728 800 904 1000
118727 124832 133641 146856 163013 168882
PI 734A PI 734B PI 734C PI 734D PI 734E PI 734F PI 734G
PI142J
24.2
36
15147
2015年1月1日起执行
加36000元
已下浮
4847.7 5228.6 6071.65 6503.25 6678.75 6934.85 7320.3 7577.05
8242 9146.15 9686.95 9965.15
已下浮
5138.25 5805.8 6506.5 6620.25 7140.9 7296.9 7577.7 8483.15 8787.35 9845.55
1500 rpm/50z
44
34
52
40
60
48
75
58
83
68
100
80
117
96
143
112
165
128
185
145.6
204
160
240
184
250
200
配套价(元) 直接
15736 17511 20464 21211 23403 27294 30309 32463 33350 35580 37773 42358 44315
型号
UCI 224C UCI 224D UCI 224E UCI 224F UCI 224G UCI 274C UCI 274D UCI 274E UCI 274F UCI 274G UCI 274H UCD 274J UCD 274K
STAMFORD斯坦福(英国独资)
容量 (KW)
1800 rpm/60z
8242 9146.15 9686.95 9965.15
STAMFORD斯坦福(英国独资)
型号
容量 (KW)3600转
单项60Hz
三项60Hz
配套价(元) 直 接
PI042D
7.5
11
7905
PI042E
9
13.3
8932
PI042F
10.3
15.2
10010
PI042G
12
17.6
10185
PI142D
24
19.04
28
21.8
32
22.8
34
配套价(元)
直接
7458 8044 9341 10005 10275 10669 11262 11657 12680 14071 14903 15331
STAMFORD斯坦福(英国独资)
型号
容量 (KW)3000转
单项50Hz
三项50Hz
配套价(元) 直接
PI042D
已下浮
10228.4 11382.15 13301.6 13787.15 15211.95 17741.1 19700.85 21100.95 21677.5
23127 24552.45 27532.7 28804.75
0 30728.75 33638.8 34835.45 35511.45 44102.5 44428.8 49019.75 51121.85 62988.9 69338.1 74290.45 97368.96 104239.98 114547.68 127150.14
13.6
20
10986
PI142E
16.9
24.8
11226
PI142F
19
28
11658
PI142G
21.8
32
13051
PI142H
25.6
37.6
13519
PI142J
27.2
40
14426
已下浮
5138.25 5805.8 6506.5 6620.25 7140.9 7296.9 7577.7 8483.15 8787.35 9376.9
10.8
15.4
12.6
17.6
15.7
22
17.2
24.2
18.8
26.4
21.9
30.8
25
元) 直

7458 8044 9341 10005 10275 10669 11262 11657 12680 14071 14903 15331
已下浮
4847.7 5228.6 6071.65 6503.25 6678.75 6934.85 7320.3 7577.05
型号
PI044D PI044E PI044F PI044G PI044H PI144D PI144E PI144F PI144G PI144H PI144J PI144K
容量 (KW)1500转
单项50Hz
三项50Hz
4
6
5.4
8
6.7
10
8.1
12
9.4
14
10.9
16
13.6
20
15
22
16.32
1220 1352 1512 1612 1840 2080 2200
1008 1120 1240 1320 1520 1664 1760
176228 181366 186515 205874 240840 267284 281963
IP44 防护等级HC4系以上另加36000元
IP44 防护等级HC4系以上另加36000元
6.72
10
7905
PI042E
8.08
12
8932
PI042F
9.36
14
10010
PI042G
10.72
16
10185
PI142D
13.44
20
10986
PI142E
14.72
22
11226
PI142F
17.12
25.5
11658
PI142G
20.1
30
13051
PI142H
21.44
32
13519
STAMFORD斯坦福(英国独资)
型号
PI044D PI044E PI044F PI044G PI044H PI144D PI144E PI144F PI144G PI144H PI144J PI144K
容量 (KW)1800转
单项60Hz
三项60Hz
4.6
6.6
6.2
8.8
7.7
11
9.3
13.2
HCI 444C HCI 444D HCI 444ES HCI 444E HCI 444FS HCI 444F HCI 544C HCI 544D HCI 544E HCI 544F-S HCI 544F HCI 634G HCI 634H HCI 634J HCI 634K
252 300 335 352 380 400 475 515 600 620 660 775 900 1000 1130
0 92607.06 97368.96 104239.98 114547.68 127150.14 131727.96
0 137457.84 141465.48 145481.7 160581.72 187855.2 208481.52 219931.14
加36000元
STAMFORD斯坦福(英国独资)
200 240 260 280 304 320 400 440 488 500 536 648 752 824 908
47275 51752 53593 54633 67850 68352 75415 78649 96906 106674 114293 124832 133641 146856 163013
相关文档
最新文档