汽车常用术语
68个汽车专业名词术语详解

MPVMPV的全称是Multi-Purpose Vehicle,即多用途汽车。
它集轿车、旅行车和厢式货车的功能于一身,车内每个座椅都可调整,并有多种组合的方式,例如可将中排座椅靠背翻下即可变为桌台,前排座椅可作180度旋转等。
近年来,MPV趋向于小型化,并出现了所谓的S-MPV,S是小(Small)的意思。
S-MPV 车长一般在(4.2-4.3)m之间,车身紧凑,一般为(5—7)座。
SUVSUV的全称是SportUtility Vehicle,中文意思是运动型多用途汽车。
现在主要是指那些设计前卫、造型新颖的四轮驱动越野车。
SUV一般前悬架是轿车型的独立悬架,后悬架是非独立悬架,离地间隙较大,在一定程度上既有轿车的舒适性又有越野车的越野性能。
由于带有MPV式的座椅多组合功能,使车辆既可载人又可载货,适用范围广。
RVRV的全称是Recreation Vehicle,.即休闲车,是一种适用于娱乐、休闲、旅行的汽车,首先提出RV汽车概念的国家是日本。
RV的覆盖范围比较广泛,没有严格的范畴。
从广义上讲,除了轿车和跑车外的轻型乘用车,都可归属于RV。
MPV及SUV也同属RV。
皮卡皮卡(PICK-UP)又名轿卡。
顾名思义,亦轿亦卡,是一种采用轿车车头和驾驶室,同时带有敞开式货车车厢的车型。
其特点是既有轿车般的舒适性,又不失动力强劲,而且比轿车的载货和适应不良路面的能力还强。
最常见的皮卡车型是双排座皮卡,这种车型是目前保有量最大,也是人们在市场上见得最多的皮卡。
CKD汽车CKD是英文Completely Knocked Down的缩写,意思是“完全拆散”。
换句话说,CKD汽车就是进口或引进汽车时,汽车以完全拆散的状态进入,之后再把汽车的全部零、部件组装成整车。
我国在引进国外汽车先进技术时,一开始往往采取CKD组装方式,将国外先进车型的所有零部件买进来,在同内汽车厂组装成整车。
SKD汽车SKD是英文Semi-Knocked Down的缩写,意思是“半散装”。
汽车行业常用术语(汽车知识、车辆知识、学习汽车、了解汽车行业常用术语)

RV的全称是Recreati&aVehicle,.即休闲车,是一种适用于娱乐、休闲、旅行的汽车,首先提出RV汽车概念的国家是日本。RV的覆盖范围比较广泛,没有严格的范畴。从广义上讲,除了轿车和跑车外的轻型乘用车,都可归属于RV。MPV及SUV也同属RV。
14.汽车导航系统
GPS是以全球24颗定位人造卫星做基础,向全球各地全天候地提供三维位置、三维速度等信息的一种无线电导航和定位系统。GPS的定位原理是:用户接收卫星发射的信号,从中获取卫星与用户之间的距离、时钟校正和大气校正等参数,通过数据处理确定用户的位置。现在,民用GPS的定位精度可达10m以内厶GPS具有的特殊功能很早就引起了汽车界人士的关注,当美国在海湾战争后宣布开放一部分GPS的系统后,汽车界立即抓住这一契机,投入资金开发汽车导航系统,对汽车进行定位和导向显示,并迅速投入使用。汽车GPS导航系统由两部分组成:一部分由安装在汽车工的GPS接收机和显示设备组成;另一部分由计算机控制中心组成,两部分通过定位卫星进行联系。计算机控制中心是由机动车管理部门授权和组建的,它负责随时观察辖区内指定监控的汽车的动态和交通情况,因此整个汽车导航系统起码有两大功能:一个是汽车踪迹监控功能,只要将已编码的GPS接收装置安装在汽车上,该汽车无论行驶到任何地方都可以通过计算机控制中心的电子地图上指示出它的所在方位;另一个是驾驶指南功能,车主可以将各个地区的交通线路电子图存储在软盘上,只要在车工接收装置中插入软盘,显示屏上就会立即显示出该车所在地区的位置及目前的交通状态,既可输入要去的目的地,预先编制出最佳行驶路线,又可接受计算机控制中心的指令,选择汽车行驶的路线和方向。
一般说,在制动力缓缓施加的情况下,ABS多不作用,只有在制动力猛然增加使车轮转速骤消的时候ABS才发生效力。ABS的另一主要功效是制动的同时打方向躲避障。因此,在制动距离较短,无法避免触障时,迅速制动转向,是避免事故的最佳选择。值得注意的是,汽车装有ABS,并不代表就一切万事大吉了。所以在此奉劝装有ABS系统的车主,万不可放心大胆地超能力驾驶,引发事故,也许ABS也救不了你。
汽车行业专业术语

汽车行业专业术语1.整车装备质量(kg):汽车完全装备好的质量,包括润滑油、燃料、随车工具、备胎等所有装置的质量。
2.最大总质量kg:汽车满载时的总质量。
3.最大装载质量kg:汽车在道路上行驶时的最大装载质量。
4.最大轴载质量(kg):汽车单轴所承载的最大总质量。
与道路通过性有关。
5.车长mm:汽车长度方向两极端点间的距离。
6.车宽mm:汽车宽度方向两极端点间的距离。
7.车高mm:汽车最高点至地面间的距离。
8.轴距mm:汽车前轴中心至后轴中心的距离。
9.轮距mm:同一车桥左右轮胎胎面中心线间的距离。
10.前悬mm:汽车最前端至前轴中心的距离。
11.后悬mm:汽车最后端至后轴中心的距离。
12.最小离地间隙mm:汽车满载时,最低点至地面的距离。
13.缸数:汽车发动机常用缸数有3、4、5、6、8缸。
排量1升以下的发动机常用3缸,2.5升一般为4缸发动机,3升左右的发动机一般为6缸,4升左右为8缸,5.5升以上用12缸发动机。
一般来说,在同等缸径下,缸数越多,排量越大,功率越高;在同等排量下,缸数越多,缸径越小,转速可以提高,从而获得较大的提升功率。
14。
气缸的排列形式:一般5缸以下的发动机的气缸多采用直列方式排列,少数6缸发动机也有直列方式的。
直列发动机的气缸体成一字排开,缸体、缸盖和曲轴结构简单,制造成本低,低速扭矩特性好,燃料消耗少,尺寸紧凑,应用比较广泛,缺点是功率较低。
直列6缸的动平衡较好,振动相对较小。
大多6到12缸发动机采用V形排列,V形即气缸分四列错开角度布置,形体紧凑,V形发动机长度和高度尺寸小,布置起来非常方便。
V8发动机结构非常复杂,制造成本很高,所以使用的较少,V12发动机过大过重,只有极个别的高级轿车采用。
15。
气门数:国产发动机大多采用每缸2气门,即一个进气门,一个排气门;国外轿车发动机普遍采用每缸4气门结构,即2个进气门,2个排气门,提高了进、排气的效率;国外有的公司开始采用每缸5气门结构,即3个进气门,2个排气门,主要作用是加大进气量,使燃烧更加彻底。
汽车专业术语汇总

涂料与辅料术语
涂料:用于涂覆在汽车表面,起到保护、装饰和标识等作用的液态材料 辅料:用于辅助涂装过程的材料,如稀释剂、固化剂、催化剂等 涂层:涂料涂覆在汽车表面形成的一层薄膜,具有耐候、防腐、美观等功能 涂装工艺:汽车表面涂装的过程和方法,包括前处理、底漆、面漆、清漆等工序
涂装设备与工具术语
喷枪:用于涂 装的主要工具, 根据涂料性质 和涂装要求选 择合适的喷枪。
压缩空气供应 系统:提供稳 定的压缩空气, 确保喷涂效果
均匀。
涂料储存设备: 储存各种涂料, 确保涂料的质 量和稳定性。
烘干设备:用 于涂料的烘干, 根据涂料的性 质和涂装要求 选择合适的烘
干设备。
04
汽车销售与客户服务
汽车销售流程术语
潜在客户:有购 买意向但尚未成 为客户的个人或 企业
客户开发:通过 各种方式寻找潜 在客户并建立联 系
故障码:汽车电子控制系统中的故障代码,用于诊断故障。 诊断工具:用于检测汽车故障的工具,包括万用表、示波器等。 排放控制:汽车排放控制系统的维护和修理,包括三元催化器、氧传感器等。 发动机性能:发动机性能的检测和调整,包括点火正时、气门间隙等。
维修安全与环保术语
维修安全术语: 汽车维修时必须 遵循的安全操作 规程和注意事项, 如佩戴防护眼镜、 手套等个人防护 用品,以及使用 专用工具和设备
05
汽车行业法规与标准
国家汽车标准与法规
制定机构:国家标准化管 理委员会
目的:规范汽车行业生产、 销售、使用等环节
标准内容:涉及汽车安全、 环保、节能等方面
法规内容:涉及汽车行业 监管、市场准入等方面
国际汽车标准与法规
国际汽车标准组织:ISO/TC22
国际汽车法规体系:联合国世界车辆法规协调论坛(UN WP.29)
汽车--常用术语

汽车--常用术语常用术语1、汽车类型:the type of automobile汽车:motor vehicle,automobile载货车:truck 微型货车:mini-truck 轻型货车:light-truck中型货车:medium truck 重型货车:heavy truck 越野车:off-road vehicle自卸车:dump truck 牵引车:towing vehicle专用汽车:special purpose vehicle 客车:bus 轿车:passenger car微型轿车:mini-car 普通级轿车:subcompact car 中级轿车:compact car中高级轿车:intermediate car 高级轿车:limousine car2、汽车尺寸:dimension of vehicle车长:vehicle length 车宽:vehicle width 车高:vehicle height轴距:wheel space 轮距:track 前悬:front overhang后悬: rear overhang 最小离地间隙:ground clearance车轮外倾:camber angle 主销内倾: kingpin inclination 前束toe-in3、发动机:engine发动机总体构造和工作原理:the construction and working principle汽油机gasoline engine 柴油机diesel engine四冲程发动机four-stroke engine 单(多)缸发动机single(multi)-cylinder engine 立(斜、卧)式发动机vertical (inclined、horizontal) engine工作循环working process进气(压缩、膨胀、排气)行程suction(compression、expansion 、exhaust) stroke 点火次序firing order 上(下)止点top(bottom) dead centre活塞行程piston stroke 气缸工作容积piston swept volume发动机排量engine swept volume 充气系数volumetric efficiency配气相位valve timing 压缩比compression ratio直接喷射direct injection 间接喷射indirect injection喷油压力injection pressure 电控喷射electronic-controlled injection雾化atomization 混合气浓度mixture concentration可燃混合气combustible mixture 空燃比air-fuel ratio过量空气系数excess air ratio 燃烧室combustion chamber压燃compression ignition 点燃spark ignition抗暴性antiknock quality 增压中冷inter-cooling负荷load 空载no-load工况working condition曲柄连杆机构:connecting rods and crankshaft缸盖cylinder head 气缸cylinder缸体cylinder block 缸套cylinder liner油底壳oil pan 活塞piston活塞环(销) piston ring(pin) 气(油)环compression(oil control) ring连杆connecting rod 曲柄crank曲轴crankshaft 飞轮flywheel配气机构:valve gear凸轮(轴)cam(camshaft) 进(排)气阀inlet (exhaust) valve挺柱tappet 推杆push-rod摇臂rocker arm燃油供给系统:fuel system柱塞(转子)式喷油泵jerk fuel injection pump喷油器injector 调速器governor发动机调速系统:engine speed governing排放控制系统:emission control system发动机冷却系统:engine cooling system发动机润滑系统:engine lubrication system发动机点火系统:engine ignition system发动机起动系统:engine starting system5※<标题二>4、汽车底盘术语离合器:clutch摩擦离合器friction clutch(单盘single plate、双盘twin double plate、多盘multi-plate、膜片弹簧diaphragm spring、自动automatic、电磁electromagnetic)离合器操纵机构clutch operation 压盘pressure plate分离杆release lever 分离筒release sleeve离合器盖clutch cover 从动盘clutch plate从动盘毂clutch plate hub 分离弹簧(轴承)release spring(thrust bearing)中间压盘center plate 压紧弹簧pression减振弹簧damping spring 摩擦片plate friction lining扭转减振器torsional damping arrangement变速器:transmission, gearbox机械式变速器mechanical transmission自动变速器automatic transmission主(副)变速器basic(splitter) transmission行星齿轮变速器planetary transmission液力偶合器fluid coupling 液力变矩器torque converter万向传动装置:十字轴(非等速、等速、准等速、挠性、双联、球销、球笼)万向节cardan (nonconstant velocity、constant velocity、near constant velocity、flexible、double cardan、ball and trunnion、rzeppa) universal joint十字轴总成cross assembly 万向节叉yoke驱动桥:driving axle断开(非断开)式驱动桥divided (rigid) drive axle单(双)级主减速器single (double) reduction final axle齿轮(防滑、自锁、摩擦)差速器gear (limited-slip、self-locking、multi-disc) differential 桥壳axle housing全浮(半浮)式半轴full-floating (semi-floating) axle shaft转向系:steering system机械(动力)转向系manual (power) steering system 转向器steering gear转向盘(轴、操纵机构) steering wheel (shaft、control mechanism)循环球-齿条齿扇(齿轮齿条)式转向器recirculating ball-rack and sector (rack and pinion ) steering gear正(逆)效率forward(reverse) efficiency行驶系:running system独立(非独立)悬架indepenndent (rigid axle) suspension钢板(螺旋、扭杆、空气、橡胶、油气)弹簧leaf(coil、torsion bar、air、rubber、hydro-pneumatic) spring减震器shock absorber 横向稳定器stabilizer anti-roll bar制动系:braking system鼓(盘)式制动器drum (disk) brake 驻车制动装置parking braking device制动鼓(蹄、钳)brake drum (shoe、caliper)5※<标题三>《汽车理论》1 汽车动力性vehicle tractive performance2 加速时间time of acceleration3 最大爬坡度maximum grade ability4 驱动力tractive force5 发动机的调速特性fixed throttle characteristics6 适应性系数adaptive coefficient7 机械效率mechanical efficiency8 行驶阻力resistance 9 滚动阻力rolling resistance10 弹性迟滞elastic slow-moving 11 滚动阻力矩moment of rolling resistance12 滚动阻力系数coefficient of rolling resistance13 切向反力tangential force 14 法向反力normal force15 空气阻力aerodynamic resistance16 空气阻力系数aerodynamic resistance coefficient17 坡道阻力grade resistance 18 道路阻力resistance of the road19 加速阻力accelerating resistance;inertia force20 旋转质量换算系数correction coefficient of rotating mass21 附着力adhesive force 22 切向反作用力tangential force23 法向反作用力normal force 24 附着系数coefficient of adhesion25 后备功率power reserve 26 发动机比功率power/mass ratio27 燃料经济性fuel economy 28 燃油消耗率specific fuel consumption29 万有特性cross sectional characteristics30 负荷特性part throttle characteristics31 道路循环油耗fuel economy of road test cycles32 制动性braking performance 33 地面制动力type-ground braking force34 制动器制动力braking force originated from brake system35 制动减速度braking deceleration 35 制动距离braking distance37 同步附着系数synchronizing adhesion coefficient38 侧倾角速度roll velocity 39 俯仰角速度pitch velocity40 横摆角速度yaw velocity 41 轮胎坐标系tire axis system42 轮胎侧偏角side-slip-angle 43 侧偏刚度cornering stiffness44 回正力矩aligning torque 45 转向特性steering characteristics46 侧偏力cornering force 47 横摆角速度增益yaw velocity gain48 临界车速critical speed 49 特征车速characteristic speed50 不足转向under steer 51 过多转向over steer52 中性转向neutral steer 53 静态储备系数static margin54 瞬态响应transient state response 55 稳态响应steadies state response56 汽车平顺性ride of the automobile57 路面谱spectrum of road surface roughness58 空间频率spatial spectral density 59 空间频率谱spatial spectral density60时间频率谱spectral density 61 最小离地间隙ground clearance62 汽车的通过性mobility over unprepared terrain63 纵向通过角ramp angle 64 接近角approach angle65 离地角departure angle 66 最小转弯直径diameter of turning circle67 转弯通道圆turning clearance circle 68 功率循环circulation of power69 牵引阻力tractive resistance 70 牵引力(功率)曲线图tractive-power chart71 最高车速maximum velocity 72 发动机外特性engine characteristic at maximum opening of valve73 制动效能brake efficiency 74 转向稳定性cornering stability75 后轴侧滑sideslip of rear axle 76 甩尾trail swing77 评价指标evaluated standard 78 操纵稳定性steering stability81 主销后倾kingpin caster 82 主销内倾kingpin inclination83 功率平衡图tractive and resistance power graph84 动力因数dynamical factor85 制动跑偏braking deviation from 86 制动力分配brake banlance87 制动防抱死ABS(Anti-lock Braking System)88动力特性dynamical characteristics89 横向稳定性stability of landscape orientation90 侧偏特性cornering characteristics91 轮胎花纹tire pattern 92 汽车技术状况technical condition of vehicle 93 暴露极限exposure boundary 94 发动机测功器engine dynamometer95 发动机综合试验机motor analyze / engine analyzer96 底盘测功器chassis dynamometer97 车轮功率平衡机dynamic wheel balancer98 前束量尺toe-in ganger 99 外倾测量器camber gauge100 红外线废气分析仪infrared rays exhaust gas analysis apparatus疲劳-降低工作效率界限fatigue-decreased proficiency boundary舒适降低界限decreased comfort boundary5※<标题四>《汽车设计》绪论introduction全球定位系统Global Position System计算机辅助设计Computer Aided Design自适应巡航控制系统Autonomous Intelligent Cruise Control电子伺辅开车Drive by wire防抱死制动系统Anti-block Brake System主动悬架Active Suspension被动悬架Passive Suspension半主动悬架Semi-Active Suspension自动变速器Automatic Transmission电控转向系统Electronic Control Steering通用汽车公司General Motors Company成本竞争能力Cost Competitiveness成本杀手Cost killer运动型多用途车Sport & utility vehicle概念设计Concept Design前置前驱Front-engine Front-drive前置后驱Front-engine Rear-drive后置后驱Rear-engine Rear-drive中置后驱Middle-engine Rear-drive全轮驱动Full-wheel-drive长头式Cab-behind-engine truck平头式forward control layout cab or cab forward type 短头式short bonneted type轴距wheel base轮距wheel center distance装载量weight-carrying capacity整车整备质量weight empty总质量weight in running order轴荷分配axle load ( weight)直接档direct drive燃油经济性fuel economy百公里油耗fuel consumption of 100km通过性throughput capacity最小转弯半径minimum negotiable radius总体布置general arrangement纵梁frame side member or frame girder member横梁frame cross member离合器设计clutch design从动盘clutch driven plate or clutch spider膜片弹簧diaphragm spring压盘pressure plate摩擦片clutch facing从动钢片clutch cushion disk or cushion spring扭转减振器torsion vibration damper or torsion damper 花键毂splined hub变速器设计transmission design中间轴式变速器countershaft transmission直齿spur gear斜齿圆柱齿轮helical gear换档机构gear shift mechanism直齿滑动齿轮shifting slider gear啮合套shifter collar同步器synchronizer轴承bear飞溅润滑plash oiling压力润滑full pressure oiling 换档位置图gear shifting diagram 第一轴input shaft中间轴counter shaft第二轴output shaft万向节设计universal joint柔性万向节rubber universal joint刚性万向节rigid cardan驱动桥drive axle主减速器final gear差速器differential车轮传动wheel driver驱动桥壳rear-axle housing整体式驱动桥壳one-piece housing 主减速比final drive ratio螺旋锥齿轮helical bevel gear双曲面齿轮hypoid bevel gear圆柱齿轮helical spur gear蜗轮蜗杆worm-and-gear (wheel)行星齿轮planetary gear最小离地间隙minimum ground clearance of rear axle摩擦片式差速器sure-grip differential半轴half rear axle悬架设计suspension design弹性元件springs导向机构guider减振器absorber缓冲块bumper横向稳定杆stabilizer钢板弹簧spring leaf螺旋弹簧spiral spring扭杆弹簧torsion bar spring橡胶弹簧rubber spring空气弹簧air spring油气弹簧oiliness spring横向摆臂式独立悬架ndependent wheel suspension by swinging arms 纵向摆臂式独立悬架independent suspension by swinging arms 不等长双横臂式独立悬架long and short arm suspension烛式悬架suspension stuck麦克弗逊式独立悬架suspension McPherson strut 平衡式独立悬架stabilizator suspension主簧mail leaf of spring副簧helper spring制动系brake system制动器brake驱动机构drive unit制动效能braking efficiency领从蹄式制动器leading-trailing shoe brake双领蹄式制动器two leading shoe brake单向增力式制动器half-servo brake横向稳定杆stabilizer bar准双曲面齿轮hypoid gear万向节轴cardan花键spline5※<标题五>《随机振动》1、Random Vibration 随机振动2、Probability 概率3、Statistics 统计4、Random Process 随机过程5、Density 密度6、Frequency 频率7、Discrete 离散8、Wave 波动9、Continuous model 连续模型10、Dynamic 动力的11、Structure 结构12、Dynamic Analysis 动力学分析13、Acceleration 加速度14、Gravitational Acceleration 重力加速度15、Definite Function 有限方程16、Excitation 激励17、Response 响应18、Discrete Model 离散模型19、Stationary 平稳的20、Nonstationary 非平稳的21、Rigid Body 刚体22、Correlation Function 相关函数23、Autocorrelation 自相关24、Spectral Density 谱密度25、Power Spectrum 功率谱26、Ergodic 各态历经的27、Temporal 短时的28、Limitation 极限29、Mean 均值30、Mean Square 均方值31、Variance 方差32、Covariance 协方差33、Variable 变量34、Constant 常数35、Single 单独的36、Filter 过滤37、Cross Correlation 互相关38、Second Order 二阶39、Lag 间隙40、Regular 规律的41、Irregular 不规则的42、Property 特性43、Performance 性能44、Ensemble 整体的45、Even 偶的46、Odd 奇的47、Independent 独立的48、Zero Mean 零均值49、Scatter 离散的50、Period 周期51、Sample 样本52、Uniform 均匀的53、Absolute 绝对值54、Phase 相位55、Circular Frequency 圆频率56、Distributed 分布的57、Dirac Delta Function 狄拉克?得尔塔函数58、Magnitude 模59、Infinite 无穷的60、Periodic 周期的61、Finite 有限的62、Restriction 约束63、Evaluation 估计64、Time Domain 时域65、Frequency Domain 频域66、Fourier Series 富里叶级数67、Fourier Integral 富里叶积分68、Piecewise 分段的69、Fourier Coefficient 富里叶系数70、Complex Number 复数值71、Complex Function 复数函数72、Real Function 实数函数73、Conjugate 共轭74、Parseval’s Formula 帕舍伐尔公式75、Amplitude 振幅76、Impulse 脉冲77、Complex Frequency 复数频域的78、Ordinate 坐标79、Singularity 奇异点80、Harmonic 谐波的81、Narrow Band 窄带82、Wind Band 宽带83、Exponent 指数84、Derivation 导数85、Joint Probability 联合概率分布86、Linear 线性的87、Superposition 重叠88、Inverse Transform 逆变换89、Single Degree of Freedom 单自由度90、Natural Frequency 自然频率91、Damp 阻尼92、Critical 临界的93、Displacement 位移94、Velocity 速度95、Unit Impulse 单位脉冲96、Momentum 动量97、Ordinary Differential Equation 常微分方程98、Complex Frequency Response Function 复频响应函数99、Algebraic Equation 代数方程100、Peak 峰值5※<标题六>《汽车电器设备》蓄电池accumulator电解液electrolyte电路electric circuit开关switch电流表ammeter电压表voltmeter电能electric energy化学能chemical energy电流强度current intensity 脉冲电流pulse current正极板positive plate负极板negative plate单格电池cell比重计hydrometer电极electrode电荷electric charge阳极positive electrode阴极negative electrode电路图circuit diagram电器electric equipment电压voltage电位差potential difference 电源power source充电系charging system交流发电机alternator充电指示器charge indicator 交流电alternating current 直流电direct current二极管diode三极管triode电压调节器voltage regulator 过充电overcharge转子rotor定子stator皮带轮pulley警告灯warning lamp保险丝fusible link短路short circuit电动势electro-motive force 起动系starting system电磁开关magnetic switch起动机马达starter motor机械能mechanical energy飞轮flywheel电磁场electromagnetic field 换向器commutator电刷brush继电器relay电枢armature小齿轮pinion电枢轴armature shaft电刷弹簧brush spring轴承bearing单向离合器overrunning clutch 换档机构shift mechanism电磁线圈solenoid压缩比compression ratio飞轮齿圈flywheel ring gear电枢绕组armature windings换向器片commutator segments 点火系ignition system点火开关ignition switch火花塞spark plug电容器condenser分电器distributor分电器盖distributor cap点火线圈ignition coil初级绕组primary winding次级绕组secondary winding断电器breaker电磁铁electromagnet断电器触点breaker points电火花electric spark分电器点火系统distributor ignition system 空燃比air-fuel ratio火花塞间隙air gap高压high voltage低压low voltage分火头distributor rotor高压线spark plug wire分电器凸轮distributor cam附加电阻ballast resistor点火提前spark advance离心提前centrifugal advance真空提前vacuum advance大气压atmospheric pressure照明lighting照明灯light bulb信号signal报警装置warning equipment仪表meter仪表板instrument panel指示器indicator指示板indicator board指针needle控制电路control circuit辅助设备auxiliary equipment汽油机gasoline engine柴油机diesel engine汽油泵gasoline pump电磁学electromagnetism电磁波electromagnetic wave晶体管点火系统transistorized ignition system无触点电子点火系统breakerless electronic ignition system电磁感应electromagnetic5※<标题七>《汽车电控原理及应用》进气温度(ACT)Air Charge Temperature空气流量传感器(AFS)Air Flow Sensor叶板式空气流量计(V AM)Vane Airflow Meter绝对压力传感器(AIV)Absolute Pressure Sensor空气温度传感器(A TS)Air Temperature Sensor进气温度传感器(ITA)Intake Air Temperature Sensor热线式空气流量计(HW AMMF)Hot-Wire Air-Mass Meter Flow热膜式空气流量计(HFAMFM)hot-film air-mass flow meter 卡门空气流量计(KV AFM)Karman vortex air flow meter大气压力传感器(BARO sensor)barometric pressure sensor 大气压力传感器(BP)barometric pressure sensor节气门关闭位置(CTP)closed throttle position进气温度传感器(IATS)intake air temperature sensor怠速空气控制阀(IACV)idle air control valve可变进气相位(VVT)variable valve timing混合气控制(M/C)mixture control节气门体(TB)throttle body节气门位置(TP)throttle position节气门位置传感器(TPS)throttle position sensor节气门位置开关(TPS)throttle position switch节气门电子控制(ETC)electronic throttle control体积空气流量(V AF)volume air flow电控单元(ECU)electronic control unit燃油喷射系统(INJ)injection system中央多点燃油喷射(CMFI)central multipart fuel ignition连续燃油喷射(CIS)continuous fuel injection直接燃油喷射(DFI)direct fuel injection间接燃油喷射(IFI)indirect fuel injection燃油泵(FP)fuel pump多点燃油喷射(MFI)multipart fuel injection单点燃油喷射(SPI)single point injection顺序电控燃油喷射(SEFI)sequential electronic fuel injection电子燃油控制(EFC)electronic fuel control冷起动喷射(CSI)cold star injection机械连续燃油喷射系统K-Jetronic分配式喷油泵(DFIP)distributor fuel injection pump脉冲调制(PWM)pulse width modulation可变截面喷嘴(V AN)variable area nozzle计算机控制点火(C3I)computer controlled coil ignition汽缸识别传感器(CID)cylinder identification sensor曲轴位置传感器(CKP)Sensor crankshaft position sensor有分电器电子点火EI-with distributor无分电器电子点火系统(EDIS)electronic distributorless ignition system 点火控制模块(ICM)ignition control module整体式电子点火(IEI)integrated electronic ignition感应式脉冲发生器Pickup induction pulse generator霍尔式脉冲发生器Hall-type pulse generator发动机转速及曲轴位置传感器Engine-speed and crankshaft position sensor 发动机转速及凸轮轴位置传感器Engine-speed and camshaft position sensor 车速传感器Speed sensor半导体点火系统Semiconductor ignition system霍尔集成电路(Hall IC)Hall integrated circuit霍尔传感器电压Hall sensor voltage点火提前机构Ignition advance mechanism device真空提前机构Vacuum advance mechanism device离心提前机构Centrifugal timing device unit ;centrifugal timer 电子点火系统EI system electronic ignition system闭环控制(CL)closed loop氧传感器(EGOS)exhaust gas oxygen sensor废气再循环阀(EGRV)exhaust gas recirculation valve氧传感器(EGS)exhaust gas sensor三元催化反应器(TWC)three way catalytic converter执行器Actuator温控定时开关Thermo-time switch凸轮轴位置传感器(CMP Sensor)camshaft position sensor 曲轴位置传感器(CKP Sensor)crankshaft position sensor发动机水温传感器(CTS)engine coolant temperature sensor 汽缸位置(CYP)cylinder position爆震传感器(DS)detonation sensor爆震传感器(KS)knock sensor水温传感器(WTS)water temperature sensor怠速控制(IAC)idle air control曲轴箱强制通风(PCV)positive crankcase ventilation自动变速器(A/T)automatic transaxle (transmission)手动变速箱(M/T)manual transmission无级变速器(CVT)continuously variable transmission 液力偶和器(FCPLG)fluid coupling电控变速器(ECT)electronically controlled transmission 空档开关(NPS)neutral position switch停车/空档位置(PNP)P/N park/neutral position手动停车制动器(PBA)parking brake applied变速器转速传感器(TSS)transmission speed sensor变速器电子控制装置Electronic transmission control计算机控制悬架Computer control suspension液力主动悬架Hydraulic active suspension车轮负荷传感器(WL-sensor)wheel-load sensor行程传感器Travel sensor加速度传感器Acceleration sensor载荷传感器Load sensor车身加速度计Body accelerometer车身高度传感器Vehicle height sensor电子空气悬架Electronic air suspension主动式后轮转向系(ARS)active rear steer system四轮转向(4WS)four wheel steering锁定离合器(L/C)lock-up clutch防滑差速器(LSD)limited slip differential动力转向压力开关(P/S)power steer pressure switch动力控制模块(PCM)power train control module踏板行程传感器(PTS)pedal trechometer sensor车速传感器(VSS)vehicle speed sensor减速传感器Deceleration sensor电子控制四轮转向系Electronically controlled 4WS*system 后轮转向角主传感器Main rear wheel angle sensor后轮转向角副传感器Sub rear wheel angle sensor前轮转向角主传感器Front main steer angle sensor前轮转向角副传感器Front sub steer angle sensor5※<标题八>《汽车计算机辅助设计》计算机辅助设计CAD(computer aideddesign)准时制生产Just in time (JIT)专家系统Expert System(ES)人工智能artificial intelligence客户/服务器Client/Server分布式系统distributed System内部网Intranet外部网extranet浏览器Browser服务器Server网络network局域网Local Area Network(LAN)星形网star network topology以太网Ethernet令牌环Token-ring多媒体Multimedia原型法Prototyping生命周期Life cycle类Class自底向上Bottom-up自顶向下Top-down操作系统Operation System硬件Hardware软件Software数据data数据字典data dictionary数据模型data model数据处理data processing数据结构data structure数据仓库data warehousing数据流data flow数据收集Data Gathering数据处理data processing数据冗余data redundancy信息整体性information integrity逻辑Logical物理Physical实体entity联系Relationship属性Attribute电子商务electronic commerce订单处理sales order processing相关干系人stakeholder participation 系统分析System analysis系统设计System design系统实施System implementation系统评估System assessment顺序结构Sequence条件结构condition输入控制input control处理控制Processing control输出控制Output control界面interface文件File文件传输协议File transfer protocol最终用户End-user密码Password代码Code防火墙Firewall条形码bar code外模式External schema概念模式Conceptual Schema内模式Internal Schema第一范式First Normal Form(1NF)主关键字key知识库knowledge base战略计划strategic planning管理控制Management control运行控制Operational Control结构化决策Programmed decisions管理信息系统Management information system(MIS)企业资源计划Enterprise Resource Planning(ERP)最优化技术Optimized Production Technology(OPT)物料需求计划Material Requirements Planning(MRP)制造资源计划Manufacturing Resource Planning (MRPII)客户关系管理Customer Relationship management(CRM)决策支持系统Decision support system(DSS)电子数据传输Electronic data exchange(EDI)办公自动化系统Office Automation system(OAS)开放系统互连Open system Interconnection (OSI)企业流程重组Business Process Reengineering(BPR)结构化系统开发方法Structured System Development Methodology面向对象方法Object-Oriented Method企业系统规划法Business System Planning(BSP)关键成功因素法Critical Success Factors(CSF)数据库管理系统Database management System(DBMS)面向对象的数据库管理系统object-oriented database management systems(OODBMS) 中央处理器Central Processing Units(CPU)数据流程图data flow diagram(DFD)数据模型规范化Data modeling formalism实体-联系图Entity-relationship diagram实体-联系模型Entity-relationship model实体-联系方法Entity-relationship approach软件开发与维护software development and maintenance 结构化程序设计Structured Programming人面相互作用human-computer interaction信息系统外包Outsourcing of information systems信息系统的安全性security of information system管理信息系统的结构the structure of MIS金字塔型的管理信息系统结构the MIS as a pyramid非结构化决策Non-programmed decisions5※<标题九>《汽车优化设计》优化技术optimization technique优化用数学模型mathematical model for optimization 理论分析法theoretical analysis method类比分析法analogy analysis method汽车选型automobile electrotype投资回收期法payback period method寿命周期费用分析法life cycle cost analysis method 年当量费用valent weight cost per year资金回收系数capital reclamation ratio价值分析法value analysis method汽车动力性motor vehicle dynamic characteristics费用效率分析法cost efficiency analysis method选型优化electrotype optimization技术任务书assignment for technical design技术评价technical evaluation经济评价economical evaluation技术经济优化technical economy optimization实验优化experiment optimization单因素优选法single factor selecting method多因素优选法multifactor selecting method正交实验法orthogonal experiment method汽车使用维修优化automobile utilization and repair optimization 线性规划法liner programming technique分级评分法classified graded method维修服务系统repairing service system维修任务与计划的优化repairing task and plan optimization 分枝界限法branch and bound method计划协调技术plan evaluation and review technique工序时间working procedure time概率计算法calculus of probability method加权平均法method of weighted mean工序最早开工期the earliest time of under stream period事件最迟完工期the latest time of completion date人力安排human resource arrangement缺货费OSS (out of stock) fee确定型模型deterministic model允许缺货的经济定货批量模型economical ordering lot model for permit OOS 生产批量模型production lot model批量回扣模型batch commission model随机性模型randomness model概率密度函数function of density of probability质量评估方法quality evaluation method最优质量水平the best quality level客观性原则principle of objectivity可比性原则comparability principle指向性原则directivity principle缺陷系数法defect coefficient method综合评定法evaluate synthetically method更新优化renewal optimization有形损耗physical depreciation无形损耗invisible depreciation疲劳损坏周期damage cycle tiredly汽车折旧和残值automobile depreciation and scrap value余额递减法declining balance method变率递减法diminish rates on cost method固定折旧率stationary depreciation rate更新时机优化renewal time optimization自然寿命natural lifespan经济寿命economical lifespan回归分析法regression analysis method劣化数值法deterioration numerical method年当量费用法annual valent weight cost method 更新方式优化update mode optimization汽车技术改造automobile technical innovation 成本分析法cost analysis method建模modeling模拟法simulation method年当量费用valent weight cost per year现值系数present value ratio现值系数present value ratio权重weighing通过性steering ability可靠性security载质量loading weight维修性maintainability设计优化design optimization 行驶路线driven route开式路线open type route单环式路线single ring route多环式路线multi ring route维修网点repairing block单路排队single line queue多路排队multi line queue任务分配task distribution关键路径法critical path method 流线图stream line diagram行列矩阵cortege matrix成本控制cost control最佳工期optimum duration存储优化storage optimization 保管费storage fee利息费interest fee保险费assurance fee损耗费dissipation fee定货费ordering fee手续费handing fee质量成本quality cost检验成本inspection cost预防成本prevention cost典型性原则model principle定量化原则ration principle残值scrap value前拦板front board后拦板rear gate边板side gateU形螺栓U-bolt铰链knuckle5※<标题十>《汽车排放与噪声控制》公害public hazard大气污染air pollution噪声noise生态平衡ecological balance燃料fuel内燃机internal combustion engine 光化学烟雾photochemical smog汽车保有量retain number of automobile 环境保护environment protecting大气检测air detection大气质量标准Air Quality Standard催化剂catalyst汽油机petrol engine柴油机diesel engine氧化反应oxidizing reaction催化反应catalysis reaction还原反应reduction reaction不完全燃烧incomplete combustion 轻型货车pick up truck微型货车minitype truck重型货车heavy truck越野车cross country vehicle驱动轮driven wheel高级轿车limousine特种用途车special used vehicle底盘chassis传动系power train离合器clutch变速器transmission传动轴transmission shaft万向传动装置universal driven device 驱动桥driving axle行驶系going system车架frame前桥front axle驱动桥driving axle后桥rear axle转向轮steering wheel驱动轮driving wheel前悬架front suspension后悬架back suspension转向系steering system方向盘joystick转向器diverter制动系brake system制动装置braking device车身car body电气设备electric equipment电源power点火系ignition system起动系starting system照明设备lighting device信号设备signaling equipment用电设备consumer活塞行程piston stroke压缩比compression ratio工作循环working cycle充量系数coefficient of charge进气input压缩过程compression燃烧膨胀expand排气exhausting可燃混合气carbureted mixture曲柄连杆机构crank link mechanism 配气机构valve mechanism燃料供给系fuel providing system 冷却系cooling system汽缸cylinder配气相位valve timing凸轮cam充气效率charge efficiency空气滤清器Air Filter空燃比Air-Fuel Ratio混合气浓度mixture strength燃料消耗量fuel consumption润滑系lubrication system润滑油lubricating oil燃烧室combustion chamber有效转矩effective torque有效功率effective power后备功率reserve capability负荷特性load characteristic万有特性universal characteristic大气压力air pressure真空度degree of vacuum怠速idle化学平衡chemical equilibrium点火提前角ignition advance angle大气湿度atmospheric humidity废气再循环Exhaust Gas Recirculation涡流vortex稀薄燃烧lean combustion气门重叠角valve overlap angle电子控制汽油喷射Electronic Fuel Injection 压力传感器Sensor空气流量计air flow meter紊流发生罐turbulence generating pot液体代用燃料liquid fuel substitute气体代用燃料gas fuel substitute后处理装置after treatment device三元催化反应器Three Way catalysts烟度limit of smoke消烟添加剂additive机内净化internal purification声强sound intensity声级计sound level meter消声器muffler烟度计smoke meter声压sound pressure定容取样法Constant V olume Sampling欧洲经济委员会Economic Commission for Europe欧洲经济共同体European Economic Community汽车排气净化automobile exhaust gas purification环境调节与自净能力environment adjustment and self-purification ability世界环境卫生经济合作与发展组织World Environment Health Organization for Economic Cooperation and Development汽车污染物排放标准Exhaust Standard for automobile pollution 催化净化装置catalysis and purification device活塞式内燃机piston type internal combustion engine中型客车Medium-sized passenger train发动机工作容积engine working volume四冲程内燃机four stroke internal combustion engine速度特性speed characteristic发动机外特性engine external characteristic电子控制点火系统Electronic Ignition System复合涡流控制燃烧compound vortex controlled combustion 程序化燃烧过程programmed combustion process曲轴箱强制通风系统Position Crankcase V entilatio废气涡轮增压技术exhaust turbo charging technique频带与频谱分析frequency band and spectrum analysis5※<标题十一>《汽车可靠性设计》事件event随机事件random event概率probability随机变量variant分布函数distribute function中位数median众数mode抽样samplingF检验F-test方差variance平均故障时间间隔MTTF-mean time to failure 平均维修时间间隔MTTR-mean time to repair 缺陷defect互换性interchange ability产品责任product liability可靠性控制reliability control可靠性管理reliability management耐久性durability走合break-in走合期break-in period走合距离break-in mileage环境温度ambient temperature大气压力atmospheric pressure台架试验bed test磨合试验running-in test工况behaviour。
常见汽车术语

常见汽车术语1. ABS(Anti-lock Braking System)ABS是一种防抱死制动系统,它能够在急刹车的过程中防止车轮抱死,提供更好的制动控制和稳定性。
ABS通过控制制动力的分配,使轮胎在最大限度上保持与地面的接触,从而避免车辆失去控制。
2. EBD(Electronic Brakeforce Distribution)EBD是电子制动力分配系统的缩写,它根据车辆的负荷和制动条件,智能地调整前后轮的制动力分配,使制动更加均匀和稳定,提供更好的制动效果和车辆稳定性。
3. ESP(Electronic Stability Program)ESP是电子稳定程序,也被称为车辆动态稳定控制系统。
它通过传感器监测车辆行驶状态,当检测到车辆出现不稳定情况时,通过制动系统和发动机管理系统的控制,自动调整车辆的制动力和动力输出,以保持车辆的稳定性。
4. HUD(Head-Up Display)HUD是抬头显示器,它是一种将车辆信息投射到驾驶员前方视野的设备。
驾驶员无需低头查看仪表盘,可以直接看到速度、转速、导航指令等信息,提高了驾驶的安全性和便利性。
5. TPMS(Tire Pressure Monitoring System)TPMS是胎压监测系统,它能够实时监测车辆轮胎的气压,并提醒驾驶员是否需要调整胎压。
保持适当的胎压对于车辆的操控性、燃油经济性和安全性都非常重要,TPMS可以帮助驾驶员保持合适的胎压。
6. DCT(Dual Clutch Transmission)DCT是双离合器变速器,它是一种先进的自动变速器技术。
DCT结合了手动变速器和自动变速器的优点,通过双离合器的设计,实现了快速平顺的换挡和高效的动力传输。
7. TCS(Traction Control System)TCS是牵引力控制系统,它能够通过控制车轮的旋转速度,防止车辆在加速时出现打滑现象。
TCS可以提供更好的牵引力和车辆稳定性,特别在低摩擦路面和恶劣天气条件下更为重要。
汽车专业术语大全
汽车专用术语大全汽车专用术语大全((英文注释英文注释))1、 引擎系统引擎系统(Automotive Engine System)(Automotive Engine System)(Automotive Engine System)燃烧室燃烧室(Combustion Chamber)(Combustion Chamber)(Combustion Chamber) 活塞到达上死点后其顶部与汽缸盖之间的空间,燃料即在此室燃烧。
压缩比压缩比(Compression Ratio)(Compression Ratio)(Compression Ratio) 活塞在下死点的汽缸之总容积除以活塞在上死点的总容积(燃烧室容积),所得的值就称为压缩比。
连杆连杆(Connecting Rod)(Connecting Rod)(Connecting Rod) 引擎中连接曲轴与活塞的连接杆。
冷却系统冷却系统(Cooling System)(Cooling System)(Cooling System) 可藉冷却剂的循环,将多余的热量移出引擎,以防止过热的系统。
在水冷式的引擎中,包括水套、水泵、水箱及节温器。
曲轴箱曲轴箱(Crankcase)(Crankcase)(Crankcase) 引擎下部,为曲轴运转的地方,包括汽缸体的下部和油底壳。
曲轴曲轴(Crankshaft)(Crankshaft)(Crankshaft) 引擎的主要旋转机件,装上连杆后,可承接连杆的上下(往复)运动变成循环(旋转)运动。
曲轴齿轮曲轴齿轮(Crankshaft Gear)(Crankshaft Gear)(Crankshaft Gear) 装在曲轴前端的齿轮或键齿轮,通常用来代动凸轮轴齿轮,链条或齿状皮带。
汽缸体汽缸体(Cylinder Block)(Cylinder Block)(Cylinder Block) 引擎的基本结构,引擎所有的零附件都装在该机件上,包括引擎汽缸及曲轴箱的上半部。
汽车专业名词大全
汽车专业名词大全ABS—缩短制动距离防抱死制动系统ABS(Anti-Lock Braking System)是一种防止制动过程车轮抱死(即停止滚动)的汽车主动安全装置。
当车辆遇到突然出现的障碍物时,即使是驾驶员猛踩刹车,车辆仍能控制自如。
如果某一车轮将要抱死,ABS反应将迅速降低这个车轮的制动压力,使它不至于完全停止转动。
依靠这种快速调整,保证了可能的最短制动距离,使得车辆仍能操控自如,并增强了稳定性。
在某些情况下,如在湿滑路面上还能减小制动距离。
对于未装备ABS的车辆,驾驶员可以通过点刹制动踏板人为地防止车轮抱死,但这对驾驶员的操作技能要求太高,一般人很难做到。
TCS—加速不打滑牵引力控制系统TCS(Traction Control System)是在ABS基础上的扩展。
它能防止车轮打滑,在车辆启动与加速时还保证良好的牵引性能,同时兼顾车辆的稳定性和操控性。
轮速传感器不断监视着每个车轮的运行,如果某个车轮表现出打滑的趋势,TCS会调整驱动扭矩,并且迅速干预制动系统和发动机的运行,车辆因此能够安全地启动或加速。
ESP—降低侧滑危险电子稳定程序ESP(Electronic Stability Program)是一项主动安全系统,它包含了ABS和TCS,因此能防止车轮在制动时抱死和在启动时打滑。
ESP每秒25次检测驾驶员的行驶意图和车辆的实际行驶情况,如果发现有紧急情况,它就迅速反应,并通过液压调节器调节每个车轮的制动压力,如有必要,还会干预发动机和传动系统。
ESP(Electronic Stability Program)电子稳定程序,是一项主动安全系统,ESP 整合了ABS和TCS牵引力控制系统,不仅能防止车轮在制动时抱死和启动时打滑,还能防止车辆侧滑。
此外,ESP还能以25次/秒的频率对驾驶员的行驶意图和实际行驶情况进行检测,随时待命对车辆的侧滑进行控制,保证驾乘者的行车安全。
EBD—防止甩尾电子制动力分配EBD(Electric Brake-force Distribution)也是一项主动安全装置。
汽车术语大全
标题:汽车术语大全汽车术语大全:1. 整车装备质量(kg):汽车完全装备好的质量,包括润滑油、燃料、随车工具、备胎等所有装置的质量。
2. 最大总质量(kg):汽车满载时的总质量。
3. 最大装载质量(kg):汽车在道路上行驶时的最大装载质量。
4. 最大轴载质量(kg):汽车单轴所承载的最大总质量。
与道路通过性有关5. 车长(mm):汽车长度方向两极端点间的距离。
6. 车宽(mm):汽车宽度方向两极端点间的距离。
7. 车高(mm):汽车最高点至地面间的距离。
8. 轴距(mm):汽车前轴中心至后轴中心的距离。
9. 轮距(mm):同一车轿左右轮胎胎面中心线间的距离。
10. 前悬(mm):汽车最前端至前轴中心的距离。
11. 后悬(mm):汽车最后端至后轴中心的距离。
12. 最小离地间隙(mm):汽车满载时,最低点至地面的距离。
13. 接近角(°:汽车前端突出点向前轮引的切线与地面的夹角。
14. 离去角(°:汽车后端突出点向后轮引的切线与地面的夹角。
15. 转弯半径(mm):汽车转向时,汽车外侧转向轮的中心平面在车辆支撑平面上的轨迹圆半径。
转向盘转到极限位置时的转弯半径为最小转弯半径。
16. 最高车速(km/h):汽车在平直道路上行驶时能达到的最大速度。
17. 最大爬坡度(%):汽车满载时的最大爬坡能力。
18. 平均燃料消耗量(l/100km):汽车在道路上行驶时每百公里平均燃料消耗量。
19. 车轮数和驱动轮数(n×m):车轮数以轮毂数为计量依据,n代表汽车的车轮总数,m代表驱动轮数。
发动机的基本参数汽车发动机的基本参数主要包括发动机缸数,气缸的排列形式,气门,排量最高输出功率,最大扭矩。
缸数:汽车发动机常用缸数有3、4、5、6、8缸。
排量1升以下的发动机常用3缸,2.5升一般为4缸发动机,3升左右的发动机一般为6缸,4升左右为8缸,5.5升以上用12缸发动机。
一般来说,在同等缸径下,缸数越多,排量越大,功率越高;在同等排量下,缸数越多,缸径越小,转速可以提高,从而获得较大的提高功率。
汽车基础知识大全
一、汽车术语集合1、轴距(mm):汽车前轴中心至后轴中心的距离。
2、转弯半径(mm):汽车转向时,汽车外侧转向轮的中心平面在车辆支撑平面上的轨迹圆半径。
转向盘转到极限位置时的转弯半径为最小转弯半径。
3、最大总质量(kg):汽车满载时的总质量。
4、车轮数和驱动轮数(n×m):车轮数以轮毂数为计量依据,n代表汽车的车轮总数,m代表驱动轮数。
5、最小离地间隙(mm):汽车满载时,最低点至地面的距离。
6、最大装载质量(kg):汽车在道路上行驶时的最大装载质量。
7、后悬(mm):汽车最后端至后轴中心的距离。
8、轮距(mm):同一车轿左右轮胎胎面中心线间的距离。
9、整车装备质量(kg):汽车完全装备好的质量,包括润滑油、燃料、随车工具、备胎等所有装置的质量。
10、最高车速(km/h):汽车在平直道路上行驶时能达到的最大速度。
11、车宽(mm):汽车宽度方向两极端点间的距离。
12、车高(mm):汽车最高点至地面间的距离。
13、车长(mm):汽车长度方向两极端点间的距离。
14、平均燃料消耗量(l/100km):汽车在道路上行驶时每百公里平均燃料消耗量。
15、离去角(°):汽车后端突出点向后轮引的切线与地面的夹角。
16、最大爬坡度(%):汽车满载时的最大爬坡能力。
17、前悬(mm):汽车最前端至前轴中心的距离。
18、最大轴载质量(kg):汽车单轴所承载的最大总质量。
与道路通过性有关。
19、接近角(°):汽车前端突出点向前轮引的切线与地面的夹角。
20、零公里汽车(汽车销售术语):指行驶里程为零(或里程较低,如不高于10kin)的汽车,它的出现是为了满足客户对所购车辆"绝对全新"的要求。
零公里表示汽车从生产线上下来后,还未有任何入驾驶过。
为了保证里程表的读数为零,从生产厂到各销售点,均采用大型专用汽车运输,以保证车辆全新。
二、汽车车型分类1、SUV-汽车基础知识SUV的全称是SportUtilityVehicle,中文意思是运动型多用途汽车。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
汽车常用术语1、汽车类型:the type of automobile汽车:motor vehicle,automobile载货车:truck 微型货车:mini—truck 轻型货车:light—truck中型货车:medium truck 重型货车:heavy truck 越野车:off—road vehicle 自卸车:dump truck 牵引车:towing vehicle专用汽车:special purpose vehicle 客车:bus 轿车:passenger car 微型轿车:mini-car 普通级轿车:subcompact car 中级轿车:compact car中高级轿车:intermediate car 高级轿车:limousine car2、汽车尺寸:dimension of vehicle车长:vehicle length 车宽:vehicle width 车高:vehicle height轴距:wheel space 轮距:track 前悬:front overhang后悬: rear overhang 最小离地间隙:ground clearance车轮外倾:camber angle 主销内倾:kingpin inclination 前束 toe-in3、发动机:engine发动机总体构造和工作原理:the construction and working principle汽油机gasoline engine 柴油机 diesel engine四冲程发动机four—stroke engine 单(多)缸发动机 single(multi)-cylinder engine 立(斜、卧)式发动机 vertical (inclined、horizontal) engine工作循环 working process进气(压缩、膨胀、排气)行程 suction(compression、 expansion 、exhaust) stroke 点火次序 firing order 上(下)止点 top(bottom) dead centre活塞行程 piston stroke 气缸工作容积 piston swept volume发动机排量 engine swept volume 充气系数 volumetric efficiency配气相位 valve timing 压缩比 compression ratio直接喷射 direct injection 间接喷射 indirect injection喷油压力injection pressure 电控喷射 electronic—controlled injection雾化 atomization 混合气浓度 mixtureconcentration可燃混合气 combustible mixture 空燃比 air-fuel ratio过量空气系数 excess air ratio 燃烧室 combustion chamber压燃 compression ignition 点燃 spark ignition抗暴性 antiknock quality 增压中冷 inter-cooling负荷 load 空载 no-load工况 working condition曲柄连杆机构:connecting rods and crankshaft缸盖 cylinder head 气缸 cylinder缸体 cylinder block 缸套 cylinder liner油底壳 oil pan 活塞 piston活塞环(销) piston ring(pin) 气(油)环 compression(oil control)ring连杆 connecting rod 曲柄 crank曲轴 crankshaft 飞轮 flywheel配气机构:valve gear凸轮(轴)cam(camshaft)进(排)气阀 inlet (exhaust) valve挺柱 tappet 推杆 push—rod摇臂 rocker arm燃油供给系统:fuel system柱塞(转子)式喷油泵 jerk fuel injection pump喷油器 injector 调速器 governor发动机调速系统:engine speed governing排放控制系统:emission control system发动机冷却系统:engine cooling system发动机润滑系统:engine lubrication system发动机点火系统:engine ignition system发动机起动系统:engine starting system4、汽车底盘术语离合器:clutch摩擦离合器 friction clutch(单盘single plate、双盘twin double plate、多盘multi-plate、膜片弹簧diaphragm spring、自动automatic、电磁electromagnetic)离合器操纵机构 clutch operation压盘 pressure plate分离杆 release lever 分离筒 release sleeve离合器盖 clutch cover 从动盘 clutch plate从动盘毂 clutch plate hub 分离弹簧(轴承)release spring(thrust bearing)中间压盘 center plate 压紧弹簧 pression减振弹簧 damping spring 摩擦片 plate friction lining扭转减振器 torsional damping arrangement变速器:transmission, gearbox机械式变速器 mechanical transmission自动变速器 automatic transmission主(副)变速器 basic(splitter) transmission行星齿轮变速器planetary transmission液力偶合器 fluid coupling液力变矩器torque converter万向传动装置:十字轴(非等速、等速、准等速、挠性、双联、球销、球笼)万向节 cardan (nonconstant velocity、constant velocity、near constant velocity、flexible、double cardan、ball and trunnion、rzeppa) universal joint十字轴总成 cross assembly万向节叉yoke驱动桥:driving axle断开(非断开)式驱动桥 divided (rigid) drive axle单(双)级主减速器 single (double) reduction final axle齿轮(防滑、自锁、摩擦)差速器 gear (limited—slip、self-locking、multi-disc) differential 桥壳 axle housing全浮(半浮)式半轴 full—floating (semi-floating) axle shaft转向系:steering system机械(动力)转向系manual (power) steering system 转向器 steering gear转向盘(轴、操纵机构) steering wheel (shaft、control mechanism)循环球-齿条齿扇(齿轮齿条)式转向器 recirculating ball—rack and sector (rack and pinion ) steering gear正(逆)效率 forward(reverse) efficiency行驶系:running system独立(非独立)悬架 indepenndent (rigid axle) suspension钢板(螺旋、扭杆、空气、橡胶、油气)弹簧 leaf(coil、torsion bar、air、rubber、hydro-pneumatic) spring减震器 shock absorber 横向稳定器 stabilizer anti—roll bar制动系:braking system鼓(盘)式制动器 drum (disk) brake 驻车制动装置 parking braking device制动鼓(蹄、钳)brake drum (shoe、caliper)《汽车理论》1 汽车动力性 vehicle tractive performance2 加速时间 time of acceleration3 最大爬坡度 maximum grade ability4 驱动力tractive force5 发动机的调速特性 fixed throttle characteristics6 适应性系数 adaptive coefficient7 机械效率 mechanical efficiency8 行驶阻力 resistance 9 滚动阻力 rolling resistance10 弹性迟滞 elastic slow-moving 11 滚动阻力矩 moment of rolling resistance12 滚动阻力系数 coefficient of rolling resistance13 切向反力 tangential force 14 法向反力 normal force15 空气阻力 aerodynamic resistance16 空气阻力系数 aerodynamic resistance coefficient17 坡道阻力 grade resistance 18 道路阻力 resistance of the road19 加速阻力 accelerating resistance; inertia force20 旋转质量换算系数 correction coefficient of rotating mass21 附着力 adhesive force 22 切向反作用力 tangential force 23 法向反作用力 normal force 24 附着系数 coefficient of adhesion25 后备功率 power reserve 26 发动机比功率 power/mass ratio27 燃料经济性 fuel economy 28 燃油消耗率 specific fuel consumption29 万有特性 cross sectional characteristics30 负荷特性 part throttle characteristics31 道路循环油耗 fuel economy of road test cycles32 制动性 braking performance 33 地面制动力 type—ground braking force34 制动器制动力 braking force originated from brake system35 制动减速度 braking deceleration 35 制动距离 braking distance37 同步附着系数 synchronizing adhesion coefficient38 侧倾角速度 roll velocity 39 俯仰角速度 pitch velocity40 横摆角速度 yaw velocity 41 轮胎坐标系 tire axis system42 轮胎侧偏角 side—slip-angle 43 侧偏刚度 cornering stiffness 44 回正力矩 aligning torque 45 转向特性 steering characteristics46 侧偏力 cornering force 47 横摆角速度增益 yaw velocity gain 48 临界车速 critical speed 49 特征车速 characteristic speed 50 不足转向 under steer 51 过多转向 over steer52 中性转向 neutral steer 53 静态储备系数 static margin 54 瞬态响应 transient state response 55 稳态响应 steadies state response56 汽车平顺性 ride of the automobile57 路面谱 spectrum of road surface roughness58 空间频率 spatial spectral density 59 空间频率谱 spatial spectral density60时间频率谱 spectral density 61 最小离地间隙 ground clearance62 汽车的通过性 mobility over unprepared terrain63 纵向通过角 ramp angle 64 接近角 approach angle65 离地角 departure angle 66 最小转弯直径 diameter of turning circle67 转弯通道圆 turning clearance circle 68 功率循环 circulation of power69 牵引阻力 tractive resistance 70 牵引力(功率)曲线图 tractive—power chart71 最高车速 maximum velocity 72 发动机外特性 engine characteristic at maximum opening of valve73 制动效能brake efficiency 74 转向稳定性 cornering stability 75 后轴侧滑 sideslip of rear axle 76 甩尾 trail swing77 评价指标evaluated standard 78 操纵稳定性 steering stability81 主销后倾kingpin caster 82 主销内倾kingpin inclination83 功率平衡图tractive and resistance power graph84 动力因数 dynamical factor85 制动跑偏 braking deviation from 86 制动力分配brake banlance87 制动防抱死 ABS(Anti-lock Braking System)88动力特性dynamical characteristics89 横向稳定性 stability of landscape orientation90 侧偏特性cornering characteristics91 轮胎花纹 tire pattern 92 汽车技术状况 technical condition of vehicle93 暴露极限exposure boundary 94 发动机测功器 engine dynamometer95 发动机综合试验机 motor analyze / engine analyzer96 底盘测功器 chassis dynamometer97 车轮功率平衡机 dynamic wheel balancer98 前束量尺 toe—in ganger 99 外倾测量器 camber gauge100 红外线废气分析仪 infrared rays exhaust gas analysis apparatus疲劳-降低工作效率界限 fatigue—decreased proficiency boundary舒适降低界限 decreased comfort boundary《汽车设计》绪论 introduction全球定位系统Global Position System计算机辅助设计Computer Aided Design自适应巡航控制系统Autonomous Intelligent Cruise Control电子伺辅开车Drive by wire防抱死制动系统Anti-block Brake System主动悬架Active Suspension被动悬架Passive Suspension半主动悬架 Semi—Active Suspension自动变速器 Automatic Transmission电控转向系统Electronic Control Steering通用汽车公司General Motors Company成本竞争能力Cost Competitiveness成本杀手Cost killer运动型多用途车Sport & utility vehicle概念设计Concept Design前置前驱Front—engine Front—drive前置后驱Front—engine Rear-drive后置后驱Rear—engine Rear-drive中置后驱Middle—engine Rear—drive全轮驱动Full-wheel—drive长头式Cab-behind—engine truck平头式forward control layout cab or cab forward type短头式short bonneted type轴距 wheel base轮距 wheel center distance装载量weight—carrying capacity整车整备质量weight empty总质量weight in running order轴荷分配axle load ( weight)直接档direct drive燃油经济性 fuel economy百公里油耗 fuel consumption of 100km通过性throughput capacity最小转弯半径minimum negotiable radius总体布置general arrangement纵梁frame side member or frame g irder member横梁 frame cross member离合器设计 clutch design从动盘clutch driven plate or clut ch spider膜片弹簧diaphragm spring压盘 pressure plate摩擦片clutch facing从动钢片clutch cushion disk or cush ion spring扭转减振器 torsion vibration damper or torsion damper花键毂splined hub变速器设计 transmission design中间轴式变速器countershaft transmission直齿 spur gear斜齿圆柱齿轮helical gear换档机构gear shift mechanism直齿滑动齿轮shifting slider gear啮合套shifter collar同步器synchronizer轴承 bear飞溅润滑plash oiling压力润滑full pressure oiling换档位置图 gear shifting diagram第一轴input shaft中间轴counter shaft第二轴output shaft万向节设计 universal joint柔性万向节 rubber universal joint刚性万向节 rigid cardan驱动桥drive axle主减速器final gear差速器differential车轮传动wheel driver驱动桥壳rear-axle housing整体式驱动桥壳one—piece housing主减速比final drive ratio螺旋锥齿轮 helical bevel gear双曲面齿轮 hypoid bevel gear圆柱齿轮helical spur gear蜗轮蜗杆worm—and-gear (wheel)行星齿轮planetary gear最小离地间隙minimum ground clearance of rear axl e摩擦片式差速器sure—grip differential半轴 half rear axle悬架设计suspension design弹性元件springs导向机构guider减振器absorber缓冲块bumper横向稳定杆 stabilizer钢板弹簧spring leaf螺旋弹簧spiral spring扭杆弹簧torsion bar spring橡胶弹簧rubber spring空气弹簧air spring油气弹簧oiliness spring横向摆臂式独立悬架 ndependent wheel suspension by swinging arms纵向摆臂式独立悬架independent suspension by swinging arms不等长双横臂式独立悬架 long and short arm suspension烛式悬架suspension stuck麦克弗逊式独立悬架suspension McPherson strut平衡式独立悬架stabilizator suspension主簧 mail leaf of spring副簧 helper spring制动系brake system制动器brake驱动机构drive unit制动效能braking efficiency领从蹄式制动器leading—trailing shoe brake双领蹄式制动器two leading shoe brake单向增力式制动器 half—servo brake 横向稳定杆 stabilizer bar 准双曲面齿轮hypoid gear万向节轴cardan花键 spline《随机振动》1、 Random Vibration 随机振动2、 Probability 概率3、 Statistics 统计4、 Random Process 随机过程5、 Density 密度6、 Frequency 频率7、 Discrete 离散8、 Wave 波动9、 Continuous model 连续模型10、Dynamic 动力的11、Structure 结构12、Dynamic Analysis 动力学分析13、Acceleration 加速度14、Gravitational Acceleration 重力加速度15、Definite Function 有限方程16、Excitation 激励17、Response 响应18、Discrete Model 离散模型19、Stationary 平稳的20、Nonstationary 非平稳的21、Rigid Body 刚体22、Correlation Function 相关函数23、Autocorrelation 自相关24、Spectral Density 谱密度25、Power Spectrum 功率谱26、Ergodic 各态历经的27、Temporal 短时的28、Limitation 极限29、Mean 均值30、Mean Square 均方值31、Variance 方差32、Covariance 协方差33、Variable 变量34、Constant 常数35、Single 单独的36、Filter 过滤37、Cross Correlation 互相关38、Second Order 二阶39、Lag 间隙40、Regular 规律的41、Irregular 不规则的42、Property 特性43、Performance 性能44、Ensemble 整体的45、Even 偶的46、Odd 奇的47、Independent 独立的48、Zero Mean 零均值49、Scatter 离散的50、Period 周期51、Sample 样本52、Uniform 均匀的53、Absolute 绝对值54、Phase 相位55、Circular Frequency 圆频率56、Distributed 分布的57、Dirac Delta Function 狄拉克?得尔塔函数58、Magnitude 模59、Infinite 无穷的60、Periodic 周期的61、Finite 有限的62、Restriction 约束63、Evaluation 估计64、Time Domain 时域65、Frequency Domain 频域66、Fourier Series 富里叶级数67、Fourier Integral 富里叶积分68、Piecewise 分段的69、Fourier Coefficient 富里叶系数70、Complex Number 复数值71、Complex Function 复数函数72、Real Function 实数函数73、Conjugate 共轭74、Parseval’s Formula 帕舍伐尔公式75、Amplitude 振幅76、Impulse 脉冲77、Complex Frequency 复数频域的78、Ordinate 坐标79、Singularity 奇异点80、Harmonic 谐波的81、Narrow Band 窄带82、Wind Band 宽带83、Exponent 指数84、Derivation 导数85、Joint Probability 联合概率分布86、Linear 线性的87、Superposition 重叠88、Inverse Transform 逆变换89、Single Degree of Freedom 单自由度90、Natural Frequency 自然频率91、Damp 阻尼92、Critical 临界的93、Displacement 位移94、Velocity 速度95、Unit Impulse 单位脉冲96、Momentum 动量97、Ordinary Differential Equation 常微分方程98、Complex Frequency Response Function 复频响应函数99、Algebraic Equation 代数方程100、 Peak 峰值《汽车电器设备》蓄电池accumulator电解液electrolyte电路electric circuit开关switch电流表ammeter电压表voltmeter电能electric energy化学能chemical energy电流强度current intensity脉冲电流 pulse current正极板positive plate负极板negative plate单格电池cell比重计hydrometer电极electrode电荷electric charge阳极positive electrode阴极negative electrode电路图circuit diagram电器electric equipment电压voltage电位差potential difference电源power source充电系charging system交流发电机alternator充电指示器charge indicator交流电alternating current直流电direct current二极管diode三极管triode电压调节器voltage regulator过充电overcharge转子rotor定子stator皮带轮pulley警告灯warning lamp保险丝fusible link短路short circuit电动势electro-motive force起动系starting system电磁开关magnetic switch起动机马达starter motor机械能mechanical energy飞轮flywheel电磁场electromagnetic field换向器commutator电刷brush继电器relay电枢armature小齿轮pinion电枢轴armature shaft电刷弹簧brush spring轴承bearing单向离合器overrunning clutch换档机构shift mechanism电磁线圈solenoid压缩比compression ratio飞轮齿圈flywheel ring gear电枢绕组armature windings换向器片commutator segments点火系ignition system点火开关ignition switch火花塞spark plug电容器condenser分电器distributor分电器盖distributor cap点火线圈ignition coil初级绕组primary winding次级绕组secondary winding断电器breaker电磁铁electromagnet断电器触点breaker points电火花electric spark分电器点火系统distributor ignition system 空燃比air-fuel ratio火花塞间隙air gap高压high voltage低压low voltage分火头distributor rotor高压线spark plug wire分电器凸轮distributor cam附加电阻ballast resistor点火提前spark advance离心提前centrifugal advance真空提前vacuum advance大气压atmospheric pressure照明lighting照明灯light bulb信号signal报警装置warning equipment仪表meter仪表板instrument panel指示器indicator指示板indicator board指针needle控制电路control circuit辅助设备auxiliary equipment汽油机gasoline engine柴油机diesel engine汽油泵gasoline pump电磁学electromagnetism电磁波electromagnetic wave晶体管点火系统transistorized ignition system无触点电子点火系统breakerless electronic ignition system电磁感应electromagnetic《汽车电控原理及应用》进气温度(ACT)Air Charge Temperature空气流量传感器(AFS) Air Flow Sensor叶板式空气流量计(VAM)Vane Airflow Meter绝对压力传感器(AIV) Absolute Pressure Sensor空气温度传感器(ATS) Air Temperature Sensor进气温度传感器(ITA) Intake Air Temperature Sensor热线式空气流量计(HWAMMF) Hot—Wire Air-Mass Meter Flow热膜式空气流量计(HFAMFM) hot-film air—mass flow meter卡门空气流量计(KVAFM) Karman vortex air flow meter大气压力传感器(BARO sensor) barometric pressure sensor大气压力传感器(BP) barometric pressure sensor节气门关闭位置(CTP) closed throttle position进气温度传感器(IATS) intake air temperature sensor怠速空气控制阀(IACV) idle air control valve可变进气相位(VVT)variable valve timing混合气控制(M/C) mixture control节气门体(TB) throttle body节气门位置(TP) throttle position节气门位置传感器(TPS) throttle position sensor节气门位置开关(TPS) throttle position switch节气门电子控制(ETC) electronic throttle control体积空气流量(VAF) volume air flow电控单元(ECU)electronic control unit主减速器final drive【摘要】主减速器 final drive 单级主减速器 single reduction final drive 双级主减速器 double reduction final drive 前置式双级主减速器 front mounted double reduction ..。