汽车模具专业术语
模具专业术语大全(K12教育文档)
模具专业术语大全(word版可编辑修改)编辑整理：尊敬的读者朋友们：这里是精品文档编辑中心，本文档内容是由我和我的同事精心编辑整理后发布的，发布之前我们对文中内容进行仔细校对，但是难免会有疏漏的地方，但是任然希望（模具专业术语大全(word版可编辑修改)）的内容能够给您的工作和学习带来便利。
同时也真诚的希望收到您的建议和反馈，这将是我们进步的源泉，前进的动力。
本文可编辑可修改，如果觉得对您有帮助请收藏以便随时查阅，最后祝您生活愉快业绩进步，以下为模具专业术语大全(word版可编辑修改)的全部内容。
模具专业术语大全模具零件英语词汇punch冲头insert入块(嵌入件）deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch =stinger 加强筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板ribbon punch压筋冲子模具模板英语词汇top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板（底板）stripping plate内外打（脱料板）outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板cover plate盖板模具五金零件英语词汇inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq—height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模具冲压英语词汇extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量模具工程类英语词汇模具专业术语大全(word版可编辑修改)plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi—shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印模具厂常用标准零配件英语词汇air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate角形模板finish machined roundplate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块模具专业术语大全(word版可编辑修改)locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板×××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××。
常用模具术语
常用模具术语出模：啤件在顶出机构的作用下离开模具的过程啤把：出模角度或者出模斜度倒扣：因为侧面角度或凹位而无法垂直出模的位置排模：模具的排期正哥：型腔在上模，型芯在下模的一种模具结构反哥：型心在上模，型腔在下模的一种模具结构分型：把产品分为上下模的过程种针：基准针，配针时以此针为基准放样：胶样的比例放大复样：胶样的复制调面：在雕刻时，调整胶样表面与要加工表面平行的过程摆斜雕刻：在雕刻时，因有些面不易加工，把胶样摆成一定角度的加工方法顶针出柱：用顶针的顶面来封住成型柱的底面，而使柱成型顶针包针：顶针过长或配针不当，而使顶针包在产品内锅柱：柱的前端有一锥型孔，上大下小，起到铆钉的作用。
多用于压铸模镶针出柱：用镶针的顶面来封住成型柱的底面，而使柱成型镶针出孔：用镶针成型孔原身出：用内模加工出要成型的形状来成型的方法大水口：二板模入水水塘：啤件为透明件或要求变形较小的薄壁件入水时，采用在浇口与流道间所加的一段起到缓冲作用的位置方法，这个缓冲位置就是入水水塘磨角尺：用磨床磨直角锣正：用铣床铣平面或直角Fit平面：用打磨机把平面精加工到要求的配合公差范围Fit枕位：用打磨机把枕位精加工到要求的配合公差范围Fit行位：用打磨机把行位精加工到要求的配合公差范围Fit插穿：用打磨机把插穿位精加工到要求的配合公差范围面镶：镶件从内模的上表面镶入一定的深度，不可到底面，下面用螺丝固定通镶：镶件从内模的下面镶入，直达上表面，通过整个内模兜底镶：镶件从内模的下面镶入，直达上表面，通过整个内模，在镶件下面以台阶形式固定侧镶：镶件从侧面镶入，一般多用在行位上奔子孔：胶样上的一个基准孔，所有的位置都要从这个孔取数镗蚀：铜公水平运动加工照数：用中心镜对要加工部位进行坐标值确定打盲孔：用电火花加工盲孔损公：损耗的铜公积碳：EDM加工时产生的碳堆积在零件或铜公上，使被加工的零件的平面凹凸不平粗公：粗加工时使用的铜公，火花间隙一般为单边0.25幼公：精加工时使用的铜公，火花间隙一般为单边0.07暴公：比粗公火花间隙还要大的铜公，用与粗加工立体公：一个整体铜公，形状与整个上模或这个下模相同清角铜公：对有些直角部位，因CNC不能完全加工而留有余量。
50个模具专业术语
50个模具专业术语1. 模具 (Mold)2. 塑料模具 (Plastic Mold)3. 金属模具 (Metal Mold)4. 注塑机 (Injection Molding Machine)5. 压铸机 (Die Casting Machine)6. 打磨 (Polishing)7. 铣削 (Milling)8. 钳工 (Machining)9. 精雕 (Engraving)10. 焊接 (Welding)11. 冲压 (Stamping)12. 切割 (Cutting)13. 合模 (Closing)14. 分模 (Opening)15. 导柱 (Guide Pillar)16. 导套 (Guide Bush)17. 滑块 (Slider)18. 塑料件 (Plastic Part)19. 金属件 (Metal Part)20. 模仁 (Core)21. 模腔 (Cavity)22. 底座 (Base)23. 热流道 (Hot Runner)24. 冷却系统 (Cooling System)25. 泵箱 (Pump Box)26. 压缩机 (Compressor)27. 水力缸 (Hydraulic Cylinder)28. 模具钢 (Mold Steel)29. 法兰 (Flange)30. 注塑模具 (Injection Mold)31. 放电加工 (Electrical Discharge Machining)32. 模仁巧妙 (Core Pull)33. 螺旋通道 (Spiral Channel)34. 冷却塔 (Cooling Tower)35. 酸洗 (Acid Etching)36. 布胶 (Rubberizing)37. 文字标记 (Texturing)38. 研磨剂 (Polishing Compound)39. 硅胶 (Silicone)40. 硬度测试 (Hardness Testing)41. 射出速度 (Injection Speed)42. 模具寿命 (Mold Life)43. 热流道系统 (Hot Runner System)44. 冷却时间 (Cooling Time)45. 模具设计 (Mold Design)46. 模具制造 (Mold Manufacturing)47. 模具修理 (Mold Repair)48. 模具改造 (Mold Modification)49. 模具试模 (Mold Trial)50. 模具测试 (Mold Testing)。
模具英语专业术语
模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。
L：分模线EJECT PIN/E。
P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：淬火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩水DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期注塑英语型厚大小Thick size锁模结构（机绞/直压）Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式（电动五点，油压五点，油压十三点）Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质（合金）Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量（理论）Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式（全自动/全液压）Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程，open ould stroke定产，order production定产效率，efficiency of order prod uction注胶切换点，glue-injection switching point保压压力1，protective pressure倒索，inverse sling模保护，mould protection关模低压，close mould low pressure炮筒温度，gun barrel temperature回料量，returning amount注射压力，injecting pressure色母配比，raw color ratio mixing配套摸具，matched mold顶针次数，thimble times立式注胶机vertical injector工艺卡，WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in e xtra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模：Injection mould热塑性塑料注射模：Injection mould for thermoplasctics 热固性塑料注射模：Injection mould for thermosets无流道模：Runerless mould热流道模：Hot runner mould绝热流道模：Insulated温流道模：Warm runner mould2. 浇注，排溢，分型浇注系统：Feed system主流道：Sprue分流道：Runner浇口：Gate直接浇口：Direct gate ;Sprue gate环行浇口：Ring gate盘型浇口：Disk gate ;Diaphragm轮辐浇口：Spoke gate :Spider gate点浇口：Pin-point gate侧浇口：Edge gate潜伏浇口：Submarine gate护耳浇口：Tab gate扇型浇口：Fan gate 牛角浇口：Horn gate冷料穴：Cold-slug well浇口套：Sprue bush ;Sprue bushing浇口镶块：Gating insret分流锥：Sprader流道板：Runner plate热流道板：Manifold block;Hot-runner manifold温流道板：Warm runner plate二级喷嘴：Secondary nozzle鱼雷形组合体：Torpedo;T orpedo body assembly管式加热器：Cartridge heater热管：Heat pipe阀式浇口：Valve gate加热腔：Loading chamber柱塞：Force plunger;Pot plungr溢料槽：Flash grorve ;Spew grovve排气槽：Vent分型面：Parting line水平分型面：Horizontal parting half垂直分型面：Vertical parting half3. 成型零件定模：Stationary mould:Fixed half动模；Movable mould ;Moving half上模:Upper mould;Upper half下模：Lower mould :Lower half型腔：Cavity凹模：Impression;Cavity plate镶件：Mould insert活动镶件：Movable insert;Lose detail拼块：Splits凹模拼块：Cavity splits型芯拼块：Core splits型芯：Core侧型芯：Side core:slide core螺纹型芯：Thread plug;Threaded core螺纹型环：Thread ring;Threaded cavity凸模：Punch;Force嵌件：Insert for mould4. 支持与固定零件定模座板：Fixed clamp plate:Top clamping plate;Top plate动模座板：Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板：Upper clamping plate下模座板：Lower clamping plate凹模固定板：Cavity-retaier plate型芯固定板：Core-retaier plate凸模固定板：Punch-retaier pilte模套：Chase ;Bolster;Frame;支撑板：Backing plate垫块：Spacer parallel支架：Ejector housing支撑柱：Support pillar模板：Mould plate5. 抽芯零件斜销：Angle pin; Finger cam滑块：Slide;Cam slide侧型芯滑块：Slide core-slide滑块导板：Slide guide strip锲紧块：Heel block;Wedge block;Locking heel斜槽导板：Finger guide plate弯销：Dog-leg cam斜滑块：Angled-lift splits6. 导向零件导柱：Guide pillar;Guide pin;Leader pin带头导柱：Guide pillar ;Straight leader pin带肩导柱：Guide pillar Shouldered;Shoulder leader pin推板导柱：Ejector guide pillar;Ejeector guide pin导套：Guide bush ;Guide bushing直导套：Guide bush ;Straight ;Straight bushing带头导套：Guide bush ;Shoulder bushing推板导套：Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈：Locating ring锥形定位圈：Mould bases locating elements复位杆：Ejector plate return pin;Push-back pin限位钉：Stop pin;Stop button限位块：Stop block ;Stop pad定距拉杆：Length bolt;Puller bolt定距拉板：Puller plate;Limit plate8. 推出零件推杆：Ejector pin圆柱头推杆：Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管：Ejector sleeve推块：Ejector pad推件板：Stripper plate推件环：Stripper ring;Stripper dlisk推杆固定板：Ejector retainer plate推板：Ejector plate;Ejection plate连接推杆：Ejector tie rod 拉料杆：Sprue puller钩形垃料杆：Sprue puller ;Z-shaped球头垃料杆：Sprue puller;Ball headed圆锥头垃料杆：Sprue puller;Conical headed分流道垃料杆：Runner puller;Runner lock pin推流道板：Runner stripper plate9. 冷却和加热零件冷却通道：Cooling channel;Cooling line隔板：Baffle加热板：Heating plate隔热板：Thermal insulation board10. 模架模架：Mould base标准模架：Standard mould base11. 塑料成型模具的主要设计要素注射能力：Shot capacity收缩率：Shrinkage注射压力：Injection pressure锁模力：Clamping force ;Locking force成型压力：Moulding pressure模内压力：Internal mould pressure;Cavity pressure开模力：Mould opening force脱模力：Ejection force抽芯力：Core-pulling force抽芯距：Core-pulling distance闭合高度：Mould shut height最大开距：Maximum daylight;Open daylight投影面积：Projected area脱模斜度：Draft脱模距：Stripper distance教你如何用WORD文档(2012-06-27 192246)转载▼标签：杂谈1. 问：WORD 里边怎样设置每页不同的页眉？如何使不同的章节显示的页眉不同？答：分节，每节可以设置不同的页眉。
汽车模具零件术语
工作原理：通过斜楔机 构的运动，实现对模具 零件的夹紧和松开，同 时保证定位精度。
应用范围：广泛应 用于汽车模具、注 塑模具等精密模具 领域。
优点：结构简单、 紧凑，操作方便， 能够实现快速准确 的定位和夹紧。
定义：滑块是在模具中能够进行滑 动配合，实现模具零件的精确加工 和定位的部件。
结构：滑块一般由导轨和滑块本体 组成，导轨用于滑块的导向和定位， 滑块本体则用于安装模具零件。
作用：热处理可以改善金属材料的加 工性能、提高其硬度和耐磨性，同时 还可以提高其抗腐蚀性能和疲劳强度。
添加标题
添加标题
添加标题
添加标题
分类：根据加热温度和冷却方式的 不同，热处理可分为多种类型，如 退火、淬火、回火等。
工艺要求：热处理工艺要求严格控制 加热温度、保温时间和冷却速度等参 数，以确保获得所需的内部结构和机 械性能。
XX,a click to unlimited possibilities
汇报人：XX
CONTENTS
PART ONE
PART TWO
按制造方式分类：铸造件、 锻造件、机加工件
按功能分类：成型零件、结 构零件、辅助零件
按材料分类：金属件、非金 属件
按模具结构分类：单件式、 组合式
模具零件是制造汽车模具的基础，其作用是保证模具的精度和稳定性。
作用：侧型芯主要承受侧向压力和侧向型腔的成型力，确保汽车侧向孔或侧向凸台的尺 寸和形状精度。
结构形式：侧型芯通常采用模块化设计，由多个拼块组成，方便组装和维修。
材料选择：侧型芯一般采用高强度钢材或硬质合金材料制造，以确保其耐磨性和耐久性。
定义：斜楔机构是一 种用于汽车模具零件 的特殊机构，用于实 现精确的定位和夹紧。
模具专业英文术语大全
模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车（AGV）57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控（CNC）机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。
汽车制造行业专业术语
汽车制造行业专业术语汽车制造行业是一个涉及众多复杂工艺和技术的领域，因此拥有大量专业术语。
以下是一些汽车制造行业中的关键专业术语的详细介绍：1.汽车平台：1.定义：汽车平台指的是一组共享的基础设计、工程元素和组件，这些可以在多个车型中重复使用。
2.作用：通过平台化策略，汽车制造商可以降低生产成本，加快新车上市时间，并提高不同车型之间的零部件通用性。
2.冲压工艺：1.定义：冲压是将金属板材通过模具冲压成特定形状的过程，用于制造车身的外部覆盖件和结构件。
2.工艺过程：包括落料、冲孔、弯曲、拉伸等步骤，通常使用大型冲压机和精密模具来完成。
3.焊接工艺：1.定义：焊接是将两个或更多金属部件连接在一起的方法，通过熔化部件的接口并使用填充材料来形成永久性的结合。
2.类型：汽车制造中常用的焊接方法包括电阻点焊、激光焊接和MIG/MAG焊接等。
4.涂装工艺：1.定义：涂装是指将液态涂料（如油漆）均匀地涂覆在汽车表面，形成具有装饰性和保护性的涂层。
2.过程：包括预处理（如除锈、磷化）、电泳底漆、中涂和面漆等步骤，通常在自动化喷涂线和烘干室中完成。
5.总装工艺：1.定义：总装是将所有零部件和子系统组装成一辆完整汽车的最后阶段。
2.过程：包括发动机和底盘的合装、内饰装配、座椅安装、线束连接以及最终的质检和调试等步骤。
6.动力总成：1.定义：动力总成是指汽车中负责产生动力的部分，通常包括发动机和变速器。
2.分类：根据燃料类型，发动机可分为汽油机、柴油机等；根据动力来源，还有电动机和混合动力系统等。
7.底盘系统：1.定义：底盘是汽车的基础结构，支撑着车身和其他所有部件，并传递来自路面的各种力和扭矩。
2.组成：包括悬架系统、转向系统、制动系统和传动系统等关键子系统。
8.车身电子控制系统（EECS）：1.定义：EECS负责管理和监控车辆中的各种电子设备，确保它们正常工作并相互通信。
2.功能：包括发动机管理、车身控制（如灯光、门锁）、驾驶辅助系统（如ABS、ESP）以及信息娱乐系统等。
汽车零部件生产术语
汽车零部件生产术语
1. 冲压成形(Stamping)
这是一种通过将金属板材置于模具中,施加巨大压力将其塑形成所需零件的制造工艺。
常见的冲压件包括车身面板、底盘部件等。
2. 铸造(Casting)
通过将熔融金属或合金浇注到模具腔内,冷却凝固成型的制造过程。
常见的铸造件包括发动机缸体、变速箱壳体等。
3. 锻造(Forging)
在加热状态下,将金属坯料置于模具中经受重击或挤压力而成形的工艺。
常见的锻件包括曲轴、连杆等。
4. 机加工(Machining)
利用切削加工设备如车床、铣床等,将金属坯料切削成所需形状和尺寸的制造方式。
常用于加工发动机零件、变速箱零件等。
5. 焊接(Welding)
利用热或压力将两个或多个金属零件连接在一起的过程。
焊接方式包括电弧焊、点焊、激光焊等,广泛应用于车身结构、排气系统等。
6. 热处理(Heat Treatment)
通过对金属零件进行加热、保温和冷却等热处理,以改善其机械性能的工艺过程。
如调质热处理可提高强度和硬度。
7. 表面处理(Surface Treatment)
对金属零件表面进行电镀、喷涂、氧化等处理,以提高耐腐蚀性、装饰性等特性的工艺过程。
如电镀铬、阳极氧化等。
以上是汽车零部件生产中常见的一些术语和概念,掌握这些可以更好地理解汽车制造过程。
模具专业术语
模具专业术语模具述语⼀、⼊⽔：gate撑头: support pillar进⼊位：gate location唧嘴：sprue bushing⽔⼝形式：gate type挡板：stop plate⼤⽔⼝：edge gate定位圈：locating ring细⽔⼝：pin-point gate锁扣：latch⽔⼝⼤⼩：gate size扣鸡：Parting lock set转⽔⼝：Switching runner/gate 推杆：push bar唧嘴⼝径：sprue diameter栓打螺丝：S.H.S.B⼆、流道: runner顶板：ejector rod热流道：hot runner,hot manifold 活动臂：lever arm热嘴冷流道: hot sprue/cold runner 分流锥：spure sperader 唧嘴直流: direct sprue gate⽔⼝司:bush圆形流道：round(full/half runner 垃圾钉：stop pin流道电脑分析：mold flow analysis 隔⽚：buffle流道平衡:runner balance弹⼸柱：spring rod热嘴：hot sprue弹⼸:die spring热流道板：hot manifold中托司：ejector guide bush发热管：cartridge heater中托边：ejector guide pin探针: thermocouples插头：connector plug销⼦：dowel pin插座：connector socket波⼦弹⼸：ball catch密封/封料：seal喉塞: pipe plug三、运⽔：water line锁模块：lock plate喉塞：line lpug斜顶：angle from pin喉管：tube斜顶杆：angle ejector rod塑胶管：plastic tube尼龙拉勾：parting locks快速接头：jiffy quick connector plug/socker活动臂：lever arm四、模具零件：mold components复位键、提前回杆：early return bar三板模：3-plate mold⽓阀：valves⼆板模：2-plate mold斜导边：angle pin边钉/导边：leader pin/guide pin术语：terms边司/导套：bushing/guide bushing承压平⾯平衡：parting surface support balance 中托司：shoulder guide bushing模排⽓：parting line venting中托边L：guide pin回针碰料位：return pin and cavity interference 顶针板：ejector retainner plate模总⾼超出啤机规格：mold base shut hight托板：support plate顶针碰运⽔：water line interferes withejector pin料位出上/下模：part from cavith (core) side管钉：dowel pin模胚原⾝出料位：cavity direct cut on A-plate,core direct cut on B-plate. 开模槽：ply bar scot 不准⽤镶件：Do not use (core/cavity) insert内模管位：core/cavity inter-lock⽤铍铜做镶件：use beryllium copper insert顶针：ejector pin初步（正式）模图设计：preliinary (final) mold design司筒：ejector sleeve反呵：reverse core司筒针：ejector pin弹⼸压缩量：spring compressed length推板：stripper plate稳定性好：good stability,stable缩呵：movable core,return core core puller 强度不够：insufficient rigidity扣机（尼龙拉勾）：nylon latch lock均匀冷却：even cooling斜顶：lifter扣模：sticking模胚（架）：mold base热膨胀：thero expansion上内模：cavity insert公差：tolorance下内模：core insert铜公(电极）：copper electrode⾏位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate。
模具专业术语
模具专业术语Layout安排图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一路fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair补缀operator功课员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外不雅检查inner parts inspect内部检查thumb screw大年夜头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制做功课法度榜样material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资本部production department临盆部分planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down萌芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity临盆力education and training教诲与练习proposal improvement提案改良spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部分名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大年夜拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack起落机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺点critical defect极严峻缺点major defect重要缺点minor defect次要缺点not up to standard不合规格dimension/size is a little bigger尺寸偏大年夜(小)cosmetic defect外不雅不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大年夜grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事宜不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing别处处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安稳quality品德delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce临盆equipment设备to start a press开机stop/switch off a press关机classification整顿regulation整顿cleanness清扫conservation洁净culture教化qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing紧缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特点变革evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造治理abnormal handling专门处理production unit临盆单位lots of production临盆批量steel plate钢板roll material卷料manufacture procedure制程operation procedure功课流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation主动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上逝世点bottom stop下逝世点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration挂号registration card挂号卡to control管束to put forward and hand in提报safe stock安稳库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消费to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card体会卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for dieengineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变更die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder材料夹to put file in order整顿材料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在成品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count管帐师盘,点数量the first page第一联filed by accounting department for reference管帐部存查end-user/using unit(department)应用单位summary of year-end physicalinventory bills年关盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一路送管帐部(NHK厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年关盘点卡与清册应用状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing 工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决定事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheetPCE组装厂临盆排配表model机锺work order工令revision版次remark备注production control confirmation临盆确认checked by初审approved by核准department部分stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可应用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description缘故说明part number/ P/N 料号type形状item/group/class类别quality品德prepared by制表notes说明year-end physical inventory difference analysis sheet年关盘点差别分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差别量cause analysis缘故分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability才能parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报宁神品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction关心功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔情势voller pin formality滚针情势cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度误差velocity速度production tempo临盆进度近况torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破裂机模具工程类plain die简略单纯模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside不和压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具构造图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range有用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板顶板top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate表里打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中心板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相干英文compre sion molding紧缩成型flash mold溢流式模具plsitive mold挤压式模具split mold瓜分式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式模具well type蓄料井insulated runner绝缘浇道方法hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)成型机顶业捧subzero深冷处理three plate三极式模具runner system浇道体系stress crack应力电裂orientation定向sprue gate射料浇口直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate裂缝浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔阂浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate地道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方法long nozzle延长喷嘴方法sprue浇口;溶渣品德人员名称类QC quality control 品德治理人员FQC final quality control 终点品质管束人员IPQC in process quality control制程中的品德管束人员OQC output quality control 最终出货色质管束人员IQC incoming quality control 进料品德管束人员TQC total quality control 周全质量治理POC passage quality control 段检人员QA quality assurance 质量包管人员OQA output quality assurance 出货质量包管人员QE quality engineering 品德工程人员品德包管类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认申报3B 3B 模具正式投产前确认CP capability index 才能指数CPK capability index of process 模具制程才能参数SSQA standardized supplier quality 合格供给商品德评估OOBA out of box audit 开箱检查QFD quality function deployment 品德机能展开FMEA failure model effectiveness analysis 掉效模式分析8 disciplines 8项答复内容FA final audit 最後一次考察CAR corrective action request 改正行动要求corrective action report 改正行动申报FQC运作类AQL Acceptable Quality Level 运作类允收品德水准S/S Sample size 抽样考查样本大年夜小ACC Accept 允收REE Reject 拒收CR Critical 极严峻的MAJ Major 重要的MIN Minor 略微的AOQ Average Output Quality 平均出厂品德AOQL Average Output QualityLevel 平均出厂品德Q/R/S Quality/Reliability/Service品德/靠得住度办事MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 专门抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查申报FPIR First Piece Inspection Report百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管束SQC Statistical Quality Control 统计品德管束R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管束上限LCL Lower Central Limit 管束下限MAX Maximum 最大年夜值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性确信量靠得住与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品德术语类QCC Quality Control Circle 品德圈QIT Quality Improvement Team 品质改良小组PDCA Plan Do Check Action 筹划履行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品德改良QP Quality Policy 目标方针TQM Total Quality Management 周全品德治理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品德水准RMA Return Material Audit 退料承认QAN Quality Amelionrate Notice 品德改良活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品德目标7QCTools 7 Quality Controll Tools 品管七大年夜手段通用之件类ECN Engineering Change Notes 工程变革通知(供给商)ECO Engineering Change Order 工程修改要求(客户)PCN Process Change Notice 工序修改通知PMP Product Management Plan 生产管束筹划SIP Specification In Process 制程考查规格SOP Standard Operation Procedure 制做功课规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面体系文件类QC Quality System 品德体系ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大年夜陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一样规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制做功课规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管功课规范CQCP P-Painting Compaq产品在龙华烤漆厂品管功课规范部类PMC Production & MaterialControl 临盆和物料操纵PPC Production Plan Control 临盆筹划操纵MC Material Control 物料操纵ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 管帐部P/A Personal & Administration 人事行政部DC Document Center 资估中间QE Quality Engineering 品德工程(部)QA Quality Assurance 品德包管(处) QC Quality Control 品德管束(课) PD Product Department 临盆部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂) 临盆类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 临盆单D/C Date Code 临盆日期码ID/C Identification Code (供给商) 辨认码SWR Special Work Request 专门工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal Computer Enclosure小我电脑外设PC Personal Computer 小我电脑CPU Central Processing Unit 中心处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大年夜陆PRC People's Republic of China中国大年夜陆U.S.A the United States of America美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不有用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不可,不合格C=0 Critical=0 极严峻不许可ESD Electry-static Discharge 静电排放5S 希腊语整顿,整顿,清扫,洁净, 教化A TIN Attention 知会CC Carbon Copy 副本复印相干人员APP Approve 核准,承认,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下昼CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 运算机关心设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时刻(临盆前预备时刻)S/T Standard Time 标准时刻P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 花费性电子5WIHWhen,Where,Who,What,Why,How to 5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技巧,时刻(资本) SQA Strategy Quality Assurance 策略品德包管DQA Desigh Quality Assurance 设计品德包管MQA Manufacture Quality Assurance 制造品德包管SSQA Sales and service Quality Assurance 发卖及办事品德包管LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
组装、冲压、喷漆等专业词汇punching machine 冲床Tiana天那水thumb大拇指robot机械手cleaning cloth抹布forefinger食指Assembly line组装线hydraulic machine油压机to load material上料midfinger中指Layout布置图lathe车床to unload material卸料ring finger无名指Screw driver起子miller铣床to return material/stock to退料little finger小指Electric screw driver电动起子grinder磨床scraped报废band-aid创可贴Pneumatic screw driver气动起子driller钻床scrape ..v.刮;削industrial alcohol工业酒精worktable 工作桌linear cutting线切割oxidation |n|氧化sweeper扫把fit together组装在一起electrical sparkle电火花scratch刮伤mop拖把fasten锁紧(螺丝)welder电焊机dents压痕rag 抹布fixture 夹具(治具)position职务embedded lump镶块garbage container灰箕repair修理president董事长production capacity生产力garbage can垃圾箱operator作业员general manager总经理proposal improvement提案改善garbage bag垃圾袋QC品管special assistant manager特助spare parts=buffer备件chain链条supervisor 课长factory director厂长forklift叉车jack升降机chassis基座department director部长trailer=long vehicle拖板车production line流水线power button电源按键deputy manager | =vice manager副理compound die合模air pipe 气管sheet metal parts 冲件section supervisor课长die locker锁模器packaging打包SOP制造作业程序group leader/supervisor组长pressure plate=plate pinch压板major defect主要缺陷material check list物料检查表line supervisor线长bolt螺栓minor defect次要缺陷work cell工作间assistant manager助理automatic screwdriver电动启子dimension尺寸carton纸箱to move, to carry, to handle搬运thickness gauge厚薄规cosmetic defect外观不良left fork叉车be put in storage入库gauge(or jig)标准尺v.测量speckle斑点personnel resource department人力资源部pack packing包装power wire电源线mildewed=moldy=mouldy发霉production department生产部门to apply oil擦油pedal踩踏板rust生锈planning department企划部to file burr 锉毛刺flow board流水板deformation变形QC Section品管科final inspection终检hydraulic handjack油压板车polishing/surface processing表面处理stamping factory冲压厂to connect material接料glove(s)手套safety安全common equipment常用设备to reverse material 翻料glove(s) with exposed fingers割手套quality品质delivery deadline交货期punch press, dieing out press冲床statistics统计distribution department分发单位cost成本feeder送料机demand and supply需求chairman主席engineering工程rack, shelf, stack料架to take apart a die卸下模具present members出席人员classification整理cylinder油缸to load a die装上模具subject主题regulation整顿conveyer belt输送带easily damaged parts易损件conclusion结论cleanness清扫top stop上死点standard parts标准件decision items决议事项conservation清洁bottom stop下死点breaking.(be)broken,(be)cracked 断裂responsible department负责单位culture教养one stroke一行程to lubricate润滑pre-fixed finishing date预定完成日waste废料reset复位figure file, chart file图档work order工令sliding rack滑料架smoothly顺利progressive die,follow die连续模remark备注to fix a die装模filings铁削compound die复合模checked by初审to take apart a die拆模to stock, storage, in stock库存panel board镶块approved by核准transportation运输o draw holes抽孔design modification设计变化on-hand inventory现有库存up to grade合格receive领取sliding block滑块total合计not up to grade, not qualified不合格approval examine and verify审核location pin定位销item/group/class类别evaluation评估processing, to process加工lifting pin顶料销prepared by制表prepare for, make preparations for 准备delivery, to deliver 交货padding block垫块notes说明parameters参数to retrn of goods退货spare dies模具备品cause analysis原因分析manufacture management制造管理registration登记document folder文件夹finished product成品production unit生产单位safe stock安全库存file folder资料夹semi-finished product半成品lots of production生产批量acceptance = receive验收to put file in order整理资料warehouse/hub仓库steel plate钢板to notice通知equipment设备wire EDM线割roll material卷料application form for purchase请购单waste materials废料EDM放电机operation procedure作业流程consume, consumption消耗bill name单据名称coil stock卷料automation自动化to fill in填写plate电镀tolerance公差shut die架模abrasion磨损material for mold testing试模材料radius半径shut height of a die架模高度reverse angle = chamfer倒角sample样品torch-flame cut火焰切割冲压常词汇to collect, to gather收集meeting minutes会议记录under cut=scrap chopper清角stamping, press冲压failure, trouble故障location地点air-cushion eject-rod气垫顶杆bushing block 衬套lifter pin 顶料销quenching crack 淬火裂痕buffing 抛光insert 镶块outer bush 外导套quenching distortion 淬火变形edge file 刃用锉刀capability 能力stamped punch 字模冲子quenching stress 淬火应力file 锉刀factor 系数round punch 圆冲子rust prevention 防蚀grinder 砂轮机rack 上料special shape punch 异形冲子softening 软化退火lapping 研磨flow chart 流程表单located block 定位块relieving annealing 应力消除退火metal saw 金工锯assembly 组装air cushion plate 气垫板surface hardening 表面硬化处理polisher 磨光器coordinate 座标air-cushion eject-rod 气垫顶杆vacuum hardening 真空淬火protable driller 手提钻孔机derusting machine 除锈机QC quality control 品质管理人员hand face shield 手握面罩sand paper 砂纸dryer 烘干机QE quality engineering 品质工程人员hard facing 硬表面堆焊spanner 扳手concave 凹QA quality assurance 质量保证人员laser beam welding 雷射光焊接tosecan 划线盘convex 凸overlaying 堆焊scrap cutter 废料切刀nick 缺口cell 气孔slug hole 逃料孔augular offset 角度偏差lubricant 润滑剂assembly drawing 装配图velocity 速度center buckle 表面中部波皱fit tolerance 配合公差production tempo 生产进度现状check 细裂痕hatching 剖面线quenching 水淬火checking 龟裂account 帐户tempering 回火5S 希腊语 整理,整顿,清扫,清洁,教养crack 裂痕after service 售后服务annealing 退火3D coordinate measurement 三次元量deformation 变形cheque 支票carbonization 碳化cylindrical grinding machine 外圆磨flange wrinkle 凸缘起皱cost 成本alloy 合金feeler gauge 测隙规gloss 光泽customer 客户coolant 冷却液nonius 游标卡尺scrap 废料deferred payment 分期付款material thickness 料片厚度passimeter 内径仪scrap jam 废料阻塞enclosure 附件press specification 冲床规格square master 直角尺skin inclusion 表皮摺叠invoice 发票gap 间隙forging die steel 锻造模用钢 torsion 扭曲payment method 付款方式weight 重量flame hardening 火焰硬化warpage 翘曲request letter 请求函total wt.总重量heat treatment 热处理weld mark 焊痕subcontract 外包inner guiding post 内导柱metallizing 真空涂膜wrinkle 皱纹wharf 码头outer guiding post 外导柱hardening 淬火angle cutter 角铣刀FMEA failure model effectiveness analysis 失效模式分析ADM Absolute Dimension Measuremat 全尺寸测量PRC People's Republic of China 中国大陆。