RIP与静态路由重分布
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
RIP与静态路由重分布
一、网络拓扑图
二、设备配置
R1：
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos R1
R1(config)#int f 0/0
R1(config-if)#ip address 192.168.1.254 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R1(config)#int s 2/0
R1(config-if)#ip address 192.168.2.1 255.255.255.0
R1(config-if)#clo ra 64000
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
R1(config-if)#exi
R1(config)#router rip
R1(config-router)#ve 2
R1(config-router)#network 192.168.1.0
R1(config-router)#network 192.168.2.0
R1(config-router)#exi
R1(config)#do wr
Building configuration...
[OK]
R2:
Router>
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos R2
R2(config)#int s 2/0
R2(config-if)#ip address 192.168.2.2 255.255.255.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
R2(config-if)#exi
R2(config)#int s 3/0
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up R2(config-if)#ip address 192.168.3.1 255.255.255.0
R2(config-if)#clo ra 64000
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial3/0, changed state to down
R2(config-if)#exi
R2(config)#router rip
R2(config-router)#ve 2
R2(config-router)#network 192.168.2.0
R2(config-router)#default-information originate
R2(config-router)#redistribute static metric 3
R2(config-router)#exi
R2(config)#ip route 0.0.0.0 0.0.0.0 192.168.3.2
R2(config)#ip route 192.168.4.0 255.255.255.0 192.168.3.2
R2(config)#do wr
Building configuration...
[OK]
R3:
Router>
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos R3
R3(config)#int f 0/0
R3(config-if)#ip address 192.168.4.254 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R3(config)#int s 2/0
R3(config-if)#ip address 192.168.3.2 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#exit
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
R3(config)#ip route 0.0.0.0 0.0.0.0 192.168.3.1
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
R3(config)#ip route 192.168.2.0 255.255.255.0 192.168.3.1
R3(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1
Building configuration...
[OK]
测试结果：
从PC0 ping PC1: