电厂常用英语词汇
常用词汇
主厂房main power building 设备缺陷equipment defect 缺陷处理defect treatment 设备规范Specification of equipment 铭牌nameplate 接线盒terminal box 热网heating network 电网network 供货范围scope of supply 参数parameter 停机, 停运outage 皮带速度belt velocity 皮带传输belt conveyor 蒸汽参数steam condition 蒸发量generation rates 功率因素power factor 输出负荷continuous rating output 额定蒸汽流量Max. continuous rating(MCR) 额定电压rated voltage 额定电流rated current 运行工况operation condition 值班员attendant 工日man-day 工时man-hour 事故甩负荷emergency load dump 四班三倒three shift by four teams 白班day shift 长白班regular shift 小休short-time off 大休long time-off 行灯safety lamp, 手锤hand hammer, 钢丝reinforcing wire 螺丝刀screw driver 测厚仪pachometer, 电筒electric torch 卡尺Sliding caliper 撬棒crowbar 手拉葫芦hand chain block 梯子Ladder, 扳手spanner 安全帽safety helmet 手套gloves 分包商sub-contractor 承包商contractor 土建civil work 工作票work order 操作票operation order
锅炉
循环流化床（锅炉） the circulating fluidized bed boiler （CFB ）固体颗粒 soiled particles 底渣 bottom ash 循环灰 circulating ash 渣场 slag yard 磨煤机 coal pulverizer 输煤系统 coal handing system 送灰器 ash conveyer 吹灰器 soot blower 除尘器 precipitator 空气过滤器 air filter 石灰石仓 limestone silo 给煤机 coal feader 返料装置 material returning device 布风板 air distributor 风嘴 air nozzles 风帽 air cap 燃烧室 combustion chamber 旋风分离器 cyclone separator 床料 bed material 布袋除尘器 bag filter 静电除尘器 electrostatic precipitator 密相区 dense region 稀相区 dilute region 煤仓 coal bunker 炉膛 furnace 过热器 superheater 再热器 reheater 输煤机 coal transporter 煤粉锅炉 pulverized coal-fired boiler 上升管 riser 下降管 downcomer 烟囱 stack 过滤器 strainer 母管 main pipe 母线 busbar 烟道 flue 烟道挡板 chimney damper 烟窗帽 chimney hood 冷渣机 slag cooler
汽包 steam drum 流化风室 fluidized air chamber 水冷壁 water-cooled wall 引风机 induced draught fan 送风机 forced draught fan 一次风 primary air 二次风 secondary air 排水设备 drainage 排污箱 blow down tank 排污系统 blow down system 烟道净化器 flue gas purifier 联箱 header （汇集分配工质） 管束（排） tube bundle 管屏 tube platen 蛇形管 coil 吊挂管 supporting tube 鳍片管 finned tube, fin tube, gilled tube 风门 air damper 炉膛容积 furnace volume 漏风试验 air leakage test 膨胀补偿节 expansion joint 变电站 substation 避雷针 lightening rod
配电盘 distribution board 阻波器 line trap 阻尼绕组 damper winding 污油泵 Sump pump 卸油泵 Oil unloading pump 锅炉附件 (锅炉辅助设备) boiler accessories 辅助设施 auxiliary plant 烟道净化器 flue gas purifier
净热值 Net heating value =低位发热量 low point heat value 总热值 total heating value =高位发热量 high point heat value 空气干燥基水分 Air dry radicle water
空气干燥基弹筒发热量 Air dry radicle bomb container heat
收到基低位发热量Received radicle low point heat
锅炉加沙系统Boiler sand injection system
三相感应电机3-phase Induction motor
防爆Explosion-proof
循环流化床
3跟2 连接处有百叶窗(shutter ) 出来3内有旋风分离器(cyclone separator) 1、煤仓；2、炉膛；3、分离器尾部烟道；
4、返料器；
5、外置式热交换器；
6、给煤机；
7、冷渣器；8、石灰石仓；9、流化风室；
10、汽包；11、对流过热器；12、省煤器；
13、空气预热器；14、电除尘器；15、引风机；
16、烟囱；17、一次风；18、下二次风；
19、上二次风；20、石灰石风机
1. Coal bunker
2. Furnace
3. Backpass of separators
4. Material-returning device
5. External heat exchanger
6. Coal feeder
7. Slag cooler
8. Limestone silo; 9. Fluidized air chamber; 10. steam Drum;
11. convection superheater 12.Economizer; 13. Air preheater;
14. Electrostatic precipitator (ESP); 15. I.D. fan; 16. Stack
17. Primary air; 18. Lower secondary air; 19. Upper secondary air; 20. Limestone fan;
电除尘器 electrostatic precipitator(ESP)
除尘器
布袋除尘器 bag filter
稀相区 dense region
炉膛内
密相区 dilute region
1锅炉系统boiler proper system
燃烧系统Combustion system
蒸汽水系统steam＆water system
2 锅炉辅件系统 boiler auxiliary equipment system
煤和石灰石系统coal and limestone system
烟风系统fuel gas and air system
灰处理系统ash handling system
锅炉控制系统boiler control system
点火系统igniition system
3燃烧系统combustion system
炉膛旋风分离器furnace cyclone seperator
燃烧器布风板burner air distributor
煤道点火装置coal duct ignition device
风帽返料器air cap material-returning device
空气预热器air preheater
4汽水系统steam and water system
汽包低温过滤器steam drum low temperature filter
过热器高温过滤器superheater high temperature filter
再热器联箱reheater header
省煤器减温器economizer temperature reducer
下降管上升管downcomer riser
5循环流化床the circulating fluidized bed boiler（CFB）
锅炉除尘排渣系统boiler dust clean and slag extracting system 汽水系统烟风及燃烧系统steam-water system flue gas & air and combustion system 输煤系统coal handling system
一次风机
辅机（风机）二次风机auxiliary system
6煤粉炉pulverized fuel boiler
炉膛furnace
燃烧器burner
煤道coal duct
空气预热器air preheater
7汽包装置steam turbine equipment
排污装置blow down device
蒸汽清洗装置steam cleaning device
加药dosing
汽水分离器steam-water separator
8锅炉辅助设备boiler auxiliary equipment
通风设备draft equipment
给煤设备coal feeder
给水设备water feeder
运煤设备coal transporter
除尘设备precipitator
除渣设备slag disposal equipment
9通风设备draft equipment
一次风（送风）primary air （forced air）二次风secondary air
引风induced air
返料风机material returning fan
烟风道flue duct
烟囱stack
10除渣设备slag disposal equipment
除尘器precipitator
输灰机ash transporter
冷渣机slag cooler
输渣机slag transporter
11锅炉附件boiler accessories
安全门safety valve
吹灰器soot blower
控制设备control device
水位计water level indicator
热工仪表thermodynamic instrument
汽机
轴承bearing 分流器shunt 锅炉补水处理boiler make-up water
treatment
断路器circuit breaker 电路electric circuit 分流器shunt trip 电容器capacity 排气压力steam pressure at exhaust 排气消音器exhaust silencer 抽汽系统steam extraction system 主蒸汽及盘路系统main and bypass system 凝结水系统condensate water system 加热器疏水系统heater drains and vents
system
辅助系统auxiliary steam system 润滑油系lubricating oil system 水处理系统water treatment system 闭式水循closed circle cooling water system 闭式冷却塔系closed cooling Tower system 主蒸汽及再热蒸汽系统main steam and
reheat steam system 厂用及仪用压缩空气系统station and instrument air compressed air system 过热器蒸汽系superheater and steam system 主厂房内厂用水系统service water system
in main building 顶轴油系统jacking oil system 密封油系统sealing oil system 轴封油系统gland and steam sealing system 轴封凝汽器gland（steam）condenser 轴封供气阀gland sealing valve 汽机盘路系统turbine bypass system 汽水取样系统steam water sampling system 液压系统hydraulic system 液压选择阀hydraulic selector 排气消音器exhaust silencer 排气系统exhaust system 高压缸high pressure cylinder 球阀globe valve 闸阀gate valve 疏水阀drain valve 节流阀throttle valve 电磁阀Solenoid valve 截止阀stop valve 主汽门（主蒸汽截止门）main stop valve 调节门control valve 逆止门check valve 抽汽调节阀extraction control valve 主汽净化系统main steam cleaning system 挡板调节damper adjustment 自来水raw water 疏水泵drain pump 循环泵circulating pump 灰泵ash pump 胶球泵（rubber）ball pump 胶球清洗系统rubber ball cleaning system 负压negative pressure 支吊架supports and hangers 原料斗raw material bunker 膨胀补偿节expansion joint 空气压缩器air compressor 灰斗ash hooper 风门air damper 沸点boiling temperature 盘车turning gear 盘车投入turning gear start-up 振动报警vibration alarm 振动给煤器vibrating feeder 振动除灰装置oscilating-type blower unit 轴外部伸shaft extension 轴位移shaft displacement 遥控remote control
自动同步self-timing 限制器limiter 蓄压器accumulator 空气凝汽器air condenser 鼓风机air blower
真空系统vacuum system
注油器oil injector 除盐水demineralized water
滤油网oil filter 排气过滤器air vent filter 机力通风塔induced draught tower 热井hot well 机力通风冷却塔forced draught cooling tower
减温水attempting water 汽蚀cavitation 密封垫gasket 扩容器flash tank 除氧器deaerator 旁路bypass valve 汽机冲转run up
保安电源系统Emergency power supply system
保安断路器safety cutout
一主蒸汽系统
1郎肯循环
锅炉（水加热）蒸汽汽轮机（水释热）凝结器给水泵锅炉Boiler steam steam turbine condenser feed water pump boiler
2主蒸汽系统
高低压主蒸汽主汽门调门高低压缸
High pressure main steam main steam valve control valve high pressure cylinder
二循环水系统
（1.凉水塔，2.机力通风塔）induced draught tower
循环泵circulating pump
胶球泵ball pump
三闭式水冷却系统
高压给水泵工作油冷却器high pressure feed water pump service oil cooler
化学取样冷却器chemistry sampling cooler
低压省煤器再循环泵low pressure economizer recirculating pump
燃机闭式水空压机gas turbine closed water air compresser 冷却水热网循环泵冷却器heading network circulating pump cooler 系统
燃机发电机空气冷却器gas turbine generator air cooler
汽轮发电机冷却器steam turbine generator cooler
燃机润滑油冷却器gas turbine lubricating cooler
汽机润滑油冷却器steam turbine lubricating cooler
膨胀水箱除盐水补水expansion tank demineralized water feed water
闭式水泵closed water pump
滤网压差大（报警）the differential pressure is too high of filter
闭式水换热器旋转滤网closed water heat exchanger rotary strainer
循环水泵凝结器机力通风塔胶球泵：清洗脏污
四凝结水系统
热井凝结水泵杂用母管（减温水）
再循环
汽机轴封加热器
Hot well condensate pump service main pipe （attempting water）
main pipe for miscellaneous use(temprature-reduction water)
Steam turbine gland seal heater
轴封加热器出口调门给水泵高压加热器
燃煤炉低压加热器除氧加热器
water- feeding pump
outlet control valve of gland seal heater (feed pump) high pressure heater coal-fired boiler low pressure heart deaerating heater
五油系统
交流润滑油泵直流润滑油泵
润滑油系统板式换热器排烟风机
高压油泵注油器
顶轴油泵
顶轴油系统滤网
模块
机械超速
保安系统汽机胀差轴向位移
轴振瓦振
低真空低油压
Alternate lubricating oil pump direct lubricating oil pump
Lubricating oil system plate exchanger vapor extractor
High pressure oil pump oil injector
Jacking oil pump
Jacking oil system filter
Module
machine overspeed
Security system steam turbine differential expansion axial displacement
Shaft vibration watt vibration
Low vacuum pressure low oil pressure l
六辅汽系统
辅汽联箱auxiliary steam header
轴封供气联箱gland and steam sealing air supply header
辅汽联络母管auxiliary steam linking main pipe
七轴封系统：
轴封加热器gland and steam sealing heater
排气风机exhaust fan
八抽汽供热系统
供热站heat supply station
热网循环泵heating network circulating pump
热网疏水泵heating network drain pump
旋转隔板rotating diaphragm
抽气逆止门（防止倒流）extraction check valve
电气
1主要设备
发电机generator
励磁机exciter
变压器transformer
开关（断路器）switch ( circuit breaker )
隔离开关（刀闸）disconnecting switch (isolating switch) 熔断器（保险）fuse(safety fuse)
电动机motor
母线（铜排铝排）busbar
小母线：(控制回路，信号回路) secondary busbar : 控制电缆control loop cable
就地local 就地盘表local pannel 就地安装local mounted 运方
自动automatically 手动manually 自动-手动开关auto-manual switch 试验trial 解除dismantle 分闸open gate （switch off）合闸switch on 储能power storage 退出quit 退出运行outage 温度自动temperature automatic controller 电源自动加热器power source automatic heat
外部联跳（低周减载）
进线开关in-coming line switch 进线端子input terminal 启动柴油发电机start-up diesel generator 配电盘switch board 液压油泵hydraulic oil pump 防爆风机explosion-proof fan 调速油泵oil pump of speed adjustment
system 排水泵drip pump 控制箱control box 油箱净化装置oil purifier 启动准备就绪ready for start up 就地启动direct-on starting（line-start）远程启动remore boot 照明（箱）lighting 电源进线power incoming line 电源出线outwards line outgoing feeder ? 出线端outlet terminal 滤水器water strainer 胶球清洗rubber ball cleaning 汽机保安系统steam turbine security system 中间继电器intermediate relay 压差pressure difference 单侧无（电)压single none-voltage 双侧无压double side none voltage 紧急终止同期emergency stop
synchronization
启动同期工作start-up synchronization work 自动校正（同期）automatic correction 手动校准manual calibration 定子接地stator grounding 转子接地rotator grounding 定子接地保护stator ground protection
变压器
变压器投运In-service of transformer
低压厂用干式变压器（三相环氧浇注式）Low voltage auxiliary dry type transformer
(three-phase epoxy molded type)
变压器调压装置规定Specification of transformer voltage regulating device 变压器的异常运行及事故处理Accidental treatment and abnormal operation of transformer
变压器发生下列异常时允许先联系后停电If any abnormities as followings
occurred, contact is permitted at first
and then cut power
变压器轻瓦斯保护动作Action of transformer light gas
protection
变压器差动保护动作Action of transformer differential
protection
高厂变high voltage auxiliary transformer
短路阻抗short circuit impedance
绕组绝缘等级Winding insulation level
接线组别V ector group
油枕oil breather
杂物，异物sundries
变压器外壳transformer casing
1所有有关工作票应办理终结并有可投运交待，拆除临时安全措施，恢复常设安全措施，现场清洁。
All relevant work permits should be ended and instruction for putting into operation should be given; remove temporary safety precautions; reset constant safety procautions; clean the field. 2套管清洁，无裂纹，破损及放电痕迹，吸潮剂无潮解变色现象，呼吸管畅通。
Bushing shall be clean and free from phenomena as crack, damage, charging
marks, deliquescence and color changing. The breathing tube is unobstructed.
3防爆膜完整，压力释放器不动作。
Anti-explosion membrane is integrated; the pressure relief device does not act.
缩写
TSI turbine supervisory instrument 汽机监视器(汽机监视仪表) CPU central processing unit 中压处理器
DAS data acquisition system 数据采集系统
HFO heavy fuel oil 重油
LFO light fuel oil 轻油
MCR Max continuous rating 额定主蒸汽流量
Local trip 就地问题
drain oil trip 排油跳闸
BRG TEMP TRIP 轴承温度
DIFF TEMP TRIP 扩散器
LUBE OIL P LOW 润滑油油位低
EH OIL P LOW 控制油油位低
VIBRATION HIGH 振动偏高
DIFF EXPANSION diffuser 扩散器膨胀
OVERSPEED 110 超速
LP EXH TEMP TRIP 低压排气门温度跳闸
CLEAR FIRST TRIP 明确的第一次跳闸
RM(GT) reliability and maintenance 可靠性与维护性
RM (HRSG) heat recover steam generator 余热锅炉
AST SOLENOID VALVE TEST
ASP PRESSURE HIGH
RGV PRESSURE HIGH
VACUUM LOW 真空低了
DIFF EXPANSION HIGH 扩散器膨胀高了
ROTOR POSITION HIGH 转子位置高了
Local trip 就地问题
drain oil trip 排油跳闸
BRG TEMP TRIP 轴承温度
DIFF TEMP TRIP diffuser 扩散器温度跳闸
DRAIN OIL TEMP HIGH 疏油泵温度高
ETS ONE 24VDC OFF ETS Emergency Trip System 汽轮机紧急跳闸系统DEH 220VAC OFF 数字电液控制系统220V直流电关闭ETS 220VAC OFF 汽轮机紧急跳闸系统220V直流电关闭
CNTL MODE control mode 控制方式
DEH UNIT OVERVIEW Digital Electro-Hydraulic Control System 数字电液控制系统机组概观IND STEAM CONT
PE CNTR PE = Protecting Earthing 接地保护中心
OPC MODE：OPC Overspeed protection CONTROL 超速保护控制
OPC TEST MODE 超速保护控制测试类型
OPC PROHIBITED 超速保护控制禁止
FEEDBACK: 反馈
IMP PRESS LOOP
MEGAWATT LOOP
FREQ CORRECTION 频率修正
LIMITER 限制器
VALVE SEAL TEST 阀门密封测试
KKS code KKS 编码KKS是德文词“Kraftwerk-Kennzeichensystem”的缩写，意思是“电厂标识系统”
FW ＦｏｓｔｅｒＷｈｅｅｌｅｒ（ＦＷ）
电厂设备专业英语词汇讲课稿
基本专业英语一、常用运行 ON开（状态，常指信号） OFF关（状态，常指信号） OPEN 开(状态，常指阀门) CLOSE关（状态，常指阀门） START 启动 STOP 停止 ALARM报警 OPERATE 运行；操作 TRIP 跳闸 TEST 试验 INDICATION；DISPLAY指示；显示 INLET入口 OUTLET 出口 INPUT输入 OUTPUT 输出 AUTOMA TION/MANUAL(HAND) 自动/手动 AUXILIARY辅助 LOCAL就地 REMOTE摇控 PRESSURE 压力 TEMPERATURE 温度 FLOW 流量 SPEED 速度 RPM 转/分 SYSTEM 系统 BYPASS旁路 PIPE；TUBE 管道，管子 PURGE 吹扫 V ALVE 阀门 UNIT单元、机组 PRINT 打印 CURVE，LINE 曲线，线 BALANCE 平衡 INSTRUMENT AND CONTROL 仪表与控制 MODE方式，模式 SET POINT设定点 TRANSMITTIER；TRANSDUCER 变送器；传感器 CODE 代码；编码 DA TA 数据；文件；资料
STA TIC静态 DYNAMIC动态 COLD START—UP 冷态启动 WARM START—UP 温态启动 HOT START—UP 热态启动 RESET复位 SELECT选择 UNA V AIL 不允许(不能投用的) FAST 快 SLOW慢 NORMAL 正常 INCREAS 增加 DECREAS减少 二、锅炉部分 BOILER 锅炉 SUPERHEATER 过热器 REHEATER 再热器 WATERW ALL 水冷壁 DOWM COMER 下降管 HEADER 联箱、母管 STEAM DRUM 汽包 DURM PRESSURE 汽包压力 ATTEMPERATOR 减温器 SPRAY 喷水 ECONOMIZER 省煤器 ISOLATION 隔离；绝缘 CHIMNEY；STACK 烟囱 FLUE GAS 烟气 WATER 水 STEAM 蒸汽 SAFETY V ALVE 安全阀 DRAIN AND VENT 疏水和排气 Boiler Maximum Continuous Rating 锅炉最大连续出力 PRESSURE DIFFERENCE 压差 BOILER TRIP RESET 锅炉跳闸复位 OPERATE MODE SELECT 运行方式选择 MANUAL MODE 手动方式 MAIN STEAM TEMP/PRESSURE/FLOW 主汽温度/压力/流量FEED WATER FLOW 给水流量 REHEATER 再热器 manhole 人孔，检修孔 Taps 接头 pipe taps 管接头
火力发电厂英语专业词汇
火电厂英语专业词汇 acid cleaning 酸洗inter-stage leakage 级间漏汽 coal bunker 原煤斗intervation/disturbing/bump 扰动 excess air 过量空气inverter 转换开关 induced draft fan 引风机isolate 相互隔离 steam drum 汽包item 物品、元件 sub-distribution transformer 低压厂用变journal bearing 支持轴承 6kv station board 6KV公用配电屏kilo-volt 千伏 6kv unit board 6KV配电屏low pressure cylinder/casing(LP) 低压缸 A: ampere 安培large scale integrate circuit 大规模集成电路 actuator 执行机构LED 发光二极管 adapter 转接器、接头、light/ignite 点火 air circuit breaker 空气断路器linear variable differential transformer (LVDT) 线性差动变压器air dry 分析基linearization 线性化 air pre-heater 空气预热器liquid 液态 air-insulated 空气绝缘的live steam 主蒸汽 algorithms 算法load tap-changing 有载调压的 alignment 平直度log 记录、日志 alteration 改造longitudinal 纵向的 alternating current 交流电lug 吊耳 ammonia 氨major pant item 主要辅机 amplitude 幅度making current 关合电流 analogue 模拟量malfunction 误动作 Analogue to Digital conversion 模数转换mechanism 操作机构 annex 附属部分medium 媒介、介质 annular 环状的membrane panel/wall 膜式壁 annunciator 报警器micro-governor 微型调速器 anthracite 无烟煤mill 铁素体 apex 顶点millivolt 毫伏 archive buffer 文件缓冲器Mimic 模拟图 armature 电枢MMC: motor control center 电动机控制中心 as received 应用基Modulation 调节、调制 ash 灰分modulation-demodulation 调制解调 ASM 模拟子模块moisture 水分 Attemperator 减温器monitor mode 监控方式 Automatic Boiler Controls 锅炉自动控制monitor/monitor unit 监控器 automatic control system 自动控制系统monitoring 监测 autonomous 独立存在的monoxide 一氧化碳 auxiliary 辅助的motor starter 电动机启动装置 axial 轴向的motor-operated 电动操纵的 back-up 备用moving blades/ blading 动叶片 bar 条形multi-fork root 叉型叶根 bar-graph 条形图Multi Function Process(MFP) 多功能处理器 batch 成组的、成批的MV A: mega volt-ampere 兆伏安
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
电力专业常用英语词汇()
网易电力专业英语词汇(较全) 1）元件设备 三绕组变压器：three-column transformer ThrClnTrans 双绕组变压器：double-column transformer DblClmnTrans 电容器：Capacitor 并联电容器：shunt capacitor 电抗器：Reactor 母线：Busbar 输电线：TransmissionLine 发电厂：power plant 断路器：Breaker 刀闸(隔离开关)：Isolator 分接头：tap 电动机：motor 2）状态参数 有功：active power 无功：reactive power 电流：current 容量：capacity 电压：voltage 档位：tap position 有功损耗：reactive loss 无功损耗：active loss 空载损耗：no-load loss 铁损：iron loss 铜损：copper loss 空载电流：no-load current 阻抗：impedance 正序阻抗：positive sequence impedance 负序阻抗：negative sequence impedance 零序阻抗：zero sequence impedance 无功负载：reactive load 或者QLoad 有功负载: active load PLoad 遥测：YC(telemetering) 遥信：YX 励磁电流(转子电流)：magnetizing current 定子：stator 功角：power-angle
上限:upper limit 下限：lower limit 并列的：apposable 高压: high voltage 低压：low voltage 中压：middle voltage 电力系统 power system 发电机 generator 励磁 excitation 励磁器 excitor 电压 voltage 电流 current 母线 bus 变压器 transformer 升压变压器 step-up transformer 高压侧 high side 输电系统 power transmission system 输电线 transmission line 固定串联电容补偿fixed series capacitor compensation 稳定 stability 电压稳定 voltage stability 功角稳定 angle stability 暂态稳定 transient stability 电厂 power plant 能量输送 power transfer 交流 AC 装机容量 installed capacity 电网 power system 落点 drop point 开关站 switch station 双回同杆并架 double-circuit lines on the same tower 变电站 transformer substation 补偿度 degree of compensation 高抗 high voltage shunt reactor 无功补偿 reactive power compensation 故障 fault 调节 regulation 裕度 magin 三相故障 three phase fault 故障切除时间 fault clearing time 极限切除时间 critical clearing time 切机 generator triping
电厂常用英语词汇
常用词汇 主厂房main power building 设备缺陷equipment defect 缺陷处理defect treatment 设备规范Specification of equipment 铭牌nameplate 接线盒terminal box 热网heating network 电网network 供货范围scope of supply 参数parameter 停机, 停运outage 皮带速度belt velocity 皮带传输belt conveyor 蒸汽参数steam condition 蒸发量generation rates 功率因素power factor 输出负荷continuous rating output 额定蒸汽流量Max. continuous rating(MCR) 额定电压rated voltage 额定电流rated current 运行工况operation condition 值班员attendant 工日man-day 工时man-hour 事故甩负荷emergency load dump 四班三倒three shift by four teams 白班day shift 长白班regular shift 小休short-time off 大休long time-off 行灯safety lamp, 手锤hand hammer, 钢丝reinforcing wire 螺丝刀screw driver 测厚仪pachometer, 电筒electric torch 卡尺Sliding caliper 撬棒crowbar 手拉葫芦hand chain block 梯子Ladder, 扳手spanner 安全帽safety helmet 手套gloves 分包商sub-contractor 承包商contractor 土建civil work 工作票work order 操作票operation order
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
火力发电厂常用英语词汇
火力发电站常用英语技术词汇 boiler house: 锅炉房 coal conveyor 输煤装置 coal bunker: 煤仓 coal mill磨煤机 steam boiler, water boiler tube 蒸汽锅炉，管式锅炉furnace(combustion chamber): 炉膛 ( 燃烧室 ) water tube: 水管 ash pit 灰坑 superheater: 过热器 water preheater: 水预热器 air preheater: 空气预热器 gas duct(flue): 烟气管 , 烟道dust collecting plant: 集尘室 electrical precipitation plant: 电 气除尘室 induced draught fan: 引风机 chimney: 烟囱 deaerator: 除氧器 feed water tank: 供水箱 boiler feed pump: 给水泵 switchgear: 开关设备 cable tunnel: 电缆通道 cable cellar: 电缆槽 turbine room: 汽轮机室 steam turbine with alternator: 蒸汽 汽轮发电机组 economizer: 省煤器 steam drum: 汽包 surface condenser: 表面凝汽 low-pressure preheater: 低压预热器 circulating water pipe(pump): 循环 水管 control room: 控制室 electrostatic dust remover(precipitator): 静电除尘器 pulverizer 磨煤机 slag pump 灰渣泵 thermal cycle: 热力循环 (net)heat rate: （净）热耗率 Assemblie: 集合，集结，组装 comment 注释，评论 module : 模块 standby: 备用 proximity 相近，接近，亲近 .
电厂常用英文词汇
电厂常用英文词汇
1 ACTUATOR 驱动器，执行机构 2 ADAPTOR 多用插座 3 ADMINISTRATION OFFICER 行政主任 4 AIR AND FLUE GAS SYSTEM 空气及风烟系统 5 AIR-PREHEATER 空气预热器 6 AIRFLOW 空气流量 7 ALARM 报警 8 AMBIENT AIR TEMPERATURE 周围环境空气温度 9 ANALOG 模拟 10 ANALYSER 分析仪 11 ANGLE 角度 12 APPRENTICE 学徒 13 ASH 灰烬 14 ASH HANDLING 处理 15 ASH PLANT CONTROL ROOM 灰控制室 16 ASH SETTLING POND 灰沉积池 17 ASSEMBLE 装配 18 ASSISTANT ENGINEER 助理工程师 19 ATMOSPHERIC PRESSURE 大气压力 20 ATOMIZING AIR 雾化空气 21 AUTOMATIC CONTROL 自动控制 22 AUXILIARY 辅助 23 AUXILIARY STEAM 辅助蒸汽 24 AXE 斧 25 BACK PRESSURE 背压
26 BACK WASH 逆冲洗 27 BACK WASH PUMP 反冲洗泵 28 BAFFLE 隔板 29 BAG FILTER 袋式除尘器 30 BALANCE 平衡 31 BALL 球 32 BARRING GEAR (TURNING GEAR) （汽）盘车装置 33 BATTERY 蓄电池 34 BEARING 轴承 35 BEARING COOLING WATER SYSTEM 轴承冷却水系统 36 BEARING OIL (LUBRICATING OIL) 润滑油 37 BELT 皮带 38 BLACK OUT 电站全部停电 39 BLADE 叶片 40 BLOWDOWN 排污 41 BLOWDOWN TANK 排污缸 42 BLOWLAMP (BLOWTORCH) 喷焰灯 43 BOILER AND AUXILIARY 锅炉及辅机 44 BOILER COLD START 冷态启动 45 BOILER FEED PUMP 炉给水泵 46 BOILER METAL TEMPERATURE 炉金属温度 47 BOOSTER 增压器 48 BOOSTER PUMP 增压泵 49 BUCKET 斗 50 BUDGET （财政）预算 51 BUILDING 建筑物 52 BULLDOZER 推煤机 53 BUNKER 煤仓 54 BURNER 喷燃器 55 BURNING VELOCITY 燃烧速度 56 BYPASS 旁路 57 CALIPER 卡尺 58 CALIPER GAUGE 测径规 59 CANCELLED PTW (PERMIT TO WORK) 注销工作票 60 CAPACITY 容量
模具专业英语词汇
入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：spray diameter 流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot spray/cold runner 唧嘴直流: direct spray gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot spray 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 运水：water line 喉塞：line plug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug 模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar slot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 模具专业英语 推板：stripper plate 缩呵：movable core, return core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜楔：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B injection nozzle 射出喷嘴 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin
电厂专业英语词汇
火电厂英语专业词汇 acid cleaning 酸洗interstage leakage 级间漏汽 coal bunker 原煤斗intervetion/disturbing/bump 扰动 excess air 过量空气inverter 转换开关 induced draft fan 引风机isolate 相互隔离 steam drum 汽包item 物品、元件 sub-distribution transformer 低压厂用变journal bearing 支持轴承 6kv station board 6KV公用配电屏kilo-volt 千伏 6kv unit board 6KV配电屏low pressure cylinder/casing(LP) 低压缸A: ampere 安培large scale integrate circuit 大规模集成电路actuator 执行机构LED 发光二极管 adapter 转接器、接头、light/ignite 点火 air circuit breaker 空气断路器linear variable differential transformer (LVDT) 线性差动变压器 air dry 分析基linearization 线性化 air preheater 空气预热器liquid 液态 air-insulated 空气绝缘的live steam 主蒸汽 algorithms 算法load tap-changing 有载调压的 alignment 平直度log 记录、日志 alteration 改造longitudinal 纵向的 alternating current 交流电lug 吊耳 ammonia 氨major pant item 主要辅机 amplitude 幅度making current 关合电流 analogue 模拟量malfunction 误动作 Analogue to Digital conversion 模数转换mechanism 操作机构annex 附属部分medium 媒介、介质 annular 环状的membrane panel/wall 膜式壁 annunciator 报警器microgovernor 微型调速器 anthracite 无烟煤mill 铁素体 apex 顶点millivolt 毫伏 archive buffer 文件缓冲器Mimic 模拟图 armature 电枢MMC: motor control center 电动机控制中心 as received 应用基Modulation 调节、调制 ash 灰分modulation-demodulation 调制解调 ASM 模拟子模块moisture 水分 Attemperator 减温器monitor mode 监控方式 Automatic Boiler Controls 锅炉自动控制monitor/monitor unit 监控器
模具专业的英语词汇大全
模具专业的英语词汇大全 一、模具专业英语 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock
电力系统常用英文词汇
电力专业英语词汇(较全) 1、元件设备三绕组变压器three-column transformer ThrClnTrans 双绕组变压器double-column transformer DblClmnTrans 电容器Capacitor 并联电容器shunt capacitor 电抗器Reactor 母线Busbar 输电线TransmissionLine 发电厂power plant 断路器Breaker 刀闸(隔离开关)Isolator 分接头tap 电动机motor 2状态参数有功active power 无功reactive power 电流current 容量capacity 电压voltage 档位tap position 有功损耗reactive loss 无功损耗active loss 空载损耗no-load loss
铁损iron loss 铜损copper loss 空载电流no-load current 阻抗impedance 正序阻抗positive sequence impedance 负序阻抗negative sequence impedance 零序阻抗zero sequence impedance 无功负载reactive load 或者QLoad 有功负载: active load PLoad 遥测YC(telemetering) 遥信YX 励磁电流(转子电流)magnetizing current 定子stator 功角power-angle 上限:upper limit 下限lower limit 并列的apposable 高压: high voltage 低压low voltage 中压middle voltage 电力系统power system 发电机generator 励磁excitation 励磁器excitor
模具常用英文词汇
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
电力工程专业英语词汇.doc
（除尘器）振打装置Rap device （电子）板、卡card （输电）干线、通风道Trunk Bms 看门狗， bms 监视器Bms watchdog Q 线Q-line U 形螺栓U-bolt X 射线X-ray Y－△接法Wye-delta Y 形接法Wye 安规Emergency decree 安培Ampere 安培右手定则Thumb rule 安全Safety 安全措施Safety measure 安全带、保险带Lifebelt 安全的、可靠的、稳定的Safe 安全电压Safe potential 安全阀、减压阀Relieve valve 安全阀、突开阀Pop valve 安全规程Safety rules 安全帽Safety cap 安全线Escape valve 安全线Safety valve 安装Install 安装，组装assemble 安装、调整、建立Set up 安装、固定Mount 安装、装配、调整Rig 氨水箱Ammonia tank 按钮button 按钮Push button 巴，条杆Bar 白色White 百分比Percentage 百分数Percent PCT 百万分率Part per million PPM 摆动Tilting 扳手Spanner 班，组，队，大队brigade 班、组Gang 搬运机、载波、带电粒子carrier 办公室Office 办公室、会议室Chamber 磅Pound LB 磅／平方英寸（表压力）Psig 磅 /平方英寸 (绝对压力 ) Psia 饱和Saturate 饱和条件、饱和状态Saturate condition 饱和蒸汽Saturated steam SAT STM 保持Hold 保护Protection PROT 保险盒Fuse holder 保险丝、熔断器Fuse 报警Alarm 报警Warning 爆炸Explosion 备件Reserve parts 备件、备品Spare parts 备件、替换零件Replacement parts 备用、待机Standby 备用的Reserved 备用的、空余的Spare 背后，反向的Back 背压Back pressure 泵Pump Proportional/ integral / 比例／积分／微分 derivative PID 比率Ratio 比重Specific weight 闭环Closed-loop 闭式冷却水Closed cooling water 闭锁、密封舱、固定Lock 闭锁信号Blocking signal 壁面温度Wall temp 壁式再热器Radiator wall rh 避雷器Arrester 避雷器Lightning arrestor 避免 ,回避Avoid 编辑Edit 变电站、子站Substation 变送器Transmitter XMITEER 变速箱Gear shift housing 变压器Transformer XFORMER 标称出力、额定出力Nominal rating 标称的、额定的Nominal 标高Elevation ELEV 标号、标签Label 标记、注册Sign 标志Token 标准Standard 表格Tab 表格、纸张Sheet 表面的Surface 并联电抗器Shunt reactor 波纹管、膜盒Sylphon 剥线钳Wire stripper
模具专业英语词汇
Injection Mold Technical Terms （一）模具专业基本用词Professional Terms 塑料—plastic, resin 样件—sample 钢料—steel 注塑机—injection machine, press 产品—part, product, moulding 模具—mold, mould, tool A 简易模（样板模）—prototype mold B 量产用模具—production mold 三维造型（数模）—3D model, 3D data 二维产品图—2D part drawing 设计—design 制造—manufacture, build up, construction 检验—check, inspection 测量—measure, inspection 修改—change, modify, correction 工程更改—engineer change 质量—quality 数量—quantity 基准—datum, reference 牛角入水-rads gate （二）如何解析2D 产品图How to read 2D part drawing 产品几何Geometry 1．点—point 2．线（边）—line, edge 3．面face A 侧面—side B 表面—surface C 外观面—appearance surface 4．壁厚—wall thickness, stock thickness 5．加强筋（骨位）—rib 6．孔—hole 7．细长的槽—slot 8．柱位—boss 9．角—corner A 圆角—fillet B 倒角—chamfer C 尖角—sharp corner 10．斜度—angle, taper 11. 凹槽—recess , groove 分模信息Splitting 分型线—parting line (P/L), splitting line 主分模方向—main direction, line of draw 浇口设定—gating 产品标识Part Identification 产品名称—part name (P/N) 产品编号+版本号—part number + revision (Rev.)
模具专业英语词汇.doc
模具专业英语词汇 landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具 duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模