图纸常见英文词汇
英文图纸常用词汇
SPC=Statistical Process Control（统计过程控制）FAI=First Artical Inspection（首件检测）TOOL/EQUIP：生产工具SUPPLIER：供应商GAUGE：检验量具PRCS PROC：PKB/LABEL：包装/标识INSP/TEST：检测，如果是铸件图纸的话，我想主要是指各种无损检测，XT,UT,MT，及渗压试验等。
国外图纸中的一些实用翻译图纸中的一些实用翻译ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED. 未注焊缝均为连续焊ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm.ALL UNSPECIFIED RADI - R3 未注圆角R3REMOVE ALL BURRS AND SHARP EDGES 所有尖角/棱角倒角并去毛11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH. 总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明)CHANNEL 槽钢RSA 708 角钢70X70X8M30X1.5 pitch M30X1.5的锥螺纹Tackweld 点焊OD 1/4" outside dimension 1/4"的缩写外径直1/4"75 CRS 尺寸为75 材质为冷轧钢板410 OPENING REF 410 开口参考尺寸40 REF 尺寸为40,参考值2.5" BSP 2.5” 圆锥管螺纹2.5" BSPT HEXAGON 2.5” 六角圆锥管螺纹(即对丝)30x2.5 FLAT BAR 30X2.5 扁钢TYP 2 POSNS 2处FEMALE: 内扣(母扣)MALE: 外扣(公扣)偏心轴eccentric shaft销轴PIN开口销COTTER PIN螺杆screw轴承axletree挡圈closing ring弹性挡圈circlip弹簧SPRING紧定螺钉SET SCREW圆螺母ROUND NUT平键FLAT KEY圆螺母ROUND NUT六角螺栓HEX HD BOLT无扣长non-buckle longth平垫圈FLAT WASHER螺母FULL NYLOCK NUT吊环螺钉LIFTING EYE BOLT内六角螺钉SOCKET HEAD CAP SCREW六角螺钉HEX HD SETSCREW轴承隔套distance sleeve of axletree深沟球轴承DEEP GROOVE BALL BEARING 开槽盘头螺钉SLOTTED PAN HEAD SCREW 圆锥滚子轴承TAPERED ROLLER BEARING 推力球轴承THRUST BALL BEARING弹簧垫圈SINGLE COIL SPRING WASHER缩写全称翻译ACCESS Accessory 附件ADJ Adjustable,Adjust 调整ADPT Adapter 使适应ADV Advance 提前AL Aluminum 铝ALLOW Allowance 允许ALT Alternate 改变ALY Alloy 合金AMT Amout 数量ANL Anneal 锻炼ANSL Amer Natl Stds InstituteAPPROX Approximate 大约ASME Amer Society of Mech Engrs ASSEM Assemble 装配ASSY Assembly 装配AUTH Authorized 授权的AUTO Automatic 自动的AUX Auxiliary 辅助的AVG Average 平均AWG American Wire GaugeBC Bolt Circle 螺栓圆周BET Between 之间BEV Bevel 斜角BHN Brinell Hardness Number布氏硬度值BLK Blank ,Block 空白B/NM Bill of Material 材料费BOT Bottom 底部BP or B/P Blueprint 蓝图BRG Bearing 轴承BRK Break 破裂BRKT Bracket 支架BRO Broach 钻孔BRS Brass 黄铜BRZ Bronze 青铜B＆S Brown＆Shape 棕色＆形状BSC Basic 基本的BUSH Bushing 套管BWG Birmingham Wire GaugeC TO C Center-to-Center 中心到中心CAD Computer-Aided Drafting 电脑辅助设计CAM Computer-Aided MfgCAP Capacity 容量CAP SCR Cap Screw 螺帽CARB Carburize 使渗碳CBORE Counterbore 扩孔CCW Counter Clockwise 逆时针CDRILL CounerdrillCDS Cold-Drawn Steel缩写全称翻译EFF Effective 有效的ENCL Enclose,Enclosure 附上ENGR Engineer 工程师ENGRG Engineering 工程学EQLSP Equally Spaced 等距EQUIV Equivalent 相等EST Estimate 估计EX Extra 额外EXH Exhaust 消耗EXP Experimental 实验性的EXT Exension,External 范围,外部FAB Fabricate 伪造FAO Finish All OverFDRY Foundry 铸造FIG Figure 数据FIL Fillet,fillister 带子FIM Full Indicator MovementFIN FinishFLX Fixture 结构FLX Floor.Fluid,Flush 基地,液体,冲洗FLEX Flexible 易弯曲的FLG Flange 边缘FORG Forging 锻炼FR Frame,Front 边框FIG Fitting 装置FURN Furnish 提供FWD Forward 向前GALV Galvanized 电镀GR Grade 等级GRD Grind 磨碎GRV Groove 凹槽GSKT Gasket 垫圈H＆G Harden and Grind 加硬和磨碎HD Head 主要的HDL Handle 处理HDLS Headless 无领导的HDN Harden 使硬化HDW Hardware 硬件HEX Hexagon 六边形HGR Hanger 衣架HGT Height 高度HOR Horizontal 水平的HRS Hot-Rolled SteelHSG Housing 外罩HT TR Heat Treal缩写全称翻译NTS Not to ScaleOA Over All 所有OBS ObsotetcOC On CenterOD Outside Diameter 外直径OPP Opposite 对立OPTL Optional 可选择的OR Outside Radius 外半径ORIG Original 初始的PAT. Patent 专利PATT Pattern 形式PC Piece,Pitch Circle 件，节距圆PCH Punch 打孔PD Pitch DiameterPERF Perforate 打孔PERM Permanent 永久的PERP Perpendicular 垂直的PFD Preferred 首选的PKG Package,Packing 包装PL Parting Line,Places,PlatePNEU PncumaticPNL Panel 面板POL Polish 磨光POS Position,Postive 位置PR Pair 对立PRI Primary 基本的PROC Process 程序PROD Product,Production 产品，产量PSI Pounds per Square InchPT Part,Point 零件，点QTR Quarter 四份之一QTY Quantity 数量QUAL Quality 质量R Radius 半径RA Rockwell Harden,A-ScaleRB Rockwell Harden,B-ScaleRC Rockwell Harden,C-Scale RECD Received 巳收到的RECT Rectangle 长方形REF Reference 相关的REINF Reinforce 增强REL Release,Relief 释放，缓解REM Remove 移除REQD Requird 有需要REE Retainer,ReturnREV Reverse,Revision,Revolution RFS Regardless of Feature Size RGH Rough 粗糙的RH Right Hand 右手RIV Rivet 起皱RM Ream 扩展RND Round 周围RPM Revolutions per Minute RPW Resistance Projection Weld SAE Society of Automotive Engrs SCH Schedule 进度表缩写全称翻译CFS Cold-Finished SteelCH Case HardenCHAM Chamfer 斜面CHAN Channel 渠道CHG Change 改变CHK Check 核查CI Cast Iron 铸铁CIR Circle, Circular 圆周CIRC Circumference 圆周CL Centerline 中心线CLP Clamp 夹子CNC Computer Numerical Control 电脑数值控制COMB Combination 联合COML Commercial 商业的CONC Concentric 同中心的CONN Connect,Connector 连接器COV Cover 盖子CPLG Coupling 联结CQ Commercial Quality 商业等级钢CRS Cold Stds AssociationCRT Cathode Ray Tube 阴级射线管CS Cast Steel 铸铁CSA Canadian Stds AssociationCSK Countersink 埋头孔CSTG Casting 铸件CTR Center 中心CU Cubic 立方米CW Clockwise 顺时针CYL Cylinder,Cylindrical 柱面DBL Double 双倍DEC Decimal 小数DEG Degree 摄氏度DET Detail 详情DEV Develop 发展DFT Draft 草稿DIA Diameter 直径DIM Dimension 尺寸DIST Distance 距离DN Down 向下DP Deep,Diametral Pitch 深度,径节DR Drill,Drill Rod 钻孔DSGN Design 设计DVTL Dovetail 吻合DWG Drawing 图纸DWL Dowel 木钉DWN Drawn 拔出EA Each 每个ECC Eccentric 古怪缩写全称翻译HVY Heavy 重量HYD Hydraulic 水压ID Inside Diameter 内部直径IDENT Identification 鉴定ILLUS Illustration 说明IN Inch 英寸INCL Include,Including 包括INCR Increase 增加INFO Information 信息INSP Inspect 检查INSTL Install 安装INST Instruct,Instrument 指示,工具INT Interior,Internal,Intersect 内部的,内在的,交叉IR Inside Radius 内部半径ISO Internal Stds Organization 国际标准化组织JCT Junction 连结JNT Journal 杂志JT Joint 连接K Key 关键KNRL Knurl 硬节KST KeyseatKWY Keyway 键沟LB Pound 英镑LBL Label 标签LG Length,Long 长度LH Left Hand 左手LMC Least Material ConditionLOC Locate 位于LT Light 光LTR Letter 信LUB Lubricate 润滑MACH Machine 机器MAINT Maintenance 维护MATL Material 材料MAX Maximum 最大MECH Mechanical,Mechanism 机械MED Medium 媒介MFG Manufacturing 制造业MI Malleable Iron 可锻造的铁MIN Minimum, Minute 最小，秒MISC Miscellaneous 混杂的MM Millimeter 毫米MMC Max Material ConditionMS Machine SteelMTG Mouting 装备MULT Multiple 倍数MWG Music Wire GagugNA Not Applicable 不可应用的NATL National 国内的NC Numerical Control 数字电脑控制NEG Negative 忽略的NO. Number 号码NOM Nominal 名义上的NPSM Natl Pipe Straight MechNPT Natl Pipe Tapered缩写全称翻译SCR Screw 螺丝SEC Second 秒SECT Section 部分SEP Separate 独立SEQ Sequence 顺序SER Serial,Series 系列SERR Serrate 锯齿状SF SpotfaceSFT Shaft 轴SGL Single 单个SH Sheet 纸SI Intl System of UnitsSL Slide 使滑动SLV Sleeve 袖子SOC Socket 插座SP Space,Spaced,Spare 空间SPL Special 特别SPEC Specification 规格SPG Spring 跳SPHER Spherical 球体SPRKT Sprocket 链轮齿SQ Square 平方SST Stainless Steel 纯铁STD Standard 标准STK Stock 存货STL Steel 铁STR Straight,Strip 直的SUB Substitute 替代物SUP Supply,Support 供应SURF Surface 表面SYM Symmetrical 对称的SYS System 系统T Teeth,Tooth 牙齿TECH Technical 技术TEMP Template,Temporary模板，暂时的THD Thread 线THK Thick 厚的TOL Tolerance 公差TOT Total 总计TPF Taper per FootTPI Taper per In,Threads per InchTPR Taper 锥形TS Tool SteelTYP Typical 典型UNC Unified Natl CoarseUNEF Unified Natl Extra FineUNF Unified Natl FineUNIV Universal 普遍VAR Variable 变量VERT Vertical 垂直的VOL Volume 音量VS Versus 与．．相对W Wide,Width 宽度WASH Washer 洗衣机WDF Woodruff 车叶草WI Wrought Iron 熟铁WT Weight 重量SAE Extra fine 美国汽车工程师协会的超细牙螺纹例：1/2-28 SAE Extra fine SAE Reg 美国汽车工程师协会的标准系列螺纹例：1/2-20 SAE RegSAE-LT 美国汽车工程师协会的圆锥外螺纹例：1/2-28 SAE-LT。
图纸常见词汇知识分享
• 教学目标 • 教学过程 • 听说练习
2
能看懂、会说、会读和会拼写基本的图 纸英语单词：plan, elevation, section, detail drawings and so on.
3
一、图纸说明
specification [.spesifi‘keiʃən] 规格，详述，说明
总说明 general specification 工程说明 project specification 图纸目录及说明 list of contents and description 图例 legend 采用标准规范目录 list of standards and specification adopted 图纸目录 list of drawings 首页 front page
正立面
侧立面 背立面
10
Elevation
11
5、示意图 diagram ['daiəgræm] Example: 流程示意图 flow diagram
荷载简图 load diagram
12
6、 详图 detail drawing 典型节点 typical detail 节点号 detail no. 局部放大图 detail with enlarged scale
16
配筋图arrangement of reinforcement
•模板图 formwork drawing
17
• 条件图 information drawing • 红线图：property line • 地形图 topographical [.tɔpə'græfikl] map • 土方工程图 earth-work drawing • 展开图 developed drawing • 蓝图 blueprint • 蓝晒图 blueprint drawing • 蓝晒图纸 blueprint paper • 询价图 enquiry drawing • 竣工图 as built drawing • 制图 drafting
机械图纸常用词汇中英文
机械图纸常用词汇中英文1. 弯曲 Bend•弯曲（动词）: Bend•弯曲（名词）: Bend or Curve2. 齿轮 Gear•齿轮: Gear•齿: Teeth•齿轮比: Gear Ratio•齿数: Number of Teeth3. 连接件 Joint•连接件: Joint•机械连接件: Mechanical Joint•螺栓: Bolt•螺母: Nut•锁紧螺母: Locking Nut4. 轴 Axis or Shaft•轴: Axis or Shaft•轴承: Bearing•动力传动轴: Power Transmission Shaft •中心轴: Center Shaft5. 表面处理 Surface Treatment•表面处理: Surface Treatment•镀锌: Galvanization•镀铬: Chrome Plating•涂漆: Painting6. 加工 Process•加工: Process or Machining•锯切: Sawing•钻孔: Drilling•磨削: Grinding•铣削: Milling7. 尺寸 Dimension•尺寸: Dimension•长度: Length•宽度: Width•高度: Height•直径: Diameter8. 正交投影 Orthographic Projection•正交投影: Orthographic Projection •主视图: Front View•侧视图: Side View•顶视图: Top View•截面视图: Sectional View9. 标注 Annotation•标注: Annotation or Dimensioning•尺寸标注: Dimensioning•线性标注: Linear Dimensioning•角度标注: Angular Dimensioning 10. 装配 Assembly•装配: Assembly•部件: Component or Part•螺栓连接: Bolt Connection•焊接: Welding11. 图纸符号 Symbols•图纸符号: Symbols•直线: Line•圆: Circle•箭头: Arrow•平行: Parallel•垂直: Perpendicular12. 孔 Hole•孔: Hole•直孔: Straight Hole•盲孔: Blind Hole•放样孔: Counterbore Hole 13. 螺纹 Thread•螺纹: Thread•内螺纹: Internal Thread•外螺纹: External Thread•公制螺纹: Metric Thread•英制螺纹: Imperial Thread 14. 材料 Material•材料: Material•金属: Metal•不锈钢: Stainless Steel•铝合金: Aluminum Alloy15. 组件 Component•组件: Component•驱动器: Driver or Motor•传感器: Sensor•控制器: Controller以上是机械图纸中常用的一些词汇，你可以在编写或阅读机械图纸时参考这些词汇的中英文对照。
图纸常用词汇中英文对照
AB Anchor Bolt 地脚螺栓Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium 铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会ASME American Society of Mechanical Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure 大气压Auto Automatic 自动Aux Auxiliary 辅助设备、辅助的Avail Available 有效的、可用的Avg Average 平均AW Arc welding 电弧焊AW Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规AWS(AWI) American Welding Society(Institute) 美国焊接学会BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距BC Bolt circle 螺栓中心圆BD Blow down 放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在…之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit 界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表Bskt Basket 筐BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly Valve 碟阀BW Brine Vater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost，Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate 冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Compn Composition 组分Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure 压力中心Cpl Coupling 管箍Cplg Coupling 联轴节CR Chloroprene Rubber 氯丁橡胶CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒WN带颈对焊法兰SO带颈平焊法兰IF整体法兰WN大直径管法兰BL法兰盖LF/SE对焊环松套法兰SW承插焊法兰（HG20616-20623）带颈对焊法兰（WN）密封面形式：突面（RF）凹面（MF）凸面（M）全平面（FF）欍槽面（TG）分配盘/气液分配盘（溢流型和（抽吸）喷射型）顶部入口扩散器（预分配器）催化剂卸出口冷氢箱（包括冷氢管冷氢盘再分配盘）提升管待生斜管/待生滑阀/再生斜管/再生滑阀/辅助燃烧室/旋风分离器/双动滑阀/分布段/溢流斗/溢流管/稀相段/密相段/烧焦罐/沉降器/待生立管/料腿/半再生立管/再生塞阀/烟气集合管/油气集合管出口收集器喷射盘瓷球栅板分配器膨胀催化剂料位/催化剂膨胀前料位回流罩新鲜催化剂低压废催化剂罐反应流出物出口Header 管箱Supporting column支柱Phenum风箱Fan ring风筒Fan deck风机底板Drive assembly驱动组件Forced draught鼓风式/induced draught引风式One-bay单排架Two-bay双排架Sheave皮带轮Item成台设备Plug sheet丝堵板Top plate顶板bottom plate底板end plate端板removable cover plate可卸盖板Stay plate加强板Side fame侧面框架tube spacer定距管Tube support cross-member管子支撑梁Tube keeper管子支撑件Instrument connection仪表接头Stud construction, confined gasket榫槽结构窄垫片Flanged construction, confined gasket凹凸结构窄垫片Full-faced gasket全表面宽垫片Plug header丝堵式管箱Stiffener加强件Front正面Side侧面Box-type plenum 箱型风箱Transition plenum转换风箱Standard fit标准配合Undertolerance负偏差Overtolerance正偏差Special close fit特殊紧配合Tube-hole grooving管孔槽Thread lubrication罗纹润滑Centerline header管箱中心线Centerline nozzle接管中心线Reference line基准线Out-of-plane tolerance不平度公差Holding-down bolts夹紧螺栓The instrument air supply空气供给仪器The louvre characteristic performance curve百叶窗特性曲线Instrumentation仪表Dry-bulb temperature干球温度Max. exposure temp. of elastomeric material弹性材料的最大外露温度For pheumatic positioner气动定位器For pheumatic diaphragm actuators气动隔膜执行机构For rotary unions旋转单元Expanded metal fan guard mesh风机护罩多孔金属网Direct right-angle gear drive齿轮直角直接驱动Belt drive皮带驱动Direct motor drive 电动机直接驱动Fan support 风机支架Suspended belt drive, motor shaft down悬挂皮带驱动，电动机轴朝下Gear box齿轮箱Bearing轴承Coupling联轴器Base plate底板Louvre deflection窗叶挠度Louvre blades in closed position with design load of 2000N/m2设计载荷为2000N/m2的处于关闭状态的窗叶Louvre side frames with uniform design load of 2000N/m2均匀设计载荷为2000的百叶窗边缘框架Length of the span between points of support俩支撑点之间的跨度Platform平台Column支柱Walkway走道Live load动载荷Floor framing平台铺板Columns and brackests支柱及托架Ladders and stairways梯子和脚踏Fan thrust风机推力(internal) refractory linings耐火衬里Wet gas compressor trim coolers湿气压缩机调温冷却器Stripper condenser汽提塔冷凝器Flattening 椭圆度Stripper feed pre-heater汽提塔进料预热器Stripprt 1st reboiler汽提塔第一再沸器Primary absorber bottom pumparound cooler一级吸收塔底循环泵冷却器Low temp. HIC resist KCS低温抗HIC镇静钢Gasoline trim cooler汽油调温冷却器Lean oil trim cooler贫油调温冷却器Fuel gas cooler燃料气冷却器Debutanizer reboiler脱丁烷塔冷凝器Butane product cooler丁烷产品冷却器Propane/propylene rectifier condensers丙烷/丙烯精馏塔冷凝器Mixed C3 cooler混合C3冷却器Residue MPS heater渣油MPS 加热器Feed/ slurry pumparound exchanger进料/油浆循环泵换热器Slurry HP steam generator油浆-高压蒸汽发生器Clarified oil MP steam generator澄清油中压蒸汽发生器Safetyrelated technical manual 产品安全技术说明书Namely, ….即….Specific gravity 比重Fixed tubesheet heat exchanger固定管板式换热器Floating head type heat exchanger浮头式换热器U-tube type heat exchanger U形管式换热器Kettle type heat exchanger釜式换热器Double tube type heat exchanger套管式换热器Slip tubesheet heat exchanger with stuffing box滑动管板填料函换热器Stuffing box heat exchanger填料函式换热器Double sheet heat exchanger双管板换热器Thin tubesheet heat exchanger薄管板换热器Bayonet type heat exchanger插管式换热器Jacket type heat exchanger夹套式换热器Mesh demister 丝网除沫器Skirt shell裙座筒体Cover plate盖板Base plate 底板Straddle equi-spaced跨中均布Bottom head 下封头Weld symbol std.焊缝符号标准Weld forms for NZLS-SHELL C、D类焊缝坡口形式Earthquake deg. 地震烈度“D uplicate”= “复制”“for gas service only”= “仅用于气体工况”0.8mm radius round半径为0.8mm的圆1st sulphur condenser第一硫冷凝器A 0.8mm radius round tool（磨平用）A balancing bellows平衡波纹管A blank head毛坯封头A centre line elevation of 3.5 m at the top exchanger顶层换热器中心线拔高A certificate of conformance性能证书A certified test report合格的试验报告A chord length弦长arc length弧长A circumferential line环向线A coded marking编号标志方法A coefficient of discharge排放系数A computed radial shear计算所得的径向剪切载荷A cone with a knuckle radius有转角半径的锥壳A cone-to-cylinder junction锥壳与圆筒的接逢A definitely determinable yield point有明显屈服点的材料A dimensioned detail sketch of defect location and extent缺陷位臵和范围的尺寸草图A fillet weld with a min. throat dimension角焊缝最小厚度a fine grain practice细化晶粒处理A fixed geographical location固定地理位臵A flare radius扩口半径A forged welding neck flange锻制焊接带颈法兰A given nominal chemical analysis给定的公称化学成分A heated electrode holder已加热电焊条的焊条筒A mockup模拟产品a needle gun for scale清除剥落层的撞针枪A neutral to slightly reducing flame中性至微还原性火焰A non-welded dished head非焊接凸形封头A pad垫板A positive mechanical locking arrangement可靠的机械锁紧装臵A proven quantitative analytical technique有效的定量分析方法A ratio of min. specified yield曲强比A ratio of not less than three to one不小于3：1的比例A recess 1/16 in. deep 开凹型座A reverse curve section反向曲线段A rupture disk holder安全膜夹持器A shallow contaminated area一个浅的污染区A shielding gas is employed采用保护气体transfer mode熔滴过渡形式short-circurting非短路过渡A stayed jacket具有拉撑件的夹套A stiff and lump paste粘稠而多块状物的糊A straight thread直螺纹A substantial lifting device靠可靠的提升装臵A suitable gas leak test适当的气密性试验A telebrinell portable tester便携式布氏测定仪A threaded fastener with a head on one end一端有螺栓头的螺纹紧固件A three to one taper over…在…上形成3：1的泄面A transition section reducer变径过渡段壳体A transition with a slope not exceeding 3:1过渡段其坡度不超过3：1A try cock试验旋塞A uniform force fit with the mating section at the root of the weld 在焊根部位的配合处应均匀贴合A valve data tag阀门数据标签A wet paint surface涂漆的未干的表面A wire penetrameter线型透度计Abnormal pressure caused by deflagration由爆燃引起的异常Above 3 o’clock/ 9 o’clock position高于时钟3点/9点的位臵Abrasive tooling打磨工具Abrupt transition突变过渡Accelerated cooling快速冷却Acceptance by inspector由检验员认为合格Acceptance criteria验收标准Acceptance standard合格标准Access openings通道孔Accessibility of pressure vessels压力容器可达性Accumulation of pressure压力累积Acid etch酸蚀Across, impact test横向冲击试验Acting as partial shell stiffeners做为部分壳体加强圈Actual heat treating temperature实际热处理温度Actual prevailing climatic conditions实际的气候条件Additional reinforcement附加补强Adjacent sliding surface such as guides and disks or disk holders相接触的滑动表面，如导向套、阀瓣、或阀瓣夹持器Adjacent to edges of stay-bolted surface临近用螺栓拉撑的表面周边处Adjoining base material相临母材Adjusting slider调整板Admissible wall thickness最小许可壁厚Aerosol can喷罐Affixed to 安装到…After Finning在和翅片成一体后Agitator device搅拌装臵Air baffle(upper/lower)挡风板Air hardening steels自淬钢Air pocket气袋Air volume风量Alignment tolerance对准公差, 组对公差All hydro-test leakage液压试验发现的所有泄露点Allow. Press. Drop允许压降Allowance for corrosion, erosion, abrasion腐蚀裕量，侵蚀，磨损裕量Alternative design for替代Ambient temperature环境温度Amine lean solution/ rich贫/富胺液Ammonia氨Amount of overlap搭接量An adjustable blow-down construction可调排污结构An aluminum coating on the hot face (gas side)热管板的热面（气体侧）喷一层铝thermally sprayed aluminum热喷铝An angle joint connecting锐角对接焊连接angle joint斜口接头An atmospheric dew point常压露点温度An individual tube hydrostatic test逐根进行液压试验Anchor bolt地角螺栓Anchor plate支撑板Angle beam examination横波检验法Angle of diagonal with longitudinal line对角向线与纵向线的夹角Anti-corrosive coating防酸腐蚀的涂层Anti-galling防卡滞的Any group of aligned indications任何一群或直线分布的显示Any non-hazardous liquid任何非危险性液体Any reduction in thickness任何厚度削薄Any taper at a welded joint焊接接头的任何斜度Apex angle顶角, half-apex angle半锥顶角Apparatus仪器，设备Applied linings, tightness应用忖里, 密封性Approval of new material新材料的批准Appurtenances附属零件Arc or gas welded(W)电焊或气焊Pressure welded (P)压力焊Brazed(B)钎焊（Electric）resistance welded (ERW)电阻焊Arc weld电弧焊Act stud welding电弧螺柱焊Resistance stud welding电阻螺柱焊Atomic hydrogen原子氢焊Stud螺栓焊Electron beam welding电子束焊Flash闪光焊Electroslag电渣焊Explosive爆炸焊Induction感应焊Continuous/intermittent welding连续焊/间断焊Electro-gas welding气电焊Full penetration welding全熔焊Inertia and continuous drive friction welding用储能和连续驱动摩擦焊/惯性…L aser beam激光束焊Capacitor discharge welding电容放电焊Manual welding: flat position, vertical position手工焊：平焊、立焊Oxy-fuel gas氧燃料气焊Thermit铝热焊Spot点焊line线焊seam缝焊Tack/Tack weld定位焊Arc strikes, gouges, and other indication of careless workmanship引弧斑痕，刨痕及其他由于疏忽造成的损失starts引弧stops止弧Arithmetical average deviation计算平均偏差Around openings for welded attachment环绕焊接附件孔口Around openings环绕开孔Arrangement symmetry对称布臵Arrangement symmetry对称布臵equispaced midspan跨中均布Asbestos with suitable binder含有适当粘剂的石棉ASME designated organization ASME指定机构ASME designee ASME代表ASNT=American society for nondestructive testing美国无损检测协会ASTM=American society for testing and material美国试验材料协会At elevated temperature, 在高温情况下/cryogenic 低温下At increments that are within 20% of the range covered （点与点间的）增量应为所覆盖范围的20%At or near the center of the weld在焊逢中间或附近At shop在车间At the edges of the fillet weld在角焊缝焊趾处At the large end在大端At the max. anticipated temperature最大预期温度下At the most critical area最危险的区域At the purchaser’s option基于买方的选择At the smallest cross sectional area在最小横截面Attachment of pressure parts to flat plates to form a corner joint承压件、平板相焊形成角接头Attachment welds连续焊逢Austenitic chromium-nickel stainless steels奥式体铬镍不锈钢Austenitic stainless steel奥式体不锈钢Authentication认证/鉴定Auto-refrigeration自动制冷Average discontinuity hoop stress不连续环向平均应力Avoid overloading the bristles避免刷上沾太多油漆Avoid sharp break避免尖角破裂Axial load per unit circumference单位周长轴向载荷Axial strain轴向应变Back strip剥离Back-chip背面清根Backing device钩圈Backing plate, clad material 覆层材料的垫板Backing strip垫板Baffle cut折流板切口Baffle plate起顶板，挡板Baffle折流板Bare and marred spots裸露点（未上漆的）和损害了的地方Bars and shapes棒材和型材Bars拉杆jacks千斤顶clamps夹具Bar棒Base metal母材Base plate底板Base tube基管Basis for establishing确定的基础Bcup硼铜磷组BAg 硼银组Be applied as a continuous coating in an even manner to achieve a minimum film thickness平坦，最薄的膜Be available in sufficient quantity应有足够用的量Be brought up uniformly to均匀升温Be chamfered or rounded进行倒角或倒圆Be compatible with与…协调、一致Be conducted on water at a tem. Between..and..应采用温度在..和..之间的水来进行Be disconnected隔断Be either staggered or in-line可以相互错开，或并排布臵Be erected at the manufacturer’s works在厂内试安装Be essentially symmetrical with respect to the axis of rotation相对于旋转轴保持基本对称Be examined by sectioning可进行截面检查Be expanded for the full thickness of the tube sheet管只能在管板整个厚度里胀Be explicitly indicated that the unit is subjected to vibrations明确指出换热器会有振动Be formed to the curvature of the shell做成与壳体相对应的曲率Be forwarded to送交Be identified in yellow以黄色标明Be inspected to ascertain complete penetration检查确定是否Be mandatory for 强制性的要求Be multiplied by乘以Be obstructed by被…堵塞Be of streamlined design设计成流线型Be perpendicular to垂直于Be readily rendered inoperative经常失灵Be ready accessible for inspection便于检查Be sampled进行采样Be solution annealed进行固溶退火Be well ground, not cake, thicken or skin（油漆）安放好、不结块、变浓、或结皮Be written in stencil on the yellow bandBead width焊道Beams梁Bearing area承载面积Bearing surface受压面Bend tangent弯处切点Bend test弯曲试验Bending stress弯曲应力Bend弯管Bessemer quality steel贝式体钢Bevel is optional, 45°max.斜度/坡口任意，最大为45°Bevel斜磨/倒角Bind flange法兰盖/盲法兰Black ground, yellow letter黑底黄字Blank flange盲板法兰Blast cleaned surface喷砂清洗过的表面Blow敲击, peening锤击Body-to-bonnet or body-to-yoke bolting阀体和阀盖，阀体和阀轭螺栓Boiler water锅炉水Bolt hole clearance螺孔间隙Bolt lands螺栓载荷Bolt stress螺栓应力Bolt tensioners螺栓紧固件/ 螺栓张紧Bolted flange connection螺栓法兰连接Bolting flange螺栓法兰Bolt螺栓Bonnet封头管箱Booster gas heater增压气加热器Bosses threadsBottom plate of saddle鞍座底板Bottom plate底板Braced and stayed surface拉杆和撑杆表面Braces or stay-bolts of uniform diameter symmetrically spaced等直径并对称布臵的拉撑件或撑条的表面Brace拉杆Bracing拉筋Branch connection支管连接Brazed connections for nozzle接管的钎焊连接Brazed joint钎焊接头Brazed vessel钎焊容器Brazer钎焊工Brazing filler metal ring pre-placed here钎料环预先安放于此Brazing filler metals钎料Breaking pin device安全销装臵Breaking pin housing安全销套Breaking pressure破碎压力Breather valve呼吸阀Brinell hardness布氏硬度Brittle coating脆性涂料Brittle fracture脆性破坏BUB=bubble point沸点Bubble trays 泡罩塔Buckling stress屈曲应力Built-up pad加厚凸缘上Burrs along the hole periphery shall be removal除去管孔周边毛刺Burr毛刺, 毛口Busting test爆破试验But otherwise by…但用其他..方式则不Butt straps对接盖板/对接搭板Butt welded joint对接接头Buttering预堆边焊Buttstraps对接搭板Butt-welding对接焊By capillary attraction借助于毛细管引力Bypass shroud旁路挡板By-pass旁通管Cable clamp索夹Calculated test pressure计算得的试验压力Calculation heat exchanger area计算换热面积Calibrated against a standard deadweight tester经标准的静重式测试仪校正Calibrated at intervals not exceeding six months每隔六个月复检一次Can section罐段head端部exchanger section换热器段nozzle管嘴Capacity certification of pressure relief devices泄压装臵排量证明书Capacity certification test排量的验证试验Carbon content含碳量Carbon in material for welding焊接用材料中的碳Care for handling小心轻放HANDLE WITH CARE: Indicating that contents are fragileCast bronze threaded fittings铸造青铜螺纹连接管配件Cast copper alloy pipe flange铸铜合金公称管法兰Cast ductile vessel可锻铸容器Cast iron circular dished heads铸铁碟形封头Cast iron pipe fittings铸铁管件Cast iron vessel铸铁容器Cast iron plugCast iron standard parts, small铸铁标准部件，小件Cast iron铸铁/生铁Cast material铸造材料Cast, forged, rolled, or die formed standard pressure parts铸，锻，轧，或模具成形的标准受压件Casting quality factor铸造质量系数Casting铸件Catalyst circulation design case催化剂循环设计情况Catch basins滤污器Category B butt joint B类对接接头Category容器类别Caustic service有腐蚀的设备Caustic soda苛性钠Caustic washing tower/ alkaline tower碱洗塔Center of gravity mark重心标识NIL: Indicating position of center of gravity Center of lap搭接中心线Center of weld焊缝中心线Centrifugal castings离心浇注的铸件Ceramic random packing陶瓷散堆填料Certificate of authorization for code symbol stamp规范符号标志的认可证书Certification of nondestructive personnel无损检验人员证明书Certified individual（CI）合格人员Chamfer for pass partition oral part隔板槽倒角Chamfer倒角Channel box管箱Channel cover管箱平盖Channel flange管箱法兰Channel gasket管箱垫片Channel head管箱封头Channel pass partition管箱分层隔板Channel-side gasket管箱侧垫片Charpy impact tests“夏比”冲击试验Charpy V-notch type夏比V形缺口形式Chart草图Checking of Dimension 校核尺寸Cheesecloth粗棉布Chemical analysis for qualification shall be obtained by laboratory methods评定化学分析应当采用化验室分析方法Chemical analysis verification results化学分析验证结果Chemical cleaning connections 化学清洗连接处Chemical composition化学成份Chiller economizer再接触预冷器China state bureau of quality and technical supervision中国质量技术监督局Chip mark on integrally forged vessels整体锻造容器上的缺口标志Chip marks and minor depressions削痕或较小的凹陷Chipping铲chipping hammers; grinding磨abrasive wheels; scraping刮scrapers; gouging刨Chisel凿子chrome-moly steel铬钼钢Chrome铬钢Chromic acid铬酸Circular heads and noncircular heads圆形和非圆形封头Circular plates圆平板Circumferential butt joints with one plate offset单边折边的环向对接接头Circumferential joint 环向连接longitudinal joints纵向接头ring joint圆环形连接Circumferential stress环向应力Circumferential surface圆周表面Circumferential weld环焊缝Clad material覆层材料Clad plate复合板Clad restoration覆层复原Clad sheet复合薄板Clad side覆层侧Clad vessel覆层容器Cladding覆层Clad-stripped surface剥离了覆层的表面Clamp ring夹环Clamp卡箍Clapboard挡板Class of acceptance合格级别Class of welded details焊接细节的类别Classification number牌号Clay treater feed heater白土塔进料加热器Cleaned with a light, non-residue, and chemical solvent使用轻型、无残留化学熔剂Cleaning and developing solution清洗和显影法Cleaning of brazed surfaces钎焊的表面清理Cleaning of welded surface焊件表面清理Clearance between surfaces to be brazed钎焊表面间的间隙Clearance间距Clips夹板/压板/夹持件/夹板/卡子Closing in extensions of the body筒体延伸部分进行收口Closing plug塞堵, cap帽盖Closure bars拉紧杆Closure封闭Clustered indication密集性显示CMGC波齿垫CMR阶梯型填料Coarse ingot structure粗锭结构Coarse ripple粗糙焊波grooves沟槽overlaps焊瘤abrupt ridges陡脊valleys凹坑Cracks裂纹pinholes针孔incomplete fusion未熔合Crater弧坑Coated and cored electrodes and flux带涂层的及药芯的电焊条和焊剂Coated electrodes涂层焊条Coated surface涂漆了的表面Coated with a metallic base waterproof lubricant to prevent galling in use and aqueous corrosion during testing漆上金属防水润滑剂以防止卡滞及在试验过程中出现的水腐蚀Coatings涂层plating电镀Code for construction and acceptance of spherical tanks球形储罐施工和验收规范GB50094 Code number代码Code symbol规范符号Coiler蛇管，盘管Cold bent冷弯Cold differential test pressure冷差试验压力Cold flash drum feed cooler冷闪蒸筒进料冷却器Cold-drawn bars冷拔棒Collapsing pressure垮塌压力Collar boltColor coding色码Column立柱Column塔器Combination of different material不同材料组合Combination units组合容器Combined with pneumatic与气压试验混合Combine-unit组合件Combustible distillates可燃液体Commodity specification 设备规格书Communicating chambers连通室Complete chemical analysis of the overlay完整的堆焊层化学分析Complete fusion and complete joint penetration完全熔合及完全焊透Composite组合件Compresed asbestos gaskets压紧的石棉垫Compressed air service压缩空气锅炉Compression type压环式Compressors压缩机Computation 计算Computed working pressure from hydrostatic test由水压试验计算的工作压力Computer control module计算机控制模数Concave and convex凹面和凸面Concavity凹陷Concentric reducer sections同心变径段Concentric ring wave form disk plate同心环碟片填料Concert with inner surface与内表面吻合Conditioned areas修整区域Cone锥体Conical head锥形封头Conical reducer sections锥形变径段Conical sections圆锥截面Connection size standard连接尺寸标准Conspicuous location显眼的位臵Constant volume process zone定容过程区Construction fixtures建造夹具Construction结构数据Consumable and non-consumable electrode process熔化电极法与不熔化电极法Consumable inserts焊接用可熔化嵌条Contact facing接触面Contact pyrometers接触高温表Contamination污染物recontamination再污染Continuation of shell optional壳体可延伸Continuous full penetration weld连续全焊透焊逢Continuous heat resistance持续耐热Control of stamping打印管理Controlled shot peening控制喷丸Conversion换算Coolant冷却剂Cooling chamber冷却室Cooling rate降温速度Cooling tower fan冷却塔风机Cooling way and time 冷却方式与时间Copper sulfate etching硫酸铜Corner and fillet圆角和倒角Corner joint角接头Corner or tee joints角接或T型接头Corner, fillet角接焊缝，角焊缝Corrected for temperature温度校正Corrections for moisture content of the steam校正蒸汽的含水量Corroded thickness蚀态厚度Corrosion resistant linings防腐蚀忖里Corrosion resistant weld metal overlay cladding抗腐蚀堆焊金属层Corrugated metal, asbestos inserted, or corrugated metal, jacketed asbestos filled内填石棉的波纹状金属或充填夹层石棉的波纹金属Corrugated plate波形板Corrugated shells波纹形壳体Corrugating paper machinery波纹板机械Corrugating paper machinery瓦楞纸机械Cosmetic grinding休整性打磨Counter-current逆流/回流Coupling threadCouplings plugged to prevent damage塞紧以防损坏Coupling管箍/耦合/联结Cover flange外头盖法兰Cover plates/Cover盖板Cracks裂纹seams皱纹laps折叠cold shuts冷隔lamination分层Cradle吊架Crater crack火口裂纹Crimping强压Critical temperature临界温度Cross stray斜撑Curvature of the vessel wall容器壁的弧度，Curvature曲率Cutting oil切削油scale residues剥落的残渣Cutting切割fitting装配and alignment对准CVN impact testing夏比缺口冲击试验Cyclic operation循环工作Cyclical loading循环载荷Cylinder筒体Cylindrical shell 柱状壳体，Cylindrical圆柱形Damp潮湿greasy油污oxidized氧化Dead load静载荷Defective brazing有缺陷的钎焊Defect缺陷Defined limit规定的范围Deflecting baffle导流板Deflection cause linkage挠曲引起泄露Deflector导流装臵Delayed cracking延迟裂纹Demister破沫器Demonstration of density and penetrameter image射线透照的黑度和透度计Dengsity密度Velocity流速pressure drop压降viscosity粘性molecular weight分子量Density密度Deoxaluminite weld-through primer焊接坡口防护涂料Deoxidation脱氧Depentanizer feed-bottoms exchanger脱戊烷塔进料/塔底换热器Deposited weld metal熔焊金属Depth of offset折边深度Derusting去锈Design and construction of large, welded, low pressure storage tanks大型焊接低压贮罐设计和制造API620Design duty设计功率Design for full vacuum@ temper.Design life设计寿命Design margin设计裕度Design or type number of valve阀门设计号或型号Design parameter设计参数Designation名称Detachable chamber独立可分的受压室Detect pressure观察压力Detect surface calibration notches 检测表面标定缺口Detrimental corrosion有害的腐蚀Detrimental discoloration有害变色Deviation背离，（对角线、角度上的）偏差DEW=dew point露点Diagonal white and yellow bands 白黄色斜纹Dial indicating pressure gages表盘指示压力表Diameter exemption直径的豁免Diaphragm type pressure relief valve隔膜式泄压阀Die-stamping for material identification打材料标志硬印Diff. Pressure/ Differential pressure压差Differ in thickness厚度差Diffusible hydrogen limit扩散氢限制Digital reading pressure gages数字压力表Dimensionless factor无量纲系数Dimpled压凹窝的, embossed使凸出Direct firing(DF)直接火容器Discharge of safety valves安全阀泄放Discharge pipe排放管Discharge出料Dished cover球面凸形封头Dished heads碟形Disk-doughnut baffle盘-环行折流板Dismantling拆除installation 安装Displacement measurement test位移测量试验Dissimilar metal welding异种金属焊接Dissimilar weld metal不同金属的焊接Distortion大变形Distribution devices配电装臵Distribution, retention发送，保存Distributor分布器Double curvature双曲率single curvature单曲率Double pipe套管Double weld双道焊Double-jacketed金属包垫片Double-welding双面焊Doubly curved shell两个曲面组成的壳体Dowel 销子Drain opening排尽孔Drainage排放Drilled or bored holes钻孔或镗孔Drips and runs in the path of the weld joint焊道内的防护涂料滴痕或流痕Driving fit打入配合（封头与壳体焊接前）Drop weight test落锤试验Drum圆桶Dry saturated steam干饱和蒸汽Dry weight of total halogen or sulfur or in-organic halogens总卤素或硫或无机卤素干重Ductile cast iron可锻铸铁Due to fatigue or creep由于疲劳或蠕变Dummy tubes O.D.堵管平盖Duplex stainless steel双相不锈钢Duplicate and similar parts相同件和相似件During fabrication/Fitting up制造过程中制造期间Dye penetrant examination of the completed weld 100%的着色渗透探伤Dye stenciling染色镂刻Dye-penetration detection着色探伤Dynamic loading动载荷Each bundle每捆, each lift每个吊运包装, shipping container集装箱Each side of each circumferential welded intersection每一环向接头相交的两侧Earth lug接地板Earth lug接地板anchor bolt地脚螺栓lifting lugs吊耳Eccentricity of shell壳体的偏心度Eddy current test涡流探伤with eddy current methodEdge defects边缘缺陷Edge of plates, metal removal from由加工板边去除金属Effective gasket width有效垫片宽度Effective temp. Difference有效温差Effective thickness of conical section锥形段的等效厚度Efficiency系数Elastic buckling stress弹性失稳应力Elasticity, modulus of弹性模量Elastomer合成橡胶Elbow弯头Electrode core焊芯Electrode rods电焊条electrode wires电焊丝Electrode焊条Elevation above ground拔高/地面高度Ellipsoidal椭圆形, torispherical碟形, hemispherical半球形, conical锥形Ellipsoidal椭圆形hemispherical半球形spherically dished(torispherical)球面凸形（碟形）conical 锥形tori-conical(cone head with knuckle)折边锥形（具有转角区的锥形封头）Elliptical projection technique椭圆发射技术Elongated indication条型显示Embody包含，体现Embrittlement 脆化Employing straight threads使用直螺纹Enameled vessel搪瓷容器Enamel瓷釉Endurance limit疲劳极限Engineering drawings工程设计图纸commodity specification商品规格书Engraving or hard stamping蚀刻或打钢印Enlarged inlet nozzlesEnthalpy-temperature profile: linear热函-温度曲线图：线性的Entirely in spherical portion全部在球体部分Epoxy环氧涂层Equally spaced on two rows均匀分布为两排Equipment setup, calibration, operation, evaluation of examination设备调试、校准、操作、和检测数据评定Equip-spaced mid-span跨中均布Erection weight安装重量Erosion冲蚀Establish a mean analysis确定化学成分平均值Etchant浸蚀剂Etching, of sectioned specimens侵蚀，关于截面试样Evaluation and retests评片与复验Evaporator蒸发器Examination of sectioned specimens剖面试样的检验Examination report（超声波）探伤报告Locate indication area确定指示区域echo height回波高度indication dimensions指示尺寸depth below the surface表面下的深度type of indication指示类型Examined by审核人Excess stock from… material余料Excessive deformation过大的变形Excessive scoring of the plates平板上的深痕Exothermic kits放热包Expanded connection胀接Expansion joint膨胀节Explosion-proof group防爆等级Explosive welding of multiplayer tubes多层管爆炸焊Exposed inside edges内侧裸露出的边缘Exposed left un-welded留下不予焊接的显露部分Extend over…延伸到…Extended heat transfer surfaces延伸的转热面Extended or thickened necks加长或加厚管颈External B31.1 process piping外部B31.1工艺配管。
图纸上英文基本释义
图纸上英文基本释义-A-⏹Angle 角度角落如angle 0°30′max 指该产品所有的拔模斜度不得超过30′-B-⏹Base 基础、基地、出发点如based on AMP dyeing spec 118-5000 即必须以AMP 着色规格为依据。
⏹Boss emboss 的简称。
一般指在壳体平面上的以小块凸起，用于壳体安装在电路板上时确定位置⏹Bottom 低部尽头。
通常在图面上标注时指同一标注尺寸的上部和下部⏹Bright surface 光亮面、光洁面与mat surface相对⏹Burr 毛边、毛口、毛刺指被切割、冲削或钻孔后留在原材料如金属上的粘糙的边或面物质一般用于五金品。
-C-⏹Cadmium 镉一种化学元素是RoHS禁止物质。
⏹Cav. Mark 指产品上的模号标识⏹Cav. 即cavity 指模具的模穴、模腔⏹Center measurement 在中间位置测量⏹Centimeter 厘米公制长度单位1in =2.54cm=25.4mm⏹Cham 即chamfer 斜面一般指产品的倒角，或去掉棱角扣的斜面如：0.65*45°如：C 0.6⏹Character 字符、特征、性质如all character must clear and legible. 指产品上所有的字符标记都必须清晰易辨。
有时也用alphabetical (字母)表示。
两者用意相同⏹Circuit Number 也作circuit No. 电路编号一般在壳体上有标记⏹Clear 清楚、清晰⏹Code 代码、代号如location code AMP or –AMP⏹Color 颜色指塑胶产品的颜色；Discolor 变色、褪色；discoloration 变色、污点⏹Complete 全部的、完全的、完成complete with 拥有⏹Comply 顺从、遵守如parts must comply with 115-1003⏹Compound 混合物、化合物、图面上有时指原材料与色粉（色母）混合后的材料名称。
图纸常见英文词汇
accompanied 附带
sharp 锋利
deges 边界
free from 不受影响
opening 孔、口
emboss/convex 凸形
screw 螺钉
extrusion 挤形
form 成型
punch 冲裁
welding 焊接
taping 攻牙
chamfer 斜角
radius 圆角
full R 全圆角
diameter 直径
length 长度
height 高度
width 宽度
deep 深度
datum line 基准线
burr side 披风面
rolling(grain)direction 料纹方向
arc 圆弧
radius 半径
diameter 直径
degrce 度
an angle of ninety 90度角
base 底
square 尺
图纸常见英文词汇
图纸常见英文词汇Sample Text
一、MATERIAL（材料）
英文 中文 英文 中文 英文 中文
Silicon steel 矽钢
galvanized steel 镀锌钢板
screwdriver 螺丝刀
Electro-galvanized steel(SECC) 电解板
aluminium(al) 铝片
sus304csp-3/4h 不锈钢片
see note 注意看
recommended hole size 建议尺寸
grey 灰色
grain direction磨纹方向
工程图纸词汇
工程图纸词汇不按比例Not to scale （NTS）数据表Data sheet腐蚀裕量corrosion allowance 介质medium起跳压力activated pressure 充装系数filling ratio传热面积heating transfer surface 气密（耐压测试）gas-tight test 气压测试pneumatic test 液压测试hydraulic test牌号grade （焊条牌号grade of welding rod）焊条welding rod 焊丝welding wire焊缝welding seam 无菌空气aseptic air平接头butt joint 皮cladding罐顶法兰top flange 罐顶装置top plant垫圈washer 垫片gasket螺栓bolt 螺母nut螺纹thread 六角螺纹hexagonal thread螺丝screw 铆钉rivet铭牌nameplate 称重器weighing machine封板closing board 可调节支架adjustable leg岩棉mineral wool, rock wool 冷媒coolant, cool medium冷凝水condensate water 法兰盖blind flange抽芯铆钉blind rivet 密封圈seal ring硅橡胶silicon rubber 加强圈reinforcing ring加强筋reinforcing rib 变径管reducer pipe压力传感器pressure transmitter温度传感器temperature transmitter截面section 俯视图top view蝶形封头torispherical head 盘管coil pipe液氨liquid ammonia Mild steel 软钢，低碳钢Polythene 聚乙烯卡箍clamp, hoop Body 阀体Bonnet 阀盖Disc 阀瓣nut 螺母Screw 螺栓Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板Nominal bore 公称通径Nominal Pressure 公称压力Nominal size 公称尺寸Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力blind flange法兰盖,盲板法兰阀门种类：Air valves 空气阀门Stop valves 截止阀Throttle Valves 节流阀Auxiliary valves 辅助（副）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Butt welding valves 对焊连接阀Cock 二通Decompression valves 泄压阀Drainage valves 排水阀Stop Valves截止阀Stop Valves 截止阀T-Cock 三通Triple (tee) valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器(真空泵)Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Ball Valves球阀Deceleration valves 减速阀Gate valve 闸阀Emergency Cut-off Valves 紧急切断阀Exhaust valves 排气阀Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Gauge Valves 仪表阀Hand-operated valves / manual valve手动阀Butterfly Valves 碟阀Hydraulic relay valves 液压继动阀Check Valves止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Liquid Indicator/level indicator液位计Centrifugal Pumps离心泵Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Draining Valves排污阀Restrictor Valves/throttle或节流阀) Safety Valves 安全阀Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀测量工具：Pressure gauge 压力计Vernier caliper 游标卡尺Micrometer 千分尺，测微计Tape measure 卷尺Square 直角尺Ferrite testing gauges 铁酸盐测试计Tubular heat exchanger 管壳式换热器Head-channel 头部管箱Head-bonnet 管箱（封头上的）Head flange-channel（bonnet）头部管箱法兰Stationary Tubesheet 固定管板Floating tubesheet 浮动管板Flange-rear head end 尾部管箱法兰Expansion joint 膨胀节Floating head cover浮头盖Floating head cover flange 浮头盖法兰Packing box 填料函Packing gland 填料压盖Lantern ring 套环Tierod 拉杆Spacer 定距管locating rod Transverse baffle 折流板Impingement plate 防冲板Support plate 支撑板Pass partition 分程板Support saddle 固定鞍座，职称鞍座Backing device 衬垫装置Tube pass（tube-side pass）管程Shell pass (shell-side pass) 壳程焊接方面Acetylene 乙炔Ampere 安培(电流) Angle welding, corner welding，fillet welding 角焊Arc 电弧Argon arc welding 氩弧焊接Butt welding 对接焊接,角焊, 填角焊, 贴角焊Bead welding，overlaying weld 堆焊Fillet weld 填角焊接Laser beam welding 雷射光焊接Spot welding 点焊Skip welding 跳焊automatic weld自动焊接arc-weld电弧焊backing groove of weld焊缝反面坡口all-around weld整周焊connective weld联系焊continuous weld连续焊flat fillet weld平角焊gas-pressure weld气压焊intermittent weld断续焊; 断续焊缝pressure weld压焊pressure-tight weld气密焊; 密封焊道single-pass weld单道焊。
施工图中英文对照词汇表.doc
施工图中英文对照词汇表目录1.密封元件1.1 法兰、法兰盖1.2 螺栓、螺母1.3 垫片1.3.1 常用1.3.2 高压设备用2.基础构件3.梯子平台4.设备常用零部件4.1 筒体封头4.2 支座4.2.1 鞍座、耳座4.2.2裙座4.2.3其它支座4.3 主要零部件5.换热器专用名词6.塔专用名词7.图面节点术语及图面常用语7.1 节点术语7.2 图面常用语8.技术要求及特性表中常用语9.常用技术要求的英文译法10.常用介质11.其他1 密封元件1.1 法兰、法兰盖1）对焊法兰：WELDING NECK FLANGE2）平焊法兰：SLIP-ON FLANGE3）衬环法兰：CLADDED FLANGE4）突面法兰：RAISED FACE FLANGE (RF FLANGE)5）凸面法兰：MALE FLANGE (M FLANGE)6）凹面法兰：FEMALE FLANGE (FM FLANGE)7）榫面法兰：TONGUE FLANGE (T FLANGE)8）槽面法兰：GROOVE FLANGE (G FLANGE)9）法兰盖：BLIND FLANGE1.2 螺栓、螺母1）螺栓：BOLT2）双头螺柱：STUD3）螺母：NUT1.3 垫片GASKET1.3.1 常用1）石棉橡胶板：ASBESTOS SHEET (OR GASKET)2）缠绕垫：SPIRAL WOUND GASKET3）橡胶垫：RUBBER GASKET4）金属包垫：METAL JACKETED GASKET5）石墨垫：GRAPHITE GASKET6）聚四氟乙烯：PTFE. GASKET(POLYTETRAFLUOROETHYLENE GASKET) 1.3.2 高压设备用1）铝平垫：ALUMINIUM PLAT GASKET2）透镜垫：LENS RING3）齿形垫：TOOTHED GASKET4）椭圆垫：OVAL RING5）八角垫：OCTAGONAL RING6）Ω垫：“Ω”GASKET7）双锥垫：CONICAL RING GASKET2 基础构件1）地脚螺栓：ANCHOR BOLT2）模板：TEMPLATE3）锚板：ANCHOR PLATE4）基础构件：FOUNDATION COMPONENT5）筋板：RIB3 梯子平台1）梯子：LADDER2）平台：PLATFORM3）钢隔板：GRATING4）槽钢梁：CHANNEL BEAM5）立柱：POST6）扶手：HANDRAIL7）扁钢：PLAT BAR8）踏步：LADDER RUNG9）连接板：CONNECTION PLATE (OR LUG)10）安全门：SAFETY CHAIN (链式) OR BAR11）角钢：ANGLE STEEL4 设备常用零部件4.1 筒体、封头1）椭圆封头：HEAD2）平盖：PLAT COVER3）半球形：HEMISPHERICAL HEAD4）碟形封头：DISHED HEAD5）锥形：CONICAL HEAD6）折边锥形：FLANGED & CONICAL HEAD7）锥段：CONICAL SECTION8）筒体：SHELL9）多层包扎筒体：LAYERED SHELL10）内筒：INNER SHELL11）层板：LAYER PLATE4.2 支座4.2.1 鞍座：SADDLE耳座：SUPPORT LUG (OR BRACKET)1）垫板：WEAR PLATE (OR PAD)2）底板：BASE PLATE3）筋板：RIB4）腹板：CELIAC PLATE4.2.2 裙座1）筒体：CYLINDER2）盖板：COVER PLATE3）底板：BASE PLATE4）垫板：PAD5）筋板：RIB6）通气孔：VENT HOLE7）进出口：ACCESS OPENING 4.2.3 其他支座1）腿座：SUPPORT LEG4.3 主要零部件1）接管：NOZZLE2）管台：NECK3）补强圈：REIN. RING4）加强圈：STIFF. RING5）铭牌：NAME PLATE6）接地板：EARTH LUG7）防冲板：IMPINGEMENT BAFFLE8）防涡流挡板：VORTEX BREAKER9）液位计：LEVEL GAUGE10）视镜：GLASSES11）补强管：REIN. NOZZLE12）筋板：RIB13）弯头：ELBOW14）管：PIPE15）垫板：PAD PLATE16）人孔：MANHOLE17）手孔：HANDHOLE18）组合视镜：COMBINED GLASSES19）内爬梯：INTERNAL LADDER20）内部扶手：INTERNAL HANDRAIL21）垫圈：WASHER22）吊耳：LIFTING LUG23）管轴式吊耳：LIFTING TRUNNIONS24）板式吊耳：PLATE LIFTING LUG25）内件：INTERNALS26）支承圈：SUPPORT RING27）夹、卡子：CLIP28）保温圈：INSULATION SUPPORT RING 29）弯管：BEND PIPE30）防火螺母：FIREPROOF NUT31）角钢：ANGLE STEEL32）管帽：PIPE CAP33）凸缘：PAD34）丝堵：THREADED PLUG35）一般挡板：BAFFLE36）预焊件：PREWELDED PARTS37）管架：PIPE RACK38）安全阀：SAFETY VALVE39）除沫器：DEMISTER40）激冷环：QUENCH RING41）下降管：DOWNCOMER42）溢流管：OVERFLOW NOZZLE43）螺钉：SCREW44）铆钉：RIVET45）锚栓：ANCHOR46）销钉：PIN47）夹具：JIG48）填料箱：PACKING BOX49）填料压盖：PACKING GLAND50）填料：PACKING51）锥顶：CONE ROOF52）拱顶：COVE ROOF53）加热盘管或蛇管：COIL54）壁板：SHELL PLATE55）底板：BASE PLATE56）边缘板：SIDE PLATE57）中幅板：MIDDLE PLATE58）液封槽：LIQUID SEAL59）消防装置：FIREFIGHTING DEVICE60）排水槽：DRAIN61）夹套筒体：JACKET SHELL62）夹套封头：JACKET ELLIP HEAD63）插入管：SETIN NOZZLE64）复合板：CLAD PLATE65）衬里：LINING66）堆焊层：DEPOSITED LAYER67）高压筒体端部：SHELL END FLANGE68）高压螺栓：HIGH TENSION BOLT5 换热器专用名词1）管束：BUNDLE2）管板：TUBESHEET3）折流板：TRANSVERSE BAFFLE4）弓形折流板：SEGMENTAL BAFFLE5）支持板：SUPPORT PLATE6）换热管：TUBE7）定距管：SPACER8）挡管：DUMMY TUBE9）拉杆：TIE ROD10）防冲板：IMPINGEMENT BAFFLE11）滑道杆：GUIDE ROD (BAR)12）旁路挡板：SEAL STRIP13）分程隔板：PASS PARTITION14）壳体纵向隔板：LONGITUDINAL BAFFLE15）密封条：SEAL STRIP16）U形管：U TUBE17）中间分流挡板：INTERMEDIATE BAFFLE18）浮动管板：FLOATING TUBESHEET19）浮头盖：FLOATING HEAD COVER20）浮头盖法兰：FLOATING HEAD COVER FLANGE21）钩圈：BACKING DEVICE22）平盖管箱：CHANNEL23）凸形封头管箱：CHANNEL24）外头盖：SHELL COVER25）防送支耳：ANTI-LOOSENING LUG26）防松螺栓：ANTI-LOOSENING BOLT27）环首螺钉：EYE BOLT28）顶丝：JACK SCREW29）膨胀节：EXPANSION JOINT30）波纹膨胀节：BELLOWS EXPANSION JOINT31）排污口：DRAIN32）放空口：VENT33）堰板：WEIR34）釜式锥段：CONICAL SECTION35）偏心锥段：ECCENTRIC CONICAL SECTION36）鞍座间调整垫板：SHIM PLATE6 塔专用名词1）塔盘：TRAY2）吊柱：DAVIT3）支持圈：SUPPORT RING4）降液管（板）：DOWNCOMER5）填料：PACKING6）填充物：FILLING7）分布器：DISTRIBUTOR8）再分布器：REDISTRIBUTOR9）泡罩：BUBBLE CAP10）浮阀：FLOATING VALVE11）溢流堰：OVERFLOW WEIR12）受液堰：SEAL PAN13）入口堰：INLET WEIR14）出口堰：OUTLET WEIR15）筛板：SIEVE PLATE16）内件：INTERNALS17）限位板：STOPPER18）拉杆：TIE ROD19）防溅溢流板：DECK20）碎流挡板：STREAM BREAKER21）预焊件：PREWELDED PART22）管架：BRACKET23）栅板：GRATING24）支承块：SUPPORT BLOCK25）就位吊耳：RETAINING LUG7 施工图图面节点术语及图面常用语7.1 节点术语1）壳体纵环焊缝：L&C WELD OF SHELL2）接管与筒体封头焊缝：NOZZLE “A”TO SHELL (HEAD) JOINT 3）接管与法兰焊缝：NOZZLE “A”TO FLANGE JOINT4）带补强圈接管与筒体封头焊缝：NOZZLE WITH REINF . RING TO SHELL(HEAD) JOINT 5）管口方位图：NOZZLE ORIENTATION6）××剖面图：SECTION “××”7）××向视图：VIEW “××”8）法兰与筒体焊缝：FLANGE TO SHELL JOINT9）管板凸缘与筒体焊缝：TUBESHEET TO SHELL JOINT10）管支承拉筋详图：RIB DETAIL OF NOZZLE “A”11）搭接焊缝：LAP WELD12）搭接角焊缝：LAP FILLET WELD13）焊后磨平：RUBDOWN AFTER WELDING14）氩弧焊：TIG（TUNGSTEN-INERT-GAS）ARC WELD15）着色检测：PENETRANT EXAMINATION16）磁粉检测：MEGNETIC EXAMINATION17）×××详图：DETAIL OF ×××18）“U”与“U”焊缝：“U” TO “U” WELD JOINT19）“A”向折流板布置图：VIEW “A”BAFFLE ARRANGEMENT20）换热管与管板连接：TUBE TO TUBESHEET JOINT21）强度焊：STRENGTH WELDED22）密封焊：SEAL WELDED23）强度胀：STRENGTH EXPANDED24）贴胀：LIGHT EXPANDED7.2 图面常用语1）装配图：ASS’Y DWG2）部件图：COM’T DWG3）零件图：PARTS DWG4）零部件图：PART & COM’T DWG5）内件图：INTERNALS DWG6）外部构件图：EXTERNALS DWG7）剖面：SECTION8）详图：DETAILS9）俯视图：VERTICAL VIEW10）侧视图：LATERAL VIEW11）固定端：FIXED SIDE12）滑动端：SLIDING SIDE13）镇静钢：KILLED STEEL14）沸腾钢：RIMMED STEEL15）不锈钢：STAINLESS STELL16）双向钢：DUPLEX STEEL17）热轧的：HOT-ROLLED18）冷轧的：COLD-ROLLED19）淬火的：QUENCH20）正火的：NORMALIZE21）退火的：ANNEAL22）回火的：TEMPER23）固溶：SOLUTION24）可拆的：REMOVABLE25）手工电弧焊：SMAW (SHIELDED METAL ARC WELD) 或MMAW (MANUAL METAL ARC WELD) 26）埋弧焊：SUBMERGED ARC WELD27）定位焊：TACK WELD28）点焊：SPOT WELD29）连续焊：CONTINUOUS WELD30）间断焊：INTERMITTENT WELD31）焊后热处理：PWHT (POST WELD HEAT TREATMENT) 32）红丹：RED-LEAD33）镀锌：GALVANIZATION34）酸洗钝化：PICKLING35）泪孔：WEEP HOLE36）半圆孔：SEMICIRCLE37）长圆孔：LONG ROUND HOLE38）对开：OPPOSITE ORIENTED39）削薄过渡：TAPERED TRANSITION40）与封头内壁吻合：AS PER LOCATED INNER SUREFACE OF HEAD41）组焊后加工：MACHINED AFTER WELDING42）法兰密封面待组焊后加工：THE FLANGE SEAL SURFACE SHALL BE MECHINED AFTERWELDING43）安装就位后点焊：SPOT-WELDED AFTER INSTALLATION44）热处理后加工：MECHINED AFTER PWHT45）（由）制造厂（决定）最终尺寸：FINAL DIMENSION BY MANUFACTURER46）衬里和填充料重量：LINING AND FILLING WEIGHT47）修改版次：REVISION48）标记：MARKED49）管口标高、尺寸和等级：ELEVATION SIZE AND RATING OF NOZZLES8 技术要求及特性表中常用语1）FLUID (OR MEDIUM)：介质2）FLAMMABLE：易燃3）HAZARDOUS：危害性的4）TOXIC：毒性5）LETHAL：致死的6）SPEC. GRAV.：密度（填充物的）7）DEW POINT：露点8）DESIGN PRESSURE：设计压力9）DESIGN TEMPERATURE：设计温度10）OPERATING PRESSURE (TEMPERATURE)：操作压力（温度）11）MAX OPERATING PRESS & TEMPERATURE：最大操作压力（温度）12）JOINT EFFICENCY：焊接接头系数13）CORROSION ALLOWANCE：腐蚀裕度14）INSULATION THICKNESS (WARM/COLD/SOUND)：保温层厚度（暖、冷、声）15）ULTROSONIC EXAMINATION：超声波检测16）RADIOGRAPHIC EXAMINATION：射线检测17）HYDROSTATIC TEST：水压试验18）PHNEUMATIC TEST：气压试验19）LEAKAGE TEST：气密性试验20）KEROSENE LEAKAGE TEST：煤油渗透试验21）AMMONIA GAS LEAKAGE TEST：氨渗透试验22）HEAT TRANSFER AREA：换热面积23）TRIANGULAR PATTERN：三角形排列24）SQUARE PATTERN：正方形排列25）SAFETY VALVE SET PRESSURE：安全阀启跳压力26）RUPTURE DISK BURSTING PRESSURE：爆破膜爆破压力27）NET WEIGHT：净重N.W28）EMPTY WEIGHT：空重 E.W29）WEIGHT WITH WATER：充水重30）TOTAL WEIGHT：总重T.W31）VACUUM：真空32）FULL VACUUM：全真空F.V33）CAPACITY：容积34）MINIMUM DESIGN METAL TEMPERATURE：MDMT最低金属应力温度35）INTERGRANULAR CORROSION TEST：晶间腐蚀试验36）IMPACT TEST：冲击试验37）IMPACT SPECIMEN：冲击试样38）CHARPY IMPACT TEST：夏比冲击试验39）MINIMUM IMPACT ENERGY：最小冲击功40）V-NOTCH：V型切口9 常用技术要求的英文译法1）采用锻件按JB4726 II级为合格：FORGING MATERIAL SHOULD BE APPLIED AND INSPECTEDAS II OF JB4726 REQUIREMENTS2）焊接采用电焊，焊条牌号为×××：SMAW SHALL BE APPLIED, AND THE ELECTORDE TYPE IS×××3）补充技术要求：SUPPLEMENT TECHNICAL REQUIREMENTS4）未注明角焊缝焊角高度按较薄板厚度：UNLESS OTHERWISE SPECIFIED, THE FILLET WELD LEGSIZE SHALL BE EQUAL TO THE THICKNESS OF THETHINNER PLATE TO BE WELDED ON.5）板材以正火状态供货：THE STEEL PLATE (可填具体材料) SHALL BE SUPPLIED ASNORMALIZED CONDITION6）除图中注明外，焊接接头型式及尺寸按HG20583-1998中规定，法兰的焊接按相应法兰标准规定：UNLESS OTHERWISE SPECIFIED IN THIS HEREIN DWG, THEWELD TYPES AND DIMENSIONS SHALL BE AS PERSTIPULATED IN HG20583-1998, AND PIPE(OR NECK) TOFLANGE JOINTS AS PER RELEVANT FLANGE STANDARDSREGULATIONS7）未注圆角为Rx：UNLESS OTHERWISE SPECIFIED, THE ROUND RADIUS IS Rx 8）未注倒角为××：UNLESS OTHERWISE SPECIFIED, THE DIMENSION OFCHAMPER IS ××9）“A”与“B”配钻：“A”SHALL BE DRILLED WITH “B”TOGETHER10）“A”与“B”对中：SAME AXIES FOR “A”AND “B”11）含××半圆孔：××SEMICIRCLE HOLES COUNTED10 常用介质1）HYDROGEN：氢气2）OXYGEN：氧气3）NITROGEN：氮气4）CARBON OXIDE：一氧化碳5）CARBON DIOXIDE：二氧化碳6）HYDROGEN SULFIDE (H2S)：硫化氢7）AMMONIA (NH3)：氨8）METHANOL：甲醇9）INERT GAS：惰性气10）LPG(LIQUEFIED PETROLEUM GAS)：液化石油气11）SOUR GAS：酸性12）ALKALIZATION WATER(ALKALIZED WATER)脱盐水：13）SYNGAS (OR SYNTHESIS GAS)：合成气14）SHIFTED GAS：变换气15）RECYCLE GAS：循环气16）POLYMETER：聚合物17）DIESEL：柴油18）METHANE：甲烷19）RESIDUE OIL：渣油20）CRUDE OIL：原油11 其他1）LIST OF ATT. DOC. NO. ：附表号2）ORIENT. OF NOZ. DOC. NO. ：管口方位文件号3）PROJ. NO. ：项目号4）PROCESS DATA SHEET：工艺数据表5）PERSONNEL PROT：人员保护6）FIRE PROOFING：防火LAHH 高高液位报警口LAH 高液位报警口NLL 正常液位LAL 低液位报警LALL 低低液位报警。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
一、MATERIAL（材料）
英文
Electro-galvanized steel(SECC)
Cold roll steel(CRS) halfhard copper Silicon steel stainless steel metal alloy nickel plating degrease spray paint silk screen chroma rustiness grey dimension third angle projection size cross section front view oval hole insertion of bending part number lance form opposite side screw punch chamfer diameter width burr side corner biconvex radius an angle of ninety file screw rivet wiredrawing sample accompanied unless conform fine direction otherwise produce sharp opening
公差 单位 断面 俯视图 方孔 ban位 料厚 名称 反面 牙距 成型 攻牙 全圆角 高度 基准线 冲压方向 两面凹 圆弧 度 尺 圆头钉 螺栓 清洗 质量 检查 必须 展示 硬度 相同 细线 绘图 附带 不受影响
制表：高勇 2004-6-28
中文 铝片 青铜片 白铁 镀锌钢板 磷铜片 镀锡钢 防松螺母
英文 sus304csp-3/4h brass washer screwdriver screw tap calliper gange screw cap bright or dull tin plate silver anodizing fine brushed golden yellow to oxidize recommended hole size chrome tolerance unit section top view square hole half pierce(half biank) sheet thickness title inverse pitch form taping full R height datum line press direction biconcave/concave arc degrce square stud /tack bolt to erase mass inspection should show hardness as hairline drawing/plot accompanied free from
中文 不锈钢片 黄铜 垫圈 螺丝刀 螺丝攻 孔径规 螺帽
电光锡亚锡 氧化银白色 磨砂 金黄色 氧化 建议尺寸 铬
二、FINISH（表面处理） zinc plating 镀锌 black anodize 氧化黑色 sand blasting 喷砂 coating 涂层 electrolysis 电解 see note 注意看 grain direction 磨纹方向 三、SEE DRAWING（视图） 尺寸 angles 角度 第三角视图 scale 比例 规格 detail 祥图 剖面视图 left side view 左视图 主视图 hole 孔 椭圆孔 burring 猪嘴孔 脚仔 bending 折边 货号 revision/issue 版本 桥位 near 正面 相对面 thread 螺纹 螺钉 extrusion 挤形 冲裁 welding 焊接 斜角 radius 圆角 直径 length 长度 宽度 deep 深度 披风面 rolling(grain)direction 料纹方向 角 bend 弯曲 两面凸 point 点 半径 diameter 直径 90度角 base 底 挫 nail 钉 螺丝钉 nut 螺母 铆钉 staple U U型钉 拉丝 debugging 调试 样品 report 报告 附带 deliver 交付 除….之外 surface 表面 符合 grade 等级 优良 brush 轻擦 命令 cohversion 变换 别样的 further 进一步 制造 computer 计算器 锋利 deges 边界 孔、口 emboss/convex 凸形
中文 电解板 冷轧钢 红铜片/紫铜 矽钢 不锈钢 金属 合金 镀镍 除油 喷油 丝印 色/浓度 生锈 灰色
英文 aluminium(al) bronze sheet tin plate(马口铁） galvanized steel phosphors bronze sheet tinned strip steel locknut