CCNA2 Final Exam备课讲稿
CCNA02-final3
1Which of the following are required when adding a network to the OSPF routing process conf iguration? (Choose three.)network addressloopback addressautonomous system numbersubnet maskwildcard maskarea ID2Using default settings, what is the next step in the router boot sequence after t he IOS loads from flash?Perf orm the POST routine.Search for a backup IOS in ROM.Load the bootstrap program f rom ROM.Load the running-config file from RAM.Locate and load the startup-config file from NVRAM.3Refer to the exhibit. What is the most efficient summarization of the routes attached to router R1?198.18.0.0/16198.18.48.0/21198.18.32.0/22198.18.48.0/23198.18.49.0/23198.18.52.0/224Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statem (Choose three.)The missing information f or Blank 1 is the command show ip route .The missing information f or Blank 1 is the command debug ip route .The missing information f or Blank 2 is the number 100.The missing information f or Blank 2 is the number 120.The missing information f or Blank 3 is the letter R.The missing information f or Blank 3 is the letter C.5Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose t wo.)10.0.0.0/864.100.0.0/16128.107.0.0/16172.16.40.0/24192.168.1.0/24192.168.2.0/246When presented with multiple valid routes to a destination, what criteria does a router use to determine which routes to add to the routing table?The router selects the routes with the best metric. All routes that hav e the same best metric are added to the routing table.The router f irst selects routes with the lowest administrative distance. The resulting routes are then prioritized by metric and the routes with the best metric arouting table.The router selects the routes with the lowest administrativ e distance. All routes with the same lowest administrative distanc e are added to the routing table.The router installs all routes in the routing table but uses the route with the best metric most when load balancing.7Refer to the exhibit. All routers in the network are running RIPv2 and EIGRP with default routing protocol settings and have interfaces configured with the bandwidths t exhibit. Which protocol will be used and how will traffic between the Router1 LAN and Router5 LAN be routed through the network?RIPv2 will load balance across both paths between Router1 and Router5.EIGRP will load balance across both paths between Router1 and Router5.RIPv2 traffic will use the path Router1, Router2, Router5 because it has the least hops.EIGRP traffic will use the path Router1, Router3, Router4, Router5 because it has the best metric.8Of the listed routing protocols, which two will propogate LSPs to all neighbors? (Choose two.)IS-ISEIGRPOSPFRIPv1RIPv29Refer to the exhibit. Routers 1 and 2 are directly connected over a serial link. Pings are f ailing between the two routers. W hat change by the administrator will correctSet the encapsulation on both routers to PPP.Decrease the bandwidth on Serial 0/1/0 on router 2 to 1544.Change the cable that connects the routers to a crossover cable.Change the IP address on Serial 0/1/0 on router 2 to 192.168.0.1/30.10Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.)The route to network 172.16.0.0 has an AD of 156160.Network 192.168.0.16 can best be reached using FastEthernet0/0.The AD of EIGRP routes has been manually changed to a value other than the default value.Router1 is running both the EIGRP and OSPF routing process.Network 172.17.0.0 can only be reached using a default route.No default route has been conf igured.11Which statement correctly describes a feasible successor in EIGRP?It is a primary route that is stored in the routing table.It is a backup route that is stored in the routing table.It is a primary route that is stored in the topology table.It is a backup route that is stored in the topology table.12Refer to the exhibit. A ping from R1 to 10.1.1.2 is successful, but a ping from R1 to 192.168.2.0 fails. What is the cause of this problem?There is no gateway of last resort at R1.The serial interf ace between the two routers is down.A default route is not configured on R1.The static route for 192.168.2.0 is incorrectly conf igured.13Refer to the exhibit. A network administrator has run the show interface command. The output of this command is displayed. What is the first step that is required toSwitch the cable with a known working cable.Issue the no shutdown command on the interface.Configure the interf ace as a loopback interface.Set the encapsulation for the interface.14Which two locations can be the source of the Cisco IOS that is used by a router during the bootup process? (Choose two.)flash memoryRAMNVRAMTFTP serverconfiguration register15All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondrouters use to determine the router ID?The highest MAC address among the active interfaces of the network will be used.There will be no router ID until a loopback interf ace is configured.The highest IP address among the activ e FastEthernet interfaces that are running OSPF will be used.The highest IP address among the activ e interfaces will be used.16Refer to the exhibit. A network administrator has conf igured OSPF using the following command:network 192.168.1.32 0.0.0.31 area 0Which router interf ace will participate in OSPF?FastEthernet0/0FastEthernet0/1Serial0/0/0Serial0/0/117Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is f ully converged. A host on th with a host on the 192.168.2.0/24 network.Which path will be used to transmit the data?The data will be transmitted v ia R3-R2.The data will be transmitted v ia R3-R1-R2.The traffic will be load-balanced between two paths — one via R3-R2, and the other via R3-R1-R2.The data will be transmitted v ia R3-R2, and the other path via R3-R1-R2 will be retained as the backup path.18Which two situations require the use of a link-state protocol? (Choose two.)Fast convergence of the network is critical.The network is very large.The network administrator has limited knowledge to configure and troubleshoot routing protocols.The network is a flat network.The capacity of the router is low.19Refer to the exhibit. What is the meaning of the highlighted value 120?It is the metric that is calculated by the routing protocol.It is the v alue that is used by the DUAL algorithm to determine the bandwidth for the link.It is the administrative distance of the routing protocol.It is the hold-down time, measured in seconds, before the next update.20In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this nD 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/021Which statement is true about the RIPv1 protocol?It is a link-state routing protocol.It excludes subnet information from the routing updates.It uses the DUAL algorithm to insert backup routes into the topology table.It uses classless routing as the default method on the router.22Refer to the exhibit. The 10.4.0.0 network f ails. What mechanism prevents R2 f rom receiving false update information regarding the 10.4.0.0 network?split horizonhold-down timersroute poisoningtriggered updates23Which statement is true about the metrics used by routing protocols?A metric is a value used by a particular routing protocol to compare paths to remote networks.A common metric is used by all routing protocols.The metric with the highest value is installed in the routing table.The router may use only one parameter at a time to calculate the metric.24Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undef ined. R1 can ping 192.168.2.1 and 10.1.1.2, but is unable to ping 192.16 What is the reason for the ping f ailure?The serial interf ace between two routers is down.R2 is not forwarding the routing updates.The 192.168.4.0 network is not included in the RIP configuration of R2.RIPv1 needs to be configured.25Which statement correctly describes a feature of RIP?RIP is a link-state routing protocol.RIP uses only one metric—hop count— for path selection.Adv ertised routes with hop counts greater than 10 are unreachable.Messages are broadcast every 10 seconds.26Refer to the exhibit. When the show cdp neighbors command is issued f rom router C, which devices will be displayed in the output?B, DA, B, DD, SWH-2SWH-1, A, BSWH-1, SWH-2A, B, D, SWH-1, SWH-227Refer to the exhibit. Although R2 is conf igured correctly, host A is unable to access the Internet. What are two static routes that can be c onfigured on R1, either of which w (Choose two.)ip route 0.0.0.0 0.0.0.0 Fa0/0ip route 0.0.0.0 0.0.0.0 Fa0/1ip route 0.0.0.0 0.0.0.0 10.1.1.1ip route 0.0.0.0 0.0.0.0 10.1.1.2ip route 209.165.202.0 255.255.255.0 10.1.1.128Which component is typically used to connect the WIC interface of a router to a CSU/DSU?V.35 cableRJ-45 adaptercrossover cablestraight-through cable29Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interf ace of Router2 in order to put the interf ace in the same networ interface of Router1?IP 172.16.0.18, subnet mask 255.255.255.0IP 172.16.32.15, subnet mask 255.255.255.240IP 172.16.0.18, subnet mask 255.255.255.252IP 172.16.32.18, subnet mask 255.255.255.25230Refer to the exhibit. Which host has a combination of IP address and subnet mask on the same network as Fa0/0 of Router1?host Ahost Bhost Chost D31Refer to the exhibit. OSPF is used f or the routing protocol and all interf aces are configured with the correct IP addresses and subnet masks. During testing, it is foun unable to form an adjacency with R2. What is the cause of this problem?Both routers have been configured with incorrect router IDs.Both routers have been configured in different OSPF areas.Both routers have been configured with an incorrect network type.Both routers have been configured with different hello and dead intervals.32You hav e been asked to explain converged networks to a trainee. How would you accurately describe a converged network?A network is converged when all routers have f ormed an adjacency.A network is converged immediately after a topology change has occurred.A network is converged when all routers flush the unreachable networks from their routing tables.A network is converged after all routers share the same information, calculate best paths, and update their routing tables.33 A network administrator is in charge of two separate networks that share a single building. What dev ice will be required to connect the two networks and add a comthe Internet that can be shared?hubrouteraccess pointEthernet switch34Which port should a terminal emulator be connected to in order to access a router without network connectivity?T1serialconsoleFastEthernet35Refer to the exhibit. What needs to be done to allow these two routers to connect successf ully?Add a clock rate to S0/0/0 on R1.Add an interface description to S0/0/1 on R2.Change the serial interface on R2 to S0/0/0 so that it matches R1.Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1.36Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?The login command was not entered on the console line.The enable password should be an enable secret password.No username and password combination has been configured.Console connections cannot be conf igured to require users to provide passwords.37Refer to the exhibit. When a static IP address is being configured on the host, what address should be used for the default gateway?10.1.1.110.1.1.2172.16.1.1192.168.1.138Refer to the exhibit. The entire 192.168.1.0 network has been allocated to address hosts in the diagram. Utilizing VLSM with contiguous address blocks, which set of pref ixes could be used to create an addressing solution with a minimum waste of IP addresses?39What is a function of a router?It extends the Layer 2 broadcast domain.It eliminates collisions among PCs on the same local network.It provides connectivity among PCs on the same physical segment.It forwards packets to different IP networks based on Layer 3 inf ormation.40Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding traffic between BR and HQ?RIPRIPv2EIGRPstatic routes41Refer to the exhibit. A network administrator configures a static route on router R1 to reach the 192.168.1.0/24 network. Which IP address should be used as the next ip route command?192.168.1.1192.168.2.1192.135.250.1192.135.250.242Refer to the exhibit. The network is conf igured with RIPv2. However, network administrators notice that communication cannot be successfully completed f rom one L network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem?Disable the load balancing feature of RIPv2.Issue the no auto-summary command for RIPv2.Replace RIPv2 with EIGRP which supports VLSM.Make sure that the network statements include the correct subnet mask.43Which protocol is used by EIGRP to deliver and receive update packets?FTPRTPTCPTFTPUDP44Refer to the exhibit. What OSPF network statements are required for the router B to adv ertise the three networks that are attached?router ospf 1network 10.0.0.0 0.0.0.255 area 0router ospf 1network 10.1.1.0 0.3.255.255 area 0network 10.10.1.0 0.255.255.255 area 0network 10.20.1.0 0.255.255.255 area 0router ospf 1network 10.1.1.0 0.0.0.3 area 0network 10.10.1.0 0.0.255.255 area 0network 10.20.1.0 0.0.255.255 area 0router ospf 1network 10.1.1.0 0.0.0.3 area 0network 10.10.1.0 0.0.0.255 area 0network 10.20.1.0 0.0.0.255 area 045Which two v alues are used by default to calculate a metric in EIGRP? (Choose two.) loaddelayreliabilityhop countbandwidth46Refer to the exhibit. Which statement is true concerning the routing configuration?Using dy namic routing instead of static routing would hav e required f ewer configuration steps.The 10.1.1.0/24 and 10.1.2.0/24 routes have adjacent boundaries and should be summarized.Packets routed to the R2 Fast Ethernet interface require two routing table lookups.The static route will not work correctly.47Refer to the exhibit. On the basis of the show running-config output, which option correctly ref lects the routes that will be listed in the R2 routing table?48Refer to the exhibit. Which command should be issued to configure the address of the router interface that is attached to this computer?Router(config-if)# ip address 192.168.2.1 255.255.255.0Router(config-if)# ip address 192.168.2.2 255.255.255.0Router(config-if)# ip address 192.168.0.1 255.255.255.0Router(config-if)# ip address 192.168.0.2 255.255.255.049Refer to the exhibit. Which route will be removed from the routing table if manual EIGRP summarization is disabled on the Serial0/0/0 interface of Router3?0.0.0.0/0172.16.0.0/16172.16.1.0/24172.16.3.0/3050Refer to the exhibit. All interfaces are addressed and f unctioning correctly. The network administrator runs the tracert command on host A. Which two f acts could be output of this command? (Choose two.)The gateway for Host A is missing or improperly conf igured.The gateway for Host B is missing or improperly conf igured.The entry for 192.168.1.0/24 is missing f rom the routing table of R1.The entry for 192.168.1.0/24 is missing f rom the routing table of R2.The entry for 192.168.2.0/24 is missing f rom the routing table of R1.The entry for 192.168.2.0/24 is missing f rom the routing table of R2.。
CCNA2-FINAL-(A+B+C套)英文版
CCNA第二学期《Final Examinnation》英文A卷1 What are two functions of a router? (Choose two.)It forwards data packets toward their destination.It forwards the packet to the destination if the TTL value is 0.It changes the destination IP address of data packets before forwarding them to an exit interface.It determines the best path based on the destination MAC address.It acts as an intersection between multiple IP networks.2 Which router component contains a scaled-down version of the IOS that can be used to reload a complete version of the IOS in the event that the IOS becomes damaged or corrupted?ROMFlashSDRAMNVRAM3 Using default settings, what is the next step in the router boot sequence after the IOS loads from flash? Perform the POST routine.Search for a backup IOS in ROM.Load the bootstrap program from ROM.Load the running-config file from RAM.Locate and load the startup-config file from NVRAM.4Refer to the exhibit. How many routes are ultimate routes?34575ADCABCIt will load balance the traffic between ADC and ABCIt will send the traffic via ABC, and will use ADC as a backup path only when ABC fails.6Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols.Which path will be used to transmit the data packets from PC1 to PC2?The packets will travel via R2-R1.The packets will travel via R2-R3.The traffic will be load-balanced between two paths — via R2-R1 and via R2-R3.The packets will travel via R2-R3, and the other path via R2-R1 will be retained as the backup path.Refer to the exhibit. The network is configured for OSPF routing with default settings. The bandwidths have been configured correctly for each link. If the T1 link between router A and router E fails, what path will a packet from router A take to reach the LAN attached to router F when the network has converged?A, B, C, FA, B, C, E, FA, D, G, E, FA, D, G, H, F8 In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/09 Which two statements are true for link-state routing protocols? (Choose two.)Routers that run a link-state protocol can establish a complete topology of the network.Routers in a multipoint network that run a link-state protocol can exchange routing tables.Routers use only hop count for routing decisions.The shortest path first algorithm is used.Split horizon is used to avoid routing loops.10with static routeswith a routed protocolwith a routing protocolwith directly connected routes11Refer to the exhibit. What is the meaning of the highlighted value 120?It is the metric that is calculated by the routing protocol.It is the value that is used by the DUAL algorithm to determine the bandwidth for the link.It is the administrative distance of the routing protocol.It is the hold-down time, measured in seconds, before the next update.12 Which statement is true about the metrics used by routing protocols?A metric is a value used by a particular routing protocol to compare paths to remote networks.A common metric is used by all routing protocols.The metric with the highest value is installed in the routing table.The router may use only one parameter at a time to calculate the metric.13 Which routing protocol by default uses bandwidth and delay to calculate the metric of a route? RIPv1RIPv2OSPFEIGRP14 Which three routing metrics are correctly defined? (Choose three.)delay - the link speedreliability - the error rate on a linkload - the amount of traffic on a linkcost - the value to indicate preference for a routehop count - the path selected with the highest bandwidthbandwidth - the amount of time it takes a packet to travel a link15 Which two statements about routing protocols are accurate? (Choose two.)OSPF supports VLSM.RIPv1 supports VLSM.RIPv2 does not have a hop count limit.EIGRP supports discontiguous network designs.16Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which two devices can be used for this? (Choose two.)a CSU/DSU devicea modeman Ethernet switcha huba bridge17 When connecting two devices, which situation would normally require the use of a crossover cable? connecting a host to a switchconnecting a switch to a routerconnecting a switch to a switchconnecting a host to a router console port18Refer to the exhibit. A network administrator has run the show interface command. The output of this command is displayed. What is the first step that is required to make this interface operational?Switch the cable with a known working cable.Issue the no shutdown command on the interface.Configure the interface as a loopback interface.Set the encapsulation for the interface.19 Which port should a terminal emulator be connected to in order to access a router without network connectivity?T1serialconsoleFastEthernet20 Which router mode is accessed by entering the enable command?user EXECprivileged EXECglobal configurationinterface configuration21Refer to the exhibit. When a static IP address is being configured on the host, what address should be used for the default gateway?10.1.1.110.1.1.2172.16.1.122Refer to the exhibit. The show cdp neighbors command was run on one of the devices as shown. Based on this information, which two facts can be determined? (Choose two.)The command was run on the router.ABCD is a non- CISCO device.Layer 3 connectivity between two devices exists.ABCD supports routing capability.ABCD is connected to the Fa0/0 interface of the neighboring device.23Refer to the exhibit. Which statement is true about the Ethernet interfaces shown in the network?A frame leaves interface Fa0/0 of R1 with the source MAC address as 000C.3010.9260.A packet will not be forwarded between R1 and R2 until the no shutdown command is issued on the Fa0/0 interface of R1.24Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding traffic between BR and HQ?RIPRIPv2EIGRPstatic routes25Refer to the exhibit. Pings are failing between HostA and HostB. The network administrator discovers that Router1 does not have a route to the 172.16.0.0 network. Assuming Router2 is configured correctly, which two static routes could be configured on Router1 to enable Host A to reach network 172.16.0.0? (Choose two.)ip route 172.16.0.0 255.255.0.0 S0/0ip route 172.16.0.0 255.255.0.0 S0/1ip route 172.16.0.0 255.255.0.0 192.168.0.1ip route 192.168.0.1 172.16.0.0 255.255.0.0 S0/0ip route 192.168.0.1 172.16.0.0 255.255.0.0 S0/126Refer to the exhibit. How was the OSPF default gateway entry for R2 determined?Default routes are automatically injected by OSPF into all advertisements.A static default gateway route is defined in the configuration of R2.The default-information originate command is applied on R1.The ISP defines the gateway of last resort and automatically passes it to R1 and R2.The ip default-gateway command is applied on R2.27Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be listed in the R2 routing table?答案：D28192.168.2.1192.135.250.129 Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a static route entry be altered to accommodate a topology change?Keep the existing static route and configure a new static route with the correct next hop IP address.Negate the existing static route and configure a new static route with the correct next hop IP address.Do nothing. The existing static route will automatically update the next hop entry with the new IP address. Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP address.30Refer to the exhibit. The entire 192.168.1.0 network has been allocated to address hosts in the diagram. Utilizing VLSM with contiguous address blocks, which set of addresses and prefixes could be used to create an addressing solution with a minimum waste of IP addresses?答案：D31Refer to the exhibit. Which host has a combination of IP address and subnet mask on the same network as Fa0/0 of Router1?host Ahost Bhost Chost D32Refer to the exhibit. If the EIGRP routing protocol is used throughout the network, which IP address and mask prefix should be sent by router R1 to the Edge router as a result of manual summarization of LANs A, B, C, and D?33Refer to the exhibit. Routers RTRA and RTRB are running OSPF. What entry does RTRA add in the routing table when Serial 0/0/0 receives an update about the network that is attached to RTRB?O 172.16.7.0/30 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0O 172.16.7.16/28 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0O 172.16.7.0/24 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0O 172.16.0.0/16 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/034Refer to the exhibit. If RIPv1 is used as the routing protocol throughout the network, what RIPv1 route will router R1 advertise to router R3?10.1.0.010.1.1.010.1.2.035 Which statement correctly describes a feature of RIP?RIP is a link-state routing protocol.RIP uses only one metric—hop count— for path selection.Advertised routes with hop counts greater than 10 are unreachable.Messages are broadcast every 10 seconds.36Refer to the exhibit. The network is using the RIPv2 routing protocol. If network 10.0.0.0 goes down, what mechanism will prevent Router1 from advertising false routing information back to Router2?triggered updatespoison reverseholddown timerssplit horizonroute poisoningsplit horizonhold-down timertriggered updates38Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)The missing information for Blank 1 is the command show ip route.The missing information for Blank 1 is the command debug ip route.The missing information for Blank 2 is the number 100.The missing information for Blank 2 is the number 120.The missing information for Blank 3 is the letter R.The missing information for Blank 3 is the letter C.39Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly configured and operational. Both routers are configured to include all connected interfaces in routing updates. R2 is not showing any routes from R1 in the routing table. What is the likely cause?The adjacent interfaces are passive.The distance of 120 exceeds 15 hops.R2 will not accept version 1 updates from R1.Routes are being summarized by R1 but not by R2.40Refer to the exhibit. All routers are configured to use the EIGRP routing protocol with defaultIt will travel via A, B, and C.It will travel via A, F, E, D, and C.It will travel via A, G, H, and C.41 Which multicast address does EIGRP use to send hello and updates packets?224.0.0.5224.0.0.6224.0.0.942 A router has EIGRP configured as the only routing protocol. In what way might EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?It broadcasts hello packets to all routers in the network to re-establish neighbor adjacencies.It sends queries to adjacent neighbors until a new successor route is found.It immediately sends its entire routing table to its neighbors.It will set the metric for the failed route to infinity.43Refer to the exhibit. EIGRP 1 has been configured on R1. What is the effect of configuring the ip bandwidth-percent eigrp command?The EIGRP bandwidth routing metric will be reduced by 30%.EIGRP 1 protocol traffic will be restricted to 30% of the link bandwidth.Packets that are routed based on EIGRP routing table entries will be limited to 30% of the link bandwidth. EIGRP traffic will be permitted to burst for short periods to 30% above the configured link bandwidth.44Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)All routes are stable.Each route has one feasible successor.The administrative distance of EIGRP has been set to 50.The show ip eigrp topology command has been run on R1.45Refer to the exhibit. A network designer is testing a prototype of WAN connections. All of the routers in the exhibit are configured for OSPF routing. The design requires that the path between routers A and D through ISP-A is the primary and the path through ISP-B servers as a backup. The designer notices that router A has two equal-cost paths to the LAN on router D. How can the designer correct this problem?Issue a clock rate 2000000 interface command on S0/0/1 of router ISP-B.Change the default OSPF reference bandwidth on router A.Configure two static routes with administrative distances of 10.Use the bandwidth command to change the default bandwidth on the link to router B.46Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What two configuration changes will correct the problem? (Choose two.)Set a lower priority on R2.Configure the routers in the same area.Set a lower cost on R2 compared to R1.Add a backup designated router to the network.Match the hello and dead timers on both routers.47Refer to the exhibit. If the router loopback interfaces, FastEthernet interfaces, and OSPF priorities are configured as shown, which router would win an OSPF DR election?ABCD48 Two routers need to be configured within a single OSPF area. Which two components need to be configured on both routers to achieve this? (Choose two.)the same process IDthe same area IDnetwork addresses and wildcard masksthe same router IDthe same loop back address49Refer to the exhibit. What OSPF network statements are required for the router B to advertise the three networks that are attached?router ospf 1network 10.0.0.0 0.0.0.255 area 0router ospf 1network 10.1.1.0 0.3.255.255 area 0network 10.10.1.0 0.255.255.255 area 0network 10.20.1.0 0.255.255.255 area 0router ospf 1network 10.1.1.0 0.0.0.3 area 0network 10.10.1.0 0.0.255.255 area 0network 10.20.1.0 0.0.255.255 area 0router ospf 1network 10.1.1.0 0.0.0.3 area 0network 10.10.1.0 0.0.0.255 area 0network 10.20.1.0 0.0.0.255 area 050Refer to the exhibit. A network administrator is trying to determine why router JAX has no OSPF routes in its routing table. All routers are configured for OSPF area 0. From the JAX router, the administrator is able to ping its connected interfaces and the Fa0/1 interface of the ORL router but no other router interfaces. What is a logical step that the network administrator should take to troubleshoot the problem?Reboot the routers.Change the OSPF process ID on all of the routers to 0.Check to see if the cable is loose between ORL and JAX.Check to see if CDP packets are passing between the routers.Use show and debug commands to determine if hellos are propagating.CCNA第二学期《Final Examinnation》英文B卷1 A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared?hubrouteraccess pointEthernet switch2 Which two router component and operation pair are correctly described? (Choose two.)DRAM - loads the bootstrapRAM - stores the operating systemFlash - executes diagnostics at bootupNVRAM - stores the configuration fileROM - stores the backup configuration filePOST - runs diagnostics on hardware modules3 A router boots and enters setup mode. What is the reason for this?The IOS image is corrupt.Cisco IOS is missing from flash memory.The configuration file is missing from NVRAM.The POST process has detected hardware failure.4Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)5 Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?6Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols.Which path will be used to transmit the data packets from PC1 to PC2?The packets will travel via R2-R1.The packets will travel via R2-R3.The traffic will be load-balanced between two paths — via R2-R1 and via R2-R3.The packets will travel via R2-R3, and the other path via R2-R1 will be retained as the backup path.R 192.168.1.0/24 [120/3] via 192.168.110.1, 00:00:17, Serial0/1/0R 192.168.1.0/24 [120/2] via 192.168.200.1, 00:00:17, Serial0/0/0R 192.168.1.0/24 [120/1] via 192.168.100.1, 00:00:17, Serial0/0/1R 192.168.1.0/24 [120/4] via 192.168.101.1, 00:00:17, Serial0/1/18Refer to the exhibit. The router receives a packet that is destined for 192.168.5.79. How will the router handle this packet?It will forward the packet via the FastEthernet0/0 interface.It will forward the packet via the Serial0/0/0 interface.It will forward the packet via the Serial0/0/1 interface.It will drop the packet.9 A network administrator uses the RIP routing protocol to implement routing within an autonomous system. What are two characteristics of this protocol? (Choose two.)It uses the Bellman-Ford algorithm to determine the best path.It displays an actual map of the network topology.It offers rapid convergence in large networks.It periodically sends complete routing tables to all connected devices.It is beneficial in complex and hierarchically designed networks.10 Which two statements are true for link-state routing protocols? (Choose two.)Routers that run a link-state protocol can establish a complete topology of the network.Routers in a multipoint network that run a link-state protocol can exchange routing tables.Routers use only hop count for routing decisions.The shortest path first algorithm is used.Split horizon is used to avoid routing loops.11 Which two statements are true about classless routing protocols? (Choose two.)They can be used for discontiguous subnets.They can forward supernet routes in routing updates.They cannot implement classful routes in routing tables.They use only a hop count metric.They do not include the subnet mask in routing updates.12 Which statement is true regarding routing metrics?All routing protocols use the same metrics.EIGRP uses bandwidth as its only metric.Routers compare metrics to determine the best route.The larger metric generally represents the better path.13 Which routing protocol by default uses bandwidth and delay to calculate the metric of a route?RIPv2OSPFEIGRP14 You have been asked to explain converged networks to a trainee. How would you accurately describe a converged network?A network is converged when all routers have formed an adjacency.A network is converged immediately after a topology change has occurred.A network is converged when all routers flush the unreachable networks from their routing tables.A network is converged after all routers share the same information, calculate best paths, and update their routing tables.15Refer to the exhibit. All the routers are properly configured to use the RIP routing protocol with default settings, and the network is fully converged. Router A is forwarding data to router E. Which statement is true about the routing path?Router A will send the data via the A-D-E path that is listed in the routing table.Router A will load-balance the traffic between A-B-E and A-C-E.Router A will determine that all paths have equal metric cost.Router A will send the data through A-D-E and keep A-B-E and A-C-E as the backup paths.16Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which two devices can be used for this? (Choose two.)a CSU/DSU devicean Ethernet switcha huba bridge17 Which component is typically used to connect the WIC interface of a router to a CSU/DSU?V.35 cableRJ-45 adaptercrossover cablestraight-through cable18 Which router mode is accessed by entering the enable command?user EXECprivileged EXECglobal configurationinterface configuration19Refer to the exhibit. What are the effects of the exhibited commands on the router?All passwords are encrypted.Only Telnet sessions are encrypted.Only the enable password is encrypted.Only the enable password and Telnet session are encrypted.Enable and console passwords are encrypted.20Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that interface FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1?A clock rate should be added to the interface configuration.The subnet mask should be added to the interface configuration.An interface description needs to be added to the interface configuration.The no shutdown command needs to be added to the interface configuration.21Refer to the exhibit. Which two facts can be derived from this output? (Choose two.)Three network devices are directly connected to Router2.The serial interface between Router2 and Router3 is up.Router1 and Router3 are directly connected.Six devices are up and running on the network.Layer 3 functionality between routers is configured properly.22Refer to the exhibit. Which route in the routing table of R1 will be discarded by its neighboring router? 192.168.2.0192.168.3.0192.168.9.0192.168.10.0192.168.11.023Refer to the exhibit. All interfaces are addressed and functioning correctly. The network administrator runs the tracert command on host A. Which two facts could be responsible for the output of this command? (Choose two.)The gateway for Host A is missing or improperly configured.The gateway for Host B is missing or improperly configured.24 In which situation would a default static route be recommended?when connecting an edge router to the Internetwhen variable length subnet masking is in effectwhen there is more than one valid route for a destination networkwhen a destination network has a larger mask than any routes in the routing table25 What is the advantage of configuring a static route with an exit interface instead of a next-hop address?The router will perform a recursive lookup.This route will automatically be used as the gateway of last resort.The exit interface configuration consumes less router processing time.The exit interface configuration has an administrative distance value of 1.26Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be listed in the R2 routing table?答案：D27 A static route has been configured on a router. However, the destination network no longer exists. What should an administrator do to remove the static route from the routing table?Change the routing metric for that route.Nothing. The static route will go away on its own.Change the administrative distance for that route.Remove the route using the no ip route command.28Refer to the exhibit. Hosts on the 192.168.1.0 network cannot communicate with hosts on the 172.16.1.1 network. The network administrator has run the show ip route command on R1.What could be the cause of this problem?The FastEthernet interface on R1 is disabled.Autosummarization is enabled on R1.The serial interface S0/0/0 of R1 is administratively down.No static route or routing protocol is configured.29A new static route must be configured on R1 with the R3 serial interface as the next hop.A new default route must be configured on R1 with the R3 serial interface as the next hop.The default route on R2 should be configured with the R3 serial interface as the next hop.The default route on R2 must be replaced with a new static route and the next hop should be the R1 FastEthernet interface.31Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?32Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?The IP address of host A is incorrect.The default gateway of host A is incorrect.The Fa0/1 interfaces of the two routers are configured for different subnets.The subnet mask for the Fa0/0 interface of R1 is incorrect.33Automatic summarization is enabled on R1.The routing table of R2 contains only classful networks.R2 will reject this update.The routing protocol that is configured on both routers is RIPv1.34 Which additional piece of information is included in the updates of classless routing protocols to support the use of VLSM and discontiguous networks?metricnetwork maskneighbor router IDadministrative distance35Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the routers in this topology will respond to this event?Router4 will learn about the failed route 30 seconds later in the next periodic update.Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the holddown timer expires.Router5 immediately flushes the unreachable route from its routing table.Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.clears an unreachable route from the routing table after the invalid timer expiresprevents regular update messages from inappropriately reinstating a route that may have gone badremoves an unreachable route from the routing table after the flush timer expireslimits the period of time or number of hops a packet can traverse through the network before it should be discardedused to mark the route as unreachable in a routing update that is sent to other routers37 Which two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.)authenticationlink-state advertisementshold-down timersSpanning Tree Protocolsplit horizon38Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem?An incorrect IP address is configured between the two routers.No static route is configured on Router2.A routing loop has occurred.No routing protocol is configured on either of the two routers.39。
CCNA第四学期官方章节考试题之第四学期《Final_Examination》(附答案)
公司与AA2SSH存在不正确的访问控制列表条目。
访问列表中的必须在会防止以明文传输登录信息如果身份验证失败，则会断开PPP 会话连接会发起双向握手容易遭受回送攻击4命令show frame-relay map的输出如下：Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active 下列哪三种说法正确描述了所示内容的意义？（选择三项。
）192.168.151.4代表远程路由器的IP 地址192.168.151.4代表本地串行接口的IP 地址DLCI 122代表远程串行接口DLCI 122代表用于连接远程地址的本地编号broadcast表示动态路由协议（例如RIP v1）可通过此PVC 发送数据包active表明ARP 进程正在工作5路由器的SDM 主页会显示哪三点信息？（选择三项。
）ARP 缓存闪存的总容量和可用容量路由表已配置的LAN 接口的数量是否配置了DHCP 服务器该LAN 中路由器的数量6从非军事区分界点本地环路网云确保在确认确保路由器上有通向下列哪三种说法正确描述了CSU/DSU调制解调器用于端接本地数字环路。
CSU/DSU调制解调器用于端接本地模拟环路。
路由器通常被视为路由器通常被视为10在链路质量测试完毕后，路由器在协商第LCPNCP它会被丢弃。
它会被放到队列中，直到主机它会被转换，源端口号保持为它会被分配其端口范围内的第一个可用端口号。
交换虚电路的相关信息将DLCI 映射到网络地址提供流量控制提供错误通知提供拥塞通知发送keepalive 数据包以检验PVC 的工作情况14请参见图示。
下列说法中哪三项正确？（选择三项。
）启用了NAT 过载。
启用了动态NAT。
地址转换会失败。
接口配置不正确。
地址为192.168.1.255 的主机将被转换。
进入0/0/2 接口的流量先被转换，然后才流出串行接口0/0/0。
ccna课程设计报告
ccna课程设计报告一、教学目标本课程的教学目标是使学生掌握CCNA（Cisco Certified Network Associate）的基本知识和技能，能够配置和维护简单的企业网络。
具体目标如下：1.知识目标：学生需要掌握网络基础知识、TCP/IP协议、路由和交换原理、网络设备配置等。
2.技能目标：学生能够使用网络设备进行基本的配置和故障排除，掌握命令行界面和图形用户界面的操作，能够进行简单的网络设计和优化。
3.情感态度价值观目标：培养学生对网络技术的兴趣和热情，提高他们解决实际问题的能力，培养他们的团队合作意识和创新精神。
二、教学内容教学内容将根据课程目标进行选择和，确保内容的科学性和系统性。
具体内容包括：1.网络基础知识：计算机网络的分类、拓扑结构、传输介质等。
2.TCP/IP协议：IP地址、子网划分、路由协议、DNS、DHCP等。
3.路由和交换原理：路由器和工作原理、交换机和工作原理、VLAN、Trunk、Spanning Tree等。
4.网络设备配置：路由器、交换机的命令行操作，配置静态路由、动态路由、访问控制列表等。
5.网络设计和优化：网络设计的原则和方法、网络优化的策略和技术。
三、教学方法为了激发学生的学习兴趣和主动性，将采用多种教学方法，如讲授法、讨论法、案例分析法、实验法等。
1.讲授法：用于讲解网络基本概念和原理，帮助学生建立网络知识体系。
2.讨论法：通过小组讨论，让学生深入理解网络技术的应用和实际问题。
3.案例分析法：分析实际网络案例，培养学生解决实际问题的能力。
4.实验法：让学生动手配置和维护网络设备，提高实际操作能力。
四、教学资源教学资源包括教材、参考书、多媒体资料、实验设备等，将选择和准备适当的教学资源，以支持教学内容和教学方法的实施，丰富学生的学习体验。
1.教材：选用官方推荐的CCNA学习教材，为学生提供全面的知识和技能学习。
2.参考书：提供网络技术方面的经典书籍，供学生深入研究。
final exam 2 CCNA 第三学期(免费下载)
请参见图示。
将图中列出的命令输入路由器R1 和交换机S1 后，PC1 和PC2 彼此无法ping 通。
网络管理员输入show interfaces trunk命令后获得了图中所示的结果。
问题很可能出在哪里？路由器上未配置路由协议。
已建立中继链路，但未将任何VLAN 配置为使用该中继链路。
由于交换机端口未配置为中继，因此未建立中继链路。
必须在交换机或路由器上或同时在这两台设备上配置dynamic desirable选项，动态中继协议才能建立中继链路。
2请参见图示。
哪一个口令可让管理员进入特权执行模式？Bcisco1cisco2cisco3Cisco3下列关于service password-encryption命令的说法中哪项正确？cservice password-encryption命令应在特权执行模式提示符下输入。
service password-encryption命令只加密控制台与VTY 端口的口令。
service password-encryption命令对运行配置中先前未加密的所有口令进行加密。
若要查看通过service password-encryption命令加密的口令，可输入no service password-encryption命令。
4请参见图示。
RTB 被配置为进行传统的VLAN 间路由。
RTB 可以ping 通计算机 A 但无法ping 通计算机B。
此故障的原因可能是什么？Fa0/11 端口处于错误的VLAN 中。
RTB 上没有有效的路由协议。
计算机 B 的IP 地址在错误的逻辑网络中。
路由器的Fa0/1 接口上配置了错误的中继封装类型。
5请参见图示。
最近安装了SW1 用于取代集线器。
主机1 和主机 4 同时传送数据。
网络设备会如何处理此事件？（选择两当冲突发生时，会调用回退算法。
A D由于主机 1 和主机4 都连接到交换机，因此不会发生冲突。
交换机将根据交换机MAC 地址表中的信息将数据转发到相应的端口。
CCNA2PracticeFinalExamAnswerV3.1
CCNA2PracticeFinalExamAnswerV3.11. Which statements are true regarding VTY passwords? (Choose two.)VTY passwords must be encrypted.All VTY lines do not need to use the same password.A VTY password is required to establish telnet sessions.The VTY password is set with the command line console 0.The VTY password must be identical with the enable secret password. 2.Refer to the network and routing table entries shown in the graphic. What will happen when a packet destined for network 192.66.7.0 is received by Router A?It will be forwarded through interface S1.It will be forwarded to the default route.It will be directed toward the Internet.It will be discarded.3.Which command will produce the output shown in the graphic?show cdpshow cdp neighborsshow cdp neighbors detailshow cdp detail4.Router B received an interface configuration change. Suddenly, it transmits a new update. Which of the following could have triggered this update? (Choose two.)Router B received a configuration change.Router A sent a message requesting an update.Router C came online after Router B sent the RIP update.Router B received an error message indicating the last update was not received.5. How many Telnet sessions can take place simultaneously on a router running a standard edition of the IOS?458106. Which of the following WAN connection services typically use synchronous communications? (Choose two.)circuit-switchedleased linepacket-switchedEthernetanalog modem services7. Which of the following will add a TFTP server as a fallback source fora router to load an IOS image?Router# boot system tftp 163.150.9.31 c2500-d-l.120-9Router# copy run startRouter# boot system tftp c2500-d-l.120-9.bin 163.150.9.31Router# copy run startRouter# config tRouter(config)# boot system tftp c2500-d-l.120-9.bin 163.150.9.31 Router(config)# exitRouter# copy run startRouter# config tRouter(config)# boot system tftp 163.150.9.31 c2500-d-l.120-9.binRouter(config)# exitRouter# copy run start8. What types of messages are sent periodically by devices configured for CDP?probesbeaconssignalsadvertisementsrouting updatesunicast9. An administrator has made routing protocol changes to a ro uter’s configuration. To ensure that the changes are implemented, the active configuration is saved and the router is reloaded. After the router has initialized, the output on the screen displays "Would you like to enter the initial configuration dialog?[yes/no]:" Why did this dialog appear?There was a POST failure.The incorrect IOS loaded.There was an error in the startup configuration file.The configuration register was set to ignore NVRAM.10. Which command is used to redirect debug information to a device that is connected though a Telnet session? Router# monitorRouter# terminal redirect vty 0Router# terminal monitorRouter# monitor output vty 011. After issuing the show interfaces command, a technician notices the line "Serial1 is down, line protocol is down" in the output. Which of the following are possible reasons for this message output? (Choose three.)There is a mismatch in the encapsulation type on both ends of the link.A Layer 1 issue exists.An interface problem exists.The clockrate was not set during configuration.There is no usable media for the protocol.Keepalive messages are not being sent.12.Refer to the above graphic. When using RIP as the routing protocol, how would Chicago use load balancing to route packets to New York? (Choose two.)by forwarding packets over paths of equal costby forwarding packets according to hop count and speed of the linkby determining which interface has the least traffic and sending to it firstby first determining the speed of the links and then cycling packets through the fastest links firstby cycling packets through interfaces and routes following the same pattern (Router 1, 2, 3) each time13. When would the ROM monitor mode be used? (Choose two.) maintaining routing configuration settingsmodifying the IOS image stored in Flashrunning a limited IOS feature setperforming the bootstrap process14. Which two statements are true about route metrics? (Choose two.)The more factors that make up a metric, the greater the flexibility to tailor network operations.The larger the metric number, the better the path.Routing protocols use metrics to send routing updates to directly connected neighbors.Bandwidth and delay are static metrics used by RIP v1.Ticks, delay, and cost are metrics used by routing protocols.15.Which of the following are valid static IP routes? (Choose three.) RouterB(config)# ip route 192.168.5.0 255.255.255.0 S1 RouterC(config)# ip route 192.168.1.0 255.255.255.0 S1RouterA(config)# ip route 192.168.3.0 255.255.255.0 192.168.2.2 RouterB(config)# ip route 192.168.1.0 255.255.255.0 192.168.2.2 RouterC(config)# ip route 192.168.2.0 255.255.255.0 192.168.4.1 RouterA(config)# ip route 192.168.4.0 255.255.255.0 192.168.2.116. Of the eight network users on the Human Resources department LAN, one cannot connect to the file serv er. The user’s PC has successfully booted but can not see the network. What should be checked first?the PC power cordthe file serverthe PC network interface card LEDsthe LAN switch in the wiring closetthe configuration of the router interface attached to the LAN17. What can be determined from the partial output of the show ip route command displayed below? (Choose two.)R 200.200.200.0/24 [120/1] via 192.168.10.2, 00:00:14, Serial0/0C 192.168.10.0/24 is directly connected, Serial0/0The next update will be in 76 seconds.The next update will be in 16 seconds.The administrative distance is 120 and the metric is 1.The metric is 120 and the administrative distance is 1.200.200.200.0 is configured on Serial0/0.192.168.10.2 is configured on Serial0/0.18. Why is it useful to have an interface description?A user can telnet to the router using the interface description.The interface description is a shortcut way to edit the running-config. The interface description helps identify distant network connections.The interface will remain inactive until an interface description is applied.19.Assume OSPF is being used on all routers. What happens when the link between Router1 and Router2 goes down? (Choose two.)Updates start broadcasting every 30 seconds.Updates start broadcasting every 90 seconds.Link-state advertisements are flooded.Link-state advertisements are sent only to neighboring routers.All routers note the change and adjust routes.All routers ignore the change until the route becomes active again. 20.The internetwork needs to communicate between the hosts connected to the E0 interface of the Utah router and hosts connected to the E0 interface of the Idaho router. The hosts should also have connectivity to the Internet. Which commands must be configured in order to enable this communication? (Choose three.)Idaho(config)# ip route 172.31.1.0 255.255.255.0 172.31.2.1Idaho(config)# ip route 0.0.0.0 0.0.0.0 s0Idaho(config)# ip route 172.31.2.0 255.255.255.0 172.31.2.2Utah(config)# ip route 172.31.3.0 255.255.255.0 172.31.2.1Utah(config)# ip route 172.31.3.0 255.255.255.0 s1Utah(config)# ip route 0.0.0.0 0.0.0.0 s021. Which statement about datagram life is true?Each router increments the TTL value of the datagram until the maximum hop count of the routing protocol is reached. The packet is then returned to the source.The packet is dropped when the router count and the TTL value match. The source is notified that transmission has failed. Each router decreases the TTL value by one until it reaches zero. The datagram is then discarded and a time exceeded for message is sent to the source.The destination device discards the datagram if the TTL value is zero on arrival. An ICMP destination unreachable message is sent back to the source.22.The following access list has been created to prevent traffic from host 204.204.7.122 from accessing the 201.100.11.0 network.access-list 22 deny host 204.204.7.122access-list 22 permit anyWhich group of commands will properly place this access list so that this host is denied access only to the 201.100.11.0 network?RouterA(config)# interface s0/0RouterA(config-if)# ip access-group 22 inRouterA(config)# interface s0/0RouterA(config-if)# ip access-group 22 outRouterA(config)# interface fa0/0RouterA(config-if)# ip access-group 22 inRouterB(config)# interface fa0/0RouterB(config-if)# ip access-group 22 inRouterB(config)# interface s0/0RouterB(config-if)# ip access-group 22 inRouterB(config)# interface fa0/0RouterB(config-if)# ip access-group 22 out23. A network administrator can establish a remote session to a host using the Router> telnet 192.168.1.1command but is unsuccessful when using the Router> telnet Boston command to connect to the same interface. Which of the following could be the problem? (Choose two.)The ip host table on the router is not configured.The command telnet Boston was issued from the wrong router prompt.The routing table is missing.Domain name services are not available.24. Which of the following are functions of a router? (Choose three.)packet switchingextension of network segmentssegmentation of local area networksselection of best path based on a logical addressingselection of best path based on a physical addressingThe commands shown in the graphic were entered to alter the startup sequence of the router. On the next reload, which IOS will be loaded?The router will load c2500-js-l.112-26d.The router will load c2500-d-l.120-9.The router will load the IOS from ROM.The router will boot into ROM monitor mode.26.A network administrator trying to deny Telnet traffic from the 192.5.5.0 network to the 201.100.11.0 network entered the commands shown in the graphic. When monitoring the network, the administrator noticed that Telnet packets were still passing between those networks. What is the cause?The router ignored this type of traffic because it required a standard access list to be configured instead of an extended one. The wrong port was configured for the ACL so Telnet traffic was still allowed.The access list has not been assigned to an interface.The permit ip any any allowed all traffic to pass regardless of the other statements listed in this ACL.Refer to the network graphic. A packet needs to travel from Router F to Router A. Which path would be selected by the RIP routing protocol if the default metrics are used?F, G, E, D, B, AF, E, D, C, AF, E, D, AF, E, D, B, A28. Which of the following is the correct flow of routines for a router startup?load bootstrap, load IOS, apply configurationload bootstrap, apply configuration, load IOSload IOS, load bootstrap, apply configuration, check hardwarecheck hardware, apply configuration, load bootstrap, load IOS29. In the configuration register value 0×2104, which value represents the boot field setting?x2430. ACL statements operate in sequential, logical order. If a condition match is true, the rest of the ACL statements are not checked. If all of the ACL statements are unmatched, what happens to the packet?The packets will be placed in a buffer and forwarded when the ACL is removed.The packets will be sent to the source with an error notification message.The implicit permit any statement placed at the end of the list will allow the packets to flow through uninhibited.The implicit deny any statement placed at the end of the list will cause the packets to be dropped.31. Which of the following would cause the "Message Of The Day" banner to appear? (Choose three.)telnetting into the routerinitiating a debug sessionconfiguring a router for the first timeusing the Aux port to check the current configurationusing the console port to check the current configuration32.The administrator knows that port E0 on router B connects to a small LAN without any routers. Which command can be executed on router B to conserve bandwidth on port E0?no update timersholdown-timer 96poison reverse E0passive-interface E0no triggered updates33. When must a router serial interface be configured with the clock rate command?when the interface is functioning as a DTE devicewhen the interface timers have been clearedwhen the connected DTE device is shut downwhen the interface is functioning as a DCE device34. What are the major characteristics of a wide area network? (Choose three.)connect devices separated by wide geographical areasincludes technologies of FDDI and Ethernetuses serial connections to access bandwidthcommon carriers are needed for connectionstype of connection between a router and a switch35. If the config-register on a router is set to 0×2102, where is the first place the router will look for boot system commands? RAMROMFlashNVRAM36. Why would an administrator use the Telnet application when troubleshooting a network? (Choose three.)It can be used to verify the operation of application layer software between the source and destination.Telnet can use the ICMP protocol to verify a hardware connection and network layer address.It is the most complete testing mechanism available.Remote networks may be accessed via a Telnet session for troubleshooting.Time to Live values are used by Telnet to identify a failure of device between source and destination.37.The network shown in the graphic is using RIP as the routing protocol. Which of the following are true regarding the network discovery process that will occur for this network? (Choose three.)The Palm Beach router will show networks 192.168.7.0 and 192.168.8.0 as directly connected networks.All of the routers will have direct knowledge of the exact topology of the entire network.The Key West router will forward routing table information to the Miami and Palm Beach routers.The Miami router will learn about network 192.168.1.0 from the Key West router.If network 192.168.4.0 becomes unavailable, the Key West router will notify the other routers of this fact in the next update.38. Which of the following are characteristics of the Open Shortest Path First (OSPF) routing protocol? (Choose two.) functions as a link-state routing protocoldiscards packets when the hop count is greater than 15calculates the shortest path to a destination using the Diffused Update Algorithm (DUAL)created as a proprietary routing protocolfloods updates as topology changes occurbroadcasts routing updates every 90 seconds or as triggered by topology changes39. The following line was displayed in the output of the show ip route command.R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0What is the value of the routing metric?312203012040.Refer to the output from the show ip route command. What can be concluded from the output of this router command?A preferred route to the destination has not been set.There are two equal cost paths to network 1.0.0.0.Both interfaces are being used equally to route traffic.A variance must be set to load-balance across multiple paths.41. Which of the following are true statements about creating and applying access lists? (Choose three.)Access list entries should filter in the order from general to specific.One access list per port per protocol per direction is permitted.Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination. There is an implicit deny at the end of all access lists.Statements are processed sequentially from top to bottom until a match is found.The inbound keyword refers to traffic entering the network from the router interface where the ACL is applied.42. Which of the following are true regarding the setup configuration mode? (Choose three.)To abort the setup mode, use the CTRL+SHIFT+6 keys.To abort the setup mode, use the CTRL+C keys.Setup mode allows a complete configuration of the router.To enter setup mode, use the privileged mode setup command.A router that does not find a valid IOS during the boot process will start the system configuration dialog.A router that does not find a valid configuration file during the boot process will start the system configuration dialog.43. Which of the following are necessary for basic network communication to occur between hosts that will run such applications as Telnet, web browsers, and e-mail? (Choose three.)TCP/IP must be installed and properly configured on each device.。
《CCNA计算机网络基础》教学大纲
《CCNA计算机网络基础》教学大纲课程编号：课程类别：专业课程课程性质：必修总学时：102 理论学时：68 实验学时：34开课对象：网络技术及相关专业一、课程的性质、目的和任务本课程是思科关于计算机网络技术基础知识的一门课程，为网络技术的专业基础课。
通过本课程的学习，使学生掌握计算机网络的基础知识，了解数据通信的原理，熟悉计算机网络的组成与体系结构、TCP/IP模型，掌握局域网工作原理和一种流行局域网的应用，了解计算机网络管理和结构化布线的基本概念，并培养学生具备简单的组网与网管能力，从而为今后从事计算机网络的应用、设计与开发打下基础。
二、先修课程及预备知识《计算机组成原理》三、课程内容、基本要求及学时分配1、计算机网络基本概念（6学时）[1] 计算机网络的定义[2] 计算机网络的发展过程[3] 计算机网络的分类[4] 计算机网络的功能与应用[5] 计算机网络的组成[6] 计算机网络的拓扑结构基本要求：① 了解计算机网络的发展过程，计算机网络的功能与应用。
② 掌握计算机网络的定义和分类，计算机网络的组成，计算机网络的拓扑结构。
2、计算机网络体系结构（6学时）[1]网络体系结构概述[2] ISO/OSI网络参考模型[3] TCP/IP模型[4] OSI 和 TCP/IP模型的区别基本要求：①了解 OSI 和 TCP/IP模型的区别。
②理解网络分层的作用和含义。
③掌握服务、接口和协议的概念，熟练掌握OSI 的层次结构, 各层的PDU单元及主要功能，TCP/IP 的层次结构，各层的主要功能。
3、应用层（10学时）[1] 应用层概述[2] TCP/IP的应用层基本要求：①理解应用层的功能与作用②掌握TCP/IP的应用层的主要应用及工作原理（包括DNS服务、 HTTP服务、 FTP 服务和-mail服务）4、OSI传输层 (10学时)[1] 传输层功能概述[2] TCP/IP的传输层[3] TCP协议[4] UDP基本要求：①了解TCP协议的功能与特点，TCP的主要实现机制，套接字和端口概念。
CCNA安全第二版课程设计
CCNA安全第二版课程设计一、课程简要介绍CCNA安全课程是面向网络安全工程师和网络管理员设计的，在该课程中，学生将学习如何为企业网络提供基本的安全性能，例如，如何建立安全性基础设施，实现网络安全特征，配置基本安全服务和维护安全设备。
CCNA安全课程提供的基本网络安全知识和技能，可以为从事网络管理、信息安全、系统管理和网络设计的IT专业人员等提供一个全面的安全基础。
本次课程为CCNA安全第二版课程设计，全面更新了课程内容，使得学生能够更好地理解和应用网络安全相关技术。
二、课程目标CCNA安全课程将帮助IT专业人员了解网络安全的基本概念，掌握网络安全的技术和工具，如网络安全配置、网络监测和安全漏洞管理，以及它们在不同实际环境中的应用，从而帮助加强企业网络的安全性。
课程的目标是让学生：1.了解网络安全的基本概念和原则；2.掌握网络安全相关的技术和工具，如网络安全配置、网络监测和安全漏洞管理；3.掌握网络安全的实践应用，包括网络安全对策、网络安全审计和网络安全事件处理等；4.专业知识与技术实践相结合，提升网络安全技能和职业素养。
三、课程大纲第一章：网络安全原理•学习网络安全的基本概念和原则，包括保密性、完整性、可用性、授权和认证、可靠性等；•了解常见的网络攻击类型，如中间人攻击、DoS攻击、DDoS攻击、ARP攻击和IP欺诈等；•掌握网络安全工具和技术，包括网络安全配置、网络监测和安全漏洞管理等。
第二章：防火墙和VPN•学习防火墙的原理和技术；•掌握防火墙的设计和实施；•掌握网络VPN的原理和技术，如IPSec、PPTP、L2TP等。
第三章：入侵检测和防御•学习入侵检测和防御的原理和技术；•掌握入侵检测系统(IDS)的配置和使用；•掌握入侵防御系统(IPS)的配置和使用。
第四章：网络安全管理•了解网络安全管理的概念和技术；•掌握网络安全对策的原理和方法；•掌握网络安全审计的原理和方法；•掌握网络安全事件处理的原理和方法。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
C C N A2F i n a l E x a m参加考试 - ERouting Final Exam - CCNA Exploration: 路由协议和概念 (版本 4.0)1.请参见图示。
哪一项是对连接到路由器 R1 的路由的最有效总结？198.18.0.0/16198.18.48.0/21198.18.32.0/22198.18.48.0/23198.18.49.0/23198.18.52.0/222.下列关于路由协议的陈述，哪三项是正确的？（选择三项。
）EIGRP 支持不等价负载均衡。
RIP 无法配置为允许无类路由。
OSPF 在多路访问链路上选举指定路由器。
RIP 不通告跳数超过 15 的路由。
EIGRP 使用广播流量与其邻居建立相邻关系。
OSPF 能够更迅速地收敛，因为在后继路由失效时，它能够在其拓扑表中找出可行后继路由。
3.请参见图示。
该网络正在运行 RIP 路由协议。
网络 10.0.0.0 突然断开。
下列有关此拓扑结构中路由器如何响应该事件的陈述中，哪一项是正确的？Router4 将在 30 秒之后的下一次定期更新中获知该失效路由。
在抑制计时器超时之前，水平分割将阻止 Router4 向 10.0.0.0 网络转发数据包。
Router5 将立即从路由表中清除这一失效路由。
Router5 将向 Router4 发送触发更新，其中网络 10.0.0.0 的度量为 16。
4.请参见图示。
根据图中所示的拓扑结构，要在 Paris 路由器上配置 EIGRP 需要使用哪三条命令？（选择三项。
）Paris(config)# router eigrp 100Paris(config)# router eigrpParis(config-router)# network 192.168.6.0Paris(config-router)# network 192.168.7.0Paris(config-router)# network 192.168.8.0Paris(config-router)# network 192.168.9.05.请参见图示。
多少条路由既是 1 级路由，又可作为最终路由使用？1234566.请参见图示。
图中的路由器运行的是 EIGRP 路由协议。
关于数据包如何从172.16.1.0/16 网络传输到 192.168.200.0/24 网络的陈述，哪一项正确？路由器会选择所获知的第一条路径，并只将这条路径加入路由表。
路由器会选择管理距离最短的路径，并只将这条路径加入路由表。
路由器会根据通告的网络 IP 地址选择最大的路由 ID，并只将这条路径加入路由表。
路由器会将所有等价路径加入路由表，但只沿一条路径发送数据包，其它则作为主路由无效时的备用路径。
路由器会将所有等价路径加入路由表，并在这些路径上实施等价负载均衡，从而将数据包从多个输出接口发送出去。
7.请参见图示。
从 172.16.1.0/24 网络到 10.0.0.0/24 网络的流量会选用哪条路径？ADCABC流量会在 ADC 和 ABC 之间执行负载均衡流量会通过 ABC 传输，ADC 则作为 ABC 失效时的备用路径。
8.请参见图示。
根据如图所示的输出，下列哪两项陈述是正确的？（选择两项。
）所有路由都处于稳定状态。
每条路由都有一个可行后继。
两台路由器之间的串行接口关闭。
EIGRP 的管理距离已设置为 50。
R1 上已运行了 show ip eigrp topology 命令。
9.请参见图示。
公司网络工程师在路由器上输入以下命令：R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1当工程师在 R1 上输入 show ip route 命令时，路由表没有显示到 10.1.1.0 网络的静态路由。
R1 和 R2 的所有接口都按照图示配置了正确的地址。
要使R1 的路由表显示该静态路由，工程师下一步应该做什么？在路由器 R1 和 R2 中输入默认路由。
启用 R1 和 R2 的串行接口。
配置该静态路由，使用送出接口来取代下一跳地址。
输入 copy run start 命令，强制路由器识别该配置。
10.网络管理员在所示网络图中的路由器 B 和 C 上启用了 RIP。
什么命令可防止向路由器 A 发送 RIP 更新？A(config)# router ripA(config-router)# passive-interface S0/0B(config)# router ripB(config-router)# network 192.168.25.48B(config-router)# network 192.168.25.64A(config)# router ripA(config-router)# no network 192.168.25.32B(config)# router ripB(config-router)# passive-interface S0/0A(config)# no router rip11.网络管理员在 Router_A 上配置了一条默认路由，但该路由没有共享给邻接路由器 Router_B 以及该 OSPF 区域中的其它路由器。
使用哪条命令可以简单快速地将该默认路由配置到 Router_B 及该 OSPF 区域内的所有其它路由器上？Router_A(config-router)# ospf redistribute default-routeRouter_B(config-router)# ospf redistribute default-routeRouter_A(config-router)# default-information originateRouter_B(config-router)# default-information originateRouter_A(config-router)# ip ospf update-defaultRouter_B(config-router)# ip ospf update-default12.为了使运行 OSPF 的路由器通告区域 0 中 172.16.0.0/19 所包含的整个地址范围，网络管理员应使用什么命令？R1(config-router)# network 172.16.0.0 0.0.0.255 area 0R1(config-router)# network 172.16.0.0 0.0.3.255 area 0R1(config-router)# network 172.16.0.0 0.0.15.255 area 0R1(config-router)# network 172.16.0.0 0.0.31.255 area 013.请参见图示。
网络中的所有路由器均运行 RIPv2 和 EIGRP，并且都是默认的路由协议设置，这些路由器的接口上配置的带宽如图所示。
Router1 LAN 和Router5 LAN 之间会使用何种协议，两者之间的流量会如何通过网络进行路由？RIPv2 会在 Router1 和 Router5 之间的两条路径上实施负载均衡。
EIGRP 会在 Router1 和 Router5 之间的两条路径上实施负载均衡。
RIPv2 流量会采用 Router1、Router2、Router5 路径，因为此路径的跳数最少。
EIGRP 流量会采用 Router1、Router3、Router4、Router5 路径，因为此路径具有最佳度量。
14.请参见图示。
网络管理员正在尝试确定为什么路由器 JAX 的路由表中没有OSPF 路由。
所有路由器都配置了 OSPF 区域 0。
从 JAX 路由器上，管理员可以 ping 通与其连接的接口和 ORL 路由器的 Fa0/1 接口，但无法 ping 通其它路由器接口。
网络管理员下一步应采取什么步骤来排查问题？重新启动路由器。
将所有路由器上的 OSPF 进程 ID 更改为 0。
检查 ORL 和 JAX 之间的电缆是否松动。
检查路由器之间是否在传递 CDP 数据包。
使用 show 和 debug 命令确定是否在传播 hello 数据包。
15.下列关于链路状态路由协议的陈述，哪两项是正确的？（选择两项。
）链路状态路由协议了解整个网络的拓扑结构。
链路状态路由协议可以使大型网络快速达到收敛。
链路状态路由协议的路由更新中不包含子网掩码。
链路状态路由协议根据跳数从高到低的顺序来确定最佳路径。
链路状态路由协议不适合具有特定层次结构的网络。
链路状态路由协议仅向直连的邻居发送整个路由表。
16.请参见图示。
BOS Fa0/0 LAN 上的主机能够 ping 通 JAX 路由器的 Fa0/1 接口以及 BOS 和 ORL 路由器上的所有接口。
为什么 10.0.0.0/24 网络中的主机无法 ping 通 JAX 路由器 Fa0/0 LAN 中的主机？JAX 路由器的进程 ID 错误。
JAX 路由器需要 network 10.0.0.0 0.0.0.255 area 0 命令。
JAX 路由器需要 network 192.168.3.0 0.0.0.255 area 0 命令。
BOS 路由器需要 network 192.168.3.0 0.0.0.255 area 0 命令。
17.下列路由器组件和操作的配对中，哪两项是正确的？（选择两项。
）DRAM - 加载 bootstrapRAM - 存储操作系统闪存 - 启动时执行诊断NVRAM - 存储配置文件ROM - 存储备份配置文件POST - 运行硬件模块诊断18.哪三项是 CDP 的特性？（选择三项。
）测试第 2 层连通性提供安全层工作在 OSI 第 2 层和第 3 层默认在每个接口上启用用于调试第 4 层连通性问题提供关于已启用 CDP 的直连设备的信息19.请参见图示。
在路由器上执行如图所示的命令会产生什么效果？所有的口令都将加密。
仅加密 Telnet 会话。
仅加密使能口令。
仅加密使能口令和 Telnet 会话。
将加密使能口令和控制台口令。
20.下列关于 EIGRP 路由操作的描述，哪三项是正确的？（选择三项。
）一旦发现新邻居，便会向邻居表中加入条目。
如果可行后继路由相对于当前后继路由具有更高的通告开销，该可行后继路由即成为主路由。
如果在保持时间内未收到 hello 数据包，则 DUAL 必须重新计算拓扑。
报告距离是邻居通告的与目的地之间的距离。