模具英语词汇大全
汽车冲压模具英语词汇
Die / Tool= 模具
Prog. Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套
Casting die=铸造模Cage=套
Part=钣件Rigidity=强度Die material=制模材料Thin=薄
Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”
Tool design approval=模具设计审核
Tool design modification/revision=模具设计更改
Tool parts design (detail) =模具钣件设计（详细）Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引
FMC Make=保丽龙制作Construction method=结构方法
modification= 更改
Check & measure=检查 & 测试
Machining= 机器加工
Large machining=在大型机器上加工上下模架（铣、车等）
Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块Lower trim inserts retainer=下模切刃块承盘
Assemble inserts=组立镶块
Punch stripping plates=冲头压料板
Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块Fitting=研磨组立Die tryout=试模
Spotting=合模Cushing stroke=缓冲行程
Dowel pin=定位销Guide lift pin=导引升降销
Assemble gas spring=安装氮气缸Stamp parts=冲钣件
Adjustment=调试Run off parts=冲钣件
Lower trim steels=下刃块Hit parts=冲钣件
Section=冲头断面Lifters=提升器
Trim punch=切刃冲头Coil=卷材
jack screw hole=起重[千斤顶]螺旋孔Guide block=导引块
Die set, lower plate=下模架Guide the coil through the tool=导引卷
材
Die set, upper plate=上模架layout inspection=全尺寸检验
Stretch carriers=拉伸运送装置
Die inspection & approval=模具检查和审
核
delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托
stop block=停止块Prepare for delivery=准备发货
Hydro form 液压成形Key=键
Shear=剪切For locating retainer blocks=承盘键Sensor=传感器For holding buttons or pilots=冲母座或
导销键
Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷Spotting red=合模用丹红
材
Checking aid /checking gage=检具Layout ink=试模用蓝墨水
Jig=夹具Masking tape=黄色不透明胶带(遮蔽胶带) Fixture=夹具Pliers=尖嘴钳，老虎钳
Ball bearing guide posts and bushings=
球形滚珠轴套
Cresent wrench=可调扳手
Guide post=导柱Bushings=导套Pump pipe=泵管
Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪
Symmetric=对称的
The axis of symmetry=对称轴Technical=技术上的
Diagonal=对角线
Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块
Granite Table=花岗岩平台Backing Plate=背板
Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记器, 标图员Shoulder Bolt=肩头螺丝(Stripper bolt)
Belt Sander=带磨机Keeper Block=行程块Metal Cutting Band Saw=立式带锯床Corner Guide Block=导块Blanchard Grinder=大型平面磨床Dowel pin=定位销
Joe Blocks=精密量块Set Screw=螺塞
Whirly Gig=筒夹式冲子成形器Jig & fixture =夹具Chamfer Tools=倒角刀具组Checking fixture=检具Angle Plate=L形直角座Guide Block=导块
Gage Pins=英寸塞规Plunger=柱塞
Sine Plate (magnetic)=正弦磁台Pierce=冲孔
Flute End Mill=硬质合金钢铣刀Wear Strip=耐磨板
Mill Cutter=波纹粗铣刀（标准型）Mating area=组立的接触面
C’bore/ counter bore=六角沉头铣刀Accommodate=适应
Radius Dresser=砂轮修整器Wiping hard (very shiny)= 过分摩擦闭合
[接触]（闪光）
Boring Head & Boring Bar=搪孔器、搪刀杆Pin=销Increase the die clearance between the form steels=增加成形块间隙
Reamer=绞刀Clearance=间隙
Approval=确认Oil paper=油纸
Impact wrench=气动扳手0-11” Micrometer=0-11”千分尺Air pin=空气销Trim line=切边
bumper
[‘bQmpE(r)] n.缓冲器+/-0.5mm unless otherwise specified 除非另有规定，否则公差为+/-0.5mm
Vendor [‘vendE(r), -dC:(r)] n.卖主Part tolerance=钣件公差stripper layout=排样图Ball nose=球刀
drawing of panel #987415&16=钣件设计图（公差）Bore=镗
Line tap=攻丝校直
Arbor =柄轴；心轴Borer=镗刀，镗床
Drill chuck=钻夹头Chamfer=倒角
Button=冲母座Radius=半径
Nitrogen Cylinder=氮气缸Coolant=切削液
Pilot=导销Punch=冲头
Retainer=承盘Distribution Blocks=接头座Button=冲母座Screw=螺丝
Hose Straps=软管夹（塑料）Shop=车间
Flat Feet Keepers=顶料销Crib=仓库
Ejector Pin=顶出销CNC mill= CNC机床
Spring=弹簧Jack=千斤顶
Straight Port Adapter=直管接头Strips=料条
Y-205 Hose=软管（塑料）Styrofoam [`stairEfEum]
n.聚苯乙烯泡沫塑料（保丽龙材料）Short Neck Adapter=短接头Cut off=落料
45。 Swivel= 45。接头(adjustable)Idle station=空站（for changeability of
the part in the future）
45。Elbow=45。接头(un-adjustable)Dry run=空转(to check the interference 干
涉of a die)
Compact Swivel Adapter=转接头Form=成形
Control Panel=控制面板Trim=切边
Stamp Retainer=承盘Perforate= [‘p\:fEreit] v.打孔Spotting press=合模机Plumber=水管工人[‘’plQmE(r)]
Hand grinder=角磨机Yo-yo 卷尺(美)
Surface grinder=平面磨床Drill chuck=钻头夹
Blanchard grinder=大型平面磨床Tape measure=卷尺
End mill=端铣刀/立端刀Protractor=量角器
Ball nose end mill=球头铣刀Switch=限位开关
Straight edge=直角座Caliper=卡尺
Shim stock=垫片Slug=废料
Oversize tap=加大尺寸丝攻Fittings=接头
Die=模具Crimping machine=氮气缸接头夹具
Upper die=上模Manual surface grinder=手动平面磨床
Lower die=下模Push cart=推车
Die set=模架Tool box=工具箱
Button die=冲母座Heel block=镶根
Pilot=导销Tap=攻丝
Bushing=衬套
Feeler gage=塞尺
HRS=hot roll steel =热轧钢卷Belt sander=砂带机
CRS=cold roll steel=冷轧钢卷Metal cutting band saw=带锯（切割金属）Insert=镶块Joe blocks=测量块
Guide post=导柱Scriber=划线器
Crane=吊机Zinc coating=镀锌
Stripper pad=压料板Ball peen hammer=球形榔头
Dowel pin=定位销Rosin=松香水
Heat treat=热处理Wire burn=线割Gage pins= Round cylinders of precise dimension used for measuring holes.
Fast wire burn=快走丝Blank die=下料模
Slow wire burn=慢走丝Tryout material=试模材料
Stripper pad=压料模(Pad retainer) shoulder bolt=stripper
bolt=肩头螺丝（all can be used for
guiding a pad）
Trim block (steel)=切刃块Pad retainer=压料模承盘
Form block (steel)=成形块Drill chuck=钻夹头
Drill vice=平口夹钳
Pig putty= epoxy Putty=油灰Parallel=平行块/肋条
Sandblast=喷沙器喷沙
(a pressurized air sand mixture)Graphite =石墨
（lubricant） [‘grAfait] n.
Plumb=
[plQm] n.铅锤, 铅弹 adj.垂直的
vt.使垂直, 用铅增加重量, 探测vi.垂直Plumber= n. 水管工人[‘plQmE(r)
Solder (lead)=
[‘sE u ldE(r); (?@) ‘s odEr] n.焊料 v.焊接 (铅条)Titanium nitrate (Tin coating-hard) =[化]硝酸钛 (钛化处理)
Binder= ‘ba indE(r)]
n.环模线，装订工, 包扎者, 包扎工具, Adjustable locking pliers (vice grip) =可调锁紧老虎钳
blind hole=闷眼, 盲孔Steel shavings=铁屑
slip fit=滑(动)配合Cast iron=铸铁
sliding chute=滑槽Threads=螺纹
Ratchet wrench 棘轮扳手Spacer block=间隔体(有时也叫平衡块) Vise grips=大力钳Semi-stripper=半脱件
Vargus debur tool=去毛刺器Clamp block=楔子
Disc grinder=砂轮机Killer pin=间隙调节螺栓
Air drill=气动手枪钻Restrike=整形
Hole gage=钻头规Extension pin=伸长销
Jack screw 起重[千斤顶]螺旋Conveyer=输送器
Screw hole=螺丝孔Spool retainer= 短管扣
Pin hole=导销孔Guide plate= 导板
Sheer cut=剪断Guide block= 导块
Thrust=推力Lock=锁定
Heel guide post=跟部导柱Preform=预成形
Kicker pin=踢出销Air bend= 自由弯曲
Set height stopper=设定高度阻止器Cam cut, cam pierce=剪断加工
Knock-out bar=顶出棒Gib=嵌条
Push-back=推出Single roll feed=单滚子进给
Cut=切断Gripper feed=夹爪进给
Pad=托板Grip finger=移动爪
Brake finger=固定爪
Slide feed=滑动进给
Single gripper feed=单夹爪进给
Hitch feed=紧扣进给
Pinch整缘Double roll feed=双滚子进给
Flash整缘Strip feed=带材进给
Wipe down整缘Hopper feed=漏斗进给
Trim flange整缘Station dial feed=分站圆盘进给
Horn type整缘Friction dial feed=摩擦圆盘进给Shimmy整缘Magazine feed=推进器进给
Post type=柱型Transfer feed=自移进给
Solid type=整体型Air blow ejector=空气喷出
Angle type=折角型Kicker=踢出件
Composite type=复合型Strap=夹条
Insert type=嵌入型Engineering=工程
Carbide cutters=硬质合金铣刀Distance block=平衡块
Balance block=平衡块
Washer/shim=垫片Pad balancer=平衡块
Datum=基准Hopper feed=
Notching punch= 凹口(局部落料)冲头French stop(feed stop) =进给停止器End mill=立端刀, 端铣刀Transfer punch=洋冲(used for drilling)
Neoprene
[`ni:Eupri:n] n.[化]氯丁(二烯)橡胶Set punch= a male punch shape to transfer to a female punch shape
Foundry [‘faundri]
n.铸造, 翻砂, 铸工厂, 玻璃厂, 铸造厂Sand-cast
砂型铸件, 砂型铸造
Velocity [v i’lositi]
n.速度, 速率, 迅速, 周转率Simulation-Draw die drawing 拉伸模设计模拟
Ball seat=眼泪水Square shear=剪板机
Draw bead=拉伸筋Pitch(progression)=步距
Draw lube=拉伸润滑油Flange=折边(通常为直边或90o折边)，凸
缘
Socket(deep & shallow) ratchet=
套筒扳手（深和浅）
Curl=卷边
Apex’s=气动扳手Channel locks=
Datum plane=.基准面Sand blast=喷砂处理，喷砂设备
Plane=平面Wrench work=钳工(工作) fitter=钳工Surface=表面 point=点 line=线Lathe man=车工
Solid=体，固体Initiator=开始者,引发剂
Body=空心体Planar Mill 龙门铣床
Planar [`pleinE(r),-na:(r)] =平面的Graphics Language=图学语言Offset=偏置
Projection=投影Draw=拉伸
Esperanto[espE‘rAntEu]
=世界语
Redraw=再拉伸
Engineering Drawing=工程图，工程制图Blank=下料
Graphic Science=图学Split=开缝
Descriptive Geometry=投影几何Notch= 做缺口
Representation of Diagrams=图表书法Separate=切离
Blue Print=蓝图Emboss=压花
Original Drawing=原图Joggle=榫接
Computer Graphics=电脑绘图Hemming=金卯合
RAM=记忆体random access memory Burr= 毛边
Plotter=绘图机CAM=凸轮工程
Geometry=几何Hook=吊钩
Circle=圆Leader=指线
Conic sections=割椎线Extension line=延伸线
Ellipse=椭圆Working drawing=工作图
Parabola=抛物线Full section=全剖面
Half section=半剖面
Hyperbola [ha i’pE:bElE]
=双曲线
Straight line=直线Broken-out section=局部剖面
Curves=曲线Rotated section=旋转剖面
Front view=前视图Removed section=移动剖面
Right side view=右侧视图Offset full section=偏置全剖面
Left side view=左侧视图Auxiliary review=辅助视图
Top view=俯视图Reference plane=参考平面
Bottom view=仰视图Projection weld=立式点焊机
Rear view=后视图Spot weld=点焊
Six principal views=六个主要视图Dash Panel=前隔板
Sectional view=剖视图interchangeable fixture=可互换的夹具（可拆
卸）
Blank die=下料模nut auto feeder=螺栓自动进料器
Transfer die=传送模Single gun=单枪
Clamping slot=U沟sequentially welded=按顺序焊接
Spring pin=弹簧导销stud projection welding machine=单植钉点焊
机
Sensors that determine part location=
welding fixture=焊夹具
钣件定位的限位开关
part gauging（gauge）=钣件定位规PLC控制器=可控程式器
cutting clearance=切边间隙gyroscopic suspension=葫芦悬架
dual sequence weld control=双向焊接控制器heavy -C- frame steel machine body
construction
=重负载C型架钢体机构
pneumatic clamping=气缸夹钳overhead frames/gantries with trolley=
上置式机架并带有吊枪用触轮
part presence sensing=钣件传感器sealer dispensing unit=封闭排种机构Panel Back Upper=后窗上补强件Handling hole=起吊孔
Bracket=补强件Tack weld=点焊
Nut=螺帽Bender pad=拉伸压料板
Stud=螺钉Stripper bolt=压料螺栓
Pad retainer=压料螺栓(两种)
Bolt=螺丝Interference＝干涉
Go 1=design approval, but not fabricate
Go 2=building approval (fabricate)
Bulkhead=隔板
Fast pitch=
Draw quality, special killed=拉伸质量，
特别裁断
Scallop=粗糙度=cusp=两曲线的交点,尖点
[‘skolEp]
Specify=指明
Normalize=调质（热处理解除内应力）Co-Axial Centering Indicator=寻边器Hemming=卷边
Sub-plate 模芯
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
模具英语词汇表汇编
模具英语词汇表 A abrasive grinding 强力磨削abrasive['breisiv] a.磨料的, 研磨的 absence ['bs ns] n.. 不在，缺席accessory[k'ses ri] n.附件 accommodate['k m deit] v. 适应 accordingly['k:di li] adv.因此,从而,相应地
accuracy['kjur si] n精度,准确性 actuate['ktjueit] vt.开动(机器), 驱动 adequate['dikwit] a. 足够的adhesive[d'hi:siv] n. 粘合剂 adjacent['d eisnt] a. 邻近的 adopt['d pt] vt. 采纳advance [d'v:ns] n.进步advisable [d'vaizbl] adj. 可取的agitate['d iteit] v. 摇动 a large extent 专门大程度algorithm ['l ri m] n. 算法 align ['lain] v 定位，调准alignment['lainm nt] n. 校直 all-too-frequent 频繁allowance['l uens] n. 容差, 余量 alternate[':lt nit]v.交替,轮流 alternative[:l't:n tiv]
n. 替换物 alternatively[:l't:n t ivli] ad. 做为选择, 也许aluminum[lju'minj m] n.铝 ample['mpl] adj. 充足的analysis ['n l sis] n. 分析 ancillary['nsil ri] a.补助的, 副的 angular ['jul] adj. 有角的 annealing['li:li ] n.退火 aperture ['p t ] n.孔applied loads 作用力appropriate ['pr uprieit] a. 适当的 arc[a:k] n.弧, 弓形 arise['raiz] vi. 出现, 发生 arrange['reid] v. 安排article['a:tikl] n.制品, 产品 ascertain[s'tein] vt. 确定, 查明
模具专业英语词汇
入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：spray diameter 流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot spray/cold runner 唧嘴直流: direct spray gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot spray 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 运水：water line 喉塞：line plug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug 模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar slot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 模具专业英语 推板：stripper plate 缩呵：movable core, return core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜楔：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B injection nozzle 射出喷嘴 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin
模具相关英语词汇大全(doc 25页)
模具相关英语词汇大全（doc 25页）
組裝、衝壓、噴漆等專業詞匯 Assembly line 組裝線Layout布置圖Conveyer流水線物料板Rivet table拉釘機 Rivet gun拉釘槍 Screw driver 起子 Electric screw driver電動起子 Pneumatic screw driver 氣動起子 worktable 工 作桌 OOBA開箱檢 查 fit together組 裝在一起 fasten鎖緊(螺 絲) fixture 夾具 (治具) pallet棧板 barcode條碼 barcode scanner條碼 掃描器 fuse together 熔合 fuse machine 熱熔機 repair修理 operator作業 員 QC品管 supervisor 課 長 ME制造工程 師 MT製造生技 cosmetic inspect外觀檢 查 inner parts inspect內部檢 查 thumb screw 大頭螺絲 lbs.inch鎊、英 寸 EMI gasket導 電條
|'plein|刨床miller銑床grinder磨床driller鉆床linear cutting 線切割electrical sparkle電火花 welder電焊機staker=revitin g machine鉚合機position職務president董事長 general manager總經理 special assistant manager特助factory director廠長 department director部長 deputy manager |'depjuti| =vice manager副理 section supervisor課 長 deputy section supervisor =vice section superisor副課 長 group leader/supervi sor組長 line supervisor線 長 assistant manager助理 to move, to carry, to handle搬運 be put in storage入庫 pack packing 包裝 to apply oil擦 油 to file burr 銼 毛刺 final inspection終 檢 to connect material接料 to reverse material 翻料 wet station沾
模具常用术语中英文对照
模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid
加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈（法兰）Locating Ring 柱子 Bossed 管钉（定位销）Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
冲压模具专业词汇中英文翻译
冲压模具词汇 Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表
模具英语专业术语
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance
模具专业的英语词汇大全
模具专业的英语词汇大全 一、模具专业英语 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock
模具专业英语词汇
Injection Mold Technical Terms （一）模具专业基本用词Professional Terms 塑料—plastic, resin 样件—sample 钢料—steel 注塑机—injection machine, press 产品—part, product, moulding 模具—mold, mould, tool A 简易模（样板模）—prototype mold B 量产用模具—production mold 三维造型（数模）—3D model, 3D data 二维产品图—2D part drawing 设计—design 制造—manufacture, build up, construction 检验—check, inspection 测量—measure, inspection 修改—change, modify, correction 工程更改—engineer change 质量—quality 数量—quantity 基准—datum, reference 牛角入水-rads gate （二）如何解析2D 产品图How to read 2D part drawing 产品几何Geometry 1．点—point 2．线（边）—line, edge 3．面face A 侧面—side B 表面—surface C 外观面—appearance surface 4．壁厚—wall thickness, stock thickness 5．加强筋（骨位）—rib 6．孔—hole 7．细长的槽—slot 8．柱位—boss 9．角—corner A 圆角—fillet B 倒角—chamfer C 尖角—sharp corner 10．斜度—angle, taper 11. 凹槽—recess , groove 分模信息Splitting 分型线—parting line (P/L), splitting line 主分模方向—main direction, line of draw 浇口设定—gating 产品标识Part Identification 产品名称—part name (P/N) 产品编号+版本号—part number + revision (Rev.)
常用模具英语单词
die 模具 figure file, chart file图档 cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板spare dies模具备品 bolt螺栓
模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube
五金模具常用专业术语中英文对照表[1]
五金模具常用专业术语中英文对照表 上模座upper die set成型公form punch 脱料板stripper 垫板subplate/backup plate 下模座die plate滑块CAM slider 垫脚parallel 误检misfeeder 托板mounting plate顶料销kick off 初始管位first start pin带肩螺丝shoulder screw 两用销lifter pin氮气汽缸gas spring 弹簧护套spring cage 拔牙螺丝jack screw 侧冲组件cam section 导正装置guide equipment 漏废料孔slug hole刀口trim line 加强装置enhance equipment 入子insert 护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head 扣位pocket of head 导柱guide post 导套guide bushing 油嘴oil nipple 接刀口mismatch/cookie bites 限位块stop block 挡块stopper 浮块lifter 压块keeper 靠块heel 对正块alignment block 简易模prototype tooling 检具gage/checking fixture 料带图strip layout 闭合高度shut hight 俯视图top view 料带strip 公差tolerance 正视图front view 走位travel 避位/空pocket 退磁demagnetization 间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting 镀钛TD coasting 沉头counter sink 精锣finish mill 线割wire cutting 穿丝孔first wire hole 斜度taper 镭射laser-cut 上夹板/固定座holder/retainer 下模座lower die set 成刑母公forming die 电火花EDM 码模槽mounting slot 球锁紧固定座ball-lock 导尺rail 球锁紧凸模BALL--LOCK 送料板rail plate 外购out sourcing 倒角chamfer 清角SCRAP CHOPPER 销钉dowel 尖角sharp --angle 普通弹簧coil spring 展开图EXPENSINg DWG 三打螺丝spool 镶件insert 毛刺burr 键销key 插针pilot pin
模具英语专业术语
模具（MOULD/MOLD，TOOL）： CAVITY：前模 CORE：后模（定模） DIMENSION：寸法 GATE：浇口/水口/入水口 PIN GATE：点水口/点浇入水 SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向 DRAFT ANGEL：脱模斜度 PARTING LINE/P。L：分模线 EJECT PIN/E。P：注塑顶针 BLAST/TEXTURE：喷啥，蚀纹 MIRROR FINISH：镜面（抛光）处理POLISH：抛光 EMD：放电加工 WELD：熔接加工（烧焊） LATHE：车床 MILLING CUTTER：铣刀 MILLING MACHINE：铣床 WIRE CUT：线切割 CNC：主加工中心 POWER DRILL：电钻 DRILLING：钻孔 FRITING：烧结 ANNEALING：淬火 注塑术语（INJECTION） SCREW：螺杆 WELD LINE：熔接线 SINK MARK：缩水 DRAG MARK：脱花 BURR：批锋 FLOW MARK：流纹 SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶 INJECTION CYCLE：成型周期
注塑英语 型厚大小 Thick size 锁模结构（机绞/直压） Mode locking structure(machine twists/straight pressure) 最大开模距离 The biggest die sinking is away from 动模板最大模具重量 Moves the template maximum mold weight 哥林柱间距 Elder brother forest column spacing 顶出形式（电动五点，油压五点，油压十三点） Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots) 顶出长度 Goes against the length 顶棍孔直径 Goes against the stick hole diameter 顶棍孔中心矩 Goes against the stick hole central moment 螺杆材质（合金） Screw rod material quality (alloy) 螺杆转速 Screw rod rotational speed 最大射出体积 Projects the volume most greatly 最大射出量 Projects the quantity most greatly 射出率 Ejection rate 每10mm射出量（理论） Each 10mm projects the quantity (theory) 射咀直径 Shoots ju the diameter 射咀R值 Shoots ju the R value 射咀空径 Shoots ju the spatial diameter 定位环直径 Locating ring diameter 溶胶能力 Sol ability 驱动方式（全自动/全液压）
模具常用英文词汇
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
模具专业英语词汇
extrusion mould 挤出模 extruder 挤出机 profile mould 异型材模具 calibrator 定型模 multi color co-extrusion tooling 多色共挤模具 hard and soft co-extrusion tooling 软硬共挤模具 mix materials co-extrusion tooling 混合材料共挤模具multi-cavity tooling 一模多腔 heavy-caliber PE 大口径PE the sandwich layer foams tube tooling 芯层发泡管模具die 模具，模头，机头 cap盖 duct 底槽 orifice 空口模 stamping 冲压 thermoplastic material 热塑性塑料材料 heat distortion 热畸变，热变形 insulated-runner system 绝热流道系统 hot-runner system internal heating 内加热 external heating 外加热 clamping force 锁模力 weld line 熔接线 air entrapment困气 sprue gate 注道型浇口
diaphragm gate 膜状浇口 ring gate 环形浇口 latch 板条 alloy 合金 deforming 变形casting 铸造，流延 mould cavity 模具型腔 single-cavity mould 单腔模 projected area 投影面积 side core 侧型芯 flow passage 流动通道 prototype mould 原型模具 vacuum 真空 quenched 淬火的 tempered 经过回火的 heat treatment 热处理 surface treatment 表面处理 wear resistance 耐磨损性 corrosion resistance 耐腐蚀性dimensional statability 尺寸稳定性nitriding steel 碳化钢 metal machining 金属加工 spark erosion 电火花技术 eletrode 电极电焊条 fine finishing 精加工，精修整 machine milling 机铣