永久性丙烯酸压敏胶中英文版MSDS
丙烯酸酯化学品安全技术说明书MSDS
5
包装类别：
Ⅱ
储运注意事项：
通常商品加有阻聚剂。储存于阴凉、通风仓间内。远离火种、热源。仓温不宜超过30℃。防止阳光直射。包装要求密封，不可与空气接触。不宜大量或久存。应与氧化剂分开存放。储存间内的照明、通风等设施应采用防爆型，开关设在仓外。配备相应品种和数量的消防器材。禁止使用易产生火花的机械设备和工具。定期检查是否有泄漏现象。灌装时应注意流速(不超过3m/s)，且有接地装置，防止静电积聚。搬运时要轻装轻卸，防止包装及容器损坏。
毒性危害
健康危害：
高浓度接触，引起流涎、眼及呼吸道的刺激症状，严重者可因肺水肿而死亡。误服急性中毒者，出现口腔、胃、食管腐蚀症状，伴有虚脱、呼吸困难、躁动等。长期接触可致皮肤损害，亦可致肺、肝、肾病变。
急救
皮肤接触：
用水冲洗，再用肥皂彻底洗涤。
眼睛接触：
立即提起眼睑，用流动清水或生理盐水冲洗至少15分钟。就医。
其他
工作现场严禁吸烟。工作后，淋浴更衣。注意个人清洁卫生。
丙烯酸酯
标识
中文名：
丙烯酸酯（丙烯酸及其同系物的酯类总称。）
英文名：
Esters of acrylic acid
理化性质
外观与性状：
无色液体，具有刺激的令人讨厌的，持久的气味。大多数沸点低，蒸气压高。
主要用途：
用于丙烯酸树脂的制造
溶解性：
微溶于水
燃烧爆炸危险性
燃烧性：
易燃
建规火险分级：
乙
闪点(℃)：
23～61
危险特性：
遇高热、明火有燃烧危险。蒸汽与空气能形成爆炸性混合物，与氧化剂接触会发生化学反应。容器在火场中有爆炸的危险。
燃烧(分解)产物：
MSDS-丙烯酸乳液(水性复膜胶水)
丙烯酸乳胶(水性复膜胶水)化学品安全技术说明书第一部分：化学品名称化学品中文名称：丙烯酸化气化学品英文名称：acrylic acid 英文名称2：propenoic acid技术说明书编码：917 CAS No.：79-10-7 分子式：C3H4O2分子量：72.06第二部分：成分/组成信息有害物成分含量CAS No.丙烯酸≥99.0％79-10-7第三部分：危险性概述危险性类别：不详侵入途径：不详环境危害：不详健康危害：本品对皮肤、眼睛和呼吸道有强烈刺激作用。
燃爆危险：本品易燃，具腐蚀性、强刺激性，可致人体灼伤。
第四部分：急救措施皮肤接触：立即脱去污染的衣着，用大量流动清水冲洗至少15分钟。
就医。
眼睛接触：立即提起眼睑，用大量流动清水或生理盐水彻底冲洗至少15分钟。
就医。
吸入：迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难，给输氧。
如呼吸停止，立即进行人工呼吸。
就医。
食入：用水漱口，给饮牛奶或蛋清。
就医。
第五部分：消防措施危险特性：易燃，其蒸气与空气可形成爆炸性混合物，遇明火、高热能引起燃烧爆炸。
与氧化剂能发生强烈反应。
若遇高热，可发生聚合反应，放出大量热量而引起容器破裂和爆炸事故。
遇热、光、水分、过氧化物及铁质易自聚而引起爆炸。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：消防人员须戴好防毒面具，在安全距离以外，在上风向灭火。
用水喷射逸出液体，使其稀释成不燃性混合物，并用雾状水保护消防人员。
灭火剂：雾状水、抗溶性泡沫、干粉、二氧化碳。
第六部分：泄漏应急处理应急处理：迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。
切断火源。
建议应急处理人员戴自给正压式呼吸器，穿防酸碱工作服。
不要直接接触泄漏物。
尽可能切断泄漏源。
防止流入下水道、排洪沟等限制性空间。
小量泄漏：用砂土或其它不燃材料吸附或吸收。
大量泄漏：构筑围堤或挖坑收容。
用防爆泵转移至槽车或专用收集器内，回收或运至废物处理场所处置。
丙烯安全技术说明书MSDS
化学品安全技术说明书第一部分化学品及企业标识化学品中文名：丙烯化学品英文名：propene|propylene化学品别名：-CAS No.：115-07-1EC No.：204-062-1分子式：CH3CHCH2产品推荐用途：请咨询生产商。
产品限制用途：请咨询生产商。
第二部分危险性概述| 紧急情况概述气体。
极端易燃,有爆炸危险。
高压，遇热有爆炸危险。
| GHS 危险性类别根据 GB 30000-2013 化学品分类和标签规范系列标准（参阅第十六部分），该产品分类如下：易燃气体，类别 1；高压气体，压缩气体。
| 标签要素象形图警示词：危险危险信息：极端易燃气体，内装高压气体；遇热可能爆炸。
防范说明预防措施：远离热源、热表面、火花、明火以及其它点火源。
禁止吸烟。
事故响应：漏气着火：切勿灭火，除非漏气能够安全地制止。
一旦发生泄漏，除去所有点火源。
安全储存：存放在通风良好的地方。
防日晒。
存放于通风良好处。
废弃处置：不适用。
| 危害描述物理化学危险极端易燃气体，有爆炸危险。
高压压缩气体，遇热有爆炸危险。
健康危害吸入该物质可能会引起对健康有害的影响或呼吸道不适。
由于本品的物理状态，一般没有危害。
在商业/工业场合中，认为本品不太可能进入体内。
通过割伤、擦伤或病变处进入血液，可能产生全身损伤的有害作用。
眼睛直接接触本品可导致暂时不适。
环境危害请参阅 SDS 第十二部分。
第三部分成分/组成信息第四部分急救措施| 急救措施描述一般性建议：急救措施通常是需要的，请将本 SDS 出示给到达现场的医生。
皮肤接触：立即脱去污染的衣物。
用大量肥皂水和清水冲洗皮肤。
如有不适，就医。
眼睛接触：用大量水彻底冲洗至少 15 分钟。
如有不适，就医。
吸入：立即将患者移到新鲜空气处，保持呼吸畅通。
如果呼吸困难，给于吸氧。
如患者食入或吸入本物质，不得进行口对口人工呼吸。
如果呼吸停止。
立即进行心肺复苏术。
立即就医。
食入：禁止催吐，切勿给失去知觉者从嘴里喂食任何东西。
PP-MSDS 英文版English
---------------------------------------------------------------最新资料推荐------------------------------------------------------PP-MSDS 英文版EnglishPart I: chemical name Chemicals Chinese name: polypropylene (isotactic) Chemicals English name: polypropylene Chinese alias: English alias: Technical manual coding: Formula: [C 3 H 6] n Molecular weight: Part II: Composition / Information Main components: pure CAS No.: 9003-07-0 Part III: Overview of risk Risk categories: Pathways: Health hazards: their non-toxic, pay attention to the toxicity of different additives. Pyrolysis products of acid, aldehyde and other eye, upper respiratory stimulation. Environmental hazards: Inhalation: Part IV: First Aid Measures Skin contact: Eye contact: Inhalation: remove to fresh air. If breathing is difficult, give oxygen. For medical treatment. Ingestion: Part V: Fire-fighting measures Hazardous characteristics: powder can form explosive mixtures with air, when a certain concentration and met Mars will be an explosion. Thermal decomposition flammable gases. Hazardous combustion products: Fire fighting methods: as far as possible to move containers from the scene empty Department. Extinguishing Media: Water spray, foam, dry powder, carbon dioxide, sand. Fire precautions and measures: Part VI: leak emergency Emergency treatment:1/ 6Isolation leak contaminated areas, restricting access. Cut off the fire source. Recommended emergency personnel wearing dust masks (full cover), wearing protective clothing. With clean shovel collection in a dry, clean, covered containers, transferred to a safe place. If large spills, recycling or collection shipped to the waste disposal sites.---------------------------------------------------------------最新资料推荐------------------------------------------------------ Part VII: Handling and Storage Handling Precautions: Storage: Store in a cool, ventilated warehouse. Away from fire and heat. Oxidants should be kept separate, sealed. Corresponding with the variety and quantity of fire-fighting equipment. Storage areas should be equipped with suitable host material spill. Part VIII: Exposure Control / Personal Protection Maximum allowable concentration: China MAC: 10; the former Soviet Union MAC: 10 Monitoring methods: Engineering controls: closed operation. Provide good natural ventilation. Respiratory protection: air concentrations exceeding the dust, it is recommended to wear self-absorption filter respirators. Eye protection: when necessary, wearing chemical protective safety glasses. Physical protection: wear protective clothing general operations. Hand protection: Wear protective gloves general operations. Other: no smoking scene work. Maintain good health habits. Part IX: Physical and Chemical Properties Appearance: white, odorless, tasteless solid. PH: Melting point (℃): 165-170 Boiling point (℃): Not available Relative density (water = 1): 0.90-0.91 Relative vapor density (air = 1): Not available Saturated vapor pressure (kPa): Not available Heat of combustion (kJ / mol): Not available Critical temperature3/ 6(℃): Not available Critical pressure (MPa): Not available Octanol / water partition coefficient as: Not available Flash point (℃): Not available Ignition temperature (℃): 420 (powder cloud) Explosion limit% (V / V): Not available Explosive limit% (V / V): 20 (g/m3) Solubility: Main purpose: used as engineering plastics for the system TV, radio shell, electrical insulation, corrosion pipes, plates, tanks, etc., but also for woven bags, packaging films. Other physical and chemical properties: Part 10: Stability and reactivity Stability: Conditions to avoid: INCOMPATIBILITY: Strong oxidizers. Hazardous Polymerization:---------------------------------------------------------------最新资料推荐------------------------------------------------------ Decomposition products: Part XI: Toxicological Information Acute toxicity: LD50: Not available, LC50: no information Subacute and chronic toxicity: Irritation: Sensitization: Mutagenicity: Teratogenicity: Carcinogenicity: Other: Part Ⅻ: Ecological Information Ecotoxicological toxicity: Biodegradation: Non-biodegradable: Bioconcentration or bioaccumulation of: Other harmful effects: Part ⅩⅢ: Waste disposal Nature of waste: Methods of disposal: Disposal in state and local regulations. Proposed incineration disposal. Waste Notes: Part XIV: Transport Information Dangerous Goods Code: no information UN Number: Not available Packaging signs: Packing Group: Z01 Packaging: No information. Transportation Note: Part XV: Regulatory Information National chemical safety regulations: Chemical Dangerous Goods Safety Management Regulations (February 17, 1987 the State Council), hazardous materials safety regulations implementation details (of labor [1992] No. 677), the workplace safe use of chemicals ([1996] Ministry of Labor No. 423) and other regulations for the safe use of hazardous chemicals, production, storage, transport, handling, etc. are made corresponding provisions; middle polypropylene plant air health standards (GB 16209-1996),5/ 6workshop provided the substance in the air and the maximum allowable concentration detection methods.。
丙烯MSDS报告
丙烯化学品安全技术说明书（MSDS）第一部分：化学品化学品中文名称：丙烯化学品英文名称：propylene;propene第二部分：成分/组成信息√纯品混合物第三部分：危险品概述危险性类别：第2.1类易燃气体侵入途径：吸入、食入、经皮吸收。
健康危害：本品为单纯窒息剂及轻度麻醉剂。
急性中毒：人吸入丙烯可引起意识丧失，当浓度为15％时，需30分钟；24％时，需3分钟；35％～40％时，需20秒钟；40％以上时，仅需6秒钟，并引起呕吐。
慢性影响：长期接触可引起头昏、乏力、全身不适、思维不集中。
个别人胃肠道功能发生紊乱。
环境危害：对环境有危害，对水体、土壤和大气可造成污染。
燃爆危险：本品易燃。
第四部分：急救措施吸入：迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难，给输氧。
如呼吸停止，立即进行人工呼吸。
就医。
第五部分：消防措施危险特征：易燃，与空气混合能形成爆炸性混合物。
遇热源和明火有燃烧爆炸的危险。
与二氧化氮、四氧化二氮、氧化二氮等激烈化合，与其它氧化剂接触剧烈反应。
气体比空气重，能在较低处扩散到相当远的地方，遇火源会着火回燃。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：切断气源。
若不能切断气源，则不允许熄灭泄漏处的火焰。
喷水冷却容器，可能的话将容器从火场移至空旷处。
灭火剂：雾状水、泡沫、二氧化碳、干粉。
第六部分：泄漏应急处理应急行动：迅速撤离泄漏污染区人员至上风处，并进行隔离，严格限制出入。
切断火源。
建议应急处理人员戴自给正压式呼吸器，穿防静电工作服。
尽可能切断泄漏源。
用工业覆盖层或吸附/ 吸收剂盖住泄漏点附近的下水道等地方，防止气体进入。
合理通风，加速扩散。
喷雾状水稀释、溶解。
构筑围堤或挖坑收容产生的大量废水。
如有可能，将漏出气用排风机送至空旷地方或装设适当喷头烧掉。
漏气容器要妥善处理，修复、检验后再用。
第七部分：操作处置与储存操作处置注意事项：密闭操作，全面通风。
操作人员必须经过专门培训，严格遵守操作规程。
丙烯酸树脂安全技术说明书
[丙烯酸树脂安全技术说明书（MSDS）］一、标识与成分化学品中文名称：丙烯酸树脂化学品英文名称:：Acrylic Resin技术说明书编码： LC/TS-12 生效日期：2009年2月15日消防救援电话：119纯品混合物√有害物成分: 浓度 CAS No.丙烯酸(杂）79—10—7二甲苯108-38—3丁醇 71-36—3二、危险性概述危险性类别：第3。
3类高闪点易燃液体侵入途径：吸入食人经皮吸收健康危害：接触加工或使用本产品对人体有危害。
对眼及上呼吸道有刺激作用，高浓度时对中枢神经有麻醉作用。
环境危害: 该物质对环境有危害,应特别注意对水体的污染.燃爆危险：易燃，其蒸气与空气可形成爆炸性混合物，遇明火、高热有燃烧爆炸危险.三、急救措施皮肤接触：脱去污染的衣着，用肥皂和清水彻底冲洗皮肤。
眼睛接触: 立即翻开上下眼脸，用流动清水或生理盐水冲洗至少15min，就医。
吸入：迅速脱离现场至空气新鲜处。
如呼吸困难，输氧;如呼吸停止，进行人工呼吸，就医。
食入：立即漱口饮水，催吐，洗胃，就医。
四、消防措施危险特性: 其蒸气与空气形成爆炸性混合物，遇明火、高热能引起燃烧爆炸。
蒸气比空气重，能在较低处扩散到相当远的地方，遇明火会引着回燃.燃烧时放出有害气体;流速过快，容易产生和积聚静电。
有害燃烧产物：燃烧时会有烟雾，并产生CO、CO2 。
灭火方法及灭火剂：可用泡沫、二氧化碳、干粉、砂土扑救，用水灭火无效.五、泄漏应急处理应急处理：切断火源。
迅速撤离泄漏污染区人员至安全地带，并进行隔离，严格限制出人。
建议应急处理人员戴自给正压式呼吸器,穿防毒服.尽可能切断泄漏源。
防止进入下水道、排洪沟等限制性空间。
小量泄漏：尽可能将溢漏液收集在密闭容器内，用砂土、活性碳或其他惰性材料吸收残液，可以用不燃性分散剂制成的乳液刷洗，洗液稀释后放入废水系统。
对使用过的洗液应稀释后放入废水处理系统,对使用过的吸附物必须送环保部门指定的填埋场或处理场所。
MSDS-丙烯酸乳液(水性复膜胶水)
丙烯酸乳胶化学品安全技术说明书化学品中文名称：丙烯酸化气化学品英文名称：acrylicacid 英文名称2：propenoic acid技术说明书编码：917 CAS No.：79-10-7 分子式：C3H4O2 分子量：72.06第二部分：成分/组成信息有害物成分含量 CAS No.丙烯酸≥99.0％ 79-10-7第三部分：危险性概述危险性类别：不详侵入途径：不详环境危害：不详健康危害：本品对皮肤、眼睛和呼吸道有强烈刺激作用。
燃爆危险：本品易燃，具腐蚀性、强刺激性，可致人体灼伤。
第四部分：急救措施皮肤接触：立即脱去污染的衣着，用大量流动清水冲洗至少15分钟。
就医。
眼睛接触：立即提起眼睑，用大量流动清水或生理盐水彻底冲洗至少15分钟。
就医。
吸入：迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难，给输氧。
如呼吸停止，立即进行人工呼吸。
就医。
食入：用水漱口，给饮牛奶或蛋清。
就医。
第五部分：消防措施危险特性：易燃，其蒸气与空气可形成爆炸性混合物，遇明火、高热能引起燃烧爆炸。
与氧化剂能发生强烈反应。
若遇高热，可发生聚合反应，放出大量热量而引起容器破裂和爆炸事故。
遇热、光、水分、过氧化物及铁质易自聚而引起爆炸。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：消防人员须戴好防毒面具，在安全距离以外，在上风向灭火。
用水喷射逸出液体，使其稀释成不燃性混合物，并用雾状水保护消防人员。
灭火剂：雾状水、抗溶性泡沫、干粉、二氧化碳。
第六部分：泄漏应急处理应急处理：迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。
切断火源。
建议应急处理人员戴自给正压式呼吸器，穿防酸碱工作服。
不要直接接触泄漏物。
尽可能切断泄漏源。
防止流入下水道、排洪沟等限制性空间。
小量泄漏：用砂土或其它不燃材料吸附或吸收。
大量泄漏：构筑围堤或挖坑收容。
用防爆泵转移至槽车或专用收集器内，回收或运至废物处理场所处置。
第七部分：操作处置与储存操作注意事项：密闭操作，加强通风。
丙烯英文版MSDS
Chemical Safety Data SheetSECTION 1 CHEMICALS & COMPANYProduct Name: PropeneTelephone ：Company :Shandong Yinuo Chemical Industry Co.,LtdZip Code ：251500 Cas NO: 115-07-1 File No ：008 Effective Date: Mar 1,2013SECTION 2 COMPONENTComponent ：PropeneCAS No.：115-07-1. Purity: ＞99.5％SECTION 3 DANGEROUSNESSClass ：2.1 Inflammable Gas Invasive ways: suctionHealth Hazard: This product is a simple asphyxiant and mild anesthetic.Acute Poisoning: Inhaled propylene can cause loss of consciousness, when the concentration is 15%, need 30 minutes; 24% when, should be 3 minutes; When 35% ~ 40%, to 20 seconds; When more than 40%, only 6 seconds, and lead to vomiting.Chronic Effects: Long-term exposure can cause dizziness, fatigue, concentration, whole body discomfort, thinking individuals gastrointestinal function disorders.Environmental Hazards: Has harm to the environment, water, soil and air can cause pollution.Combustion Hazard: Flammable, the steam can form explosive mixtures with air, flame is burning explosion hazard.SECTION 4 FIRST AID MEASURESSkin Contact: no data. Eye contact: no data.Sucked Into: quickly from the scene to fresh air place. Keep the airway open. Such as the breath is difficult, give oxygen. If breathing stops, immediately to people or to breathe. Go to a doctor.Eat: nonsense .SECTION 5 FIRE CONTROL MEASURESDangerous Features: Flammable, mixed properties can form explosive mixtures with air, with heat and open flame is in danger of burning explosion, and carbon dioxide, nitrogen tetroxide, nitrous oxide and other chemical combination, contact with other antioxidant violent reaction, the gas is heavier than air and can be spread in the low to very far place, meet fire can cause burning back.Hazardous Combustion Products: Carbon monoxide, carbon dioxide.Fire Extinguishing Method And Agent: C ut off the gas source, if not immediately cut off the gas source, are not allowed to put out the burning gas, water spray cooling container, possible move container from fire to open.Agent: water fog, foam, carbon dioxide, dry powder.Fire Precautions: water spray cooling combustion cans and near tanks, until the end of fire extinguishing. Tank in case of changes in a fire or abnormal sound, should be evacuated immediately. Put out the fire with water is invalid.SECTION 6ACCIDENTAL RELEASE MEASURESEmergency Treatment:Leave quickly leak contaminated area personnel to windward, and isolation and strictrestrictions in and out, cut off the fire, suggested that the emergency response personnel wear self-contained breathing apparatus, fire protective clothing, cut off the leak source as far as possible, in industrial coating or adsorption/absorption agent cover near the leak place such as sewer, prevent gas entering. Reasonable ventilation, accelerate the diffusion, spray water dilution, dissolve, constructing dike or dig a pit for produce the large amount of waste water, if possible, use leakage gas exhaust fan sent to the empty place or furnishappropriate nozzle burned, leak container to properly handle, repairing, inspection before use.SECTION 7 DISPOSAL AND STORAGE OPERATIONOperation Note:Airtight operation, the comprehensive ventilation. Operators must receive special training, strictly abide by the operation procedures. Away from fire and heat source, workplace smoking is strictly prohibited. Use explosion-proof ventilation systems and equipment. Prevent gas leakage in the air of workplace. Avoid contact with oxidant, acid type. In the process of transmission, the cylinder and the container must be grounded and jumper, prevent to produce static electricity. Light light discharge when handling to prevent damage to the cylinder and accessories. Equipped with corresponding varieties and number of fire equipment and spill contingency processing equipment.Storage precautions:flammable compressed gas. Store in a cool, dry and ventilated good non-combustible warehouse. Warehouse temperature should not exceed 30 ℃. Away from fire, heat source, prevent direct sunlight. Should work with oxygen, compressed air, halogen () of fluorine, chlorine, bromine, antioxidant, etc. Storage room lighting, ventilation facilities should use explosion-proof type, switch is located in outside warehouse. When tank storage should have technical measures for fire and explosion prevention.SECTION 8 CONTACT CONTRO/LINDIVIDUAL PROTECTIONThe Highest Permissible Concentration: The MAC (mg/m3) standardsThe former Soviet union MAC (100 mg/m3)The United States TVL - TWAACGIH asphyxiationUs the TLV - STEL formulated standardsMethods: gas chromatographyEngineering Control: closed production process, comprehensive ventilation. Provide a good natural ventilation. Respiratory Protection:generally don't need special protection, high concentrations of contact can be self-priming filter type gas mask (half mask).Eye Protection: generally don't need special protection, high concentrations of contact can be wear chemical safety gogglesBody Protection: wear anti-static overalls. Hand protection: wear protective gloves.Other Protection:work site no smoking. Avoid high suction. Into the cans, restrictive space or other high concentration area, must be watched.SECTION 9 PHYSICAL AND CHEMICAL PROPERTIESAppearance and properties: colorless, scents of hydrocarbon gases.PH: no dataOctanol/Water Partition Coefficient: no dataMelting point (℃). The relative density of 191.2 (water = 1) : 0.5Boiling point (℃) : the relative density of 47.7 (air = 1) : 1.48Saturated vapor pressure (kPa) : 602.88 (0 ℃) heat of combustion (kJ/mol) : 2049Critical temperature (℃) : 91.9 critical pressure (MPa) : 4.62Flash point (℃) : - 108 explosive limit % (V/V) : 15.0Ignition temperature (℃) : 455 lower explosive limit % (V/V) : 1.0Solubility: soluble in water, ethanol. Minimum ignition energy (mj) : 0.282Main USES: the main acrylonitrile, propylene oxide, acetone, etc.Other physical and chemical properties: the maximum explosion pressure (MPa) 0.843SECTION 10 the STABILITY AND REACTIVITYStability: stable prohibited content: strong oxidant, acid.Avoid contact with the condition: heat, open flame.Polymerization: polymerizationHazardous combustion products: carbon monoxide, carbon dioxideSECTION 11TOXICOLOGY DATAAcute Toxicity: LD50 mg/kg through the mouth (mice) LC50 mg/m3, 2 hours (suction) in miceSubacute And Chronic Toxicity: mice inhaling this product concentration was 35%, 20 times, causing mild fatty liver soaks.Stimulus: no data Allergenic: no dataRespectively: no data Teratogenicity: no dataCarcinogenic effects: no data Other: no dataSECTION 12 INFORMATION ECOLOGYEcological Toxicity: this material has harm to the environment, to give special attention to the fish and water. Should also pay special attention to surface water, soil, air and water pollution.Biodegradability: no dataThe Biodegradability: no dataBiological Enrichment Or Cumulative: no dataOther Harmful Effects: no dataSECTION 13 WASTE DISPOSAL□Industrial solid wasteWaste Material PropertiesWaste Disposal Method: before disposal shall refer to the national and local relevant laws and regulations. Proposal with incinerating disposal.Scrap Notice: before disposal shall refer to state and local relevant laws and regulations, waste storage, see "storage and transportation considerations".SECTION 14 TRANSPORTATION INFORMATIONDangerous Goods Number: 21018 The UN NO. : 1077Packing Mark: flammable gas Packaging categories:Ⅱclass wrapping Packing Method: steel cylinders.Transportation Note:this product use railway transport time pressure liquefied gas enterprise should bring along their own tanker shipment, need to be submitted to the relevant departments for approval before shipment. Using just bottle transport must wear a good helmet on the cylinder. General flat cylinder, and the bottle should be in the same direction, do not cross; Fencing height shall not exceed the vehicle plate, with triangle wood mat card, to prevent rolling. Transport transport vehicles should be equipped with corresponding varieties and number of fire equipment. Shipment the goods vehicle exhaust pipes must be equipped with fire equipment, mechanical equipment and tools to ban the use of easy to produce sparks loading and unloading. It is strictly prohibited during mixed with oxidant, acid, etc. Summer should be transport in the morning and evening, to prevent exposure to the sun. Stopover should be far away from fire and heat source. When highway transportation route, according to the rules, don't stay in residential areas and densely populated area. Railway transportation should prohibit humping.SECTION 15 REGULATORY INFORMATIONHazardous chemical materials safety management regulations (January 9, 2002, 52 times under the state council executive meeting, released on January 26, since March 15, 2002), in view of the hazardous chemicals safety in production, use, storage, transportation, loading and unloading, etc, have made the corresponding provisions; Commonly used the classification of dangerous chemicals and mark (GB 13690-92), the material is divided into class 2.1 flammable gases.SECTION 16 OTHER INFORMATIONReference: 1. The list of dangerous chemicals (2002)2. The commonly used the classification of dangerous chemicals and mark (GB 13690-92)3. Safety net in China4 "petrochemical dangerous chemicals practical handbook"5. The hazardous chemical materials safety technical specifications ", 1997, Zhou Guotai.Time to fill out a form: on March 1, 2013Department of filling: the security officeData audit units: security officeModify description: second, unmodified.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
永久性丙烯酸压敏胶中英文版MSDS 化学品中文名称：丙烯酸
化学品英文名称： acrylic acid
英文名称：propenoic acid
健康危害：本品对皮肤、眼睛和呼吸道有强烈刺激作用。
皮肤接触：立即脱去污染的衣着，用大量流动清水冲洗至少15分钟。
就医。
眼睛接触：立即提起眼睑，用大量流动清水或生理盐水彻底冲洗至少15分钟。
就医。
吸入：迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难，给输氧。
如呼吸停止，立即进行人工呼吸。
就医
食入：用水漱口，给饮牛奶或蛋清。
就医。
危险特性：易燃，其蒸气与空气可形成爆炸性混合物，遇明火、高热能引起燃烧爆炸。
与氧化剂能发生强烈反应。
若遇高热，可发生聚合反应，放出大量热量而引起容器破裂和爆炸事故。
遇热、光、水分、过氧化物及铁质易自聚而引起爆炸。
有害燃烧产物：一氧化碳、二氧化碳。