专业英语 锂离子电池
锂电池专业英语
盖板c o v e r b o a r d 底板s o l e p i e c e 钢珠s t e e l b a l l 压钢珠p r e s s s t e e l b a l l 防爆阀v a l v e p r e v e n t i n g e x p l o s i o n大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic weldingThe terminating voltage in discharge of the battery is volt. The limited voltage in charge of the battery is volt.三元素Nickle-Cobalt-Manganese Lithium Oxidethree elements materials钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing devicevacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces 辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper。
锂离子电池专业英语
锂离子电池常用专业英语（一）序号首字母英文中文1 A aging 老化2 B battery charger 充电器3 black-fleck 黑斑4 C cap 盖板5 capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 charge(capacity) retention 荷电（容量）保持10 checking code 检码11 concave spot 凹点12 constant current charge 恒流充电13 constant current discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 纠正措施16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 D dark trace 暗痕20 degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 E Electrical and MechanicalServices Department 机电部26 electrolyte 电解，电解液27 empaistic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 腐蚀32 explosion-proof line 防爆线33 F first inspection 首检34 formation 化成35 fracture 断裂36 I inspection 检验37 insulate 绝缘38 internal resistance 内阻39 J jellyroll 卷芯40 joint 接缝，结合点41 L laser deflecting 偏光42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接-平焊laser welding-standing weld 激光焊接-立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51 meet requirement 达到要求52 memory effects 记忆效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE膜64 pit 坑点65 placing cells into the box 电芯装盒66 point inspection 点检67 preventive measures 预防措施68 pricking the tapes 扎孔69 process inspection 制程检验70 put the battery piled up 将电芯叠放在一起71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量控制74 quality improvement 质量改进75 quality match 品质配对76 quality planning 质量策划77 R rated capacity 额定容量78 recharge 再充电79 refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面，反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜84 S safety vent 安全阀85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smudginess 污物91 spot welding by laser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压储存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqualified products 不合格品104 W wave 波浪105 working procedure 工序（二）盖板 cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic welding三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials 钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing device vacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper锂离子电池设计专业英语Capacity 容量Battery Thickness 电池厚度Battery width 电池宽度Battery length 电池高度Impedance 内阻Can thickness 壳体厚度Can wall thickness 壳体壁厚Can bottom thikness 壳体底部厚度Can lid thickness 壳体盖板厚度PP film thickness PP胶厚度Ni (AL) tab thickness Ni（Al）极耳厚度Battery width 电池宽度Can width margin 电池宽度留边Can length 壳体长度Can cross area 壳体体积Winding pin width 卷针宽度Can Side residue 壳边残余Naked battery thickness 裸漏电池厚度Naked battery width 裸漏电池宽度Naked battery length 裸漏电池高度Cathode formulation 阴极含量Cathode material specific capacity 阴极克比容量Cathode 阴极装填Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode weight 阴极重量Cathode thickness 阴极厚度Cathode elongation rate 延伸率Cathode actual length 阴极实际长度Cathode design length 阴极设计长度Cathode width 阴极宽度Cathode Scratched area width 阴极涂片宽度Al foil density 铝箔密度Al foil thickness 铝箔厚度Cathode weight 阴极重量Separator thickness 隔离膜厚度Separator length 隔离膜长度Separator width 隔离膜宽度Separator density 隔离膜密度Separator weight 隔离膜重量Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode loading 阳极装填量Anode area density 阳极面密度Anode bulk density 阳极体积密度Anode thickness 阳极厚度Anode length 阳极长度Anode width 阳极宽度Anode scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度Anode weight 阳极重量Cathode Tab length 阴极极耳长Cathode Tab width 阴极极耳宽Cathode Tab thickness 阴极极耳厚度Anode Tab length 阳极极耳长度Anode Tab width 阳极极耳宽度Anode Tab thickness 阳极极耳厚度Adhesive tape Length 胶带长度Adhesive tape Width 胶带宽度Adhesive tape thickness 胶带厚度Assembly adhesive tape 装配胶带Bottom length 底部长度Bottom Width 底部宽度Bottom Thickness 底部厚度Top length 顶部长度Top Width 顶部宽度Top Thickness 顶部厚度Welding length 焊接长度Welding Width 焊接宽度Welding Thickness 焊接厚度Electrolyte 电解液Battery Impedance 电心内阻Battery weight 电池重量Can wall thickness 壳体壁厚Can bottom thikness 壳体底厚Can lid thickness 盖板厚度Can width margin 壳体边缘宽度Can Side residue 壳体留边Cathode formulation 阴极含量Cathode material specific capacity 阴极克容量Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode elongation rate 阴极延伸率Cathode scratched area width/Pin width 阴极刮粉宽Al foil density 铝箔密度Al foil thickness 铝箔厚度Separator thickness 隔离膜厚度Separator density 隔离膜密度Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode bulk density 阳极体积密度Anode Scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度欢迎您的下载，资料仅供参考！致力为企业和个人提供合同协议，策划案计划书，学习资料等等打造全网一站式需求。
英语词汇大全(电池行业)-电池名称
英语词汇大全—电池1.Alkaline batteries ：碱性电池2.Capacitor batteries：电容电池3. secondary battery 二次电池4. Rechargeable batteries ：充电电池5. Primary batteries ：原电池6. Lithium batteries ：锂电池7. Lithium ion batteries ：锂离子电池8. Lithium polymer batteries：锂聚合物电池9. Environmental Protection batteries:环保电池10. Nickel iron batteries ：镍铁电池11. Nickel cadmium batteries ：镍镉电池12. Carbon zinc batteries ：碳锌电池13. Nickel zinc batteries：镍锌电池14. Zinc air batteries：锌空电池15. Silver zinc batteries：银锌电池16. Zinc chloride batteries：银氯化物电池17.Silver oxide batteries ：银氧化物电池18. Silver cadmium batteries ：银钙电池19. Lead calcium batteries：铅钙电池20. Lead acid batteries：铅酸电池21. Lead-acid starter batteries：起动铅酸电池22. Lead-acid traction batteies：牵引用铅酸电池23. Aircraft lead-acid batteries：航空用铅酸电池24. Sealed lead acid batteries：密封铅酸电池25. Lead-acid batteries for stationary valve-regulated：固定型阀控密封式铅酸蓄电池26. small-sized valve-regulated lead-acid batteries：小型阀控密封式铅酸电池27. Lead-acid batteries for motorcycles：摩托车用铅酸电池28. Lead-acid batteries for disel locomotive：内燃机车用铅酸电池29. Lead-acid batteries for electric road vehicles：电动道路车辆用铅酸电池。
关于电池的英语
Lithium batteries 锂电池Lithium ion batteries 锂离子电池Cylindrical Li-ion battery 圆柱形电池Prismatic Li-ion battery 方形电池Soft-pack Li-ion battery 软包装电池Lithium polymer batteries 锂聚合物电池LiFePO4 Li-ion batteries 磷酸铁锂电池Lead acid batteries 铅酸电池Primarybatteries 原电池Nickel metal hydride batteries(Ni-Mh) 镍氢电池Nickel-Cadmium battery(Ni-Cd) 镍镉电池Nickel zinc batteries 镍锌电池Nickel iron batteries 镍铁电池Alkalinebatteries 碱性电池Capacitor batteries：电容电池Carbon zincbatteries 碳锌电池Lead calciumbatteries 铅钙电池Rechargeable batteries 充电电池EnvironmentalProtectionbatteries 环保电池stationary battery 固定型蓄电池portable battery 携带式蓄电池starter battery 启动用蓄电池traction battery 牵引用蓄电池motorcycle battery 摩托车用蓄电池train lighting battery 火车照明用蓄电池aircraft battery 航空用蓄电池aerobatic battery 特技飞行用蓄电池Emergency battery 应急用蓄电池Original equipment battery 设备原配蓄电池Replacement battery替换用蓄电池Pilot cell指示电池Plate (of a battery)极板Positive plate正极板Negative plate负极板Plante plate形成式极板普朗特极板Spacer隔离物Separator (of a battery)隔板Terminal (of a battery端子，极柱Negativeterminal负极端子，负极柱Electrolyte电解质，电解液Container蓄电池壳，蓄电池槽monobloc Container整体壳,整体槽Edge Insulator绝缘卡Cover Lid蓄电池盖Sealingcompound密封剂:封口剂Ventvalve排气阀Electrolytelevel indicator液位指示器Baffle保护板Intercell Connector 连接条/线Outputcable输出电缆Terminalconnector端子连接条Batterytray蓄电池组合箱/组外壳Batterybase蓄电池底垫Batteryrack电池架。
锂离子电池专业英语
锂离子电池常用专业英语（一）序号首字母英文中文1 A aging 老化2 B battery charger 充电器3 black-fleck 黑斑4 C cap 盖板5 capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 charge(capacity) retention 荷电（容量）保持10 checking code 检码11 concave spot 凹点12 constant current charge 恒流充电13 constant current discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 纠正措施16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 D dark trace 暗痕20 degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 E Electrical and MechanicalServices Department 机电部26 electrolyte 电解，电解液27 empaistic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 腐蚀32 explosion-proof line 防爆线33 F first inspection 首检34 formation 化成35 fracture 断裂36 I inspection 检验37 insulate 绝缘38 internal resistance 内阻39 J jellyroll 卷芯40 joint 接缝，结合点42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接-平焊laser welding-standing weld 激光焊接-立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51 meet requirement 达到要求52 memory effects 记忆效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE膜64 pit 坑点65 placing cells into the box 电芯装盒66 point inspection 点检67 preventive measures 预防措施68 pricking the tapes 扎孔69 process inspection 制程检验70 put the battery piled up 将电芯叠放在一起71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量控制74 quality improvement 质量改进75 quality match 品质配对76 quality planning 质量策划77 R rated capacity 额定容量78 recharge 再充电79 refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面，反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smudginess 污物91 spot welding by laser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压储存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqualified products 不合格品104 W wave 波浪105 working procedure 工序（二）盖板cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic welding三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials 钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing device vacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper锂离子电池设计专业英语Capacity 容量Battery Thickness 电池厚度Battery width 电池宽度Battery length 电池高度Impedance 内阻Can thickness 壳体厚度Can wall thickness 壳体壁厚Can bottom thikness 壳体底部厚度Can lid thickness 壳体盖板厚度PP film thickness PP胶厚度Ni (AL) tab thickness Ni（Al）极耳厚度Battery width 电池宽度Can width margin 电池宽度留边Can length 壳体长度Can cross area 壳体体积Winding pin width 卷针宽度Can Side residue 壳边残余Naked battery thickness 裸漏电池厚度Naked battery width 裸漏电池宽度Naked battery length 裸漏电池高度Cathode formulation 阴极含量Cathode material specific capacity 阴极克比容量Cathode 阴极装填Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode weight 阴极重量Cathode thickness 阴极厚度Cathode elongation rate 延伸率Cathode actual length 阴极实际长度Cathode design length 阴极设计长度Cathode width 阴极宽度Cathode Scratched area width 阴极涂片宽度Al foil density 铝箔密度Al foil thickness 铝箔厚度Cathode weight 阴极重量Separator thickness 隔离膜厚度Separator length 隔离膜长度Separator width 隔离膜宽度Separator density 隔离膜密度Separator weight 隔离膜重量Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode loading 阳极装填量Anode area density 阳极面密度Anode bulk density 阳极体积密度Anode thickness 阳极厚度Anode length 阳极长度Anode width 阳极宽度Anode scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度Anode weight 阳极重量Cathode Tab length 阴极极耳长Cathode Tab width 阴极极耳宽Cathode Tab thickness 阴极极耳厚度Anode Tab length 阳极极耳长度Anode Tab width 阳极极耳宽度Anode Tab thickness 阳极极耳厚度Adhesive tape Length 胶带长度Adhesive tape Width 胶带宽度Adhesive tape thickness 胶带厚度Assembly adhesive tape 装配胶带Bottom length 底部长度Bottom Width 底部宽度Bottom Thickness 底部厚度Top length 顶部长度Top Width 顶部宽度Top Thickness 顶部厚度Welding length 焊接长度Welding Width 焊接宽度Welding Thickness 焊接厚度Electrolyte 电解液Battery Impedance 电心内阻Battery weight 电池重量Can wall thickness 壳体壁厚Can bottom thikness 壳体底厚Can lid thickness 盖板厚度Can width margin 壳体边缘宽度Can Side residue 壳体留边Cathode formulation 阴极含量Cathode material specific capacity 阴极克容量Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode elongation rate 阴极延伸率Cathode scratched area width/Pin width 阴极刮粉宽Al foil density 铝箔密度Al foil thickness 铝箔厚度Separator thickness 隔离膜厚度Separator density 隔离膜密度Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode bulk density 阳极体积密度Anode Scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度。
充电器 词汇
Alkaline batteries ：碱性电池Capacitor batteries：电容电池Carbon zinc batteries ：碳锌电池Lead acid batteries：铅酸电池Lead calcium batteries：铅钙电池Lithium batteries ：锂电池Lithium ion batteries ：锂离子电池Lithium polymer batteries：锂聚合物电池铅酸蓄电池Lead-acid battery起动铅酸电池Lead-acid starter batteries摩托车用铅酸电池Lead-acid batteries for motorcycles内燃机车用铅酸电池Lead-acid batteries for disel locomotive电动道路车辆用铅酸电池Lead-acid batteries for electric road vehicles小型阀控密封式铅酸电池small-sized valve-regulated lead-acid batteries航空用铅酸电池Aircraft lead-acid batteries固定型阀控密封式铅酸蓄电池Lead-acid batteries for stationary valve-regulated 铅酸电池用极板plate for lead-acid battery铅锭lead ingots牵引用铅酸电池Lead-acid traction batteies电解液激活蓄电池electrolyte activated batteryvent valve 排气阀filling device for pleral cells 电池组填充装置negative electrode 负电极negative plate 负极板addition reagent for negative plate 负极板添加剂indicator 指示器top cover 上盖vent plug 液孔塞expanded grid 扩展式板栅specific gravity indicator 比重指示器electrolyte level control pipe 电解液液面控制管electrolyte level indicator 电解液液面指示器electrolyte level sensor 电解液液面传感器hard rubber container 硬橡胶槽envelope separator 包状隔板woven cloth tube 纺布管spongy lead 海绵状铅partition 隔壁over the partition type 越过隔壁型through the partition type 贯通隔壁贯通型separator 隔板(1)battery rack(2)battery stand(3)battery stillage 蓄电池架/蓄电池底垫active material 活性物质glass fiber separator 玻璃纤维隔板glass mat 玻璃纤维绵glass mat tube 玻璃纤维绵管spacing washer 间隔垫圈reinforced fiber separator 强化纤维隔板polarity mark plate 极性标记板pole 极柱pole insulator 极柱绝缘子pole nut 极柱螺母plate 极板plate foot 极板足plate supporter 极板支撑件element 极板群/极群组pole bolt 极柱螺栓plate lug 极板耳dilute sulfuric acid 稀硫酸steel can 金属罐steel container 金属蓄电池槽(1)madribs(2)element rest 鞍子/极群组座tubular plate 管状极板gelled electrolyte 胶体电解液grid 板栅caution label 警告标签synthetic resin separator 合成树脂隔板plastics container 塑料蓄电池槽synthetic fiber separator 合成纤维隔板connector sunken type 沉没型连接器connetor exposed type 露出型连接器safety valve test 安全阀测试ampere-hour efficency 安时效率one charge distance range 一次充电行程gas recombination on negative electrode type 阴极气体再化合型/阴极气体复合型cut-off discharge 终止放电/截止放电(1）specific characteristic (2)energy density (1)比特性（2）能量密度recovering charge 恢复充电(1)open circuit voltage(2)off-load voltage 开路电压/空载电压overcharge 过充电gassing 析气overcharge life test 过充电寿命试验accelerated life test 加速寿命试验active material utilization 活性物质利用率theoretical capacity of active material 活性物质的理论容量over discharge 过放电intermittent discharge 间歇放电full charge 完全充电full discharge 完全放电reverse charge 反充电/反向充电quick charge 快速放电allowable minimum voltage 允许最小电压equalizing charge 均衡充电creeping 蠕变group voltage 组电压shallow cycle endurance 轻负荷寿命/轻负荷循环寿命characteristic of electrolyte decrease 电解液减少特性nominal voltage 标称电压high rate discharge 高率放电high rate discharge characteristic 高率放电特性5 second voltage at discharge 放电5秒电压（1）cold cranking ampere（2）cold cranking performance （1）冷启动电流（2）冷启动性能cycle life test 循环寿命测试maximum voltage at discharge 最大放电电压30 second voltage at discharge 放电30秒电压residual capacity 残存容量(1)hour rate(2) discharge rate （1）小时率（2）放电率(1) self discharge (2) local action （1）自放电（2）局部自放电(1) self discharge rate(2) local action rate （1）自放电率（2）局部自放电率actual capacity 实际容量(1)starting capability(2)cranking ability 启动能力cranking current 启动电流battery clamp test 电池夹钳测试power density 功率密度momentary discharge 瞬间放电modified constant voltage charge 修正恒定电压充电initial capacity 初始容量gas recombination by catalyser type 触媒气体复合式initialcharge 初始充电viberation test 振动试验predetermined voltage 预定电压total voltage 总电压activation test for dry charged battery 干式荷电蓄电池活化试验salting 盐析earthquake-proof characteristics 防震性能dielectric voltage withstand test 电介质耐压试验short time discharge 短时间放电escaped acid mist test 酸雾逸出测试terminal voltage 端子电压cell voltage 单电池电压step charge 阶段充电short-circuit current 短路电流storage test 保存测试high rate discharge at low temperature 低温高率放电rated voltage 额定电压rated capacity 额定容量fixed resistance discharge 定阻抗放电constant voltage charge 恒压充电constant voltage life test 恒压寿命测试constant current charge 恒流充电constant voltage constant current charge 恒流恒压充电constant current discharge 恒流放电constant watt discharge 恒功率放电low rate discharge characteristics 低率放电特征trickle charge 涓流充电trickle charge current 涓流充电电流trickle charge life test 涓流充电寿命测试thermal runaway 热失控driving pattern test 运行测试capacity in driving pattern test 运行测试boost charge 急充电floating charge 浮充电floating charge voltage 浮充电电压floating charge current 浮充电电流(1)mean voltage (2)average voltage 平均电压on-load voltage 负载电压discharge duration time 放电持续时间(1)final voltage(2)cut-off voltage(3)end voltage 终止电压/截止电压depth of discharge 放电深度discharge voltage 放电电压discharge current 放电电流discharge current density 放电电流密度discharge watt-hour 放电瓦时discharge characteristics 放电特性discharged ampere-hour 放电安时explosion proof test 防爆测试auxiliary charge 补充电maintenance factor 维护率storage characteristics 保存特性gas recombinating efficiency 气体复合效率/气体再化合效率charge 充电charge acceptance test 充电可接受性试验start-of-charge current 充电开始电流charge efficiency 充电效率end-of-charge voltage 充电结束电压specific gravity of electrolyte at the end of charge 充电结束时电解液比重charge voltage 充电电压charge current 充电电流charged watt-hour 充电瓦时charge characteristic 充电特性charge ampere-hour 充电安时deep cycle endurance 重负荷循环寿命/重复合寿命weight engergy density 重量能量密度rubber pad 橡胶垫lower level line 下液面线side terminal 侧端子collective exhaust unit 公共的排放单元sintered plaque 烧结极板sintered separator 烧结隔板sintered plate 烧结极板catalyst plug 催化塞spine 芯骨strap 带spacer 隔离物insulating tube 绝缘管intercell connector 连接线/连接条connector cover 连接管盖float mounted plug 浮动安装的栓(1)pasted plate (2)grid type plate 涂膏式极板braidd tube 编织管(1)flame-arrester vent plug (2)flam-retardant vent plug 安全塞explosion and splash proof construction 防爆防溅结构baffle 保护板pocket type plate 袋式极板bottom hole-down 底孔向下（固定）bolt fastening terminal 螺栓连接端子male blade 阳片monoblock container 整体槽positive electrode 正极positive plate 正极板leading wire terminal 引线端子retainer mat 止动垫片ribbed separator 肋隔板(1)jumping wire (2)inter low wire 跳线end plate 端板filling plug 注液塞plante plate 形成式极板/普朗特极板tubular plate 管式极板low electric resistance separator 低电阻隔板tapered terminal post 锥形接线柱electrolyte 电解液container 蓄电池槽/蓄电池壳set of container 成套蓄电池槽level-scope mounted plug 透视塞/透视栓handle 手柄jug 取液管(1)connector;(2)plug concent (1)连接器；(2)插座式连接器connector wire 连接线connecting bar 连杆connecting bar cover 连杆帽lead 引线/连接线edge insulator 绝缘卡side frame 侧框架battery cubicle 蓄电池箱perforated separator 多孔隔板burning rod (铅)焊条terminal 端子terminal connector 端子连接条terminal cover 端子盖terminal base 端子座tab 接线片lead bushing 铅套corrugated separator 波形隔板(1)lead dioxide;(2)lead peroxide (1)二氧化铅；(2)过氧化铅(1)woven separator;(2)nonwoven separator (1)织物隔板；(2)非织物隔板vent hole 通气孔exhaust tube 排气管antipolar mass 反极性物质output cable 输出电缆microporous rubber separator 微孔像胶隔板specific gravity indicator 比重计leaf separator 叶片式隔板lid sealing compound 密封剂/封口剂sealing gasket 密封衬垫/垫圈lid 蓄电池盖set of lid 系列的盖1.精滤器secondary filter high efficiency filter2、反渗透装置主机reverse osmosis unit3、反渗透膜reverse osmosis membrane4、数显示电导仪digital conductivity apparatus5、面板式流量计panel type flow meter6、混合离子交换器mixed-ion exchanger7、配套树脂supporting resin8、732阴树脂732 negative resin9、酸碱再生装置acid and alkali regenerative unit10、直线型铅碇输送机linear type lead ingot conveyer11、自动恒温熔铅炉melting furnace with automatic constant temperature12、铅棒冷却槽lead stick cooling tank13、铅粉视密度lead powder apparent density14、卸料阀discharge valve15、布风屏cloth besel锂离子电池专业英语和大家分享一下，有不足的欢迎大家补充！方通盖板cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic weldingThe terminating voltage in discharge of the battery is 3.0 volt. The limited voltage in charge of the battery is 4.2 volt.三元素Nickle-Cobalt-Manganese Lithium Oxidethree elements materials钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing devicevacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces 辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper序号首字母英文中文1 A aging 老化2 B battery charger 充电器3 black-fleck 黑斑4 C cap 盖板5 capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 charge(capacity) retention 荷电（容量）保持10 checking code 检码11 concave spot 凹点12 constant current charge 恒流充电13 constant current discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 纠正措施16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 D dark trace 暗痕20 degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 E Electrical and MechanicalServices Department 机电部26 electrolyte 电解，电解液27 empaistic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 腐蚀32 explosion-proof line 防爆线33 F first inspection 首检34 formation 化成35 fracture 断裂36 I inspection 检验37 insulate 绝缘38 internal resistance 内阻39 J jellyroll 卷芯40 joint 接缝，结合点41 L laser deflecting 偏光42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接-平焊laser welding-standing weld 激光焊接-立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51 meet requirement 达到要求52 memory effects 记忆效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE膜64 pit 坑点65 placing cells into the box 电芯装盒66 point inspection 点检67 preventive measures 预防措施68 pricking the tapes 扎孔69 process inspection 制程检验70 put the battery piled up 将电芯叠放在一起71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量控制74 quality improvement 质量改进75 quality match 品质配对76 quality planning 质量策划77 R rated capacity 额定容量78 recharge 再充电79 refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面，反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜84 S safety vent 安全阀85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smudginess 污物91 spot welding by laser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压储存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqualified products 不合格品104 W wave 波浪105 working procedure 工序Voltage：Units of measuring electrical current, all batteries are rated in volts DC. (Direct Current). This determines how much energy is needed to power your equipment.Voltage plateau:（电压平台）A slow decrease in voltage over a long period of time. As a rule, the plateau extends from the first voltage drop at the start of the discharge to the bend of the curve after which the voltage drops rapidly at the end.Nominal Voltage（标称电压）The voltage of a battery, as specified by the manufacturer, discharging at a specified rate and temperature.Working voltage（工作电压）The working voltage of a cell or battery begins at its electrical connections as soon as an electrical consumer is connected to it.Discharging voltage, average voltage (放电电压)The average discharging voltage is the average value of the discharging voltage during the entire discharging process with a related discharging current.Open circuit voltage (OCV开路电压)The voltage of a battery when there is no current flowing.Closed-Circuit Voltage (CCV闭路电压)The potential or voltage of a battery when it is discharging or charging.State of charge:The rate of charge capacity vs. whole capacity.Initial voltage（起始电压）A battery＇s initial voltage is the working voltage when discharging begins. End-point voltage (End voltage, Cutoff voltage, Final voltage)截止电压Specified closed circuit voltage at which a service output test is terminated. End-of-discharge voltageThe battery voltage when discharge is terminated.End-of-charge voltageThe battery voltage when charge is terminated.Cutoff voltage (V)The battery voltage at which charge or discharge is terminated.Definition: Capacity(容量）? The capacity of a cell is defined as how manymilli-amp-hours (mAh) of current the cell canstore and subsequently deliver.? One milli-amp (mA) is 1/1000th of an Amp. Somelarger cell capacities are expressed in Amp-hours(Ah).? “Rated capacity” is varies with discharge rate,temperature, and cutoff voltage.? Rated capacity is different from power or energy? Example:? If a cell is rated at 1000 mAh, then it can deliverthe following:? 1000 mA of current for 1 hour? 500 mA of current for 2 hours? 200 mA of current for 5 hours? 2000 mA of current for 1/2 hourDefinition: Energy Density(能量密度，包括体积比能量和质量比能量）? The energy density of a cell is a measure of howmuch energy can be stored in the cell per unitvolume or per unit weight.? E (watt-hours) = cell voltage x capacity rating? Energy density per unit volume is called the“volumetric energy density” and is expressed interms of watt-hours/liter (wh/l).? Energy density per unit weight is called the“gravimetric energy density” and is expressedin terms of watt-hours/kilogram (wh/kg).? These measurements are useful when you aretrying to determine which cell has the mostcapacity per unit volume or weight.1.Self Discharge 自放电2.Uniformity of the Li-ion Batteries 锂离子电池的一致性3.steel strap 钢带4.Burst vent 防爆阀5.Filling port 注液孔6.spirally wound type cylindrical wound type 圆柱形7.foil 箔8.parallel-plate prismatic design 方形叠片式设计Ageing （老化）- Permanent loss of capacity with frequent use orthe passage of time due to unwanted irreversible chemical reactions in the cell.Anode（阳极）- The electrode in an electrochemical cell where oxidation takes place, releasing electrons.During discharge the negative electrode of the cell is the anode.During charge the situation reverses and the positive electrode of the cell is the anode.Cathode（阴极）- The electrode in an electrochemical cell where reduction takes place, gaining electrons.During discharge the positive electrode of the cell is the cathode. During charge the situation reverses andthe negative electrode of the cell is the cathode.Cycle （循环）- A single charge and discharge of a battery.Depth of discharge DOD （放电深度）- The ratio of the quantity of electricity or charge removed from a cell on discharge to its rated capacity.Internal impedance（交流内阻）- Resistance to the flow of AC current within a cell. It takes into account the capacitive effect of the plates forming the electrodes.Internal resistance （直流内阻）- Resistance to the flow of DC electric current within a cell, causing a voltage drop across the cell in closed circuit proportional to the current drain from the cell.A low internal impedance is usually required for a high rate cell.锂离子电池的内阻英语概念到底用哪个概念，是Internal resistance还是Internal impedance，一些电池说明书内阻用Internal resistance，也有的用Internal impedance，我认为Internal impedance较好些，因为国内测的电池内阻基本都是交流内阻，而外文也有这样定义的（我在别的帖子也粘贴过）：Internal impedance（交流内阻）- Resistance to the flow of AC current within a cell. It takes into account the capacitive effect of the plates forming the electrodes.Internal resistance （直流内阻）- Resistance to the flow of DC electric current within a cell, causing a voltage drop across the cell in closed circuit proportional to the current drain from the cell.A low internal impedance is usually required for a high rate cell.在IEC6196002中，只定义为Internal resistance，而用交流的方法测得的内阻，叫Internal a.c. resistance（交流内阻）用直流的方法测得的内阻，叫Internal d.c. resistance（直流内阻），其实Internal a.c. resistance测得就是阻抗，这样看来不如用Internal impedance（交流内阻）和Internal resistance （直流内阻）这两个概念把它们进行分清，以免混淆。
锂离子电池 英文
Electrolyte
• The selection of the electrolyte depends on the potential window. • Potentials are beyond water potential and hence non aqueous electrolyte. • It should not reactive with Li+ ions, since it will decide the transport of the Li+ ions for the intercalation reaction. • The electrolyte solution commonly comprises a lithium salt dissolved in a mixture of organic solvents. • Examples include LiPF6 or LiBOB (the BOB is the anion with the boron coordinated by two oxalate groups) in an ethylene carbonate/dimethyl carbonate solvent.
Li Ion Battery (LIB)
Battery
• Battery: Transducer which converts chemical energy into electrical energy. • Chemical reactions: Oxidation and reduction • Free energy change of the processes appears as electrical energy. • Primary battery-not rechargeable • Secondary battery- rechargeable
电化学专业词汇锂离子电池
电化学专业词汇锂离子电池Stoichiometry 化学计量学Cyclability 循环特性Rate capability 倍率性能Life-span 寿命The state of the art 目前的工艺水平Overall assessment 综合评价Basis for 为…打基础Rational selection 合理的选择辅助动力混合电动车（Power-Assist Hybrid Electric Vehicles ，包括HEV和FCV）；插电式混合电动车（Plug-in Hybrid Electric Vehicles ，包括PHEV 和FCV)纯电动车（Battery Electric Vehicles ，包括各类EV)R&D （research and development），指在科学技术领域，为增加知识总量（包括人类文化和社会知识的总量），以及运用这些知识去创造新的应用进行的系统的创造性的活动，包括基础研究、应用研究、试验发展三类活动。
可译为“研究与开发”、“研究与发展”或“研究与试验性发展”。
DOE 美国能源部Passivation 钝化Hydrophobic 疏水性Lipophobic 疏酯性Solvophobic 疏溶剂的Aggregate 聚集Micelle 胶团微团Fluorosurfactant 氟表面活性剂Impermeable 不可渗透的Electrolyzer 电解槽Redox flow battery 氧化还原液流电池Intrinsic 本质的固有的Novel approach 新方法Delocalization 离域移位Steric shield 空间屏蔽Nucleophilic attack 亲核攻击Spur 鼓舞马刺刺激鞭策Resurgence 复活再现New platform 新平台Fuel flexibility 燃料灵活性Cusp 风口浪尖Power generator 电力发电机Forklift 铲车Stumbling block 绊脚石Methanol 甲醇Formic acid 甲酸Dimethyl ether 二甲醚Performance decline 绩效下滑Peroxide 过氧化物过氧化氢Chloromethylation氯甲基化Aromatic polymer 芳族聚合物Styrene 苯乙烯Quaternization 碱化反应Benzylchloride 氯化苄Tertiary amine 叔胺Quaternary 四进制的四元的Ammonium 铵Tether 范围Linkage 连接Facile 温和的灵巧的Monomer 单体Precursor 前驱体Brominated 溴化Benzylhalide 苄基氯Subsequent 随后的Backbone 支柱中坚Bucket 水桶Susceptible 易受。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Owing to its ascendant performance, now lithium-ion is the fastest growing and most promising battery chemistry.
2.Introduction
2.1 Construction
Lithium-ion battery
Positive electrodes LiNiO2, LiCoO2, LiMnO2, LiFePO4, LiMn2O4 Negative electrodes MCMB, graphite, LixSi, LixCd, SnO, Li4Ti5O12, Electrolyte PAN, PVDF, Separators
is the most commonly
used Li-ion cell. Mostly used in notebook
application, it boasts the
lowest cost per watt hour.
Prismatic or brick-shaped Li-ion cells often are cost-
them in a jellyroll fashion like cylindrical or prismatic cells.
3.Application
Chemical name Lithium Cobalt Oxide* Lithium Manganese Oxide* Material LiCoO2 (60% Co) LiMn2O4 Abbreviation Short form Applications LCO LMO Li-cobalt Li-manganese, or spinel Cell phone Laptop, Camera e-bikes, Electric vehicles, Medical, Hobbyist Gaining importance in electric powertrain and grid storage
no free lithium metal.
Disadvantages
1. Requires protection circuit to maintain voltage and
current within safe limits.
2. Subject to aging, even if not in use.
Lithium Iron Phosphate*
Lithium Nickel Manganese Cobalt Oxide* Lithium Nickel Cobalt Aluminum Oxide*
LiFePO4 LiNiMnCoO2 (10–20% Co)
LiNiCoAlO2 （9% Co)
LFP
various application.
5. Low Maintenance - no periodic discharge is needed;
there is no memory.
6. Wide variety of shapes and sizes . 7. Components are environmentally safe as there is
ium-Ion Battery
莫乔铃
CONTENTS
1
History Introduction
Application
2 3
1.History
In 1799, Italian physicist Alessandro Volta created the first battery.
In 1859, the first rechargeable battery was the lead acid invented by Gaston Planté. In 1979, John Goodenough demonstrated a rechargeable cell with high cell voltage in the 4V range using lithium cobalt oxide (LiCoO2) as the positive electrode and lithium metal as the negative electrode. In 1992, Sony first invented Li-ion battery for consumer electronics.
effective and come in a large variety of sizes.
LiPo cells are constructed by stacking electrode and electrolyte materials in a flat sandwich, rather than by winding
changing on a continuing basis.
The Lithium-Ion battery has three basic shape size: the cylindrical , Prismatic or brickshaped, flat sandwich
The cylindrical 18650 cell
NMC
Li-phosphate
NMC
NCA
NCA
Lithium Titanate *
Li4Ti5O12
LTO
Li-titanate
PP, PE
PMMA, LiClO4, LiPF6, LiAsF6
2.2 Working Principles
Anode：
Cathode：
Advantages
1. High energy density - potential for yet higher
capacities.
2. Relatively low self-discharge. 3. Excellent charge retention. 4. Diversified positive and negative electrodes for
3. Expensive to manufacture - about 40 percent
higher in cost than nickel-cadmium.
4. If a LIB is fully discharged, it gets totally damaged. 5. Not fully mature - metals and chemicals are