机械密封行业常用英语汇总
机械业内常用的中英文术语对照
1.3 弯管 Bend
预制弯管 fabricated pipe bend
跨越弯管（^ 形） cross-over bend
偏置弯管（~ 形） offset bend
90巴涔?quarter bend
环形弯管 cirele bend
单侧偏置90巴涔埽? 形） single offset quarter bend
承插焊法兰 socket welding flange
松套法兰 lap joint flange (LJF)
对焊法兰 welding neckflange (WNF)
法兰盖 blind flange, blind
孔板法兰 orifice flange
异径法兰 reducing flange
双夹套垫片 double jacketed gasket
金属包石棉平垫片 flat metal jacketed asbestos filled gasket
整体金属齿形垫片 solid metal serrated gasket
槽形金属垫片 grooved metal gasket
环形连接金属垫片 ring joint metal gasket
螺栓圆 bolt circle (B.C.)
1.5 垫片 Gasket (GSKT)
垫片的型式 type of gasket
平垫片 flat gasket
环形平垫片 flat ring gasket
平金属垫片 flat metal gasket
夹棉织物的橡胶 elastomer with cotton fabric insertion
短半径弯头 short radius elbow
常用化工机械专业英语对照
常用机械专业英语对照Cutting: 切割socket weld 承插焊接fillet weld 角焊 ,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder 馈电线conduit outlet 电线引出口seal fitting 密封接头 , 密封配件Screw thread lubricant螺纹润滑剂 Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧 [ 止动 , 防松 ]垫圈 electrical panel.配电板 ,配电盘nipple 螺纹接头zinc plated.镀锌的ring joint 环接 , 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程 master schedule 主要图表 , 综合图表 , 设计任务书 , 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接 Hard hat：安全帽Goggles：护目镜stockpile 贮存packing list 装箱单crate: 柳条箱purchased material list原材料进货单 back-feed 反馈wire coil 线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block 线弧 , 接头排接线盒 , 接线板 , 线夹power drill 机械钻connector. 接线器insulated sleeve绝缘套管wire connector 接线器wire terminal 电线接头motor lead 电动机引出线power wiring 电力布线tender document．提供证件 orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld 加强焊缝fabrication.制造dye penetrant examination染料渗透试验法 magnetic particle examination 磁粉检验 girth weld 环形焊缝cement lined piping 水泥衬里weld joint 焊缝 , 焊接接头 spool drawing 管路图 , 管路详图 spottest 抽查 , 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly装.配erection 架设examination 试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable 控制电缆操纵索normal bend 法向 [ 法线 ]弯管cable glands: 电缆衬垫exfoliation 剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture 照明器材junction box 分线箱 race way电缆管道terminal box 接线盒distribution board 配电盘 , 配电屏receptacle 插座tumble switch.翻转开关 ,拨动式开关cathodic protection system 阴极保护系统 Circuit breaker 断路开关amplifier panel 放大器盘 control console 控制台 electricalmaterial 电气材料 convenience receptacle电.源插座 cableTIG ： Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod 焊条tensile strength 抗张强度shield gas 保护气体shield jig 保护夹具high frequency generator高.频发电机 welding rod 焊条filler metal 焊料 , 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal. 纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination非.破坏性检验 , qualification: 合格性construction work 施工工程welded joint 焊接缝焊接节点gas cutting.气割arc cutting 电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验 Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment ：对准 ,定位调整check against 检查 , 核对Fixing ：固定Console：控制台cubicle 室,箱audit 审计material certificate.材料合格证vertical panel 竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱 ,磨斜边local panel 现场配电盘fabrication 加工 ,制造instrument rack 计测器支架tank gauge 液面计 flushing冲洗，填缝 analyzer 分析器piping 管道敷设tubing 敷设管道cable fitting 电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理 jig. 夹具arc gouging 电弧刨削chipping 修琢machining 机械加工bridges.管式桥clamp.夹钳压力容器基本词汇安全阀safety valve安装 Installation鞍式支座saddle support凹面 concave半球形封头Hemispherical heads 棒bars保温支撑 insulation support [wiki] 爆炸 [/wiki] 性 explosive泵pump变径段 reducers标记 stamping标志 marking标志的移植 Transferring marking 波纹板 Corrugating Paper补强管reinforcing nozzle补强圈reinforcing ring不锈钢stainless steel不圆度out-of-roundness材料 materials材料证明书 Certification of material 超声检验 Ultrasonic Examination 衬里 Linings成型 Forming成型封头Formed heads尺寸 Dimensions翅片管finned tubes冲击试验impact test传热面积heat transfer surface磁粉检验Magnetic Particle Examination次要应力secondary stress粗糙度 roughness淬火 Quenching带折边的锥形toriconical弹簧 springs弹簧垫圈spring washer弹性模量modulus of Elasticity挡板 baffle plate低合金钢容器low alloy steel vessels低温容器Low-temperature vessels地震烈度seismic intensity垫板 Backing strip垫片 gasket垫圈 washer碟形封头Dished heads顶丝 jackscrew定距管 spacer定位销 pin dowel定义 Definitions毒性 toxicity镀锌容器Galvanized vessels锻件 Forgings对焊 [wiki] 法兰 [/wiki] welding neck flange耳座 lug[wiki] 阀门 [/wiki] valves法兰 flanges法兰接触面Flange contact facings防冲板 impingement baffle防 [wiki] 腐蚀 [/wiki] 衬里Corrosion resistant linings防火 fire protection防涡流挡板vortex breaker非受压件nonpressure parts非圆形容器Noncircular vessels分析 analysis峰值应力peak stress腐蚀裕量corrosion allowance附加载荷supplementary loading附件 attachments复合板 Clad plate覆层容器clad vessels盖板 Cover plates杆 rods and bars刚性 Stiffness高合金容器high-alloy vessels 工作压力operation pressure固定的fixed管板 tube sheet管壳式换热器shell and tube heat exchanger 管口材料表sheet of material for nozzle管口方位nozzle orientation管箱 channel管子 pipes nozzle tube管嘴 nipple罐桶槽 tank过渡段transition in过渡圆角Knuckles焊后热处理after post weld heat treating焊接工艺welding procedure specification焊接接头welding joints焊接系数welding coefficient厚度 thickness滑动的sliding环向应力hoop stress回火 tempering基本地震加速度basic seismic acceleration 基本分压basic wind pressure计算厚度calculated thickness技术条件form of Specification加强圈stiffening rings夹套容器Jacketed vessels检查孔Inspection openings检验 inspection角焊 Fillet welds接地板earth lug截止阀Stop valves介质特性fluid property金属温度Metal temperature筋板 rib plate径向应力radial stress静(压力 )水头 static head局部 areas局部 local局部焊后热处理Local postweld heat treatment矩形设计rectangular design卡箍 clamp开孔补强reinforcement for openings快开盖Quick-actuating closures拉杆 tie rod裂缝 Cracking流体（介质）fluid螺母 nut螺塞 plug螺栓 bolt螺纹 threaded螺柱 studs名义厚度 nominal thickness铭牌 Nameplates内部构件 Internal structures内衬筒 internal shell盘管 coil tube配件 fittings膨胀节 expansion joint平封头 Flat heads评定 Qualification气孔 Porosity气压试验Pneumatic test钎焊 brazing强度 strength of球形封头 spherically dished曲率 curvature屈服 yielding全容积 total volume缺陷 defects群座 skirt support热处理 thermal treatment热处理 heat treatmen热应力 thermal stress人孔 manholes韧性 ductility容积 volume容器 vessel容器净重empty weight容器类别 vessel classification塞焊 Plug welds设计压力design pressure射线超声检验 Radiographic Examination 渗透检验 Penetrant Examination 石墨graphite试样 Test coupons适用范围Scope手孔 handholes水压试验 hydrostatic test/hydraulic test/hydrotest碳钢 carbon steel搪玻璃容器enameled vessels梯子、平台ladders, platforms填充金属 filler metal 凸面 convex凸缘 socket椭圆封头Ellipsoidal heads外压容器 vessels subjected to external pressure未注尺寸公差tolerance grade not noted 无支撑unstayed系数 factor现场安装Field assembly校核 checking of泄放 Discharge泄压装置 Pressure relieving devices性能 properties许用工作压力 allowable working pressure 许用应力 allowable stress 易然的flammable应力腐蚀stress corrosion应力集中 stress concentration预热 Preheating圆度 roundness圆角和倒角 corners and fillets载荷 Loadings胀接 expanded connections折流板 baffle plate蒸发器Evaporators直边长度length of skirt直径 Diameter制造 fabrication制造厂fabricator制造方法methods of fabrication制造工艺fabrication technology周长 Girth主应力primary stress柱状壳体 Cylindrical shells铸铁容器 cast iron vessels转角半径 knuckle radius 装配 assembling 锥度tapered锥壳 conical shell锥形封头Conical heads资格 qualification纵向接头 Longitudinal joints组对 fitting uppipe closure 管塞 end closure端盖 orifice plate 挡板 exialspacing 轴向间距 manufacturetolerance 制造公差acid passivation 酸洗钝化part drawing 零件图stud bolts 双头螺柱化工设备常用词汇和缩写中英文对照化工设备常用词汇和缩写中英文对照缩写 / 英文 /中文AB Anchor Bolt地脚螺栓Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure大气压 Auto Automatic 自动Aux Auxiliary辅助设备、辅助的Avail Available 有效的、可用的Avg Average 平均AW Arc welding 电弧焊AW Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规AWS(AWI) American WeldingSociety(Institute) 美国焊接学会 BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距 BC Bolt circle 螺栓中心圆BD Blow down放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求 BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly Valve碟阀BW Brine Vater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本 cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化 Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost， Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure压力中心 Cpl Coupling 管箍 CplgCoupling 联轴节CR Chloroprene Rubber 氯丁橡胶 CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒D Density 密度Dbl Double 二倍、双DEDD Detail Engineering Design Data 详细工程设计数据Def Definition定义Deg Degree 度、等级Dept Department 部门Des Design 设计Det Detail 详细Detn Determination 确定、决定Dev Deviation 偏差Dev Device 装置DF Design Formula 设计公式Df Deflection 偏斜Dia Diameter 直径Diag Diagram 图Dim Dimension 尺寸Dir Direction方向Disch Discharge 排出、出口Distr Distribution 分布Div Division 部分、区分 DLDoc Document 文件、资料DP Design Pressure 设计压力DP Differential Pressure 压差、分压Dr Drill 钻孔Dr Drive 驱动DW Dead weight 静重、自重DW Demineralized Water 脱盐水Dwg Drawing 图 E East 东EC Elasticity Coefficient 弹性系数Ecc Eccentric 偏心EF Electric Furnace 电炉Eff Efficiency效率eg exempli gratia 例如EHP Effective Horsepower 有效功率EJ Expansion joint 膨胀节EL Elevation 标高Elb Elbow 弯头Elec Electric 电的Elem Element 元素、元件Ellip Ellipsoidal椭球的、椭圆的Emer、 Emerg Emergency 事故、紧急Encl Enclosure 密封、封闭Engrg、Eng Engineering 工程、设计EP Explosion Proof 防爆Eq Equipment 设备Eq Equation 公式、方程式Eq Equivalent 当量ES Electrostatic 静电EST Estimate 估计ESW Electro-Slag Welding 电渣焊ET Eddy Current Examination 涡流检验etc et cetera (and so on)等等Evap Evaporate 蒸发Ex Example 例如Ex Excess 过剩、超过Exam Examination 检验Exh Exhaust 废气、排气Exp Expansion 膨胀Exptl Experimental 实验的Ext External 外部Ext Extreme 极端的FAO Finish All Over 全部加工FAX Facsimile 传真FB Flat Bar 扁钢FCAW Flux Cored Arc Welding 熔剂芯弧焊（手工焊）FDW Feed Water 给水FF Flat Face 平面F/F Field Fabricated 现场制造Fig Figure 图Fin Finish 加工、完成FL Full Load 满载Flex Flexible 挠性Flg Flange 法兰FOB Free On Board 离岸价格FOC Free Of Charge 免费Forg Forging 锻件FOS Factor Of Safety 安全系数FREQ Frequency 频率FST Forged Steel 锻钢Ft Feet 英尺Ftg Fitting 管件、装配F.V. Full Vacuum 全真空FW Fresh Water 新鲜水FW Field Weld 现场焊接FW Fillet Weld 角焊缝GA General Average 平均值Gal Gallon 加仑Gen General 一般、总的Genr Generator 发电机、发生器 GF Groove Face 槽面Gl Glass 玻璃GL Ground Level 地面标高GMAW Gas Metal Arc Welding 气体保护金属极电弧焊Gnd Ground 接地、地面Govt Government 政府GP General Purpose一般用途、通用 Gr Grade 等级Gr Gravity 重力Grd Ground 地面Grp Group 分组、类Gr- wt Gross weight 总重、毛重HB Brinell Hardness 布氏硬度HC Hydrocarbon 烃类HC High Capacity 大容量HD Head 压头Hex Hexagon 六角HH Hand Hole 手孔Hor Horizontal 水平、卧式hp Horsepower 马力HP High Pressure 高压HR Rockwell Hardness 洛氏硬度HRC Rockwell C Hardness C 级洛氏硬度 HS High Pressure Steam高压蒸汽HS Shore Scleroscope Hardness肖氏硬度HSC High Pressure Condensate 高压蒸汽凝液HT High Temperature 高温HT Heat Treatment 热处理HT Hydrostatic Test 水压试验HV Vickers Hardness 维氏硬度Hvy Heavy 重的、重型的HW Hot Water 热水ICW Inter Cooling Water 中间冷却水ID Inside Diameter 内径IF Interface 交接面Illus Illustration说明、图解IN Inlet 进口in Inch 英寸incl Including包括Ind Indicate 指示Ins Insulation 保温INSP Inspection 检验Instl Installation 安装Int Internal 内部的Int Intermediate 中间的Intmt Intermittent 间歇的、间断的I/O Input/Output 输入 /输出Jt Joint 连接、接头KG Kilogram公斤KW(kw) Kilowatt千瓦LAS Low Alloy Steel 低合金钢lb pound 磅LC Level Control 液位控制器Leng Length 长度LF Female Face 凹面Lg Long 长的LG Level Glass 液位计LH Left Hand 左手Lin Linear 线性的Liq Liquid液体Lj Lap joint搭接LJ Lapped Joint 松套LM Male Face 凸面LMTD Logarithmic Mean Temperature Difference 对数平均温差 LN Liquid Nitrogen 液氮LN Level Normal正常液位Lng Lining衬里Lo Lubrication oil润滑油Lo Low 低LOA Length Over-All 全长总长LOC Location 位置Log Logarithm(to the base 10) 对数（以 10 为底）Long Longitudinal 纵向LP Low Pressure 低压LPG Liquefied Petroleum Gas 液化石油气LT Low Temperature 低温LT Leak Testing 气密试验Ltd Limited有限Ltr Letter 字母、信Lub Lubricate 润滑LW Lap Welding 搭接焊LWN Long Welding Neck 对焊长颈LWS Longitudinal Welded Seam 纵向焊缝 M(m) Meter 米、公尺Mach Machine 机器Maint Maintenance 维修Mat(Mat ’l) Material 材料MAWP Maximum Allowable Working Pressure 最大允许工作压力Max Maximum最大MDMT Min. Design Metallic Temperature 最低设计金属温度Mech Mechanical 机械的Mfd Manufactured 制造的Mfr Manufacturer 制造商MG(mg) Milligram毫克MH Manhole 人孔MI Melt Index熔融指数MIG Metal Inert Gas Arc Welding 熔化极惰性气体保护焊Min Minimum最小MIN(min) Minute分钟MJG Metallic Jacketed Gasket 金属包复垫片Mk Mark标志ml Milliliter毫升mm Millimeter毫米MP Medium Pressure 中压MPC Maximum Permissible Concentration 最大许用浓度MS Medium Pressure Steam 中压蒸汽 MS Medium Steel 中碳钢MSL Mean Sea Level 平均海平面MT Magnetic Particle Examination 磁粉检测Mtd Mounted 安装、装配MTR Material Testing Report 材料试验报告MU Measurement Unit 测量单位MV Mean Value 平均值MW Mineral Wool矿渣棉N North 北NA Not Applicable 不适用的NAT Natural 天然的Natl National 国家的NC America National Coarse Thread 美制粗牙螺纹NDT Nondestructive Testing 无损检验Neg Negative 负NF American National Fine Thread 美国细牙螺纹Nip Nipple 螺纹管接头、短节Nom Nominal 名义Nor Normal 正常NOZ Nozzle 接管NPS American Standard Straight Pipe Thread 美国标准直管螺纹NPSHA Net Positive Suction Head Available 有效汽蚀裕量NPSHR Net Positive Suction Head Required 要求汽蚀裕量NPT American Standard Taper Pipe Thread 美国标准锥管螺纹NT Net Tonnage 净吨数NTP Normal Temperature and Pressure 标准温度和压力NTS Not To Scale 不按比例Num Number 数、编号、号码Obj Object 目标、对象OC Operating Characteristic 操作特性OD Outside Diameter 外径OH Open Hearth 平炉Oper Operating 操作Opp Opposite 对面、相反OR Outside Radius 外半径OR Outside Ring 外环Orien Orientation 方位Ovhd Overhead 高架的、顶部的Oxyg Oxygen 氧 P Page 页P Pressure 压力Par Parallel 平行Para Paragraph节、段PE Polyethylene 聚乙烯PFD Process Flow Diagram 工艺流程图Perform Performance 性能PF Power Factor 功率因素PID Piping & Instruments Diagram 管道和仪表流程图Pl Plate 板Pneum Pneumatic 气、气动PO Purchase Order 订货单Port Portable 便携式、轻便 Posit Positive 正Posit Position 位置ppb Parts per billion 十亿分之几ppm Parts per million 百万分之几Prod Product 产品Proj Project 项目、工程PS Polystyrene 聚苯乙烯psf Pounds per square feet磅/平方英尺 psi Pounds per square inch磅/平方英寸PT Liquid Penetrants Examination 液体渗透检测PTFE Polytetrafluoroethylene 聚四氟乙烯PVA Polyvinyl Acetate 聚醋酸乙烯PVAL Polyvinyl Alcohol聚乙烯醇PVC Polyvinyl Chloride聚氯乙烯PWHT Post Weld Heat Treatment 焊后热处理 QA Quality Assurance 质量保证QC Quality Control 质量控制Qty Quantity 数量Qual Quality 质量R Radius 半径Rad Radial 径向RC Rockwell Hardness 洛氏硬度Recip Reciprocate 往复式Recirc Recirculate 再循环Recom Recommended 建议、推荐Ref Reference 参照、基准Refract Refractory 耐火材料Reg Regulator 调节器Regen Regenerator再生器、再生塔 Reinf Reinforce 加强Rel Relative 相对Rep Report 报告Rep Repeat 重复Reqd Required 要求、需要的REV Revision 修改、版次RF Raise face 突台面RH Relative Humidity 相对湿度RH Right Hand 右手RMS Root Mean Square 均方根 ROT Rotating 旋转rpm revolutions per minute 转/分rps revolutions per second 转/秒RT Radiographic Examination 射线照相检验S South 北SAW Submerged Arc Welding 埋弧焊 Sc Scale 刻度、比例SC Standard Condition 标准状态（温度压力）SCH Schedule 表号、管厚号、进度Sec Second 秒Sec Section 剖面、节、段Seg Segment 节、段 SepSeparator 分离器 SeqSequence次序、顺序 SGSpecific Gravity 比重 SHPShaft Horsepower 轴马力SI Standard International 国际单位制Sig Signal 信号Sld Solid 固体SMAW Shield Metal Arc Welding 手工焊Smls Seamless 无缝的SO Slip on 平焊（法兰）Sol Solution 溶液SP Spare parts备件Sp Special 特殊的、专门的SP Static pressure静压力Spec Specification 说明、规定SpGr Specific Gravity 比重Sq Square 方形、平方SR Stress Relief 消除应力SS Stainless Steel不锈钢 Sta Station 站STD Standard 标准STDWT Standard Weight 标准重量STL Steel 钢STP Standard Temperature and Pressure 标准温度和压力Suc Suction 吸入Suppl Supplement 补充SW Shop Welding 车间焊接SW Spot Weld 点焊SW Socket Welding 承插焊（法兰）SWP Safety Working Pressure安全工作压SYM Symmetry 对称SYS System 系统T Ton 吨TC Tungsten Carbide 碳化钨 Tech Technique 技术TEMA Tubular Exchanger Manufacturers Association 管壳式换热器制造商协会（美国）Temp Temperature 温度Term Terminal 终端、接头Thk Thickness 厚度TIG Tungsten Inert Gas Arc Welding 钨极惰性气体保护焊TL Tangent line 切线Tol Tolerance 公差Tot Total 总Trans Transfer 输送器TW Total Weight 总重TW Tack Welding 定位焊Typ Typical 典型、标准UNC Unified National Coarse Thread 统一标准粗牙螺纹UNF Unified National Fine Thread 统一标准细牙螺纹US Undersize 尺寸过小UT Ultrasonic Examination 超声波探伤UTS Ultimate Tensile Strength 抗拉强度极限Vac Vacuum 真空Vap Vapor 蒸汽Var Variable 变化、变量Vel Velocity 速度Vert Vertical 垂直Vol Volume 体积VT Visual Testing 宏观（目测）检查W Watt 瓦WL Welding Line 焊缝线WL Water Line 水线WPS Welding Procedure Specification 焊接工艺规程WP Working Pressure 工作压力WRC Welding Research Committee 焊接研究委员会（美国）WS Water Supply 供水WT Weight 重量W/V Wind Velocity风速XR X-Ray X 射线Yd Yard 码Yr Year 年external/outide diameter 外径grease 油污。
密封件行业英语资料
密封件行业英语资料密封件是一种在工业生产中广泛使用的材料，它具有防封闭空间内物质外泄的功能。
密封件通常由橡胶、塑胶、纸制品等材料制成，有多种形状和尺寸可供选择。
它在汽车、航空航天、化工、电子等领域起着关键作用，因此学习与密封件相关的英语资料对于从事相关行业的人士来说是非常重要的。
首先，我们来了解一些与密封件有关的基础英语术语。
密封件在英文中通常称为seal，指的是一种将两个或多个物体连接在一起，并阻止物质外泄的装置。
同样地，密封件的英文也可以用sealing gasket来表示。
另外，密封件通常可以分为静密封件（static seal）和动密封件（dynamic seal）。
静密封件适用于不需要频繁运动的场合，如管道的接口、容器的盖子等；而动密封件则适用于需要频繁运动的场合，如活塞密封、轴封等。
在生产密封件时，往往需要进行一系列的测试，以确保其质量符合要求。
这些测试可以包括密封性能测试（sealing performance test），压缩变形测试（compression deformation test），耐温测试（temperature resistance test）等。
通过这些测试，生产商可以评估密封件的性能，并进行必要的改进。
此外，还有一些特殊的测试技术，如硬度测试（hardness test），拉伸强度测试（tensile strength test），以及化学成分分析（chemical composition analysis），可以提供更详细的信息，保证密封件的质量。
在密封件行业，产品的设计和制造是非常重要的环节。
在英语中，产品设计可以用product design来表示，制造过程可以用manufacturing process来表示。
当涉及到设计方面时，需要考虑到密封件的尺寸、形状、材料等因素。
这些因素对于密封件的性能和使用寿命起着至关重要的作用。
在制造过程中，我们会用到一些关键的工艺，比如模具制造（mold manufacturing），注塑成型（injection molding），压缩模压成型（compression molding）等。
常用化工机械专业英语对照
常用机械专业英语对照Cutting: 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接Hard hat：安全帽Goggles：护目镜stockpile贮存packing list装箱单crate: 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector. 接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring控制线路motor lead电动机引出线power wiring电力布线tender document．提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验girth weld环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly.装配erection 架设examination试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable控制电缆操纵索normal bend 法向[法线]弯管cable glands: 电缆衬垫exfoliation剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture照明器材junction box 分线箱race way 电缆管道terminal box接线盒distribution board配电盘, 配电屏receptacle 插座tumble switch.翻转开关,拨动式开关cathodic protection system 阴极保护系统Circuit breaker断路开关amplifier panel 放大器盘control console 控制台electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫TIG：Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod焊条tensile strength 抗张强度shield gas 保护气体shield jig保护夹具high frequency generator.高频发电机welding rod 焊条filler metal 焊料, 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验, qualification: 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳压力容器基本词汇安全阀 safety valve安装 Installation鞍式支座 saddle support凹面 concave半球形封头 Hemispherical heads棒 bars保温支撑 insulation support [wiki]爆炸[/wiki]性 explosive泵 pump变径段 reducers标记 stamping标志 marking标志的移植 Transferring marking波纹板 Corrugating Paper补强管 reinforcing nozzle补强圈 reinforcing ring不锈钢 stainless steel不圆度out-of-roundness材料materials材料证明书Certification of material 超声检验Ultrasonic Examination衬里Linings成型Forming成型封头Formed heads尺寸Dimensions翅片管finned tubes冲击试验impact test储罐storage tank传热面积heat transfer surface磁粉检验Magnetic Particle Examination次要应力secondary stress粗糙度roughness淬火Quenching带折边的锥形toriconical弹簧springs弹簧垫圈spring washer弹性模量 modulus of Elasticity挡板baffle plate低合金钢容器low alloy steel vessels低温容器Low-temperature vessels地震烈度seismic intensity垫板Backing strip垫片gasket垫圈washer碟形封头Dished heads顶丝jackscrew定距管spacer定位销pin dowel定义Definitions毒性toxicity镀锌容器Galvanized vessels锻件Forgings对焊[wiki]法兰[/wiki] welding neck flange耳座lug[wiki]阀门[/wiki] valves法兰flanges法兰接触面Flange contact facings防冲板impingement baffle防[wiki]腐蚀[/wiki]衬里Corrosion resistant linings防火fire protection防涡流挡板vortex breaker非受压件nonpressure parts非圆形容器Noncircular vessels分析analysis峰值应力peak stress腐蚀裕量corrosion allowance附加载荷supplementary loading附件attachments复合板Clad plate覆层容器clad vessels盖板Cover plates杆rods and bars刚性Stiffness高合金容器high-alloy vessels工作温度operation/service temperature 工作压力operation pressure固定的fixed管板tube sheet管壳式换热器shell and tube heat exchanger 管口材料表sheet of material for nozzle管口方位nozzle orientation管箱channel管子pipes nozzle tube管嘴nipple罐桶槽tank过渡段transition in过渡圆角Knuckles焊后热处理after post weld heat treating焊接工艺welding procedure specification焊接接头welding joints焊接系数welding coefficient厚度thickness滑动的sliding环向应力hoop stress回火 tempering基本地震加速度basic seismic acceleration基本分压basic wind pressure计算厚度calculated thickness技术条件form of Specification加强圈stiffening rings夹套容器Jacketed vessels检查孔Inspection openings检验inspection角焊Fillet welds接地板earth lug截止阀Stop valves介质特性fluid property金属温度Metal temperature筋板rib plate径向应力radial stress静(压力)水头static head局部areas局部local局部焊后热处理Local postweld heat treatment矩形设计rectangular design卡箍clamp开孔补强reinforcement for openings快开盖Quick-actuating closures拉杆tie rod裂缝Cracking流体（介质）fluid螺孔holes for screw螺母nut螺塞plug螺栓bolt螺纹threaded螺柱studs名义厚度nominal thickness铭牌Nameplates内部构件Internal structures内衬筒internal shell盘管coil tube配件fittings膨胀节expansion joint平封头Flat heads评定Qualification气孔Porosity气压试验Pneumatic test钎焊brazing强度strength of球形封头spherically dished曲率 curvature屈服yielding全容积total volume缺陷defects群座skirt support热处理thermal treatment热处理heat treatmen热应力thermal stress人孔 manholes韧性ductility容积volume容器vessel容器净重empty weight容器类别vessel classification塞焊Plug welds设计压力design pressure射线超声检验Radiographic Examination渗透检验Penetrant Examination石墨graphite试样Test coupons适用范围Scope手孔handholes水压试验hydrostatic test/hydraulic test/hydrotest碳钢carbon steel搪玻璃容器enameled vessels梯子、平台ladders, platforms填充金属filler metal筒体shell 凸面convex凸缘socket椭圆封头Ellipsoidal heads外压容器vessels subjected to external pressure未注尺寸公差tolerance grade not noted无支撑unstayed系数factor现场安装Field assembly校核checking of泄放Discharge泄压装置Pressure relieving devices性能properties许用工作压力allowable working pressure许用应力allowable stress易然的flammable应力腐蚀stress corrosion应力集中stress concentration预热Preheating圆度roundness圆角和倒角corners and fillets载荷Loadings胀接expanded connections折流板baffle plate蒸发器Evaporators直边长度length of skirt直径Diameter制造fabrication制造厂fabricator制造方法methods of fabrication制造工艺fabrication technology周长Girth主应力primary stress柱状壳体Cylindrical shells铸铁容器cast iron vessels转角半径knuckle radius装配assembling锥度tapered锥壳conical shell锥形封头Conical heads资格qualification纵向接头 Longitudinal joints组对fitting uppipe closure管塞end closure 端盖orifice plate 挡板exial spacing 轴向间距manufacture tolerance 制造公差acid passivation 酸洗钝化part drawing 零件图stud bolts 双头螺柱化工设备常用词汇和缩写中英文对照化工设备常用词汇和缩写中英文对照缩写/ 英文/中文AB Anchor Bolt 地脚螺栓Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium 铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会ASME American Society of Mechanical Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure 大气压Auto Automatic 自动Aux Auxiliary 辅助设备、辅助的Avail Available 有效的、可用的Avg Average 平均AW Arc welding 电弧焊AW Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规AWS(AWI) American Welding Society(Institute) 美国焊接学会BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距BC Bolt circle 螺栓中心圆BD Blow down 放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在…之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit 界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表Bskt Basket 筐BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly Valve 碟阀BW Brine Vater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost，Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate 冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Compn Composition 组分Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure 压力中心Cpl Coupling 管箍Cplg Coupling 联轴节CR Chloroprene Rubber 氯丁橡胶CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒D Density 密度Dbl Double 二倍、双DEDD Detail Engineering Design Data 详细工程设计数据Def Definition 定义Deg Degree 度、等级Dept Department 部门Des Design 设计Det Detail 详细Detn Determination 确定、决定Dev Deviation 偏差Dev Device 装置DF Design Formula 设计公式Df Deflection 偏斜Dia Diameter 直径Diag Diagram 图Dim Dimension 尺寸Dir Direction 方向Disch Discharge 排出、出口Distr Distribution 分布Div Division 部分、区分DL Dead load 静载荷、自重Doc Document 文件、资料DP Design Pressure 设计压力DP Differential Pressure 压差、分压Dr Drill 钻孔Dr Drive 驱动DW Dead weight 静重、自重DW Demineralized Water 脱盐水Dwg Drawing 图E East 东EC Elasticity Coefficient 弹性系数Ecc Eccentric 偏心EF Electric Furnace 电炉Eff Efficiency 效率eg exempli gratia 例如EHP Effective Horsepower 有效功率EJ Expansion joint 膨胀节EL Elevation 标高Elb Elbow 弯头Elec Electric 电的Elem Element 元素、元件Ellip Ellipsoidal 椭球的、椭圆的Emer、Emerg Emergency 事故、紧急Encl Enclosure 密封、封闭Engrg、Eng Engineering 工程、设计EP Explosion Proof 防爆Eq Equipment 设备Eq Equation 公式、方程式Eq Equivalent 当量ES Electrostatic 静电EST Estimate 估计ESW Electro-Slag Welding 电渣焊ET Eddy Current Examination 涡流检验etc et cetera (and so on) 等等Evap Evaporate 蒸发Ex Example 例如Ex Excess 过剩、超过Exam Examination 检验Exh Exhaust 废气、排气Exp Expansion 膨胀Exptl Experimental 实验的Ext External 外部Ext Extreme 极端的FAO Finish All Over 全部加工FAX Facsimile 传真FB Flat Bar 扁钢FCAW Flux Cored Arc Welding 熔剂芯弧焊（手工焊）Fdn Foundation 基础FDW Feed Water 给水FF Flat Face 平面F/F Field Fabricated 现场制造Fig Figure 图Fin Finish 加工、完成FL Full Load 满载Flex Flexible 挠性Flg Flange 法兰FOB Free On Board 离岸价格FOC Free Of Charge 免费Forg Forging 锻件FOS Factor Of Safety 安全系数FREQ Frequency 频率FST Forged Steel 锻钢Ft Feet 英尺Ftg Fitting 管件、装配F.V. Full Vacuum 全真空FW Fresh Water 新鲜水FW Field Weld 现场焊接FW Fillet Weld 角焊缝GA General Average 平均值Gal Gallon 加仑Gen General 一般、总的Genr Generator 发电机、发生器GF Groove Face 槽面Gl Glass 玻璃GL Ground Level 地面标高GMAW Gas Metal Arc Welding 气体保护金属极电弧焊Gnd Ground 接地、地面Govt Government 政府GP General Purpose 一般用途、通用Gr Grade 等级Gr Gravity 重力Grd Ground 地面Grp Group 分组、类Gr- wt Gross weight 总重、毛重HB Brinell Hardness 布氏硬度HC Hydrocarbon 烃类HC High Capacity 大容量HD Head 压头Hex Hexagon 六角HH Hand Hole 手孔Hor Horizontal 水平、卧式hp Horsepower 马力HP High Pressure 高压HR Rockwell Hardness 洛氏硬度HR(hr) Hour 小时HRC Rockwell C Hardness C级洛氏硬度HS High Pressure Steam 高压蒸汽HS Shore Scleroscope Hardness 肖氏硬度HSC High Pressure Condensate 高压蒸汽凝液HT High Temperature 高温HT Heat Treatment 热处理HT Hydrostatic Test 水压试验HV Vickers Hardness 维氏硬度Hvy Heavy 重的、重型的HW Hot Water 热水ICW Inter Cooling Water 中间冷却水ID Inside Diameter 内径IF Interface 交接面Illus Illustration 说明、图解IN Inlet 进口in Inch 英寸incl Including 包括Ind Indicate 指示Ins Insulation 保温INSP Inspection 检验Instl Installation 安装Int Internal 内部的Int Intermediate 中间的Intmt Intermittent 间歇的、间断的I/O Input/Output 输入/输出Jt Joint 连接、接头KG Kilogram 公斤KW(kw) Kilowatt 千瓦LAS Low Alloy Steel 低合金钢lb pound 磅LC Level Control 液位控制器Leng Length 长度LF Female Face 凹面Lg Long 长的LG Level Glass 液位计LH Left Hand 左手Lin Linear 线性的Liq Liquid 液体Lj Lap joint 搭接LJ Lapped Joint 松套LM Male Face 凸面LMTD Logarithmic Mean Temperature Difference 对数平均温差LN Liquid Nitrogen 液氮LN Level Normal 正常液位Lng Lining 衬里LNG Liquefied Natural Gas 液化天然气Lo Lubrication oil 润滑油Lo Low 低LOA Length Over-All 全长\总长LOC Location 位置Log Logarithm(to the base 10) 对数（以10为底）Long Longitudinal 纵向LP Low Pressure 低压LPG Liquefied Petroleum Gas 液化石油气LT Low Temperature 低温LT Leak Testing 气密试验Ltd Limited 有限Ltr Letter 字母、信Lub Lubricate 润滑LW Lap Welding 搭接焊LWN Long Welding Neck 对焊长颈LWS Longitudinal Welded Seam 纵向焊缝M(m) Meter 米、公尺Mach Machine 机器Maint Maintenance 维修Mat(Mat’l) Material 材料MAWP Maximum Allowable Working Pressure 最大允许工作压力Max Maximum 最大MDMT Min. Design Metallic Temperature 最低设计金属温度Mech Mechanical 机械的Mfd Manufactured 制造的Mfr Manufacturer 制造商MG(mg) Milligram 毫克MH Manhole 人孔MI Melt Index 熔融指数MIG Metal Inert Gas Arc Welding 熔化极惰性气体保护焊Min Minimum 最小MIN(min) Minute 分钟MJG Metallic Jacketed Gasket 金属包复垫片Mk Mark 标志ml Milliliter 毫升mm Millimeter 毫米MP Medium Pressure 中压MPC Maximum Permissible Concentration 最大许用浓度MS Medium Pressure Steam 中压蒸汽MS Medium Steel 中碳钢MSL Mean Sea Level 平均海平面MT Magnetic Particle Examination 磁粉检测MTD Mean Temperature Difference 平均温差Mtd Mounted 安装、装配MTR Material Testing Report 材料试验报告MU Measurement Unit 测量单位MV Mean Value 平均值MW Mineral Wool 矿渣棉N North 北NA Not Applicable 不适用的NAT Natural 天然的Natl National 国家的NC America National Coarse Thread 美制粗牙螺纹NDT Nondestructive Testing 无损检验Neg Negative 负NF American National Fine Thread 美国细牙螺纹Nip Nipple 螺纹管接头、短节Nom Nominal 名义Nor Normal 正常NOZ Nozzle 接管NPS American Standard Straight Pipe Thread 美国标准直管螺纹NPSHA Net Positive Suction Head Available 有效汽蚀裕量NPSHR Net Positive Suction Head Required 要求汽蚀裕量NPT American Standard Taper Pipe Thread 美国标准锥管螺纹NT Net Tonnage 净吨数NTP Normal Temperature and Pressure 标准温度和压力NTS Not To Scale 不按比例Num Number 数、编号、号码Obj Object 目标、对象OC Operating Characteristic 操作特性OD Outside Diameter 外径OH Open Hearth 平炉Oper Operating 操作Opp Opposite 对面、相反OR Outside Radius 外半径OR Outside Ring 外环Orien Orientation 方位Ovhd Overhead 高架的、顶部的Oxyg Oxygen 氧P Page 页P Pressure 压力Par Parallel 平行Para Paragraph 节、段Pc Piece 件PE Polyethylene 聚乙烯PFD Process Flow Diagram 工艺流程图Perform Performance 性能PF Power Factor 功率因素PID Piping & Instruments Diagram 管道和仪表流程图Pl Plate 板Pneum Pneumatic 气、气动PO Purchase Order 订货单Port Portable 便携式、轻便Posit Positive 正Posit Position 位置ppb Parts per billion 十亿分之几ppm Parts per million 百万分之几Prod Product 产品Proj Project 项目、工程PS Polystyrene 聚苯乙烯psf Pounds per square feet 磅/平方英尺psi Pounds per square inch 磅/平方英寸PT Liquid Penetrants Examination 液体渗透检测PTFE Polytetrafluoroethylene 聚四氟乙烯PV A Polyvinyl Acetate 聚醋酸乙烯PV AL Polyvinyl Alcohol 聚乙烯醇PVC Polyvinyl Chloride 聚氯乙烯PWHT Post Weld Heat Treatment 焊后热处理QA Quality Assurance 质量保证QC Quality Control 质量控制Qty Quantity 数量Qual Quality 质量R Radius 半径Rad Radial 径向RC Rockwell Hardness 洛氏硬度Recip Reciprocate 往复式Recirc Recirculate 再循环Recom Recommended 建议、推荐Ref Reference 参照、基准Refract Refractory 耐火材料Reg Regulator 调节器Regen Regenerator 再生器、再生塔Reinf Reinforce 加强Rel Relative 相对Rep Report 报告Rep Repeat 重复Reqd Required 要求、需要的REV Revision 修改、版次Rev Review 评论、检查Rev Revolution 旋转、转数RF Raise face 突台面RH Relative Humidity 相对湿度RH Right Hand 右手RMS Root Mean Square 均方根ROT Rotating 旋转rpm revolutions per minute 转/分rps revolutions per second 转/秒RT Radiographic Examination 射线照相检验S South 北SAW Submerged Arc Welding 埋弧焊Sc Scale 刻度、比例SC Standard Condition 标准状态（温度压力）SCH Schedule 表号、管厚号、进度Sec Second 秒Sec Section 剖面、节、段Seg Segment 节、段Sep Separator 分离器Seq Sequence 次序、顺序SG Specific Gravity 比重SHP Shaft Horsepower 轴马力SI Standard International 国际单位制Sig Signal 信号Sld Solid 固体SMAW Shield Metal Arc Welding 手工焊Smls Seamless 无缝的SO Slip on 平焊（法兰）Sol Solution 溶液SP Spare parts 备件Sp Special 特殊的、专门的SP Static pressure 静压力Spec Specification 说明、规定SpGr Specific Gravity 比重Sq Square 方形、平方SR Stress Relief 消除应力SS Stainless Steel 不锈钢Sta Station 站STD Standard 标准STDWT Standard Weight 标准重量STL Steel 钢STP Standard Temperature and Pressure 标准温度和压力Suc Suction 吸入Suppl Supplement 补充SW Shop Welding 车间焊接SW Spot Weld 点焊SW Socket Welding 承插焊（法兰）SWP Safety Working Pressure 安全工作压力SYM Symbol 符号、标志SYM Symmetry 对称SYS System 系统T Ton 吨TC Tungsten Carbide 碳化钨Tech Technique 技术TEMA Tubular Exchanger Manufacturers Association 管壳式换热器制造商协会（美国）Temp Temperature 温度Term Terminal 终端、接头Thk Thickness 厚度TIG Tungsten Inert Gas Arc Welding 钨极惰性气体保护焊TL Tangent line 切线Tol Tolerance 公差Tot Total 总Trans Transfer 输送器TW Total Weight 总重TW Tack Welding 定位焊Typ Typical 典型、标准UNC Unified National Coarse Thread 统一标准粗牙螺纹UNF Unified National Fine Thread 统一标准细牙螺纹US Undersize 尺寸过小UT Ultrasonic Examination 超声波探伤UTS Ultimate Tensile Strength 抗拉强度极限Vac Vacuum 真空Vap Vapor 蒸汽Var Variable 变化、变量Vel Velocity 速度Vert Vertical 垂直V ol V olume 体积VT Visual Testing 宏观（目测）检查W Watt 瓦WL Welding Line 焊缝线WL Water Line 水线WPS Welding Procedure Specification 焊接工艺规程WP Working Pressure 工作压力WRC Welding Research Committee 焊接研究委员会（美国）WS Water Supply 供水WT Weight 重量W/V Wind Velocity 风速XR X-Ray X射线Yd Yard 码YP Yield Point 屈服点Yr Year 年external/outide diameter 外径grease 油污。
机械行业常用英语对照--机械英语
机械行业常用英语对照--机械英语2010年09月05日星期日下午 09:34stamping, press冲压punch press, dieing out press冲床uncoiler &strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上逝世点bottom stop下逝世点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption耗费to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 持续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变更die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓机械行业部分英汉对照按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting &holding furnaces 持续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws &nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支撑系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 持续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools &cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 全能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 主动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal &vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 全能铣床Milling machines,vertical 立式铣床Milling machines,vertical &horizontal 立式及卧式铣床Mold &die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe &tube making machines 管筒制作机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 主动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches &buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手。
机械类常用英语
机械类常用英语机械加工常用刀具英汉对照adjustable spanner 活动扳手angle cutter 角铣刀anvil arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规/圆规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手加工方法滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工机械类常用英语：焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬机械类常用英语：生产类其他OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C/T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size机械类常用英语：生产类Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号机械设计及周边其他用语英汉对照assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重覆载荷riveted joint ?钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割模具厂常用之标准零配件英汉对照air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶/冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料? spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板机械类常用英语：塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EV A ethylene-vinlacetate copolyme 醋酸乙烯共聚物EV A expanded polystyrene泡聚苯乙烯EPSfiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFGpolyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PP polystyrene 聚苯乙烯PSpolytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂冲压机械及周边关连用语英汉对照back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat ?合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机模具工程常用词汇英汉对照die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机机械类常用英语：常用加工机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻床engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂?床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机工程图纸英语Material 材料Notes/Remark 注释ANSI 美国国家标准局ASTM美国材料试验协会finish 最后一道表面处理Anodize 阳极氧化Grain 纹理standard标准Range 范围UNLESS OTHERWISE SPECIFIED 除非另有标明外，请参照备注Tolerances 公差punching direction 冲压方向Right Side 正面TH（thickness)料厚Hardness 硬度Burring side 批锋面Tooling/Die 冲压模JIS 日本工业标准Covex 米位surface cleaning 金属表面清洁处理Degreasing 金属除油处理Solvent degreasing 乳化脱脂alkali degreasing 碱性脱脂electrolytic cleaning 电解清洁vapor degreasing 蒸汽脱脂ultrasonic cleaning 超声波清洁vibrating cleaning 震动清洁barrel cleaning 滚桶清洁brushing 刷光polishing 磨光buffing 抛光electro-polishing 电解抛光。
机械类各行业专业英语词汇
机械类各行业专业英语词汇1. 汽车行业 (Automotive Industry)•Engine（发动机）•Transmission（传动装置）•Suspension（悬挂系统）•Brake（刹车系统）•Steering（转向系统）•Exhaust system（排气系统）•Fuel injection（燃油喷射系统）•Tire（轮胎）•Battery（电池）•Alternator（发电机）2. 航空航天工业 (Aerospace Industry)•rcraft（飞机）•Wing（机翼）•Fuselage（机身）•Cockpit（驾驶舱）•Landing gear（起落架）•Jet engine（喷气发动机）•leron（副翼）•Thrust（推力）•Propeller（螺旋桨）•Avionics（航空电子设备）3. 重工业 (Heavy Industry)•Machinery（机械）•Crane（起重机）•Bulldozer（推土机）•Excavator（挖掘机）•Boiler（锅炉）•Conveyor belt（输送带）•Generator（发电机）•Drill（钻机）•Foundry（铸造厂）•Welding（焊接）4. 电子行业 (Electronics Industry)•Circuit board（电路板）•Microchip（微芯片）•Transistor（晶体管）•Capacitor（电容器）•Resistor（电阻器）•Diode（二极管）•Integrated circuit（集成电路）•Semiconductor（半导体）•Printed circuit board (PCB)（印刷电路板）•Soldering（焊接）5. 工程机械 (Construction Machinery)•Cranes（起重机）•Excavators（挖掘机）•Bulldozers（推土机）•Loaders（装载机）•Rollers（压路机）•Pavers（铺路机）•Concrete mixer（混凝土搅拌机）•Tower crane（塔式起重机）•Trencher（挖沟机）•Forklift（叉车）6. 机床行业 (Machine Tool Industry)•Lathe（车床）•Milling machine（铣床）•Drilling machine（钻床）•Grinding machine（磨床）•Boring machine（镗床）•Shaping machine（拉坯机）•CNC machine tool（数控机床）•Power press（压力机）•Shearing machine（剪板机）•Woodworking machine（木工机械）7. 包装机械 (Packaging Machinery)•Filling machine（灌装机）•Sealing machine（封口机）•Labeling machine（贴标机）•Capping machine（旋盖机）•Wrapping machine（包装机）•Coding machine（打码机）•Shrinking machine（收缩机）•Vacuum packaging machine（真空包装机）•Cartoning machine（装箱机）•Palletizing machine（托盘包装机）8. 纺织机械 (Textile Machinery)•Spinning machine（纺纱机）•Weaving machine（织布机）•Knitting machine（针织机）•Dyeing machine（染色机）•Printing machine（印花机）•Stenter machine（拉伸机）•Embroidery machine（绣花机）•Textile finishing machine（纺织整理机）•Yarn twisting machine（纱线捻接机）•Textile testing equipment（纺织测试设备）9. 精密仪器 (Precision Instruments)•Optical microscope（光学显微镜）•Electronic balance（电子天平）•Spectrophotometer（分光光度计）•Ultrasonic cleaner（超声波清洗机）•Atomic force microscope (AFM)（原子力显微镜）•Mass spectrometer（质谱仪）•X-ray diffractometer（X射线衍射仪）•Scanning electron microscope (SEM)（扫描电子显微镜）•Electron beam lithography (EBL)（电子束曝光机）•Surface profilometer（表面粗糙度仪）10. 医疗器械 (Medical Devices)•MRI machine（核磁共振机）•CT scanner（计算机断层扫描仪）•X-ray machine（X射线机）•Ultrasound machine（超声波仪）•Surgical microscope（手术显微镜）•Electrocardiogram (ECG) machine（心电图机）•Defibrillator（除颤仪）•Anesthesia machine（麻醉机）•Blood pressure monitor（血压监测仪）•Thermometer（体温计）以上是机械类各行业中常见的专业英语词汇。
机械密封常用英语汇总
机械密封行业常用英语汇总1. sealing ring --密封环2. seal face--密封端面3. seal interface--密封界面4. rotating ring--动环/旋转环5. stationary ring--静环/静止环6. compensated ring--补偿环7. un-compensated ring--非补偿环8. seal head--补偿环组件9. primary seal--主密封10. secondary seal--副密封11. auxiliary seal--辅助密封12. auxiliary seal ring--辅助密封圈13. bellows--波纹管14. pushing out ring--撑环15. back-up ring--挡圈16. compensated ring adaptor--补偿环座17. un-compensated ring adaptor--非补偿环座18. spring adaptor--弹簧座19. seal adaptor--波纹管座20. retainer--传动座21. driving screw--传动螺钉22. set screw--紧定螺钉23. snap ring--卡环24. clamp ring--夹紧环25. anti-rotating pin--防转销26. annular seal space--密封腔27. seal chamber--密封腔体28. end cover--密封端盖29. elastic component--弹性元件30. a pair of friction components--摩擦副31. inner circulation--内循环32. outer circulation--外循环33, self circulation--自循环34. flush--冲洗35. flush fluid--冲洗流体36. quench--阻封37. quench fluid--阻封流体38 . buffer fluid--隔离流体39 . temperature adjustable fluid--调温流体40. coolant--冷却流体41. heating fluid--加热流体42. sealed medium--被密封介质43. sealant--密封流体44. pv --pv值(密封流体压力P与密封端面平均滑动速度V的乘积)45 . limiting pv --密封达到失效时的PV值.它表示密封的水平46. working pv --极限PV值除以安全系数47. PcV--端面比压Pc与密封端面平均滑动速度V的乘积48. limiting PcV --密封达到失效时的PcV值.它表示密封材料的工作能力49. working PcV --许用PcV值.极限PcV值除以安全系数50 .leakage rate-- 泄漏量51 .run out--跳动52. wear rate--磨损率53. operating life--工作寿命54. operating period--使用期55 .abortive failure--早期失效56. Operating limits:工作参数57. Speed/velocity:转速58. Combination of material:材料组合59. Halted ring:弹簧挡圈60. Bellows:波纹管61. Retainer:传动套，传动座62. Drive ring:压圈63. Cup gasket:静环套64. Spring retainer:弹簧座65. O-ring: O形圈66. Tension spring:拉簧67. Stationary seat:静环形式/静环基座68. Rotary seat:动环座69. Drive screw:传动螺钉70. Wave spring/Bellow spring:波形弹簧71. Rotary o-ring:动环O形圈72. Stationary o-ring:静环O形圈73. Collar:定位套74. Snap ring/clamp ring:卡环75. Disc/thrust ring:止推环76. Wedge ring:楔形环77. Mating ring:静止环/静环78. Primary ring:动止环/动环79. Inventory:存货80. Agitator:搅拌器81. Cryogenics:低温学82. Mixer:搅拌机83. Refinery:炼油84. Petrochemical:石化85. Pulp:纸浆86. Paramecia:配药87. Desalination:脱盐88. Wastewater:污水89. Impeller:叶轮90. Fit:安装91. Lead:石墨，铅92. Edge:边缘93. Grade:等级94. Secondary sealing element:辅助密封材质95. Hydrostatic:流体静力学的96. Cross-section:横截面97. Material code:材料代码98. Seal size:密封轴径尺寸99. Assembly number:装配代码100. Sulphuric:硫酸101. Nitric acid:销酸102. Phosphoric acid:磷酸103. Hydrochloric:盐酸104. PV—pressure/velocity:压力与转速105. RS—rotating seat:动环座106. Multiplier:增效器107. TC—tungsten carbide:硬质合金108. Pin:销109. Engage:接合,啮合110. Pro剖面/侧面111. Adapter:适配器。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
机械密封行业常用英语汇总
文章来源于：/
1.sealingring--密封环
2.sealface--密封端面
3.sealinterface--密封界面
4.rotatingring--动环/旋转环
5.stationaryring--静环/静止环
pensatedring--补偿环
7.un-compensatedring--非补偿环
8.sealhead--补偿环组件
9.primaryseal--主密封
10.secondaryseal--副密封
11.auxiliaryseal--辅助密封
12.auxiliarysealring--辅助密封圈
13.bellows--波纹管
14.pushingoutring--撑环
15.back-upring--挡圈
pensatedringadaptor--补偿环座
17.un-compensatedringadaptor--非补偿环座
18.springadaptor--弹簧座
19.sealadaptor--波纹管座
20.retainer--传动座
21.drivingscrew--传动螺钉
22.setscrew--紧定螺钉
23.snapring--卡环
24.clampring--夹紧环
25.anti-rotatingpin--防转销
26.annularsealspace--密封腔
27.sealchamber--密封腔体
28.endcover--密封端盖
29.elasticcomponent--弹性元件
30.apairoffrictioncomponents--摩擦副
31.innercirculation--内循环
32.outercirculation--外循环
33,selfcirculation--自循环
34.flush--冲洗
35.flushfluid--冲洗流体
36.quench--阻封
37.quenchfluid--阻封流体
38.bufferfluid--隔离流体
39.temperatureadjustablefluid--调温流体
40.coolant--冷却流体
41.heatingfluid--加热流体
42.sealedmedium--被密封介质
43.sealant--密封流体
44.pv--pv值(密封流体压力P与密封端面平均滑动速度V的乘积)
45.limitingpv--密封达到失效时的PV值.它表示密封的水平
46.workingpv--极限PV值除以安全系数
47.PcV--端面比压Pc与密封端面平均滑动速度V的乘积
48.limitingPcV--密封达到失效时的PcV值.它表示密封材料的工作能力
49.workingPcV--许用PcV值.极限PcV值除以安全系数
50.leakagerate--泄漏量
51.runout--跳动
52.wearrate--磨损率
53.operatinglife--工作寿命
54.operatingperiod--使用期
55.abortivefailure--早期失效
56.Operatinglimits:工作参数
57.Speed/velocity:转速
binationofmaterial:材料组合
59.Haltedring:弹簧挡圈
60.Bellows:波纹管
61.Retainer:传动套，传动座
62.Drivering:压圈
63.Cupgasket:静环套
64.Springretainer:弹簧座
65.O-ring:O形圈
66.Tensionspring:拉簧
67.Stationaryseat:静环形式/静环基座
68.Rotaryseat:动环座
69.Drivescrew:传动螺钉
70.Wavespring/Bellowspring:波形弹簧
71.Rotaryo-ring:动环O形圈
72.Stationaryo-ring:静环O形圈
73.Collar:定位套
74.Snapring/clampring:卡环
75.Disc/thrustring:止推环
76.Wedgering:楔形环
77.Matingring:静止环/静环
78.Primaryring:动止环/动环
79.Inventory:存货
80.Agitator:搅拌器
81.Cryogenics:低温学
82.Mixer:搅拌机
83.Refinery:炼油
84.Petrochemical:石化
85.Pulp:纸浆
86.Paramecia:配药
87.Desalination:脱盐
88.Wastewater:污水
89.Impeller:叶轮
90.Fit:安装
91.Lead:石墨，铅
92.Edge:边缘
93.Grade:等级
94.Secondarysealingelement:辅助密封材质
95.Hydrostatic:流体静力学的
96.Cross-section:横截面
97.Materialcode:材料代码
98.Sealsize:密封轴径尺寸
99.Assemblynumber:装配代码
100.Sulphuric:硫酸
101.Nitricacid:销酸
102.Phosphoricacid:磷酸
103.Hydrochloric:盐酸
104.PV—pressure/velocity:压力与转速105.RS—rotatingseat:动环座
106.Multiplier:增效器
107.TC—tungstencarbide:硬质合金
108.Pin:销
109.Engage:接合,啮合
110.Pro剖面/侧面
111.Adapter:适配器
适用范围
被密封介质∶水、油等一般腐蚀性液体
密封腔压力∶≤0.8MPa
密封腔温度∶–20℃～+100℃
线速度∶≤10m/s
特点
真空器件的密封有两种情况，一种是密封件把充满液态介质的某一容器与外部真空空间分割开。
在这种情况下，密封件的主要作用是防止液态介质漏入真空空间。
另一种情况是密封件把真空内腔与外腔分割开，它的作用是保持要求的真空度。
这种情况比较复杂，因为周围气体介质即使稍微漏入真空腔内，也会使其真空度降低。
如果漏入了腐蚀性气体，真空设备就可能损坏。
在很多情况下，真空度和真空空间的洁净，对真空条件下进行的各种工艺过程的质量有决定性的影响。
真空器件所使用的机械密封在结构上并无特殊之处。
对于上述的第一种情况，通常是采用气密性好的金属波纹管型单端面机械密封。
第二种情况则要用双端面机械密封，若使用单端面密封，势必存在密封端面不能获得润滑的问题。