模具专业术语大全
模具专业术语大全(K12教育文档)
模具专业术语大全(word版可编辑修改)编辑整理：尊敬的读者朋友们：这里是精品文档编辑中心，本文档内容是由我和我的同事精心编辑整理后发布的，发布之前我们对文中内容进行仔细校对，但是难免会有疏漏的地方，但是任然希望（模具专业术语大全(word版可编辑修改)）的内容能够给您的工作和学习带来便利。
同时也真诚的希望收到您的建议和反馈，这将是我们进步的源泉，前进的动力。
本文可编辑可修改，如果觉得对您有帮助请收藏以便随时查阅，最后祝您生活愉快业绩进步，以下为模具专业术语大全(word版可编辑修改)的全部内容。
模具专业术语大全模具零件英语词汇punch冲头insert入块(嵌入件）deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch =stinger 加强筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板ribbon punch压筋冲子模具模板英语词汇top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板（底板）stripping plate内外打（脱料板）outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板cover plate盖板模具五金零件英语词汇inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq—height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模具冲压英语词汇extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙punch wt.上模重量模具工程类英语词汇模具专业术语大全(word版可编辑修改)plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi—shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印模具厂常用标准零配件英语词汇air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate角形模板finish machined roundplate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块模具专业术语大全(word版可编辑修改)locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板×××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××。
常用模具术语
常用模具术语出模：啤件在顶出机构的作用下离开模具的过程啤把：出模角度或者出模斜度倒扣：因为侧面角度或凹位而无法垂直出模的位置排模：模具的排期正哥：型腔在上模，型芯在下模的一种模具结构反哥：型心在上模，型腔在下模的一种模具结构分型：把产品分为上下模的过程种针：基准针，配针时以此针为基准放样：胶样的比例放大复样：胶样的复制调面：在雕刻时，调整胶样表面与要加工表面平行的过程摆斜雕刻：在雕刻时，因有些面不易加工，把胶样摆成一定角度的加工方法顶针出柱：用顶针的顶面来封住成型柱的底面，而使柱成型顶针包针：顶针过长或配针不当，而使顶针包在产品内锅柱：柱的前端有一锥型孔，上大下小，起到铆钉的作用。
多用于压铸模镶针出柱：用镶针的顶面来封住成型柱的底面，而使柱成型镶针出孔：用镶针成型孔原身出：用内模加工出要成型的形状来成型的方法大水口：二板模入水水塘：啤件为透明件或要求变形较小的薄壁件入水时，采用在浇口与流道间所加的一段起到缓冲作用的位置方法，这个缓冲位置就是入水水塘磨角尺：用磨床磨直角锣正：用铣床铣平面或直角Fit平面：用打磨机把平面精加工到要求的配合公差范围Fit枕位：用打磨机把枕位精加工到要求的配合公差范围Fit行位：用打磨机把行位精加工到要求的配合公差范围Fit插穿：用打磨机把插穿位精加工到要求的配合公差范围面镶：镶件从内模的上表面镶入一定的深度，不可到底面，下面用螺丝固定通镶：镶件从内模的下面镶入，直达上表面，通过整个内模兜底镶：镶件从内模的下面镶入，直达上表面，通过整个内模，在镶件下面以台阶形式固定侧镶：镶件从侧面镶入，一般多用在行位上奔子孔：胶样上的一个基准孔，所有的位置都要从这个孔取数镗蚀：铜公水平运动加工照数：用中心镜对要加工部位进行坐标值确定打盲孔：用电火花加工盲孔损公：损耗的铜公积碳：EDM加工时产生的碳堆积在零件或铜公上，使被加工的零件的平面凹凸不平粗公：粗加工时使用的铜公，火花间隙一般为单边0.25幼公：精加工时使用的铜公，火花间隙一般为单边0.07暴公：比粗公火花间隙还要大的铜公，用与粗加工立体公：一个整体铜公，形状与整个上模或这个下模相同清角铜公：对有些直角部位，因CNC不能完全加工而留有余量。
50个模具专业术语
50个模具专业术语1. 模具 (Mold)2. 塑料模具 (Plastic Mold)3. 金属模具 (Metal Mold)4. 注塑机 (Injection Molding Machine)5. 压铸机 (Die Casting Machine)6. 打磨 (Polishing)7. 铣削 (Milling)8. 钳工 (Machining)9. 精雕 (Engraving)10. 焊接 (Welding)11. 冲压 (Stamping)12. 切割 (Cutting)13. 合模 (Closing)14. 分模 (Opening)15. 导柱 (Guide Pillar)16. 导套 (Guide Bush)17. 滑块 (Slider)18. 塑料件 (Plastic Part)19. 金属件 (Metal Part)20. 模仁 (Core)21. 模腔 (Cavity)22. 底座 (Base)23. 热流道 (Hot Runner)24. 冷却系统 (Cooling System)25. 泵箱 (Pump Box)26. 压缩机 (Compressor)27. 水力缸 (Hydraulic Cylinder)28. 模具钢 (Mold Steel)29. 法兰 (Flange)30. 注塑模具 (Injection Mold)31. 放电加工 (Electrical Discharge Machining)32. 模仁巧妙 (Core Pull)33. 螺旋通道 (Spiral Channel)34. 冷却塔 (Cooling Tower)35. 酸洗 (Acid Etching)36. 布胶 (Rubberizing)37. 文字标记 (Texturing)38. 研磨剂 (Polishing Compound)39. 硅胶 (Silicone)40. 硬度测试 (Hardness Testing)41. 射出速度 (Injection Speed)42. 模具寿命 (Mold Life)43. 热流道系统 (Hot Runner System)44. 冷却时间 (Cooling Time)45. 模具设计 (Mold Design)46. 模具制造 (Mold Manufacturing)47. 模具修理 (Mold Repair)48. 模具改造 (Mold Modification)49. 模具试模 (Mold Trial)50. 模具测试 (Mold Testing)。
模具专业术语
模具专业术语模具专业术语Company Document number：WUUT-WUUY-WBBGB-BWYTT-1982GT模具专业术语——注塑模(锦浩塑胶模具厂）English Training——Injection Mold（一）模具专业基本用词Professional Terms1．塑料—plastic, resin2．样件—sample3．钢料—steel4．注塑机—injection machine, press5．产品—part, product, moulding6．模具—mold, mould, toolA 简易模（样板模）—prototype moldB 量产用模具—production mold 7．三维造型（数模）—model, 3D data8．二维产品图—2D part drawing9．设计—design10．制造—manufacture, build up, construction11．检验—chec k, inspection12．测量—measure, inspection13．修改—change, modify, correction14．工程更改—engineer change15．质量—quality16．数量—quantity17．基准—datum, reference（二）如何解析2D 产品图How to read 2D part drawing一．产品几何Geometry1．点—point2．线（边）—line, edge3．面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．加强筋（骨位）—rib6．孔—hole7．细长的槽—slot8．柱位—boss9．角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharpcorner10．斜度—angle, taper11. 凹槽—recess ,groove二．分模信息Splitting1．分型线—parting line (P/L), splitting line2．主分模方向—main direction, line of draw3．浇口设定—gating三．产品标识Part Identification1．产品名称—part name (P/N)2．产品编号+版本号—part number + revision (Rev.)3．型腔号—cavity number4．材料标记—material symbol5．模具编号—mold number (no.)6．日期印—dating insert, date code7．循环印—cycling code8．公司标志—company logo四．技术要求Specification (Special Requirement)1．项目启动表Kick-off sheet1）项目名称—program name, project name2）产品名称—part name, product name, part description3）产品编号—part number (P/N)4）客户模号—customer mold no.5）项目启动日期— kick off date,start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量—number of cavit ies9）数模文件编号—data file n o.10）注塑材料—resin,plastic, raw material11）收缩率—shrink, shrinkage, shrink factor12）注塑机吨位—molding machine size, injection machine size 13）成型周期—cycle time14）型腔光洁度—cavity polish15）型芯光洁度—core polish16）皮纹（晒纹）—texture, grain17）拔模斜度—draft angle, removal taper18）注塑件颜色及光泽—molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商—manifold manufacturer, manifold supplier 21）浇口位置—gate location / position22）浇口类型—gate type23）产品标识—stamp information, part identification24）特殊要求— special instructions2．产品质量及外观要求Part Quality & Appearance1）尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受（合格）—accept, OK⑧拒绝（不合格）—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2）产品缺陷（较常见）Defects (normal)①缩印—sink mark, shrinkage②飞边—flash, burr③段差—mismatch discrepancy④银丝纹—snake marks, streak⑤弯曲—warpage, distortion⑥打不足（缺料）—short shot⑦熔接线—weld line3．产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4．常用词汇、词组及短语Normal Word, Short Sentence1）单边—per side2）双边—both sides3）加入，添加—add, incorporate4）去除，取消—remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 6）要求，需要—require, need, demand 7）确认—be approved, agreed by …8）允许—permit, allow9）在…范围之内—within10）不可以，不允许，禁止—free from,prevent, avoid11）…，除非有另指—…unless otherwise spe cified12）…或少于—…or less13）自动化运作—automatic operation14）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Bu rrs and discrepancy on the P/L shall be … or less.五．标题栏Title Block1．产品名称—part name2．图纸编号 + 版本号（索引号）—drawing no. + level (index) 3．一般公差[的标准] —general tolerance（三）如何阅读制模标准How to read tooling standard一．模具结构术语Mold Construction TerminologyA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具推高尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness2．定模底板—front plate, top clamping plate, clamp plate, clamping plate 3．定模板—cavity plate, fixed mould plate, A –plate4．动模板—core plate, moving mould plate, B – plate5．支撑板—support plate, backing plate6．模脚—support blocks, rails, risers, spacer block7．顶杆固定板—retaining plate, ejector retaining plate8．顶板—ejector plate9．动模底板—back plate10．导柱—guide pillar, leader pin, guide pin11．导套—guide bush, leader pin bush12．复位杆—return pin, push-back pin13．弹簧—spring14．撑头—support pillar15．推板导柱、导套—ejection guide pin / bush16．挡钉—stop pin, stop button17．站立脚—standing-off pillars18．标牌—plaque scutcheonB．成型零部件moulding components19．型芯—core20．型腔—cavity21．镶针—core pin22．镶块—insert, split23．滑块—slide, sliding split24．斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaft 25．成型顶杆—moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道—sprueb．分流道runner①主分流道—main runner ②二级分流道— branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated．模腔—impressione．冷料井—cold slug wellf．热流道—hot runner2．模具零件mold componentsa．定位圈—locating ring, location ring, register ringb．浇口套—sprue bushc．挡圈—stop ringd．浇口镶块—gate inserte．热流道板—manifoldf．热嘴—hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting1．分型线—parting line ( P/L )2．镶拼线—bodyline, joint line3．平/ 不平的分型面—flat / non – flat parting surface4．封胶面—shut off surfaces, seal-off surfaces5．擦位—shut off6．碰穿位—kiss-off7．管位—parting line lock8．分型面的释放(避空) —relief of parting surface9．分型面的平衡—balancing of parting surface10．锁紧角度—locking angle11．锁紧力—clamping force12．锁模板—safety strap13．精定位—Interlock, die lock14．困气—air trap15．排气槽—vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱—angled pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2．制动Detention①滑块固定器— slide retainer②弹簧制动器— spring-loaded detention (plunger)③挡钉、挡板— stop pin, stop plate, slide stop3．导轨—gib, guide strip4．锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block 5．耐磨片—wear plate, wear strip6．压板—retainer7．螺钉—screw8．定位销—dowelF．斜顶机构Lifter1．斜顶头—lifter head2．斜顶杆—lifter rod, lifter shaft3．开口销—split pin4．固定板（压板）— retainer plate5．耐磨片—wear plate6．铜导套— bronze bushing7．衬套— spacer8．导轨— L – gib9．滑动块— slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程— ejection stroke②模具开档—daylight③粘模—stick④产品脱模—part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly①顶板（推板）— ejector plate②顶板固定板— retaining plate③推板导柱— ejector guide pin④推板导套— ejector guide bush⑤撑头—support pillar, pillar support3．复位机构Return System①复位杆（回程杆）— return pin, push – back pin②挡钉—stop pin, stop button③压簧—compressed spring④碟簧—a stack of “Belleville” washers⑤早复位机构—early return system⑥强制复位机构—positive return system4．顶出方法 Ejection Techniques1）顶杆顶出—pin ejection2）顶管顶出— sleeve ejection3）顶块顶出— bar ejection4）扁顶顶出— blade ejection5）顶板顶出— stripper ejection6）油缸顶出— hydraulic ejection7）气顶— air ejection8）阀门顶出—valve ejection5．顶出元件Ejection Elements1）拉料杆—sprue puller, sucker pin2）顶杆—ejector pin3）阶梯式顶杆— stepped ejector pin4）顶管— ejection sleeve,sleeve5）扁顶— ejector blade, slabbed off ejector pin6）顶块—stripper bar7）顶环—stripper ring8）推板—stripper plate9）加速顶— accelerated ejection6．顶出辅助机构Supplementary operating system1）弹簧柱塞器—spring – loaded plunger2）弹珠定位器— ball catch system3）插销式锁扣— Latch – lock4）尼龙拉杆装置— friction puller device7．电器元件Electric Components1）压力传感器—pressure transducer2）限位开关—limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差—temperature variation2）水孔（水道）—waterlines, water-ways, flow-way, channel 3）水路—cooling circuit4）水路示意图—water schematic, schematic circuit5）冷却液—coolant, coolant fluid6）内连接—interconnect7）外连接—external connection8）出口、入口—outlet、inlet9）漏水—water leakage2．水路分布Circuits1）阶梯式水路—stepped system2）喷淋—baffled hole system3）斜孔式水路—angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male2）隔水片—baffle3）密封圈—O – ring4）快插水路接头—quick disconnect fitting, quick connection adaptor5）弯头—elbow6）偶合器（连接器、接头）—adaptor (including a plug & a socket)7）橡皮管—rubber hose8）分水板—water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹—thread2．管螺纹—pipe thread3．螺纹孔—screw hole, tapped hole4．起吊孔—handling hole, jack screw hole, eye bolt hole5．螺钉—screw6．内六角螺钉—socket headed cap screw （）7．沉头螺钉—flat headed cap screw （）8．螺栓—bolt, eye bolt9．螺母—nut10．锁紧螺母—locknut11．螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread （UNC）⑥美制细螺纹标准—United Fine thread （UNF）H．润滑Lubrication1．润滑槽—grease groove2．加油管—grease line3．油杯—lubrication fittingI．测量仪器Measuring Instrument s1．游标卡尺—vernier caliper2．千分尺—micrometer3．高度规—height gauge4．刻度规—dial gauge5．三坐标测量仪—Coordinate Measure Machine（CMM）6．塞规—pin gauge7．圆角量规—radii gauge8．轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2．试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, seca．注塑（充填）时间—filling time, injection timeb．冷却时间—cooling timec．补缩时间—packing timed．保压时间—holding timee．成型周期—cycle time②速率、速度Velocity, %、speed, in/seca．注塑（充填）速度—injection speedb．保压速率—hold pressure velocityc．螺杆转速—screw rotation speed③压力Pressure（Prs.）, psia．注塑压力—injection pressureb．保压压力—hold pressurec．回压（背压）—back pressure④温度T emperature（Temp.）, °Fa．注塑机喷嘴温度—nozzle temp.b．料筒前段、中段、后段温度—barrel front、middle、rear temp.c．模温—mould temp.d．料温—purged resin melt temp.e．空射料温—air shot melt temp.。
模具专业术语
模具专业术语————————————————————————————————作者：————————————————————————————————日期:ﻩ模具专业术语——注塑模(锦浩塑胶模具厂)EngｌisｈTraｉninｇ——Iｎjectｉon Mｏld（一）模具专业基本用词Ｐrofesｓional Ｔeｒms１.塑料—ｐlａstic, resin2．样件—ｓample3. 钢料—sｔeeｌ４. 注塑机—injecｔion mａchine, pｒesｓ５．产品—paｒt, prｏdｕct, mouldiｎg６．模具—mold, moｕlｄ, toolＡ简易模（样板模)—prototype mold Ｂ量产用模具—proｄuctio ｎmｏld7. 三维造型(数模）—modeｌ, 3D dａｔa8．二维产品图—2Ｄparｔdrawing９. 设计—ｄesｉｇn10．制造—ｍanufａcture, build ｕp, construction１1．检验—cheｃk, ｉnｓpeｃtｉｏn12.测量—measｕre，inspecｔion13.修改—chａnge, mｏｄify, ｃoｒrection14. 工程更改—ｅnｇineer cｈange１5．质量—qｕality１６. 数量—quantiｔy17. 基准—ｄａｔuｍ, ｒefeｒｅnｃe（二)如何解析2D 产品图？Ｈow tｏread 2D part drａwing？一. 产品几何Geoｍｅtry1．点—poinｔ2.线（边）—line, ｅdge3.面faｃeA 侧面—siｄｅB 表面—ｓurfaceC 外观面—aｐｐeａrａnｃｅsｕrfａｃe4．壁厚—ｗall thｉｃkneｓs, stoｃk thicknesｓ5．加强筋(骨位）—rib6.孔—hole7．细长的槽—sloｔ8．柱位—boss9.角—coｒnerA 圆角—ｆiｌｌｅｔB 倒角—chaｍferＣ尖角—sharp cｏrnｅr10.斜度—anglｅ，taper1１. 凹槽—rｅceｓs ,groove二. 分模信息Spliｔtiｎｇ1．分型线—parｔing line (Ｐ/L), splitｔiｎg lｉne２. 主分模方向—main directｉon, ｌiｎe of draｗ3．浇口设定—ｇatiｎg三. 产品标识Pａrt Iｄeｎtificａtion1. 产品名称—part nａｍe (Ｐ/N)２.产品编号+版本号—paｒt numbｅr ＋revisioｎ（Rｅv.）3. 型腔号—cａvitｙnuｍber4.材料标记—material symbol5. 模具编号—moｌd numbeｒ(no.）6．日期印—ｄatingｉnserｔ, date code7. 循环印—ｃycｌiｎg code8.公司标志—coｍpany loｇo四. 技术要求Sｐecificatioｎ(SpｅciaｌRｅquiｒement)1.项目启动表Kｉcｋ-ofｆshｅｅt１）项目名称—progrａｍname,projｅct naｍe2)产品名称—part namｅ, pｒoduct ｎame, part descriptｉｏn３) 产品编号—ｐart ｎuｍbeｒ(P/N)4) 客户模号—cｕstoｍer mold no.5) 项目启动日期— kick off dａtｅ，starｔdatｅ6)项目完成日期— duｅ dａte, lead tｉｍｅ7) 内模件用钢—ｔool sｔｅｅｌ8）型腔数量—numｂer of cavit iｅs９)数模文件编号—data.10）注塑材料—rｅsin，plastic, raw maｔｅrial1１）收缩率—ｓhrink, ｓhrinkage,sｈrink ｆactoｒ12)注塑机吨位—ｍoldｉng mａchine sｉzｅ， injeｃｔｉon machiｎe size １３）成型周期—cyｃle time14)型腔光洁度—caｖiｔy pｏlish1５) 型芯光洁度—core polｉｓh16）皮纹(晒纹)—tｅxｔurｅ, gｒain17）拔模斜度—dｒaft anｇle, ｒemoval ｔaper18）注塑件颜色及光泽—molｄeｄｃｏｌoｒ& ｇloss19) 模具加工地—manｕfａｃturing ｆaｃility２０）热流道供应商—maniｆｏｌd mａnuｆactureｒ, ｍａｎifolｄ supplieｒ2１)浇口位置—gaｔe ｌoｃation ／pｏｓitｉon22) 浇口类型—gａtｅtype23) 产品标识—stamp infｏrmaｔion, parｔidentificａtion２４）特殊要求—sｐeciaｌ instructiｏｎs2. 产品质量及外观要求Pａrt Quality & Apｐｅaraｎcｅ１）尺寸及公差Dｉmensioｎ&Toｌｅｒancｅ①重要尺寸—ｃritical dimensｉoｎ,importanｔdiｍ.，kｅy dim.②理论尺寸—ｎｏｍiｎalｄimension③实际尺寸—actuａｌdiｍension④公差—tolｅraｎce⑤公差带—tｏlｅrancｅrａnge⑥尺寸超差—dimensionｄeviａtion⑦接受（合格）—ａccepｔ, OＫ⑧拒绝(不合格）—rejecｔ, refｕse,oｂsolete,NＧ⑨让步接受—conceｓsion, ｓｐecial adｍiｔ⑩返工—re-wｏrk２）产品缺陷（较常见）Ｄefeｃts (normaｌ）①缩印—sｉnk mark, sｈrｉｎｋage②飞边—flａsh, burr③段差—mｉsmａtcｈｄｉｓcｒepancy④银丝纹—ｓｎake ｍaｒks, streak⑤弯曲—warpａｇe, ｄistoｒtion⑥打不足（缺料）—shorｔｓhot⑦熔接线—wｅld lｉne3．产品外观ParｔAｐｐearanｃｅ①产品颜色—paｒｔｃｏｌor②产品光泽—ｇloss③皮纹粒度—gｒain4．常用词汇、词组及短语NormａｌＷｏrd, Shｏｒt Seｎｔｅｎｃe1）单边—per side2)双边—both sides３) 加入,添加—aｄｄ,iｎcorporａtｅ４) 去除，取消—rｅmovｅ,ｃancel５) 满足…的要求,符合,与…要求一致—accｏｒｄing ｔｏ, conｆorｍto, satisfy, mｅeｔ6) 要求，需要—ｒequｉrｅ,neｅｄ,demanｄ7）确认—be ａｐproｖｅｄ, agreedｂy …8) 允许—peｒmｉｔ，ａlloｗ9) 在…范围之内—ｗithin1０）不可以,不允许，禁止—free from，preｖent, avｏid11）…,除非有另指—…unleｓsｏtherwｉｓｅspecified1２）…或少于—…or ｌess13) 自动化运作—automatiｃoperａｔｉoｎ１4）未注尺寸(详细形状）见三维造型Noｎｄimensioned ｃontｏur (dｅｔａiled ｓhape) ｓｅe ３D mｏｄel.15)分型线上的飞边(披缝)或段差应小于…Bｕrrs and diｓｃrｅpａｎcy onｔheＰ／Ｌshaｌl be… ｏr less.五．标题栏Titｌe Bloｃｋ１. 产品名称—part name２．图纸编号+ 版本号(索引号）—draｗｉng no．+ level （ｉndex)3. 一般公差[的标准] —generａl tolerａnｃe（三) 如何阅读制模标准？Hｏw to read toｏling stanｄaｒd?一．模具结构术语Moｌd CｏnsｔrｕctiｏｎTermiｎologyA．模架Mold Ｂａｓe1.模架量化特征Mｅasuremｅnt Feature①长X 宽Ｘ高—ＬeｎgtｈXＷidth X Height②模具推高尺寸（模厚）—sｔａck hｅiｇht ｏf ｍould③模具重量—totａl weight ofｍould,mouｌd thｉｃkｎesｓ2. 定模底板—fｒont pｌaｔe, ｔｏｐclamｐiｎｇplａte, cｌamｐpｌatｅ，clａmｐinｇplate３．定模板—cａvｉty plａｔe，fixｅd moｕlｄplａte, A – platｅ4. 动模板—cｏｒe plａｔe,ｍoｖing mｏｕｌd ｐlate, B – plate５. 支撑板—ｓuppｏｒt plａte, baｃking ｐlate6. 模脚—support bloｃks，raｉlｓ，riseｒs, spａｃeｒblｏｃk７. 顶杆固定板—reｔaining ｐｌatｅ, ejector retainｉｎg plate８. 顶板—ejｅctor ｐlaｔe9．动模底板—baｃｋpｌａte1０．导柱—ｇｕｉde ｐillar, leａｄer pin, ｇuｉdeｐin11．导套—gｕidｅｂuｓh, ｌeadｅr ｐｉnｂush12.复位杆—rｅturn piｎ，push-back ｐｉｎ13．弹簧—ｓpriｎｇ14. 撑头—supｐｏrt pillar１5．推板导柱、导套—ejectiｏn gｕidｅpｉn / ｂush16．挡钉—ｓtop ｐiｎ,stoｐ buttoｎ１７．站立脚—sｔａndiｎg-ofｆpiｌlars18．标牌—pｌaquｅscutcheonB.成型零部件moｕｌding components1９. 型芯—cｏre20．型腔—cavitｙ２1. 镶针—core ｐin２２. 镶块—insｅrt，sｐlit23.滑块—sｌide, sliｄiｎｇsｐlit２4. 斜顶—lifteｒ,angled-liｆt ｓｐlitA 斜顶头—lｉftｅr hｅadB 斜顶杆—ｌifter rod, lｉｆteｒｓｈａft2５. 成型顶杆—ｍoulding facｅpin, form pｉｎC．浇注系统Fｅed System1．塑料Mouldingａ．主流道—ｓｐrueｂ. 分流道runｎer①主分流道— mａin ruｎner ②二级分流道— braｎcｈ rｕnｎeｒ分流道断面形状cｒosｓ-sｅｃtional ｓｈape oｆｒunner①圆形—ｆuｌl roｕｎd②半圆形—semiciｒcｕｌar③梯形—trapｅｚoidaｌｃ．浇口gaｔｅ常用浇口形式nｏrmａl ｇate tyｐe :①边缘浇口（J型浇口) —eｄgｅｇate, J –ｇate②侧浇口—side gate③潜伏式浇口—sub-gaｔe, ｃａshew gatｅ， subsurfａｃｅ gaｔe, suｂmaｒine gaｔe④潜伏式二次浇口(隧道式浇口) —ｔunnｅl gａｔe ontｏfeｅｄer post⑤点浇口—pｉn gａｔe⑥直接浇口(主流道型浇口) —ｓprue gate, direct gａte⑦护耳式浇口—tａb gａted. 模腔—imprｅｓsｉｏnｅ. 冷料井—colｄsｌug welｌf．热流道—hot runner２.模具零件moｌｄcoｍponentsa. 定位圈—lｏｃating ring, lｏｃation ｒing, regｉsｔｅr riｎｇb. 浇口套—spｒue bushc．挡圈—sｔｏp ｒingd．浇口镶块—gate inｓeｒte．热流道板—mａｎifoldｆ. 热嘴—ｈｏｔｄropＤ.分型面及其锁紧、排气Paｒtｉｎg Sｕrfaｃｅ, inter-loｃking＆ventｉng 1．分型线—paｒtｉnｇline ( P/Ｌ）２. 镶拼线—bｏdｙlｉnｅ，ｊoiｎt lｉne3．平/不平的分型面—ｆlａt ／non – flaｔ pａrting sｕrface4．封胶面—sｈut ofｆsurfaces, ｓeａｌ－ｏff suｒfａceｓ5．擦位—shuｔoff6. 碰穿位—kiｓs-ｏff7. 管位—pａrtｉｎgｌinｅｌock８.分型面的释放(避空) —rｅｌieｆｏｆpａｒtiｎg ｓuｒｆａｃe９．分型面的平衡—bａlanｃiｎｇof ｐarｔing ｓurface10．锁紧角度—ｌockｉng anglｅ1１.锁紧力—cｌａｍpingｆoｒce1２．锁模板—safetｙstｒap1３．精定位—Inｔeｒloｃk,die locｋ14．困气—aｉｒtrap1５．排气槽—vent, veｎt ｓlｏtＥ.滑块机构Slide１．驱动Acｔuaｔｉｏｎ①斜导柱—anglｅｄｐin, ｈorn pｉn, cａm pin②弹簧—sprinｇ③油缸—ｈydraulｉc cyliｎder２．制动Dｅｔeｎtion①滑块固定器—sｌide rｅtａｉｎer②弹簧制动器—spｒing-loaded detentｉon (plunger)③挡钉、挡板—ｓtop pin, stop platｅ, slide stop3．导轨—gｉｂ,gｕide sｔrip4．锁紧块(楔紧块)—heel blｏcｋ,ｌｏcking ｈｅel，wｅｄge blｏｃk, cｈasｅbl ｏｃk5. 耐磨片—wear pｌａte，ｗｅar strip6. 压板—reｔaiｎeｒ7. 螺钉—screw８．定位销—dowelＦ.斜顶机构Ｌiftｅｒ1.斜顶头—lｉfｔｅｒｈeａｄ2．斜顶杆—liｆtｅr roｄ，lifｔer ｓhａfｔ3．开口销—spｌit ｐin4．固定板(压板) —reｔaiｎer plａｔｅ5. 耐磨片—wear ｐlatｅ６. 铜导套—ｂrｏnzｅbuｓhing7．衬套—spaｃeｒ８. 导轨—L – gib9. 滑动块—slideG．顶出系统EjectioｎSyｓtem１. 基本词汇Baｓｉc Worｄ①顶出行程—ejectｉｏn stroke②模具开档—ｄayligｈt③粘模—stｉck④产品脱模—part iｓpuｓh ofｆfrom,ｃlearｐart of mouｌd, seｐaratioｎofｐart2. 顶板机构Ejector pｌａｔe asｓembly①顶板(推板) —ｅｊｅｃｔoｒplａtｅ②顶板固定板—retａiniｎg plａte③推板导柱—ejector gｕiｄｅpin④推板导套—ｅjｅctor guide ｂusｈ⑤撑头—supｐort pｉllar, pilｌarｓupport3．复位机构Return Sｙsteｍ①复位杆(回程杆)—return ｐin，ｐush – back pin②挡钉—sｔｏｐpin, sｔop buｔton③压簧—coｍpｒｅsｓeｄsｐring④碟簧—a sｔack of “Ｂeｌleviｌｌｅ”wasｈers⑤早复位机构—ｅａrly return sｙsｔem⑥强制复位机构—posｉtｉve retｕrｎsｙsteｍ4．顶出方法Ejection Techniqｕes１) 顶杆顶出—ｐiｎeｊection２) 顶管顶出—ｓleｅve ejｅction3）顶块顶出—bａr ejｅction４) 扁顶顶出—bｌａde ｅｊｅction５) 顶板顶出—ｓtripper eｊecｔｉon６) 油缸顶出—hydraｕlic ejｅctｉｏn7) 气顶—air ｅjectioｎ8）阀门顶出—valve ejｅｃtion5. 顶出元件Ejecｔｉon Eｌｅments1) 拉料杆—spｒue pｕｌlｅr，sｕckerｐin2) 顶杆—ejector pｉｎ3) 阶梯式顶杆—ｓｔeppｅd eｊｅctor ｐin4) 顶管—eｊeｃtion sleｅｖe，slｅevｅ５）扁顶—ｅjｅcｔor blaｄe, slａbｂeｄoff ejecｔｏr pin6）顶块—striｐper bar7）顶环—strippｅr ｒing８)推板—ｓtripper plate9)加速顶—accｅleｒaｔｅd ejeｃtioｎ6. 顶出辅助机构Supｐlｅmｅntaryｏpｅraｔｉng sysｔem1）弹簧柱塞器—sprｉnｇ–ｌoａdｅｄｐｌunger２）弹珠定位器—baｌl catch ｓyｓtem3) 插销式锁扣—Lａtch– lock4) 尼龙拉杆装置—fｒiｃtion pullｅr ｄeｖice７．电器元件Electrｉc Coｍpｏnents1) 压力传感器—pｒessuｒe trａｎｓduｃer2) 限位开关—ｌimit swｉtchF．冷却系统Ｃooling Ｓysｔem1. 基本词汇BａsiｃWｏrd１)温差—teｍｐerａture variａtion2) 水孔（水道）—ｗaｔｅrｌines, wａtｅr-waｙｓ, flｏw-wａy, cｈannel3) 水路—ｃｏolｉng ciｒcuit4) 水路示意图—wateｒsｃhｅmａtｉc，ｓchematic circuit5) 冷却液—cｏｏlaｎt，coｏlant fluid６）内连接—iｎｔercｏnnｅct7) 外连接—eｘteｒnaｌｃｏｎnectioｎ8）出口、入口—oｕtlｅt、iｎleｔ9) 漏水—ｗａter ｌeakage2. 水路分布Circｕits1)阶梯式水路—steppeｄsyｓteｍ２)喷淋—bａffled holeｓｙstem3) 斜孔式水路—angled hole sｙｓtem3. 水路元件Ｃoｍｐonents1）闷头（螺塞、止水栓) — (threａdlesｓ)brasｓpressure pｌuｇ:feｍale plug & male2）隔水片—bafflｅ3) 密封圈—O – rinｇ4）快插水路接头—ｑuick disconｎｅcｔｆｉｔtinｇ, qｕick coｎneｃｔi ｏｎadaptor5) 弯头—elｂｏｗ６)偶合器（连接器、接头) —adapｔor （iｎcｌｕding a plug & a sｏcket）7）橡皮管—rubbｅｒｈoｓｅ８)分水板—water mａnｉｆolｄG.螺纹、螺纹孔& 螺钉Tｈread,tｈｒead ｈole & ｓcrｅｗ1．螺纹—threａd２. 管螺纹—pipe thｒeaｄ3．螺纹孔—screｗｈｏｌe, tappｅd hｏle4. 起吊孔—ｈandｌｉｎg holｅ, jack scｒｅw hole, eyｅbolt hole５.螺钉—screw6．内六角螺钉—sockeｔheａded cap sｃrｅｗ（s．h.c.s.）7．沉头螺钉—ｆlat headed ｃaｐscrew （f．ｈ.c.s）８. 螺栓—bｏlｔ, eyｅbｏｌｔ9．螺母—ｎuｔ10.锁紧螺母—lｏcknut１1．螺纹标准Tｈｒead Stａｎdａrd①公制标准—Metric②英制标准—Imｐｅｒｉal③英制管螺纹标准—Bｒiｔｉsh Ｓtａndard Ｐｉpe thread （BSP)④美制管螺纹标准—ＮPＴ⑤美制粗螺纹标准—UｎitｅｄCoarse tｈｒeａｄ（UNＣ）⑥美制细螺纹标准—Ｕnｉted Fｉnｅtｈrｅａd（ＵNＦ）H．润滑Ｌubricatiｏn１．润滑槽—greａｓe grooｖe２．加油管—grｅａsｅlｉｎe3．油杯—luｂriｃａtioｎfittｉngI．测量仪器Ｍｅasuring Iｎsｔrｕmｅntｓ1. 游标卡尺—vernierｃaliper2. 千分尺—ｍicrｏmeter3.高度规—ｈeｉght gauｇｅ４. 刻度规—ｄiａｌｇａuge5．三坐标测量仪—Coordinaｔe Ｍeasuｒe Maｃhiｎｅ（CＭM）6．塞规—piｎgauge７．圆角量规—radii gauｇe8．輪廓投影機—proJ.注塑机参数Ｉｎjectｉon MacｈｉｎｅPａrameter1. 注塑机规格参数Ｉｎjecｔiｏn MachineＳpeｃifｉｃation①锁紧类型ｃlamp typea.油缸—hydｒauｌic ｂ．肘杆式—togｇle②垂直注塑机导柱间距—tie baｒverticalｃlｅarance③水平注塑机导柱间距—tie bar hoｒizonｔａlｃｌearancｅ④台板尺寸—platenｄim.⑤最小/最大模厚—molｄheighｔMiｎ. / Mａx., Min./ Max. moldｔhickｎess⑥最小／最大注塑机开档—ｏpen daｙliｇht Min. ／Max.⑦锁紧行程—ｃlamｐsｔroke⑧锁紧力—clampｉng forｃe⑨顶出行程—ejector stroke⑩顶出力—ejector forｃe２. 试模工艺参数Mouｌdiｎg ProcessＰaｒameter，macｈine setting①时间Ｔimer(TM)，seca. 注塑(充填）时间—fｉｌling time, iｎjｅctｉon timeb．冷却时间—cｏolｉnｇtimec. 补缩时间—ｐacｋinｇtimｅｄ.保压时间—holding ｔiｍee. 成型周期—cyｃｌe time②速率、速度Ｖelocｉｔy, ％、spｅed，in/seca．注塑（充填)速度—iｎjectiｏn sｐｅedb．保压速率—ｈｏld pressure velocitｙc．螺杆转速—screw rotatioｎｓｐeed③压力Pressｕｒe(Ｐrs．), psiａ. 注塑压力—ｉｎｊeｃtioｎpressurｅb. 保压压力—ｈoｌd prｅssuｒec．回压(背压）—bａｃk prｅｓsure④温度Temｐeratｕre(Teｍp．）, °Fa．注塑机喷嘴温度—nｏzzlｅｔｅmp.b．料筒前段、中段、后段温度—barrel ｆrｏnt、middle、rear temp.c．模温—mouldｔemp.d．料温—purgｅd resin melt ｔemp．ｅ．空射料温—air sｈot melt tｅmｐ.。
模具设计专业术语
模具设计专业术语中英对照一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper elei模具专业英语词汇dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢俗称大全广东模具术语深圳方言模具术语: 模胚类: 唧嘴---浇口衬套法兰---定模浇口衬套定位环,扶针---回针, 垃圾钉---顶针板止停销杯头螺丝---内六角沉孔螺丝模具类: 前模---又叫A模或定模, 后模---又叫B模或动模行位---滑块, 钶---镶在后模上的芯子(或叫模仁),机械类工具类: 锣床---铣床, 锣床批土---铣床虎口钳,磨床批土---磨床打直角虎门钳, 匙把揦---活钳或开口扳手的一种称呼刀具工具类: 牙嗒---丝攻, 坑手-攻牙用的扳手,机转---铁圆规, 奔子---磨成尖头用于敲击划线相交定位点的工具产品类: 止口---夹口美术线,又称遮丑线, 啤把---拨模斜度,火箭脚---位于司柱的加强筋机米螺丝：无头螺丝中山方言模具术语模具类: 斜导柱=斜边锁紧块=铲鸡东莞模具术语：机械工具类：虎钳------批士；C形夹-----虾公码；钻孔------钻窿；加工中心-电脑锣；偷胶-------减胶火山口-------司筒底部的减胶位；公模肉＝后模；母模肉＝前模環保標志=回收章細水口=針點澆口潛水=針點澆口；鑲件=入子；排氣槽=逃氣道披鋒=毛邊；加膠=加料；密封圈=膠圈中托司=頂出導柱(套)=哥林柱水口扣針＝拉料頂針插穿(碰穿)＝靠破曬紋＝咬花波子螺絲＝定位珠开模器=拉胶模胚类：水口边细水口或简化型模胚的从水口板上贯下来的那支导柱中托司顶针板导柱;零度块方型辅助器模具类斜顶------斜方水塔，水桶------模仁上钻个深孔，中间用铜片或亚加力板隔开，运水一边进一边出来冷却的水喉，水嘴-----冷却水接口;呵----模仁铜公-----放电用的电极; 弹弓---弹簧;入水---进胶点模具加工类的飞模------合模好象用白话说的外（音是如此，估计是WIRE）---线切割放电-----打火花;省模，打光----抛光光刀---我们这是用来指CNC精加工加工模仁，多用于公模开粗---粗加工，留少许余量开框---模胚上加工放模仁的位置穿线孔---线割时用来穿钼丝的产品类加强筋---加强用的骨位; 美工线---上下盖装配的中间的间隙（可有效防上错位）行位>滑块;司筒>套筒入子>镶件（INSERT）入子为台灣叫法;斜顶>斜顶块或斜顶杆KO孔> 顶棍孔;司筒针> 套筒针撑头> 支撑柱(防止B 板变形的) ;铲鸡>行位锁紧块治具> 工具(夹具) ；喉咀> 水管头；行位波仔>滑块斜器；中托司>浇口衬套水口板>流道板；细水口板>分流道板勾针>拉料杆；B板>动模板；A板>定模板产品的夹线>分型线；运水>冷却水道；回针>复位顶针；隔热板>热流道模上用的撬模位>用来公开AB板的；码模坑>注射时固定上下模的通框>把框开成通；大水口模----二板模；小水口模----三板模斜顶(又叫推方)----楣仔方；方铁----凳仔方夹水纹----熔胶线火花纹----电火花加工后留下的纹粗公----电火花粗加工用的铜公精公----电火花精加工用的铜公晒字----做好菲林再拿去加字体的加工方法开模器=拉胶=拉模扣密封圈=膠圈=防水胶圈=O型圈波子螺絲＝定位珠=弹弓波子扣机就是控制多板分型的机械装置模具类：K.O孔——顶棍孔——用来顶顶针板的。
模具设计专业术语
中英对照一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper elei模具专业英语词汇dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢俗称大全广东模具术语深圳方言模具术语: 模胚类: 唧嘴---浇口衬套法兰---定模浇口衬套定位环,扶针---回针, 垃圾钉---顶针板止停销杯头螺丝---内六角沉孔螺丝模具类: 前模---又叫A模或定模, 后模---又叫B模或动模行位---滑块, 钶---镶在后模上的芯子(或叫模仁),机械类工具类: 锣床---铣床, 锣床批土---铣床虎口钳,磨床批土---磨床打直角虎门钳, 匙把揦---活钳或开口扳手的一种称呼刀具工具类: 牙嗒---丝攻, 坑手-攻牙用的扳手, 机转---铁圆规, 奔子---磨成尖头用于敲击划线相交定位点的工具产品类: 止口---夹口美术线,又称遮丑线, 啤把---拨模斜度, 火箭脚---位于司柱的加强筋机米螺丝：无头螺丝中山方言模具术语模具类: 斜导柱=斜边锁紧块=铲鸡东莞模具术语：机械工具类：虎钳------批士； C形夹-----虾公码；钻孔------钻窿；加工中心-电脑锣；偷胶-------减胶火山口-------司筒底部的减胶位；公模肉＝后模；母模肉＝前模環保標志=回收章細水口=針點澆口潛水=針點澆口；鑲件=入子；排氣槽=逃氣道披鋒=毛邊；加膠=加料；密封圈=膠圈中托司=頂出導柱(套)=哥林柱水口扣針＝拉料頂針插穿(碰穿)＝靠破曬紋＝咬花波子螺絲＝定位珠开模器=拉胶模胚类：水口边细水口或简化型模胚的从水口板上贯下来的那支导柱中托司顶针板导柱 ;零度块方型辅助器模具类斜顶------斜方水塔，水桶------模仁上钻个深孔，中间用铜片或亚加力板隔开，运水一边进一边出来冷却的水喉，水嘴-----冷却水接口 ;呵----模仁铜公-----放电用的电极 ; 弹弓---弹簧 ; 入水---进胶点模具加工类的飞模------合模好象用白话说的外（音是如此，估计是WIRE）---线切割放电-----打火花 ;省模，打光----抛光光刀---我们这是用来指CNC精加工加工模仁，多用于公模开粗---粗加工，留少许余量开框---模胚上加工放模仁的位置穿线孔---线割时用来穿钼丝的产品类加强筋---加强用的骨位 ; 美工线---上下盖装配的中间的间隙（可有效防上错位）行位 >滑块 ;司筒 >套筒入子 >镶件（INSERT）入子为台灣叫法 ;斜顶 >斜顶块或斜顶杆 KO孔 > 顶棍孔 ;司筒针 > 套筒针撑头 > 支撑柱(防止B板变形的) ;铲鸡 >行位锁紧块治具 > 工具(夹具) ；喉咀 > 水管头；行位波仔 >滑块斜器；中托司 >浇口衬套水口板 >流道板；细水口板 >分流道板勾针 >拉料杆；B板 >动模板；A板 >定模板产品的夹线 >分型线；运水 >冷却水道；回针 >复位顶针；隔热板 >热流道模上用的撬模位 >用来公开AB板的；码模坑 >注射时固定上下模的通框 >把框开成通；大水口模----二板模；小水口模----三板模斜顶(又叫推方)----楣仔方；方铁----凳仔方夹水纹----熔胶线火花纹----电火花加工后留下的纹粗公----电火花粗加工用的铜公精公----电火花精加工用的铜公晒字----做好菲林再拿去加字体的加工方法开模器=拉胶=拉模扣密封圈=膠圈 =防水胶圈=O型圈波子螺絲＝定位珠 =弹弓波子扣机就是控制多板分型的机械装置模具类： K.O孔——顶棍孔——用来顶顶针板的。
模具专业英文术语大全
模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车（AGV）57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控（CNC）机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
精选文库模具专业术语大全punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销模具零件英语词汇air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger加强筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块模具模板英语词汇feature die 公母模femaledie 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚模具五金零件英语词汇eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guidepad 导料块outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板ribbon punch 压筋冲子bottom plate 下托板(底板)stripping plate 内外打( 脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板cover plate 盖板wire spring 圆线弹簧outerguiding post 外导柱stopscrew 止付螺丝located pin 定位销outer bush 外导套模具冲压英语词汇extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙punch wt. 上模重量模具工程类英语词汇精选文库plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸, 冲凸) draw hole 抽孔air vent vale 通气阀anchor pin 锚梢angularpin 角梢baffle调节阻板angularpin 倾斜梢baffleplate 折流档板ballbutton 球塞套ballplunger 定位球塞ball slider 球塞滑块binderplate 压板blankholder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumperblock 缓冲块buster堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平模具厂常用标准零配件英语词汇die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowelhole 导套孔dowelpin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模groove 压线blanking 下料stamp letter 冲字( 料号)shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢精选文库locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stoppin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/ 锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板××××××××××××××××××××××××××××××××××××××××××××××××××××××××××。