室内加热器使用说明书
电加热器使用说明书
安装、使用产品前，请仔细阅读使用说明书RJD-25/1140(660)制氮装置用隔爆兼增安型电加热器使用说明书煤科集团研究院有限公司前言本说明书是使用说明书。
本说明书对于初次使用RJD-25/1140(660)型制氮装置用隔爆兼增安型电加热器的用户很有必要，对于具有使用经验的用户，也可使其进一步加深理解，这一点也是编者的宗旨。
希望用户仔细阅读本说明书，完全理解后在付诸实践。
另外，设备在正常运转开始后，设备操作员与维修人员须将此说明书就近保管好，以便需要时参阅。
本说明书的主要容包括RJD-25/1140(660)型制氮装置用隔爆兼增安型电加热器的结构特征与工作原理、技术特征、安装调试使用操作以及维护保养等容。
由于RJD-25/1140(660)型制氮装置用隔爆兼增安型电加热器的研究与改进在不断进行，因此本说明书的容有可能与购买产品的具体情况有不符之处，如对购买产品或本说明书有疑问，请与下述部门联系：TEL：-56626032警告！先启动制氮机，工作稳定后再启动电加热器1.概述1.1主要用途及使用围●该电加热器专门用于矿用井下移动式制氮装置的配套，安装在矿用井下移动式制氮装置。
用于井底车场、总进风巷和主要进风巷，翻车机硐室，采区进风巷。
●品种、规格●RJD-25/1140(660)1.2执行标准及特征1.2.1 型号的组成及其代表意义R J D -25/1140(660)电压等级额定功率制氮装置用隔爆兼增安加热器1.2.2 执行标准执行标准为Q/SMY2222-2015；GB3836-2010。
1.2.3防爆形式矿用隔爆型“ExdeⅠMb”。
1.3基本参数1.4使用环境条件●隔爆型电控制箱能够在下列环境条件下正常工作：➢环境温度：0～40℃；➢相对湿度：≤95％（25℃时）；1.5工作条件●电加热器应安置在矿用井下移动式制氮装置。
工作环境的有害气体、瓦斯、煤尘含量和通风量应符合《煤矿安全规程》的规定，具有完整的供电系统，●额定工作电压：1140／660V（AC）●额定的功率：25KW●额定的工作制：长期工作制●制氮机工作稳定后再启动电加热器！！！1.6安全●电加热器的维护和保养工作必须在断电的情况下才能进行。
加热器使用方法说明书
加热器使用方法说明书操作指南：加热器使用方法欢迎您购买并使用我们的加热器。
请您仔细阅读以下使用说明，以确保正确并安全地使用加热器。
第一步：准备工作1. 在使用加热器之前，请确保室内通风良好，以确保安全使用。
同时，需要确保电源电压符合加热器的工作要求。
2. 检查电源插座是否正常，不得使用破损或带有松动接触的插座。
第二步：安装加热器1. 将加热器放置在水平且稳定的表面上，远离易燃物和可燃物。
确保周围没有阻挡物，以免影响散热和正常工作。
2. 请勿堵塞或堆放物品在加热器周围，以保持其通风良好。
3. 将加热器的电源线插头插入电源插座，并确保插牢固。
第三步：使用加热器1. 打开加热器的电源开关，根据加热器面板上的操作按钮调整加热器的工作模式和温度。
您可以选择适合您需求的加热模式。
2. 在操作加热器时，请向下拉开门面板以便更好地操作加热器控制面板。
3.加热器配有安全温度控制装置，可以避免过热现象。
但为了安全起见，我们建议您不要将加热器使用时间过长，特别是在长时间离开室内的情况下。
4. 加热器温度可以通过控制面板上的温度按钮进行调节，根据您的需要提高或降低温度。
5. 当不使用加热器时，请及时关闭电源开关，并拔掉电源线插头，以确保安全。
第四步：加热器维护1. 加热器使用一段时间后，会有灰尘和杂物附着在加热器表面和过滤器上。
请定期使用干净的布或吸尘器清洁加热器表面和过滤器，以确保正常工作。
2. 请勿使用带有腐蚀性或破损的清洁剂清洁加热器，以免损坏加热器表面和内部零件。
3. 如发现加热器有故障或异常，请立即停止使用，拔掉电源插头，并联系专业人员进行检修。
第五步：安全注意事项1. 在加热器工作期间，请确保加热器周围没有易燃物或可燃物，如纸张、布料等。
同时，请不要在加热器上晾晒湿衣物。
2. 请勿将加热器放置在潮湿的环境中，以免影响加热器性能和安全。
3. 当加热器在工作时，请不要离开室内太远，以免发生意外。
尽量避免儿童或宠物接近加热器。
Warmax使用说明书
Word 文档产品使用说明书HE2000A/HM2000AHE2500A/HM2500AHE3000A/HM3000A尊敬的用户：感谢你选择了美国沃尔麦斯科技有限公司的产品。
请认真阅读并遵循本手册中的安装和维护说明。
你将在今后数年中享受美国沃尔麦斯科技有限公司的加热器产品所带来的舒适温暖。
本产品在中国大陆地区执行以下标准：GB4706.1-2005 家用和类似用途电器的安全通用要求GB4706.23-2007 家用和类似用途电器的安全室内加热器的特殊要求产品型号：室内加热器（对流式踢脚线型电加热器）HE2000A \ HE2500A \ HE3000AHM2000A \ HM2500A \ HM3000A欢迎来到warmax世界请仔细阅读本手册本手册包含正确安装、使用和操作的基本信息，在安装、操作或清洁加热器前，请仔细阅读本手册。
如果不按照本手册程序操作，将有可能导致火灾、触电或严重的人体伤害等。
妥善保管并经常阅读本手册将有助于安全正确使用该加热器。
注意事项：1. 为避免过热，禁止覆盖加热器。
2. 加热器不得直接置于电源插座下面。
3. 在正确的用电环境下使用。
（注：中国大陆地区额定电压为：220V~，50Hz）Word 文档4. 建议配备专用电源线路，由专业人员进行布线（针对2.5KW以上机型）。
5. 必须使用可靠接地的三孔固定插座。
（注：中国大陆地区需使用不小于10A(HM2000A/HE2000A),16A(HM2500A/HE2500A,HM3000A/HE3000A)的三孔扁头固定插座）6. 本机使用耐高温绝缘电源线，参数为：3x1.0mm2(HM2000A/HE2000A）,3x1.5mm2(HM2500A/HE2500A/HM3000A/HE3000A）。
7. 通电使用时，确保加热器直立放置，严禁倒置或平放使用。
.8. 禁止自行拆卸加热器，有问题时，请与本公司维修部门联系。
9. 当你外出或长时间不使用加热器时，请关掉加热器，并拔出电源插头。
加热器的说明书
加热器的说明书使用说明书一、产品介绍该加热器为家用电器，主要用于提供温暖和舒适的室内空间。
具有高效节能、安全可靠等特点，是您居家生活的理想选择。
二、安全须知1. 在使用加热器之前，请阅读本说明书并按照说明操作。
2. 避免将加热器放置在易燃材料旁边，确保周围环境无障碍，并与其他电器设备保持一定的安全距离。
3. 请勿将加热器放置在潮湿的地方，避免接触水分。
4. 长时间使用加热器时，请确保有适当的通风，以保证室内空气流通。
5. 当加热器运行时，避免触摸其表面，以免烫伤。
6. 使用加热器时请确保电源插座连接稳固，避免插孔松动等危险。
三、使用方法1. 将加热器放置在平稳的地面上，确保其稳定。
2. 将插头插入电源插座，并确保插头插入牢固。
3. 打开加热器的电源开关，此时加热器开始工作。
4. 使用加热器时可以根据需要调整加热器的温度或风量等档位，以满足个人需求。
5. 当不再需要加热器时，请确保将电源开关关闭，并拔下插头。
四、注意事项1. 使用过程中请勿将物品放置在加热器上，以免影响正常散热。
2. 使用过程中如发现异常，如异味、烟雾、异响等，请立即停用加热器，并与专业维修人员联系，切勿私自拆解或修复。
3. 定期清洁加热器，以保持其良好的使用状态。
4. 当长时间不使用加热器时，请拔下插头以节省能源。
五、维护保养1. 清洁加热器之前，请确保已断开电源并待其完全冷却。
2. 使用柔软的布擦拭加热器表面，避免使用化学溶剂或刺激性清洁剂。
3. 定期清理加热器的灰尘和杂物，以确保其正常散热。
4. 如遇故障，请勿私自修理，而是联系售后服务部门或专业维修人员进行维修。
六、产品规格名称：家用加热器型号：XXX额定电压：XXXV额定功率：XXXW产品尺寸：XXX毫米×XXX毫米×XXX毫米净重：XXX千克生产日期：XXXX年XX月XX日七、售后服务如有任何质量问题或使用上的困扰，请您在购买后第一时间与我们联系，我们将竭诚为您提供解决方案。
海尔电热器操作指南说明书
Unpacking1. Unpack all materials used to protect the heater inside of carton. Retain plastic caps attached to exposed fittings for use during storage.2. Remove heater, accessories and all hardware from carton.3. Inspect all items for damage that may have occurred during shipment.General Safety InformationMake sure you read and thoroughly understand these safety and operating instructions. Keep these instructions for future reference. They are your guides to safe and proper operation of this heater.Safety information appears throughout this manual. Pay close attention to them. Below are definitions for the safety information listed throughout this manual.Indicates an im m inen t lyhazardous situation which, if notavoided, WILL result in death or serious injury.Indicates a potentially hazardoussituation which, if not avoided, COULD result in death or serious injury.Indicates a potentially hazardoussitua t ion which, if not avoided, MAY result in minor or moderate injury.Consumer: Retain this manual for future reference.Dyna-Glo ®Delux Natural Gas Radiant HeatersPlease read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.DescriptionDyna-Glo Delux Models RA100NGDGD and RA250NGDGD heaters are 50,000 to 100,000 and 250,000 BTU/Hr construction heaters. These heaters use natural gas for combustion. They are primarily intended for temporary heating of well-ventilated buildings under construction, alteration or repair. These heaters should be utilized in sheltered, well-ventilated areas, but never in occupied dwellings.Ignitor SizeGapL x W x H (in.)RA100NGDGD 50,000 to 104 ft 3/hr (2.95 m 3/h) 8” W.C. 14” W.C.7.5” W.C. 0.19“ (4.8mm) 16.3 x 16.3 x 29.8 100,000(41.4 x 41.4 x 75.7 cm)RA250NGDGD 250,000 260 ft 3/h (7.36 m 3/h) 10 PSI 250 PSI6 PSI 0.19” (4.8 mm) 14.7 x 14.7 x 44.3 (37.3 x 37.3 x 112.5 cm)Fuel Type – Natural Gas Only Ignition Type – P iezo (RA100NGDGD)Minimum Operating Temp. – -20°F (-29°C)Pilot (RA250NGDGD)SpecificationsGHP Group, Inc.6440 W Howard St Niles, IL 60714ANS Z83.7-2011 CSA 2.14-2011 Construction HeaterC USC USFigure 1 – Models RA100NGDGD / RA250NGDGDGeneral Safety Informationconstruction heater in accordance with ANS Z83.7 CSA 2.14. Other standards govern the use of fuel gases and heating products for specific uses. Your local authority can inform you of these. The primary purpose of these construction heaters are to provide temporaryheating of building under construction, alteration, or repair. When properlyused, the heater provides safe economical heating. Products of combustion are vented into the heated area.- For either indoor or outdoor use. Adequate ventilation must be provided.IMPORTANT: Every possible circum-stance that might involve a hazard can-not be anticipated. The warnings in this manual on tags or decals affixed to the unit are not all inclusive. If a procedure,work method, or operating technique not specifically recommended by Day-ton is used, you must make sure it is safe for you and others. You should also ensure that equipment will not be dam-aged or be made unsafe by the operat-ing or maintenance method you use.death! Some people are more affected by Carbon Monoxide than others. Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, and/or nausea. If you have these signs, theheater may not be operating properly or the area may not be sufficientlyventilated. Get fresh air at once! Have heater serviced.Carefully install and always use great carewhen operating this heater. Be sure to research and follow all local ordinances and codes. In the absence of local codes, with the Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 and the Natural Gas and Propane Installation Code CSA B149.1.Natural Gas: Natural gas has a very distinctive odor that will help you detect a leak. However, this odor may fade in time. Natural gas may be present in the area even though no odor is detected.– U se only natural gas. Do not attempt to use propane gas. Use only factory preset regulator provided on heater.– P rovide adequate ventilation. Before using heater, provide at least a 3square foot (.28 m 2) opening of fresh, outside air for every 100,000 BTU/Hr rating.CaliforniaProposition 65Warning: Fuels used in gas or oil fired appliances and the products of combustion of such fuels, contain chemicals known to the State ofCalifornia to cause cancer, birth defects or other reproductive harm. This product contains chemicals, including lead and lead compounds, known to the state ofCalifornia to cause cancer, birth defects or other reproductive harm. Wash hands after handling.– T his heater should be utilized in sheltered, well-ventilated areas, but never in occupied dwellings.– D o not use heater in occupieddwellings, in living or sleeping areas.– K eep appliance clear and free from combustible materials, gasoline, paint thinner, and other flammable vapors and liquids. Dust is combustible. Do not use heaters in areas with high dust content.– C heck heater for damage before each use. Do not use damaged heater.®Radiant HeatersGeneral Safety Information (Continued)Minimum heater clearance from combustibles:Sides: 6 feet (1.8 m) Top: 5 feet (1.5 m)Floor: Combustible - Not for use on finished floors– T he heater, other than a heater with integral propane gas container, must be located at least 6 feet (1.8 m) (in Canada, distance must be 10 feet [3 m]) from any propane gas container.– B lower or radiant type heaters shall not be directed toward any propane gas container within 20 feet (6 m).– C heck hose before each use of heater. Do not use if hose is cut or damaged. Replace with hose specified by manufacturer.– A lways be sure to place the heater onheater is in operation.– T damage may occur.– P water or rain.– K from the heater.– N – A lways wear gloves when handling the heater to prevent injury.– N ever attach ductwork to heater.– D o not alter heater. Keep heater in its original state.– D o not use heater if altered.– T urn off gas supply to heater whennot in use.– U se only original replacement parts.This heater must use design specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injury.AssemblyMODEL RA100NGDGD1. Provide natural gas supply system.2. Install plumbing to a low pressure natural gas source to heater. The source must be regulated to 1/2 PSI, maximum 3/4’’ (19 mm) I.D. pipe or flexible connector, not longer than 10 feet (3 m).3. Be sure to use thread sealingcompound when connecting the hose to the heater at the 1/2’’ (13 mm) NPT fitting at the regulator inlet. Tighten all fittings with a wrench.4. Open natural gas supply valve Never use an open flame to check for aleak. Apply 50/50 mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.6. Close natural gas supply valve.MODEL RA250NGDGD1. Insert AA battery (included) into ignition by turning COUNTERCLOCKWISE and unscrewing ignition cap.2. Provide natural gas supply system.3. Install plumbing to a natural gas source to heater.4. Connect gas supply to heater using minimum 3/8” (10 mm) ID pipe.Maximum pipe length is 10 feet (3 m).5. Connect hose or plumbing to 1/2” (13 mm) NPT flare fitting at thevalve inlet. Tighten all fittings with a wrench.6. Open natural gas supply valveSLOWLY. Check all connections for leaks. Never use an open flame to check for leaks.7. Close natural gas supply valve. NOTE: Keep hands and face away from outlet (around top of shelf) of heater while attempting to start heater.Models RA100NGDGD and RA250NGDGDDyna-Glo Delux Operating Instructions and Parts ManualFigure 3 – Heater Control Knob –RA100NGDGDHot while inoperation. Do nottouch. Keep children, clothing, furniture,gasoline, and other liquids havingflammable vapors away.The gas supply attaches to the heaterby a minimum 3/8’’ (10 mm) I.D. pipeor flexible connector. User must supplypipe or flexible connector. The lengthshould be no more than 10 feet (3 m).The natural gas moves through the2. Always be sure to place the heater ona stable and level surface while theheater is in operation. Be sure that nostrong winds blow into the ends ofthe heater.to OFF position.4. Turn natural gas supply valve on.5. Depress heater control knob andturn counterclockwise to (IGN) LOWTO SHUT DOWN HEATER1. Shut off the main burner valve, beingsure to wear a glove for protection.Turn the control knob to the OFFposition.2. Firmly close the natural gas supplyvalve.TO RESTART HEATER1. Wait five minutes for heater to cool.2. Follow steps in TO START HEATERsection.TO START HEATER (RA250NGDGD)1. Follow all of the safety, ventilationand installation instructionspreviously noted in this manual.2. Always be sure to place the heater ona stable and level surface while theheater is in operation. Be sure that nostrong winds blow into the ends ofthe heater.3. SLOWLY open the gas valve.4. Push in and hold safety valve buttonwhile pushing ignitor button untilpilot lights (see Figure 4).NOTE: Hose may be filled with air, ifso, allow around 15 seconds for gas toreach pilot.5. If pilot does not light, repeat Step 4.6. When pilot stays lit, fully open themain burner valve by turning thehandle of the burner valve counter-clockwise until it stops all the way tothe ON position.®Radiant HeatersFigure 4 – RA250NGDGD Part IdentificationOperation (Continued) NOTE: Arrows on main burner valve handle show directions for ON and OFF.TO SHUT DOWN HEATER1. Firmly close the natural gas supply valve.2. Shut off the main burner valve, being sure to wear a glove for protection.the way to the OFF position.TO RESTART HEATER1. Wait five minutes for heater to cool.2. Follow steps in TO START HEATERsection.Running heaterbelow specified gaspressure may cause flashback. Duringflashback, the burner flame is mostlyyellow. The flame will burn inside theburner tube causing a roaring noise. Ifflashback occurs, turn heater off. Afterburner tube cools off, restart heater.NATURAL GAS SUPPLYYou must provide the natural gas supplyalong with all pipe and fittings.Check with your local gas supplier toproperly size all of your supply lines. Besure to follow all local codes, or refer tothe Natural Fuel Gas Code Handbook –NFPA54/ANSI Z223.1, or the Natural GasInstallation Code – CAN/CSA B149.1.VENTILATIONA three square footopening of freshoutside air for each 100,000 BTU/Hr ofheater output must be provided tooperate each heater safely. If the properventilation air is not provided, carbonmonoxide poisoning can occur.Always be sure that the properventilation is being provided beforestarting this heater.FRESH OUTSIDE AIR OPENINGREQUIREMENTSHeater size Opening100,000 BTU 3.0 ft2 (.28 m2)250,000 BTU 7.5 ft2 (.70 m2)Read and understandall of the warnings inthe General Safety Information pages of thismanual. They are essential to the safeoperation of this heater. Be sure to followall local codes when operating this heater.Be sure to leak test allfittings and pipeconnections after installation or repairs. Usea 50/50 mixture of liquid dish soap andwater. Bubbles forming reveal a leak. Youmust repair all leaks at once!Models RA100NGDGD and RA250NGDGD Dyna-Glo Delux Operating Instructions and Parts ManualFigure 5 – RA100NGDGD Part IdentificationKnobNever attempt toservice heater whileit is connected to natural gas supply,operating, or hot. Severe burns can occur.1. Always keep heater clean.2. Inspect heater before each use.Check connections for leaks. Applya 50/50 solution of dish soap andwater. Bubbles forming show a leakthat must be corrected. Correct leaksat once.3. Inspect regulator hose assemblybefore each use. If hose is highlyworn or cut, replace with hosespecified by manufacturer.4. Keep appliance area clear and freefrom combustible materials, gasoline,and other flammable vapors andliquids.5. Have heater inspected yearly by aqualified service person.6. The flow of combustion andventilation air cannot be obstructed.STORAGEDisconnect heaterfrom natural gassupply.1. Place plastic cover over brass fittingon inlet connector.2. Store in a dry, clean, safe place.3. When taking the heater out ofstorage, always check inside theheater. Small animals or insects mayplace foreign objects in the heater.Keep heater free from foreign objectsand combustible materials.®Radiant HeatersSymptom Possible Cause(s) Corrective ActionBurner fails to lightBurner lights but goes outwhen automatic controlvalve button is releasedBurn rate is low, emitterdoes not glowFlames are extremely highand coming from emitter1. More warm-up time needed2. Gas pressure is low3. Thermocouple loose or in need ofreplacement4. Automatic control valve in need ofreplacement1. Main burner valve not completely open2. Clogged gas orifice3. Low gas pressure4. Low gas supply1. Main burner valve not fully open2. Plugged gas orifices3. Low gas pressure4. Low fuel supplyUnit has been connected to a propane gassupply instead of natural gas1. Relight, holding control valve button in for45 seconds2. Inspect natural gas supply3. Tighten, reconnect or replacethermocouple4. Replace automatic control valve1. Completely open main burner valve byturning control knob to HIGH position2. Replace gas orifice3. Check gas supply, regulator function4. Contact gas supplier1. Fully open main burner valve by turningcontrol knob towards HIGH position until itstops2. Replace gas orifice3. Check gas supply, regulator output4. Consult gas supplierCheck gas source and replace with natural gassupplyTroubleshooting ChartFor Repair Parts, call 1-877-447-4768 Please provide following information:-Model number-Serial number (if any)-Part description and number as shown in parts list ArrayFigure 6 – Repair Parts Illustration for Natural Gas Radiant Heater RA100NGDGDModel RA100NGDGDDyna-Glo Delux Operating Instructions and Parts ManualRepair Parts List for Natural Gas Radiant Heater RA100NGDGD1 Top Cover 5002854 12 Guard 2315528 13 Emitter 2315519 14 N ozzle2315521 1 5 Nozzle Connector 2315545 1 6 Nozzle Nut2315546 1 7 Main Gas Tubing Assy (NG) 2315523 1 8 Nozzle Bracket 2315517 1 9 Flame Shield 2315516 2 10 Thermocouple 2201584 1 11 Spark Plug2201583 1 12 Thermocouple Holder 2315520 1 13 Base5002851 1 14 Control Knob 2101451 1 15 Control Valve GS22 (8B) 1 16 Fitting2304948 2 17 Tubing Inlet Assy2315524 1 18 Fitting-Regulator to Tubing Inlet 2315547 1 19 Regulator2315555 1 20 Regulator Bracket 2315518 1ReferenceNumber DescriptionRA100NGDGDQuantityHeater must use designspecific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.Figure 7 – Repair Parts Illustration for Natural Gas Radiant Heater RA250NGDGDFor Repair Parts, call 1-877-447-4768Please provide following information:-Model numberModel RA250NGDGDDyna-Glo Delux Operating Instructions and Parts ManualRepair Parts List for Natural Gas Radiant Heater RA250NGDGD1 Top Cover 5002854 12 Guard 2315554 13 Emitter 2315537 14 Upper Base 5002853 15 Base Cover 2315532 16 Lead Wire 2315643 17 Tilt Switch 2300186 18 Lower Base 5002852 19 Blanket 2315539 1 10 Insulation 2315544 1 11 Flame Shield 2315540 1 12 Thermocouple 2201591 1 13 Spark Plug2201583 1 14 Spark Plug Bracket 2315609 1 15 Bracket2315520 1 16 Box for Lead Wire 2315535 1 17 Pilot Assy GL250.39 1 18 Pilot Bracket 2315608 1 19 Wind Box 2315610 1 20 Ignition Wire 2201585 1 21 Battery 2300481 1 22 Ignition 2201220 1 23 Regulator2315513 1 24 Regulator Holder 2315536 1 25 Regulator Connector 2315547 1 26 Inlet Tubing Assy 2315542 1 27 Connector 2315549 1 28 Control ValveGS16 1 29 Contol Valve Fixing Nut 2305687 1 30 Contol Valve Bracket 2315538 1 31 Ball ValveGQ01 1 32 Ball Valve Connector 2305391 1 33 Pilot Connector 2315548 1 34 Main Tubing Assy 2315550 1 35 Pilot Tubing 2001402 1 36 Base Shield2315541 1 37 Rubber Ring for Wire 2315543 1 38 Nozzle Bracket 2315533 1 39 Nut2101008 1 40 Nozzle Connector 2315534 1 41 Nozzle 2315546 1Reference Number DescriptionRA250NGDGDQuantityHeater must use designspecific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.WarrantyRA100NGDGD and RA250NGDGD Dyna-Glo Delux Operating Instructions and Parts ManualLIMITED WARRANTY:This limited warranty is extended to the original retail purchaser of this Forced Air/Convection/Radiant Heater and warrants against anydefect in materials and workmanship for a period of one (1) year from the date of retail sale. GHP Group, Inc., at it’s option, will eitherprovide replacement parts or replace or repair the unit, when properly returned to the retailer where purchased or one of our service centersas directed by GHP Group, Inc., within one (1) year of retail purchase. (Shipping costs, labour costs, etc. are the responsibility of the purchaser.)DUTIES OF THE OWNER:This heating appliance must be operated in accordance with the written instructions furnished with this heater.This warranty shall not excusethe owner from properly maintaining this heater in accordance with the written instructions furnished with this heater.A bill of sale,canceledcheck or payment record must be kept to verify purchase date and establish warranty period.Original carton should be kept in case of warrantyreturn of unit.WHAT IS NOT COVERED:1.Damage resulting from use of improper fuel.2.Damage caused by misuse or use contrary to the owners manual and safety guidelines.3.Damage caused by a lack of normal maintenance.4.Fusese of non-standard parts or accessories.6.Damage caused in transit.Freight charges on warranty parts or heaters to and from the factory shall be the responsibility of the owner.This warranty does not imply or assume any responsibility for consequential damages that may result from the use,misuse,or the lack ofroutine maintenance of this heating appliance.A cleaning fee and the cost of parts may be charged for appliance failures resulting from lack ofmaintenance.This warranty does not cover claims which do not involve defective workmanship or materials.FAILURE TO PERFORMGENERAL MAINTENANCE(INCLUDING CLEANING)WILL VOID THIS WARRANTY.THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES,EXPRESSED OR IMPLIED,INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE.THEREMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF ALL OTHER REMEDIES.IN NO EVENT WILLGHP GROUP, INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.Some states do not allow limitations on how long an implied warranty lasts,so the above limitation may not apply to you.Some states do notallow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.CLAIMS HANDLED AS FOLLOWS:1.Contact your retailer and explain the problem.2.If the retailer is unable to resolve the problem,contact ourCustomer Service Dept.detailing the heater model,the problem,and proofof date of purchase.3.A representative will contact you.DO NOT RETURN THE HEATER TO GHP GROUP,INC.unless instructed by our Representative.This warranty gives you specific legal rights and you may also have other rights which vary from state to state.TO REGISTER THE WARRANTY ON YOUR HEATER,PLEASE FILL OUT THIS CARD COMPLETELYAND MAIL WITHIN14DAYS FROM DATE OF PURCHASE OR REGISTER ON-LINE AT NAME:______________________________________PHONE:()__________________EMAIL:____________________________ADDRESS:_________________________________CITY:______________________________STATE:__________ZIP:____________MODEL:____________________SERIAL#:_______________________________________DATE PURCHASED:__________________DEALER PURCHASED FROM:____________________________________________TYPE OF STORE:__________________________CITY&STATE WHERE PURCHASED:______________________________________________PRICE PAID:_______________________Please Take a Minute To Give Us Your Answers To The Following Questions.All Responses Are Used Solely For Market Research And Are Held In Strict Confidence.Who primarily decided this purchase?Male Female18-2425-3940-5960and overPurpose of Purchase?_______________________________________________________________________________________________Do you own any other portable heaters?Yes No If yes,type____________________________brand_____________________How do you intend to use your new heater?Construction Site Farm Warehouse/Commercial Garage/Outbuilding OtherHow did you become aware of this heater?In-Store Display Newspaper Ad Magazine Ad Friend/RelativeTV Commercial Store Salesperson Other___________________________What made you select this heater?Style Size/Portability Price Package Brand Other___________________Do you:own rent Would you recommend this heater to a friend?Yes NoPlease give us your comments:________________________________________________________________________________________THANK YOU FOR COMPLETING THIS FORM!Information will be held confidential.WARRANTY REGISTRATIONIMPORTANT:We urge you to fill out your warranty registration card within fourteen (14)days of date of purchase.You can also register your warranty on the internet atplete the entire serial number.Retain this portion of the card for your records.SAVE THIS CARD!Place Postage Stamp Here Tel: (877) GHP Group, Inc.6440 W Howard St Niles, IL 60714-3302GHP Group, Inc.6440 W Howard StNiles, IL 60714-3302。
加热棒使用说明范文
加热棒使用说明范文使用前的准备工作在使用加热棒之前，首先需要进行一些准备工作，以确保安全和有效地进行加热操作。
具体的准备工作包括：1.检查加热棒的外观是否完好，电源线是否有损坏，加热元件是否正常工作。
如果发现任何异常情况，应停止使用并及时维修或更换。
2.检查加热棒的工作电压和额定功率是否符合使用要求，确保所连接的电源符合加热棒的额定电压和功率要求。
3.准备好所需要加热的物质，并将其放置于适合的容器中，确保容器具有耐热性和耐腐蚀性，以免受到加热棒的影响而发生损坏。
4.确保所使用的加热棒在安全位置，避免碰触易燃物品和液体，以免引起事故。
使用步骤在做好准备工作之后，可以按照以下步骤正确地使用加热棒：1.将加热棒插入电源插座，并打开电源开关，确保加热元件正常工作。
注意：在使用加热棒时，应保持室内通风良好，避免因燃烧产生的有害气体对人体造成危害。
2.将要加热的物质放置在加热棒的加热区域内，并确保物质均匀地分布在加热棒周围，避免发生局部高温区域。
3.监控加热过程，确保加热过程中物质不会溢出或产生异常情况。
同时要随时注意加热棒的温度，避免过热导致事故发生。
4.在加热过程中，不能将手触摸加热棒和加热过的容器，以免发生烫伤。
同时要保持加热棒周围的环境整洁，避免发生火灾等安全事故。
5.加热完成后，要及时关闭电源开关，等待加热棒冷却后再进行清洁和维护操作。
注意：在清洁和维护加热棒时，必须先将电源拔掉，防止触电事故发生。
维护保养为了延长加热棒的使用寿命和保证其正常工作，需要进行定期的维护保养工作。
具体的维护保养方法包括：1.定期清洁加热棒的外表面和加热元件，以保持其良好的散热效果和加热性能。
2.注意保持加热棒周围的环境整洁，避免积尘和杂物对加热棒的影响。
3.定期检查加热棒的工作状态和连接线路是否正常，发现问题及时维修或更换。
4.不要在加热棒工作时离开现场，避免因意外情况导致事故发生。
总结加热棒是一种常用的加热设备，适用于实验室、工厂和家庭等多种场合。
恒温加热器使用说明书
恒温加热器使用说明书一、产品介绍恒温加热器是一种用于控制温度的设备，适用于实验室、工业生产等领域。
本产品采用先进的温度传感器和控制技术，能够实现精确的温度控制，具有稳定性好、操作简单等特点。
二、安全注意事项1. 本产品需在干燥、通风良好的环境下使用。
2. 请确保电源连接正确，接地可靠，以确保使用安全。
3. 仔细阅读产品说明书，并按照说明进行正确操作，避免不必要的事故发生。
4. 使用过程中应避免遮挡散热孔，避免过载使用。
5. 使用结束后，请拔掉电源插头，确保设备断电。
三、产品特点1. 温控范围广：本产品的温控范围可根据需要进行调整，满足不同的实验需求。
2. 温度稳定性好：经过精确的温度控制算法设计，保证设备稳定运行，提供精确的温度控制。
3. 操作简单：本产品采用触摸屏设计，界面简洁清晰，操作便捷，即使对设备不熟悉的用户也能够轻松上手使用。
4. 故障自诊断：设备具有故障自诊断功能，一旦出现故障，会自动报警并显示故障原因，方便用户快速排除故障。
四、使用方法1. 打开设备：接通电源后，按下电源按钮，待设备开机完成后进入待机状态。
2. 设置温度：通过触摸屏上的温度调节按钮，可自定义所需温度。
设定后，系统会根据设定值进行温度控制。
3. 启动加热：设定好温度后，点击启动加热按钮，设备将开始加热，并根据设定温度进行温度调节。
4. 监控温度：设备运行时，观察触摸屏上显示的实时温度值，确保温度始终在设定范围内。
5. 结束使用：使用完毕后，点击停止加热按钮，设备会停止加热并保持待机状态。
拔掉电源插头，确保设备断电。
五、故障排除1. 故障自诊断：设备出现故障时，会自动报警并显示故障原因，用户可根据报警信息进行故障排除。
2. 联系售后服务：若设备故障无法解决，请联系售后服务中心进行维修或更换。
六、维护保养1. 定期清洁：使用过程中请保持设备干燥，避免积尘。
定期用软布擦拭设备外壳，以保持清洁。
2. 防止碰撞：使用过程中请避免撞击设备，以免损坏设备外壳或内部元件。
飞利浦 3000i系列 室内加热器(对流式电暖器) 使用手册说明书
前壳 散热口
控制面板
后壳 烘衣架
脚板
电源开关 脚轮
2 技术参数
型号
AHR3142CS
额定电源
220V~ 50Hz
额定功率
2000W
防水等级 备注
IPX2 电子式(WIFI款)
本产品已通过3C认证
本产品根据国标：GB4706.1 GB4706.23 制造
3 装箱单
名称 对流式电暖器 遥控器 说明书 脚板 脚轮 壁挂挂钩 膨胀螺钉 壁挂螺钉 脚板螺钉
用。
现象。
• 取暖器在工作时严禁触摸防护网罩， • 本加热器的安装要使得在浴缸内或
防止高温烫伤；请特别注意儿童。
ቤተ መጻሕፍቲ ባይዱ
淋浴区的人不能够触及到开关和其
• 为延长产品使用寿命，请不要在取
他控制器。
暖时移动取暖器。
• 因为加热器被覆盖或不正确的放置 会引起火灾，故不得利用带有可自
禁止覆盖
动接通电源的程序器，定时器或任 警告：为避免过热，禁止覆盖加热器。 何其他装置来使用本加热器。
“中档”控制面板显示2d，按第
三次为“高档”控制面板显示3d， 遥控器使用方法
本机设有三个加热档位，依次循 打开遥控器背部电池盖装上两节 7号电池，
环。
即可使用；遥控器上按“ ”键，加热档位
4. 按“ ”键本机可在1h-12h内 递减一档，按“ ”键，加热
自由定时，每按一次递增1小时， 在显示屏上均有相应的显示，当 控制面板上显示为“ ”时说 明本机连续工作。
固定牢固。
注：壁挂安装时机体不能装上脚；
安装高度最低不能低于150mm。
2
7 使用方法
使用环境温度；也可控制加热器 是否工作；例：按“ ”键将温
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
产品介绍
1.塔是外观设计；时尚豪华；
2.优质PTC陶瓷发热体，热高效，更可靠；
3.智能8小时定时；
4.自动温控，过热保护；
5.90度旋转，广角送暖；
6.远距离遥控，方便舒心；
7.三档选着，满足不同需求；
8.倾倒自动断电，安全可靠。
型号规格
使用方法
1.将本产品电源插头插入220V～50Hz,10A的电源插座中
2.使用前，请先打开“手动电源开关”，此时开关指示灯
亮，机体处于待机状态。
3.开关：在待机状态下，按下控制面板“⊙”，或遥控上
的开/关键，此时本机吹出凉风，再次按下此键，本机
进度待机状态。
档位选择:在工作状态下，按下控制面板“●
摇头：在工作状态下，按下控制面板“□”或遥控器上的摇头开关，可进行90°范围左右摇头；
温度设定：按下控制面板“－或+ ”或遥控器上的摇头开关，可以设定10-49℃范围温度调节，当室温达到所设定的温度时，本机自动停止工作，当室温降到设定温度以下时，本机自动启动工作；
时间设定：按下控制面板“○”或遥控器上的时间设定键，可以将工作时间设定在1-8小时，达到设定时间后，本机自动进入待机状态。
4.需要关闭本机请按下控制面板“⊙”或遥控器上的开/关键，此时工作指示灯闪烁，本机自动保持冷风状态30秒，以确保机器内余热散尽，保护内部元器件。
注意事项
1.在本机没有组装好请不要接通电源，以免发生危险。
2.本机只适合在室内使用，严禁在室外使用。
3.本机不得直接安放在电源插座下面使用，使用前须先检查所用的电源是否与本机铭牌上的标示相符，电源线以及插头是否破损。
电源线请勿曲折、拉扯。
电源线为专用电源线，请勿随意更换。
4.请单独使用额定电压10A以上的插座，并有良好接地
措施。
请确保电源插座与插头接触良好，切不可任意调换插头接地片：若动作30分钟后插头烫手(约超过50℃)，请更换插座，以免发生危险。
避免与其它大功率电器共用插座。
5.禁止在存放有易燃、易爆等物品的场所以及浴缸、淋浴间等有水淋的场所使用或储藏，以免发生火灾、触电等安全事故。
禁止在长期潮湿、灰尘多的地方、有油烟的厨房等场所使用或储藏，以免发生漏电、火灾等事故。
6.严禁在有大量灰尘、粉尘的环境下使用。
室内无人应关闭电源。
7.本产品不适用与肢体、感官或智力上有缺陷的人士或缺乏经验和常识的人士使用，除非有他人能确保安全，对其进行监督，并提前阅读使用方法。
8.首次使用会有少量白烟和异味出现，属于正常现象。
9.使用本产品时勿让儿童靠近，以免发生危险。
10.请勿将本产品放在窗帘及室内家具旁边使用，放置时应离墙及家具50厘米以上，严禁在本产品上烘烤物品。
11.为免造成高温过热，禁止在机体上覆盖任何物体。
12.使用完毕后，先关闭电源键，在拔下电源插头，禁止用插拔电源线插头的方式代替本机的开机和关机功能。
13.本产品的覆盖或不正确放置会引起火灾，严禁利用带有自动接通电源的程序或其他装置来使用本产品。
14.拔出插头前先关掉电源，勿用湿手插拔电源插头，以免发生触电。
15.如电源线损坏，为避免危险，必须有制造厂或其他维修部门相关人员来更换。
16.禁止在工作时以电源线牵引机体。
17.禁止将本机放在水中清洗；禁止在浴缸、喷头、游泳池四周使用；请勿喷射挥发剂、杀虫剂等，可能造成机体外壳变质破损而造成的感电、漏电危险。
18.使用时绝对禁止插入异物或用手触摸出风口及周围的机体，以免发生烫伤等危险事故。
19.开启电源20秒内发出轻微通电声属正常，请继续使用。
20.严禁拆机，不得对本机进行任何形式的改造，以免发生危险。
21.外出或长期不用时，请关闭产品开关，并将电源插头从插座拔出。
22.如产品出现故障，请联系松桥当地的售后服务中心，切勿擅自拆机维修。
清洁与保养
1.长期不用时，请将本产品清洁干净，待其干燥后，
按原包装顺序将本机体及各部门件装入包装盒，置于干燥处妥善保管。
2.清洁前，请切断电源，带机体完全冷却后方可进行。
3.切忌直接用水或放入水中清洗产品，可用干净的软布进行擦拭，请勿使用汽油、甲苯等溶剂清洗。
4.清洁后，带机体充分干燥后方可通电使用。