TURCK IM系列 隔离栅 模块化接口技术
TURCK远程IO技术方案
防护等级：IP65
箱体尺寸：650*500*210（mm）
箱体材质：整体不锈钢板焊接
电缆穿线孔：M20，带螺纹锁紧端子
进线方式：箱体下端
安装方式：壁挂式或立柱安装
5、系统组态及产品培训
系统软件组态、编程、调试及系统集成由甲方在乙方技术人员的协助下独立完成，由甲方提供具体工艺要求，乙方负责最终组态文件的可靠性、实用性。组态地点在甲方的安装现场完成（或在产品培训期间，在培训地点同时完成），组态数据的下装调试在甲方的操作员站上完成，最终达到整个系统的运行条件。
3.6I/O硬件配置及报价
根据用户的控制要求及I/O点数，具体的I/O子站的配置如下：
设备名称
型号说明
实际数量
单价
(万)
合计
MT18-R024
excom®16 I/O槽母板
3
PSD24EX
excom®电源
6
GDP-IS
excom®网关
6
AI40EX
4点4-20mA输入模块
21
TI40EX
4点温度输入模块
每个母板可连接2个冗余网关和16个I/O模块，每个温度模块有4点温度，
所以每个底板最大可连接64点温度。
总线与I/O模块之间完全隔离，每个通道直接完全隔离，互不干扰。
内/外总线、通讯网关及电源均可冗余配置。
所有模块均可带电插拔，每个模块的更换不影响其它信号的正常传输。
无需安全栅及DCS/PLC的I/O模块。
TURCK总线式本安远程I/O系统—excom®
技术方案
德国图尔克（天津）传感器有限公司
2010年11月02日
1、项目基本情况
2、设计方案说明
本质安全快速选型指南
温度等级 NEC505/CENELEC/IEC T1
T2
T3
T4 T5 T6
NEC500 (Division区域防爆标志)
Class I Div 1 Groups A, B, C, D T4
可燃气体或蒸汽 区域分类
Class I
气体分组
温度等级
NEC505 (Zone区域防爆标志)
Zone 0 A Ex ia IIC T4
注：见下表区域划分
CENELEC/IEC Zone 0 (Zone 20-粉尘) Zone 1 (Zone 21-粉尘)
Division 2
温度
NEC500 T1 T2 T2A T2B T2C T2D T3 T3A T3B T3C T4 T4A T5 T6
Zone 2
Zone 2 (Zone 22-粉尘)
2 5
现场总线电缆规格 在IEC 61158-2标准和ISA-S50.02第二部 分物理层标准中，对现场总线H1数据传输 介质的规格进行了定义。同样的标准也出 现在了FF现场总线规范中传输速率低于 31.25Kbps的物理层文件FF-816-1.4中。 适用于现场总线的电缆有四种基本类型 （见下表）。新系统安装首选A型电缆， 因为它的允许安装长度最大。其它类型电 缆适于替代已有的4-20mA控制系统的电缆。
通讯参数。没有诊断模块，DPC系统也能正 常运行，在这种情况下，现场设备可以提供 一些简单的诊断信息。
现场设备收集的整理信息，通过高速以太网 接口模块传输给更高级别的总线设备（如主 机），作为诊断和报警数据。诊断模块可以在 系统上电情况下插入和拔出（支持热插拔）。
本质安全: 快速选型指南
温度转换器
温度测量是非常普遍的应用，在危险区也是如此。 IM34温度转换设备集高级诊断，功能全面，使用方便 和易于操作的优点于一身。
Turck EZ-track线性位置技术Q21-DQ产品介绍说明书
Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | B1027 B19Linear Position TechnologyEZ-trackL i n e a r P o s i t i o n T e c h n o l o gyDirect Quadrature Output:Directly interface to the PLC input card and reduce installation time, vendors and cost. The Q21-DQ provides A and B channel quadrature output signals that are proportional to theposition of the magnet assembly along the length of the probe, and output directly from the transducer to the controller. The quadrature output makes it possible to directly interface to virtually any incremental encoder input orcounter card, eliminating costly absolute encoder converters and special PLC interface modules.An index channel (Z) is also provided and its position may be set by the user at any position along the active system. The A, B and Z channels are differential outputs: the connection for each output consists of two signal wires. These are typically described as the “+” and “-” signals. Differential signals are much less prone tointerference caused by electrical noise or ground loops often found in single ended connections.Replace Incremental Output Devices:The Q21-DQ may be used in certain applications to replace incremental rotary and linear encoders. The quadrature output may be used in applications requiring 0.001 inch resolution and repeatability.Velocity Feedback:The EZ-track quadrature produces pulses that are sent to the controller in packets at a fixed frequency. The period of the pulses does not change with magnet velocity. Therefore, velocity cannot be determined from the pulse packets unless the controller can interpolate velocity from position over time. If your application requires a velocity feedback, please consider the Linear Encoder on pages B32-B37 or consult factory.Incremental Output, Absolute Functionality:The Q21-DQ allows you to use an incremental output, while taking advantage of an absolute sensing technology. The Burst Input on the transducer triggers a data transfer of all incremental position data relative to thetransducer’s zero position. This can be used to achieve absolute position updates when power is restored to the system or anytime an update is needed to re-zero or home the machine. Programmable Zero Point:The zero input allows you to set the probes reference position at any point along the active span . The probe will output an increasing or decreasing signal based on the direction the magnet is moving in relation to the established zero point. See Quadrature Part Number Key to select storage mode.Volatile Storage:The zero point will be kept until a new zero pulse is sent or until the probe loses power.The zero point can be programmed an infinite number of times.Non-Volatile Storage:The probe will store the zero position even in the event of a power failure. The zero point can be set 100,000 times.Transducer Inputs:The burst and zero inputs are single ended connections: the connection for each inputconsists of only one wire. The Q21-DQ is available with either +24 VDC level signal or TTL level thresholds. Additionally, the 24 VDC may be specified as either sinking or sourcing relative to the probe’s input.Quadrature Output Resolution and Speed:The internal resolution of the Q21-DQ transducer is 0.001 inches. This would be represented to the encoder input device by specifying an output resolution of 1,000 cycles per inch (CPI).Frequency or Pulse Rate:For a typical incremental encoder output, the resolution of the encoder and the speed of travel govern the frequency and pulse width of the output pulses. The output pulse rate from the EZ-track transducer is fixed and controlledinternally. This output frequency is user specified (10 kHz to 1 MHz) so that it does not exceed the maximum input rate of the counter card. If the controller’s maximum input frequency falls between two available frequencies, choose the lower frequency.Output Drivers:The Q21-DQ uses an OL7272 line driver and may be configured for either a TTL level output or a 10-30 VDC level output. Option R has a 5 VDC TTL level output regardless of input power. Option L has an output of 1 volt less than the probe’s input voltage and should be used when driving input cards that are not TTL compatible.Linear Position TechnologyEZ-trackB20 B1027Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | Note: In addition to the LDT, a typical system includes a magnet, mounting feet and cable (all sold separately).Dimensions: Q21-DQ Quadrature Profile SeriesWiring Diagram: Q21-DQ/ Q35-DQMating Cordset: RKC 12T-*/S618Dimensions: Q35-DQ Quadrature Profile SeriesOR RD BU PK GY YE TN GNBN WHNote: Self contained piston with magnetpermantly attached。
图尔克 TBEN-L5-16DXP 以太网多协议 I O 模块 用户手册说明书
3:20+02:00紧凑的以太网多协议 I/O 模块16个通用数字通道，可配置为PNP输入或2 A输出TBEN-L5-16DXP型号TBEN-L5-16DXP 货号6814088系统数据供电电源24 VDC 允许范围18…30 VDC最大总电流，每个电压组最大9 A 总电流V1 + V2最大11 A连接供电电压5针公头7/8”接插件X1工作电流V1: max. 150 mA 传感器/执行器供电端口 C0-C3 由 V1 供电短路证明， 每端口 120 mA 传感器/执行器供电端口 C4-C7 由 V2 供电短路证明， 每端口 120 mA 电气隔离电压组V1和V2电隔离，电压最高500 VAC 典型功率损耗ð 10 W系统数据现场总线传输速率10/100 Mbps 现场总线连接技术2 × M12，4针，D型诊断协议自动网络服务器默认：192.168.1.254服务接口通过P1或P2连接以太网BEEP功能支持字段逻辑控制器(FLC)ARGEE固件版本 3.2.9.0ARGEE工程版本 2.0.24.0Modbus TCP 地址静态IP，DHCP支持功能代码FC1, FC2, FC3, FC4, FC5, FC6, FC15, FC16, FC23TCP连接的数量8输入登记起始地址0 (0x0000 hex)输出登记起始地址2048 (0x0800 hex)■PROFINET设备、EtherNet/IP设备或Modbus TCP主站/从站■集成式以太网交换机■支持10 Mbps/100 Mbps■2个M12 4针D型以太网现场总线接头■PROFINET S2系统冗余■增强型玻璃光纤外皮■冲击和振动测试■全密封模块电子元件■防护等级IP65、IP67、IP69K ■7/8"公头接插件，用于连接电源，5针■电隔离电压组■ATEX危险2/22区■每个输入端口都具有输出诊断功能■每路输出最大2 A■每个通道都具有输出诊断功能■每端口有两个可随意选择的数字通道■可编程ARGEE3:20+02:00EtherNet/IP 地址符合EtherNet/IP规范快插（QC）< 150 ms 设备级环（DLR)支持3级连接 (TCP)31级连接 (TCP)10输入配置实例101输出配置实例102配置配置实例106PROFINET 版本 2.35地址DCP 一致性分类 B (RT)最小周期时间 1 ms 快速启动（FSU)< 150 ms诊断依据PROFINET报警处理拓扑检测支持自动分配地址支持介质冗余协议（MRP）支持系统冗余S2网络负载等级3数字量输入通道数16Connectivity inputs M12，5针输入类型PNP 输入诊断类型组诊断开关阈值EN 61131-2 分类3, PNP 低电平信号电压< 5 V 高电平信号电压> 11 V 低电平信号电流< 1.5 mA 高电平信号电流> 2 mA 输入延迟 2.5 ms电气隔离与现场总线之间电隔离最高可耐500 VDC的电压数字量输出通道数16Connectivity outputs M12，5针输出类型PNP 诊断通道诊断输出电压24 VDC，来自电势组通道输出电流 2.0 A, 短路保护， 每端口最大 2.0 A 继电器输出 1.3 ms负载类型EN 60947-5-1:DC-13短路保护是电气隔离与现场总线之间电隔离最高可耐500 VDC的电压3:20+02:00标准 / 指令合规性振动测试符合EN 60068-2-6标准加速度最大20 g冲击测试符合 EN 60068-2-27认证滑落和翻倒符合EN 60068-2-31/EN 60068-2-32电磁兼容性符合EN 61131-2标准认证和证书CE，FCC，FM I类，2区，抗紫外线符合DIN EN ISO 4892-2A (2013)标准UL认证cULus LISTED 21 W2, Encl.Type 1 IND.CONT.EQ.有关ATEX/IECEx的注释必须遵守包含有关在爆炸危险2区和22区中使用的信息的快速入门指南。
Eaton 模块化通信出口、模块化墙板、模块化壁板插孔系列说明书
Modular connectivity point familiesModular connectivity pointsOur full line of modular communications outlets combined with modular wallplates deliver maximum fl exibility at connection points throughout the home. Modular jacks and adapters provide connection points for a variety of voice, video, data, and audio formats and are designed with quality, ease of installation and compatibility in mind.Modular wallplatesDecoratormodular mounting strap insertsPSECTIONShown: 5546-6WModular devices offer improved quality andperformance over pre-mounted devices, whether you are delivering connection points for video, c modular connectivity point solutions for today's needsShown: 5552-5EWThe modularity of this type of connection point allows the maximum flexibility, customization and future-proofing in a home. Changing plates or jacksMultimedia wallplatesOur home theater solutions make it easy to surround yourself with sound, simplify home theater connections and provide simple, clean ways to manage cable installations for home electronics. Cable management plates come in a variety of confi gurations, can accommodate all cable run needs and can even provide surge protected power.PSECTIONc multimedia wallplate solutions for today’s needsShown: 35M2SManage cables and provide power-choosewallplates that integrate receptacles or surge protection receptacles with replacement surge modules for protection of electronics.Shown: 35M1A recessed, low-profile reverse nose design provides attractive, neat and clean installation, eliminating unsightly wires and plug heads while allowing mounting in either direction.Connectivity point familiesConnectivity pointsIn today’s homes, service connection points are nearly as important as media distribution itself.Finish off service connection points with wallplates that give you the fl exibility and style you need. Decorator inserts upgrade connection points to a designer look, come in a variety of confi gurations and are compatible with any decorator wallplate.Decorator inserts with connectorsStandard size wallplates with connectorsMid-sizewallplates with connectorsPSECTIONOne-piece design and construction reduces time on the job, plus there are fewer parts to keep track of and less waste. Available in many common service needsShown: 3521-4Connectivity points offer contractors solutions at economical price points that most building and remodeling jobs require, yet feature the quality Shown: 3562Options to match common wallplatesOur connectivity point wallplates and inserts matchstandard wallplate sizes and styles to coordinate perfectly with any new or existing installation.。
Turck IM12-22EX-R 2-通道隔离切换放大器说明书
T 22:00:15+02:00The 2-channel isolating switching amplifier IM12-22EX-R is equipped with intrinsically safe input circuits.Sensors according to EN 60947-5-6 (NAMUR)or potential-free contact transmitters can be connected to the device.The output circuits feature 2 relays, each with 1 NO contact.You can toggle between working or closed current, resp. NO or NC mode via three switches at the front. The switching state of channel 1 is thereby transmitted to the outputs 1 and 2.The Pwr LED lights green to indicate opera-tional readiness. LED 1 lights yellow to indi-cate the switching status of the output.■ATEX, IECEx, UL, FM , CSA, TR CU,NEPSI, KOSHA, TIIS, CCOE, INMETRO■Installation in zone 2■ 2 relay outputs (NO)■Output mode adjustable (NO/NC mode)■Multiplexing of signals possible ■Complete galvanic isolationT 22:00:15+02:00Type code IM12-22EX-R Ident no.7541233Nominal voltage Universal voltage supply unit Operating voltage 20…250 VAC Frequency40…70 Hz Operating voltage range 20…125 VDC Power consumption ð 3 WInput 2-channel or 1-channel with signal doubling NAMUREN-60947-5-6No-load voltage 8.2 VDC Short-circuit current 8.2 mA Input resistance 1 k òCable resistance ð 50 òSwitch-on threshold 1.55 mA Switch-off threshold1.75 mAOutput circuits (digital) 2 x relays (NO)Relay switching voltage ð 250 VAC/30 VDC Switching current per output ð 2 ASwitching capacity per output ð 500 VA/60 W Switching frequency ð 10 Hz Contact quality AgNi, 3µ AuGalvanic isolation Test voltage 2.5 kVImportant noteFor safety applications the values specified in the safety manual or the relevant Ex certificates (ATEX,IECEx, UL, etc.) apply.Ex approval acc. to conformity certificate TÜV 04 ATEX 2553Application areaII (1) G, II (1) Dignition protection category [Ex ia Ga] IIC; [Ex ia Da] IIIC Max. values:Terminal connection: 1+4 / 2+5Max. output voltage U ð 9.6 V Max. output current I ð 11 mA Max. output power P ð 26 mW CharacteristiclinearInternal inductance/capacitance L /C Li = 65 µH, Ci negligibly small External inductance/capacitance L /C Ex ia IICIIB Lo [mH]151021020Co [µF]1,10,830,745,23,83,4Ex approval acc. to conformity certificate TÜV 06 ATEX 552968 X Application area II 3 GProtection type Ex nA nC [ic Gc] IIC/IIB T4 Gc Max. values:Terminal connection: 1+4 / 2+5Max.output voltage U ð 9.6 V Max. output current I ð 11 mA Max. output power P ð 26 mW CharacteristiclinearInternal inductance/capacitance L /C Li = 65 µH, Ci negligibly small External inductance/capacitance L /CEx icIICIIBLo [mH]15101510Co [µF]1.91.41.2117.5 6.6IndicationDimensionsOutput relay – Load curveOutput relay – Electrical lifetimeT 22:00:15+02:00Mechanical Data IP RatingIP20Flammability class acc. to UL 94V-0Ambient temperature -25 …+70 °C-25 ... +60 °C für UL, FM, TIIS Storage temperature -40…+80°C Relative humidity ð 95 %Dimensions 104 x 18 x 110 mm Weight148 gMounting instruction for DIN rail / panel Housing material polycarbonate/ABSElectrical connection 4 x 3-pin removable terminal blocks, reverse polarity protected, screw connection Terminal cross-section 1 x 2.5 mm / 2 x 1.5 mm Tightening torque0.5 NmT 22:00:15+02:00AccessoriesType codeIdent no.DescriptionDesignIM-CC-3X2BU/2BK6900475Cage clamp terminals for IM modules (Ex-devices with 18mm overall width); includes: 2 pcs. 3-pin blue terminals and 2pcs. 3-pin black terminals.。
TURCK图尔克传感器产品介绍大全
TURCK图尔克传感器产品介绍大全————————————————————————————————作者：————————————————————————————————日期：TURCK图尔克传感器产品介绍大全————图尔克绝对优势型号超全用于液压缸的直线位移位置类传感器新型磁致伸缩式LTX系列直线位移位置传感器的诞生，标志着图尔克承诺优化液压缸位置检测承诺的兑现。
可以通过选用浮漂型定位磁块实现液位检测.依赖于该传感器的高抗震性和抗冲击的特性，这一系列的传感器也可以应用在建筑机械和其他工作环境较为恶劣的现场。
这一系列产品完善了电感式直线位移传感器家族，特别是某些必须使用磁性定位块的场合.LTX-系列产品符合IP68的防护等级同时它对很多化学品和油污具有抗腐蚀的特性.高品质的不锈钢材质外壳保护了该产品在很多具有腐蚀性的环境正常工作。
LTX系列直线位移位置传感器使用无磨损的检测方式,这保证了它可以提供精确地信号输出，同时具有较高的线性度和重复精度。
它可以提供模拟量信号输出（4-20毫安或0—10伏直流信号）或者是具有高精度的SSI数字信号输出。
一个三色的LED指示灯可以显示出该传感器的工作状态信息。
低输入功率（1瓦）型的产品可以直接连接到显示模块、控制模块或接口模块中.LTX系列传感器简便的编程方式可以轻松的调整检测量程范围。
对于设定较小的测量范围,该产品可以再转瞬之间设置完成。
因此,具有良好通用性的这一系列传感器可以有效的减小不同传感器产品在使用过程中的库存压力.图尔克中文产品数据库正式上线！伴随新版图尔克中文网站www。
的正式上线，专为您配备的全系列中文产品数据库亦同时应运而生.图尔克强大的中文产品数据库拥有15000种自动化产品和系统组件信息，能够极大地节省您的查询时间，帮助您最快速、便捷地了解所需产品信息。
登陆新版的图尔克中文网站，点击导航栏中的“产品中心”栏目，您即可与拥有15000种全系列产品的强大中文产品数据库时实对接。
图尔克安全栅(IM系列)
IM系列隔离栅模块化接口技术Sense it! Connect it! Bus it! Solve it!PC0709-01公 司 简 介TURCK·图尔克TURCK（图尔克）是全球著名的自动化品牌，旗下囊括近15000种丰富多样的传感器产品、工业现场总线产品、过程自动化产品和各类接口及接插件产品，为工厂自动化及过程自动化提供了高效率和系统化的全方位解决方案。
目前，总部位于德国的图尔克集团已在世界27个国家建立分公司、拥有超过2800名雇员，并通过代理与另外60个国家建立商业往来，年营业额近4亿欧元。
TURCK（图尔克）作为工业自动化领军企业已有40多年的历史。
凭借世界一流的设计、生产技术、全系列的产品线、优异的质量和遍布全球的销售服务网络，TURCK不仅能为用户提供及时专业的技术支持与定制产品，还能确保直接在现场为世界各地的客户提供优质的系统化解决方案。
秉承“信任、专业、忠诚、成功”的企业理念，TURCK（图尔克）总是力求为不同用户提供最切合需要的优质产品与服务，通过为客户增值而致力于客户的成功发展。
TURCK（图尔克）产品已广泛应用于世界各国的不同行业，包括汽车制造、电力、食品饮料、石油化工、冶金、烟草、航空航天、机械、纺织、造纸、印刷、包装、轨道交通、物流、水泥建材、造船、电线及电缆制造、采矿、市政等行业，成为深受用户信赖的首选品牌。
图尔克·中国1994年图尔克集团正式在中国投资设立分公司，以便最大化地满足中国市场的需求，并为本地客户提供零距离的定制化服务。
同年9月8日，图尔克（天津）传感器有限公司作为德国图尔克集团的全资子公司，在天津经济技术开发区注册成立。
历经15年的稳健发展，集生产、销售、系统集成、工程服务为一体的图尔克中国公司，已逐步发展成为图尔克集团在亚太地区的生产及销售中心。
目前，图尔克中国公司包括从事销售及市场营销的图尔克（天津）传感器有限公司、从事产品设计生产的图尔克（天津）科技有限公司、以及从事自控系统集成的图尔克（天津）自动化系统有限公司三家下属公司。