锂离子电池专业英语
锂离子电池专业术语中英文对照
锂离子电池专业术语中英文对照1.Foil Creak-铝箔破裂2.Foil sealant delaminated-铝箔封口开口（分层）3.Broken tab-极耳折断4.Crease-折痕/起皱5.Pinhole-针孔/小孔6.swelling-气涨/肿胀7.Electrolyte Leakage-电解液漏出8.Surface contamination-表面脏污9.Foil Dent(Dot)-凹点10.Foil Dent(Line)凹痕11.Foil Protrusion(Dot)-凸点12.Foil Protrusion(Line)-凸起13.Scratch(indented Line)-划痕，划伤14.Flatness-平整度NG15.Barcode Defect-条码缺陷16.Barcode Skewed-条码歪斜17.Artwork Fuzzy-丝印模糊18.Stray Marks-少点19.Exposed Metal-露金属20.Deformation-变形21.Tab Deformation-极耳变形22.Tab Lift-off-极耳翘起，脱离23.Tab Overhang-极耳凸起24.Void Deformation-凹痕形变25.Discoloration-变色/脱色26.Uneven surface-表面不平整27.Cell Corner Protrusion-电芯边角变形28.Tape Protrusion pattern-凸痕(电芯因为电极卷绕，绝缘胶胶纸引起的电芯表皮凸痕)29.Fingerprint-指纹30.Pack surface Wrinkle After Carrier Removed-Regular pouch-夹具下料后，成品表面起皱bel wrinkle/Overlap/Peel-商标起皱/重叠/脱离bel Shine Mark-商标发亮33.Excess Glue-溢胶34.Glue Mark(Dont)-胶痕35.Glue Mark(Line)-胶痕36.Side Fold Peel-off-侧边张开37.Gap&Glue Line Integrity-胶水缺失间隔bel Creak-商标破裂39.VHB Liner Bubbles-气泡40.BMU Insulator Peel-BMU绝缘胶脱离41.Plastic Frame Damage-塑料壳损伤42.Positioning Hole Solder-定位孔焊锡43.Stiffener Shift-端子背面钢片超出FPC边缘44.Stiffener Hole Tangent to FPC Hole45.FPC Copper Exposure-软板漏铜46.FPC Dent/Protruding-软板凹痕/凸起47.FPC Creak/Tear-软板开裂/撕裂48.Burr on FPC-软板毛刺49.FPC Cover-lay Peel-off-软板外层脱离50.FPC Discoloration-软板脱色变色51.Glue Overflow-胶水溢出52.Foreign Material on FPC Surface-软板表面有异物53.Bubble on FPC surface-软板表面有气泡54.FPC surface contamination-软板表面有脏污55.Wrinkle Line on FPC Surface-软板表面有折痕56.Scratch Feel-划伤(接触)57.Connector Burr-端子毛刺58.Connector Oxidation-端子氧化59.Connector Body Deformed-端子实体变形60.Connector Contacts Deformed-端子连接金属变形61.Connector Housing Dents/Scratches-连接器外壳凹痕/划伤62.Connector Solder wicking-连接器金属粘锡63.Connector Pin Solder-连接器管脚脱锡64.Connector Tilt-连接器翘起/倾斜65.FPC Marking-软板标记66.Angled or Curved FPC-软板角度/弯曲67.Welding Thru-hole-焊盘点穿68.No Welds-没焊点69.Missing Welds-没有焊点70.Welding Peel-off-焊点脱焊71.Welding Shift-焊点点偏超出范围72.Cell tab Shift-电芯极耳偏移73.Cell Tab too ling-电芯极耳超长74.Cell Tab too short-电芯极耳超短75.Welding burst/Burn Mark-点炸76.Welding Burn Mark-焊点点黑77.Cell Tab Lifted-电芯极耳翘起（点焊后）78.Cell Tab wrinkle-电芯极耳褶皱（点焊后）。
锂电池专业英语
盖板c o v e r b o a r d 底板s o l e p i e c e 钢珠s t e e l b a l l 压钢珠p r e s s s t e e l b a l l 防爆阀v a l v e p r e v e n t i n g e x p l o s i o n大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic weldingThe terminating voltage in discharge of the battery is volt. The limited voltage in charge of the battery is volt.三元素Nickle-Cobalt-Manganese Lithium Oxidethree elements materials钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing devicevacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces 辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper。
锂离子电池专业英语
锂离子电池常用专业英语（一）序号首字母英文中文1 A aging 老化2 B battery charger 充电器3 black-fleck 黑斑4 C cap 盖板5 capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 charge(capacity) retention 荷电（容量）保持10 checking code 检码11 concave spot 凹点12 constant current charge 恒流充电13 constant current discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 纠正措施16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 D dark trace 暗痕20 degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 E Electrical and MechanicalServices Department 机电部26 electrolyte 电解，电解液27 empaistic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 腐蚀32 explosion-proof line 防爆线33 F first inspection 首检34 formation 化成35 fracture 断裂36 I inspection 检验37 insulate 绝缘38 internal resistance 内阻39 J jellyroll 卷芯40 joint 接缝，结合点41 L laser deflecting 偏光42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接-平焊laser welding-standing weld 激光焊接-立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51 meet requirement 达到要求52 memory effects 记忆效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE膜64 pit 坑点65 placing cells into the box 电芯装盒66 point inspection 点检67 preventive measures 预防措施68 pricking the tapes 扎孔69 process inspection 制程检验70 put the battery piled up 将电芯叠放在一起71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量控制74 quality improvement 质量改进75 quality match 品质配对76 quality planning 质量策划77 R rated capacity 额定容量78 recharge 再充电79 refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面，反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜84 S safety vent 安全阀85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smudginess 污物91 spot welding by laser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压储存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqualified products 不合格品104 W wave 波浪105 working procedure 工序（二）盖板 cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic welding三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials 钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing device vacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper锂离子电池设计专业英语Capacity 容量Battery Thickness 电池厚度Battery width 电池宽度Battery length 电池高度Impedance 内阻Can thickness 壳体厚度Can wall thickness 壳体壁厚Can bottom thikness 壳体底部厚度Can lid thickness 壳体盖板厚度PP film thickness PP胶厚度Ni (AL) tab thickness Ni（Al）极耳厚度Battery width 电池宽度Can width margin 电池宽度留边Can length 壳体长度Can cross area 壳体体积Winding pin width 卷针宽度Can Side residue 壳边残余Naked battery thickness 裸漏电池厚度Naked battery width 裸漏电池宽度Naked battery length 裸漏电池高度Cathode formulation 阴极含量Cathode material specific capacity 阴极克比容量Cathode 阴极装填Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode weight 阴极重量Cathode thickness 阴极厚度Cathode elongation rate 延伸率Cathode actual length 阴极实际长度Cathode design length 阴极设计长度Cathode width 阴极宽度Cathode Scratched area width 阴极涂片宽度Al foil density 铝箔密度Al foil thickness 铝箔厚度Cathode weight 阴极重量Separator thickness 隔离膜厚度Separator length 隔离膜长度Separator width 隔离膜宽度Separator density 隔离膜密度Separator weight 隔离膜重量Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode loading 阳极装填量Anode area density 阳极面密度Anode bulk density 阳极体积密度Anode thickness 阳极厚度Anode length 阳极长度Anode width 阳极宽度Anode scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度Anode weight 阳极重量Cathode Tab length 阴极极耳长Cathode Tab width 阴极极耳宽Cathode Tab thickness 阴极极耳厚度Anode Tab length 阳极极耳长度Anode Tab width 阳极极耳宽度Anode Tab thickness 阳极极耳厚度Adhesive tape Length 胶带长度Adhesive tape Width 胶带宽度Adhesive tape thickness 胶带厚度Assembly adhesive tape 装配胶带Bottom length 底部长度Bottom Width 底部宽度Bottom Thickness 底部厚度Top length 顶部长度Top Width 顶部宽度Top Thickness 顶部厚度Welding length 焊接长度Welding Width 焊接宽度Welding Thickness 焊接厚度Electrolyte 电解液Battery Impedance 电心内阻Battery weight 电池重量Can wall thickness 壳体壁厚Can bottom thikness 壳体底厚Can lid thickness 盖板厚度Can width margin 壳体边缘宽度Can Side residue 壳体留边Cathode formulation 阴极含量Cathode material specific capacity 阴极克容量Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode elongation rate 阴极延伸率Cathode scratched area width/Pin width 阴极刮粉宽Al foil density 铝箔密度Al foil thickness 铝箔厚度Separator thickness 隔离膜厚度Separator density 隔离膜密度Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode bulk density 阳极体积密度Anode Scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度欢迎您的下载，资料仅供参考！致力为企业和个人提供合同协议，策划案计划书，学习资料等等打造全网一站式需求。
锂电池行业翻译资料英文
锂电池行业翻译资料英文IntroductionThe lithium battery industry is a rapidly growing sector that plays a crucial role in various applications, including electric vehicles, portable electronics, and renewable energy storage systems. To stay updated with the latest advancements and trends in this industry, it is important to access reliable and accurate translation resources in English. This document aims to provide valuable translation materials related to the lithium battery industry. Please note that the translations provided are for reference purposes only and may require further verification.1. Lithium Battery OverviewLithium batteries are rechargeable energy storage devices that use lithium ions to facilitate the flow of charge between electrodes. They are known for their high energy density, longer cycle life, and comparatively higher voltage levels. Lithium batteries are widely used in portable electronic devices, such as smartphones and laptops, due to their lightweight and compact design.2. Lithium Battery TypesThere are several types of lithium batteries, including:2.1 Lithiumion Battery (Liion)Liion batteries are the most common type of lithium batteries used today. They are known for their high energy density, low selfdischarge rates, and long cycle life. Liion batteries are extensively employed in electric vehicles, consumer electronics, and energy storage systems.2.2 Lithium Polymer Battery (LiPo)LiPo batteries are a type of lithium battery that use a solid polymer electrolyte instead of a liquid electrolyte used in Liion batteries. They offer higher energydensity, improved flexibility, and enhanced safety compared to Liion batteries. LiPo batteries are commonly used in smartphones, tablets, and wearable devices.2.3 Lithium Iron Phosphate Battery (LiFePO4)LiFePO4 batteries, also known as lithium iron phosphate batteries, are a type of lithium battery that utilize iron phosphate as the cathode material. They offer improved safety, longer cycle life, and better thermal stability compared to other lithium battery types. LiFePO4 batteries are often used in power tools, electric vehicles, and renewable energy storage systems.3. Lithium Battery Manufacturing ProcessThe production of lithium batteries involves several key steps, including:3.1 Electrode PreparationDuring this process, the electrode materials, such as lithium cobalt oxide (LiCoO2) for the cathode and graphite for the anode, are prepared. These materials are coated onto metal foils and then dried to form the electrode sheets.3.2 Cell AssemblyIn this step, the electrode sheets are assembled with a separator, which prevents the electrodes from coming into contact with each other. The electrodes are then rolled or stacked together and inserted into a metal or plastic casing.3.3 Electrolyte FillingThe casing is filled with a liquid electrolyte that allows the lithium ions to move between the electrodes during charging and discharging. The electrolyte is typically a mixture of lithium salts dissolved in an organic solvent.3.4 Battery SealingTo ensure the integrity and safety of the battery, the casing is sealed to prevent leakage of the electrolyte and protect the internal components from external influences. Various sealing methods, such as heat sealing or ultrasonic welding, are used for this purpose.3.5 Battery Testing and Quality ControlEvery battery undergoes stringent testing to ensure its performance and safety. This includes capacity testing, cycle life testing, and checking for any manufacturing defects. Batteries that pass these tests proceed to the next stage, while defective ones are discarded or undergo further analysis.4. Lithium Battery Safety ConsiderationsWhile lithium batteries offer numerous benefits, it is essential to consider safety precautions due to their inherent risks. Some key safety considerations include:Temperature Control: Lithium batteries should be operated within their recommended temperature ranges to prevent thermal runaway and potential hazards.Overcharge and Overdischarge Protection: Appropriate charging and discharging circuits should be implemented to prevent overcharging or discharging, which could lead to reduced battery life and safety risks.Transportation and Storage: Proper packaging, labeling, and handling procedures must be followed to ensure the safe transportation and storage of lithium batteries. Protection Circuitry: Lithium batteries often incorporate protection circuitry to monitor voltage, temperature, and prevent short circuits or other malfunctions.ConclusionThe translation materials provided in this document offer insights into the lithium battery industry. These resources can serve as valuable references for individuals seeking English translations related to various aspects of this industry, including battery types, manufacturing processes, and safety considerations. It is crucial to verify the accuracy of the translations and supplement them with updated and reliable information from reputable sources.。
锂电池术语解释及英文对照N0.10004
锂电池专业术语解释及英文对照Author:HarrisonPart 1 Basic1.锂原电池（lithium primary battery）也称为一次锂电池，负极为锂，且被设计为不可充电的电池。
包括单体锂原电池和锂原电池组。
2.锂蓄电池（Rechargeable lithium battery）锂离子电池和锂金属蓄电池统称为锂蓄电池（也称为可充放锂电池，二次锂电池）。
3.锂离子电池（lithium ion battery）利用锂离子作为导电离子，在正极和负极之间移动，通过化学能和电能相互转化实现充放电的电池。
包括单体锂离子电池和锂离子电池组。
4.单体锂离子电池（lithium ion cell）锂离子电池的基本单元，由电极、隔膜、外壳和电极片等在电解质环境下构成。
金属锂蓄电池（rechargeable lithium metal battery）电池中负极侧含有金属锂的锂蓄电池。
也称为可充放金属锂电池。
5.液态锂蓄电池（liquid rechargeable lithium battery）电池中只含有液体电解质的锂蓄电池。
6.非水有机溶剂锂蓄电池（nonaqueous rechargeable lithium battery）电解质为有机溶剂的液态锂蓄电池。
7.水系锂蓄电池（aqueous rechargeable lithium battery）电解质为水溶剂的液态锂蓄电池。
8.混合固液电解质锂蓄电池（mixed solid liquid electrolyte rechargeable lithium battery）电池中同时含有液体和固体电解质的锂蓄电池。
①电池单体中固体电解质质量或体积占单体中电解质总质量或总体积之比达到一半，或者单体中一侧电极含有液体电解质，另一侧电极只含有固体电解质，这两种均称为半固态电解质锂蓄电池，有时简称为半固态锂电池；②单体中固体电解质质量或体积分数超过一半，液体电解质的质量或体积分数低于一半的，有时称为准固体电解质锂蓄电池或准固态锂电池；③液体电解质的质量或体积分数低于电解质总质量或总体积分数5%的，有些作者称之为固态电解质锂蓄电池，或者固态锂电池。
2021年锂电池专业英语
盖板cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion欧阳光明（2021.03.07）大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic weldingThe terminating voltage in discharge of the battery is 3.0 volt.The limited voltage in charge of the battery is 4.2 volt.三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven 搅拌机mixing device vacuum mixing device*欧阳光明*创编 2021.03.07涂布机coating equipment 裁纸刀paper knife ,,,,,,cutting knife 分条机equipment for cutting big piece to much pieces 辊压机roll press equipment 电阻点焊机spot welding machine 超声点焊机ultrasonic spot welding machine 卷绕机winder 自动叠片机auto laminating machine 激光焊机laser welding machine 注液机infusing machine 真空注液机vacuum infusion machine 预充柜pre-charge equipment*欧阳光明*创编 2021.03.07化成柜formation systems 分容柜grading systems 测试柜testing systems 内阻仪battery inner resistance tester 万用表multimeter转盘式真空封口机turntable type vacuum sealing machine 自动冲膜机automatic aluminum membrane shaper。
锂离子电池专业英语
锂离子电池常用专业英语（一）序号首字母英文中文1 A aging 老化2 B battery charger 充电器3 black-fleck 黑斑4 C cap 盖板5 capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 charge(capacity) retention 荷电（容量）保持10 checking code 检码11 concave spot 凹点12 constant current charge 恒流充电13 constant current discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 纠正措施16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 D dark trace 暗痕20 degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 E Electrical and MechanicalServices Department 机电部26 electrolyte 电解，电解液27 empaistic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 腐蚀32 explosion-proof line 防爆线33 F first inspection 首检34 formation 化成35 fracture 断裂36 I inspection 检验37 insulate 绝缘38 internal resistance 内阻39 J jellyroll 卷芯40 joint 接缝，结合点42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接-平焊laser welding-standing weld 激光焊接-立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51 meet requirement 达到要求52 memory effects 记忆效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE膜64 pit 坑点65 placing cells into the box 电芯装盒66 point inspection 点检67 preventive measures 预防措施68 pricking the tapes 扎孔69 process inspection 制程检验70 put the battery piled up 将电芯叠放在一起71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量控制74 quality improvement 质量改进75 quality match 品质配对76 quality planning 质量策划77 R rated capacity 额定容量78 recharge 再充电79 refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面，反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smudginess 污物91 spot welding by laser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压储存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqualified products 不合格品104 W wave 波浪105 working procedure 工序（二）盖板cover board底板solepiece钢珠steel ball压钢珠press steel ball防爆阀valve preventing explosion大电流(倍率)放电discharge in high rate current标称电压Normal voltage标称容量normal capacity放电容量discharge capacity充电上限电压limited voltage in charge放电下限电压terminating voltage in discharge恒流充电constant current charge恒压充电constant voltage charge恒流放电constant current discharge放电曲线discharge curve充电曲线charge curve放电平台discharge voltage plateau容量衰减capacity attenuation起始容量initial discharge capacity流水线pipelining传送带carrying tape焊极耳welding the current collector卷绕wind叠片layer贴胶带stick tape点焊spot welding超声焊ultrasonic welding三元素Nickle-Cobalt-Manganese Lithium Oxide three elements materials 钴酸锂Cobalt Lithium Oxide锰酸锂Manganese Lithium Oxide石墨graphite烘箱oven真空烘箱vacuum oven搅拌机mixing device vacuum mixing device涂布机coating equipment裁纸刀paper knife ,,,,,,cutting knife分条机equipment for cutting big piece to much pieces辊压机roll press equipment电阻点焊机spot welding machine超声点焊机ultrasonic spot welding machine卷绕机winder自动叠片机auto laminating machine激光焊机laser welding machine注液机infusing machine真空注液机vacuum infusion machine预充柜pre-charge equipment化成柜formation systems分容柜grading systems测试柜testing systems内阻仪battery inner resistance tester万用表multimeter转盘式真空封口机turntable type vacuum sealing machine自动冲膜机automatic aluminum membrane shaper锂离子电池设计专业英语Capacity 容量Battery Thickness 电池厚度Battery width 电池宽度Battery length 电池高度Impedance 内阻Can thickness 壳体厚度Can wall thickness 壳体壁厚Can bottom thikness 壳体底部厚度Can lid thickness 壳体盖板厚度PP film thickness PP胶厚度Ni (AL) tab thickness Ni（Al）极耳厚度Battery width 电池宽度Can width margin 电池宽度留边Can length 壳体长度Can cross area 壳体体积Winding pin width 卷针宽度Can Side residue 壳边残余Naked battery thickness 裸漏电池厚度Naked battery width 裸漏电池宽度Naked battery length 裸漏电池高度Cathode formulation 阴极含量Cathode material specific capacity 阴极克比容量Cathode 阴极装填Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode weight 阴极重量Cathode thickness 阴极厚度Cathode elongation rate 延伸率Cathode actual length 阴极实际长度Cathode design length 阴极设计长度Cathode width 阴极宽度Cathode Scratched area width 阴极涂片宽度Al foil density 铝箔密度Al foil thickness 铝箔厚度Cathode weight 阴极重量Separator thickness 隔离膜厚度Separator length 隔离膜长度Separator width 隔离膜宽度Separator density 隔离膜密度Separator weight 隔离膜重量Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode loading 阳极装填量Anode area density 阳极面密度Anode bulk density 阳极体积密度Anode thickness 阳极厚度Anode length 阳极长度Anode width 阳极宽度Anode scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度Anode weight 阳极重量Cathode Tab length 阴极极耳长Cathode Tab width 阴极极耳宽Cathode Tab thickness 阴极极耳厚度Anode Tab length 阳极极耳长度Anode Tab width 阳极极耳宽度Anode Tab thickness 阳极极耳厚度Adhesive tape Length 胶带长度Adhesive tape Width 胶带宽度Adhesive tape thickness 胶带厚度Assembly adhesive tape 装配胶带Bottom length 底部长度Bottom Width 底部宽度Bottom Thickness 底部厚度Top length 顶部长度Top Width 顶部宽度Top Thickness 顶部厚度Welding length 焊接长度Welding Width 焊接宽度Welding Thickness 焊接厚度Electrolyte 电解液Battery Impedance 电心内阻Battery weight 电池重量Can wall thickness 壳体壁厚Can bottom thikness 壳体底厚Can lid thickness 盖板厚度Can width margin 壳体边缘宽度Can Side residue 壳体留边Cathode formulation 阴极含量Cathode material specific capacity 阴极克容量Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode elongation rate 阴极延伸率Cathode scratched area width/Pin width 阴极刮粉宽Al foil density 铝箔密度Al foil thickness 铝箔厚度Separator thickness 隔离膜厚度Separator density 隔离膜密度Anode formulation 阳极含量Anode material specific capacity 阳极克容量Anode bulk density 阳极体积密度Anode Scratched area width 阳极刮粉区宽度Cu foil density 铜箔密度Cu foil thickness 铜箔厚度。
锂电池专业术语英文
锂电池专业术语英文Lithium Battery Terminology.Anode: The negative electrode of a lithium-ion battery, usually made of graphite.Cathode: The positive electrode of a lithium-ion battery, usually made of a lithium metal oxide.Cell: A single electrochemical unit, consisting of an anode, a cathode, and an electrolyte.Charge: The process of transferring electrons from the cathode to the anode.Discharge: The process of transferring electrons from the anode to the cathode.Electrolyte: A substance that conducts electricity between the anode and cathode.Intercalation: The process of lithium ions moving into and out of the electrodes.Lithium-ion battery: A type of rechargeable battery that uses lithium ions as the charge carriers.Separator: A thin, porous material that keeps the anode and cathode apart.State of charge (SOC): The amount of charge stored in the battery.State of health (SOH): A measure of the battery's overall condition.Specific energy: The amount of energy stored in the battery per unit mass.Specific power: The amount of power the battery can deliver per unit mass.Voltage: The difference in electrical potential between the anode and cathode.中文回答：负极: 锂离子电池的负极，通常由石墨制成。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
anode tab and bottom
potential falure mode and effects analysis
பைடு நூலகம்
jelly roll glue solution sysytem
revolutions per minute milligram per square centimeters micron millimeter
黏度 胶 导电性 电池壳 电池盖 高度 直径 精度 裂缝 镀层 镍 生锈 内部压力
英文 slurry binder coating slitting cathode anode aluminum foil copper foil ED foil Rolled copper foil Roll annealed copper foil lithium－ion cell／battery LiCoO2 ratio Surface Area Granularity Tap-Density material activeness electrode density bulk ratio capacity cell design guideline active material additive ＮＭＰ water content seperator inside resistance Electrolyte composition
PVDF viscosity glue reagent of conducting electricity can cap height diameter accuracy crack plating layer nickel rust inside pressure ＰＴＣ
胶带 垫片 毛刺 尺寸 变形 绝缘电压 热缩套 电极 正极 负极 正极包住负极 公差分析 滚槽 深度 浆料 一致的 涂布 分切 碾压 装配 焊接强度 滚槽 封口 化成 老化 自放电 工艺 固含量 不溶杂质 杂质 批 电压平台 吸收空气中的水分 人力/人工 容器 包装 真空度 不够的 杂质 管道 泵 过滤器 堵塞 温度计 操作工 软件
ＣＩＤ tape insolator burr dimension distortion insulated voltage
electrode cathode anode anode cover cathode tolerance analysis rolling slot deepness slurry uniformity Coating slitting Calendering assembling welding strength
optimize parameter monitor standard exceed additive fray stirrer Malfunction Annual calibration thickness detector copper foil aluminum foil alarm chart GAP of COMMA tolerance granule strip blank filter humidity scraper thermocouple blade oxidation drying area Roller gap Hydraulic pressure dust wide narrow wrinkling powder scraps metal Cutter blunt alloy EPC transportation
PFMEA temperature self-discharging rate calculagraph winding granule
刷子 消除 极耳 焊接 强度 超声焊 手套 开路 短路 中心弹性钢芯 极组 润滑剂 覆盖 偏移 烫孔针 目视检查 入壳 上绝缘片 下绝缘片 挫伤极组 焊接压力 稳定 滚刀 人工的 清洗 酒精 脱水 涂油 生锈 热缩 包装 外观 自查 喷码 编码 追溯 设备自动报警 探针 托盘 分选 程序 病毒 出货 分类 制胶系统
Binder solution system
Weighing
weight
校正计量仪器 批 比例 溶液 真空度 厘泊 转数／分 作业制导书 黏度剂 冷却水 毫克每平方厘米 微米 毫米 长度 厚度 数显千分尺 尺子 对齐度 单面的间距 极片真空烘箱 帕斯卡 质量
充电 放电 爆炸 针刺 样品 密封胶
聚合物
microporous stucture sutdown aging overheat metal particle catch fire stable
ending tape top and bottom insolator
protective tape outer insolator
calendering density of electrode between cathode tab and cap,
优化参数 班长 标准 超过 添加剂 磨损 搅拌器 故障 一年的 校准 厚度检测仪 铜箔 铝箔 报警 图 逗号辊间歇 公差 颗粒 划痕 过滤器 湿度 刮刀 热电偶 刀刃 氧化 烘干区 辊间隙 水压 灰尘 宽的 窄的 起邹 粉末 碎屑 金属 切刀 钝的 合金 感应器 运输
过程潜在失效模式 温度 自放电率 计时器 卷绕 颗粒
Pa
Quantity ARC charge discharge exlposion nail penetration sample Airproof glue polymer
cylinderical internal structure charge and discharge characteristics hipot Tolerance g
称重
重量
brush eliminate tab welding strength ultrasonic welding glove open-circiut short circuit central pin J/R lubricant cover deflexion pin of opening hole visual inspection insertion top insulator bottom insulator scratching J/R welding pressure stable rolling sword manual Washing alcohol dehydration coating oil rust Hot molding packing appearance self-check spraying code ID trace system automatic alarm probe tray sorting procedure virus shipment classify
锂离子电池专业英语BY JANE 中文 匀浆 胶液 涂布 分切 正极 负极 铝箔 铜箔 电解铜箔 压延铜箔 压延退火铜箔 锂离子 电池 钴酸锂 比表面 粒度 振实密度 材料活性 电极密度 体积比容量 电池设计方针 导电添加剂 添加剂 NMP（Ｎ－甲基吡咯烷酮） 水分含量 隔膜 内阻 电解液 成分 六氟磷酸锂
sealing formation aging self discharge craft solid content dissolve impurity impurity batch voltage platform absorb water of air manpower/manual work container wrapping vacuum degree insufficient impurity pipeline pump filter jam thermometer operator software
方型 圆型 内部结构 充放电特性
公差 克 槽口 微孔结构 切断 老化 过热 金属屑 着火 稳定的
verify measuring apparatus lot Proportion solution Vacuum degree cp
rpm
WI Viscometer Cooling water mg/cm2 μm mm length thickness Digital micrometer Ruler Superposition degree Blank of first side Vacuum hot oven