常用数控机床维修中英文对照
数控机床设备资料中英文对照
数控机床设备资料中英文对照一：说明书名次解释：lubrication hole[机]润滑孔; [机]滑油孔; 加油孔; [机]注润滑油孔Pressure Lubrication[机]压力润滑; 强制润滑; [机]加压润滑lubrication device润滑装置; 润滑油; 润滑装配AUTO LUBE 自动润滑Spindle motor 主轴马达Hydraulic pump motor 油压马达Auto Cross feed motor 前后马达High Pressure Through Coolant刀具高压冷却系统once-through coolant system一次流过冷却系统Coolant through spindle油水分离机sp. through coolant主轴通过冷却液through coolant通过冷却剂coolant jet冷却剂喷嘴flood coolant motor洪水冷却电机base coolant/gun motor基地冷却剂/枪电动机mist collect motor雾收集电动机Coolant motor (for tools/chips) 切削水马达Chip conveyor motor 铁屑输送机马达ATC motor 储刀仓马达fan cooler风扇冷却器fan draught cooler冷风机fan cooler(for amp):风扇冷却器（对放大器（amplifier））containment fan cooler安全壳风机冷却器fan-draught cooler风扇冷却器fan unit 风扇设备风扇单元风扇装置panel cooling 嵌入式降温panel door 镶板门panel heating 板壁供热tool counter工具柜台MAGAZINE CW 刀库正转MAGAZINE CCW 刀库反转 ...COUNTER （计数器）TOTAL COUNTER（总计数器）Mate：配对物（伴侣）Rotation：旋转回转Caution：谨慎radiator brake：散热器制动air duster blow gun吹尘器喷枪air-blow pipe喷气管Air Blow：鼓风Overload：超载overload protection防止过载，超载防护information overload信息过载；信息超载；信息超负荷overload capacity过载容量overload operation超负荷运行，超载运行thermal overload relay热继电器；热过载继电器overload current[电]过载电流 ; 过载电流过负荷电流dis connect jumper pin in case of using sub op存保计划连接跳线针如果使用子运算（in case of using如果使用；usb op 子运算）disconnect jumper pin断开连接跳线针beta-i servo ：β-i 伺服spindle amplifer:主轴放大器manual feed delay：手动进给延迟rigid tapping ontime：刚性攻丝准时z-axis cancel：z轴取消Current Tool Number现行刀具号Reset Current Tool恢复当前工具预设servo amp module伺服放大器模块optical fiber cable：光缆、光纤光缆sheet key板键Head sheet Key头型图要点key sheet键盘纸; 转印盘纸i series servo motor：i系列伺服电动机call light：警示灯lub. motor on :润滑泵接通（lubricant润滑剂motor-on signal马达接通信号ATC forward：ATC 向前ATC reverse ：ATC反向Ball screw:滚珠丝杠Binary code :二进制DETACH:分离，脱开Follow-up ：位置跟踪Black format：程序段格式Tool post interference check：刀架碰撞检查Abnormal load detection：异常负载检测Manual handle interruption:手轮中断Ladder diagram:梯形图（阶梯，关系图）Tool counter：工具柜台Magazine：刀库Brake module：制动模块Machine side：机侧Twist pair：双绞线Main power source：主电源Wiring diagram：接线图Current：现时状态、现行状态Dual table ：双工作台Spare：备用件、预置Aux：辅助Brake on：制动器Mist ：雾状、雾Coolant tank capacity：冷却泵油箱容量Enclosure：外壳、套、附件Overload：过载Flag：标志Condition：条件Machine ready delay：机床准备延迟Encoder：编码器Etherent：以太网口Orientation：主轴定向Spindle positioning：主轴定位Fault：故障Motion：运转Dwell：停歇，保压Feed rate：进给率Interlock/start-lock:互锁/启动-锁Spindle speed arrival check：主轴速度到达检测二、常用缩写：启动start STRT停止stop ST运行run正转forward FWD反转reverse REV加速accelerate减速reduce RED低速low L中速medium M高速high H主轴方向spindle direction向前forward FWD向后backward向左left L向右 right R诊断：DGNOS信息：MSG操作员：OPER参数：PARAM目录：DIR取代：ALTER公共地线，公共线：COM三、其它常用名次注释：金属切削 metal cutting机床 machine tool金属工艺学 technology of metals 刀具 cutter摩擦 friction联结 link传动 drive/transmission轴 shaft弹性 elasticity频率特性 frequency characteristic 误差 error响应 response定位 allocation机床夹具 jig动力学 dynamic运动学 kinematic静力学 static分析力学 analyse mechanics拉伸 pulling压缩 hitting剪切 shear扭转 twist弯曲应力 bending stress强度 intensity三相交流电 three-phase AC磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor几何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance变形力 deforming force变形 deformation应力 stress硬度 rigidity热处理 heat treatment退火 anneal正火 normalizing脱碳 decarburization渗碳 carburization电路 circuit半导体元件 semiconductor element反馈 feedback发生器 generator直流电源 DC electrical source门电路 gate circuit逻辑代数 logic algebra外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀 reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向 direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动 resultant movement of feed合成切削运动 resultant movement of cutting合成切削运动方向 direction of resultant movement of cutting 切削深度 cutting depth前刀面 rake face刀尖 nose of tool前角 rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe钻削镗削 bore车削 turning磨床 grinder基准 benchmark钳工 locksmith锻 forge压模 stamping焊 weld拉床 broaching machine拉孔 broaching装配 assembling铸造 found流体动力学 fluid dynamics流体力学 fluid mechanics加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure稳定性 stability介质 medium液压驱动泵 fluid clutch液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability随机信号 random signal离散信号 discrete signal超声传感器 ultrasonic sensor 集成电路 integrate circuit 挡板 orifice plate残余应力 residual stress套筒 sleeve扭力 torsion冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计 industrial moulding design有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器 Programmable Logic Controller PLC 电火花加工 electric spark machining电火花线切割加工 electrical discharge wire - cutting 相图 phase diagram热处理 heat treatment固态相变 solid state phase changes有色金属 nonferrous metal陶瓷 ceramics合成纤维 synthetic fibre电化学腐蚀 electrochemical corrosion车架 automotive chassis悬架 suspension转向器 redirector变速器 speed changer板料冲压 sheet metal parts孔加工 spot facing machining车间 workshop工程技术人员 engineer气动夹紧 pneuma lock数学模型 mathematical model画法几何 descriptive geometry机械制图 Mechanical drawing投影 projection视图 view剖视图 pro标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求 technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear直齿锥齿轮 straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams共轭曲线 conjugate curve范成法 generation method定义域 definitional domain值域 range导数\\微分 differential coefficient求导 derivation定积分 definite integral不定积分 indefinite integral曲率 curvature偏微分 partial differential毛坯 rough游标卡尺 slide caliper千分尺 micrometer calipers攻丝 tap二阶行列式 second order determinant逆矩阵 inverse matrix线性方程组 linear equations概率 probability随机变量 random variable排列组合 permutation and combination气体状态方程 equation of state of gas动能 kinetic energy势能 potential energy机械能守恒 conservation of mechanical energy 动量 momentum桁架 truss轴线 axes余子式 cofactor逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构 fluid drive mechanism机械零件 mechanical parts淬火冷却 quench淬火 hardening回火 tempering调质 hardening and tempering磨粒 abrasive grain结合剂 bonding agent砂轮 grinding wheel。
机床行业术语中英文对照，一人一份！
机床⾏业术语中英⽂对照，⼀⼈⼀份！⼯艺、轴引领机械前沿、机械视频，汽车、加⼯技术、3D打印、⾃动化、机器⼈、⽣产打印、⾃动化、机器⼈、⽣产⼯艺、轴承、模具、机床、钣⾦等⾏业前沿在这⾥等你搞数控加⼯，有时候了解学习国外技术或者产品时，免不了要与英⽂打交道。
往往很多常见的设备或者产品，明明很熟悉，就是拿不准英⽂的正确叫法，今天就为⼤家分享数控加⼯中常见的设备中英⽂对照。
先看⼏个常见的nc milling 数控铣床nc turning 数控车床nc grinding 数控磨床turning center 车削中⼼（1）：按英⽂字母排序3-Jaws indexing spacers 三⽖、分割⼯具头A.T.C.system 加⼯中⼼机⼑库Boring heads 搪孔头Boring machines 镗床Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰⼝铁Casting,malleable iron 可锻铸铁Casting,steel 铸钢Chamfer machines 倒⾓机Clamping/holding systems 夹具/⽀持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电⽕花线切削机CNC electric discharge machines 电脑数控电⽕花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC⼑杆CNC wire-cutting machines 电脑数控线切削机Coolers 冷却机Cutters ⼑具Diamond cutters 钻⽯⼑具Die casting dies 压铸冲模Die casting machines 压铸机Disposable toolholder bits 舍弃式⼑头Drilling machines 钻床Drilling machines bench 钻床⼯作台Drilling machines,high-speed ⾼速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical ⽴式钻床drills 钻头Electric discharge machines(EDM) 电⽕花机Electric power tools 电动⼑具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Fixture 夹具Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Grinder bench 磨床⼯作台Grinders,thread 螺纹磨床Grinders,tools & cutters ⼯具磨床Grinding machines 磨床Grinding machines,centerless ⽆⼼磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削⼯具Grinding wheels 磨轮Hand tools ⼿⼯具Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压⼯具Hydraulic power units 液压动⼒元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines,centerless ⽆⼼精研机Lathe bench 车床⼯作台Lathes,automatic ⾃动车床Lathes,heavy-duty 重型车床Lathes,high-speed ⾼速车床Lathes,turret 六⾓车床Lathes,vertical ⽴式车床Lubricants 润滑液Lubrication Systems 润滑系统Machining centers,general 通⽤加⼯中⼼Machining centers,horizontal 卧式加⼯中⼼Machining centers,horizontal & vertical 卧式及⽴式加⼯中⼼Machining centers,vertical ⽴式加⼯中⼼Machining centers,vertical double-column type ⽴式双柱加⼯中⼼Magnetic tools 磁性⼯具Milling heads 铣头Milling machines 铣床Milling machines,bed type 床⾝式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六⾓⽴式铣床Milling machines,universal 万能铣床Milling machines,vertical ⽴式铣床Milling machines,vertical & horizontal ⽴式及卧式铣床Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Planing machines 刨床Pneumatic power tools ⽓动⼯具Powder metallurgic forming machines 粉末冶⾦成型机Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack ⼸锯Saws,horizontal band 卧式带锯Saws,vertical band ⽴式带锯shafts 轴Shapers ⽜头刨床Shearing machines 剪切机Slotting machines 插床spindles 主轴Tapping machines 攻螺丝机Vises 虎钳Vises,tool-maker 精密平⼝钳Wheel dressers 砂轮修整器（2）按中⽂拼⾳字母排序铝轮冒⼝切断机 Overflow cutting machines for aluminium wheels 离⼼压⼒机 Presses,eccentric六⾓⽴式铣床 Milling machines,turret vertical六⾓车床 Lathes,turret螺栓,螺帽及螺丝 Bolts,screws & nuts螺纹磨床 Grinders,thread冷却机 Coolers冷锻 Forging,cold冷锻冲压机 Presses,cold forging⽴式双柱加⼯中⼼ Machining centers,vertical double-column type⽴式铣床 Milling machines,vertical⽴式油压拉床 Vertical hydraulic broaching machine⽴式刨床 Planing machines vertical⽴式车床 Lathes,vertical⽴式带锯 Saws,vertical band⽴式加⼯中⼼ Machining centers,vertical⽴式及卧式铣床 Milling machines,vertical & horizontal⽴式钻床 Drilling machines,vertical联轴器 Coupling连续溶解保温炉 Aluminum continuous melting & holding furnaces 连续冲模 Dies-progressive链传动 Chain drive切断机 Cutting-off machinesCNC⼑杆 CNC toolings曲柄压⼒机 presses,crank修整机 Finishing machines舍弃式⼑头 Disposable toolholder bits润滑系统 Lubrication Systems润滑液 Lubricants熔热处理炉 Heating treatment funaces三⽖、分割⼯具头 3-Jaws indexing spacers伺服冲床 Presses,servo输送链 Conveying chains⼿⼯具 Hand tools砂轮修整器 Wheel dressers蚀刻机 Etching machines外圆磨床 Grinding machines,cylindrical搪磨机 Honing machines搪孔头 Boring heads卧式铣床 Milling machines,horizontal卧式带锯 Saws,horizontal band卧式加⼯中⼼ Machining centers,horizontal卧式及⽴式加⼯中⼼ Machining centers,horizontal & vertical万能铣床 Milling machines,universal万能磨床 Grinding machines,universal镗床 Boring machines弯曲机 Bending machines弯管机 Tube bending machines通⽤加⼯中⼼ Machining centers,general铜锻 Forging,copper铣头 Milling heads铣床 Milling machines⽆⼼磨床 Grinding machines,centerless⽆⼼精研机 Lapping machines,centerless压模 Pressing dies压铸冲模 Die casting dies压铸机 Die casting machines油冷却器 Oil coolers造链机 Chain making tools造线机 Cable making tools造钉机 Nail making machines印刷电器板油压冲孔脱料系统 PCB fine piecing systems摇臂钻床 Drilling machines,radial硬(软)板(⽚)材及⾃由发泡板机组 Hard/soft and free expansion sheet making plant辗压机 Rolling machines液压元件 Hydraulic components液压冲床 Presses,hydraulic液压动⼒元件 Hydraulic power units液压⼯具 Hydraulic power tools液压回转缸 Hydraulic rotary cylindersP型PVC⾼分⼦防⽔ P type PVC waterproof rolled sheet making plant刨床 Planing machines⽜头刨床 Shapers其他铸造 Casting,other其他锻造 Forging,other模芯 Mold core模具 Molds模具维修 Mold repair模具打磨/磨纹 Mold polishing/texturing模具单元 Mold & die components模具加热器/冷却器 Mold heaters/chillers磨轮 Grinding wheels磨削⼯具 Grinding tools磨床 Grinding machines磨床⼯作台 Grinder bench平衡设备 Balancing equipment⽓油压虎钳 Pneumatic hydraulic clamps⽓动冲床 Presses,pneumatic⽓动⼯具 Pneumatic power tools轴 shafts轴承 Bearings轴承配件 Bearing fittings轴承加⼯机 Bearing processing equipment肘杆式压⼒机 Presses,knuckle joint铸铝 Casting,aluminium铸铜 Casting,copper铸造设备 Foundry equipment铸钢 Casting,steel铸灰⼝铁 Casting,gray iron织麦激光切割机 Woven-Cutting machines重⼒铸造机 Gravity casting machines重型车床 Lathes,heavy-duty主轴 spindles扳⼿ Wrenches拔丝机 Drawing machines保温炉 Heat preserving furnaces插床 Slotting machines齿轮 Gears齿轮切削机 Gear cutting machines冲压机 Stamping parts冲⼦研磨器 Punch formers超声波打磨机 Grinders,ultrasonic车床⼯作台 Lathe bench磁性⼯具 Magnetic tools传动链 Transmitted chains床⾝式铣床 Milling machines,bed type带传动 Belt drive带锯 Saws,band带锯床 Sawing machines,band电脑数控镗床 CNC boring machines电脑数控弯折机 CNC bending presses电脑数控铣床 CNC milling machines电脑数控线切削机 CNC wire-cutting machines电脑数控磨床 CNC grinding machines电脑数控车床 CNC lathes电脑数控电⽕花线切削机 CNC EDM wire-cutting machines 电脑数控电⽕花机 CNC electric discharge machines电脑数控雕刻机 CNC engraving machines电脑数控机床配件 CNC machine tool fittings电脑数控剪切机 CNC shearing machines电脑数控钻床 CNC drilling machines电动⼑具 Electric power tools电⽕花机 Electric discharge machines(EDM)雕刻机 Engraving machines⼑⽚ Blades⼑具 Cutters倒⾓机 Chamfer machines多轴钻床 Drilling machines,multi-spindle锻铝 Forging,aluminium锻压机 Presses,forging锻模 Forging dies仿形铣床 Milling machines,duplicating粉末冶⾦成型机 Powder metallurgic forming machines反射炉 Reverberatory furnaces钢锻 Forging,steel⾼速车床 Lathes,high-speed⾼速钻床 Drilling machines,high-speed管筒制造机 Pipe & tube making machines滚筒 Rollers⼯具磨床 Grinders,tools & cutters攻螺丝机 Tapping machines⼸锯 Saws,hack虎钳 Vises换模系统 Mold changing systems夹盘 Chucks夹具 Fixture夹具/⽀持系统 Clamping/holding systems剪切机 Shearing machines加⼯中⼼机⼑库 A.T.C.system激光切割 Laser cutting激光雕刻机 Engraving machines,laser激光钢板切割机 Laser cutting for SMT stensil集合管 Manifolds矫直机 Straightening machines⾦属板成型机 Sheet metal forming machines⾦属板加⼯机 Sheet metal working machines锯⽚ Blades,saw锯床 Sawing machines卷边⼯具 Crimping tools晶圆切割机 Dicing saws精密平⼝钳 Vises,tool-maker精研机 Lapping machines可锻铸铁 Casting,malleable iron快速换模系统 Quick mold change systems卡⼝ Bayonet开关及按钮 Switches & buttons钻⽯⼑具 Diamond cutters钻头 drills钻模 Jigs钻床 Drilling machines钻床⼯作台 Drilling machines bench⾃动压⼒机 Presses,transfer⾃动车床 Lathes,automatic注油机 Lubricators转台 Rotary tables你们对这个如何看，在下⾯留⾔⼤家⼀起评机械前沿： jixieqianyan机械前沿｜机械技术｜机械视频｜机械资讯。
数控机床设备资料中英文对照
数控机床设备资料中英文对照一：说明书名次解释：lubrication hole［机]润滑孔；［机］滑油孔；加油孔; ［机]注润滑油孔Pressure Lubrication［机]压力润滑; 强制润滑; [机］加压润滑lubrication device润滑装置; 润滑油; 润滑装配AUTO LUBE 自动润滑Spindle motor 主轴马达Hydraulic pump motor 油压马达Auto Cross feed motor 前后马达High Pressure Through Coolant刀具高压冷却系统once—through coolant system一次流过冷却系统Coolant through spindle油水分离机sp。
through coolant主轴通过冷却液through coolant通过冷却剂coolant jet冷却剂喷嘴flood coolant motor洪水冷却电机base coolant/gun motor基地冷却剂/枪电动机mist collect motor雾收集电动机Coolant motor (for tools/chips）切削水马达Chip conveyor motor 铁屑输送机马达ATC motor 储刀仓马达fan cooler风扇冷却器fan draught cooler冷风机fan cooler（for amp）:风扇冷却器(对放大器（amplifier））containment fan cooler安全壳风机冷却器fan—draught cooler风扇冷却器fan unit 风扇设备风扇单元风扇装置panel cooling 嵌入式降温panel door 镶板门panel heating 板壁供热tool counter工具柜台MAGAZINE CW 刀库正转MAGAZINE CCW 刀库反转 .。
COUNTER （计数器）TOTAL COUNTER（总计数器)Mate：配对物(伴侣）Rotation:旋转回转Caution:谨慎radiator brake:散热器制动air duster blow gun吹尘器喷枪air-blow pipe喷气管Air Blow：鼓风Overload：超载overload protection防止过载,超载防护information overload信息过载;信息超载；信息超负荷overload capacity过载容量overload operation超负荷运行，超载运行thermal overload relay热继电器；热过载继电器overload current［电]过载电流 ; 过载电流过负荷电流dis connect jumper pin in case of using sub op存保计划连接跳线针如果使用子运算(in case of using如果使用;usb op 子运算)disconnect jumper pin断开连接跳线针beta-i servo ：β—i 伺服spindle amplifer：主轴放大器manual feed delay：手动进给延迟rigid tapping ontime：刚性攻丝准时z—axis cancel：z轴取消Current Tool Number现行刀具号Reset Current Tool恢复当前工具预设servo amp module伺服放大器模块optical fiber cable：光缆、光纤光缆sheet key板键Head sheet Key头型图要点key sheet键盘纸；转印盘纸i series servo motor：i系列伺服电动机call light：警示灯lub。
数控机床中英文对照表
数控机床中英文对照表ABS和REL——在法那克系统中，按这两个键分别来切换当前机床的相对坐标和绝对坐标ALL——全选，程序编辑时用PRGRM——程序（program）的缩写，用于查看程序NEXT——查看程序和查看参数时，下一页OPRT——在法那克系统中，选择编辑程序时，也就是按下PRGRM后，再按这个键，才能输入程序号HOST，CONECT——这两个是在系统与外界通信时用的，我没试过，不知道什么作用HELP——查看帮助信息SHIFT——换档键，有些键有两个字符，按下这个键，用来输入顶部那个字符ALTER——程序修改键，编辑程序时用INSERT——程序插入键，编辑程序时用EOB——程序结束符，在编辑程序时，没段程序结束时，要加这个符号CAN——取消键，用来取消输入INPUT——输入键，用来输入程序或参数POS——按此键显示当前机床位置画面PROS——按此键显示当前程序画面OFFSET——按此键显示刀具偏置画面SETTING——按此键显示刀具偏置设定画面SYSTEM——按此键显示系统信息及系统状态画面GRAPH——按此键显示加工时刀具轨迹的图形画面CUSTOM——按此键显示用户宏程序画面手动数据输入(MDI)直接数字控制方法(DNC)控制器单元或机控制器单元（MCU）法拉克：ALTER 修改程序及代码INSRT 插入程序DELET 删除程序EOB 完成一句(END OF BLOCK)CAN 取消(EDIT 或MDI MODE 情况下使用)INPUT 输入程序及代码OUTPUT START 输出程序及指令OFFSET 储存刀具长度、半径补当值AUX GRAPH 显示图形PRGRM 显示程序内容ALARM 显示发生警报内容或代码POS 显示坐标DGONS PARAM 显示自我诊断及参数功能RESET 返回停止CURSOR 光标上下移动PAGE 上下翻页常见机床报警信息中英文对照T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY（NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY（+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME（轴未回零）PLEASE DRUM RETURN HOME（刀库未回零）AIRPRESSFAILURE（气压故障）UNCL TOOL FALL（松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL（夹刀失败）DRUM NOT PARKED（刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL（X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP （主变压器过热）Z AXIS NOT AT FIRST REF POSITION （Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE （主轴定向失败）TOOL DESENT OR TOOL DATA REEOR （刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK （请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE （请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL （刀库摆向换刀位失败）MG SWING OVERLOAD（刀库摆动过载）DRUM BACK PARK IS FALL （刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD （冷却泵过载）DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR （刀库位置检测开关故障）DRUM NOW NOT AT PARK （刀库未在原始位置）IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM （机械手禁动）THE SPINDLE STATU IS ERROR （主轴状态错误）ARM MOTOR OR ARM SWITCH FALL （机械手或机械手开关故障）CENTRE LUBRICATION FALL （中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE （指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE （目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT （主轴上的接近开关）THE CENTRE COOLANT IS LOWER （刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT （刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD （刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM （硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY（机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY（润滑无油）AIR PRESSURE（气压不足）COOLANT NOT READY（冷却没准备好）LUBE EMPTY（油雾油位低，润滑油位低）LUB PRESSURE LOW（润滑压力低）CONVEY VERLOAD（排屑过载）LUB OVERLOAD（润滑过载）LUBE PRESSURE LOW（油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警)NC BATTERY LOW ALARM(NC电池低报警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR MAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(气压低报警)MOTOR OVERLOAD(电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(开门)LUB PRESSURE SWITCH ERROR(油压开关错误)SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主轴负荷异常）TRANSDUCER ALARM（传感器报警）BED-HEAD LUBRICATE OFF（床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW（液压夹头压力低）HYDRAULIC TAIL PRESS LOW（液压尾座压力低）LUB 0IL LOW（油压低）TURRET CODE ERROR（转塔码错误）TURRET RUN OVERTIME（转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 轴被锁定）Y AXIS IS LOCKED（Y 轴被锁定）Z AXIS IS LOCKED（Z 轴被锁定）A AXIS IS LOCKED（A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭) SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ONHYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED（液压过滤器阻止）HYDRAULIC OIL LEVEL LOW（液压油位低）HYDRAULIC FAN QF8 OFF（液压风扇QF8关闭）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF（内冷却液QF13关闭）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW（润滑油低）DOOR OPEN（门打开）FRONT DOOR(R) OPEN（前门打开）LEFT DOOR OPEN（左门打开）LUBRICATION OIL QF23 OFF（润滑油QF23关闭）LUBRICATION PRESS LOW（润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED（门没有全部关闭）IN M06,MAG NOT READY（在M06，刀库未准备好）MAGAZINE NOT READY（刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG 关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG 机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW 探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE（参数写使能）PMC EDIT ENABLE（PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION 主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池SIEMENS常用缩略语A Output 输出ASCII American Standard Code for Information Interchange 美国信息交换标准代码AV Preparation for work 运行准备BA Operating mode 运行方式BAG Operating mode groups 运行方式组BB Ready for operation 准备好运行BCD Binary Coded Decimals 二-十进制BHG Hand-held terminal 手提终端BOF User interface 用户接口CNC Computerized Numerical Control 计算机化数字控制CP Communication Processor 通迅处理器CPU Central Processing Unit 计算机中央处理装置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央维护板，PLC 模块CTS Clear To Send 发送使能DAU Digital-Analog Converter 数模转换器DB Data Block 数据块DIN German Industrial Standards 德国工业标准DIO Data Input/Output 数据输入/输出DRF Differential Resolver Function 差分功能DRY Dry Run 空运行DSB Decoding Single Block 译码单段DSR Data Send Ready 备用输入DW Data Word 数据字E Input 输入EIA-Code Special tape code,number of holes per characters alwaysodd 特殊纸带码，每个字符的孔数为奇数EPROM Programm memory with fixed program 有固定程序的程序存储器E/R Controlled Supply and Energy Recovery Module 可控电源和能量恢复模块ETC ETC key:Extension of the softkey bar in the same menuETC 键：同级菜单扩展键FDB Product designation database 产品指定数据库FIFO First in First Out 先进先出FRA Frame module 帧频模块FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐标换算，具有零点偏置，坐标旋转，标度功能和镜向功能FRK Cutter radius compensation 铣刀半径补偿FST Feed Stop 停止进给GUD Global User Data 全体用户数据HMS High-Resolution Measuring System 高分辨率测量系统HSA Main Spindle Drive 主轴驱动HW Hardware 硬件IM Interface Module 接口模块IM-S/R Interface Module(S=send/R=receive) 接口模块，S=发送/R=接收INC Increment 步进增量ISO-Code Special tape code,number of holes per character always even特殊纸带码，每个字符的孔数为偶数K1...k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形图KV Loop-Gain Factor 增益系数KUE Transformation Ratio 传动比LCD Liquid Crystal Display 液晶显示LED Light Emitting Diode 发光二极管显示LUD Local User Data 局部用户数据MB Megabyte 兆字节MD Machine Data 机床数据MK Measuring Circuit 测量回路MDA Manual Data Automatic 手动输入，自动执行MLFB Machine-readable product designation 机器可识别的产品代号MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人机通讯：系统操作界面，用操作，编程和模拟MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多点通讯接口MSTT Machine control panel 机床控制面板NC Numerical Control 数字控制NCK Numerical Control Kernel(numerical krnel with block preparation, traversing range etc.) 数字控制核心：具有程序段预处理,运行范围等等NCU Numerical Control Unit 数控单元NURBS Non Uniform Rational B Spline 非均值有理B样条NV Zero Offset 零点偏置OEM Original Equipment Manufacturer 原设备制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 个人计算机PCMCIA Personal Computer Menory Card International Association接口协议PG Programming Device 编程器PLC Programmable Logic Control 可编程逻辑控制器PRT Program Test 程序测试RAM Random Access Memory 随机存取存储器RISC Reduced Instruction Set Computer 处理器，具有指令组小、通过能力强ROV Rapid Override 快速修调RPA R Parameters Active(NCK memoty area for R parameter numbers) R 参数有效，NCK 中用于R 参数号的存储器区RTS Request To Send(control signal from serial data interfaces)发送请求：来自串行接口的控制信号SBL Single Block 单段SBL2 Single Block Decoding 译码单段SEA Setting Data Active(memory area for setting data in NCK)设定数据有效：用于NCK 中设定数据的存储区SD Setting Data 设定数据SKP Skip Block 程序段跳跃SM Signal Module 信号模块SPF Sub Program File 子程序文件SPS Programmable Logic Controller 可编程逻辑控制器SRK Cutter Radius Compensation 刀尖半径补偿SSFK Leadscrew Error Compensation 丝杠螺距误差补偿SSI Serial Synchronous Interface 串行同步接口SW Software 软件TEA Testing Data Active(with reference to the machine data) 测试数据有效：与机床数据有关TO Tool Offset 刀具补偿TOA Tool Offset Active(memory area for tool offset) 刀具补偿有效，用于刀补的存储区TRANSMIT Transform Milling into Turning(coordinate conversion on turning machines for milling)铣床转换为车床：车床坐标换算用于铣削加工VSA Feed drive(spindle) 主轴进给驱动V Bit type PLC variable PLC变量类型：位VB Byte type PLC variablePLC变量类型：字节WKZ Tool 刀具WZ Tool 刀具WZK Tool offset 刀具补偿ZOA Zero Offset Active(memory area for zero offsets) 零点偏置有效：零点偏置存储区。
数控机床常用英语词汇
数控机床常用英语词汇T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY （NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY （+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME （轴未回零）PLEASE DRUM RETURN HOME （刀库未回零）AIRPRESS FAILURE （气压故障）UNCL TOOL FALL （松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL （夹刀失败）DRUM NOT PARKED （刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL （X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP 主变压器过热Z AXIS NOT AT FIRST REF POSITION（Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE 主轴定向失败TOOL DESENT OR TOOL DATA REEOR（刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK（请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE（请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL（刀库摆向换刀位失败）MG SWING OVERLOAD （刀库摆动过载）DRUM BACK PARK IS FALL（刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD 冷却泵过载DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR（刀库位置检测开关故障）DRUM NOW NOT AT PARK 刀库未在原始位置IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM 机械手禁动THE SPINDLE STATU IS ERROR 主轴状态错误ARM MOTOR OR ARM SWITCH FALL（机械手或机械手开关故障）CENTRE LUBRICATION FALL 中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE（指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE（目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT（主轴上的接近开关）THE CENTRE COOLANT IS LOWER（刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT（刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD（刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM（硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY （机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY （润滑无油）AIR PRESSURE （气压不足）COOLANT NOT READY （冷却没准备好）LUBE EMPTY （油雾油位低，润滑油位低）LUB PRESSURE LOW （润滑压力低）CONVEY VERLOAD （排屑过载）LUB OVERLOAD （润滑过载）LUBE PRESSURE LOW （油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警) NC BATTERY LOW ALARM (NC电池低报警) MAGAZINE MOVE LIMIT SWITCH ERROR SPINDLE TOOL UNLAMP POSITION LIMIT SWIT CH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERR ORAIR PRESSURE LOW ALARM (气压低报警) MOTOR OVERLOAD (电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERR ORDOOR IS OPENED (开门)LUB PRESSURE SWITCH ERROR (油压开关错误) SPINDLE OIL COOLANT UNIT ERROR SPINDLE LOAD ABNORMAL （主轴负荷异常）TRANSDUCER ALARM （传感器报警）BED-HEAD LUBRICATE OFF （床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW 液压夹头压力低HYDRAULIC TAIL PRESS LOW 液压尾座压力低LUB 0IL LOW （油压低）TURRET CODE ERROR （转塔码错误）TURRET RUN OVERTIME （转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOC K TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REF AFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED （X 轴被锁定）Y AXIS IS LOCKED （Y 轴被锁定）Z AXIS IS LOCKED （Z 轴被锁定）A AXIS IS LOCKED （A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ON HYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED液压过滤器阻止HYDRAULIC OIL LEVEL LOW 液压油位低HYDRAULIC FAN QF8 OFF液压风扇QF8关闭HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF （冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 M INUTESINNER COOLANT BLOCK （内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF （主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF 内冷却液QF13关闭MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW （低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW （润滑油低）DOOR OPEN （门打开）FRONT DOOR(R) OPEN （前门打开）LEFT DOOR OPEN （左门打开）LUBRICATION OIL QF23 OFF 润滑油QF23关闭LUBRICATION PRESS LOW （润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED （门没有全部关闭）IN M06,MAG NOT READY 在M06，刀库未准备好MAGAZINE NOT READY （刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETE POCKET NOT HOR./MAG NOT BCKWRD POCKET NOT VER./MAG NOT FORWRD UNCLAMP TOOL HAS NOT COMPLETED CLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ON Z NOT IN PSW2,FORBID MAG FORWARD CHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE 参数写使能PMC EDIT ENABLE （PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERR CHANGE T STOPED BECAUSE NO AIR因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOL ANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATE R 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池。
机床行业中英文对照
机床行业中英文对照下面是机床行业中常见的英文对照：- 机床行业：Machine tool industry- 机床：Machine tool- 数控机床：Computer Numerical Control (CNC) machine tool - 金属切削机床：Metal cutting machine tool- 金属加工机床：Metal processing machine tool- 金属成型机床：Metal forming machine tool- 车床：Lathe- 铣床：Milling machine- 钻床：Drilling machine- 磨床：Grinding machine- 塑料加工机床：Plastic processing machine tool- 精密机床：Precision machine tool- 自动化机床：Automated machine tool- 机床控制系统：Machine tool control system- 数控系统：Numerical control system- 机床加工能力：Machine tool processing capacity- 加工精度：Processing accuracy- 切削速度：Cutting speed- 进给速度：Feed rate- 主轴转速：Spindle speed- 工件夹紧：Workpiece clamping- 工件定位：Workpiece positioning- 刀具选择：Tool selection- 刀具更换：Tool change- 冷却液：Coolant- 刀柄：Tool holder- 加工中心：Machining center- 排屑：Chip removal- 刀具磨损：Tool wear- 折弯机：Bending machine- 冲床：Punching machine- 压力机：Press machine- 剪板机：Shearing machine- 抛光机：Polishing machine- 螺纹机床：Thread cutting machine tool - 铸造机床：Casting machine tool- 灰铁：Gray iron- 球墨铸铁：Ductile iron- 铝合金：Aluminum alloy- 不锈钢：Stainless steel- 最大加工尺寸：Maximum processing size - 机床设计：Machine tool design- 机床制造：Machine tool manufacturing - 机床市场：Machine tool market- 机床出口：Machine tool export- 机床进口：Machine tool import- 机床行业协会：Machine tool industry association。
机床术语中英文对照表
Manifolds
集合管
Milling heads
铣头
Milling machines
铣床
Milling machines,bed type
床身式铣床
Milling machines,duplicating
仿形铣床
Milling machines,horizontal
卧式铣床
Milling machines,turret vertical
铝轮冒口切断机
P type PVC waterproof rolled sheet making plant
P型PVC高分子防水
PCB fine piecing systems
印刷电器板油压冲孔脱料系统
Pipe & tube making machines
管筒制造机
Planing machines
刨床
电动刀具
Engraving machines
雕刻机
Engraving machines,laser
激光雕刻机
Etching machines
蚀刻机
Finishing machines
修整机
Fixture
夹具
Forging dies
锻模
Forging,aluminium
锻铝
Forging,cold
冷锻
自动压力机
Pressing dies
压模
Punch formers
冲子研磨器
Quick die change systems
速换模系统
Quick mold change systems
快速换模系统
Reverberatory furnaces
完整版机床用语中英文对照
完整版机床用语中英文对照Aabrasion n.磨料，研磨材料，磨蚀剂,a.磨损的,磨蚀的abrasive belt n. 砂带abrasive belt grinding n. 砂带磨削，用研磨带磨光abrasive cut-off mach ine n. 砂轮切断机abrasive dress ing wheel n. 砂轮修整轮abrasive grain n. 磨料粒度abrasive grit n. 研磨用磨料，铁粒abrasive lapp ing wheel n. 磨料研磨轮accuracy of positi on n. 位置精度accuracy to shape n. 形状精度active cutt ing edge n. 主切削刃adapter flange n. 连接器法兰盘adjointing flanks n. 共轭齿廓align n.找中（心），找正，对中，对准，找平，调直，校直，调整，调准angle millingcutter n.角铣刀an gular grin di ng n. 斜面磨削，斜磨法an gular milli ng n. 斜面铣肖Uan gular plunge grinding n. 斜向切入磨肖Uan gular turning n.斜面车肖Uarbour n.刀杆，心轴，柄轴，轴，辊轴attachment n.附件，附件机构，联结，固接，联结法automatic bar machi ne n. 棒料自动车床automatic bori ng machi ne n. 自动镗床automatic copy ing lathe n. 自动仿形车床automatic double-head milli ng mach ine n. 自动双轴铣床automatic lathe n. 自动车床automatic turret lathe n. 自动转塔车床Bbelt grinding machi ne n. 砂带磨床bench lathe n. 台式车床bevel n.斜角，斜面，倾斜，斜切，斜角规，万能角尺，圆锥的，倾斜的，斜边, 伞齿轮，锥齿轮bevel gear cutt ing mach ine n. 锥齿轮切削机床bevel gear tooth system n. 锥齿轮系，锥齿轮传动系统borehole n.镗孔，镗出的孔，钻眼boring n. 镗孔，钻孔，穿孑L boring fixture n. 镗孔夹具bori ng machi ne n. 镗床bori ng tool n. 镗刀boring, drilling and milling machine n. 镗铣床broaching machine n. 拉床，铰孔机，剥孔机broach ing tool n.拉刀broad fin ishi ng tool n. 宽刃精切刀，宽刃精车刀，宽刃光切刀CCalibrate vt.校准〔正〕，刻度，分度，检查〔验〕，定标，标定，使标准化, 使符合标准cam con tour grin der n. 凸轮仿形磨床carbide tip n.硬质合金刀片carbide turni ng tool n. 硬质合金车刀carbide-tipped tool n. 硬质合金刀具cast iron machi ning n. 铸铁加工，铸铁切削加工cen terless cyli ndrical grin der n. 无心外圆磨床ceramic cutt ing tool n.金属陶瓷刀具chamfer n.;vt.倒角，倒棱chamfered cutt ing edge n. 倒角刀刃champ v.焦急champ ing fixture n. 快换夹具champ ing jaw n. 快换卡爪chaser n.螺纹梳刀，梳刀盘，板牙chatter vi.; n.振动，振荡，震颤，刀振cherry n.;a.樱桃，鲜红的，樱桃木制的chip n.切屑，铁屑，刀片，刀头，片，薄片，芯片，基片chip breaker groove radius n. 断屑槽底半径，卷屑槽底半径chip cleara nee n. 切屑间隙chip cross-sectio nal area n. 切屑横截面面积chip curl n.螺旋形切屑chip flow n. 切屑流chip formatio n n.切屑形成chip rem oving process n. 去毛刺加工chip variable n. 切屑变量chuck n.卡盘，夹盘，卡头，〔电磁〕吸盘，vt.固定，装卡，夹紧，卡住chucker n. 卡盘车床，卡角车床circular drillling machine n. 圆工作台钻床circular path n.环路，圆轨迹circular pitch measureme nt n. 周节测量circumfere nee n.圆周，周线，周界，周围，四周，范围close-gra ined a.纟田颗粒的coeffecie nt of tool thrust n. 刀具推力系数coil chip n. 卷状切屑cold circular saw n. 冷圆锯cold saw n.冷锯colum n drilli ng mach ine n. 圆〔方〕柱立式钻床combined drill and milling cutter n. 复合钻铣床complete traverse grinding n. 横进给磨削，切入磨肖Ucomputer-controlled machine n. 计算机控制机床，数控机床contact pattern n. 靠模con ti nu ous chip n. 连续切屑con ti nu ous spiral chip n. 连续螺旋切屑con tour n.轮廓，外形，外貌，轮廓线，回路，网路，电路，等高线，等值线，轮廓等高距a.仿形的，靠模的con tour grin di ng n. 仿形磨削，成形磨削con tour milli ng n.成形铣削，外形铣削，等高走刀曲面仿形法convex milli ng attachme nt n. 凸面铣削附件convex turni ng attachme nt n. 中凸车削附件，凸面车削附件coola nt lubrica nt n. 冷却润滑剂coola nt lubrica nt emulsi on n. 冷去卩润滑乳液〔剂〕copy n.样板，仿形，靠模工作法，拷贝复制品，v.复制，模仿,抄录copy grinding n. 仿形磨床copy-mill n.仿形铣copy ing turret lathe n. 仿形转塔车床corner n.角,弯〔管〕头，弯管counterbore n.埋头孔,沉孔,锥口孔，平底扩孔钻，平底锪钻，n.;vt.扩孔，锪孔，镗孔，镗阶梯孔cran kshaft grinding machi ne n. 曲轴磨床cran kshaft turni ng lathe n. 曲轴车床creep feed grinding n. 缓进给磨肖Ucross milli ng n. 横向铣削curly chip n.卷状切屑，螺旋形切屑，切屑螺旋cut v.;n.切削〔割〕，口，片，断，断开，削减，减少，断面，剖面，相交，凹槽cut off n.切断〔开，去〕，关闭，停车，停止，断开装置，断流器，挡板，截止，截流cut teeeth n.铣齿cut-off grinding n.砂轮截断，砂轮切割cutter n.刀具，切削工具，截断器，切断器，切断机cutting n.切削，切片，切割，切屑，金属屑，截槽cutti ng edge profile n.切削刃轮廓〔外形，断面〕，切削刃角度cutt ing force n. 切削力cutti ng lip n.切削刃，刀刃，钻唇，钻刃cutt ing operation n. 切削加工，切削操作，切削作业cutti ng rate n.切削效率，切削速率cutti ng tool n.刀具，切削工具，刃具cycle n.周期，周，循环，一个操作过程，轮转，自行车cyli ndrical grin der n. 夕卜圆磨床Ddamage n.;vt.损坏〔害，伤，耗，失〕，破坏，事故，故障，伤害，危害deep-hole drilling n.深孔钻肖Udeep-hole milli ng n. 深孔铣削design n.设计，计算，计划，方案，设计书，图纸die-si nking n.凹模dime nsio n n.尺寸，尺度，维度，量纲，因次directi on of the feed moti on n. 进给方向，进刀方向discontinuous chip n. 间断切屑distanee n.距离，间隔〔隙〕，长度，vt.隔开double-colu mn pla ner-miller n. 双柱龙门铣床dress v.修饰，修整，平整，整理，清理，装饰，调制，准备，打磨，磨光，压平，轿直，清洗，清理，分级drilling n.钻头，钻床，穿孔器，凿岩机，v.钻孔，打孔，钻井，钻探drilli ng machi ne n. 钻床，钻机，钻孔机，打眼机drilling tool n.钻孔〔削，井，眼〕工具Eedge point n. 刀口，刀刃efficiency n.效率，效能，性能，功率，产量，实力，经济性，有〔功，实〕效end mill n. 立铣刀exter nal grinding n. 夕卜圆磨肖UFface n.表面，外观，工作面，表盘，屏，幕v.面向，朝向，表面加工，把表面弄平face grinding machi ne n. 平面磨床face milli ng mach ine n. 端面磨床feed force n. 进给力feed moti on n. 进给运动fine adjustme nt n.精调，细调，微调fine boring n.精密镗孔finish v.;n.精加工，抛光，修整，表面粗糙度，完工，最后加工，最后阶段，涂层，涂料fin ish-cutt ing n.精加工，最终切削fixture n.夹具，夹紧装置，配件，零件，定位器，支架form n.型式，类型，摸板，模型，形成，产生，成形，表格v.形〔组，构〕成，产生，作出，成形，造型form-turn n. 成形车削free-cutt ing n.自由切削，无支承切削，高速切削Ggap n.间隔，间隙，距离，范围，区间，缺口，开口火花隙，vt.使产生裂缝vi. 豁开gear cutt ing mach ine n. 齿轮加工机床，切齿机gear gen erati ng grin der n. 磨齿机gear hob n. 齿轮滚刀grinding cutter n. 磨具grinding force n. 磨削力grinding machi ne n. 磨床grinding wheel diameter n. 砂轮直径grinding wheel width n. 砂轮宽度groove n.槽，切口，排屑槽，空心槽，坡口，vt.切〔开，铣〕槽groove milling n. 铣槽Hheadstock sp in dle n. 床头箱主轴，主轴箱主轴，头架轴helical tooth system n. 螺旋齿轮传动装置high precisi on lathe n. 高精度车床high-speed n.高速high-speed mach ining n. 高速加工hob n.齿轮滚刀，滚刀，螺旋铣刀，v.滚铣，滚齿，滚削horsepower n.马力hobbing machine n.滚齿机，螺旋铣床，挤压制模压力机,反应阴模机hole n.孑L，洞，坑，槽，空穴，孔道，管道，v.钻〔穿，冲，开〕孔，打洞hone n. vt.磨石，油石，珩磨头，磨孔器，珩磨，honing mach ine n. 珩磨机，珩床，搪磨床，磨孔机，磨气缸机Iinclination n.倾斜，斜度，倾角，斜角〔坡〕，弯曲，偏〔差，角〕转in creme nt n.增量，增加，增〔大〕长in dex ing table automatic n. 自动分度工作台infeed grinding n. 切入式磨削in stallation n.装置，设备，台，站，安装，设置internal grinding n. 内圆磨肖Uin volute hob n.渐开线滚刀Jjig bori ng mach ine n. 坐标镗床Kkeyway cutt ing n.键槽切削加工kn urli ng tool n.滚花刀具，压花刀具，滚花刀Llaedscrew machi ne n. 丝杠加工机床lap grinding n.研磨lapping n.研磨，抛光，精研，搭接，擦准lathe n.车床lathe dog n.车床轧头，卡箍，鸡心夹头，离心夹头，制动爪，车床挡块lathe tool n.车刀level n.水平，水准，水平线，水平仪，水准仪，电平，能级，程度，强度，a.水平的，相等的，均匀的，平稳的loadi ng time n.装载料时间，荷重时间，充填时间，充气时间lock n.锁，栓，闸，闭锁装置，锁型，同步，牵引，v.闭锁，关闭，卡住，固定，定位，制动刹住Ion gitudi nal grinding n. 纵磨low capacity machi ne n. 小功率机床〔机器〕Mmach ine axis n. 机床中心线mach ine table n. 机床工作台mach ine tool n. 机床，工作母机machi ning n.机械加工，切削加工machi ning (or cutti ng) variable n. 力卩工(或切削)变量machi ning allowa nee n. 机械加工余量machi ning cycle n. 力卩工循环mach ining of metals n. 金属切削加工，金属加工magazi ne automatic n.自动化仓库，自动化料斗，自动存贮送料装置manu facture n.制造者，生产者，厂商，产品，制造material rem oving rate n. 材料去除率metal cutt ing n. 金属切肖U metal-cutt ing tech no logy n. 金属切削工艺学，金属切削工艺〔技术〕metal-cutti ng tool n. 金属切削刀具，金属切削工具micrometer adjustme nt n. 微调milling n.铣削，磨碎，磨整，选矿milli ng feed n.铣削进给，铣削走刀量，铣削走刀机构milli ng machi ne n. 铣床milli ng spi ndle n. 铣床主轴milli ng tool n.铣削刀具，铣削工具mount v.固定，安装，装配，装置，架设，n.固定件，支架，座，装置，机构mou nting n.安装，装配，固定，机架，框架，装置mounting fixture n. 安装夹具，固定夹具NNose n.鼻子，端，前端，凸头，刀尖，机头，突出部分，伸出部分nu mber of revoluti ons n. 转数nu merical con trol n. 数字控制nu merically con trolled lathe n. 数控车床Ooblique grinding n. 斜切式磨床operate v.操纵，控制，运行，工作，动作，运算operati ng cycle n. 工作循环operation n.运转，操作，控制，工作，作业，运算，计算operati onal in structi on n. 操作说明书，操作说明operati onal safety n. 操作安全性，使用可靠性oscillat ing type abrasive cutt ing machi ne n. 摆动式砂轮切割机oscillation n.振动，振荡，摆动，颤振，振幅out-cut milli ng n. 切口铣削oxide ceramics n. 氧化物陶瓷oxide-ceramic cutti ng tool n. 陶瓷刀具P。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
常用数控机床维护与维修中英文对照
1.absolute dimension（［di’menʃən］尺寸、大小、面积、规格）/
2.absolute coordinates（坐标）绝对尺寸/据对坐标值—距坐标系原点的直
线距离或角度
3. absolute programming 绝对编程—表示用绝对尺寸进行编程
4. absolute pulse code 据对位置编码器
5. accelerate 加速的
6. adapter 适配器
7. address 地址一个控制字开始的字符或一组字符，用以辨认其后的数据
8. ADI4 Analog Drive Interface for 4 Aixs 四轴模拟驱动接口
9. AIHPCC：AI high—precision contour control mode 智能插补高精度轮
廓控制方式
10. AI NANO：AI nano contour control mode 智能插补纳米精度控制方式
11. AICC：AI contour control mode 智能插补轮廓控制方式
12. Alarm报警
13. alter 取代
14. alternative current （AC）交流电
15.APCautomatically pallet change 自动托盘交换装置
16.arm手臂
17.ASCII美国信息交换标准法规
18.asynchronism motor 异步电动机
19.asynchronism 异步
20.ATC automatically tool change 自动刀具交换
21.ATC FWD自动刀具交换装置前进
22.ATC REV自动刀具交换装置后退
23.automatic lathe自动车床
24.Axis 轴
25.Backlash丝杠反向间隙
26.ball screw 滚珠丝杠
27.battery,lithium battery 电池，锂电池
28.Bearings 轴承
29.binary code二进制码
30.Block Format程序段格式
31. binary 二进制
32. Block程序段
33.Boring machines 镗床
34.Boring—milling 镗铣
puter part programming 计算机零件编程
36.Buffer缓冲器
mand Mode 指令方式
38.CAD计算机辅助设计
C lathes 数控车床
40.CAM计算机辅助制造
C grinding machines 数控磨床
42.cancel 取消
C engraving machines 数控雕刻机
44.Character 字符
C electric discharge machines 数控电火花机
46.Circular Interpolation 圆弧插补
C EDM writ—cutting machines数控电火花线切削机
48.Clockwise Arc (CW)顺时针圆弧
C drilling machines 数控钻床
50.Close—loop 闭环
51. CNC boring-milling machines 数控镗铣床
C bending presses 数控折弯机床
C boring machines数控镗床
puterized numerical control,CNC计算机数字控制
55.gear mechanism齿轮机构 55。
configuration建立、设定
56.general Machining centers 通用加工中心
57.control character 控制字符
58.graduate 刻度
59.coordinate system 坐标系
60.grinder磨床
61.counter 计数器
62.grinding 磨削
63.counterclockwise ARC（CCW）逆时针圆弧
64.hand 手，机械手
65.CRT阴极射线管
66.Hardware components--—-—硬件组成
67.Cutter Compensation刀具半径补偿
68.hard—wire 硬线连接
69.Data sheet 数据表
70.heavy—duty Lathes 重型车床
71.debug调试
72.hige-speed Lathes 告诉车床
73.decelerate 减速的
74.delet 删除
75.Diagnose诊断
76.die 模具
77.digital servo 数字伺服
78.direct current （DC）直流电
79.display显示
80.DNC直接数字控制
81.DNC—NC程序在线加工
82.double throw switch 双掷开关
83.double—pole single throw双刀单掷开关 75.double-ploe双极(刀开关）
84.DSP Digital Signal Process 数字信号处理器
85.EDIT：progamming editing 编辑方式
86.EIA美国电工学会标准
87.electric discharge machine （EDM)电火花机床
88.electronic pulse aa电脉冲
89.encoder 编码器
90.end of data 数据结束
91.end of program程序结束
92.EPROM可擦可编程只读存储器
93.Error 误差-计算值、观察值或实际值与真值、给定值或理论值之差
94.Ethernet 以太网
95.executive cycle执行循环】
96.Executive Program 执行程序 89.Feed Function进给功能
97.Feed Hold 进给保持
98.Feedback 反馈
99.filter out 过滤
100.Fixed Cycle，Canned Cycle固定循环
101.fluid servomotor伺服电机
102.FSSB FANUC Serial Servo Bus ——-- FANUC串行伺服总线
103.function 功能
104.HMI Human Machine Interface 人机界面
105.HND Manual handle feed mode 手轮方式
106. horizontal ＆ vertical Machining centers 卧式及立式加工中心107.horizontal Machining centers 卧式加工中心
108. HPCC:High—precision contour control mode 高精度轮廓控制109.INC：Incremental feed mode=step feed 增量进给
110. increase pulse code 增量编码器
111. Increment programming 增量编程
112. Incremental Dimension/Incremental Coordinates 增量尺寸/增量坐标值—在一序列点的增量中，各点距前一点的距离或角度值
113. Information 信息
114.input 输入（字符）
115. insert 插入（字符)
116.Instruction Code 指令码/Machine Code 机器码
117. Interpolation插补：在所需的路径或轮廓线上的两个已知点间根据某一数学函数(例如：直线、圆弧或高阶段函数）确定其多个中间点的位置坐标值的运算过程。
118. ISO国际标准化组织标准
119. JOG：jog feed 点动进给
120. Keeper 保持型继电器
dder diagram 梯形图
ther/ lathe车床
123. LCD 液晶显示器
124.Least command Increment 最小指令增量—从数值控制装置发出的命令坐标轴移动的最小增量单位
125.Least Input Increment 最小输入增量
126. LED发光二极管
127.Level switch （信号）液位开关
128.Line Interpolation 直线插补-这是一种插补方式，在此方式中,两点间的插补沿着直线的点群来逼近，沿此直线控制刀具的运动
129. linear guide 直线导轨
130.Lubricants 润滑液
131. Lubrication Systems 润滑系统
132.Machine Coordinates Origin机床坐标原点
133.Machine Coordinate System 机床坐标系—固定于机床上,以机床零点为基准的笛卡尔坐标系
134. Machine Program 加工程序
135.Machine tool 机床
136.Machine zero 机床零点
137.Machining center 加工中心
138.Macro program 宏程序
139. magazine attachment 机床送料装置
140.magazine feed 自动传输带(送料带）
141.magazine tool 刀库。