光纤收发器HTB-1100
ScreenBeam 1100无线显示接收器快速入门指南说明书
1100 ScreenBeam 1100 WirelessDisplayReceiverQuick Start GuideThis Quick Start Guide provides the instructions on how to install the ScreenBeam 1100 receiver, connect client devices, and setup for deployment.Before Beginning DeploymentBefore deploying ScreenBeam products, check for the latest firmware, release documentation and tech tips.z For ScreenBeam receiver’s deployment guide, firmware upgrades, and release notes, go to:https:///1100z For Miracast™ or native macOS/iOS wireless display connection tutorial, go to: https:///setupz For ScreenBeam Central Management System (CMS) software, go to: https:///cmsz For Open Source information, go to:Package Contentsz ScreenBeam 1100 receiver z Power supplyz HDMI cable z Quick Start Guide (this document)z Regulatory documentsIntroductionThe ScreenBeam 1100 allows presenters with Windows 10, macOS, iOS, or Android device to wirelessly display without requiring any apps. ScreenBeam 1100 offers a variety of secured network modes to support connection from the internal users on different subnets and external guest users.Overview of Network ModesScreenBeam 1100 supports local Wi-Fi, Wi-Fi Miracast, and wireless display over existing infrastructure network. T wo or more modes can operate concurrently to support various scenarios where both internal and guest users could simply connect and project.1100Local Wi-FiThe ScreenBeam Wi-Fi mode provides the simplest form of network for client devices to connect and project. In this mode, user needs to connect the client device Wi-Fi to the ScreenBeam Wi-Fi and then select the receiver to mirror. This mode is ideal for guest client devices that needs wireless display and or Internet access. Internet is available if the ScreenBeam receiver is connected to the existing network, wired or wireless if bridge mode is enabled. Mobile device with cellular service can access the Internet and wireless display if bridge mode is disabled.Figure 1 Client device wireless display by connecting to ScreenBeam’s local Wi-FiNote: ScreenBeam Wi-Fi is fully secured and manageable via ScreenBeam CMS with options to tune the wireless power transmission, channel and encryption type.Wi-Fi MiracastThe Wi-Fi Miracast mode allows compatible Wi-Fi Miracast devices to connect directly to ScreenBeam, even when connected to an infrastructure wireless network. Miracast is commonly available on Windows 10/8.1 and Android 4.4 (and later) devices since 2015. Users can enjoy wireless display and Internet access if the client device is already connected to Wi-Fi.Figure 2 Miracast client device wireless display by connecting to ScreenBeam’s Wi-Fi Miracast network1100Wireless Display over existing LAN ScreenBeam 1100 can be connected to the existing wireless or wired network and supports wireless display for client devices on either network. This is a common setup to support client devices that needs access to network resources. Additional port and network configurations may be required for this mode to work seamlessly.Figure 3 Client device wireless display over existing infrastructure networkScreenBeam 1100 can be connected to two different networks concurrently. This dual-network feature allows the flexibility of supporting wireless display for either staff (on internal network) or visitors (on guest network). Refer to the deployment guide for more details.Minimum RequirementsSystem RequirementsClient device from 2015 or newer with one of the following operating systems:z Windows 10 build 1709 (and later)z macOS X 10.10 (and later)z iOS 11 (and later)z Android 4.4 (and later) with MiracastNetwork RequirementsFor wireless display over the existing wireless network or LAN:z Ethernet: 100BASE-T 10/100 connection(1 Gbps is recommended)z Wireless: 802.11ac (5GHz is strongly recommended)z Multicast DNS (mDNS) support is required for iOS and macOS native screen mirroring to auto-discover ScreenBeamz Required portsz5353 (UDP) for Multicast DNS (mDNS) discoveryz7100 (TCP and UDP) for macOS, iOS andWindows 10 mirroringz7250 (TCP) for Miracast over LAN data streamz18000-18009 (TCP) for macOS and iOS AV dataNote: Additional network configuration is not required forWi-Fi Miracast enabled device to connect. Verify Group Policy and firewall settings to allow Wi-Fi Direct groups or hosted networks.1100Setup Requirementsz ScreenBeam 1100 receiverz Display with an available HDMI inputz(Optional) Touchscreen with USB touch cablez An ethernet network connection with DHCP IP or aWi-Fi routerNote: This is used for wireless display over LAN and management.z ScreenBeam wireless display appNote: Not required for Windows 10/8.1, macOS, and iOS with native screen mirroring support.Figure 4 ScreenBeam 1100 setup1. Place the receiver next to the display.2. Connect one end of the provided HDMI cable to the receiver’sHDMI port and the other end to an available HDMI port on the display.Note: For VGA connection details, refer to the ScreenBeam 1100 User Guide.3. Optional: If the display has USB HID touch capability, insertthe HID USB connector into a USB port of the ScreenBeamreceiver. (USB cable is not included)4. Connect the receiver’s power supply to the receiver’s powerport, then to an electrical outlet.5. Optional: Connect one end of the Ethernet cable to thereceiver’s Ethernet port and connect the other end to thenetwork switch with DHCP IP. (Ethernet cable is not included).Note: Refer to section B for more information on setting upa network connection.6. Turn on the display and switch to the corresponding inputconnected to the receiver.7. Wait for the Ready to Connect screen to appear on the display.1100 ScreenBeam requires network connection for various purposes, such as wireless display over LAN support and management of the receiver. ScreenBeam can be connected to the network via wired or Wi-Fi connection.Wired ConnectionIf ScreenBeam is connected to a DHCP-enabled network, the Ready to Connect screen will show the IP address assigned to the ScreenBeam.Wireless Connection or Static IP AddressThis requires additional steps to configure the receiver with the proper network credentials. Refer to Section D for instructions on how to setup the ScreenBeam receiver.Using a wired connection with DHCP IP is recommended for initial testing.This section provides the instructions on how to connect to ScreenBeam using the native screen mirroring from the most common operating systems.Refer to /setup for details and instructions for all other operating systems.Note: The web page will display the instructions based on the client-device OS. Use the links at the bottom of the web page to select OS-specific instructions.Connect Using Local Wi-Fi1. Connect the client device’s Wi-Fi to the wireless network (APSSID) as shown on the TV display. Windows 10/8.1 or Android with Miracast can skip to Connect Using Wi-Fi Miracast section.2. Enter the password for the wireless network.screenbeam is the default password.3. Select the ScreenBeam receiver name as shown on the TV display.z For Windows 10Select Connect from the Action Center by swiping from right or simultaneously pressing the Windows key and K.z For iOS or macOSConnect with from the menu bar or control center.4. Enter in the PIN if required. If the PIN code is not displayed, trythe hidden PIN 1234.5. Select duplicate or extended screen mode if prompted.6. If the display has touch functionality, Windows 10 devices cantake advantage of the touch and inking feature by selectingAllow touch…. (Refer to section F for more details.)Note: To disconnect, return to the screen mirroring menu and select mirroring off.1100Connect Using Wi-Fi Miracast1. Select the ScreenBeam receiver name as shown on theTV display.z For Windows 10Select Connect from the Action Center by swiping from right or simultaneously pressing the Windows key and K.z For AndroidSelect the Screen Mirroring option from the quick accessmenu and follow the connection instructions.2. Enter in the PIN if required. If the PIN code is not displayed, trythe hidden PIN 1234.3. Select duplicate or extended screen mode if prompted.4. If the display has touch functionality, Windows 10 devices cantake advantage of the touch and inking feature by selectingAllow touch…. (Refer to section F for more details.)Note: Some Android devices do not support PIN and will fail to connect. Refer to section D below for instructions on how to configure ScreenBeam and disable PIN enforcement. | 11Connect Using theExisting Wireless Network or LAN1. Connect the ScreenBeam receiver to a known network whereyour client device can communicate over Wi-Fi.2. Verify the receiver obtained an IP address (shown on the Readyto Connect screen).3. Connect the client device to the same network as ScreenBeamreceiver4. Select the ScreenBeam receiver name as shown on theTV display.z For Windows 10Select Connect from the Action Center by swiping from right or simultaneously pressing the Windows key and K.z For iOS or macOSConnect with from the menu bar or control center.5. Enter in the PIN if required. If the PIN code is not displayed, trythe hidden PIN 1234.6. Select duplicate or extended screen mode if prompted.7. If the display has touch functionality, Windows 10 devices cantake advantage of the touch and inking feature by selectingAllow touch…. (Refer to section F for more details.) Congratulations!The display is now enabled for wireless screen mirroring.12 | 1100 ScreenBeam 1100 can be configured by using the ScreenBeam CMS software or accessing the ScreenBeam’s local management interface (LMI).Using ScreenBeam CMS SoftwareScreenBeam Central Management System (CMS) is a highly recommended complimentary tool for multi-unit deployment, configuration and administration.1. To obtain CMS software and the CMS User Guide, go to:https:///cms.2. Refer to the CMS User Guide for setup instructions.Note: Access to the LMI is prohibited by default if ScreenBeam 1100 is connected to ScreenBeam CMS for management. This option can be changed in the receiver’s settings.Figure 5Receivers managed by ScreenBeam CMS | 13Using Local Management on ScreenBeamThe Local Management Interface can configure and update a single ScreenBeam. There are three methods to access the LMI: Method 1: ScreenBeam Local Wi-Fi Network1. Connect the client device’s Wi-Fi to the wireless network(AP SSID) as shown on the TV display.2. Enter the password for the wireless network.screenbeam is the default password.3. The Ready to Connect screen on the display will show theassigned IP address of the ScreenBeam.4. Enter the assigned IP address into the web browser of a PC orApple device.z If the receiver is not connected to an existing wireless network or LAN, its IP address is 192.168.26.1.z If the receiver is connected a network, the IP address can be identified on the Ready to Connect screen.5. The browser may give an error stating “The connection or siteis not secure or private.” Manually accept the connection asfollows:Chrome browser: click Advanced, then click Proceed.Edge/IE browser: click Details, then Go on to the webpage (not recommended).Firefox browser: click Advanced, then click Add Exception, then click Confirm Security Exception.6. When the ScreenBeam management page appears, enter theUsername Administrator and Password screenbeam (both case-sensitive).14 | 1100Method 2: Network Connection via DHCP1. Using a shielded RJ-45-terminated Cat5e or better Ethernetcable, connect the ScreenBeam Ethernet port to a DHCP-enabled network.2. The Ready to Connect screen on the display will show theassigned IP address of the ScreenBeam. Enter this address into the web browser of a PC or Apple device on the same network as the ScreenBeam.3. Follow the directions from Method 1 from Step 5 on.Method 3: Wireless P2P Direct Connection1. Using a Windows 10/8.1 device, connect the device to theScreenBeam per section B above.2. Once connected, use a web browser and enterhttps://192.168.16.1 to access the LMI.3. Follow the directions from Method 1 from Step 5 on. | 15Under the Device Configuration PageAssign new Device Name1. From the Device Name Access option, select Enable.2. Select the Device Name text box, then enter a new name(example: Conference TV).Note: Each receiver should have a unique name; this makes it easier for users to identify and connect to the correct display. Supported naming characters areA-Z, a-z, 0-9, -, _.Change the Administrator’s Password1. Select the Administrator Password text box and enter thenew password.2. Select Apply/Save button to save any changes.Under the Features PageConfigure Force PIN Pairing OptionBy default, the Force PIN Pairing option is Enabled and the PIN code is generated randomly. A unique PIN is will be generated each time a new user/device attempts to connect. To change the PIN pairing type or PIN code:1. Select either ON to force PIN or OFF to not force PIN uponconnection.2. If Force PIN Pairing is ON, select either Each connection orFirst connection only.16 | 11003. Select Random or Static for PIN code generation.4. If Static, then enter PIN of choice. Keep note of the new PIN foruser distribution.Note: For eight-digit PIN option, only the first seven digits of the PIN can be set in configuration; the eighth digit will be automatically chosen by the ScreenBeam and appended to the first seven.5. Select Apply/Save button to save any changes. Configure HDMI/VGA PortPower ManagementBy default, ScreenBeam is designed to display the Ready to Connect screen continuously. To extend display life and/or reduce power consumption:1. Select either Screen Saver or Display Off.2. Enter a desired time for setting to take effect.3. Optional: Select a Wake up mode.4. Select Apply/Save button to save any changes. | 17ScreenBeam 1100 supports wireless inking and touch with Windows 10 Miracast for collaboration using a touchscreen display. Users can project their preferred Windows 10 application and take notes on the touchscreen; the notes appear directly on the client device. System RequirementsOS: Windows 10 build version 1709 (or later)CPU: 5th Gen Intel Core i-Series 5xxx or AMD equivalent(or better)RAM: 4 GB or moreSetup Requirementsz Interactive touch display or projectorz USB Type-A to Type-B/A cable(depending on the touchscreen type)Supported Featuresz Support USB HID display, projector, or whiteboardz Up to 20-point touchz Up to four simultaneous passive pensz Up to two simultaneous active pensSupported features may require compatible touchscreen and or application. Works best with InGlass™ Technology enabled display. Refer to the online compatibility list at:https:///touch/compatibility18 | 1100Setup and Instructions1. Connect the USB Type-A end to the ScreenBeam 1100receiver’s USB port.2. Connect the USB Type-B/A end to the USB Touch input on thedisplay or projector.Note: If the display provides more than one touch output, make sure the USB Type-B/A end is connected to the same touch output as the HDMI input.3. Connect Windows 10 device to ScreenBeam 1100 (seeinstructions in section C).4. Start using the display by touching the screen. Launch an appand draw using finger or pen.Please read the deployment guide for best practices and tips before placing the ScreenBeam 1100 to the site for users.1. Unplug the power supply and HDMI cable from ScreenBeam1100 receiver.2. Move the receiver to its permanent location.Note: Access to a wired or wireless LAN connection isrequired.3. Plug the HDMI cable to the receiver and the display.4. Plug in the receiver’s power supply.5. Switch the display to the correct input and verify the Ready toConnect screen appears.6. Verify the ScreenBeam 1100 obtains a valid IP address.Note: By default, ScreenBeam shows all of the receiver’s information on screen for ease of troubleshooting. The information can be configured to be hidden from the management interface or via CMS. | 19z Wi-Fi Internet is limited when connecting to ScreenBeam local Wi-Fi unless ScreenBeam is connected to the network and bridge mode is enabled.z If ScreenBeam is connected to the existing network, some existing access points and or controllers (i.e. Meraki or Cisco) may flag it as a rogue AP and restrict the client from connecting. Consult with the network administrator to flag ScreenBeam as a friendly access point.z Windows 10 build 1803 (and earlier) do not support wireless display PIN on Miracast over LAN. The connection will fall back to establishing the Miracast over Wi-Fi Direct path. Support InformationFor FAQs, troubleshooting tips and support, visit:https://To open a ticket for support, visit:https:///ticketWebsite: This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked “Class 2”, Listed Power Adapter or DC power source marked “L.P.S.” (or “Limited Power Source”) and rated12Vdc, 3A minimum.US SKU: Model # CDS036-W120U.International SKU: Model # ATS036T-W120V.Made by ScreenBeam.PN: 0530-0838-002© 2020 All rights reserved. ScreenBeam and the ScreenBeam logo are registered trademarks owned by ScreenBeam Inc. All other names are properties of their respective owners. Specifications subject to change without notice. 0406200-v8。
光纤收发器HTB-1100使用说明
光纤收发器使用说明(HTB-1100、HTB-1100S)一．概述光纤收发器是一种用来将计算机网络的电信号转换成光信号的光电信号转换器。
HTB-1100和HTB-1100S是10/100M自适应光纤收发器，它完全符合IEEE802.310BaseT, IEEE802.3u100BaseTX,100Base-FX标准。
并已通过了信息产业部电信设备进网检测，所有技术指标全部达到了入网标准。
HTB-1100是多模光纤收发器；HTB-1100S是单模光纤收发器。
光纤收发器有1个RJ45接口和1个SC或ST 接口，分别用来连接双绞线和光纤。
光纤收发器有6个LED指示灯：POWER、FX 100、TX100、FX Link/Act、TX Link/Act、Fdx。
二．安装和初始化请按以下步骤安装netLINK系列光纤收发器：1．将光纤跳线或尾纤从光纤终端盒连接到光纤收发器。
请注意要将对方设备的发送端（TX）连到收发器的接收端（RX），将对方设备的接收端（RX）连到收发器的发送端（TX）。
2．将UTP跳线从网络设备连接到光纤收发器的RJ45接口，根据与光纤收发器对接设备的要求选用直通线或交叉线，一般与交换机等多地址网络设备连接时需用交叉线，而与服务器、工作站等单地址网络设备连接时需用直通线。
3．将电源适配器的DC插头接到光纤收发器的DC插座上，再将电源适配器的AC插头插入AC插座，此时光纤收发器的POWER灯亮，其它指示灯先按自检顺序依次闪亮，自检完成后将根据光纤收发器所检测到与之对接网络设备的状态来决定收发器的工作状态,指示灯将显示此时收发器的工作状态。
三．LED指示灯光纤收发器有6个LED指示灯，它们显示了收发器的工作状态，根据LED所示，就能判断出收发器是否工作正常和可能有什么问题，从而能帮助找出故障。
它们的作用分别如下所述：PWR：灯亮表示DC5V电源工作正常FX100：灯亮表示光纤传输速率为100MbpsFX Link/Act：灯长亮表示光纤链路连接正确；灯闪亮表示光纤中有数据在传输FDX：灯亮表示光纤以全双工方式传输数据TX100：灯亮表示双绞线传输速率为100MbpsTX Link/Act：灯长亮表示双绞线链路连接确；灯闪亮表示双绞线中有数据在传输四．光纤部分参数HTB-11001100S-251100S-401100S-60光纤接口SC/ST SC SC SC光纤类型多模单模单模单模中心波长850/1300nm1310nm1310nm1310nm传输距离2公里25公里40公里60公里最小发送功率-19.0dBm-19.0dBm-9.0dBm-5.0dBm最大发送功率-12.0dBm-9.0dBm-5.0dBm0dBm接收灵敏度<-30dBm<-32dBm<-32dBm<-36dBm允许链路损耗11.0dBm13.0dBm23.0dBm31.0dBm五.技术参数●标准:IEEE802.310BaseT,IEEE802.3u100Base-TX,100Base-FX●接口:双绞线:RJ45光纤:SC或ST●LED:PWR,FX100,FX Link/Act,FDX,TX100,TX Link/Act●传输速率:双绞线:10Mbps,100Mbps光纤:100Mbps●双工方式:全双工或半双工●双绞线:5，5E类●光纤:多模:50/125，62.5/125µm单模:8.3/125，9/125，10/125µm●电源:交流220V(100-250V)，50Hz直流：5V，1A●环境温度:0～50℃●存储温度:-20～70℃●湿度:5%～90%●体积：26×70×95mm（高×宽×长）六.装箱单HTB-1100或HTB-1100S光纤收发器1台AC220V/DC5V电源适配器1只使用说明1份注：1．光纤接口总是设置为100M全双工方式。
一光八电千兆光纤收发器参数
一光八电千兆光纤收发器参数
一光八电千兆光纤收发器是一种用于光纤通信的设备，通常用
于光纤传输网络中。
这种收发器的参数包括但不限于以下几个方面：
1. 光纤接口类型，一般来说，光纤收发器会有特定的光纤接口
类型，比如SC、LC或者FC等，这些接口类型对应不同的光纤连接
标准。
2. 传输速率，千兆光纤收发器的传输速率通常为1Gbps，也就
是千兆位每秒，这决定了其在网络中的数据传输能力。
3. 工作模式，光纤收发器可能支持全双工或者半双工模式，全
双工模式可以同时进行双向数据传输，而半双工模式则只能单向传
输或接收数据。
4. 工作距离，光纤收发器的工作距离参数表示了其支持的光纤
传输距离范围，通常以公里为单位进行标识。
5. 光纤类型，光纤收发器可能支持不同类型的光纤，比如单模
光纤或多模光纤，这取决于其用途和应用场景。
6. 光功率，收发器的光功率参数描述了其发送端和接收端的光
功率范围，这对于保证光纤传输的稳定性和可靠性非常重要。
以上是一光八电千兆光纤收发器可能涉及的一些参数，这些参
数对于选择合适的设备以及在实际应用中的配置和调试都非常重要。
希望这些信息能够帮助你更好地了解和使用光纤收发器。
重庆图海光纤网络批发城报价单
以电话垂询为准
无忧
无忧
。 一般10元没芯，点位多可以7到8块。
断点，测试一次收费300.
230 280 260
重庆图海光纤网络设备批发
刘波 18696653922 QQ:1839308696 地址：石桥铺佰腾数码广场4楼4F-C10
光纤收发器专区netlink
百兆 单模双纤收发器 百兆 多模双纤收发器 百兆 单模单纤收发器 千兆 单模双纤收发器 千兆 多模双纤收发器 千兆 单模单纤收发器 HTB-1100S-25KM HTB-1100-2KM HTB-3100A/B-25KM HTB-GS-03 HTB-GM-03 千兆单纤-20KM-A/B 对 对 对 对 对 对
立杆系列
8 25 0.8 1.1 1.4 2 110 60 130 0.3缆 8芯光缆 12芯光缆 24芯光缆 立杆 地龙，箱子 立杆 皮线光纤2心 SC-SC跳线 FC-FC
89（直径） 114的直径 白色带钢丝 电信级 电信级
承接光纤熔接工程
起步价200元，车费住宿另算。 一般10元没芯，点位多可以7 公司有OTDR测试仪器，可以寻找光纤断点，测试一次收费300.
光纤产品全系列，视频光端机 光纤收发器 重庆总代理，详细请以电话垂询为准
一年包换
三年质保
售后无忧
一年包换
大接线盒 小接线盒 FC-FC耦合器 FC-SC耦合器 SC-SC耦合器 个 个 个 个 个 40 30 1.5 1.5 1.5
三年质保
售后无忧
光缆
终端盒
个 个 米 米 米 米 米 个 米 米 条 条
迷你型视频光端机专区
一路视频带反向数据光端机 二路纯视频光端机 四路纯视频光端机 四路视频带反向数据光端机 八路纯视频光端机 八路视频带反向数据光端机 十六路纯视频光端机 十六路视频带反向数据光端机 14槽双电源收发器机架 RS1V1D RS2V RS4V ZX-4V1D RS8V RS8V1D RS16V ZX-16V1D-20F 14口收发器机架 对 对 对 对 对 对 对 对 台
光纤收发器说明书NT-1100S
产品名称: N-net 10/100M自适应以太网光纤收发器N-net 10/100M自适应以太网光纤收发器产品说明:N-net 10/100M自适应以太网光纤收发器概述NT-1100/NT-1100S 10/100M自适应以太网光纤收发器，可以将10/100Base-TX的双绞线电信号和100Base-FX的光信号进行相互转换。
它将网络的传输距离极限从铜线的100米扩展到100公里（单模光纤）。
典型应用是以太网距离互连，例如小区机房与城域网的连接。
由于具有自适应的功能，在与交换机连接时，交换机不需要任何设置。
新增防雷功能，保证了设备的安全性。
外置电源、内置电源可选交流220V、直流-48V 可选N-net 10/100M自适应以太网光纤收发器产品特性：自适应NT-1100/NT-1100S具有10/100M速率自适应，全/半双工自适应功能。
在网络升级时极大保护了原有的网络投资。
大容量缓存独有的缓存技术可以保证您的网络在数据传输及多媒体应用时表现得更为出色，缓存为2M。
N-net 10/100M自适应以太网光纤收发器性能：N-net 10/100M自适应以太网光纤收发器骨干特性符合：IEEE802.3 10Base-T标准符合：IEEE802.3U 100Base-TX/FX标准符合：IEEE802.3X 标准N-net 10/100M自适应以太网光纤收发器端口传输速率光口:100Mbps电口:10/100Mbps交叉线与直通线自动识别NT-1100/NT-1100S与交换机或服务器等设备相连时，既可以使用交叉线也可以用直通线。
TX LINK/ACT灯亮，表示链路连通正确。
N-net 10/100M自适应以太网光纤收发器双工支持NT-1100/NT-1100S支持全/半双工自适应，10/100M自适应。
N-net 10/100M自适应以太网光纤收发器网络线缆10/100Base-TX UTP 5类线100Base-FX：多模光纤50/125，62.5/125或100/140μm单模光纤8.3/125，8.7/125，9/125或10/125μmN-net 10/100M自适应以太网光纤收发器传输距离10/100Base-TX：100米100Base-FX：2公里（多模），25/40/60/100公里（单模）N-net 10/100M自适应以太网光纤收发器光接口特性：波长：1310nm（25公里、40公里、2公里）1550nm（100公里）1310nm（多模2公里）N-net 10/100M自适应以太网光纤收发器LED显示：PWR：电源指示灯FX LINK/ACT：光链路连接/活动状态指示灯TX LINK/ACT：电链路连接/活动状态指示灯FX100：光口速率指示灯TX100：电口速度指示灯FDX：全、半双工指示灯N-net 10/100M自适应以太网光纤收发器端口配置：1个RJ45 10/100Base-TX端口1个SC/ST 多模/单模双工连接头N-net 10/100M自适应以太网光纤收发器电源要求：外置电源：5VDC 1A功耗：＜5W内置电源：220VAC、-48VDC功耗：＜5WN-net 10/100M自适应以太网光纤收发器环境要求：工作温度范围：0℃～60℃储存温度范围：-40℃～85℃相对湿度：5%～90%尺寸：电源外置式：26mm×71mm×94mm电源内置式：40mm×110mm×140mm以太网光纤收发器以太网光纤收发器机架说明书(使用前先阅本说明书)目录第一章10/100M光纤收发器说明书 (8)简介 (8)包装清单 (10)安装 (10)指示灯的说明: (11)光传输特性: (12)单纤双向光传输特性: (12)主要特性 (12)技术参数 (12)外型尺寸 (13)DIP开关说明 (13)使用注意事项 (13)常见故障排除 (14)第二章网管式光纤收发器用户使用指导 (14)第一章产品简介 (14)1.1产品描述 (14)1.2产品特点 (14)1.3技术参数 (14)第二章操作手册 (16)2.1前面板 (16)2.1.1指示灯 (16)2.1.2光接口 (17)2.1.3以太网接口（NODE/HUB） (17)2.2SW1设置 (17)第三章安装 (19)3.1安装及调试 (19)3.2简易故障分析及处理 (19)第三章1000M光纤收发器说明书 (19)简介: (19)包装清单 (20)安装 (20)指示灯的说明: (22)光纤参数 (22)技术参数 (22)使用注意事项 (23)第四章10/100/1000M光纤收发器说明书 (23)概述 (23)型号描述 (23)包装清单 (23)LED描述: (24)安装转换器的步骤： (24)链接到吉比特装置： (25)电缆连接参数： (25)TP-光纤技术规格： (25)第五章NT-R14/R16/R16M光纤收发器机架 (25)简介： (25)清单： (26)系统概述： (26)安装方法 (26)技术规格： (26)第六章MODEL277RS-232/RS-485/RS-422接口光纤MODEM (27)一、技术参数 (27)二、产品简介 (27)三、面板丝印图如图1 (28)四、接口说明 (28)五、指示灯说明 (28)M ODEL277RACK A型 (29)指示灯说明 (29)接口说明 (29)M ODEL277RACK B型 (30)指示灯说明 (30)接口说明 (30)第七章多电口交换型收发器 (30)简介 (30)包装清单 (32)安装 (32)指示灯的说明 (34)主要特性： (35)技术参数： (35)使用注意事项： (36)第八章光纤模式转换器 (36)G IGABIT 1000SX-1000LX多模到单模光纤介质转换器 (37)型号说明 (37)装箱单 (37)安装转换器 (37)光缆连接参数 (38)LED说明 (38)直流插孔和AC-DC适配器 (38)技术规格 (39)100SX-100LX快速以太网多模到单模光纤介质转换器 (39)概述 (39)型号说明 (40)装箱单. (40)安装转换器 (40)光缆连接参数 (40)LED说明 (41)直流插孔和AC-DC适配器 (41)技术规格 (41)第一章10/100M光纤收发器说明书简介感谢您购买N-net快速以太网光纤收发器！该收发器支持IEEE802.3U100Base-TX/FX,支持全双工或半双要参照以下订购指南选购。
netlingk HTB-3100光纤收发器
n e t-l i n k单纤双向收发器型号：-3100A100M 自适应以太网单纤双向光纤收发器，采用最新美国KENDIN 芯片，高品质单纤双向光收发一体模块（全新大厂名牌产品），性能稳定，质量优良。
适用于电信、广电、宽带网络等需要提高光纤数据流量及高性能、高可靠性的网络环境中。
1 个RJ45 电口和 1 个单纤SC 光口，实现双绞线和光纤之间的光电信号转换；只需一芯光纤就可完成一路信号的传输，较双纤方式提高光纤数据传输量一倍；符合10B a s e-T和100B a s e-T X，100B a s e-F X标准; 具有10M/100M自适应能力; 电口能自适应直通线/交叉线连接方式; 支持全双工/半双工工作模式；支持全双工流量控制和半双工背压流量控制; 支持防止广播风暴功能;支持1916 Byte 超大数据帧（可选项）；内置防雷电路，可大大减少雷电感应造成的损坏；双绞线最长100 米；单模光纤最长100 公里;有 6 个LED 指示灯：Power ，TX 100 ，TX Link/Act ，FX 100 ，FX Link/Act ，FDX/Col ；便于监测收发器的工作状态和判断故障原因；有外置、内置电源两种类型：A C100～265V/D C5V开关电源。
广州锐佳网络科技有限公司销售服务热线（TEL：，张先生QQ：），我们将为您提供详细的咨询和解决方案。
生产、代理和分销产品包括：一、综合布线产品：康普、安普、TCL、唯康、大唐电信、清华同方、百通、泛达、南京普天、江西普天、腾达二、光纤系列产品:1.光缆品牌：鸿达网络通、康迈斯COMAX、立孚LFOC、汉信、汉维、好光景、FIBERCOM、长飞Y O F C、兆比特、唯康V C O M、T C L、康普、安普A M P；2.光纤配件：光纤跳线、尾纤、束状尾纤、带状尾纤、耦合器（光纤适配器/法兰）、光纤盒/光纤配线架/O D F架/光缆交接箱、光纤接续盒、光模块；3.光纤收发器（光电转换器）/光纤收发器机架：N-NET、Net-link、D-LINK、康迈斯COMAX、立孚、汉信、汉维、好光景、FIBERSHOW、FIBERCOM、长飞、兆比特、瑞斯康达；三、交换机系列产品：华为、H3C、思科、D-L I N K四、机柜系列产品：1.品牌：金盾、图腾、柏林、三盛、各种中性机柜；2.室内外电缆配线箱、电话配线箱、宽带配线箱、光缆交接箱。
土木楼监控设备采购报价表
20、支持接入带宽≥600M，同时转发带宽≥600M；
21、支持全中文WEB GUI操作界面；
22、★单设备可管理2000个IP，2000路视频通道（投标文件中须提供第三方权威机构出具的检验报告扫描件或影印件，检验报告须体现★内容）；
23、支持H.264，H。265编码视频的预览，录像；H.265的基础上，开启智能编码后，平均码率可下降一半;
24、支持通过GB/T28181协议接入前端设备,无需使用网关服务器；
25、支持通过GB/T28181协议实现平台上下级互联,无需使用网关服务器；
26、支持对前端配用的智能警戒设备进行管理，实现警戒功能;支持发生报警时语音提示功能；
8、支持前端存储、集中存储、本地存储等存储和录像检索方式；支持服务器定时录像存储、录像回放、录像下载、视频抓拍、倍速播放、暂停控制；
9、支持电视墙切换模板配置和视频切换操作
10、支持联动报警输出、录像、声音、电视墙、电子地图、图像功能、抓拍、预置位、TTS语音等功能;
11、支持用户权限管理、设备权限设置、有效期管理等功能；
18、照度低：0.0001Lx（F=1。6，关闭帧累积，彩色模式），能基本分辨被摄目标的轮廓特征和色彩；
★19、具有音频陡升、音频陡降、音频信号丢失的音频输入异常检测功能,并能发出报警信号。（投标文件中须提供第三方权威机构出具的检验报告扫描件或影印件，检验报告须体现★内容及具有“CMA”或“CNAS"标志）; 20、可在视频图像上叠加字符，包括监控点号，监控点名称,摄像机编号、抓拍时间、车牌号码、车身颜色/车辆类型、场景编号/场景名称等信息.
光纤收发器的参数(精)
10/100M 自适应以太网光纤收发器，采用最新美国 KENDIN 芯片，高品质光收发一体模块，性能稳定，质量优良。
适用于电信、广电、宽带网络等需要高性能、高可靠性的网络及一般光纤网络环境中。
1个RJ45 电口和1个SC/ST/FC 光口，实现双绞线和光纤之间的光电信号转换。
符合 IEEE802.3 10Base-T 和 IEEE802.3u 100Base-TX ， 100Base-FX 标准。
具有 10M/100M 自适应能力。
电口能自适应直通线 / 交叉线连接方式。
支持全双工 / 半双工工作模式。
支持 IEEE802.3X 全双工流量控制和半双工背压流量控制。
支持最大 1916 Bytes 数据幀。
支持防止广播风暴功能。
内置防雷电路，可大大减少雷电感应造成的损坏。
双绞线最长 100 米 , 多模光纤最长 2 或 5 公里 ( 全双工 , 单模光纤最长 120 公里。
有 6 个 LED 指示灯： Power ， TX 100 ， TX Link/Act ， FX 100 ， FX Link/Act ， FDX/Col ；便于监测收发器的工作状态和判断故障原因。
有外置、内置电源两种类型： AC100 ～ 265V / DC5V 开关电源。
工作环境温度： 0 ～ 50 ℃。
储存环境温度： - 40 ～ 70 ℃。
收发器尺寸：电源外置式 70×26×93mm ；内置式120×30×140mm 。
光纤部分参数:型号光纤接口发射波长发射功率接收灵敏度传输距离允许损耗HTB-1100 多模ST/SC 850/1310nm -20~-12dBm -30dBm 2km 10dBmHTB-1100-5 多模ST/SC 850/1310nm -12~-6dBm -32dBm 5km 20dBmHTB-1100S-10 单模SC 1310nm -22~-14dBm -31dBm 10km 9dBmHTB-1100S-25 单模ST/SC 1310nm -14~-8dBm -32dBm 25km 18dBmHTB-1100S-40 单模SC 1310nm -8~-3dBm -33dBm 40km 25dBmHTB-1100S-60 单模SC 1310nm -3~0dBm -38dBm 60km 35dBmHTB-1100S-80 单模SC 1550nm -8~-3dBm -35dBm 80km 27dBmHTB-1100S-100单模SC 1550nm -5~0dBm -36dBm 100km 31dBmHTB-1100S-120单模SC 1550nm -3~3dBm -38dBm 120km 35dBm定货信息产品型号产品描述HTB-110010/100M 自适应以太网多模光纤收发器，光纤接口有 ST 和 SC 两种；光波长有 850 、 1310nm 两种，光纤最大距离有 2KM 和 5KM 两种。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
光纤收发器使用说明
(HTB-1100、HTB-1100S)一．概述
光纤收发器是一种用来将计算机网络的电信号转换成光信号的光电信号转换器。
HTB-1100和HTB-1100S是10/100M自适应光纤收发器，它完全符合IEEE802.310BaseT, IEEE802.3u100BaseTX,100Base-FX标准。
并已通过了信息产业部电信设备进网检测，所有技术指标全部达到了入网标准。
HTB-1100是多模光纤收发器；HTB-1100S是单模光纤收发器。
光纤收发器有1个RJ45接口和1个SC或ST 接口，分别用来连接双绞线和光纤。
光纤收发器有6个LED指示灯：POWER、FX 100、TX100、FX Link/Act、TX Link/Act、Fdx。
二．安装和初始化
请按以下步骤安装netLINK系列光纤收发器：1．将光纤跳线或尾纤从光纤终端盒连接到光纤收发器。
请注意要将对方设备的发送端（TX）连到收发器的接收端（RX），将对方设备的接收端（RX）连到收发器的发送端（TX）。
2．将UTP跳线从网络设备连接到光纤收发器的RJ45接口，根据与光纤收发器对接设备的要求选用直通线或交叉线，一般与交换机等多地址网络设备连接时需用交叉线，而与服务器、工作站等单地址网络设备连接时需用直通线。
3．将电源适配器的DC插头接到光纤收发器的DC插座上，再将电源适配器的AC插头插入
AC插座，此时光纤收发器的POWER灯亮，
其它指示灯先按自检顺序依次闪亮，自检完
成后将根据光纤收发器所检测到与之对接网
络设备的状态来决定收发器的工作状态,指
示灯将显示此时收发器的工作状态。
三．LED指示灯
光纤收发器有6个LED指示灯，它们显示了收
发器的工作状态，根据LED所示，就能判断出收发
器是否工作正常和可能有什么问题，从而能帮助找
出故障。
它们的作用分别如下所述：
PWR：灯亮表示DC5V电源工作正常
FX100：灯亮表示光纤传输速率为100Mbps
FX Link/Act：灯长亮表示光纤链路连接正确；
灯闪亮表示光纤中有数据在传输
FDX：灯亮表示光纤以全双工方式传输数据
TX100：灯亮表示双绞线传输速率为100Mbps
TX Link/Act：灯长亮表示双绞线链路连接确；
灯闪亮表示双绞线中有数据在传输
四．光纤部分参数
HTB-11001100S-251100S-401100S-60
光纤接口SC/ST SC SC SC
光纤类型多模单模单模单模
中心波长850/1300nm1310nm1310nm1310nm
传输距离2公里25公里40公里60公里
最小发送功
率
-19.0dBm-19.0dBm-9.0dBm-5.0dBm
最大发送功
率
-12.0dBm-9.0dBm-5.0dBm0dBm
接收灵敏度<-30dBm<-32dBm<-32dBm<-36dBm
允许链路损
耗
11.0dBm13.0dBm23.0dBm31.0dBm
五.技术参数
●标准:IEEE802.310BaseT,IEEE802.3u
100Base-TX,100Base-FX
●接口:双绞线:RJ45
光纤:SC或ST
●LED:PWR,FX100,FX Link/Act,
FDX,TX100,TX Link/Act
●传输速率:双绞线:10Mbps,100Mbps
光纤:100Mbps
●双工方式:全双工或半双工
●双绞线:5，5E类
●光纤:多模:50/125，62.5/125µm
单模:8.3/125，9/125，10/125µm
●电源:交流220V(100-250V)，50Hz
直流：5V，1A
●环境温度:0～50℃
●存储温度:-20～70℃
●湿度:5%～90%
●体积：26×70×95mm（高×宽×长）
六.装箱单
HTB-1100或
HTB-1100S光纤收发器1台
AC220V/DC5V电源适配器1只
使用说明1份
注：1．光纤接口总是设置为100M全双工方式。
2．双绞线接口初始化时将根据检测到对接设备的状态
来设置本身的状态，如果检测不到对方状态，则将自动设置
为100M全双工状态。
3.雷电感应导致的IC损坏不在免费保修范围内。
光纤收发器使用说明
HTB-1100
HTB-1100S。