杭州瑞诚 微孔板振荡器 TS200-中文简介
ZQWY-200 卧式恒温振荡培养箱 说明书
目录一、产品介绍和使用范围 (1)二、性能特点 (1)三、技术指标 (1)四、安装要求 (2)五、操作使用说明 (2)六、注意事项 (7)七、保修期 (7)一、产品介绍和使用范围ZQWY-200卧式恒温振荡培养箱，广泛的应用于微生物、病毒、细菌培养、发酵、杂交和生物化学反应以及细胞组织等研究。
为温度、振荡频率、振幅有不同要求的培养以及酶工程等方面的研究提供了有效的帮助。
在医学生物学、分子学、制药、食品、环保等研究领域有着广泛而重要的作用。
二、性能特点1、LCD大屏幕背光液晶显示，参数的设定、观察清晰直观；2、PID微电脑智能控温仪，控温精确；3、具有定时功能：0～999.9小时内任意设定培养时间；4、采用红外加热管，升温快，耗能少；5、激光测速装置，显示转速与实际转速完全一致，避免了传统的比例测算法出现的实际转速与显示转速之间的误差，转速更加精确可靠；6、三维一体的偏三轮驱动，运转平滑、稳定、耐久、可靠；7、静音风扇设计和强制对流方式，确保了良好的恒温效果；8、具有超温报警功能及异常情况自动断电功能；9、具有断电恢复功能，避免因停电、死机而造成的数据丢失问题；10、采用特种的交流感应无刷电机，使用后故障少、寿命长,免保养。
11、流线型外观，镜面不锈钢内衬，大屏幕玻璃视窗方便随时在不开门情况下观察箱体内部情况，,静电喷塑箱体。
三、技术指标品名恒温振荡培养箱型号ZQWY-200振荡频率40-300rpm振荡频率精度±1rpm摇板振幅Ф26mm温控范围4℃～60℃温度调节精度±0.1℃温度均匀度±1℃显示方式LCD（液晶显示屏）对流方式强制对流控制方式P．I．D微电脑智能控制最大容量单层250ml×54或500ml×40或1000ml×24定时范围0-999.9小时摇板尺寸850×520mm标准配置万能夹具电源AC220±10%50～60Hz外型尺寸（长×宽×高）1330×670×710mm重量170kg四、安装要求1、培养箱应放在平面坚实的台面上；2、安放地点无强烈光照、无强烈腐蚀性气体、相对湿度85%一下；3、室内通风良好，振荡器后背与墙面间距离应大于40公分；4、使用电源：交流220V±10%，50HZ,容量不小于1KW，备有地线的电源插座。
TDS3000C系列数字振荡器数据手册说明书
RM3000TDS3012CENCORE TDS3TMT TDS3VID TDS3012CENCOREDigital Phosphor OscilloscopesTDS3000C Series DatasheetThe TDS3000C Series provides you with the performance you need at a price you can afford. Bandwidths range from 100 MHz to 500 MHz, with up to 5 GS/s sample rates for accurate representation of your signal.Key performance specifications100 MHz, 300 MHz, and 500 MHz bandwidth models2 or 4 analog channel modelsSample rates up to 5 GS/s real time on all channels10k record length on all channels3,600 wfms/s continuous waveform capture rate Suite of advanced triggersKey featuresFront-panel USB host port for easy storage and transfer ofmeasurement data25 automatic measurementsFFT standardMultiple language user interfaceWaveAlert ®automatic waveform anomaly detectionTekProbe ® interface supports active, differential, and current probes for automatic scaling and unitsPortable designLightweight design (only 7 lb./3.2 kg) for easy transportOptional internal battery operation provides up to three hours without line powerApplication modules for specialized analysisAdvanced analysis moduleLimit testing moduleTelecommunications mask testing module Extended video moduleApplicationsDigital design and debugVideo installation and servicePower supply designEducation and trainingTelecommunications mask testingManufacturing test General bench testingDPOs provide greater level of insight into complex signalsThe TDS3000C Series offers fast waveform capture rates on a continuous basis that save you time by quickly revealing the nature of faults, so advanced triggers can be applied to isolate them.Real-time intensity grading highlights the details about the history of a signal's activity, making it easier to understand the characteristics of the waveforms you've captured. Unlike other comparable oscilloscopes, thehistory remains even after the acquisition has been stopped. 1Quickly debug and characterize signals with DRT sampling technology and sin (x)/x interpolationThe TDS3000C Series combines unique digital real-time (DRT) sampling technology with sin(x)/x interpolation to allow you to accurately characterize a wide range of signal types on all channels simultaneously. With the TDS3000C Series there is no change in sampling rate when additional channels are turned on, unlike other comparable oscilloscopes. This sampling technology makes it possible to capture high-frequency information, such as glitches and edge anomalies, that elude other oscilloscopes in its class, while sin(x)/x interpolation ensures precisereconstruction of each waveform.Look for unintentional circuit noise with the TDS3000C series’ FFT capability.Custom video triggering allows the TDS3000C Series to trigger on standards such asRS-343 (26.2 kHz scan rate).The TDS3000C Series provides breakthrough test speeds for telecommunications line card testing. The telecom QUICKMENU puts all the commonly used telecom test functions on a single menu.Easy to setup and useWhen working under tight deadlines, you need your oscilloscope to be intuitive; you want to minimize time spent learning and relearning how to use it. The TDS3000C Series oscilloscopes help reduce your learning curve. Simple navigation and dedicated front-panel controls get you to where you want to be quickly, so that you spend less time learning andmore time on the task at hand.The TDS3000C series with the TDS3LIM module is ideal for manufacturing test applications where fast Go/No-Go decisions are required.Datasheet2 WaveAlert waveform anomaly detection alerts you to any waveform that deviates fromthe “normal” input such as the glitch on channel 2.Easily transfer, document, and analyze data on your PC.Simple documentation and analysisThe TDS3000C Series comes equipped with a USB host port so you can easily store and transfer measurement information to your PC.OpenChoice ®PC Communication Software allows you to simply pull screen images and waveform data into a standalone desktop application or directly into Microsoft Word and Excel.If you prefer not to use a PC for analysis, the TDS3000C Series comes standard with 25 automatic measurements, waveform add, subtract, divide,and multiply math functions, and Fast Fourier Transform (FFT). Unlike other comparable oscilloscopes, the TDS3000C Series math andmeasurement allows you to use the full acquisition record length or isolate a specific occurrence within an acquisition.Instrument controlUtilizing the built-in ethernet port, e*Scope web-based remote control allows you to a control TDS3000C series oscilloscope from anywhere,using the internet and your PC.Work where you need toThe TDS3000C Series packs the power of a DPO in a compact design that is only 5.9 in. (149 mm) deep, freeing up valuable benchtop space. And when you need to move your oscilloscope to another lab, its portable 7 lb.(3.2 kg) design makes for easy transport.If your work demands even more mobility, then the optional battery packwill give you up to three hours of operation without line power.TDS3BATC provides you with up to three hours of portable battery operation.TDS3000C Series Digital Phosphor Oscilloscopes 3SpecificationsAll specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.Vertical systemHardware bandwidth limitsInput coupling AC, DC, GNDInput impedance 1 MΩ in parallel with 13 pF or 50 ΩInput sensitivity range1 MΩ 1 mV/div to 10 V/div 50 Ω 1 mV/div to 1 V/div Vertical resolution 9 bits Maximum input voltage1 MΩ150 V RMS with peaks at ≤400 V 50 Ω 5 V RMS with peaks at ≤30 V DC gain accuracy ±2%Position range±5 divHorizontal systemSeconds/division rangeTime base accuracy±20 ppm over any 1 ms time intervalDatasheet4 TDS3000C Series Digital Phosphor Oscilloscopes Trigger systemTrigger modes Auto (supports Roll Mode for 40 ms/div and slower), Normal, Single SequenceB trigger Trigger after time or eventsTrigger after time range13.2 ns to 50 sTrigger after events range 1 to 9,999,999 eventsTrigger typesEdge Conventional level-driven trigger. Positive or negative slope on any channel. Coupling selections: AC, DC, Noise Reject, HFReject, LF RejectVideo Trigger on all lines or individual lines, odd/even or all fields on NTSC, PAL, SECAMExtended video Trigger on specific lines in broadcast and non-broadcast (custom) standards and on analog HDTV formats (1080i, 1080p, 720p,480p). Requires TDS3VID application modulePulse width (or glitch)Trigger on a pulse width <, >, =, ≠ to a selectable time limit ranging from 39.6 ns to 50 sRunt Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first againRise/fall time Trigger on pulse edge rates that are either faster or slower than a set rate. Edges can be rising, falling, or eitherPattern Specifies AND, OR, NAND, NOR when true or false for a specific timeState Any logic state. Triggerable on rising or falling edge of a clock. Logic triggers can be used on combinations of 2 inputs (not 4) Comm Provides isolated pulse triggering required to perform DS1/DS3 telecommunications mask testing per ANSI T1.102 standard.Requires TDS3TMT application moduleAlternate Sequentially uses each active channel as a trigger sourceAcquisition systemDPO Captures and displays complex waveforms, random events and subtle patterns in actual signal behavior. DPOs provide3 dimensions of signal information in real time: Amplitude, time, and the distribution of amplitude over timeSample Sample data onlyAverage Waveform averaged, selectable from 2 to 512Envelope Min-max values acquired over one or more acquisitionsPeak detect High-frequency and random glitch capture. Captures glitches as narrow as 1 ns (typical) using acquisition hardware at all timebase settingsWaveAlert®Monitors the incoming signals on all channels and alerts the user to any waveform that deviates from the normal waveform beingacquiredSingle sequence Use the Single Sequence button to capture a single triggered acquisition sequence at a time 5DatasheetWaveform measurementsCursors Amplitude, timeAutomatic measurements Display any four measurements from any combination of waveforms. Or display all measurements with measurement snapshotfeature. Measurements include Period, Frequency, +Width, -Width, Rise time, Fall time, +Duty cycle, -Duty cycle, +Overshoot,High, Low, Max, Min, Peak-to-peak, Amplitude, Mean, Cycle mean, RMS, Cycle RMS, Burst width, Delay, Phase, Area 1, CycleArea 1Measurement statistics Mean, Min, Max, Standard deviation. Requires TDS3AAM application moduleThresholds User-definable thresholds for automatic measurements; settable in percent or voltageGating Isolate a specific occurrence within an acquisition to take measurements, using either the screen or cursorsWaveform mathArithmetic Add, subtract, multiply, and divide waveformsFFT Spectral magnitude. Set FFT vertical scale to Linear RMS or dBV RMS, and FFT window to Rectangular, Hamming, Hanning, orBlackman-HarrisAdvanced math Integrate, differentiate, define extensive algebraic expressions including analog waveforms, math functions, scalars, up to twouser-adjustable variables and results of parametric measurements. For example: (Intg (Ch1-Mean(Ch1)) × 1.414 × VAR1) 2Waveform processingAutoset Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo autosetDeskew Channel-to-channel deskew ±10 ns may be manually entered for better timing measurements and more accurate math waveformsDisplay systemDisplay type 6.5 in. (165.1 mm) liquid-crystal TFT color displayDisplay resolution640 horizontal × 480 vertical pixels (VGA)Interpolation Sin(x)/xWaveform styles Dots, vectors, variable persistence, infinite persistenceGraticules Full, grid, crosshair, and frame. NTSC, PAL, SECAM, and vectorscope (100% and 75% color bars) with optional TDS3VIDapplication moduleFormat YT, XY, and Gated XYZ (XY with Z-axis blanking available on 4-channel instruments only)1Requires TDS3AAM application module.2Requires TDS3AAM application module.6 Input/output portsEthernet port RJ-45 connector, supports 10Base-T LANUSB port Front-panel USB 2.0 host port. Supports USB flash driveGPIB port Full talk/listen modes, setting and measurements.(Optional with TDS3GV Communications Module)RS-232C port DB-9 male connector, full talk/listen modes; control of all modes, settings and measurementsBaud rates up to 38,400(Optional with TDS3GV Communications Module)VGA video DB-15 female connector, monitor output for direct display on large VGA-equipped monitors(Optional with TDS3GV communications module)External trigger input BNC connector, input impedance >1 MΩ in parallel with 17 pF; max input voltage is 150 V RMSPower sourceAC line powerSource voltage100 V RMS to 240 V RMS ±10%Source frequency45 Hz to 440 Hz from 100 V to 120 V45 Hz to 66 Hz from 120 V to 240 VPower consumption75 W maximumBattery power Requires TDS3BATC, rechargeable lithium ion battery packOperating time, typical 3 hoursPhysical characteristicsDimensionsWeightPackage dimensionsRackmount (RM3000)TDS3000C Series Digital Phosphor Oscilloscopes 7DatasheetEMC, environment and safetyTemperatureOperating0 ºC to +50 ºCNon-operating-40 ºC to +71 ºCHumidity(Operating and non-operating)At or below +30 ºC Up to 95% RH+30 ºC up to +50 ºC Up to 45% RHAltitudeOperating To 3,000 metersNon-operating15,000 metersElectromagnetic compatibility Meets or exceeds EN61326 Class A, Annex D radiated and conducted emissions and immunity; EN6100-3-2 AC PowerlineHarmonic Emissions; EN6100-3-3 Voltage Changes, Fluctuation, and Flicker; FCC 47 CFR, Part 15, Subpart B, Class A;Australian EMC frameworkSafety UL61010B-1, CSA1010.1, IEC61010-1, EN61010-1Ordering informationTDS3000C familyTDS3012C100 MHz, 2 channels, 1.25 GS/sTDS3014C100 MHz, 4 channels, 1.25 GS/sTDS3032C300 MHz, 2 channels, 2.5 GS/sTDS3034C300 MHz, 4 channels, 2.5 GS/sTDS3052C500 MHz, 2 channels, 5 GS/sTDS3054C500 MHz, 4 channels, 5 GS/sPlease specify a language option and a power plug option from the lists that follow.8 Standard accessoriesProbesP6139B500 MHz 10x passive probe, one per channel AccessoriesFront protective coverAccessory trayDocumentation CD Contains User Manuals in all languagesFront panel overlay Translated front panel overlay. Specify language option.Installation and Safety ManualPower cord Specify power plug option.OpenChoice® PC connectivity software Enables fast and easy communication between Windows PC and the TDS3000C Series through LAN, GPIB, or RS-232. Transfer and save settings, waveforms, measurements, and screen imagesTraceable Certificate of Calibration NIM/NISTWarrantyThree year warranty covering all labor and parts, excluding probes and accessoriesInstrument optionsPower plug optionsOpt. A0North America power plug (115 V, 60 Hz)Opt. A1Universal Euro power plug (220 V, 50 Hz)Opt. A2United Kingdom power plug (240 V, 50 Hz)Opt. A3Australia power plug (240 V, 50 Hz)Opt. A4North America power plug (240 V, 50 Hz)Opt. A5Switzerland power plug (220 V, 50 Hz)Opt. A6Japan power plug (100 V, 50/60 Hz)Opt. A10China power plug (50 Hz)Opt. A11India power plug (50 Hz)Opt. A12Brazil power plug (60 Hz)Opt. A99No power cordTDS3000C Series Digital Phosphor Oscilloscopes 9DatasheetLanguage optionsOpt. L0English manualOpt. L1French manualOpt. L2Italian manualOpt. L3German manualOpt. L4Spanish manualOpt. L5Japanese manualOpt. L6Portuguese manualOpt. L7Simplified Chinese manualOpt. L8Traditional Chinese manualOpt. L9Korean manualOpt. L10Russian manualOpt. L99No manualLanguage options include translated front-panel overlay for the selected language(s). Service optionsRecommended accessoriesProbesADA400A100x, 10x, 1x, 0.1x high-gain differential amplifier P5100A 2.5 kV, 100x high-voltage passive probeP5205A 1.3 kV, 100 MHz high-voltage differential probe P5210A 5.6 kV, 50 MHz high-voltage differential probe P6243 1 GHz, ≤1 pF input C 10x active probeTCP202A50 MHz, 15 A AC/DC current probeTCP30315 MHz, 150 A current probe 3TCP305A50 MHz, 50 A current probe 3TCP312A100 MHz, 30 A current probe 3TCPA300100 MHz probe amplifier3Requires TCPA300 probe amplifier.TCPA40050 MHz probe amplifierTCP404XL 2 MHz, 500 A current probe 4AccessoriesTDS3GV GPIB, VGA, RS-232 interfaceTDS3AAM Advanced Analysis Module. Adds extended math capability, arbitrary math expressions, measurement statistics, and additionalautomated measurementsTDS3LIM Limit Testing Module. Adds custom waveform limit testing capabilitiesTDS3TMT Telecom Mask Testing Module. Adds pass/fail compliance of ITU-T G.703 and ANSI T1.102 standards, custom mask testing, andmoreTDS3VID Extended Video Analysis Module. Adds video quickmenu, autoset, hold, line count trigger, video picture mode, vectorscope 5mode, HDTV format trigger graticules, and moreTDS3BATC Lithium-ion battery pack for up to 3 hours continuous operation without line powerTDS3ION Battery chargerAC3000Soft case for carrying instrumentHCTEK4321Hard plastic case for carrying instrument(requires AC3000)RM3000Rackmount kit071-2507-xxService manual (English only)Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.4Requires TCPA400 probe amplifier.5Vectorscope does not support composite video.TDS3000C Series Digital Phosphor OscilloscopesDatasheetASEAN / Australasia (65) 6356 3900 Austria 00800 2255 4835*Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777 Belgium 00800 2255 4835*Brazil +55 (11) 3759 7627 Canada180****9200Central East Europe and the Baltics +41 52 675 3777 Central Europe & Greece +41 52 675 3777 Denmark +45 80 88 1401Finland +41 52 675 3777 France 00800 2255 4835*Germany 00800 2255 4835*Hong Kong 400 820 5835 India 000 800 650 1835 Italy 00800 2255 4835*Japan 81 (3) 6714 3010 Luxembourg +41 52 675 3777 Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90Middle East, Asia, and North Africa +41 52 675 3777 The Netherlands 00800 2255 4835*Norway 800 16098People's Republic of China 400 820 5835 Poland +41 52 675 3777 Portugal 80 08 12370Republic of Korea +822 6917 5084, 822 6917 5080 Russia & CIS +7 (495) 6647564 South Africa +41 52 675 3777Spain 00800 2255 4835*Sweden 00800 2255 4835*Switzerland 00800 2255 4835*Taiwan 886 (2) 2656 6688 United Kingdom & Ireland 00800 2255 4835*USA180****9200* European toll-free number. If not accessible, call: +41 52 675 3777For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit . Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification andprice change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.26 Aug 2016 41W-12482-25 TDS3VID TDS3012C TDS3032C TDS3034C TDS3052C TDS3054C TDS3014C TDS3BATC TDS3GV TDS3TMTRM3000TDS3012CENCORE TDS3TMT TDS3VID TDS3012CENCORE。
微孔板恒温振荡器 中文简介
（可用于深孔板培养）
1．产品简介与特点
TS300微孔板专用恒温振荡器是一款由直流无刷电机和PID智能控温技术相结合的多用途恒温振荡器。
其PID模糊控制技术能够精准的确保控温精度，并自动调整加热速率节省等待时间。
TS300将恒温和振荡两种功能完美地结合在一起，极大地缩短了实验操作的时间，是样品孵化、催化、混匀及保存等反应过程理想的自动化工具。
本产品具有以下特点：
●简单易用的人机操作界面，实时显示全部运行信息和设置信息，方便用户观
察设备运行状态。
●一次可处理4块酶标板或者深孔板。
●采用直流无刷电机，噪音低、干扰小、免维护。
●采用热盖加热技术。
●支持自动预热功能。
●支持断电自动恢复功能。
●自带温度校准功能。
●内置软件和硬件双重超温保护装置，使用更可靠。
2．正常工作条件
使用环境温度：0︒C ~ 35︒C
相对湿度：≤70%
使用电源：AC220V/50-60HZ
3. 基本参数。
Infinite 200 介绍
目录Infinite 200 Pro多功能微孔板检测仪简介3 M200 Pro和F200 Pro的性能和技术指标5技术详解91.关于M200 Pro的四光栅系统92.关于M200 Pro的荧光顶部Z轴自动连续聚焦103.关于F200 Pro的优异性价比114.关于F200 Pro的智能滤光片盒115.关于荧光底部的Optimal read126.关于Infinite 200 Pro的发光光路127.关于Nanoquant微量检测板138.关于GCM14销售策略151.产品定位与目标用户152.关键卖点15Infinite 200 Pro多功能微孔板检测仪简介Infinite系列多功能微孔板检测仪由Tecan集团下属的奥地利公司设计并生产。
秉承Tecan对创新和性能的一贯追求，Infinite系列产品包括了多项先进技术，并提供一流的检测灵敏度和稳定性。
Infinite 200 Pro包括M和F两个型号，分别对应光栅型（monochromator）和滤光片型（filter）。
由于采用先进的模块化的设计，不仅能满足当今科研领域的多样化需求，提供了灵活、可扩展的配置方案，还能保证各项功能都获得最佳的检测效果。
Infinite M200 Pro光栅型多功能检测仪提供以下检测功能：●全波长连续可调的光吸收检测●全波长连续可调的荧光顶部检测●全波长连续可调的荧光底部检测●全波长连续可调的时间分辨荧光检测●荧光顶部自动Z轴聚焦●OR（Optimal Read）增强荧光底部检测●闪光和辉光型发光检测，包括双色发光和BRET●支持6-384孔、立式比色杯和卧式比色杯●Nanoquant 微量检测板，可进行核酸、蛋白定量，及荧光探针标记效率测定●气体控制模块，可控制仪器内部O2和CO2浓度●有效的温控和振幅可调的振荡功能●双自动进样器Infinite F200 Pro滤光片型多功能检测仪提供以下检测功能：●光吸收检测，滤光片覆盖紫外至远红外●荧光顶部检测，滤光片覆盖紫外至远红外●荧光底部检测，滤光片覆盖紫外至远红外●时间分辨荧光检测，●均相时间分辨荧光检测●荧光偏振检测●AlphaScreen/AlphaLISA检测●OR（Optimal Read）增强荧光底部检测●智能滤光片盒，内置芯片记录滤光片信息，仪器自动识别●闪光和辉光型发光检测，包括双色发光和BRET●支持6-384孔和卧式比色杯●Nanoquant 微量检测板，可进行核酸、蛋白定量●气体控制模块，可控制仪器内部O2和CO2浓度●有效的温控和振幅可调的振荡功能●双自动进样器Infinite 200 Pro系列的突出特点Infinite M/F200 Pro专注于仪器性能以及科学家的需求，受到严肃、有经验、追求优异实验结果的科学家的深度认可。
ZWFR-200多振幅轨道摇床(触摸式彩屏)和多振幅轨道摇床(触摸式彩屏)价格
标题：ZWY-211D脚踏开门型大容量全温度恒温摇床
产品介绍ZW卧式摇床是专为现代生物工程生产单位研制开发的一款大容量恒温培养制取设备。该设备腔体空间大、装瓶数量多，特别适合于中试及批量生产。其中：ZWY-211B/111B是标准型，最大装瓶规格为1000ml；ZWY-211C/111C是加高型，该型号产品被列为“上海市抗击非典重点新产品”，最大装瓶规格为5000ml；ZWY-211D/111D为脚踏开门型，人性化的设计可使实验人员即使双手持瓶也可方便的打开摇床箱盖，该型号产品最大装瓶规格为5000ml；ZWF-211/111是往复振荡型，最大装瓶规格为5000ml，特别适合发酵和制药行业使用。技术特点智能化声光报警环境扫描微处理控制器LCD大屏幕背光液晶显示屏显示各设定参数和实测参数运行参数加密锁定，避免人为误操作运行参数记忆...
厂家：南北容量恒温摇床
标题：ZWY-111B豪华型大容量恒温摇床
产品介绍ZW卧式摇床是专为现代生物工程生产单位研制开发的一款大容量恒温培养制取设备。该设备腔体空间大、装瓶数量多，特别适合于中试及批量生产。其中：ZWY-211B/111B是标准型，最大装瓶规格为1000ml；ZWY-211C/111C是加高型，该型号产品被列为“上海市抗击非典重点新产品”，最大装瓶规格为5000ml；ZWY-211D/111D为脚踏开门型，人性化的设计可使实验人员即使双手持瓶也可方便的打开摇床箱盖，该型号产品最大装瓶规格为5000ml；ZWF-211/111是往复振荡型，最大装瓶规格为5000ml，特别适合发酵和制药行业使用。技术特点智能化声光报警环境扫描微处理控制器LCD大屏幕背光液晶显示屏显示各设定参数和实测参数运行参数加密锁定，避免人为误操作运行参数记忆...
微孔板快速振荡器 检验标准
微孔板快速振荡器检验标准
摘要：
一、微孔板快速振荡器的工作原理与作用
二、微孔板快速振荡器的分类与特点
三、微孔板快速振荡器的使用方法与操作步骤
四、微孔板快速振荡器的维护与注意事项
五、微孔板快速振荡器的检验标准与要求
正文：
微孔板快速振荡器是一种实验室常用的设备，其工作原理是通过电机驱动振荡装置，使微孔板在设定的温度和湿度条件下进行快速振荡，以达到实验目的。
微孔板快速振荡器在医学、生物学、化学等领域都有着广泛的应用。
微孔板快速振荡器有多种分类，可以根据振荡频率、温度范围、体积等不同特点进行分类。
例如，根据振荡频率可分为低频振荡器、中频振荡器、高频振荡器；根据温度范围可分为常温振荡器、高温振荡器、低温振荡器等。
不同类型的微孔板快速振荡器适用于不同的实验需求。
微孔板快速振荡器的使用方法相对简单，一般来说，首先需要将微孔板放入振荡器中，然后设定振荡条件，启动振荡器，最后取出微孔板即可。
在使用过程中，需要注意操作步骤的规范性，以保证实验结果的准确性。
微孔板快速振荡器的维护也非常重要，一般来说，需要定期清洁振荡器，避免灰尘和污垢影响振荡效果。
此外，还需要定期检查振荡器的电路和机械部件，确保其正常工作。
微孔板快速振荡器的检验标准主要包括振荡频率、振荡幅度、温度控制精度等。
在购买微孔板快速振荡器时，需要根据实验需求选择符合检验标准的设备，以确保实验结果的准确性。
总之，微孔板快速振荡器是一种非常重要的实验室设备，其工作原理、分类、使用方法、维护以及检验标准都需要我们掌握。
数显恒温振荡器(摇床)
4
79-2
双向磁力加热搅拌器
最大搅拌容量1000ml ，加热功率200W ，调速范围0 ～2400 转／分，正反方向工作
480
5
78HW-1
恒温磁力搅拌器
最大搅ห้องสมุดไป่ตู้容量1000ml ，电子控温，室温～l00℃，加热功率：200W ，调速0～2400转／分
400
6
79HW-1
恒温磁力搅拌器
最大搅拌容量1000ml，电子控温，室温～100℃，加热功率：250W ，调速0～2400转／分
980
15
HJ-4A
数显恒温多头磁力搅拌器
最大搅拌容量4×1000ml ，数显控温室温～100℃，加热4×200W ，调速范围：0 ～2400转／分
2380
16
HJ-5
数显恒温多功能搅拌器
具有电动、磁力双重搅拌功能，数显控温常温～100℃，无级调速
980
l7
HJ-6
多头磁力加热搅拌器
最大搅拌容量6×1000ml ，加热功率：6×200W ，调速范围：0 ～2400 转／分
最大搅拌容量1000ml ，数显控温，室温～100℃，加热功率：300W ，数显测速
980
10
HJ-1
磁力搅拌器
分两种规格，最大搅拌容量500ml , 1000ml ，调速范围：0～2400 转／分
260
11
HJ-2
双头磁力加热搅拌器
最大搅拌容量2×1000ml ，加热功率：2×150W ，调速范围：0～2400 转／分
960
8
HY - 4
往复式调速多用振荡器
工作方式：水平往复，定时范围：0 ～120 分，工作频率：起动～320 次／分
MB100-4A微孔板恒温振荡器和微孔板恒温振荡器价格
标题：微孔板孵育器--MK100-4P
产品简介微孔板恒温孵育器采用微处理技术结合PID控制方式而形成的微孔板孵育器。主要用于酶标板（96孔/384孔板）、细胞培养板（24孔板、48孔板、96孔板等）等溶液在适当温度下进行培养孵育。产品特点1．LCD液晶显示，人机友好的触摸式操作界面2．对微孔板进行上下加热功能，使得微孔板的每个孔能够均匀地被加热3．微处理器控制温度和时间，温控线性好、波动小4．可同时显示设置和实际温度、时间参数5．可放4个标准酶标板和微孔板，程序运行结束后发出声音报警讯号性能指标1．温度控制范围：室温℃2．温度均匀性：≤±0.5℃3．温度稳定性：≤±0.2℃4．加热平台温度准确度：<0.5℃（在37℃下检测）5．升温速度：＜25 min (从20℃to 60...
厂家：南北
产品简介K37微板孵育器采用用微处理技术结合PID控制方式而形成的多用途37℃血型卡孵育器。适用用于酶标板、细胞培养板、血型试剂卡、烧杯、培养皿等载体内溶液在37℃温度下进行培养孵育。产品特点1．LCD液晶显示2．具有对酶标板、细胞培养板、血型试剂卡进行加热恒温功能3．仪器内可存放微孔板架，也可存放标准化血型卡盘，多卡同时孵育，提高工作效率4．微处理器控制温度、时间，温控线性好、波动小5．使用安全，性能可靠，自动计时并有报警提示6．外观简洁大方，透明上盖，实验过程一目了然性能指标1.温度控制范围：37℃2.温度均匀性：≤±0.5℃3.温度稳定性：≤±0.2℃4.温度准确度：<0.5℃5.容量：可放置微孔板、试剂卡架、烧...
厂家：南北100-4P
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
TS200 微孔板恒温振荡器是一款采用直流无刷电机和PID智能控温技术相结合的实验室仪器。
它具有体积小、重量轻、无污染；温度、时间LCD显示，美观大方，操作简单等特点。
主要用于酶标板（96孔/384孔板）、细胞培养板（24孔板、48孔板、96孔板等）等样品在适当温度下进行细胞的培养孵育和振荡。
产品具有以下特点：
●LCD实时显示系统运行状态和参数值。
●采用高品质开关电源，整机长期运行稳定可靠。
●采用一键式旋钮操作，简单易用。
●具有断电恢复功能，当外电源断电又重新来电时，设备可按原设定程序
自动恢复运行；
●微处理器控制，温控线性好、波动小；
●可在0~100小时范围内任意设定培养时间，定时结束后，自动发出提示
音。
●双层的加热系统，保证恒温培养的稳定性。
●直流无刷电机，免维护，低噪音。