产品规格书样本(DVD机芯)

VER：00SPECIFICATION产品规格书DESCRIPTION：DVD MECHA名称DVD机芯MODEL ：DV-36型号DV-36CUSTOMER ：客户CYSTINER AOORIVED客户承认Approved批准Checked确认Prepared制作-1-Table of Contents目录1．Scope (4)适用范围2．General Specification (4)一般规格2.1 Applicable Disc Format (4)支持碟片规格2.2Applicable Disc Capacity (4)支持碟片容量2.3Applicable Disc Diam eter (4)支持碟片直径2.4Op eration Environment (4)工作环境条件2.5Pick Up Moving Range (4)光头驱动方式2.6Feeding Ratio (4)光头移动量2.7Pick Up Moving Range (4)光头移动范围2.8Operation Environment (4)工作环境条件2.9Storage Environment (4)保存环境条件2.10Dimension (4)外形尺寸2.11Weight (4)重量3．Optic、Mechanical＆Electrical Specification (5)光学、机械及电气性能规格3.1Main parts (5)主要部品3.2Mechanical Specification (5)机械性能规格3.2.1Mechanical Noise (5)机械噪音3.2.2Spindle Motor (5)主轴马达3.2.3Tray in/out Motor (5)进给马达3.2.4Sled Motor............................................................ . (6)进出仓马达3.2.5Turn Table................................................................... . (6)转盘-2-4．Condition of performance Evaluation (6)性能评估条件4.1Install Angle (6)放置角度4.2Evaluation Environment (6)评价环境4.3Evaluation Disc (6)评价碟片4.4Evaluation Equipment (7)评价设备5．Reliability Tes t (7)可靠性保证5.1R eliability Specification (7)可靠性规格5.2High Temperature Operation Test (7)高温动作试验5.3Low Temperature Operation Test (7)低温动作试验…5.4High Temperature Storage Test (7)高温保存试验5.5Low Temperature Storage Test (7)低温保存试验5.6Constant Temperature and Humidity Test (8)恒定湿热试验5.7Swept Vibration Test (8)扫频振动试验5.8Impact Test (8)碰撞试验5.9Drop Test (8)跌落试验5.10Mechanical Life Test (9)机械寿命试验6．Sampling Examination (9)抽样检查7．Standard Quoted (9)引用标准8．Connector Description (9)端子说明9．Caution (9)使用注意事项10．Appendix (10)附录10.1Connector Description………………………………….……………..…..10/11端子说明：10.2Mechanical Dimensions (12)产品外形尺寸图-3-1．Scope适用范围1.1This specification to DVD Mecha for DVD player (model:KD-309).本规格书适用于DVD播放机用的DVD Mecha (型号:KD-309);1.2Any doubt to the specification can be resolved according to the agreement established withyour relevant department;对本规格书产生疑义时,可依据与贵司的有关部门达成的协议解决;1.3For improving performance purpose, this specification is subject to change according topre-agreement established between us;为了改善产品性能，本协议书的内容可以依据双方的事前协议进行变更；1.4Hardware and software or manufacturing process may subject to change for improvementswithin the range of the specifications;在满足本规格书的范围内，为改善产品性能可能会对硬件、软件或制造工艺进行变更；2．General Specifications一般规格2.1Disc Loading Mode 进碟模式,motor driver front loading tray 马达驱动方进仓2.2Disc fixing 碟片固定时Beam magnetic fixation 弱磁固定2.3Applicable Disk Diameter:支持碟片直径：12厘米，8厘米2.4Regulate mode：3points regulate调整方式：3点调整2.5Pick Up Driving Mode: Reduction Gear And Rack Drive光头驱动方式：减速齿轮和齿条驱动2.6Feeding Ration: 0.5mm/rpm (Sled Motor Rotation One Circle)光头移动量：0.5mm/rpm（进给马达旋转一周）2.7Pick Up Moving Range:22.6±0.3--59±0.4mm(Begin From Center Of Turn Table)光头移动范围：22.6±0.3--59±0.4mm 从转盘中心开始2.8Operation Environment工作环境条件Temperature温度0℃～45℃Humidity 湿度20%～80%RHAtmospheric pressure 大气压85～106KPa2.9Storage Environment：保存环境条件Temperature：温度-30℃～60℃Humidity：湿度5%～90%RHAtmospheric pressure：大气压85～106KPa、2.10Dimension:180 mm×133.8mm×29mm(L×W×H)外形尺寸：长180厘米，宽133.8厘米，高29厘米2.11Weight：approximately 260g重量约260克-4-3．Optic, Mechanica l＆Electric Specification光学、机械及电气性能规格3.1Main parts主要部品Spindle motor:主轴马达Manufacturers:盟升/三盛/万宝至等Sled motor:进给马达Manufacturers:盟升/三盛/万宝至等Tray in/out Motor进出仓马达Manufacturers:盟升/三盛/万宝至等Pick-up:光头Manufacturers: Samsung DL6FS/ Sanyo HD850/ Sony313等3.2Mechanism Specifications 机械性能规格3.2.1Mechanical Noise机械噪音Background noise is less then 25dB, measured at 100mm distance, mechanical noise：背境噪音小于为25dB，在100mm距离测量机械噪音Play 播放时50dB max3.2.2SPINDLE MOTOR主轴马达ITEM 项目SPEC 规格REMARKS备注RA TED VOLTAGE额定电压3V～DCVOLTAGE RANGE使用电压范围4.5～6.0V DCRA TED LOAO 额定负荷12cm normal loadRA TED SPEED 额定转速2500±400 rpm Min Rated Load Rated V oltageRA TED CURRENT额定电流105mA Max Rated Load Rated V oltageSTARTING TORQUE启动转矩1.323Mn,m Min Rated VoltageNO LOAD SPEED空载转速3500±450rpm No load Rated V oltageNO LOAD SPEED空载电流45 mA Max No load Rated V oltageSTARTING CURRENT启动电流450 mA Max Rated Voltage3.2.3SLED MOTOR进给马达ITEM 项目SPEC 规格REMARKS备注RA TED VOLTAGE额定电压2VVOLTAGE RANGE 0.5～6使用电压范围RA TED LOAO 额定负荷4g-cmRA TED SPEED 额定转速1600±200rpm Rated Load，3VRA TED CURRENT额定电流65mA以下Rated Load，3VSTARTING TORQUE启动力矩最小为14g 3VNO LOAD SPEED 无负荷转速2200±200rpm No Load，3VSTA TING CURRENT启动电流最大为245mA 3V-5-3.2.4TRAY IN/OUT MOTOR 进出仓马达ITEM 项目SPEC 规格REMARKS备注RA TED VOLTAGE额定电压2VVOLTAGE RANGE使用电压范围1～6RA TED LOAO 额定负荷4g-cmRA TED SPEED 额定转速1600±200rpm Rated Load，3VRA TED CURRENT额定电流65mA以下Rated Load，3VSTARTING TORQUE启动力矩最小为14g 3VNO LOAD SPEED 无负荷转速2200±200rpm No Load，3VSTA TING CURRENT启动电流最大为245mA 3V3.2.5TURN TABLE 转盘ITEM 项目SPEC 规格REMARKS备注TURN TABLE HIGHT 转盘高度8±0.15mmUP FACE OR CHASSISFOR DATUM LANE以CHASSIS的上表面为基准TURN TABLE TILT 转盘斜度MAX0.25°0.5°以下TURN TABLE RUNOUT 端面跳动MAX0.06mm 0.06mm以下ECCENTRICITY偏心MAX0.06mm 0.06mm以下AXIAL LOAD 耐压负荷MIN 49N（5Kg）49N（5Kg）以上BETWEEN TURN TABLEAND MOTOR SHAFT转盘与马达之间的耐压力SLIPPING TORQUR 打滑力距MIN1.96×10-2N.M(200gf.Cm)MIN1.96×10-2N.M(200gf.Cm)以上Disk Specification：Inner Diameter：Ф15.1mm 厚度：1.2mm4．Condition for performance Evaluation性能评价条件4.1Install Angle：Horizontal：±5°放置角度：水平：±5°4.2Evaluation Environment评价环境条件Temperature 温度18℃～22℃Humidity 湿度60%～70%RHAtmosphere pressure 大气压85～106Kpa4.3Evaluation disc评价碟片DVD：TDV-520A Manufacturers: ABEXC D：TCD-784 Manufacturers: ABEXFollowing condition can be adopted if there is no doubt in evaluation, use normal DVD and CDdisc:但是，如果判断不会产生异议，也可按下述条件，使用符合碟片规格要求之普通DVD及CD碟判断-6-Temperature 温度15℃～35℃Humidity 湿度45%～75%RHAtmosphere pressure 大气压85～106Kpa4.4Evaluation Equipment评价设备4.4.1JITTER Equipment JITTER仪TYPE型号：DVD MWJ-6391A，made by MEGURO ELECTRIC.CO.CD MJM-631C, made by MEGURO ELECTRIC.CO.4.4.2Mechanism And Circuit Equipment机械性能和电气性能评价设备Use MITKO Mechanism And Servo Circuit Equipment Or Use Equipment accordingTO pre-agreement established between us使用我司的机械性能和伺服电路评价设备或使用双方协定设备来评价5．Reliability Test 可靠性试验5.1 Reliability Specification 可靠性评价规格Reliability test specification follow 可靠性试验进行如下测试应满足规格要求：Item 项目Specification 规格y for disc as follow用如下碟片播放DVD：TDV-520（ABEX）CD：TCD-784（ABEX）Play for l Min, and no pause or interruption Of picture or sound播放1分钟，应无画面声音停顿、中断2.If there is no doubt in evaluation, play for usual DVD and CD disc as follow:如果判断不会产生异议，也可使用符合碟片规格要求如下普通DVD及CD碟片判断：MP3，VCD，DVCD，DVD9，DVD5，CD Play for l min, and no pause or interruption of picture or sound播放1分钟，应无画面声音停顿，中断Item 项目Specification 规格5.2 High Temperature Operation Test高温动作试验Naked sample is supposed to work normally for72hours under45±2℃,according to GB9384无包装样机按GB9384要求，样品在45±2℃环境下应能连续工作72H5.3 Low TemperatureOperation Test低温动作试验Naked sample is supposed to work normally for l hour, after having suffered from3℃～5℃for 2hour with no power on无包装样机，不通电，在3℃～5℃条件下放置2H，然后接通电源，应能连续正常工作1H5.4 High TemperatureStorage Test高温保存试验Naked sample with no power on is supposed to meet reliability specification form60±2℃for 2hourw,then cool down to normal atmosphere pressure for 16hours before starting test无包装样机，不通电，在60±2℃条件下放置2H，然后降至常温，恢复16H，进行测定，应满足可靠性规格要求5.5 Low TemperatureStorage Test低温保存试验Naked sample with no power is supposed to meet reliability specification in this case: suffered form-30±2℃ for 16hours,then heat up to normal atmosphere pressure for 2 hours before starting test无包装样机，不通电，在-30±2℃条件下放置2H，然后升至常温，恢复16H，进行测定，应满足可靠性规格要求-7-5.6 Constant Temperature and Humidity Test恒定湿热试验Naked sample with no power is supposed to meet reliability specification in this case; sufferedform40±2℃ for 4 hours then add moisture to (87%～92%relative humidity in 0.5hour,then cool down to normal atmosphere pressure, start test after4hours 无包装样机，不通电，在温度为40±2℃条件下，预处理4H，然后加湿，使之在87%～92%的相对湿度条件下放置48H，然后在0.5H内降至72%～78%，再降至常温，恢复4H后，进行测定，应满足可靠性规格要求5.7 Swept Vibrati on扫频振动试验Frequency频率范围（HZ）Amplitude位移幅值（mm）Sweeping times ateach axis每一轴线上的扫描循环次数Requirement要求10～20～300.75 5Do vibration test At X-Y-Zaxis orderly工作位置在三个互相垂直的轴线上依次振动30～50～300.15 5T-sweeping period(min),fl-the minimal frequency(Hz),f2-the maximal frequency(Hz)注：以loct/min的扫频带速度，在某一频率范围内进行一次循环扫频的时间为：T＝6.6441g（f2/f1），式中T—时间（min），f1—扫频下限频率（Hz），f2—扫频上限频率（Hz）应满足可靠性规格要求5.8 Impact Test碰撞试验Sample is supposed to meet reliability specification in this case: suffered from pulse peak acceleration—100m/s2,duration—16ms,duration—16ms、1000times Impact before starting test样品在经受了脉冲峰值加速度为100m/s2（10G）、持续时间为16ms、碰撞次数为1000次的碰撞试验后，进行测定，应满足可靠性规格要求5.9 Drop Test跌落试验Face Drop面跌落Edg e＆Corner Drop棱、角跌落Times跌落次数Height跌落高度Face跌落面Height跌落高度Edge跌落棱Corner跌落角600mm 450mm3 edges extendingfrom dropped comer跌落角的三棱边One corner orthe bottom样品正面下方的任一角Onceeach各一次Note: sequence of dropping follows 3-2-5-4-6order (top face no drop),(1＝top,2＝front, 3＝bottom,4＝back,5＝left,6＝right)跌落面按3-2-5-4-6的顺序进行（1面不跌落）（1-顶面，2-正面，3-底面，4-反面，5-左面，6-右面）包装按出货方式（100台/BOX），应满足可靠性规格要求。