SPH-2500 设备说明书---英文版
TETRIS 2500 High Impedance Active Probe Instructio
TETRIS® 2500High Impedance Active Probe Instruction ManualCopyright © 2018 PMK GmbH All rights reserved.Information in this publication supersedes that in all previously published material.Specifications are subject to change without notice.ManufacturerPMK Mess- und Kommunikationstechnik GmbHKönigsteiner Str. 9865812 Bad Soden, Germany Internet: www.pmk.deTel: +49 (0) 6196 5927 - 930 E-mail: ************Fax: +49 (0) 6196 5927 - 939WarrantyPMK GmbH warrants this oscilloscope accessory for normal use and operation within specifications for a period of two (2) years from date of shipment and will repair or replace any defective product which was not damaged by negligence, misuse, improper installation, accident or unauthorized repair or modification by the buyer. This warranty is applicable only to defects due to material or workmanship. PMK GmbH disclaim any other implied warranties of merchantability or fitness for a particular purpose. PMK GmbH will not be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if PMK GmbH has been advised of the possibility of such damages arising from any defect or error in this manual or product.23Declaration of ConformityTETRIS ® 2500(EC conformity marking)The manufacturer declares,that this product is designed and manufactured in accordance with the requirements of the specified Directives and Standards as listed below. The product carries the CE mark.EU Directives covered by this declaration:2004/108/EC Electromagnetic Compatibility Directive 2006/95/EC Low V oltage Equipment Directive2002/96/EC Waste Electrical and Electronic Equipment2002/95/EC Restriction of use of certain Hazardous Substances and its revised version 2011/65/EU The basis on which conformity is being declared:EN61010-1:2010 Safety requirements for electrical equipment for measurement, control and laboratory use, general equipment requirementsEN61010-031:2002 + A1:2008Safety requirements for hand-held probe assemblies for electrical measurement and test EN61326-1:2006 Electrical equipment for measurement, control and laboratory use –EMC requirements. Basic Immunity - static discharge per EN61000-4-2RoHS and WEEE Statements and Confirmations issued by our vendors that no hazardous or restricted sub-stances are used to manufacture components, parts and subassemblies for our products.TETRIS Power SuppliesModels PS-01 and PS-01-INT (International version with exchangeable mains adapters) are manufactured in Germany by Friwo Gerätebau GmbH. The power supplies are not included in the scope of this declaration of conformity. Upon request we are able to provide full information about conformity and certifications of the power supplies made by Friwo and supplied with our TETRIS probes.WEEE/ RoHS Directives(EC conformity marking)Your help and efforts are required to protect and keep clean our environment. Therefore return this electronic product at the end of its life either to the Service Department of PMK Mess- undKommunikationstechnik GmbH or take care of separate WEEE collection and professional WEEE treatment yourself. Do not dispose as unsorted municipal waste.* EC Directives:WEEE Directive 2002/96/EC - Waste Electrical and Electronic EquipmentRoHS Directive 2002/95/EC - Restriction of the use of certain Hazardous Substancesin Electrical and Electronic EquipmentSafety Symbols TETRIS® 2500 The following symbols may appear on the product or in this instruction manual:Caution, risk of danger. Refer to manual.Caution, risk of electric shock.Earth (ground) TERMINAL.4Safety Information TETRIS® 2500To avoid personal injury and to prevent fire or damage to this product or products connected to it, review and comply with the following safety precautions. Be aware that if you use this probe assembly in a manner not specified the protection this product provides may be impaired.Only qualified personnel should use this probe assembly.Use only grounded instruments.Do not connect the probe ground lead to a potential other than earth ground. Always make sure the probe and the measurement instrument are grounded properly.Connect and disconnect properly.Connect the probe output to the measurement instrument and connect the ground lead to earth ground before connecting the probe to the circuit under test. Disconnect the probe input and the probe ground lead from the circuit under test before disconnecting the probe from the measurement instrument.Observe probe ratings.Do not apply any electrical potential to the probe input which exceeds the maximum ratings of the probe.Keep away from live circuits.Avoid open circuitry. Do not touch connections or components when power is present.Do not operate with suspected failures.Refer to qualified service personnel.Indoor use only.Do not operate in wet/damp environment. Keep product surfaces dry and clean.Do not operate the product in an explosive atmosphere.5About the Tetris Active Probe System TETRIS® 2500 PMK presents a unique Inline Probing System – the TETRIS® active probe which can contact adjacent square pins in 2.54 mm pitch simultaneously. The probe‘s housing is T-shaped so that many probes can be positioned next to each other in a never ending chain.Like this a number of measurements can be performed at the same time. The TETRIS® is system-independant and its standard SMA connector can be plugged onto any measuring instrument with a 50 Ω input.With an input resistance of 1 MΩ and an input capacitance of 0.9 pF the TETRIS® probe is suitable for measure-ments in all frequency ranges.Compared to passive probes the TETRIS® active probe offers a high input impedance into the GHz-range.Passive probes with their relative high input capacitance load the signal source already at frequencies above 100 kHz.That´s why the TETRIS® active probe with its high input resistance and its low input capacitance is the ideal probe for most of your daily measurments.TETRIS® 2500 testing adjacent pinsin 2.54 mm Pitch6Operating Basics TETRIS® 2500 When using this active probe device make sure the measuring instrument is set to 50 Ω input coupling and the probe is connected to the power supply.HandlingNote that the probe cable is a sensitive part of the probe. Do not damage through excessive bendingor pulling. Avoid mechanical shock to this product in general to guarantee accurate performance andprotection.Power SupplyDouble V oltage Single V oltageInner Connector +12 V 24 VInner Shielding -12 V 0 VOuter Shielding Earth-Ground Open (floating)Required Current 150mAConnector Type Triaxial Lemosa ConnectorPlease note, that any noise of the supply voltage influences the noise of the signal in general. Maintenance CleaningTo clean the exterior of the probe use a soft cloth moistened with either distillated water or isopropyl alcohol. Before use allow the probe to dry completely.78Specifications that are not defined to be guaranteed are typical and published as general information to the user. The instrument should have warmed-up for at least 20 minutes and the environmental conditions should not exceed the probe's specified limits.Electrical SpecificationsAttenuation Ratio10:1 ± 0.5 % at DC Dynamic Measuring Range ± 8 V System Bandwidth (1) 2 GHz (-3 dB)Bandwidth (Probe only)2.5 GHz Maximum Rated Input V oltage20 VMax. Input Voltage and Dynamic Measuring RangeThe TETRIS ® active probe is protected against electro-static-discharge voltage (ESD). However, applying input-voltages outside the specified limits can result in destruction of the probe´s amplifier.The maximum amplitude of the applied signal may not exceed the limits of the graph below, to avoid input linearity errors and damage to the probeThe maximum amplitude of the applied signal may not exceed the limits of the graph below, to avoid damage to the probe.To avoid input linearity errors and damage to the probe feel free to contact our customer support under ****************************************************************************.(1) connected to oscilloscope >2.0 GHzV o l t a g e [V ] A C p e a kFrequency [Hz]Input Voltage vs. Frequency TETRIS ® 25001101001G10G100M 10M1MDynamic Measuring Range Maximum Input VoltageElectrical CharacteristicsInput Resistance (System) > 1 MΩInput Capacitance (System) 0.9 pFOscilloscope Input Coupling 50 Ω AC / DCInput ImpedanceNote that the input impedance of the probe decreases as the frequency of the applied signal****************************************************************************.Mechanical CharacteristicsWeight (probe only) 96 gCable Length 1.3 mEnvironmental specificationsAltitude operating up to 2000 mnon-operating up to 15000 mTemperature Range operating 0° C to +45° Cnon-operating -40° C to +71° CMaximum Relative Humidity operating 80 % relative humidity for temperatures up to +31° C,decreasing linearly to 40 % at +45° C9Accessories TETRIS® 250010Accessories TETRIS® 250011Scope of Delivery TETRIS® 2500 The following items are included in the scope of delivery. Please check the delivery for completeness. If any item is missing, send a message to our service department and we will send you this item immediately.Item QtyGround Blade 1Ground Lead 6 cm 1Ground Lead 12 cm 1Ground Lead 90° 5 cm 1Ground Lead 90° 10 cm 1Ground Leaf 1Instruction Manual 1L-In Adapter 1Marker Bands 4 colors 1PCB Adapter 1Picohook TM black 1Picohook TM red 1Power Supply 1Probe 1self adhesive Cu Pad (2 x 2 cm) 2Solid Tip 1Spring Tip 1Y-Lead Adapter to 0.8 mm sockets 1Z-Ground 1Use ground lead only for connections to earth ground.The accessories provided with the probe have been safety tested. Do not useany other accessories than those “originally” provided.M-TETRIS2500 Revision I - Jan 2018。
Sun Blade 2500 入門指南说明书
Sun Microsystems, Inc.請將關於此文件的意見傳送到：/hwdocs/feedback Sun Blade™ 2500入門指南文件編號 817-0626-11 2004 年 4 月，修訂版 A請回收Copyright 2004 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. 版權所有。
Sun Microsystems, Inc. 對於本文件所述產品所使用的技術擁有智慧財產權。
具體而言，這些智慧財產權可能包括但不限於/patents 上所列的一項或多項美國專利權，以及在美國及其他國家擁有的一項或多項其他專利權或申請中專利權。
本文件及相關產品在限制其使用、複製、發行及反編譯的授權下發行。
未經 Sun 及其授權人 (如果適用) 事先的書面許可，不得使用任何方法以任何形式來複製本產品或文件的任何部份。
協力廠商軟體，包含字型技術，其著作權歸 Sun 供應商所有，經授權後使用。
本產品中的某些部份可能衍生自加州大學授權的 Berkeley BSD 系統的開發成果。
UNIX 為美國及其他國家的註冊商標，已獲得 X/Open Company, Ltd. 專屬授權。
Mozilla 是 Netscape Communications Corporation 在美國及其他國家的商標或註冊商標。
Sun 、Sun Microsystems 、Sun 標誌、Sun Blade 、AnswerBook2、 、NetBeans 、Power Management 、Java 、StarOffice 、Java 3D 、Solstice Disksuite 、SunPCI 、SunForum 、SunSolve 、ShowMe 、Java Coffee Cup 標誌、OpenBoot 及 Solaris 是 Sun Microsystems, Inc. 在美國及其他國家的商標或註冊商標。
2500中文说明
ASTRO卫星XTS 2500Ⅲ型91ARS的用户登录和文本消息功能注：我在大写模式），多挖掘键将只有滚动大写字母。
（例如：一个，“乙->的C -”2）ii）在数字锁定模式下，按下键盘会只输入数字位数。
随后按相同的键位会插入相同的文本消息（没有多抽头）。
表三：键盘字符关键是数按时间（正常模式）关键1 2 3 4 5 6 7 8 90 0或按住以切换普通文本进入模式，大写模式和Num Lock模式。
1 1。
，？！; @ _ - *＃＆$ / + = \“'（）美国广播公司美国广播公司2 23高清3登士4 ghi 4 GHI5 jkl 5 JKL6 6 MNO的二氧化锰7 PQRS的7 PQRS的德国TUV德国TUV 8 89 wxyz 9 WXYZ*空间＃删除一个字符ASTRO卫星XTS 2500Ⅲ型92ARS的用户登录和文本消息功能4寻址讯息按D addr的下面解决您的传出地址：|消息。
地址输入屏幕IMPT RQRP返回出现。
按U或V滚动地址列表。
或通过使用多抽头直接地址条目。
5附加一个优先级的报！或请求的答复地址：|在发送您的消息，您可以附加一个优先级的消息或请求回复您的信息。
IMPT RQRP返回按D下面IMPT到开启/关闭一个“优先”标志对于传出的信息。
一“优先”标志图标显示在顶部切换时，屏幕上。
见“TMS的地位的象征”第88页。
按E到下面RQRP打开/关闭“要求回复“图标传出消息。
“请求回复”状态图标显示在屏幕的顶部时，翻转的。
见“全方位维修计划地位的象征“第88页。
ASTRO卫星XTS 2500Ⅲ型93ARS的用户登录和文本消息功能注意：当您收到一份关于XTS 5000无线电消息与“请求回复”图标标记，你必须手动响应您已收到发件人该消息。
该系统将不会自动发送回的无线电接收通知等信息。
注：“优先”在信息标志不意味着消息将获得比其他高优先级的消息当它被传播。
这仅仅是一个迹象表明，可以嵌入到一个信息，让接收器知道这个消息是重要的。
单板
OptiX OSN 3500/2500/1500 智能光传输系统 设备手册
目录Biblioteka 5.6 STM-1 电接口单元 SEP/SEP1/EU08/EU04/OU08/TSB8/TSB4 ...................................... 5-31 5.6.1 功能 ....................................................................................................................... 5-32 5.6.2 原理 ....................................................................................................................... 5-33 5.6.3 面板说明 ................................................................................................................ 5-34 5.6.4 单板保护配置......................................................................................................... 5-35 5.6.5 单板参数配置......................................................................................................... 5-39 5.6.6 版本说明 ................................................................................................................ 5-40 5.6.7 技术参数 ................................................................................................................ 5-40
SaltDogg PRO2500CH 系列电动扔物箱吐送器说明书
Installation InstructionsPRO2500 &PRO2500CH Series SaltDogg®Electric Drive Poly Hopper Spreader2.5 cubic yardsU.S. Patent 9,562,333Table of ContentsGeneral Information (1)Safety Precautions (1)Installation Instructions ........................................................... 1-3Spreader Operation (4)Spreader Maintenance ............................................................4-5Warranty Information (5)Repair Parts & Drawings .........................................................5-8General InformationOverall Length: 116.5 inchesOverall Width: 48 inchesOverall Height: 44.3 inchesEmpty Weight: 986 lbs.Capacity Struck: 2.5 cu. yd.Vehicle RequirementsTrucks with minimum GVWR 13,000 lbs. (8 ft. bed), 150 AMP orhigher alternator is recommended.Average Material WeightsThis spreader is restricted to the use of dry, free-flowing salt,sand, and sand/salt mix. Do not run other materials through thespreader.Materials to use Weight (pounds per cubic yard)Fine Salt-Dry 2,250Coarse Salt-Dry 1,431Sand/Salt up to 50/50 Mix-Dry 2,700Note: To calculate the total spreader weight (including icecontrol material), add the empty spreader weight plus the icecontrol material and spreader accessories.CAUTIONDo not overload vehicle beyond the vehicle’s GVWR or GAWR.Check vehicle's load rating certification sticker for maximumvehicle capacity.WARNINGImproper installation and operation could cause personalinjury, and/or property damage. Observe the following SafetyPrecautions before, during and after operating this spreader. Byfollowing these precautions and common sense, possible injuryto persons and potential damage to this machine may be avoided.Safety Precautions1. Read the entire Installation Instructions before operating thisspreader.2. Read and understand all safety decals on the spreaderbefore operating.3. Check to make sure all safety guards are securely mountedinto place before operating this spreader.4. Verify that all personnel are clear of the spreader spray areabefore starting or operating this spreader.5. Do not over-load your vehicle beyond payload limits. If thereare any questions, contact the vehicle manufacturer.6. Do not adjust, clean, lubricate or unclog material jambswithout first turning off the spreader.7. Do not climb on or in the spreader during operation. Do notride on the spreader while the vehicle is in motion.8. Make sure the spreader is securely fastened to the vehicle inaccordance with this manual.9. Do not operate a spreader that is in need of maintenance orrepairs.10. Do not operate the spreader while ill, tired, or under theinfluence of alcohol or drugs.11. Batteries normally produce explosive gases which cancause personal injury. Always disconnect the battery beforeremoving or replacing electrical components.12. Do not leave unused material in hopper. Material canfreeze or solidify, causing spreader to not work properly, and/ordamage the unit. Empty and clean after each use.Installation Instructions1.Mounting the Spreader onto the VehicleA. Remove the tailgate from the vehicle (if equipped) as well asany other object which will interfere with the spreader.B. Check truck’s bed for all kinds of sharp debris or foreignobjects. They can cut and seriously damage poly hopper.C. Remove chute, hardware kit from inside spreader. If spreaderhas been used make sure there is no material left in the hopper.D. Lift spreader using all tie downs (Fig. 1), or using fork lift.Lower spreader into the truck bed.G. Slide spreader forward or backwards to make sure that chute doesn’t interfere with any part of the truck. Remove one pin and rotate chute as shown in Fig. 4. Make sure that chute doesn’t hit any part of the truck.H. Measure the distance from the front of the truck bed to the front of the hoppers front legs. Fabricate spacer to fit between front of the spreader and front of the bed using 2 x 6 boards and install it between the spreader and truck bed front wall as shown in Fig. 5I. In addition, secure spreader using four ratchet straps. Tighten straps evenly. (Fig 5.1)Fig. 5Fig. 5.1E. Connect the 2-pin connector on the power cable to the control box mating connector.F. Connect wire harness single connectors to control box connectors.G. Connect fuse connector to the fuse terminal or ignition switch (5 AMP max).H. Lay out a path for the power cable to the battery, use quick ties to secure power cable. DO NOT CONNECT TO BATTERY AT THIS TIME!I. Lay out path for wire harness to the rear of the vehicle. Stay clear of the exhaust system. Excess heat can damage the wire harnesses. Use quick ties to secure harness to underbody.J. Connect the wire harness to the motors and vibrator. Make sure wire colors on wire harness match colors on the motor.K. Thoroughly clean battery terminals. Make sure battery terminals have no tarnish or corrosion. DO NOT CONNECT WIRE HARNESS TO DAMAGED OR CORRODED TERMINALS! IT MAY RESULT IN OVERHEATING, LOST POWER AND POTENTIAL CONTROLLER DAMAGE! Install the circuit breaker within 12" from the battery. Connect red wire from cable 3035935 and battery cable 3001379 to circuit breaker according to the breaker markings. Connect the power cable and battery cable directly to the battery. Make sure connection to battery terminals is good and tight. Loose connection to battery terminals will result in sparking, overheating and possible battery damage!L. Insure all functions of the controller are working properly.M. Observe auger/ chain moving in proper direction. If direction is wrong reverse wires between Motor and Wire Harness.N. Optional spot light (5 AMP max) can be installed on spreader. Use utility light kit part number 3018009. Remove cap from single white wire. Connect light to this wire and the trucks frames known ground (negative).2. Control Box and Vehicle Wiring Harness InstallationNote: Make sure you have connected the proper wire color. This is a wire ground electrical system! No Connections to truck’s frame or body allowed!Note: Always disconnect battery before attempting to install electrical components on your vehicleA. Mount the controller in a convenient location in the truck cab. It is recommended not to mount the controller directly in front of heat vents. Allow ample air space around controllerCAUTIONInspect straps and hardware after each time spreader is loaded. Tighten straps and hardware if necessary.CAUTIONDo not mount controller in the way of air bag deployment!WARNINGImportant! Do not use ratchet straps or tailgate latch exclusively! Always use spacer!WARNINGDo not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling. To insure good performance of your spreader, check the condition of truck’s electrical system. Using digital voltmeter, check alternator and battery voltage. With engine running and head lights and heater fan ON good voltage reading should fall between 13.0 and 15.3 volts. If voltage reading falls out of this range, check and adjust your electric system.IMPORTANTMake sure all wires securely attached to vehicle or spreader. Use wire ties and/or wire clamps to attach wires. All excess wires must be rolled into bundles and attached to vehicle or spreaderB. Route both wire harnesses into truck cab through firewall (it maybe necessary to drill holes). Insulate hole to avoid water leaks.C. Insure no wires are nicked or damaged during installation.D. Connect the 4-pin connector on the wire harness to the control box 4-pin connector.301694402037003035935CB150PB 3001379BATTERY POSITIVEBATTERY NEGATIVECONNECT TO FUSE OR WIRE IN FUSE PANEL,CONTROLLED BY IGNITION SWITCHLoosen Screws, Rotate Shields to Adjust Spray PatternUnscrew Bolts, Slide Lower Chute Up or Down Into Desired Position,Reinstall & Tighten BoltsSpreader MaterialsSpreader Operation1. PRO2500 is equipped with a dual independent speed controller. To start spreader, press “POWER” switch. Switch will be illuminated. Auger/ chain and spinner will start rotating. Auger and spinner can be adjusted independently.2. To activate vibrator press “VIBRATOR” switch, vibrator switch will illuminate. Vibrator can operate continuously for 30 min max with 15 min brakes to avoid overheating.3. To stop spreader press “ON-OFF” switch again.4. PRO2500 controller is equipped with electronic overload and current spike protection. Controller is not serviceable.Controller has two LED lights: “ERROR” and “FLASH NUMBER”. If there is a problem the ERROR LED will illuminate and FLASH NUMBER LED will give a series of flashes. Count the number of flashes and refer to the troubleshooting guide provided with the controller. Additionally you can go online for the troubleshooting codes at https:///media/3802/3026671_A.pdf 5. Spreading pattern can be controlled by repositioning of the baffles on the chute as shown in Fig. 6. Chute heights can be adjusted to accommodate different vehicle heights (Fig.6).The density of materials that can be loaded into the spreader varies and therefore so will the amount of a given material that can be carried by the spreader before the maximum load rating is reached.1. Ensure that the spreader is securely mounted to the vehicle and that the top screen is installed and secured in the hopper.2. Remove the tarp, if used.3. Determine the amount of material that you can safelytransport using your vehicles GVWR/GAWR and the following table on page 1.4. Fill the spreader evenly with your material, making sure not to fill past the top of the hopper.Fig. 66. Check the Feed Chain tension periodically. To check the tension, measure in 21"-25" from the rear edge of the gear box mount. Push up on the chain with your hand. The conveyor chain should lift up 2"-3" off the conveyor chain guide or cross angles (Fig. 7).Feed ChainRear of Sill Extension2" - 3"21" - 25"Fig. 7WARNINGNever attempt to lift spreader with material in hopper!WARNINGNever leave material in hopper for extended period of time. Material can freeze, solidify and seriously damage the spreaderIMPORTANTOnly use dry salt, sand, sand/salt, or cinder/salt mixes in the spreader. Other materials could cause damage to the machine.IMPORTANTWhen filling the spreader, do not exceed the gross-vehicle-weight rating (GVWR) or gross-axle-weight rating (GAWR).IMPORTANTOverfilling the hopper could damage the spreader & your vehicle.Spreader Maintenance1. Wash spreader after every use. Make sure no material is left under auger/ chain and/or inside trough.2. Inspect and retighten fasteners after every 5-7 hours of operation.3. Lubricate bearings every 7-10 hours of operation using general automotive grease.4. Inspect terminals/connectors every time you disconnect spreader from wire harness. Apply thin layer of dielectric grease on terminals. If any tarnish/corrosion is found, clean terminals and apply dielectric grease.5. Use dielectric grease on all electrical connectors before an electrical connection is made or after connector is disconnected6. Empty the spreader of all ice control materials when not in use. Wash out the spreader to prevent material builds up.7. It is recommended to cover spreader with the tarp during storage periods.End of Season Maintenance1. Wash spreader. Make sure no material or residue is left in and outside the hopper.2. Lubricate bearing using general automotive grease.3. Inspect wire harness, connectors for broken insulation, missing components. Replace if necessary.4. Apply dielectric grease on all electrical connectors.5. Store hopper indoors, in a dry, cool place.6. Remove controller from truck. Store controller indoors, in a dry cool place.7. Inspect wire near connectors. Check for broken or missing insulation. Check for tarnished or corroded wires. Trim corroded wires and replace connectors if necessarySummer Storage1. Apply dielectric grease or similar protective compound on all electrical connectors & protect them with caps before storage.2. Disconnect and remove speed controller from vehicle and store it in dry and cool place. Protect controller from excessive heat and moisture.3. Clean hopper and trough from all kinds of debris.4. Remove, thoroughly lubricate and reinstall trough bearing.5. Protect hopper from excessive temperatures during summer storage.AccessoriesPRO2500 is supplied with tarp 3030857. To insure proper tarp operation, attach tarp to all hopper posts as shown below.Repair Parts - Standard Chute Assembly Part # 3031475Bill of MaterialsITEM PART NO.QTY.DESCRIPTION130308681UPPER CHUTE WELDMENT230309301CHUTE OUTER, POLY330309081MOTOR MOUNT CHUTE430309071MOTOR 12 VDC, .5 HP SPINNER5FCS038016075SS8SCREW, HHC-3/8-16 X 3/4 SST630123931SPINNER, 14" POLY CW730250651BUSHING STRAIN RELIEF8FWF025063007SS4WASHER, FLAT 1/4 SAE SS9FCS025020075SS2SCREW, CAP 1/4-20 X 3/4 SST1030085492SCREW,HEXHD CAP 1/4-20X.5 SST 1130309272SHIELD, CHUTE1230317553PLASTIC HEAD THUMB SCREW 3/8-16X3/4 SST 1330071154WASHER, FLAT 3/8 X 1.5 X.048 SST14FWL038069009SS4WASHER, LOCK RHS-3/8 SST1530071131PIN, CLEVIS, 5/16 X 2-1/2, .141 HOLE ZN 1630149941PIN,COTTER,1/8IN X 1IN SST12345678910111213141516 CAB SIDE LABELSECURE TARP ON SPREADERATTACHING BUNGEE CORDTO ALL POSTSRepair Parts - PRO2500 Auger Hopper AssemblyBill of MaterialsITEMPART NO.QTY.DESCRIPTION 130307631HOPPER PRO2500230329991TROUGH WELDMENT PRO25003300711512WASHER, FLAT 3/8 X 1.5 X.048 SST 4FWL038069009SS 16WASHER, LOCK RHS-3/8 SST 5FCS038016075SS12SCREW, HHC-3/8-16 X 3/4 SST 614102001BEARING, FLANGED 1-1/8"730012554NUT, HEX FLNG-3/8-16 SST 830330031SPACER, GEAR MOTOR930245751GEAR MOTOR CONVEYOR 12 VDC 1030336601AUGER PRO 5.25 VARIABLE LH 1130336631SLEEVE, AUGER ADAPTER12FCS038016100SS 8SCREW, HHC 3/8-16 X 1 304 SST 13FWF038100007SS 4WASHER, FLAT 3/8 USS SST 14FNE038016044SS20NUT, NYLOCK 3/8-16 X 7/16 SST 1530012501SCREW, HHC-1/2-13 X 3 SST 16FNE050013053SS1NUT, NYLOCK 1/2-13 SS 1730330701BRACKET BEARING FRONT1892400861BEARING, 1-1/4 FLANGE 2 HOLE 19FCB037516100SS4BOLT, 3/8-16 X 1 CARRIAGE SST 2030222204TIE-DOWN WELDMENT 2130308542CROSS MEMBER22300514012SCREW, HH1/2-13X 3.5, GR 5 ZN 23FWF05010601012WASHER, FLAT 1/2" SAE ZINC 24FNE05001305312NUT, NYLOCK 1/2-13 ZINC 2530308631INVERTED VEE, PRO25002630311731BRACKET VIBRATOR2730074161VIBRATOR 200 LBS 12 VDC ITEMPART NO.QTY.DESCRIPTION2830311761PLATE WELDMENT, VIBRATOR29FCS038016150SS4SCREW, HX HD CAP 3/8-16 X 1-1/2 SST 3030311691SHROUD31FWF025063007SS 2WASHER, FLAT 1/4 SAE SS 32FCS025020075SS2SCREW, CAP 1/4-20 X 3/4 SST3330331652STUD THREADED 5/16-18 X 2.5 SST 3430067192NUT, HEX FLANGE - 5/16-18 SS 3530312031MOUNT CONNECTORS3630075227SCREW, SHEET MTL #12x1.0 HEX WASHER HD SS'f 3730312762CLIP ATTACHMENT, CONNECTOR DEUTSCH 3830325911DECAL, DANGER, MOVING CONVEYOR/AUGER 3930325951DECAL, CAUTION, MOUNTING 4030330761CHUTE ATTACHMENT4130121444BOLT, CARRIAGE, 5/16-18 X 1 SST 42FNE031018034SS4NUT, NYLOCK 5/16-18 SS4330353461RIGHT ANGLE JUNCTION BLOCK4430353572SCREW SOCKET HD, RND 8-32X 1.50 SST 4530353582NUT, NYLOCK 8-32 SST, BLACK OXIDE 468002GREASE FITTING, 1/4 STD4730353472GREASE FITTING 1 MTU BE 1/8 NPT STRAIGHT 4830357422BUSHING SNAP THICK PANEL4930353442GREASE FITTING 1 MTU BE 1/4-28 MALE STRAIGHT 5030353591GREASE TUBE REAR BEARING AUGER 5130360161GREASE TUBE FRONT BEARING AUGER 5243753CLAMP , HOSE .4375, 9/32 HOLE 5330358541LABEL PATENT5430331721DECAL CONNECTION1234 56 78 9 10 111213 14 15 1617 18 19 20 212223 24 2526 272829 3031 32 333435 36 37 3839404142 43 44 45 46 47 4849 5051 525354Repair Parts - PRO2500CH Chain Hopper AssemblyBill of MaterialsITEMPART NO.QTY.DESCRIPTION 130307631HOPPER PRO2500230331641WIPER BRACKET 330352691WIPER BELT, FRONT4300752212SCREW, SHEET MTL #12x1.0 HEX WASHER HD SS'530277721TROUGH CHAIN PRO5006300711512WASHER, FLAT 3/8 X 1.5 X.048 SST 7FWL038069009SS16WASHER, LOCK RHS-3/8 SST 830138211GEAR MOTOR CONVEYOR 12 VDC 9FCS038016100SS8SCREW, HHC 3/8-16 X 1 304 SST 1014102001BEARING, FLANGED 1-1/8"1130314832BOLT, 3/8-16 X 1 CARRIAGE SHORT NECK SST 12FNE038016044SS14NUT, NYLOCK 3/8-16 X 7/16 SST 13KS4022KEY, 1/4 X 1/4X21414102502SPROCKET, 6 TOOTH PINTLE CHAIN 151401100P 1CHAIN ASSY D662 122 LINKS 1630085711SHAFT IDLER, ASSEMBL Y 1714110012BEARING, IDLER TAKE UP 1830230462BOL T, WELDED TAKE UP 1930230222SPRING CHAIN TENSION 2030311992TAKE-UP NUT WELDMENT21FNH063011054SS2NUT, HH 5/8-11 X 17/32 HIGH SST 2230311951CHAIN COVER23FWL025050006SS 4WASHER, 1/4 IN. SPRING LOCK SST 24FCS025020075SS6SCREW, CAP 1/4-20 X 3/4 SST 2514102411WIPER BELT, HOPPER26FWF025063007SS7WASHER, FLAT 1/4 SAE SS2730085495SCREW,HEXHD CAP 1/4-20X.5 SST 28FNE025020031SS5NUT, NYLON INSERT 1/4-20 SST 2930222204TIE-DOWN WELDMENT 3030308542CROSS MEMBER31300514012SCREW, HH1/2-13 x 3.5, GR 5 ZN 32FWF05010601012WASHER, FLAT 1/2" SAE ZINC ITEM PART NO.QTY.DESCRIPTION3430308631INVERTED VEE, PRO25003530311731BRACKET VIBRATOR3630074161VIBRATOR 200 LBS 12 VDC 3730311761PLATE WELDMENT, VIBRATOR38FCS038016150SS4SCREW, HX HD CAP 3/8-16 X 1-1/2 SST 3930353461RIGHT ANGLE JUNCTION BLOCK 408003GREASE FITTING, 1/4 STD4130353572SCREW SOCKET HD, RND 8-32X 1.50 SST 4230353582NUT, NYLOCK 8-32 SST, BLACK OXIDE4330353473GREASE FITTING 1 MTU BE 1/8 NPT STRAIGHT 4430353441GREASE FITTING 1 MTU BE 1/4-28 MALE STRAIGHT 4530353452GREASE FITTING 1 MTU BE 1/4-28 MALE 90 DEGREE 4630353481GREASE HOSE REAR BEARING 4730360511GREASE HOSE FRONT DR SIDE 4830360521GREASE HOSE FRONT PS SIDE 4950003HOSE CLAMP , .375 DIA 5030311691SHROUD5130312031MOUNT CONNECTORS5230312762CLIP ATTACHMENT, CONNECTOR DEUTSCH 5330330761CHUTE ATTACHMENT5430121444BOLT, CARRIAGE, 5/16-18 X 1 SST 55FNE031018034SS4NUT, NYLOCK 5/16-18 SS 5614990352LABEL, WARNING 35714990301LABEL, CAUTION 1 (PAYLOAD)5830325911DECAL, DANGER, MOVING CONVEYOR/AUGER 5930325931DECAL, DANGER, CONVEYOR 6030325951DECAL, CAUTION, MOUNTING6130331652STUD THREADED 5/16-18 X 2.5 SST 6230331721DECAL CONNECTION6330067192NUT, HEX FLANGE - 5/16-18 SS 64FCS038016075SS 12SCREW, HHC-3/8-16 X 3/4 SST12 3 456 78 9 10 11121314 15 16 17 18 19 20 21 22 2324 25 26 27 28 29303132333435 36 3738 3940 4142 43 4445 46 47 484950 51 52 53 545556 57 5859 60 6162 63 64Repair Parts - PRO2500CH SpreaderRepair Parts - PRO2500 SpreaderBill of MaterialsBill of MaterialsITEMPART NO.QTY.DESCRIPTION130333011HOPPER ASSEMBL Y PRO2500230314751CHUTE SWING ADJ 330308531TOP SCREEN PRO2500430317971HARDWARE KIT PRO2500530169341CONTROLLER SPEED 12 VDC, 60 AMP 630306281WIRE HARNESS MAIN730359381KIT POWER CABLE REPLACES 3016943830359351POWER CORD930013791CABLE, SCH BATTERY 14 IN. (RED)10CB150PB 1BREAKER, 150 AMP .1102037001WIRE ASSEMBLY, 36 LONG12149650511HOLD DOWN KIT, SPREADER (4 STRAPS)1330308571TARP PRO25001430331742PIN, CHUTE ATTACHMENT15660504SNAPPER PIN, 1/4 X 2, YLW ZINC 1630360151LABEL SERIAL NUMBER PRO2500ITEMPART NO.QTY.DESCRIPTION130307661HOPPER ASSEMBL Y PRO2500230314751CHUTE SWING ADJ 330308531TOP SCREEN PRO2500430317971HARDWARE KIT PRO2500530169341CONTROLLER SPEED 12 VDC, 60 AMP 630306281WIRE HARNESS MAIN730359381KIT POWER CABLE REPLACES 3016943830359351POWER CORD930013791CABLE, SCH BATTERY 14 IN. (RED)10CB150PB 1BREAKER, 150 AMP .1102037001WIRE ASSEMBLY, 36 LONG12149650511HOLD DOWN KIT, SPREADER (4 STRAPS) BLA 1330308571TARP PRO25001430331742PIN, CHUTE ATTACHMENT 15660504SNAPPER PIN, 1/4X2, YLWZINC 1630360151LABEL SERIAL NUMBER PRO2500231516156891011 121314131556891011121314216。
Spheros North 美国水热器和水泵产品说明书
Information concerning all warranties may be obtained by calling (734) 218-7350 ext 103 or 112. Toll free (888) 9604849.
Owner’s Responsibilities:
Seห้องสมุดไป่ตู้vice heater at the start of each season. While such maintenance may be performed by any company, improper or incorrectly performed maintenance or repair voids this warranty. Service parts including fuel nozzles, filters and overheat fuses are not covered under warranty.
BTG2500中英文使用说明书
Shinn Fu Australia Pty. Ltd. 汽车搬运平台杆 G2500 产品说明书
OWNER'S MANUALWORKING LOAD LIMIT 2500KGGARAGE JACKModel No: G2500THIS NEW JACK CONFORMS TO MANDATORYASNZS 2615:2004 STANDARDSafe Instructions OperationSpecifications MaintenanceCAUTION:Carefully Read Instructions and Procedures for Safe OperationsSAFE INSTRUCTIONSINSTRUCTIONSThis hydraulic trolley jack is designed to be used with a 125mm diameter head cap, and a handle length of 1330mm length.1. Before Each UseVisual inspection should be made before each use of the garage service jack for abnormalconditions such as cracked welds, leaks and damaged, loose, or missing parts.2. After Each UseGarage jack should be inspected immediately if the lift is believed to have been subjected to an abnormal load or shock. It is recommended that inspection be made by manufacturer’s or supplier’s authorized repair facility.3. Annual InspectionAnnual inspection of the garage jack is recommended and shall be made by themanufacturer’s or supplier’s nominated repair facility to ensure that your garage jack is inoptimum condition.RECOMMENDATION FOR SAFE USAGE OF THE JACK1. The hydraulic trolley jack should be used on a hard level surface and be free to roll duringlifting and lowering.2. The unlifted wheels of the vehicle should be chocked.3. The load should be centrally located on the head cap.4. No person should remain in a vehicle that is being lifted.5. The hydraulic trolley jack should be used for lifting and lowering only; the raised vehicleshould be supported on vehicle support stands.6. No person should get bodily under a vehicle that is supported by a hydraulic trolley jack.7. The vehicle manufacturer owner's manual should be consulted prior to the lifting of thevehicle.8. Make sure that lift point is stable and properly centered on jack saddle.9. Vehicle should be clear of all passengers. Transmission should be in gear (or park forautomation transmission) and the emergency brake should be engaged.10. Familiarize yourself thoroughly with this owner manual before operation to prevent damageto jack and property, or personal injury.Front Castor Rear CastorHandle ForkRelease ValveGear Handle AssemblyHydraulic PowerUnit Saddle TO RAISE:Place vehicle in park, apply brake and chock wheels with suitable devices.1. Position the jack under the load and close releasevalve by turning clockwise firmly.2. Operate manually by pumping with handle untilsaddle ALMOST contacts with vehicle. Check tosee that the saddle is centered and will contact theload lifting point firmly.3. Continue to pump jack handle until load is raised todesired height and immediately transfer load toappropriately rated jack stands.TO LOWER:1. Raise load sufficiently to remove support devices,then slowly turn handle counterclockwise until loadbegins to lower. Carefully control the rate ofdescent and avoid shock load created by openingand closing valve quickly. This may result inoverloading hydraulic circuit causing damage to jackand personal injury.2. Remove jack from under load and if necessary,Model No. : G2500Working Load Limit: 2,500kgHeight Lowered: 135mmHeight Raised: 495mmJack Dimension: 640mm x 345mm x 195mm Handle Length: 1,330mmVolume of Oil: 180ccNet Weight: 34kg push saddle down fully to reduce piston and ram exposure to contamination.OPEARTION Know Your JackSPECIFICATIONImportant:When adding or replacing oil,ALWAYS use good grade Hydraulic Jack oil. DONOT use Hydraulic Brake Fluid, Alcohol, Glycerin,Detergent, Motor Oil or dirty oil. Use of animproper fluid can cause serious internal damageto your jack.ADDING OIL• Position the jack on level ground and fullylower the saddle. Remove oil filler plug.• Turn jack over and drain old oil out throughthe oil filler plug hole.• Refill with new oil through the oil filler plughole. Not allow dirt or other foreignmaterials to enter the hydraulic systemwhen filling.• After refilling, remove any air from hydraulicsystem by opening the release valve andrapidly pumping the jack handle severaltimes.• Put the oil filler plug back and the jack isready for use.• Add lubricating oil to all moving part asneeded.• Check ram and pump plunger every fewmonths for any signs of rust or corrosion.Clean as needed by wiping with oily cloth.• When not in use, ALWAYS store jack withsaddle and pump plunger lowered all theway down.POSSIBLE PROBLEMS POSSIBLE CAUSESJack will not liftloadJack will liftload, but will notholdJack will notlowercompletelyPoor jacklifting. Pumpfeels spongyJack will notlift to fullheightHandle raisesby itself whenjack is underloadAND SOLUTIONS(Refer to Operation andMaintenance proceduresfor detail information)X Release valve not tightly closed. To close or tighten, turn release valve clockwise.X X X X Air is in hydraulic system. Release air from system.X X X X Oil level is low in jack. Add oil as required.X 1. Oil reservoir is overfilled. Drain out someoil.2. Lubrication of movingparts is necessary.X X X Power unit is malfunctioning. Replace the power unit.MAINTENANCEMAINTAINING OIL LEVELLUBRICATIONPREVENTING RUSTPRODUCT NO.:G25002,500 KG GARAGE JACKMANUAL12345678910111241314151617181920212223242526272829301572737547484344744232333437383940413536374950535554555656575859575251616264636566676866676876706971636468G25001G489-30020-0001G489-30024-0000G489-30023-0000G489-30006-0000G489-30022-0000G489-30025-0000G489-30004-0003G489-30003-0000F348-30007-0000G489-30001-0000G489-30005-0000F348-30002-0000F361-30030-0000G489-30014-00001623-06350-2431623-09530-243BASE 2O-RINGRESERVOIR BACK-UP WASHER O-RING CYLINDER BACK-UP WASHER BUCHING COVER U-CUP-RAM TOP NUT BALL O-RING WASHER OIL FILTER 345678910111213141516ITEM QTY DESCRIPTIONPARTCODE ITEM QTY DESCRIPTIONPARTCODE 112111*********G489-30012-0000G489-30013-0000G489-30011-0000G489-30010-0000G489-30009-0000G489-30008-0000G489-30029-00001413-00006-2431103-06012-204G489-31000-0380G489-30021-0000G489-30027-0000G589-30015-0421GASKET COVERING LOCK WASHER SCREW SCREW PUMP PISTON BACK-UP WASHER GUARD SCREW OIL SEALSCREW SAFETY VALVE SAFE SPRING 181920212223242526272829O-RING 30SCREW11111111111111RAM PLUNGER G489-40004-0411G489-40003-100032RELEASE VALVE CONNECTING BAR RELEASE VALVE GEAR3311BALL NUT 3411317-00010-0313511401-00008-031WASHER 3637383940414243441511112111529-20010-0311413-00010-2041103-10016-031G489-20008-0410G489-40001-0410G589-40001-1000G489-10002-0421G489-12000-1000G95L-12000-0000RETAINER SCREWRETURNING SPRING PINLOCK WASHER HANDLE FORK RETURN SPRING LIFT ARM ASSY SADDLE 474849505152535455565758592112211221224G489-10001-1000G489-20004-0410G489-22000-1000G489-21000-10001303-00008-0311413-00008-204G489-20007-0410G489-20005-04101413-00020-204G493-20001-04101413-00012-204G489-20006-04101317-00012-031STUD RADIUS LINK RIGHT SIDE PLATE LEFT SIDE PLATE LOCK WASHER NUTLEFT HANDLE BOLT LOCK WASHER 616263646566224124G489-23000-0000G489-24000-00001413-00010-2041302-00010-031G070-20002-0410G489-20001-1000BEARING ASSY .REAR CASTER ASSY LOCK WASHER NUTFRONT AXLE FRONT WHEELSCREW RIGHT HANDLE BOLT NUTRADIUS LINK LOCK WASHER FRAME TIE RODG25006768HANDLE ASSY .70717273747576ITEM QTY DESCRIPTIONPARTCODE 1401-00018-0311438-00015-204WASHER SNAP RING-E SCREW O-RINGHANDLE II RELEASE VALVE ASSY RETAINER FILTERFRAME TIE ROD2269G489-41000-1002G489-40002-10011103-06034-031G489-30015-0000G489-32000-00001529-40035-031F361-30007-0000 G489-20003-041011111111。