锂离子电池专业英语

锂离子电池专业英语

2

———————————————————————————————— 作者： ———————————————————————————————— 日期：

3

锂离子电池常用专业英语 （一） 序号 首字母 英文 中文 1 A aging 老化 2 B battery charger 充电器 3 black-fleck 黑斑 4 C cap 盖板 5 capacity density 能量密度 6 capacity grading 分容 7 cathode tab welding 极耳超焊 8 cell 电芯 9 charge(capacity) retention 荷电（容量）保持 10 checking code 检码 11 concave spot 凹点 12 constant current charge 恒流充电 13 constant current discharge 恒流放电 14 constant voltage charge 恒压充电 15 corrective measures 纠正措施 16 crack 裂纹 17 cut-off voltage 终止电压 18 cycle life 循环寿命 19 D dark trace 暗痕 20 degrade 降级 21 dent 凹痕 22 discharge depth 放电深度 23 distortion 变形 24 drape 打折 25 E Electrical and MechanicalServices Department 机电部 26 electrolyte 电解，电解液 27 empaistic 压纹 28 end-off voltage 放电截止电压 29 environmentally friendly 对环境友好 30 equipment first inspection 设备首检 31 erode 腐蚀 32 explosion-proof line 防爆线 33 F first inspection 首检 34 formation 化成 35 fracture 断裂 36 I inspection 检验 37 insulate 绝缘 38 internal resistance 内阻 39 J jellyroll 卷芯 40 joint 接缝，结合点

4

41 L laser deflecting 偏光 42 laser reticle 激光刻线 43 laser welding-flatwise weld 激光焊接-平焊 laser welding-standing weld 激光焊接-立焊 44 leakage 漏液 45 leak-checking 测漏 46 leaving out of welding 漏焊 47 limited charge voltage 充电限制电压 48 local action 自放电 49 M margin turnly 翘边 50 measuring the dimension of cells 电芯卡尺寸 51 meet requirement 达到要求 52 memory effects 记忆效应 53 N nick 划痕 54 nominal voltage 标称电压 55 notice-board confirmation 看板确认 56 nugget 硬块 57 O obverse 正面 58 open circuit voltage 开路电压 59 over charge 过充 60 over discharge 过放 61 over the thickness 超厚 62 P particle 颗粒 63 PE membrane PE膜 64 pit 坑点 65 placing cells into the box 电芯装盒 66 point inspection 点检 67 preventive measures 预防措施 68 pricking the tapes 扎孔 69 process inspection 制程检验 70 put the battery piled up 将电芯叠放在一起 71 Q qualified products 合格品 72 quality assurance 质量保证 73 quality control 质量控制 74 quality improvement 质量改进 75 quality match 品质配对 76 quality planning 质量策划 77 R rated capacity 额定容量 78 recharge 再充电 79 refitting the can of cell 电芯壳口整形 80 requirment 要求 81 reverse 背面，反面 82 rework 返工 83 ringing cells into pyrocondensation films 套热缩膜

5

84 S safety vent 安全阀 85 sand aperture 砂眼 86 scar 疤痕 87 secondary battery 二次电池 88 select appearance 选外观 sharp-set 批锋 89 short circuit checking 测短路 90 smudginess 污物 91 spot welding by laser 激光点焊 92 spot welding place 点焊位置 93 spraying the code 喷码 94 spur 毛刺 95 sticking the PVC cover boards 贴面垫 96 storing 陈化 97 storing with high voltage 高压储存 98 T tabs deflection 极耳歪斜 99 tabs excursion 极耳错位 100 technics requiment 工艺要求 101 U ultrasonic welding 超声波焊接 102 ultrasonic welding strength 超焊强度 103 unqualified products 不合格品 104 W wave 波浪 105 working procedure 工序

（二） 盖板 cover board 底板solepiece 钢珠steel ball 压钢珠press steel ball 防爆阀valve preventing explosion 大电流(倍率)放电discharge in high rate current 标称电压Normal voltage 标称容量normal capacity 放电容量discharge capacity 充电上限电压limited voltage in charge 放电下限电压terminating voltage in discharge 恒流充电constant current charge 恒压充电constant voltage charge 恒流放电constant current discharge 放电曲线discharge curve 充电曲线charge curve

6

放电平台discharge voltage plateau 容量衰减capacity attenuation 起始容量initial discharge capacity 流水线pipelining 传送带carrying tape 焊极耳welding the current collector 卷绕wind 叠片layer 贴胶带stick tape 点焊spot welding 超声焊ultrasonic welding 三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials 钴酸锂Cobalt Lithium Oxide 锰酸锂Manganese Lithium Oxide 石墨graphite 烘箱oven 真空烘箱vacuum oven 搅拌机mixing device vacuum mixing device 涂布机coating equipment 裁纸刀paper knife ,,,,,,cutting knife 分条机equipment for cutting big piece to much pieces 辊压机roll press equipment 电阻点焊机spot welding machine 超声点焊机ultrasonic spot welding machine 卷绕机winder 自动叠片机auto laminating machine 激光焊机laser welding machine 注液机infusing machine 真空注液机vacuum infusion machine 预充柜pre-charge equipment 化成柜formation systems 分容柜grading systems 测试柜testing systems 内阻仪battery inner resistance tester 万用表multimeter 转盘式真空封口机turntable type vacuum sealing machine 自动冲膜机automatic aluminum membrane shaper