手机测试标准0014-随机振动random vibration test TS-P–R–0014

2. PRINCIPLE 原则
The test consists of fixing mobile telephones to the table of a vibration generator and to monitor it in order to subject them to the requested vibration profil. 实验过程是把移动电话固定在振动台上，监控振动台确保样品符合所需的振动轮廓。
+ 6 dB/oct； 谱密度为 0.05 g2/Hz； 每个轴 1 小时； 3； 均方根 7.02g； 6.9mm。
PSD (g2/Hz)
0,1
0,01 10
页数 : 3/3
100 f (Hz)
1000
6. CHECKS 检查
The samples are checked and any damage is rated in compliance with the specification “Checking handsets –NOK123 sanctions” ref. TS-P–R–0077. 样品检查和损伤的判定要符合规范TS-P–R–0077“检查手机——NOK123判定”。
The sample holders must enable to hold the samples fixed on the table of the vibrator. The fixing devices used must comply with following characteristics : • They must avoid any vibration of the samples in the holders. • They must avoid to apply any additional strain to the samples than the one generated by the vibrations. 样品固定器确保样品固定在振动台上。使用的固定装置要满足以下特性： • 避免固定器上样品的振动； • 避免给样品施加除振动产生的应力以外的额外应力。
• Crest factor (σ) :
3.
• Average acceleration : 7,02 gRMS.
• Max displacement : 6,9 mm.
设置振动产生器按照如下随机振动轮廓运行：
• 从 10 到 20 Hz： • 从 20 到 500 Hz： • 持续时间： • 波峰因子(σ)： • 平均加速度： • 最大位移：
For information, this test is based on standard IEC 68-2-64. 需要更多信息，可以查询此实验的参考标准IEC 68-2-64。
3. NUMBER OF SAMPLES 样品数量
The recommanded number of samples is 3 devices. 推荐样品数量为3。
Do not perform checking on network simulators. 不用在网络仿真器上进行检查。
To fill in the heading of the sanction sheet ("Test Description" paragraph): • "Total number of test": enter “1”. • "Unit": enter "vibrations". 填写判定文件的表头（“实验描述”部分）： • “实验总次数”：输入“1”； • “单位”：输入“振动”。
编号 : TS-P-R-0014
版本 : 1.0
页数 : 2/2
1. GENERAL RULES 通用规则
See the following specifications:
“General rules for the performance of mechanical qualification tests” ref. TS-P–R–0080. 参考以下规范：TS-P–R–0080“机械性能实验的通用规则”
Ｑｕａｌｉｔｙ Ｉｎｓｐｅｃｔｉｏｎ Dept. Minister
质检部部长
Deputy Quality Director 质量副总监
Name 姓名 熊小妹
刘泽燕
刘月利
Date 日期 2006-9-28
2006-9-28
2006-10-8
Leabharlann Baidu
Signature 签名
熊小妹
刘泽燕
刘月利
TCT
Effective Date: 生效日期：2006-10-8
5. OPERATION METHOD 操作方法
The samples are all tested in a free order in the 3 perpendicular axis described beside : 样品按旁边描叙的3个正交轴进行实验，3个轴的顺序不做要求。
The samples are checked only at initial state (before vibrations), then at final state (after Z vibrations in the 3 axis). 样品只在初始状态（振动前）和最后状态（完成3个轴的振动后）进行检查。
7. REPORT 完成报告
See the following specifications: "General rules for the performance of mechanical qualification tests" ref. TS-P–R–0080. "Checking handsets - NOK123 sanctions" ref. TS-P–R–0077. 参考以下规范： TS-P–R–0080“机械性能实验的通用规则” TS-P–R–0077“手机检查——NOK123判定”
Doc No : TS-P-R-0014
Version : 1.0
Page : 1/1
RANDOM VIBRATION TEST
随机振动实验
PURPOSE OF THE TEST实验目的: The purpose of this test is to check the resistance of mobile phones to the mechanical strain due to random vibrations. 此实验为了检查移动电话抗随机振动引起的机械应力的能力。
Configuration of the samples during vibrations : • The handsets are fitted with a SIM card of any operator. • They are turned on and set to standby, synchronized to the network. • Clam shell and sliding product are tested closed.
Date 日期
2006-8-1
Version 版本
1.0
New Creation
Comments 备注
Written by 拟定
Verified by 审核
Approved by 批准
Function 职位
Ｑｕａｌｉｔｙ Ｉｎｓｐｅｃｔｉｏｎ Dept. Quality Technician 质检部质量技术员
The sample fixing devices must hold these products closed. 振动时样品配置：
• 手机插入任意运营商的 SIM 卡； • 手机开机，待机、同网络同步； • 实验中翻盖和滑盖产品合上。
样品固定装置必须保持这些产品处于合上状态。
The vibration generator must be set up in order to perform following
Preparation of samples (see TS-P–R–0080): The results of this test may be influenced by the presence of adhesive: NO. The results of this test may be influenced by the presence of a coating: NO. (coating = paint, varnish, metal finish, film in mold, film insert molding, stamped printing, pad printing, hot stamping, etc.). 样品的准备（参照TS-P–R–0080）： 此实验的结果可能受粘合剂的影响：否 此实验的结果可能受涂层的影响：否 （涂层包括：油漆、清漆、金属漆、模层、印刷层等。）
random vibration profil :
• From 10 to 20 Hz :
+ 6 dB/oct.
Y X
编号 : TS-P-R-0014
版本 : 1.0
• From 20 to 500 Hz : spectral density 0,05 g2/Hz.
• Duration :
1h by axis.
4. EQUIPMENT 设备
The vibration generator must have all characteristics in order to apply the requested vibration profil to the samples. 振动产生器应具有满足样品振动轮廓要求的所有性能。