乐彩750说明
乐彩750写真机操作维修指南概要
乐彩750写真机操作维修指南概要第一部分：操作指南（800字）1.开机和关机1.1打开电源按钮1.2等待写真机启动1.3按下关机按钮关闭写真机2.选择模式2.1使用功能菜单按钮进入菜单2.2通过方向键选择不同的模式2.3确认选择的模式3.设置打印参数3.1进入设置菜单3.2调整打印质量、纸张尺寸等参数3.3保存设置并退出菜单4.打印照片4.1连接手机或相机到写真机4.2通过操作菜单选择照片打印4.3确认好打印参数后按下打印按钮5.查看照片5.1进入预览模式5.2使用方向键查看不同的照片5.3确定要查看的照片并按下确认键6.储存照片6.1连接USB存储设备到写真机6.2进入存储菜单6.3选择要保存的照片6.4保存照片到USB存储设备第二部分：维修指南（400字）1.故障排除1.1打印质量问题-确认打印质量参数是否正确设置-清洁打印头-更换打印墨盒1.2无法连接手机或相机-确保设备已连接写真机-重新插拔连接线-检查设备是否支持写真机的连接方式2.清洁和保养2.1清洁外壳-使用柔软的布轻轻擦拭外壳-避免使用溶剂或强化学物质清洁2.2清洁打印头-使用打印机的清洗功能清洁打印头-如无清洗功能，可用布轻轻擦拭打印头2.3保养存储设备-定期备份存储设备中的照片-避免在湿度较高的环境中使用存储设备3.维修和更换部件3.1维修电源问题-检查电源线是否插好-检查电源插头是否损坏-如有必要，更换电源线或插头3.2更换打印头-参考用户手册中的更换指南-注意正确安装新的打印头-测试新安装的打印头是否正常工作4.2提供详细的故障信息和操作步骤。
彩金单挑游戏机说明书
彩金单挑游戏机说明书更多游戏机说明请浏览：一、基本游戏规则：游戏主要是以猜八幅扑克的花色和大小王来决定玩家输赢，猜对时机器会根据相应的赔率规则来赔。
游戏由一至八人来玩，每轮提供100局供玩家猜，可提前将100局记录打印封存，加大玩家中奖机率。
机台的外观跟真人龙虎外观一样，就看你要的游戏画面是有美女的还是就是扑克牌的那种。
赔率说明：A、黑桃、红桃赔率： 3.8倍B、草花、方块赔率：4倍C、大小王赔率：20倍（注：出王时，别的花色押分退回）本机台可限红、限注（本机器的出厂设定为建议设定值，以供参考）。
二、游戏设置：游戏的设置及程序调节全部是用以下模块（见图示）完成，欲进入系统设置，可按下列相对应的键进入。
K8 K7 K6 K5K4 K3 K2 K1图示设置模块按[K3]键进入查账功能（如图）：图示：查账进入查账系统后，其中第一次显示为总查帐，如果查分机账可根据画面提示按相应的按键进入。
总开分：玩家上的分数。
总洗分：玩家总退分。
总押分：玩家押分累计。
总赢分：玩家总赢的分数。
局数：开机至现在的局数（每一百把算一局）。
总输赢：总开分-总洗分。
VERION：表示游戏版本。
按[K5]键进入设定功能（如图）图示：设定进入设定系统后，系统提示输入密码（初始密码为空），按[K8]键直接进入设定。
开洗分数：指上、下分的最低限额。
（范围：10-2000）最大押分：指最高押分限额。
（范围：4000-79992）最小押分：指最小押分限额。
（范围：1-100）限红：指游戏经营者最大赔分限额。
（范围：800-3000）保单选择：A.不打保单：不打印保单；B.打印保单：打印机打前72局的单，后面28局走难度；C.保单切纸：打印机打完数据切纸，不可以打开保单箱门；D.切纸开门：打印机打完数据切纸，可以打开保单箱门，针对挂单；打印保单一场结束后，进入下一场时，主机画面会显示（游戏结束）整机等待5分钟；这时应该打开保单箱，拿出保单，供玩家对保单。
Beckman-Coulter LH750全自动血液分析仪使用与总结
Coulter LH750(以下简称LH750)是贝克曼库尔特公司推出的高层次的全自动五分类血液细胞分析仪。
有5种不同的分析模式，每小时最高分析速度为110个样本，能提供31项细胞分析参数，白细胞分类散点图及各种怀疑性、限定性旗标。
LH750基于先进的V(电阻抗)、C(高频传导)、S(激光散射)技术对白细胞进行精确的分类。
并可进行网织红细胞的计数及分类。
作者所在科室于2008年4月引进LH750分析仪一台，至今已有一年半的时间，该仪器的使用大大提高了实验室内的分析速度和工作效率。
但是在实际使用过程中由于各种主客观因素的影响，降低了测定结果的准确性和可靠性。
现将我们在日常工作中LH750的一些使用及常见故障排除情况总结如下，以便与使用该仪器的同行共同探讨。
1 使用1.1 标本标本须由静脉穿刺取得，不提倡毛细血管采血法。
盛装的试管有真空采血试管和非真空试管。
推荐使用真空采血管，所注入血液的量必须达到刻度线以上，以保证仪器在吸样过程中有足够的血细胞供分析。
必须充分抗凝，上机前再次颠倒混匀，既可以使试管内的血液均匀分布，还可以在混匀过程中检查血液中有无明显凝块，以免堵塞吸样针。
1.2 抗凝剂使用EDTA-K2抗凝剂，其对细胞形态和血小板计数的影响较小。
作者所在实验室曾发生因血常规试管中加入了枸橼酸钠而造成血液部分凝固血小板计数明显降低的差错事故，给了全科人员一次深刻的教训。
1.3 样本编号LH750英文工作站提供两种不同的编号方式。
方式一：在主界面上点击添加样品请求→自动编号顺序→添加此样品要求，此方法准确可靠，不易跳号。
方式二：点击分析配置→自动编号→起始为，此方法简便快捷，但容易跳号，因此需要操作者注意。
1.4 质控仪器自检程序完成后，观察各项参数及空白值。
合格后再进行每日的质控物测定，只有质控物测定值符合要求方可进行常规标本的测定。
1.5 上机将编好的血常规试管按顺序放入仪器的试管架中，2小时内进行自动测定。
乐彩750等热发泡写真机故障处理与耗材认知
乐彩750等热发泡写真机故障处理与耗材认知热发泡写真机比较有名的是乐彩750、5500、5800、6416、6640等，但是与压电机相比，这类机器速度慢，精度差，现在均已经停止生产，但是还有很多朋友在用这类机器。
为了方便各位处理问题，乐彩技术员们整理出一些处理的技巧，欢迎各位学习。
1 750灰也就是750—H 采用通用型208喷头采用热发泡系类墨水 300dpi750常见问题：液晶屏显示“Carriage Axis Failure故障原因：1、皮带轮与铜套的损坏造成阻力过大；2、一般电机的寿命为800-1200小时，使用时间超出此范围可能引起电机的损坏；解决方法：检查皮带轮轴承的转动是否正常，如出现轴承变形或转动不顺畅，说明皮带轮损坏；2、拆卸铜套，进行清洁擦拭然后再重试；3、首先进行“伺服循环”测试，如果阻力数值不断增加或噪音过大，说明电机使用时间过长，需要换新的电机；液晶屏显示“Bad Carriage Paper Sensor”故障原因：1、测纸器排线与喷墨板的连接端口松动；2、内部线路短路造成测纸器的损坏；解决方法：1、关掉电源，用酒精擦拭测纸器排线后重新启动；2、更换测纸感应器；液晶屏显示“Servioeboj:Preallocmemout”故障原因：打印文件过大造成内存不足；解决方法：更换内存或扩展内存大小；机器在启动时，墨车左右乱跳故障原因：1、数据线未连接好；2、光栅检测器未连接好；3、伺服电机烧坏、主板L6203芯片烧坏；解决方法：1、重新插拔数据线或换数据线；2、重新插拔光栅检测线；3、换伺服电机后再换主板；写真机启动墨车移动到左端报错故障原因：1、写真机测纸器损坏；2、写真机小车板与测纸器未连接好；解决方法：1、换测纸器；2、将测纸器的线和小车板的接口对齐再插紧；草图模式2Pass 8平方生产模式3Pass 6平方一般品质模式4Pass 4平方高品质模式 6Pass 3平方2 750白采用通用型208喷头采用热发泡系类墨水 300dpi3 5500 采用416喷头采用416系类墨水 1200dpi416系列常见问题：机器不联机故障原因：1 一般都是电脑系统的问题2 主板和USB线解决方法：1 换台电脑或重新做系统2 更换主板或USB线托架过流故障原因：1 电机老化了2 小车架断裂决方法：1更换电机2 更换小车架打图乱码故障原因：1 电脑数据发送慢2 喷头干扰3光栅或光栅解码器脏了解决方法：1 换电脑或者先把作业打印到文件夹2 检查一下喷头看看那个喷头产生干扰就换了那个喷头3 擦拭光栅或换光栅解码器草图模式2Pass 12平方生产模式3Pass 10平方一般品质模式4Pass 8平方高品质模式 6Pass 6.8平方4 5800 采用416喷头采用416系类墨水 1200dpi5 6416A 采用416喷头采用416系类墨水 1200dpi6 6416C 采用416喷头采用416系类墨水 1200dpi7 6208 采用208加密喷头采用热发泡系类墨水 1200dpi 6208的问题跟416系列问题一样8 6640 采用640喷头采用热发泡系类墨水 1200dpi6640机型常见问题：托架轴故障故障原因：1 数据线没插好2 电机3 小车架阻力大解决方法：1 重新插拔数据线2 电机老化了更换电机3 用缝纫机油擦拭光轴或更换铜套墨水夹故障故障原因：1 喷头墨水过高2 喷头墨水太多或少解决方法：1 更换喷头2 添加或减少墨水测不到纸张故障原因：1 机体有地方露白2 测纸器坏了解决方法：1 用黑色的油笔涂抹露白的地方2 更换测纸器草图模式2Pass 22平方生产模式3Pass 17平方一般品质模式4Pass 12.8平方高品质模式 6Pass 7平方640、416、208的区别416喷头208喷头640喷头640、416和208的区别在于芯片以上图片可以对比一下208喷头的加密区别208不加密 208加密208不加密 208加密208不加密就是看喷头上面有没有写208，加密喷头上面写的有208 ，还有就是从喷头盒上区分 208（银/silver）是不加密的 208PIus是加密的以上图片大家可以区分发泡机墨水的区分下面的图片(左图）是热发泡系列墨水（右图）是416系列墨水热发泡系列的墨水适用机型： 750灰、750白、6208、6640这几款机型416系列的墨水适用机型： 5500、5800、6416A、6416C这几款机型图1大家可以仔细看下图1上面写的“热发泡系列”这几个字这就是热发泡系列的墨水图2上面写的“416系列”这就是416系列的墨水图2这个是208不加密的这个是208加密的这个是416喷头他没有加密和不加密一说以上就是让大家认识的发泡机型和对喷头墨水的认识。
触摸屏 BDD 750-_P... 使用说明书 English
Touch Display BDD 750-_P…User’s GuideThe detailed operating manuals of all devices as well as the declarations of conformity can also be downloaded from the Internet at .All contents included in this manual are protected by the terms of use and copyrights ofBalluff GmbH. Any reproduction, modification, usage or publication in other electronic and printed media as well as in the internet requires prior written authorization by Balluff GmbH.Table of content1.Safety Instructions and Responsibility (4)1.1.General Safety Instructions (4)e according to the intended purpose (4)1.3.Installation (5)1.4.Cleaning, Maintenance and Service Notes (5)2.Introduction (6)2.1.Operation mode (6)3.Electrical Connections (7)3.1.DC Power Supply (7)3.2.Auxiliary Voltage Output (7)3.3.RS-485 inputs and outputs (8)3.4.Control Inputs (9)3.5.Relay-Output (9)4.Display and touch screen (10)4.1.Screen structure for parametrization (10)4.2.Screen structure in operation (11)4.3.Error Message (12)5.Parameter / Overview-Menu Structure (13)5.1.General Menu (14)5.2.Encoder Properties (17)5.3.Preselection Values (18)5.4.Preselection 1 Menu (19)5.5.Preselection 2 Menu (21)5.6.Preselection 3 Menu (22)5.7.Preselection 4 Menu (23)mand Menu (24)5.9.Display Menu (26)5.10.Linearization Menu (27)6.Appendix (28)6.1.Parameter / serial codes (28)6.2.Linearization (32)6.3.Dimensions (34)6.4.Technical Specifications: (35)1. Safety Instructions and Responsibility1.1. General Safety InstructionsThis operation manual is a significant component of the unit and includes important rules and hints about the installation, function and usage. Non-observance can result in damage and/or impairment of the functions to the unit or the machine or even in injury to persons using the equipment!Please read the following instructions carefully before operating the device and observe all safety and warning instructions! Keep the manual for later use.A pertinent qualification of the respective staff is a fundamental requirement in order to use these manual. The unit must be installed, connected and put into operation by a qualified electrician.Liability exclusion: The manufacturer is not liable for personal injury and/or damage to property and for consequential damage, due to incorrect handling, installation and operation. Further claims, due to errors in the operation manual as well as misinterpretations are excluded from liability.In addition the manufacturer reserves the right to modify the hardware, software or operation manual at any time and without prior notice. Therefore, there might be minor differences between the unit and the descriptions in operation manual.The raiser respectively positioner is exclusively responsible for the safety of the system and equipment where the unit will be integrated.During installation or maintenance all general and also all country- and application-specific safety rules and standards must be observed.If the device is used in processes, where a failure or faulty operation could damage the system or injure persons, appropriate precautions to avoid such consequences must be taken.1.2. Use according to the intended purposeThe unit is intended exclusively for use in industrial machines, constructions and systems. Non-conforming usage does not correspond to the provisions and lies within the sole responsibility of the user. The manufacturer is not liable for damages which have arisen through unsuitable and improper use.Please note that device may only be installed in proper form and used in a technically perfect condition (in accordance to the Technical Specifications). The device is not suitable for operation in explosion-proof areas or areas which are excluded by the EN 61010-1 standard..1.3. InstallationThe device is only allowed to be installed and operated within the permissible temperature range. Please ensure an adequate ventilation and avoid all direct contact between the device and hot or aggressive gases and liquids.Before installation or maintenance, the unit must be disconnected from all voltage-sources. Further it must be ensured that no danger can arise by touching the disconnected voltage-sources.Devices which are supplied by AC-voltages must be connected exclusively by switches, respectively circuit-breakers with the low voltage network. The switch or circuit-breaker must be placed as near as possible to the device and further indicated as separator.Incoming as well as outgoing wires and wires for extra low voltages (ELV) must be separated from dangerous electrical cables (SELV circuits) by using a double resp. increased isolation.All selected wires and isolations must be conform to the provided voltage- and temperature-ranges. Further all country- and application-specific standards, which are relevant for structure, form and quality of the wires, must be ensured. Indications about the permissible wire cross-sections for wiring are described in the Technical Specifications.Before first start-up it must be ensured that all connections and wires are firmly seated and secured in the screw terminals. All (inclusively unused) terminals must be fastened by turning the relevant screws clockwise up to the stop.Overvoltage at the connections must be limited to values in accordance to the overvoltage category II.For placement, wiring, environmental conditions as well as shielding and earthing/grounding of the supply lines the general standards of industrial automation industry and the specific shielding instructions of the manufacturer are valid.1.4. Cleaning, Maintenance and Service NotesTo clean the front of the unit please use only a slightly damp (not wet!), soft cloth. For the rear no cleaning is necessary. For an unscheduled, individual cleaning of the rear the maintenance staff or assembler is self-responsible.During normal operation no maintenance is necessary. In case of unexpected problems, failures or malfunctions the device must be shipped for back to the manufacturer for checking, adjustment and reparation (if necessary). Unauthorized opening and repairing can have negative effects or failures to the protection-measures of the unit.2. IntroductionThe display device is designed for panel mounting. It is universally applicable, with its intuitive operation and the extensive features.2.1. Operation modeAll functions are can be configured in the parameter menu.The device can be set to one of the following operation modes:•DISTANCE (Distance measurement)The scaling (setting of the display unit) is set with the parameter FACTOR and DIVIDER. Whenmeasuring the distance, the default setting (FACTOR = 1, DIVIDER = 1 and DECIMAL POINT = 3) corresponds to a position display in the unit "mm" in the following display format: "00000.000" mm.For example, to display a position in "inch" with three decimal places as well, the parameterFACTOR must be set to 10 and the parameter DIVIDER to 254. The unit "inch", which is to bedisplayed in the display, is set in the parameter SCALE UNITS.•ANGLE (Angle Measurement)For angle measurement, the default setting (FACTOR = 1, DIVIDER = 1, and DECIMAL POINT = 3) corresponds to an angle display of 0 – 360 degrees with three decimal places.With the parameter LENGTH PER REVOLUTION, the distance travelled is set per 360 degrees (in millimeters). With the parameters FACTOR and DIVIDER, the display can be scaled again if necessary. (for example, to hide decimal places). The unit “degree” can be set in the SCALE UNITS parameter.3. Electrical ConnectionsThe terminal screws should be tightened with a slotted screwdriver (blade width 2mm).3.1. DC Power SupplyThe unit accepts DC supply from 18 to 30 V at the terminals 1 and 2. The power consumption depends on the level of the supply voltage with approx. 100 mA and the additional current required at the Auxiliary Voltage Output.All GND terminals are internally interconnected.3.2. Auxiliary Voltage OutputTerminal 3 and 4 provide an auxiliary output for supply of sensors and encoders.The output voltage depends on the power supply.The encoder voltage is approx. 1 V lower than the power supply voltage at terminal 1 and 2 and should be loaded with max. 250 mA.The auxiliary voltages output is switchable from 24 VDC to 5 VDC.3.3. RS-485 inputs and outputsAt Terminal 5, 6, 7 and 8, the connection is available for the RS485 signals (Init + Sart-Stop impulse). Wiring for RS485 signals:DPI-Measurement mode:On the Init line, the Init impulse is sent to position encoder at regular intervals, whose rising flank triggers a measurement.T Init : 1…5 µsT Start: 3…5 µsT Stop: 3…5 µs3.4. Control InputsThe three control inputs at terminal 10, 11 and 12 have HTL PNP characteristics.In the COMMAND MENU the programmable functions for the control inputs can be assigned. Available functions are: display switching, locking the touch screen or release the lock function of the control or relay outputs.Wiring of the control inputs:Unconnec ted PNP inputs are always “LOW.All inputs are designed to receive impulses from electrical impulse sources.Notice for mechanical switching contacts:When exceptionally mechanical contacts are used, please connect an external capacitor between GND (-) and the corresponding input (+). A capacity of 10 µF will reduce the input frequency to20 Hz and miscounting due to contact bouncing will be eliminated.3.5. Relay-OutputTwo relay outputs with potential-free changeover contacts are available at terminal 27, 28, 28, 30, 31 and 32. Switching conditions can be set in the PRESELECTION MENU. The switching states are displayed (display with unit and status bar) as K1 and K4.AC-switching capacity max 250 VAC/ max 3 A / 750 VADC-switching capacity max 150 VAC/ max 2 A / 50 WWiring of the relay outputs4. Display and touch screen4.1.Screen structure for parametrizationThe parameter menus and the parameters are described in chapter 5.Start setup procedure:To edit the parameters,press the touchscreen for 3 seconds.Menu selection:Select the parameter menu via arrow buttons and confirm with “OK”.The menu selection can be terminated with …C“.Parameter selection:Select the parameter via arrow buttons and confirm with …OK“.The parameter selection can be terminated with …C“.Parameter editing:Edit the parameter via arrow button up and down, shift cursor via left and right and save with …OK“.The parameter editing can be terminated with …C“.4.2. Screen structure in operationThe following displays are available during operation. Depending on the device version and the selected operating mode, only certain representations are displayed.Display with unit and status barTo switch to the next display,press the touch screen.Display with command keysTo switch to the next display, press the top of thescreen. Functions of the keyboard commands see"Command Menu". (Display can be deactivated by the"Skip Commands" parameter in the "Display Menu".)Display for quick start for enter preselection values(PRESELECT VALUES)To switch to the next display, press the top of thescreen or the “skip” button.Display with minimum and maximum valueTo switch to the next display, press the top of thescreen or the “skip” button.4.3. Error MessageERROR: MAXIMUM DISPLAY VALUEDisplay value is greater than + 99,999,999ERROR: MINIMUM DISPLAY VALUEDisplay value is less than-99,999,999ERROR: POS. ENC. OUT OF RANGENo position encoder or position encoder outside thelimitsIn case of error, the measurement result is set to 0.5. Parameter / Overview-Menu StructureThis section provides an overview of the menus and their parameters. The menu names are printed bold and the associated parameters are listed under the menu name. Depending on the device version and the selected operation mode, only the necessary menus / parameters are shown.5.1. General Menu5.2. Encoder PropertiesThis menu is used to set the preselection values or the switching points.The preselection values / switching points are always referred to the display value.(Position value relative to the reference zero point or machine zero that was stored in the parameter offset.)Continuation …Preselection 1 Menu“:5.8. Command MenuINPUT CONFIG must be set to active LOW / HIGH (d) = dynamic switching (edge evaluation)INPUT CONFIG must be set to RISING/FALLING EDGEContinuation …Command Menu“:5.9. Display Menu5.10. Linearization MenuThe linearization function is defined in this menu. This menu will only be showed, if the LINEARIZATION MODE in GENERAL MENU is selected.Linearization description and examples are shown in the appendix.6. Appendix6.1. Parameter / serial codesContinuation …Parameter / serial codes”:Serial codes of commands:6.2. LinearizationThe linearization function of this unit allows converting a linear input signal into a non-linear developing (or vice versa). There are 24 programmable x/y coordinates available, which can be set in any desired distance over the full conversion range. Between two coordinates, the unit uses linear interpolation. Therefore it is advisable to use more coordinates in a range with strong curves and only a few coordinates where the curvature is less.To specify an individual linearization curve, the parameter LINEARISAZATION MODE must be set to either 1 QUADRANT or 4 QUADRANT (see following diagram).The parameters P1(X) to P24(X) are used to specify the coordinates on the x-axis. These are the measuring values that the unit normally would generate according to the actual input signal.Now enter the attached values to parameter P1(Y) to P24(Y). These are the values that the unit will generate instead of the x- values, i.e. P5(Y) replaces P5(X) etc.The X-Coordinates must use continuously increasing settings, i.e. P1(X) must have the lowest and P24(X) must have the highest setting. If the measured value is bigger than the last defined X-value, the corresponding Y-value is displayed.Mode: 1 Quadrant: Mode: 4 Quadrant:P1(X) must be set to zero. Linearization is only defined in the positive range and the negative range will be mirrored symmetric to central point. P1(X) can also be set to a negative value. If the measured value is smaller than P1(X), P1(Y) is displayed.Application Example:The picture below shows a watergate where the opening is picked up by means of an incremental encoder. We would like to display the clearance of the gate "d", but the existing encoder information is proportional to the angular information φ.6.3. Dimensions6.4. Technical Specifications:N o . 941233 E N ∙ J 18; S u b j e c t t o c h a n g e s .HeadquartersGermany Balluff GmbHSchurwaldstrasse 973765 Neuhausen a.d.F .Phone + 49 7158 173-0Fax +49 7158 5010******************US Service Center USABalluff Inc.8125 Holton Drive Florence, KY 41042Phone (859) 727-2200Toll-free 1-800-543-8390Fax (859) 727-4823****************************CN Service CenterChinaBalluff (Shanghai) trading Co., ltd.Room 1006, Pujian Rd. 145. Shanghai, 200127, P .R. China Phone +86 (21) 5089 9970Fax +86 (21) 5089 9975*******************.cnGlobal Service Center Germany Balluff GmbHSchurwaldstrasse 973765 Neuhausen a.d.F .Phone +49 7158 173-370Fax +49 7158 173-691******************。
乐彩750写真机操作维修指南[宝典]
![乐彩750写真机操作维修指南[宝典]](https://img.taocdn.com/s3/m/e797be7a1fb91a37f111f18583d049649b660eba.png)
乐彩750写真机操作维修指南乐彩750写真机操作维修指南750写真机常见故障及解决办法：以下是乐彩写真机 750H，天彩写真机，等国产进口750写真机故障的解析和维修下面以天彩750写真机为例：一、打图时出现方格断墨写真机光栅赃了，需用棉签沾清水擦洗上下光栅，应多擦几次洗净后用干棉签把水擦干。
二、写真机不可认墨水匣写真机解密卡松了需重新插好，或解密卡坏了。
三、打图错位1、皮带擦皮带轮卡，需调整皮带轮。
2、伺服电机坏了，需更换伺服电机。
3、铜环脏了，需清洗或更换铜环。
四、写真机喷头不出墨1、小车板发热，需关闭机器休整。
2、触电带坏了，需更换触电带。
3、喷头堵了，需抽洗喷头。
⒋墨管接口堵了，需拔下多插几次即可，⒌喷头干扰，互换喷头位置，和用纸巾垫在喷头与触电带之间来检查是那个喷头干扰，更换喷头。
⒍如出现四个喷头同时不出墨，在排除喷头干扰后还不出墨即为小车板坏了。
五、写真机测不到纸1、测纸器脏了，需用棉签沾清水擦洗。
2、测纸器没装好，需重装。
3、测纸器坏了，需更换测纸器。
4、小车板坏了，需更换。
六、写真机打图边线向一边斜1、伺服电机坏了，需更换伺服电机。
2、光栅感应器脏了，需用棉签沾清水擦洗。
光栅感应器坏了，需更换。
七、开机时小车架撞左边机架1、光栅感应器脏了，需清洗干净。
2、光栅感应器坏了，需更换。
3、数据线没插好，需多插几次。
八、写真机频繁测纸1、进纸传感器脏了，需清洗。
2、进纸传感器没插好与主板连接或接触不好。
3、进纸传感器坏了，需更换。
九、写真机打图时喷头滴墨1、喷头内空气没抽净，需多抽几次。
2、墨管接口吻合不好，需重新插好或更换接口。
3、喷头漏气，需查出何处漏气然后用胶水密封。
十、写真机打图时图面模糊静电干扰，（静电安全电压为三伏以内）十一、写真机打图时出现规则性断墨1、小车板不稳定。
2、喷头位置不对。
十二、常见英文报错1、Internal ERROR shutdown Bad carriage paper sensor(小车板或测纸器没插好接触不良)2、Internal ERROR shutdown Carriage Axis Failure(电机接触不良需重插或电机损坏)3、Internal ERROR shutdown CB LOLT 01RANGE LL:0(测纸器接触不好，需重插或更换测纸器)4、IMP assoservice: unexpected REQ(进纸传感器接触不良或损坏) 十三、打图时图面尺寸不对调整方法先按辅助功能菜单→效准菜单→图纸纵轴线→将默认数值83.82改动，注意图长了则将数字加大，图小了则将数字减小（注，改动时以小数改按每毫米改0.1为准）改后一定要保存。
futaba cgy750中文版说明书
介绍Futaba CGY750是一个组合的3轴陀螺仪，在一个盒子里装上了AVCS陀螺和磁头调速器。
它的尖端MEMS(微电子机械系统)传感器设计，超高速处理速度和先进的PID控制算法使其在尺寸、重量和性能方面领先于其他所有的陀螺仪。
CGY750已经被优化为无人直升机的工作。
保修和服务（美国）如果在设置或操作你的CGY750时候遇到任何的困难，请先查阅说明书，其次你也可以和你的经销商联系或者联系futaba的服务中心，传真和电话如下：或fax(217)-398-7721，tel (217)398-0007如果你无法解决这个问题，请将这个系统放置在它的原包装中，并附上一张纸条，对这些问题进行详细的描述。
在你的纸条上包括以下的内容：症状（包括出现的问题）系统（发射器、接收机、伺服器和模型号）模型（模型的名称）模型编号和数量你的名字，地址和电话号码将各自的问题发送到futaba授权服务中心双叶服务中心阿波罗1号3002号伊利诺伊州61822特征三轴陀螺和调速器在一个盒子里高速运转操作和极小的延迟具有更大的稳定性低姿态、小尺寸和轻重量陀螺仪和控制器的尺寸为44x29x12mm,13g使用128X36点的黑白OLED屏（有光显示），即使在阳光直射下仍有高亮度和对比度。
设置分为基础和专业的菜单，这基础的菜单是为初始设置，专业的菜单是为更多高级的设置。
当使用CIU-2接口时，固件可以从windows系统上跟新。
SBUS是兼容的，只需要一个的在这个总线接收机和CGY750控制盒之间为了操作陀螺部分采用先进的和自适应的PID控制回路小和低姿态三轴陀螺仪，21x21x8.5mm,8g舵（偏航）部分能够感应到角的速度，升到+/-1200度/秒。
兼容1520的模拟(70Hz)，1520数字(280Hz)和760数字(560Hz)的尾转子伺服系统。
3D和飞行运动模式前馈选项允许CGY750可以在操作期间进行其它的操作，这就导致了更精确的修正和精确的操作。
福彩体彩终端机操作
福彩体彩终端机操作福彩、体彩终端机操作介绍第一部分福利彩票福彩包括：七乐彩、3D、两步彩（固选又称为4D）、双色球、快乐8；其中七乐彩、双色球、快乐8不能随便按机选（按下机选就会出有价格的彩票）一、七乐彩每周一、三、五晚21：30开奖投注号码范围为01～30，七乐彩每期从30个号码中开出7个基本号码和1个特别号码作为中奖号码，七乐彩玩法即是竞猜开奖号码中的7个基本号码和1个特别号码，顺序不限。
2、开奖每周一、三、五21:30开奖操作方法：七乐彩→注数（1—5）单式多张票据（1—10）类型单式复式8 复式9复式10 复式11 复式124、桌面1 2 3 4 56 7 8 9 1011 12 13 14 1516 17 18 19 2021 22 23 24 2526 27 28 29 30注意事项：选几个数字就是复式几；用多张票据时，电脑显示的是一张票的金额；价格：每注2元，复式8—16元；复式9—72元；复式10—240元；复式11—660元；复式12—1584元；一等奖中7+0；二等奖中6+1；三等奖中6+0；四等奖中5+1；五等奖中5+0；六等奖中4+1；七等奖中4+0二、3D每日开奖注数期数倍数单选多张票据1 2 3 4 5 1 2 3 4 5 6 7 1 2 3 4 5 10 20 50 投注类型 1 2 3 4 5 6 7 8 9 10类型单选组选复选和组选通选和数选*99 9*9 99* **9 *9* 9**1D/百位1D/十位1D/个位2D/百十位2D/十个位2D/百个位＿﹟﹟﹟＿﹟﹟﹟＿﹟﹟＿﹟＿＿＿﹟＿注意事项：单选每注2元，复选每注12元。
操作举例：1、289 2单一组的操作方法：注数＿136 3D →类型＿256 倍数注意把下面各注的倍数都按照要求选好0782、机选5注单选3D: 先按机选---选择注数—确认按照客户要求可打出1D 2D 等…三、两步彩（固选又叫4D）注数倍数单选多张票据1 2 3 4 5 1 2 3 4 5 10 20 50 投注类型 1 2 3 4 5 6 7 8 9 10类型一步固选群选*999 9*99 99*9999* **99 99* 9**9 *9*9*99* 99** 二步全彩例子：选全彩0171 08操作步骤：选两步彩→全彩→0171两步→08 →确认四、双色球（单式投注是从1到33红色球号码中选择6个号码，从1到16蓝色球号码中选择1个号码6+1）复式投注（一）红色球号码复式：从红色球号码中选择7--20个号码，从蓝色球号码中选择1个号码，组合成多注投注号码的投注。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
注：1、机器更改设置完毕，如不保存设定数值机器重新开机后将恢复原来设置！ 2、打印黑色字符时如有颜色阴影应重新设置颜色静曲和颜色校准，先设置颜色静曲后设置颜色校准！ 3、机器开机之前确保接好地线，电脑及机器开机状态下且勿拔插数据线！ 4、为保证打印质量每天开机先进行颜色测试，然后进行喷头清洗！ 5、定期用卫生棉沾缝纫机油擦拭轨道；用棉棒沾纯净水擦拭光栅；抽完喷头后,一定要保证喷头和触点带电路干燥！蒙泰软件设置：1、在电脑COMS中设置ECP端口。
重启电脑按DEL进入INTEGRATED PERIPHERALS功能选项，将其中的PARALLEL PORT MODE设置为ECP，F10保存退出。
2、蒙泰中添加“ENCAD Novajet”-------“Novajet750”，（选择850机器时，打印机设定里面将纸张类型设置为高光相纸，墨水设置为CMYK （right））。
3、打开蒙泰：按“打印”（第五个图标）打印机设定打印端口选“FITE”或“LPT1”。